Post on 07-Mar-2020
www.ddg.tuwien.ac.at
Laser Manual
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
Fundamentals
Materials
Plastics e.g. .:
• AcrylicGSmax.12mm• AcrylicXTmax.2mm• Polystyrenemax.2mm
WoodenSurfacese.g.:
• Paperwoodmax.5mm• BalsaWoodmax.3mm
Papier e.g. .:
• Greycardboardmax.3mm• Finecardboardmax.4mm• Bristolpapermax.3mm
Absolut nicht verwendet werden können:
PVC-foils,MDF,stone,metal
SurfaceAreaoftheLasertable
1240x700mm(=maximumworkarea)
Fileformat
• CAD-drawings(Rhino/Autocad/..)• Pixelgraphics(toengrave)
In1960,TheodoreMainmanbuiltthefirstMachinethatusedtheconceptof„LightAmplifi-cationbyStimulatedEmissionofRadiation“.Theconceptallowstoproducelightwithpowedensitiesthataremillionsoftimeshigherthanthehighestconventionallyproducedcapacityandpowerdensity.
Thelaserallowsfordifferentmaterialswithlowmaterialstrengthtobecut,drawninto,orengraved.
Differentplasticsaremostappropriate,butpaper,woodensurfacescanalsobeused.
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
1.Carving(Red)Frame(othercolor) 2.Cuttinginside(blue)3.Cuttingoutside(green)
Drawing Preparation
PreparationfortheDrawing(e.g.RHINO)• Drawinginmm(intherightscale)• Drawtheframe(inthesizeoftheplate)anddrawthe
partstobecutinsidetheframe.• Nodoubleoverlappinglines!!(acleandrawing)• Cleanupandsimplifythedrawingtoshowonlythene-
cessarycutting-engravinglines• Savethedrawingthefollowingfilesthatmaybeopened
inRhino(dwg, dxf, usw...)oraspdforjpg.SaveAuto-caddrawingsinversion2007orolderversions.
Surfaceareaofthelasertable:L:1240mmW:700mm
LayersandColors
Thelaserwillreceiveinformationabouttheprintingjobandthereforecertaincolorsmustbeused.Eachcolorwillproduceadifferentcuttingperformance???(engravingorcutting)andwillbeperformedinthefollowingorder:
Order(CarvingandCutting)
1.Red > RGB 255 0 02.Blue > RGB0 0 2553.Green > RGB0 255 04.Magenta > RGB 255 0 255
Engraving
Engravingdoesnotworkforvectorgraphics,butonlyforflatsurfacelasering(e.g.photoorpattern)
Forengravingtheblackcolor(RGB000)orgrayscaleisused.
www.ddg.tuwien.ac.atTU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien www.ddg.tuwien.ac.at
Laser Manual
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
Thedrawingsmustbeinthecorrectscaleand units:
•OpenPropertiesat: >Datei>Eigenschaften>Einheiten
•Changetometricunitsinmillimeters(ifnecessary)
•IfthewindowwithScalingappears,confirmwithNo.
1. Checking the units
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
2. Printing Menu
PrintingMenu-Payattentiontotheorder
1. Openproperties(Eigenschaften).
2. Enter the width and height of the sheet to be cut. e.g. : 1000mmx700mm
3. Resolution600dpiStandard
4. OK
5. Activatethepreview(Ansichtsfenster)andclickonSET.Finally,clickon„MOVE„intheRhinooperationcolumn,undmovetheprintingwindowoverthedrawing.Whensettingthescale,makesurethatitis1:1.
6. PRINT
7. AfterclickingPRINTopentheTROTECJobontrolwindow.
5
1
600dpi
2
3
4
67
Assoonasthedrawingisreadyyoucanopenuptheprin-tingmenu.
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
3. Use the control-panel to place the laser printer head in the center over thematerial.
2. Ifthematerialisnotcompletelyflat,usetapetofixittothetable.
1. Place the materialinthe upper left corner of the table.
3. Positioning of the materials and set-up of the table height.
Control Panel
4. Themetalpiece(spaceseparationtool)mustbehungontothelaserprinterheadasshownintheimageabove.Thenthetablemustbecarefullymovedupstep-by-stepuntilthemetalpiecefalls off.
Inorderfortheburningpointofthelaserbeamtobeac-curate,thedistancefromthelensetothematerialmustbeinstalled.Ifmaterialthicknessischangedthennewsettingsmustbeinstalled.
TableHeight:Up
Down
FrontLeft-RightBack
Standby-Function
3 2
1
1
3
24
4 Gas 1 (checkparameterswithmaterialcatalogue)
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
Programtostartthejob
TheprintingjobissenttotheLaser´sprogram(TROTEC-Engraver).
1. Delete all the old jobs with delete button.
2. Double-clickonthechosenlaserfile(youcanviewthefileinthesmallpreviewwindow).
The white area corresponds to the work area of the laser. Thefilemustbeplacedintheupperleftcornerofthewhitearea.
1 2
Preview Window
4. TROTEC JobControl
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
1.Doubleclickonthewhiteareatoopenthematerialpro-pertieswindow.Enterthematerialnameandthickness.
2.Ifyouopenthe„All“(Alle)menu,youcanchangethe
values for the colors.
Thevaluesmustbetakenfromthelistthatislocatednearthecomputer.
IMPORTANT:Gas1mustbeenteredintothe„Zublasung“column.
Example:
Valuesforblackcardboardwith2mmthickness. Leistung(Power)=70,00Geschwindigkeit(Speed)=1,25PP/Hz=5000Durchgänge(Stages)=1Zublasung(Ventilation)=Gas1Korrektur(Correction)=0Z-Offset=0,00mm
70,001,255000Hz1Gas100,0mm
1
2
Esc = zurück
5. Installation of Material Preferences
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
Ifthedrawingsarecomplicatedwithmanylines,thevectorclassification(Vektorsortierung)shouldbeused.Thismeansthatthelineswillbecutinaspecificorder.
1.RightclickovertheJobwindow(greyorblack)>Vek-torsortierung
2. Start
1
2
6. Vector Categorization (optional)
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
PayingwithQuick
Thelasercuttingprocesscanbestartedafterpayingattheslotmachine.5minutesbeforeyourtimeisup,thesignallightturnsorange,soyoucanestimateifyouneedmoretimetocutallyourparts.
PayingwithaQuick-PrepaidCard:
1. YoucangetyourQuick-Prepaidcardat:PayLife,Marxergasse1B,1030WienoryoucanuseacashcardwithaQuick-function.
2. PutyourQuick-PrepaidCardintheslotmachine.Onthedisplayyouseethebalanceofyourcard.
3. Press buttons + and – to select laser 1 or 2.
4. Pressbuttons+and–todebitanamount.
5. PressOK.
6. Whenthedisplaysays„Karteentfernen“,youcanremoveyourcard.
7. Youcanstartthecuttingprocessbypressingplay.
7. Payment
TU Wien / E2642 / Institut für Kunst und Gestaltung / Abteilung Modellbau Karlsplatz 13 A-1040 Wien http://kunst2.tuwien.ac.at/
Onceallthesettingshavebeenadjusted,thelaserprintercan be started.
Start
Pause
Thejobcanbepausedifyouwanttoremoveparts.Thela-sercanbestartedagainbypressingII(Pause)intheTrotecJobControlProgram(onthecomupter).
Thelasermayonlybeusedundersupervision.Ifyouleavetheroom,pausetheprintingjob.
Cancel
8. Starting-up the Laser
Steuerpult