Post on 27-Sep-2020
DoorKing Model 9000 -
Elevations Drawings
Top Illustration: 9000
shown with Cantilevered Gate
Bottom Illustration: 9000
shown with V-Groove Track Gate
9000 - Top View
9000 - Side View
9000 - Front View
Layout 1
DoorKing Model 9000
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Entrance Drive
w/Access Device
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 2
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Entrance Drive
w/Access Device
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicle
Layout 3
Gate Style: V-Groove Track
DoorKing Model 90000
w/One-Way Free Exit Drive
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 4
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Drive
w/Free Exit
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 5
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry& Exit Device
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 6
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry& Exit Device
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 7
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry Device & Free Exit
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 8
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry Device & Free Exit
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 9
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry& Exit Device
w/Bi-parting Operator Mount
w/4' Loops for Normal Vehicles
Layout 10
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry& Exit Device
w/Bi-parting Operator Mount
w/4' Loops for Normal Vehicles
Layout 11
Gate Style: Cantilevered Gate
DoorKing Model 9000
w/Two-Way Drive
w/Entry Device & Free Exit
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 12
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Entrance Drive
w/Regular Turn-around
w/Telephone Entry System
w/DoorKing Card Reader/Keypad
w/Left-hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 13
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Entrance Drive
w/Off-set Turn-around
w/Telephone Entry System
w/DoorKing Card Reader/Keypad
w/Left-hand Operator Mount
w/4' Loops for Normal Vehicles
DOCUMENT HISTORY
DATE OF ORIGIN/RELEASE 05/22/2015
REV DESCRIPTION OF REVISION DATE
A UL 325 REVISIONS - UPDATES 03/31/2019
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
CONTENTS
NTS
NOT TO SCALE
CONCRETE
PAD
24.00
GA
TE
P
OS
T
FIL
LE
R P
AN
EL
GA
TE
P
OS
T
VEHICLE LANE
CONCRETE
PAD
24.00
3' tail-section
GA
TE
P
OS
T
GA
TE
P
OS
T
COUNTER BALANCE SECTION
CANTILEVERED SLIDE GATE
Photo-beams must
cover the entire
travel of the gate
in both directions.
Photo-beams must
cover the entire
travel of the gate
in both directions.
GA
TE
P
OS
T
VEHICLE LANE
SLIDE GATE WITH
V-GROOVE TRACK
Model : 9000
GRADE
GRADE
Photo-beams must
cover the entire
travel of the gate
in both directions.
FALL-OVER CATCH BRACKET
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
Photo-beams must
cover the entire
travel of the gate
in both directions.
GATE FALL-OVER BRACKET
REVERSING EDGE
COVERED GUIDE ROLLERS
COVERED GUIDE ROLLERS
COVERED WHEEL
FALL-OVER CATCH BRACKET
GATE FALL-OVER BRACKET
REVERSING EDGE
GATE FALL-OVER BRACKET
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
Photo-beams must
cover the entire
travel of the gate
in both directions.
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
FRONT VIEW
CONCRETE
PAD
26.00
CONCRETE
PAD
26.00
4.00 4.00
4.004.00
CHAINCHAIN
CHAIN
GA
TE
GA
TE
19.00
Door
King
9000
Door
King
9000
19.00
28.00
Door
King
9000
11.75
11.75
CHAIN
HEIGHT
7.75
CHAIN
HEIGHT
7.75
28.00
28.00
28.00
30.00 30.00
30.00 30.00
16.50
16.50
FRONT VIEW
SIDE VIEW
SIDE VIEW
11.75
11.75
11.75
GATE IS SHOWN WITHOUT PICKETS AND/OR
MESH. DISTANCE BETWEEN GATE PICKETS MUST
BE LESS THAN 2.25" APART OR SCREENED WITH MESH
FROM GRADE TO AT LEAST 72" OF THE GATE HEIGHT!
GATE IS SHOWN WITHOUT PICKETS AND/OR
MESH. DISTANCE BETWEEN GATE PICKETS MUST
BE LESS THAN 2.25" APART OR SCREENED WITH MESH
FROM GRADE TO AT LEAST 72" OF THE GATE HEIGHT!
Door
King
9000
16.50
Door
King
9000
19.00
28.00
26.00
CONCRETE PAD
1.00
1" MINIMUM
SPACING
BETWEEN
THE GATE
OPERATOR
AND THE
GATE !
TOP VIEW
FRONT VIEWSIDE VIEW
24.00
CONCRETE
PAD
CONCRETE
PAD
26.00
4.00
GATE
24.00
CHAIN
HEIGHT
7.75
30.00
16.50
19.00
8.00
Conduit
Area
13.00
14.00
12.00
Conduit
Area
CONCRETE
PAD
24.00
GA
TE
P
OS
T
FIL
LE
R P
AN
EL
GA
TE
P
OS
T
VEHICLE LANE
CONCRETE
PAD
24.00
3' tail-section
GA
TE
P
OS
T
GA
TE
P
OS
T
COUNTER BALANCE SECTION
CANTILEVERED SLIDE GATE
Photo-beams must
cover the entire
travel of the gate
in both directions.
Photo-beams must
cover the entire
travel of the gate
in both directions.
GA
TE
P
OS
T
VEHICLE LANE
SLIDE GATE WITH
V-GROOVE TRACK
Model : 9000
GRADE
GRADE
Photo-beams must
cover the entire
travel of the gate
in both directions.
FALL-OVER CATCH BRACKET
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
Photo-beams must
cover the entire
travel of the gate
in both directions.
GATE FALL-OVER BRACKET
REVERSING EDGE
COVERED GUIDE ROLLERS
COVERED GUIDE ROLLERS
COVERED WHEEL
FALL-OVER CATCH BRACKET
GATE FALL-OVER BRACKET
REVERSING EDGE
GATE FALL-OVER BRACKET
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
Photo-beams must
cover the entire
travel of the gate
in both directions.
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
FRONT VIEW
CONCRETE
PAD
26.00
CONCRETE
PAD
26.00
4.00 4.00
4.004.00
CHAINCHAIN
CHAIN
GA
TE
GA
TE
Door
King
9000
19.00
19.00
28.00
11.75
11.75
CHAIN
HEIGHT
7.75
CHAIN
HEIGHT
7.75
28.00
28.00
28.00
30.00 30.00
30.00 30.00
16.50
16.50
FRONT VIEW
SIDE VIEW
SIDE VIEW
11.75
11.75
11.75
GATE IS SHOWN WITHOUT PICKETS AND/OR
MESH. DISTANCE BETWEEN GATE PICKETS MUST
BE LESS THAN 2.25" APART OR SCREENED WITH MESH
FROM GRADE TO AT LEAST 72" OF THE GATE HEIGHT!
GATE IS SHOWN WITHOUT PICKETS AND/OR
MESH. DISTANCE BETWEEN GATE PICKETS MUST
BE LESS THAN 2.25" APART OR SCREENED WITH MESH
FROM GRADE TO AT LEAST 72" OF THE GATE HEIGHT!
Door
King
9000
16.50
Door
King
9000
19.00
28.00
26.00
CONCRETE PAD
1.00
1" MINIMUM
SPACING
BETWEEN
THE GATE
OPERATOR
AND THE
GATE !
TOP VIEW
FRONT VIEWSIDE VIEW
24.00
CONCRETE
PAD
CONCRETE
PAD
26.00
4.00
GATE
24.00
CHAIN
HEIGHT
7.75
30.00
16.50
19.00
8.00
Conduit
Area
13.00
14.00
12.00
Conduit
AreaREVERSING EDGE
ON TRAILING EDGE
OF GATE
REVERSING EDGE
ON LEADING EDGE
OF GATE
REVERSING EDGE ON
TRAILING EDGE OF GATE
REVERSING EDGE
ON TRAILING
EDGE OF GATE
REVERSING EDGE
LEADING EDGE
OF GATE
REVERSING EDGE
ON LEADING EDGE
OF GATE
REVERSING
EDGE
ON POSTREVERSING
EDGE
ON POST
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
REVERSING
EDGE
ON POST
PHOTO-BEAM LOCATION
MAXIMUM 27" FROM
GRADE & WITHIN 5" OF
GATE
REVERSING
EDGE
ON POST
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
ELEVATION VIEWS
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
12'
14'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Drive
w/Access Device
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 1
4'
4'
4'
4'
LAYOUT_SCALE
3/16" = 1'
SL
OD1
MP
VL
PB
PB
VL
SP
GT
3'
3'8'3'
TS
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 1
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Drive
w/Access Device
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 2
4'
4'
4'
MP
PB
SL
PB
OD1
VL
VL
GT
14'
3'8'3'
TS
4'
SP
12'
3'
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 2
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
OPEN/EXIT
LOOP
4' x 8'
14'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Drive
w/Free Exit
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 3
4'
4'
4'
4'
4'
4'
SL
PB
GT
VL
VL
VL
PB
3'
3'8'3'
TS
SP
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 3
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
OPEN/EXIT
LOOP
4' x 8'
14'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Drive
w/Free Exit
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 4
4'
4'
4'
4'
4'
4'
3'
3'8'3'
VL
VL
VL
TS
SL
SP
GT
PB
PB
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 4
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
12'
12'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry & Exit Device
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 5
4'
4'
4'
4'
3'
3'8'3'
14'
OD1
MP
TS
GT
PB
SL
SP
PB
VL
VL
OD1
MP
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 5
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
12'
12'
14'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry & Exit Device
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 6
4'
4'
4'
4'
3'
3'8'3'
MP
OD1 VL
VL
MP
OD1
PB
SL
TS
SPGT
PB
PB
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 6
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
OPEN/EXIT
LOOP
4' x 8'
14'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry Device & Free Exit
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 7
4'
4'
4'
4'
4'
4'
3'
3'8'3'
MP
OD1
SP
SL
GT
PB
SP
PB
VL
VL
VL
12'
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 7
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
OPEN/EXIT
LOOP
4' x 8'
12'
14'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry Device & Free Exit
w/Left-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 8
4'
4'
4'
4'
4'
4'
3'
3'8'3'
OD1
MP
PB
SP
TS
SL
GT
PB
VL
VL
VL
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 8
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
Photo-beam must cover the
entire travel of the gate!
REVERSING
LOOP
4' x 22'
REVERSING
LOOP
4' x 22'
12'
12'
28'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry & Exit Device
w/Bi-parting Operator Mount
w/4' Loops for Normal Vehicles
Layout 9
4'
4'
4'
4'
3'
3'
3'22'3'
MP
OD1
TS
GT
PB
SL
SL
TS
PB
GT
VL
VL
SPSP
MP
OD1
RE
RE
RE
RE
RE
RE
16" min.
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 9
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
Photo-beam must cover the
entire travel of the gate!
OPEN/EXIT
LOOP
4' x 22'
REVERSING
LOOP
4' x 22'
REVERSING
LOOP
4' x 22'
12'
28'
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/Two-Way Drive
w/Entry& Exit Device
w/Bi-parting Operator Mount
w/4' Loops for Normal Vehicles
Layout 10
4'
4'
4'
4'
4'
4'
3'
3'
3'22'3'
MP
OD1
TS
GTTS
GT
VL
VL
VL
SL
PB
PB
SP
SL
RE
RE
RE
RE
RERE
16" min.
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 10
NTS
NOT TO SCALE
Photo-beam must cover the
entire travel of the gate!
LAYOUT DESCRIPTION:
CANTILEVER GATE
DoorKing Model 9000
w/Two-Way Drive
w/Entry Device & Free Exit
w/Right-Hand Operator Mount
w/4' Loops for Normal Vehicles
Layout 11
20'
10'-6"
OD1
SL
MP
PB
PB
4'
4'
4'
4'
4'
4'
OPEN/EXIT
LOOP
4' x 14'
REVERSING
LOOP
4' x 14'
REVERSING
LOOP
4' x 14'
VL
VL
VL
TS
GT
SP
14' 3'3'
12'
RE
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
Layout 11
NTS
NOT TO SCALE
20'
TURN-AROUND
Shown as a example only.
Actual distances,
dimensions, and exact
location of curbing and
visitor phone island to be
determined by "Local
Authority Having
Jurisdiction."
OD2
OD1
MPMP
VL
Photo-beam must cover the
entire travel of the gate!
3'
PB
SP
SL
PB
GT
LAYOUT DESCRIPTION:
Gate Style: V-Groove Track
DoorKing Model 9000
w/One-Way Drive & Turn-around
w/Telephone Entry System
w/DoorKing Card Reader/Keypad
w/Left-hand Operator Mount
w/4' Loops for High Vehicles
Layout 12
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
4'
4'
4'
4'
VL
VL
ARMING LOOP
4' x 8'
4'
14'
RE
RE
TS
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
LAYOUT 12
NTS
NOT TO SCALE
20'
TURN-AROUND
Shown as a example only.
Actual distances,
dimensions, and exact
location of curbing and
visitor phone island to be
determined by "Local
Authority Having
Jurisdiction."
OD2
OD1
MPMP
LAYOUT DESCRIPTION:
Gate Style:V-Groove Track
DoorKing Model 9000
w/One-Way Drive & Off-set Turn-around
w/Telephone Entry System
w/DoorKing Card Reader/Keypad
w/Left-hand Operator Mount
w/4' Loops for High Vehicles
Layout 13
Photo-beam must cover the
entire travel of the gate!
3'
PB
SP
SL
PB
GT
REVERSING
LOOP
4' x 8'
REVERSING
LOOP
4' x 8'
4'
4'
4'
4'
VL
VL
VL
ARMING LOOP
4' x 8'
4'
14'
PB
RE
TS
RE
RE
16" min.
COMPONENTS
SL
Slide Gate Operator: DoorKing Model 9000
SW
Swing Gate Operator:
PK
Parking Barrier Operator:
PB
Photo Beam: DoorKing Model 8080-031
RE
Reversing Edge: DoorKing Model 8080-0xx
VL
Vehicle Detecting Loop - DoorKing - Type 9402-xxx
OD1
Opening Device 1: DoorKing DKProx Card Reader
OD2
Opening Device 2: DoorKing Telephone Entry Sys
OD3
Opening Device 3:
MP
Mounting Post: DoorKing Model 1200-xxx
SP Slide Gate Panel
SWP
Swing Gate Panel
GT Gate Travel
TS TAIL SECTION
GENERAL NOTES
120 Glasgow Avenue
Inglewood, California 90301
Phone Contact: 310-645-0023
Website: www.doorking.com
Email: ghendrix@doorking.com
● Automated vehicular gates shall be designed and installed to be in strict compliance with the UL 325 Safety Standard and the ASTM F2200 Construction Standard.
● Automated vehicular gates that do not meet the requirements of these standards shall not be allowed.
● This drawing is for the sole purpose of general gate operator foot-print and location, photo beam coverage and placement, and vehicular loop dimensions and placement. Drawings are not all inclusive or guaranteed to scale.
● No considerations have been made for grade, existing public utilities, landscape, drainage, site peculiarities, or requirements by the authority having jurisdiction, ie; Fire Marshall, Building Inspector, Street and Alley Depart- ments.
● Warning Signs must be installed and must be highly visible upon both entry and exit of the property, and must remain in place for the life of the gate operating system.
● Proper lane identification and vehicular direction signs should be highly visible upon entry onto the property.
● Gate dimensions, posts, guide rollers, photo beams, reversing edges, hinges, and other gate hardware may vary in size, dimension, and placement and should not be used as an exact reference.
● All loop sizing and placement dimensions indicated are solely intended for reference only, and not intended to be the final criterion for determining the loop sizing and placement on any automated vehicular gate project. DoorKing, Inc does not assume responsibility or liability for any installation with regard to equipment/system malfunction, vehicle detector loop sizing and placement, or consequent damages or injuries caused thereby.
● DoorKing, Inc. does not assume responsibility or liability for the installation and unauthorized changes to the design and operation of equipment, or alterations to the final site plan.
LAYOUT_DESCRIPTION
Layout 13
NTS
NOT TO SCALE