Post on 03-Sep-2014
Mar 28 2007
Service Manual
iR5075/5065/5055 Series
ApplicationThis manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair
of products. This manual covers all localities where the products are sold. For this reason, there may be information in this
manual that does not apply to your locality.
CorrectionsThis manual may contain technical inaccuracies or typographical errors due to improvements or changes in products. When
changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need
arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition
of this manual.
The following paragraph does not apply to any countries where such provisions are inconsistent with local law.
TrademarksThe product names and company names used in this manual are the registered trademarks of the individual companies.
CopyrightThis manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied, reproduced or
translated into another language, in whole or in part, without the written consent of Canon Inc.
COPYRIGHT © 2001 CANON INC.Printed in Japan
CautionUse of this manual should be strictly supervised to avoid disclosure of confidential information.
Introduction
Symbols UsedThis documentation uses the following symbols to indicate special information:
Symbol Description
Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning.
Indicates an item requiring care to avoid electric shocks.
Indicates an item requiring care to avoid combustion (fire).
Indicates an item prohibiting disassembly to avoid electric shocks or problems.
Indicates an item requiring disconnection of the power plug from the electric outlet.
Indicates an item intended to provide notes assisting the understanding of the topic in question.
Indicates an item of reference assisting the understanding of the topic in question.
Provides a description of a service mode.
Provides a description of the nature of an error indication.
Memo
REF.
Introduction
The following rules apply throughout this Service Manual:1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with refer-
ence to the timing of operation.In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates thedirection of the electric signal.The expression "turn on the power" means flipping on the power switch, closing the front door, and closing the delivery unit door, which results insupplying the machine with power.
2. In the digital circuits, '1'is used to indicate that the voltage level of a given signal is "High", while '0' is used to indicate "Low".(The voltage value, how-ever, differs from circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD signal goes on when '0'.In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field. Therefore, the operations of the microprocessorsused in the machines are not discussed: they are explained in terms of from sensors to the input of the DC controller PCB and from the output of theDC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product improvement or other purposes, and major changes will be com-municated in the form of Service Information bulletins.All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant Service Information bulletins and beable to identify and isolate faults in the machine."
Contents
Contents
Chapter 1 Introduction
1.1 System Construction ..................................................................................................................................1- 11.1.1 System Configuration with Pickup/Delivery Accessories (230V)EUR .....................................................................1- 11.1.2 System Configuration with Printing/Transmission Accessories (230V)EUR ...........................................................1- 11.1.3 Functions and Printing/Transmission Accessories (230V) ......................................................................................1- 2
1.2 Product Specifications ................................................................................................................................1- 31.2.1 Names of Parts........................................................................................................................................................1- 3
1.2.1.1 External view............................................................................................................................................................................ 1- 31.2.1.2 Cross-Section .......................................................................................................................................................................... 1- 5
1.2.2 Using the Machine................................................................................................................................................... 1- 71.2.2.1 Turning On the Power Switch .................................................................................................................................................. 1- 71.2.2.2 Turning Off the Power Switch .................................................................................................................................................. 1- 71.2.2.3 Control Panel ........................................................................................................................................................................... 1- 9
1.2.3 User Mode Items .....................................................................................................................................................1- 91.2.3.1 Common Settings .................................................................................................................................................................... 1- 91.2.3.2 Timer Settings........................................................................................................................................................................ 1- 111.2.3.3 Adjustment/Cleaning.............................................................................................................................................................. 1- 111.2.3.4 Report Output ........................................................................................................................................................................ 1- 111.2.3.5 System Control Settings ........................................................................................................................................................ 1- 121.2.3.6 Copier Specifications ............................................................................................................................................................. 1- 141.2.3.7 Transmission/Reception Settings .......................................................................................................................................... 1- 151.2.3.8 Box Settings........................................................................................................................................................................... 1- 161.2.3.9 Printer Settings ...................................................................................................................................................................... 1- 161.2.3.10 Address Book Settings......................................................................................................................................................... 1- 181.2.3.11 Voice Guide Settings............................................................................................................................................................ 1- 19
1.2.4 Maintenance by the User.......................................................................................................................................1- 191.2.4.1 Cleaning................................................................................................................................................................................. 1- 191.2.4.2 Checks ................................................................................................................................................................................... 1- 20
1.2.5 Safety ....................................................................................................................................................................1- 211.2.5.1 Safety of the Machine's Laser Unit ........................................................................................................................................ 1- 211.2.5.2 CDRH Regulations................................................................................................................................................................. 1- 211.2.5.3 Handling the Machine's Laser Unit ........................................................................................................................................ 1- 221.2.5.4 Safety of Toner ...................................................................................................................................................................... 1- 22
1.2.6 Product Specifications ...........................................................................................................................................1- 221.2.6.1 Product Specifications ........................................................................................................................................................... 1- 22
1.2.7 Function List ..........................................................................................................................................................1- 241.2.7.1 Paper Types........................................................................................................................................................................... 1- 241.2.7.2 Printing Speed ....................................................................................................................................................................... 1- 241.2.7.3 Paper Types/Printing Speed (K paper) .................................................................................................................................. 1- 25
Chapter 2 Installation
2.1 Making Pre-Checks ....................................................................................................................................2- 12.1.1 Selecting the installation space ...............................................................................................................................2- 12.1.2 Combination Table of Accessories ..........................................................................................................................2- 2
2.2 Unpacking and Installation .........................................................................................................................2- 32.2.1 Unpacking and installation procedure ..................................................................................................................... 2- 32.2.2 Unpacking................................................................................................................................................................2- 32.2.3 Installation of Scanner .............................................................................................................................................2- 42.2.4 Installation of Fixing Assembly ................................................................................................................................2- 52.2.5 Checking of Charging Assembly and Dustproof Glass ...........................................................................................2- 62.2.6 Installation of Developing Assembly .......................................................................................................................2- 72.2.7 Installation of Pickup Assembly ..............................................................................................................................2- 8
Contents
2.2.8 Attaching Deck Pressure Plate ...............................................................................................................................2- 82.2.9 Setting Toner Container ..........................................................................................................................................2- 92.2.10 Connecting the Cable.............................................................................................................................................2- 92.2.11 Checking the Environment Switch .......................................................................................................................2- 102.2.12 Attaching the Label ..............................................................................................................................................2- 102.2.13 Turning On the Main Power Switch......................................................................................................................2- 112.2.14 Toner Stirring .......................................................................................................................................................2- 112.2.15 Media Cassette Settings ......................................................................................................................................2- 112.2.16 Index Paper Attachment.......................................................................................................................................2- 112.2.17 Changing the Media Size of the Front Deck (Left/Right)......................................................................................2- 122.2.18 Image/Operation Check in User Mode.................................................................................................................2- 122.2.19 Adjustment of Image Left End Margin..................................................................................................................2- 122.2.20 Adjustment of image leading edge margin...........................................................................................................2- 142.2.21 Mounting of the Host Machine .............................................................................................................................2- 14
2.3 Checking the Connection to the Network ................................................................................................. 2- 162.3.1 Overview................................................................................................................................................................2- 162.3.2 Checking the Connection to the Network...............................................................................................................2- 162.3.3 Using the Ping Command......................................................................................................................................2- 172.3.4 Making a Check Using the Remote Host Address.................................................................................................2- 17
2.4 Troubleshooting the Network ................................................................................................................... 2- 172.4.1 Troubleshooting the Network ................................................................................................................................2- 172.4.2 Checking the Connection of the Network Cable ...................................................................................................2- 172.4.3 Making a Check Using a Loopback Address ........................................................................................................2- 172.4.4 Making a Check Using a Local Host Address .......................................................................................................2- 17
2.5 Installing the Copy Tray............................................................................................................................ 2- 172.5.1 Confirming the contents .........................................................................................................................................2- 172.5.2 Power off of the host machine ...............................................................................................................................2- 182.5.3 Installation procedure.............................................................................................................................................2- 18
2.6 Installing the Card Reader........................................................................................................................ 2- 212.6.1 Notice At Installation ..............................................................................................................................................2- 212.6.2 Confirming the contents .........................................................................................................................................2- 212.6.3 Power off of the host machine ...............................................................................................................................2- 222.6.4 Installation procedure.............................................................................................................................................2- 222.6.5 Installing for imageWARE Accounting Manager ....................................................................................................2- 25
2.7 Installing the Original Holder .................................................................................................................... 2- 252.7.1 Checking Contents ................................................................................................................................................2- 252.7.2 Installation Procedure ...........................................................................................................................................2- 262.7.3 Checking Contents ................................................................................................................................................2- 272.7.4 Installation Procedure ...........................................................................................................................................2- 27
2.8 Installing the Reader Heater..................................................................................................................... 2- 282.8.1 Checking the Contents...........................................................................................................................................2- 282.8.2 Power off of the host machine ...............................................................................................................................2- 282.8.3 Installation Procedure ............................................................................................................................................2- 29
2.9 Installing the Cassette Heater .................................................................................................................. 2- 322.9.1 Checking Components...........................................................................................................................................2- 322.9.2 Power off of the host machine ...............................................................................................................................2- 332.9.3 Installation Procedure of the Cassette Heater .......................................................................................................2- 33
2.10 Installing the Deck Heater ...................................................................................................................... 2- 382.10.1 Checking the Parts to Install ................................................................................................................................2- 382.10.2 Turning Off the Host Machine ..............................................................................................................................2- 39
2.11 Installing the Deck Heater (Large Deck)................................................................................................. 2- 392.11.1 Checking the Parts to Install ................................................................................................................................2- 392.11.2 Turning Off the Host Machine ..............................................................................................................................2- 40
2.12 Installing the Voice Guidance Kit ............................................................................................................ 2- 402.12.1 A point to keep in mind at installation...................................................................................................................2- 40
Contents
2.12.2 Checking the Contents ........................................................................................................................................2- 402.12.3 Power off of the host machine .............................................................................................................................2- 412.12.4 Installation Procedure ..........................................................................................................................................2- 41
Chapter 3 Basic Operation
3.1 Construction ...............................................................................................................................................3- 13.1.1 Functional Construction...........................................................................................................................................3- 13.1.2 Wiring Diagram of the Major PCBs..........................................................................................................................3- 13.1.3 Controlling the Main Motor (M2) ..............................................................................................................................3- 2
3.2 Basic Sequence..........................................................................................................................................3- 33.2.1 Basic Sequence of Operation (at power-on; 30-sec start-up mode) .......................................................................3- 33.2.2 Basic Sequence of Operation (at power-on; low-temperature start-up mode) ........................................................3- 33.2.3 Basic Sequence of Operation (at power-on; high-humidity start-up mode)............................................................. 3- 43.2.4 Basic Sequence of Operation (at time of copying/printing) .....................................................................................3- 5
Chapter 4 Main Controller
4.1 Construction ...............................................................................................................................................4- 14.1.1 Construction and Mechanisms ................................................................................................................................4- 1
4.2 Construction of the Electrical Circuitry........................................................................................................4- 14.2.1 Main Controller PCB................................................................................................................................................ 4- 14.2.2 HDD.........................................................................................................................................................................4- 2
4.3 Start-Up Sequence .....................................................................................................................................4- 44.3.1 Overview..................................................................................................................................................................4- 44.3.2 Start-Up Sequence ..................................................................................................................................................4- 4
4.4 Shut-Down Sequence.................................................................................................................................4- 64.4.1 Overview..................................................................................................................................................................4- 64.4.2 Flow of Operation ....................................................................................................................................................4- 6
4.5 Image Processing.......................................................................................................................................4- 64.5.1 Overview of the Image Flow ....................................................................................................................................4- 64.5.2 Construction of the Image Processing Module........................................................................................................4- 74.5.3 Reader Unit Input Image Processing.......................................................................................................................4- 74.5.4 Compression/ Extension/ Editing Block...................................................................................................................4- 84.5.5 Printer unit Output Image Processing......................................................................................................................4- 8
4.6 Flow of Image Data ....................................................................................................................................4- 94.6.1 Flow of Image Data According to Copy Functions ..................................................................................................4- 94.6.2 Flow of Image Data for the Box Function ................................................................................................................4- 94.6.3 Flow of Image Data for the SEND Function ..........................................................................................................4- 104.6.4 Flow of Image Data for the Fax Transmission.......................................................................................................4- 104.6.5 Flow of Image Data for the Fax Reception Function .............................................................................................4- 114.6.6 Flow of Image Data for the PDL Function .............................................................................................................4- 12
4.7 Parts Replacement Procedure .................................................................................................................4- 134.7.1 Main Controller Box ...............................................................................................................................................4- 13
4.7.1.1 Before Removing the Main Controller Box............................................................................................................................. 4- 134.7.1.2 Removing the Main Controller Box ........................................................................................................................................ 4- 13
4.7.2 Main Controller PCB.............................................................................................................................................. 4- 134.7.2.1 Before Removing the Main Controller PCB ........................................................................................................................... 4- 134.7.2.2 Removing the Main Controller PCB ....................................................................................................................................... 4- 134.7.2.3 When Replacing the Main Controller PCB............................................................................................................................. 4- 14
4.7.3 SDRAM..................................................................................................................................................................4- 144.7.3.1 Before Removing the SDRAM ............................................................................................................................................... 4- 144.7.3.2 Removing the SDRAM........................................................................................................................................................... 4- 14
4.7.4 Boot ROM..............................................................................................................................................................4- 144.7.4.1 Before Removing the Boot ROM ........................................................................................................................................... 4- 144.7.4.2 Removing the Boot ROM ....................................................................................................................................................... 4- 14
Contents
4.7.5 HDD .......................................................................................................................................................................4- 154.7.5.1 Before Removing HDD .......................................................................................................................................................... 4- 154.7.5.2 Removing the HDD ................................................................................................................................................................ 4- 154.7.5.3 After Replacing the HDD........................................................................................................................................................ 4- 15
4.7.6 Video PCB .............................................................................................................................................................4- 154.7.6.1 Before Removing the Video PCB........................................................................................................................................... 4- 154.7.6.2 Removing the Video PCB ...................................................................................................................................................... 4- 15
4.7.7 Controller Fan ........................................................................................................................................................4- 164.7.7.1 Before Removing the Controller Cooling Fan ........................................................................................................................ 4- 164.7.7.2 Removing the Controller Cooling Fan.................................................................................................................................... 4- 16
Chapter 5 Original Exposure System
5.1 Construction ............................................................................................................................................... 5- 15.1.1 Specifications, Controls, and Functions...................................................................................................................5- 15.1.2 Major Components...................................................................................................................................................5- 15.1.3 Construction of the Control System .........................................................................................................................5- 25.1.4 Reader Controller PCB ............................................................................................................................................5- 3
5.2 Basic Sequence ......................................................................................................................................... 5- 45.2.1 Basic Sequence of Operations ................................................................................................................................5- 45.2.2 Basic Sequence of Operation in Response to a Press on the Start Key .................................................................5- 5
5.3 Various Control........................................................................................................................................... 5- 55.3.1 Controlling the Scanner Drive System.....................................................................................................................5- 5
5.3.1.1 Overview .................................................................................................................................................................................. 5- 55.3.1.2 Controlling the Scanner Motor ................................................................................................................................................. 5- 6
5.3.2 Enlargement/Reduction ...........................................................................................................................................5- 75.3.2.1 Changing the Magnification in Main Scanning Direction.......................................................................................................... 5- 75.3.2.2 Changing the Magnification in Sub Scanning Direction ........................................................................................................... 5- 7
5.3.3 Controlling the Scanning Lamp................................................................................................................................5- 85.3.3.1 Overview .................................................................................................................................................................................. 5- 85.3.3.2 Scanning Lamp ........................................................................................................................................................................ 5- 85.3.3.3 Controlling the Activation ......................................................................................................................................................... 5- 9
5.3.4 Detecting the Size of Originals.................................................................................................................................5- 95.3.4.1 Overview .................................................................................................................................................................................. 5- 95.3.4.2 Points of Measurement Used for Original Size Identification................................................................................................... 5- 95.3.4.3 Overview of Operation ........................................................................................................................................................... 5- 10
5.3.5 Dirt Sensor Control ................................................................................................................................................5- 125.3.5.1 Dust Detection in Stream Reading Mode............................................................................................................................... 5- 125.3.5.2 White Plate Dust Detection Control ....................................................................................................................................... 5- 13
5.3.6 Image Processing ..................................................................................................................................................5- 145.3.6.1 Overview ................................................................................................................................................................................ 5- 145.3.6.2 CCD Drive.............................................................................................................................................................................. 5- 155.3.6.3 CCD Output Gain Correction, Offset Correction .................................................................................................................... 5- 155.3.6.4 CCD Output A/D Conversion ................................................................................................................................................. 5- 155.3.6.5 Outline of Shading Correction................................................................................................................................................ 5- 155.3.6.6 Shading Adjustment............................................................................................................................................................... 5- 165.3.6.7 Shading Correction ................................................................................................................................................................ 5- 16
5.4 Parts Replacement Procedure ................................................................................................................. 5- 175.4.1 CCD Unit................................................................................................................................................................5- 17
5.4.1.1 Before Removing the CCD Unit ............................................................................................................................................. 5- 175.4.1.2 Removing the CCD Unit......................................................................................................................................................... 5- 175.4.1.3 When Replacing the CCD Unit .............................................................................................................................................. 5- 17
5.4.2 Copyboard glass ....................................................................................................................................................5- 185.4.2.1 Removing the Copyboard Glass ............................................................................................................................................ 5- 185.4.2.2 When Replacing the Copyboard Glass.................................................................................................................................. 5- 18
5.4.3 Scanning Lamp......................................................................................................................................................5- 185.4.3.1 Before Removing the Scanning Lamp ................................................................................................................................... 5- 185.4.3.2 Removing the Scanning Lamp............................................................................................................................................... 5- 185.4.3.3 When Replacing the Scanning Lamp..................................................................................................................................... 5- 19
Contents
5.4.4 Reader Controller PCB..........................................................................................................................................5- 195.4.4.1 Before Removing the Reader Controller PCB ....................................................................................................................... 5- 195.4.4.2 Removing the Reader Controller PCB ................................................................................................................................... 5- 195.4.4.3 After Replacing the Reader Controller PCB........................................................................................................................... 5- 20
5.4.5 Interface PCB ........................................................................................................................................................5- 205.4.5.1 Before Removing the Interface PCB...................................................................................................................................... 5- 205.4.5.2 Removing the Interface PCB ................................................................................................................................................. 5- 20
5.4.6 Memory PCB .........................................................................................................................................................5- 215.4.6.1 Before Removing the Memory PCB....................................................................................................................................... 5- 215.4.6.2 Removing the memory PCB .................................................................................................................................................. 5- 21
5.4.7 Inverter PCB ..........................................................................................................................................................5- 215.4.7.1 Before removing the inverter PCB ......................................................................................................................................... 5- 215.4.7.2 Removing the Inverter PCB ................................................................................................................................................... 5- 215.4.7.3 After Replacing the Inverter PCB........................................................................................................................................... 5- 22
5.4.8 Scanner Motor .......................................................................................................................................................5- 225.4.8.1 Before Removing the Scanner Motor..................................................................................................................................... 5- 225.4.8.2 Removing the Scanner Motor ................................................................................................................................................ 5- 225.4.8.3 Mounting the Scanner Motor.................................................................................................................................................. 5- 23
5.4.9 ADF Open/Close Sensor .......................................................................................................................................5- 235.4.9.1 Before Removing the ADF Open/Close Sensor..................................................................................................................... 5- 235.4.9.2 Removing the ADF Open/Close Sensor ................................................................................................................................ 5- 23
5.4.10 Scanner HP Sensor .............................................................................................................................................5- 235.4.10.1 Before Removing the Scanner HP Sensor........................................................................................................................... 5- 235.4.10.2 Removing the Mirror Base HP Sensor ................................................................................................................................. 5- 23
5.4.11 Original Size Sensor ............................................................................................................................................5- 245.4.11.1 Before Removing the Original Size Sensor.......................................................................................................................... 5- 245.4.11.2 Removing the original size sensor ....................................................................................................................................... 5- 24
5.4.12 Cooling Fan .........................................................................................................................................................5- 255.4.12.1 Before Removing the Cooling Fan ....................................................................................................................................... 5- 255.4.12.2 Removing the Cooling Fan................................................................................................................................................... 5- 25
5.4.13 Scanner Drive Cable............................................................................................................................................5- 255.4.13.1 Outline.................................................................................................................................................................................. 5- 255.4.13.2 Before Removing the Scanner Drive Cable ......................................................................................................................... 5- 255.4.13.3 Removing the Scanner Drive Cable..................................................................................................................................... 5- 255.4.13.4 Fitting the Scanner Drive Cable ........................................................................................................................................... 5- 285.4.13.5 Adjusting the Position of the No. 1/No. 2 Mirror Base.......................................................................................................... 5- 28
5.4.14 Waste Toner Box Holder .....................................................................................................................................5- 295.4.14.1 Before Removing the Collecting Toner Bottle Holder .......................................................................................................... 5- 295.4.14.2 Removing the Collecting Toner Bottle Holder ...................................................................................................................... 5- 29
Chapter 6 Laser Exposure
6.1 Construction ...............................................................................................................................................6- 16.1.1 Overview..................................................................................................................................................................6- 16.1.2 Major Components ..................................................................................................................................................6- 1
6.2 Basic Sequence..........................................................................................................................................6- 26.2.1 Basic Sequence of Operation (laser exposure)....................................................................................................... 6- 2
6.3 Various Controls .........................................................................................................................................6- 26.3.1 Controlling the Laser Activation Timing ...................................................................................................................6- 2
6.3.1.1 Generating the Sync Signal ..................................................................................................................................................... 6- 26.3.1.2 Flow of the Sync Signal ........................................................................................................................................................... 6- 2
6.3.2 Controlling the Intensity of Laser Light ....................................................................................................................6- 26.3.2.1 Controlling the Laser Intensity ................................................................................................................................................. 6- 26.3.2.2 APC Control ............................................................................................................................................................................. 6- 3
6.3.3 Controlling the Laser Scanner Motor.......................................................................................................................6- 46.3.3.1 Controlling the Laser Scanner Motor ....................................................................................................................................... 6- 4
6.4 Parts Replacement Procedure ...................................................................................................................6- 56.4.1 Laser Scanner Unit..................................................................................................................................................6- 5
6.4.1.1 Removing the Laser Scanner Unit ........................................................................................................................................... 6- 5
Contents
6.4.1.2 When Replacing the Laser Scanner Unit................................................................................................................................. 6- 5
Chapter 7 Image Formation
7.1 Construction ............................................................................................................................................... 7- 17.1.1 Overview..................................................................................................................................................................7- 17.1.2 Major Components...................................................................................................................................................7- 1
7.2 Image Formation Process .......................................................................................................................... 7- 17.2.1 Overview..................................................................................................................................................................7- 1
7.3 Basic Sequence ......................................................................................................................................... 7- 27.3.1 At Power-On ............................................................................................................................................................7- 27.3.2 At Time of Printing ...................................................................................................................................................7- 3
7.4 Potential Control ......................................................................................................................................... 7- 37.4.1 Overview..................................................................................................................................................................7- 37.4.2 Copier/Printer Potential Control ...............................................................................................................................7- 37.4.3 Determining the Primary Current .............................................................................................................................7- 67.4.4 Determining the Laser Output..................................................................................................................................7- 67.4.5 Determining the Developing Bias.............................................................................................................................7- 67.4.6 APC Correction ........................................................................................................................................................7- 77.4.7 Adjusting the Density in Various Modes ..................................................................................................................7- 7
7.5 Charging Mechanism ................................................................................................................................. 7- 87.5.1 Controlling Pre-Exposure LED.................................................................................................................................7- 8
7.5.1.1 Pre-Exposure LED Control ...................................................................................................................................................... 7- 87.5.2 Primary Charging Mechanism..................................................................................................................................7- 9
7.5.2.1 Overview .................................................................................................................................................................................. 7- 97.5.2.2 Primary Charging Assembly Cleaning Mechanism.................................................................................................................. 7- 97.5.2.3 Others .................................................................................................................................................................................... 7- 10
7.5.3 Dust-Collecting Roller Bias ....................................................................................................................................7- 107.5.3.1 Overview ................................................................................................................................................................................ 7- 10
7.5.4 Pre-Transfer Charging Mechanism........................................................................................................................7- 117.5.4.1 Overview ................................................................................................................................................................................ 7- 117.5.4.2 Controlling the Output to Suit the Environment (fuzzy control) .............................................................................................. 7- 117.5.4.3 Pre-Transfer Charging Assembly Cleaning Mechanism ........................................................................................................ 7- 127.5.4.4 Others .................................................................................................................................................................................... 7- 12
7.6 Drum Cleaner Unit.................................................................................................................................... 7- 127.6.1 Overview................................................................................................................................................................7- 127.6.2 Detecting the State (full) of the Collecting Toner Case..........................................................................................7- 137.6.3 Drum/Separation Claw Bias Control ......................................................................................................................7- 14
7.7 Developing Assembly............................................................................................................................... 7- 147.7.1 Controlling the Developing Assembly Drive...........................................................................................................7- 147.7.2 Controlling the Developing Bias.............................................................................................................................7- 147.7.3 Detecting the Toner Level and Controlling Toner Supply ......................................................................................7- 15
7.8 Transfer Mechanism................................................................................................................................. 7- 167.8.1 Transfer Charging Mechanism...............................................................................................................................7- 16
7.8.1.1 Overview ................................................................................................................................................................................ 7- 167.8.1.2 Controlling the Output to Suit the Environment (fuzzy control) .............................................................................................. 7- 167.8.1.3 Transfer Charging Assembly Cleaning Mechanism............................................................................................................... 7- 177.8.1.4 Others .................................................................................................................................................................................... 7- 17
7.9 Separation Mechanism............................................................................................................................. 7- 187.9.1 Separation Charging Mechanism...........................................................................................................................7- 18
7.9.1.1 Overview ................................................................................................................................................................................ 7- 187.9.1.2 Correcting the Output to Suit the Environment and the Drum Surface Potential ................................................................... 7- 187.9.1.3 Others .................................................................................................................................................................................... 7- 19
7.10 Parts Replacement Procedure ............................................................................................................... 7- 207.10.1 Process Unit.........................................................................................................................................................7- 20
7.10.1.1 Before Removing Process Unit ............................................................................................................................................ 7- 207.10.1.2 Removing Process Unit ....................................................................................................................................................... 7- 20
Contents
7.10.1.3 Mounting Process Unit ........................................................................................................................................................ 7- 207.10.2 Pre-Exposure Lamp.............................................................................................................................................7- 21
7.10.2.1 Before Removing Pre-Exposure Lamp ............................................................................................................................... 7- 217.10.2.2 Removing Pre-Exposure Lamp ........................................................................................................................................... 7- 217.10.2.3 Cleaning Primary Toner Blocking Sheet ............................................................................................................................. 7- 21
7.10.3 Primary Charging Assembly ................................................................................................................................7- 217.10.3.1 Before Removing Primary Charging Assembly.................................................................................................................... 7- 217.10.3.2 Removing Primary Charging Assembly .............................................................................................................................. 7- 21
7.10.4 Pre-Transfer Charging Assembly ........................................................................................................................7- 227.10.4.1 Before Removing Pre-Transfer Charging Assembly ........................................................................................................... 7- 227.10.4.2 Removing Pre-Transfer Charging Assembly ....................................................................................................................... 7- 22
7.10.5 Photosensitive Drum............................................................................................................................................7- 227.10.5.1 Points to Note When Handling Photosensitive Drum .......................................................................................................... 7- 227.10.5.2 Before Removing Photosensitive Drum ............................................................................................................................... 7- 227.10.5.3 Removing Photosensitive Drum .......................................................................................................................................... 7- 227.10.5.4 Cleaning Photosensitive Drum ............................................................................................................................................ 7- 23
7.10.6 Drum Motor..........................................................................................................................................................7- 237.10.6.1 Before Removing Drum Motor ............................................................................................................................................ 7- 237.10.6.2 Removing Drum Motor ........................................................................................................................................................ 7- 23
7.10.7 Photosensitive Drum Heater................................................................................................................................7- 247.10.7.1 Points to Note When Handling Photosensitive Drum .......................................................................................................... 7- 247.10.7.2 Before Removing Photosensitive Drum Heater .................................................................................................................. 7- 247.10.7.3 Removing Drum Heater ...................................................................................................................................................... 7- 247.10.7.4 Points to Note When Mounting Drum Heater ...................................................................................................................... 7- 24
7.10.8 Cleaning Blade ....................................................................................................................................................7- 247.10.8.1 Configuration........................................................................................................................................................................ 7- 247.10.8.2 Before Removing Cleaning Blade ....................................................................................................................................... 7- 247.10.8.3 Removing Cleaning Blade.................................................................................................................................................... 7- 247.10.8.4 Mounting Cleaning Blade .................................................................................................................................................... 7- 25
7.10.9 Side Seal .............................................................................................................................................................7- 257.10.9.1 Before Removing Side Seal ................................................................................................................................................ 7- 257.10.9.2 Removing Side Seal ............................................................................................................................................................ 7- 26
7.10.10 Cleaner Scraper................................................................................................................................................. 7- 267.10.10.1 Before Cleaning Cleaner Scraper ..................................................................................................................................... 7- 267.10.10.2 Cleaning Cleaner Scraper .................................................................................................................................................. 7- 26
7.10.11 Hopper Assembly...............................................................................................................................................7- 267.10.11.1 Before Removing Hopper Assembly ................................................................................................................................. 7- 267.10.11.2 Removing Hopper Assembly ............................................................................................................................................. 7- 26
7.10.12 Hopper Supply Motor .........................................................................................................................................7- 277.10.12.1 Before Removing Toner Supply Motor .............................................................................................................................. 7- 277.10.12.2 Removing Toner Supply Motor .......................................................................................................................................... 7- 27
7.10.13 Hopper Strring Motor .........................................................................................................................................7- 277.10.13.1 Before Removing Hopper Stirring Motor ........................................................................................................................... 7- 277.10.13.2 Removing Hopper Stirring Motor ....................................................................................................................................... 7- 27
7.10.14 Developing Assembly ........................................................................................................................................7- 287.10.14.1 Removing Developing Assembly ....................................................................................................................................... 7- 287.10.14.2 Cleaning Developing Toner Blocking Sheet ...................................................................................................................... 7- 28
7.10.15 Developing Cylinder...........................................................................................................................................7- 297.10.15.1 Before Removing Developing Cylinder ............................................................................................................................. 7- 297.10.15.2 Removing Developing Cylinder ......................................................................................................................................... 7- 29
7.10.16 Developing Blade...............................................................................................................................................7- 297.10.16.1 Before Removing Developing Blade ................................................................................................................................. 7- 297.10.16.2 Removing Developing Blade ............................................................................................................................................. 7- 297.10.16.3 Mounting Developing Blade ............................................................................................................................................... 7- 29
7.10.17 Transfer/Separation Charging Assembly ...........................................................................................................7- 307.10.17.1 Removing Transfer/Separation Charging Assembly ......................................................................................................... 7- 307.10.17.2 Mounting Transfer/Separation Charging Assembly ........................................................................................................... 7- 30
7.10.18 Separation Claw/Separation Claw Drive Assembly ...........................................................................................7- 307.10.18.1 Before Removing Separation Claw Holder ........................................................................................................................ 7- 307.10.18.2 Removing Separation Claw Holder ................................................................................................................................... 7- 30
Contents
7.10.19 Potential Sensor Unit..........................................................................................................................................7- 317.10.19.1 Outline ................................................................................................................................................................................ 7- 317.10.19.2 Before Removing Potential Sensor Unit ............................................................................................................................ 7- 317.10.19.3 Removing Potential Sensor Unit ....................................................................................................................................... 7- 31
7.10.20 Charging Wire ....................................................................................................................................................7- 317.10.20.1 Outline ................................................................................................................................................................................ 7- 317.10.20.2 Routing Charging Wire ...................................................................................................................................................... 7- 317.10.20.3 Routing Grid for Primary Charging Assembly ................................................................................................................... 7- 327.10.20.4 Adjusting Height of Charging Wire .................................................................................................................................... 7- 32
Chapter 8 Pickup/Feeding System
8.1 Construction ............................................................................................................................................... 8- 18.1.1 Specifications and construction ...............................................................................................................................8- 18.1.2 Arrangement of Rollers and Sensors.......................................................................................................................8- 18.1.3 Outline of the Pickup Control System ......................................................................................................................8- 38.1.4 Outline of the Pickup Assembly Motor Control System ...........................................................................................8- 5
8.2 Basic Sequence ......................................................................................................................................... 8- 68.2.1 Pickup from the Right Deck .....................................................................................................................................8- 68.2.2 Pickup from the Cassette 3......................................................................................................................................8- 78.2.3 Pickup Retry Operation............................................................................................................................................8- 8
8.3 Detecting Jams........................................................................................................................................... 8- 88.3.1 Jam Detection Outline..............................................................................................................................................8- 8
8.3.1.1 Outline...................................................................................................................................................................................... 8- 88.3.1.2 Jam History ............................................................................................................................................................................ 8- 10
8.3.2 Delay Jams ............................................................................................................................................................8- 108.3.2.1 Cassette Pickup Assembly (right deck, left deck, cassette 3/4)............................................................................................. 8- 108.3.2.2 Other Delay Jam .................................................................................................................................................................... 8- 10
8.3.3 Stationary Jams .....................................................................................................................................................8- 118.3.3.1 Common Delay Jams............................................................................................................................................................. 8- 118.3.3.2 Power-On Stationary Jam...................................................................................................................................................... 8- 12
8.4 Cassette Pick-Up Unit .............................................................................................................................. 8- 128.4.1 Lifter Operation (cassette 3/4) ...............................................................................................................................8- 128.4.2 Detecting the Presence/Absence of Paper ............................................................................................................8- 138.4.3 Outline of the Paper Level Detection Mechanism..................................................................................................8- 148.4.4 Paper Level Detection (cassette 3/4).....................................................................................................................8- 148.4.5 Identifying the Size of Paper (cassette 3/4) ...........................................................................................................8- 148.4.6 Markings on the Width Guide Rail .........................................................................................................................8- 158.4.7 Paper Size .............................................................................................................................................................8- 15
8.5 Manual Feed Pickup Unit ......................................................................................................................... 8- 178.5.1 Pickup Operation ...................................................................................................................................................8- 178.5.2 Detecting the Size of Paper in the Manual Feed Tray ...........................................................................................8- 18
8.6 Deck ......................................................................................................................................................... 8- 198.6.1 Lifter Operation (right/left deck) .............................................................................................................................8- 198.6.2 Lifter Limiter (right/left deck) Control Circuit...........................................................................................................8- 198.6.3 Detecting the Presence/Absence of Paper ............................................................................................................8- 208.6.4 Outline of Paper Level Detection ...........................................................................................................................8- 208.6.5 Paper Level Detection Operation (right/left deck) ..................................................................................................8- 218.6.6 Identifying the Size of Paper (right/left deck) .........................................................................................................8- 21
8.7 Registration Unit ....................................................................................................................................... 8- 218.7.1 Outline....................................................................................................................................................................8- 218.7.2 Control System ......................................................................................................................................................8- 22
8.8 Duplex Feeding Unit ................................................................................................................................. 8- 228.8.1 Moving the Paper to the Reversing Assembly After Printing on the 1st Side ........................................................8- 228.8.2 Moving the Paper to the Duplexing Feed Assembly From the Reversing Assembly.............................................8- 228.8.3 Outline....................................................................................................................................................................8- 238.8.4 Sequence of Printing Operation.............................................................................................................................8- 23
Contents
8.8.5 Outline of Through-Path Operation .......................................................................................................................8- 248.8.6 Through-Path Operation........................................................................................................................................8- 248.8.7 Outline of Horizontal Registration Position ............................................................................................................8- 288.8.8 Horizontal Registration Position Detection Operation ...........................................................................................8- 28
8.9 Delivery.....................................................................................................................................................8- 298.9.1 Reversal Delivery Operation..................................................................................................................................8- 29
8.10 Parts Replacement Procedure................................................................................................................8- 318.10.1 Pickup Roller........................................................................................................................................................8- 31
8.10.1.1 Before Removing the Pickup Roller ..................................................................................................................................... 8- 318.10.1.2 Removing the Pickup Roller................................................................................................................................................. 8- 318.10.1.3 Points to Note When Mounting the Pickup Roller ................................................................................................................ 8- 31
8.10.2 Cassette Pickup Assembly ..................................................................................................................................8- 318.10.2.1 Removing the Cassette 3/4 Pickup Assembly ..................................................................................................................... 8- 31
8.10.3 Cassette Pickup Motor.........................................................................................................................................8- 318.10.3.1 Before Removing the Cassette 3/4 Pickup Motor ................................................................................................................ 8- 318.10.3.2 Removing the Cassette 3/4 Pickup Motor............................................................................................................................ 8- 31
8.10.4 Cassette Lifter Motor ...........................................................................................................................................8- 328.10.4.1 Removing the Cassette 3 Lifter Motor M20.......................................................................................................................... 8- 328.10.4.2 Removing the Cassette 4 Lifter Motor M21.......................................................................................................................... 8- 328.10.4.3 Adjusting the Position of the Lifter Motor M20/M21 of the Cassette 3/4 .............................................................................. 8- 33
8.10.5 Left Deck Lifter Motor ..........................................................................................................................................8- 338.10.5.1 Before Removing the Left Deck Lifter Motor ........................................................................................................................ 8- 338.10.5.2 Removing the Left Deck Lifter Motor.................................................................................................................................... 8- 33
8.10.6 Right Deck Lifter Motor ........................................................................................................................................8- 348.10.6.1 Before Removing the Right Deck Lifter Motor...................................................................................................................... 8- 348.10.6.2 Removing the Right Deck Lifter Motor ................................................................................................................................. 8- 34
8.10.7 Right Deck Pickup Assembly...............................................................................................................................8- 358.10.7.1 Removing the Right Deck Pickup Assembly ........................................................................................................................ 8- 35
8.10.8 Left Deck Pickup Assembly .................................................................................................................................8- 358.10.8.1 Removing the Left Deck Pickup Assembly .......................................................................................................................... 8- 35
8.10.9 Left Deck Pickup Motor........................................................................................................................................8- 368.10.9.1 Before Removing the Left Deck Pickup Motor ..................................................................................................................... 8- 368.10.9.2 Removing the Left Deck Pickup Motor................................................................................................................................. 8- 36
8.10.10 Right Deck Pickup Motor ...................................................................................................................................8- 368.10.10.1 Before Removing the Right Deck Pickup Motor ................................................................................................................. 8- 368.10.10.2 Removing the Right Deck Pickup Motor............................................................................................................................. 8- 36
8.10.11 Left Deck Pickup Sensor....................................................................................................................................8- 368.10.11.1 Before Removing the Left Deck Feeding Sensor ............................................................................................................... 8- 368.10.11.2 Removing the Left Deck Feeding Sensor........................................................................................................................... 8- 36
8.10.12 Left Deck Pickup Solenoid .................................................................................................................................8- 368.10.12.1 Before Removing the Left Deck Pickup Solenoid............................................................................................................... 8- 368.10.12.2 Removing the Left Deck Pickup Solenoid .......................................................................................................................... 8- 378.10.12.3 Adjusting the Position of the Left Deck Pickup Solenoid.................................................................................................... 8- 37
8.10.13 Manual Feed Pull-Out Roller Unit ......................................................................................................................8- 378.10.13.1 Removing the Manual Feeding Pickup Roller Unit ............................................................................................................. 8- 37
8.10.14 Manual Feed Pull-Out Roller..............................................................................................................................8- 378.10.14.1 Before Removing the Manual Feeding Pickup Roller......................................................................................................... 8- 378.10.14.2 Removing the Manual Feeding Pickup Roller .................................................................................................................... 8- 37
8.10.15 Manual Feed Roller............................................................................................................................................8- 388.10.15.1 Before Removing the Manual Feeding Roller .................................................................................................................... 8- 388.10.15.2 Removing the Manual Feeding Roller ................................................................................................................................ 8- 38
8.10.16 Manual Separation Roller ..................................................................................................................................8- 388.10.16.1 Before Removing the Manual Separation Roller ................................................................................................................ 8- 388.10.16.2 Removing the Manual Separation Roller............................................................................................................................ 8- 388.10.16.3 Adjusting the Pressure of the Manual Separation Roller.................................................................................................... 8- 38
8.10.17 Manual Feed Tray paper sensor........................................................................................................................8- 398.10.17.1 Removing the Manual Feeding Tray Sensor...................................................................................................................... 8- 39
8.10.18 Registration Roller .............................................................................................................................................8- 398.10.18.1 Before Removing the Registration Roller ........................................................................................................................... 8- 39
Contents
8.10.18.2 Removing the Registration Roller....................................................................................................................................... 8- 398.10.19 Pre-Registration Roller .......................................................................................................................................8- 40
8.10.19.1 Before Removing the Registration Lower Roller ................................................................................................................ 8- 408.10.19.2 Removing the Registration Lower Roller............................................................................................................................ 8- 40
8.10.20 Pre-Registration Motor .......................................................................................................................................8- 418.10.20.1 Before Removing the Registration Front Motor.................................................................................................................. 8- 418.10.20.2 Removing the Registration Front Motor ............................................................................................................................. 8- 41
8.10.21 Registration Motor ..............................................................................................................................................8- 418.10.21.1 Before Removing the Horizontal Registration Motor .......................................................................................................... 8- 418.10.21.2 Removing the Horizontal Registration Motor...................................................................................................................... 8- 41
8.10.22 Registration Sensor............................................................................................................................................8- 428.10.22.1 Before Removing the Horizontal Registration Sensor........................................................................................................ 8- 428.10.22.2 Removing the Horizontal Registration Sensor ................................................................................................................... 8- 42
8.10.23 Registration Clutch .............................................................................................................................................8- 438.10.23.1 Before Removing the Registration Clutch .......................................................................................................................... 8- 438.10.23.2 Removing the Registration Clutch...................................................................................................................................... 8- 43
8.10.24 Registration Brake Clutch...................................................................................................................................8- 438.10.24.1 Before Removing the Registration Brake ........................................................................................................................... 8- 438.10.24.2 Removing the Registration Brake....................................................................................................................................... 8- 43
8.10.25 Feeding Roller ....................................................................................................................................................8- 438.10.25.1 Before Removing the Feeding Roller ................................................................................................................................. 8- 438.10.25.2 Removing the Feeding Roller............................................................................................................................................. 8- 438.10.25.3 The Points to Mount the Feeding Roller............................................................................................................................. 8- 44
8.10.26 Vertical Path Roller.............................................................................................................................................8- 448.10.26.1 Before Removing the Vertical Path Roller.......................................................................................................................... 8- 448.10.26.2 Removing the Vertical Path Roller ..................................................................................................................................... 8- 448.10.26.3 Removing the Vertical Path Roller 2/3 ............................................................................................................................... 8- 44
8.10.27 Vertical Path Motor.............................................................................................................................................8- 448.10.27.1 Before Removing the Vertical Path Upper Motor ............................................................................................................... 8- 448.10.27.2 Removing the Vertical Path Upper Motor........................................................................................................................... 8- 45
8.10.28 Vertical Path Duplex Motor.................................................................................................................................8- 458.10.28.1 Before Removing the Vertical Path Duplex Motor.............................................................................................................. 8- 458.10.28.2 Removing the Vertical Path Duplex Motor ......................................................................................................................... 8- 45
8.10.29 Vertical Path Lower Motor ..................................................................................................................................8- 458.10.29.1 Before Removing the Vertical Path Lower Motor ............................................................................................................... 8- 458.10.29.2 Removing the Vertical Path Lower Motor........................................................................................................................... 8- 45
8.10.30 Reversing Motor .................................................................................................................................................8- 458.10.30.1 Before Removing the Reversing Motor .............................................................................................................................. 8- 458.10.30.2 Removing the Reversing Motor.......................................................................................................................................... 8- 468.10.30.3 Mounting the Reversing Motor ........................................................................................................................................... 8- 46
8.10.31 Fixing Feeding Unit Releasing Lever Sensor .....................................................................................................8- 468.10.31.1 Before Removing the Fixing Feeding Unit Release Lever Sensor ..................................................................................... 8- 468.10.31.2 Removing the Fixing Feeding Unit Release Lever Sensor................................................................................................. 8- 46
8.10.32 Reversing Sensor...............................................................................................................................................8- 468.10.32.1 Before Removing the Reversing Sensor 1 ......................................................................................................................... 8- 468.10.32.2 Removing the Reversing Sensor 1..................................................................................................................................... 8- 468.10.32.3 Before Removing the Reversing Sensor 2 ......................................................................................................................... 8- 478.10.32.4 Removing the Reversing Sensor 2..................................................................................................................................... 8- 47
8.10.33 Reversing Unit....................................................................................................................................................8- 478.10.33.1 Before Removing the Reversing Flapper Solenoid ............................................................................................................ 8- 478.10.33.2 Removing the Reversing Flapper Solenoid........................................................................................................................ 8- 478.10.33.3 Mounting the Reversing Flapper Solenoid ......................................................................................................................... 8- 47
8.10.34 Feeding Belt .......................................................................................................................................................8- 488.10.34.1 Before Removing the feeding belt ..................................................................................................................................... 8- 488.10.34.2 Removing the feeding belt ................................................................................................................................................. 8- 48
8.10.35 Duplexing Unit ....................................................................................................................................................8- 498.10.35.1 Before Removing the Duplex Feeding Unit ........................................................................................................................ 8- 498.10.35.2 Removing the Duplex Feeding Unit.................................................................................................................................... 8- 49
8.10.36 Duplex Feed Motor.............................................................................................................................................8- 498.10.36.1 Before Removing the Duplex Feeding Left Motor .............................................................................................................. 8- 49
Contents
8.10.36.2 Removing the Duplex Feeding Left Motor.......................................................................................................................... 8- 498.10.36.3 Before Removing the Duplex Feeding Right Motor............................................................................................................ 8- 498.10.36.4 Removing the Duplex Feeding Right Motor ....................................................................................................................... 8- 49
8.10.37 Duplex Feed Sensor ..........................................................................................................................................8- 498.10.37.1 Before Removing the Duplex Pre-Registration Sensor ...................................................................................................... 8- 498.10.37.2 Removing the Duplex Pre-Registration Sensor.................................................................................................................. 8- 49
8.10.38 Separation Roller ...............................................................................................................................................8- 508.10.38.1 Before Removing the Separation Roller............................................................................................................................. 8- 508.10.38.2 Removing the Separation Roller ........................................................................................................................................ 8- 508.10.38.3 Points to Note When Mounting the Separation Roller........................................................................................................ 8- 508.10.38.4 Adjusting the Pressure of the Deck/Cassette Separation Roller ........................................................................................ 8- 51
Chapter 9 Fixing System
9.1 Construction ...............................................................................................................................................9- 19.1.1 Specifications, Control Mechanisms, and Functions ...............................................................................................9- 19.1.2 Major Components ..................................................................................................................................................9- 19.1.3 IH Fixing Method (outline) .......................................................................................................................................9- 39.1.4 Limiting th Rise in Temperature at the Roller Edges by Use of a Flux blocking Plate (shutter) ..............................9- 3
9.2 Basic Sequence..........................................................................................................................................9- 49.2.1 Outline .....................................................................................................................................................................9- 49.2.2 30-Sec Start-Up Mode.............................................................................................................................................9- 49.2.3 Low-Temperature Environment Start-Up Mode....................................................................................................... 9- 59.2.4 High-Humidity Environment Start-Up Mode ............................................................................................................9- 59.2.5 Recovery Mode .......................................................................................................................................................9- 69.2.6 Standby Mode .........................................................................................................................................................9- 69.2.7 Power Save Mode ................................................................................................................................................... 9- 79.2.8 Sleep Mode ............................................................................................................................................................9- 79.2.9 Copying/Printing Mode ............................................................................................................................................9- 79.2.10 Down Sequence ....................................................................................................................................................9- 89.2.11 Enhanced Fixing Mode ..........................................................................................................................................9- 89.2.12 Heavy Paper Mode ................................................................................................................................................ 9- 99.2.13 Transparency Mode...............................................................................................................................................9- 99.2.14 Bond Paper Mode..................................................................................................................................................9- 9
9.3 Various Control Mechanisms....................................................................................................................9- 109.3.1 Fixing Drive System...............................................................................................................................................9- 10
9.3.1.1 Controlling the Drive of the Fixing Roller ............................................................................................................................... 9- 109.3.1.2 Controlling the Drive of the Fixing Inlet Guide ....................................................................................................................... 9- 109.3.1.3 Controlling the Reciprocating Movement of the Thermistor................................................................................................... 9- 119.3.1.4 Controlling the Reciprocating Mechanism of the Upper Separation Claw ............................................................................. 9- 119.3.1.5 Controlling the Drive of the Shutter........................................................................................................................................ 9- 129.3.1.6 Controlling the Shutter Position ............................................................................................................................................. 9- 13
9.3.2 Cleaning ................................................................................................................................................................9- 149.3.2.1 Controlling the Drive of the Cleaning Web............................................................................................................................. 9- 149.3.2.2 Controlling the Mechanism Used to Detect the Remaining Length of the Cleaning Web...................................................... 9- 15
9.3.3 Detecting the Passage of Paper............................................................................................................................9- 169.3.3.1 Preventing Wrapping of Paper............................................................................................................................................... 9- 16
9.4 Protective Functions .................................................................................................................................9- 179.4.1 Detecting an Error Using the Thermistor ...............................................................................................................9- 179.4.2 Detecting an Error Using the Thermal Switch .......................................................................................................9- 179.4.3 Errors.....................................................................................................................................................................9- 17
9.5 Parts Replacement Procedure .................................................................................................................9- 199.5.1 Fixing/Feeding Assembly ......................................................................................................................................9- 19
9.5.1.1 Before Removing the Fixing/Feeding unit .............................................................................................................................. 9- 199.5.1.2 Removing the Fixing/Feeding unit ......................................................................................................................................... 9- 19
9.5.2 Fixing Unit..............................................................................................................................................................9- 209.5.2.1 Before Removing the Fixing Upper Unit ................................................................................................................................ 9- 209.5.2.2 Removing the Fixing Upper Unit ............................................................................................................................................ 9- 20
Contents
9.5.3 Pressure Roller ......................................................................................................................................................9- 209.5.3.1 Before Removing the Pressure Roller ................................................................................................................................... 9- 209.5.3.2 Removing the Pressure Roller ............................................................................................................................................... 9- 20
9.5.4 Upper Fixing Roller ................................................................................................................................................9- 219.5.4.1 Before Removing the Fixing Roller ........................................................................................................................................ 9- 219.5.4.2 Removing the Fixing Roller.................................................................................................................................................... 9- 219.5.4.3 Points to Note When Mounting the Fixing Roller ................................................................................................................... 9- 239.5.4.4 Applying Grease After Replacing the Fixing Roller................................................................................................................ 9- 249.5.4.5 Adjusting the Nip Width.......................................................................................................................................................... 9- 25
9.5.5 External Delivery Roller .........................................................................................................................................9- 259.5.5.1 Before Removing the External Delivery Roller....................................................................................................................... 9- 259.5.5.2 Removing the External Delivery Roller .................................................................................................................................. 9- 25
9.5.6 Internal Delivery Roller...........................................................................................................................................9- 269.5.6.1 Before Removing the Internal Delivery Roller........................................................................................................................ 9- 269.5.6.2 Removing the Internal Delivery Roller ................................................................................................................................... 9- 269.5.6.3 Points to Note When Mounting the Internal Delivery Roller................................................................................................... 9- 27
9.5.7 Main Thermistor .....................................................................................................................................................9- 279.5.7.1 Before Removing the Main Thermistor/Shutter Thermistor ................................................................................................... 9- 279.5.7.2 Removing the Main Thermistor/Shutter Thermistor ............................................................................................................... 9- 279.5.7.3 Points to Note When Mounting the Main Thermistor/Shutter Thermistor .............................................................................. 9- 28
9.5.8 Sub Thermistor ......................................................................................................................................................9- 289.5.8.1 Before Removing the Sub Thermistor.................................................................................................................................... 9- 289.5.8.2 Removing the Sub Thermistor ............................................................................................................................................... 9- 299.5.8.3 Points to Note When Mounting the Sub Thermistor............................................................................................................... 9- 29
9.5.9 Thermal Switch ......................................................................................................................................................9- 299.5.9.1 Before Removing the Thermal Switch ................................................................................................................................... 9- 299.5.9.2 Removing the Thermal Switch ............................................................................................................................................... 9- 30
9.5.10 Fixing Heater........................................................................................................................................................9- 309.5.10.1 Before Removing the Fixing Heater Unit.............................................................................................................................. 9- 309.5.10.2 Removing the Fixing Heater Unit ......................................................................................................................................... 9- 30
9.5.11 Fixing Cleaning Belt .............................................................................................................................................9- 329.5.11.1 Before Removing the Fixing Web ........................................................................................................................................ 9- 329.5.11.2 Removing the Fixing Web .................................................................................................................................................... 9- 329.5.11.3 Cleaning the fixing oil dish and the fixing cleaning belt guide .............................................................................................. 9- 329.5.11.4 Mounting the Fixing Web ..................................................................................................................................................... 9- 329.5.11.5 After Replacing the Fixing Web............................................................................................................................................ 9- 33
9.5.12 Fixing Jam Sensor ...............................................................................................................................................9- 339.5.12.1 Before Removing the Delivery Jam Sensor ......................................................................................................................... 9- 339.5.12.2 Removing the Delivery Jam Sensor..................................................................................................................................... 9- 33
9.5.13 Claw Jam Sensor .................................................................................................................................................9- 339.5.13.1 Before Removing the Claw Jam Sensor .............................................................................................................................. 9- 339.5.13.2 Removing the Claw Jam Sensor.......................................................................................................................................... 9- 33
9.5.14 External Delivery Sensor......................................................................................................................................9- 349.5.14.1 Before Removing the External Delivery Sensor................................................................................................................... 9- 349.5.14.2 Removing the External Delivery Sensor .............................................................................................................................. 9- 34
9.5.15 Internal Delivery Sensor.......................................................................................................................................9- 349.5.15.1 Before Removing the Internal Delivery Sensor .................................................................................................................... 9- 349.5.15.2 Removing the Internal Delivery Sensor................................................................................................................................ 9- 34
9.5.16 Fixing Inlet Sensor ...............................................................................................................................................9- 349.5.16.1 Before Removing the Fixing Inlet Sensor............................................................................................................................. 9- 349.5.16.2 Removing the Fixing Inlet Sensor ........................................................................................................................................ 9- 349.5.16.3 Adjusting the Fixing Inlet Guide ........................................................................................................................................... 9- 35
9.5.17 Fixing web sensor ................................................................................................................................................9- 359.5.17.1 Before Removing the Fixing Web Sensor ............................................................................................................................ 9- 359.5.17.2 Removing the Fixing Web Sensor........................................................................................................................................ 9- 35
9.5.18 Fixing shutter sensor............................................................................................................................................9- 359.5.18.1 Before Removing the Shutter Sensor .................................................................................................................................. 9- 359.5.18.2 Removing the Shutter Sensor .............................................................................................................................................. 9- 35
9.5.19 Fixing shutter motor .............................................................................................................................................9- 359.5.19.1 Before Removing the Shutter Motor..................................................................................................................................... 9- 35
Contents
9.5.19.2 Removing the Shutter Motor ................................................................................................................................................ 9- 359.5.20 Fixing Inlet Guide Solenoid..................................................................................................................................9- 36
9.5.20.1 Before Removing the Fixing Inlet Guide Solenoid (SL1)...................................................................................................... 9- 369.5.20.2 Removing the Fixing Inlet Guide Solenoid (SL1) ................................................................................................................. 9- 369.5.20.3 Adjusting the Fixing Inlet Guide Solenoid (SL1)................................................................................................................... 9- 36
9.5.21 Delivery Flapper Solenoid....................................................................................................................................9- 369.5.21.1 Before Removing the Delivery Flapper Solenoid (SL5) ....................................................................................................... 9- 369.5.21.2 Removing the Delivery Flapper Solenoid (SL5) ................................................................................................................... 9- 369.5.21.3 Points to Note When Mounting the Delivery Flapper Solenoid (SL5) .................................................................................. 9- 37
9.5.22 Fixing Cleaning Web Solenoid.............................................................................................................................9- 379.5.22.1 Before Removing the Fixing Web Solenoid (SL9)................................................................................................................ 9- 379.5.22.2 Removing the Fixing Web Solenoid (SL9) ........................................................................................................................... 9- 379.5.22.3 Adjusting the Fixing Web Solenoid (SL9)............................................................................................................................. 9- 37
9.5.23 Upper Separation Claw........................................................................................................................................9- 379.5.23.1 Removing the Upper Separation Claw................................................................................................................................. 9- 379.5.23.2 Points to Note When Mounting the Upper Separation Claw ................................................................................................ 9- 38
9.5.24 Lower Separation Claw........................................................................................................................................9- 389.5.24.1 Before Removing the Lower Separation Claw (Unit) ........................................................................................................... 9- 389.5.24.2 Removing the Lower Separation Claw (Unit) ....................................................................................................................... 9- 39
Chapter 10 External and Controls
10.1 Control Panel ..........................................................................................................................................10- 110.1.1 Overview..............................................................................................................................................................10- 110.1.2 LCD Indication Processing ..................................................................................................................................10- 110.1.3 Adjusting the LCD Contrast .................................................................................................................................10- 110.1.4 Functions of the Control Panel CPU....................................................................................................................10- 1
10.2 Counters .................................................................................................................................................10- 110.2.1 Soft Counters.......................................................................................................................................................10- 1
10.3 Fans........................................................................................................................................................10- 310.3.1 Arrangement, Functions, and Error Codes ..........................................................................................................10- 310.3.2 Controlling the Speed of the Fans .......................................................................................................................10- 410.3.3 Sequence of Operation........................................................................................................................................10- 4
10.4 Power Supply System.............................................................................................................................10- 510.4.1 Power Supply.......................................................................................................................................................10- 5
10.4.1.1 Overview .............................................................................................................................................................................. 10- 510.4.1.2 Distribution of Power and the Switches................................................................................................................................ 10- 5
10.4.2 Rated Output of the DC Power Supply PCB........................................................................................................10- 710.4.2.1 Rated Output of the DC Power Supply PCB ........................................................................................................................ 10- 710.4.2.2 Rated Output of the Accessories Power Supply PCB.......................................................................................................... 10- 7
10.4.3 Protection Function.............................................................................................................................................. 10- 810.4.3.1 Protective Functions............................................................................................................................................................. 10- 8
10.4.4 Backup Battery ....................................................................................................................................................10- 810.4.4.1 Backup Battery..................................................................................................................................................................... 10- 8
10.4.5 Energy-Saving Function ......................................................................................................................................10- 810.4.5.1 Overview .............................................................................................................................................................................. 10- 810.4.5.2 SNMP setup ......................................................................................................................................................................... 10- 9
10.5 Parts Replacement Procedure..............................................................................................................10- 1210.5.1 External Covers .................................................................................................................................................10- 12
10.5.1.1 Right Cover (Lower Rear) .................................................................................................................................................. 10- 1210.5.1.2 Right Cover (Upper Rear) .................................................................................................................................................. 10- 1210.5.1.3 Right Cover (Upper) ........................................................................................................................................................... 10- 1210.5.1.4 Left Cover (Upper) ............................................................................................................................................................. 10- 1210.5.1.5 Front Cover ........................................................................................................................................................................ 10- 1310.5.1.6 Rear Cover (Upper)............................................................................................................................................................ 10- 1310.5.1.7 Rear Cover (Lower)............................................................................................................................................................ 10- 1310.5.1.8 Left Cover (Lower) ............................................................................................................................................................. 10- 1310.5.1.9 Left Cover (Middle)............................................................................................................................................................. 10- 1410.5.1.10 Toner Supply Cover ......................................................................................................................................................... 10- 14
Contents
10.5.1.11 Fixing/Feeding Unit Cover................................................................................................................................................ 10- 1410.5.1.12 Fixing Cover (Upper) ........................................................................................................................................................ 10- 1510.5.1.13 Fixing Cover (Lower) ........................................................................................................................................................ 10- 1610.5.1.14 Main Controller Box Cover ............................................................................................................................................... 10- 1710.5.1.15 Reader Left Cover ............................................................................................................................................................ 10- 1710.5.1.16 Reader Right Cover.......................................................................................................................................................... 10- 1710.5.1.17 Reader Front Cover.......................................................................................................................................................... 10- 1710.5.1.18 Reader Rear Cover .......................................................................................................................................................... 10- 18
10.5.2 Left Deck Drive Assembly ..................................................................................................................................10- 1910.5.2.1 Before Removing the Left Deck Drive Assembly ............................................................................................................... 10- 1910.5.2.2 Removing the Left Deck Drive Assembly........................................................................................................................... 10- 19
10.5.3 Manual Feed Pickup Drive Assembly ................................................................................................................10- 1910.5.3.1 Before Removing the Manual Pickup Drive Assembly....................................................................................................... 10- 1910.5.3.2 Removing the Manual Pickup Drive Assembly .................................................................................................................. 10- 19
10.5.4 Vertical Path Drive Assembly.............................................................................................................................10- 1910.5.4.1 Before Removing the Vertical Path Drive Assembly .......................................................................................................... 10- 1910.5.4.2 Removing the Vertical Path Drive Assembly...................................................................................................................... 10- 19
10.5.5 Waste Toner Drive Assembly.............................................................................................................................10- 2010.5.5.1 Before Removing the Collecting Toner Drive Assembly .................................................................................................... 10- 2010.5.5.2 Removing the Collecting Toner Drive Assembly................................................................................................................ 10- 20
10.5.6 Main Drive Assembly .........................................................................................................................................10- 2110.5.6.1 Fitting the Drive Belt........................................................................................................................................................... 10- 21
10.5.7 Cassette Pickup Drive Assembly .......................................................................................................................10- 2110.5.7.1 Before Removing the Cassette Pickup Drive Assembly .................................................................................................... 10- 2110.5.7.2 Removing the Cassette Pickup Drive Assembly ................................................................................................................ 10- 21
10.5.8 Fixing Drive Assembly........................................................................................................................................10- 2210.5.8.1 Before Removing the Fixing Drive Assembly..................................................................................................................... 10- 2210.5.8.2 Removing the Fixing Drive Assembly ................................................................................................................................ 10- 22
10.5.9 Power Supply Unit..............................................................................................................................................10- 2210.5.9.1 Removing the Charger unit ................................................................................................................................................ 10- 2210.5.9.2 Points to Note At Occurrence of Charger unit Malfunction ................................................................................................ 10- 22
10.5.10 Duplex Unit PCB ..............................................................................................................................................10- 2310.5.10.1 Before Removing the Duplex unit PCB ............................................................................................................................ 10- 2310.5.10.2 Removing the Duplex Unit PCB ....................................................................................................................................... 10- 23
10.5.11 Control Panel....................................................................................................................................................10- 2310.5.11.1 Before Removing Control Panel ...................................................................................................................................... 10- 2310.5.11.2 Removing Control Panel ................................................................................................................................................. 10- 23
10.5.12 DC Controller PCB ...........................................................................................................................................10- 2410.5.12.1 Before Removing DC Controller PCB ............................................................................................................................. 10- 2410.5.12.2 Removing DC Controller PCB ......................................................................................................................................... 10- 2410.5.12.3 When Replacing DC Controller PCB ............................................................................................................................... 10- 24
10.5.13 Printer Power Supply PCB ...............................................................................................................................10- 2410.5.13.1 Before Removing Printer Power Supply PCB ................................................................................................................. 10- 2410.5.13.2 Removing Printer Power Supply PCB ............................................................................................................................. 10- 24
10.5.14 Option Power Supply PCB ...............................................................................................................................10- 2510.5.14.1 Before Removing Accessories Power Supply PCB ......................................................................................................... 10- 2510.5.14.2 Removing Accessories Power Supply PCB .................................................................................................................... 10- 25
10.5.15 Fixing Heater Power Supply PCB ....................................................................................................................10- 2510.5.15.1 Before Removing Fixing Heater Power Supply PCB ....................................................................................................... 10- 2510.5.15.2 Removing Fixing Heater Power Supply PCB .................................................................................................................. 10- 25
10.5.16 Anti-Rush Current PCB ....................................................................................................................................10- 2610.5.16.1 Before Removing Anti-Rush Current PCB ...................................................................................................................... 10- 2610.5.16.2 Removing Anti-Rush Current PCB .................................................................................................................................. 10- 26
10.5.17 High-Voltage Transformer (AC)........................................................................................................................10- 2710.5.17.1 Before Removing High Voltage Transformer .................................................................................................................. 10- 2710.5.17.2 Removing High Voltage Transformer .............................................................................................................................. 10- 2710.5.17.3 Removing High Voltage Transformer ............................................................................................................................... 10- 27
10.5.18 HVT PCB..........................................................................................................................................................10- 2810.5.18.1 Before Removing HVT PCB ............................................................................................................................................ 10- 2810.5.18.2 Removing HVT PCB ........................................................................................................................................................ 10- 28
Contents
10.5.18.3 When Replacing HVT PCB ............................................................................................................................................. 10- 2810.5.19 Separation Clew AC bias PCB.........................................................................................................................10- 28
10.5.19.1 Before Removing Separation Claw AC PCB ................................................................................................................... 10- 2810.5.19.2 Removing Separation Claw AC PCB .............................................................................................................................. 10- 28
10.5.20 Motor Driver PCB.............................................................................................................................................10- 2810.5.20.1 Before Removing Motor Driver PCB ............................................................................................................................... 10- 2810.5.20.2 Removing Motor Driver PCB ........................................................................................................................................... 10- 28
10.5.21 Primary Fan Duct ............................................................................................................................................ 10- 2810.5.21.1 Before Removing Primary fan Duct ................................................................................................................................. 10- 2810.5.21.2 Removing Primary fan Duct ............................................................................................................................................ 10- 29
10.5.22 Primary Charging Assembly Fan .....................................................................................................................10- 2910.5.22.1 Before Removing Primary Charging Fan ........................................................................................................................ 10- 2910.5.22.2 Removing the Primary Charging Cooling Fan.................................................................................................................. 10- 29
10.5.23 De-Curling Fan.................................................................................................................................................10- 2910.5.23.1 Before Removing the Curl-Removing Fan ....................................................................................................................... 10- 2910.5.23.2 Removing the Curl-Removing Fan ................................................................................................................................... 10- 29
10.5.24 Feeding Fan.....................................................................................................................................................10- 2910.5.24.1 Before Removing the Feeding Fan .................................................................................................................................. 10- 2910.5.24.2 Removing the Feeding Fan .............................................................................................................................................. 10- 30
10.5.25 HVT Fan...........................................................................................................................................................10- 3010.5.25.1 Before Removing the HVT Fan ........................................................................................................................................ 10- 3010.5.25.2 Removing the HVT Fan.................................................................................................................................................... 10- 30
10.5.26 Duplex Feed Fan .............................................................................................................................................10- 3010.5.26.1 Before Removing the Duplex Feeding Fan ...................................................................................................................... 10- 3010.5.26.2 Removing the Duplex Feeding Fan.................................................................................................................................. 10- 30
10.5.27 Exhaust Fan.....................................................................................................................................................10- 3110.5.27.1 Before Removing the Exhaust Fan .................................................................................................................................. 10- 3110.5.27.2 Removing the Exhaust Fan .............................................................................................................................................. 10- 31
10.5.28 DC Power Supply Fan .....................................................................................................................................10- 3110.5.28.1 Before Removing the DC Power Supply Fan ................................................................................................................... 10- 3110.5.28.2 Removing the DC Power Supply Fan............................................................................................................................... 10- 31
10.5.29 Fixing Heater Power Supply Cooling Fan ........................................................................................................10- 3210.5.29.1 Before Removing the Fixing Heater Power Supply Cooling Fan...................................................................................... 10- 3210.5.29.2 Removing the Fixing Heater Power Supply Cooling Fan ................................................................................................. 10- 32
10.5.30 Circulation Duct Fan ........................................................................................................................................10- 3210.5.30.1 Before Removing the Circulation Duct Fan ...................................................................................................................... 10- 3210.5.30.2 Removing the Circulation Duct Fan.................................................................................................................................. 10- 32
10.5.31 Motor of Main Drive Assembly .........................................................................................................................10- 3310.5.31.1 Before Removing the Main Motor..................................................................................................................................... 10- 3310.5.31.2 Removing the Main Motor ................................................................................................................................................ 10- 33
10.5.32 Fixing Driver Motor...........................................................................................................................................10- 3310.5.32.1 Before Removing the Fixing Motor................................................................................................................................... 10- 3310.5.32.2 Removing the Fixing Motor .............................................................................................................................................. 10- 33
10.5.33 Right Door........................................................................................................................................................10- 3410.5.33.1 Before Removing the Right Door Unit (Upper)................................................................................................................. 10- 3410.5.33.2 Removing the Right Door Unit (Upper) ............................................................................................................................ 10- 34
Chapter 11 MEAP
11.1 MEAP......................................................................................................................................................11- 111.1.1 Checking the Operating Environment. .................................................................................................................11- 111.1.2 Setting Up the Network........................................................................................................................................11- 411.1.3 Setting the method to login to SMS .....................................................................................................................11- 511.1.4 Login to SMS .......................................................................................................................................................11- 911.1.5 Checking Application List...................................................................................................................................11- 1111.1.6 Starting and Stopping a MEAP Application .......................................................................................................11- 1211.1.7 Checking the Platform Information ....................................................................................................................11- 1311.1.8 MEAP Specifications .........................................................................................................................................11- 1411.1.9 Checking the System Information of a MEAP Application with SMS.................................................................11- 15
Contents
11.1.10 Printing the System Information of a MEAP Application ..................................................................................11- 1611.1.11 Reference (Application System Information)....................................................................................................11- 1711.1.12 Installing an Application....................................................................................................................................11- 1811.1.13 MEAP Enterprise Service Manager..................................................................................................................11- 2111.1.14 Adding a License File .......................................................................................................................................11- 2111.1.15 Disabling a License File (suspending a license) ..............................................................................................11- 2311.1.16 Downloading/Removing an Invalidated License File........................................................................................11- 2511.1.17 Reusable license ..............................................................................................................................................11- 2711.1.18 License for forwarding ......................................................................................................................................11- 2811.1.19 Uninstalling an Application ...............................................................................................................................11- 3011.1.20 Changing Login Services .................................................................................................................................11- 3111.1.21 Initializing the Password...................................................................................................................................11- 3511.1.22 Creating a Backup for MEAP Application Area, Formatting the Hard Disk, Restoring the MEAP Application Area
with the Backup, Using the SST (Service Support Tool)..........................................................................................11- 3611.1.23 Replacing the Hard Disk Drive .........................................................................................................................11- 3811.1.24 MEAP Safe Mode.............................................................................................................................................11- 3811.1.25 Setting HTTP port for MEAP application (level 2) ............................................................................................11- 4011.1.26 Reference material ...........................................................................................................................................11- 4311.1.27 Option for exclusive individual measure...........................................................................................................11- 47
Chapter 12 RDS
12.1 RDS ........................................................................................................................................................ 12- 112.1.1 Application operation mode..................................................................................................................................12- 112.1.2 Service Center URL and Port Specification .........................................................................................................12- 112.1.3 Communication test .............................................................................................................................................12- 112.1.4 Communication log ..............................................................................................................................................12- 112.1.5 Detailed Communication log ................................................................................................................................12- 112.1.6 SOAP communication function ............................................................................................................................12- 112.1.7 Resend at SOAP transmission error ....................................................................................................................12- 212.1.8 e-RDS setting screen ...........................................................................................................................................12- 212.1.9 Sleep operation ....................................................................................................................................................12- 512.1.10 Network Setting (Maintenance) ..........................................................................................................................12- 512.1.11 e-RDS Setting (Maintenance) ............................................................................................................................12- 512.1.12 Trouble shoot .....................................................................................................................................................12- 612.1.13 Error message....................................................................................................................................................12- 6
Chapter 13 Maintenance and Inspection
13.1 Periodically Replaced Parts.................................................................................................................... 13- 113.1.1 Outline..................................................................................................................................................................13- 113.1.2 Reader Unit ..........................................................................................................................................................13- 113.1.3 Printer Unit ...........................................................................................................................................................13- 1
13.2 Durables and Consumables ................................................................................................................... 13- 113.2.1 Outline..................................................................................................................................................................13- 113.2.2 Reader unit...........................................................................................................................................................13- 213.2.3 Printer Unit ...........................................................................................................................................................13- 2
13.3 Scheduled Servicing Basic Procedure ................................................................................................... 13- 213.3.1 Scheduled Servicing Basic Procedure .................................................................................................................13- 213.3.2 Periodical Servicing Chart Reader Unit................................................................................................................13- 313.3.3 Periodical Servicing Chart Printer Unit.................................................................................................................13- 413.3.4 Points to Note for Periodical Servicing.................................................................................................................13- 5
13.4 Cleaning ................................................................................................................................................. 13- 613.4.1 Cleaning Primary Toner Blocking Sheet .............................................................................................................13- 613.4.2 Cleaning Developing Toner Blocking Sheet ........................................................................................................13- 613.4.3 Cleaning Cleaner Scraper ...................................................................................................................................13- 6
Contents
13.4.4 Cleaning Photosensitive Drum ...........................................................................................................................13- 713.4.5 Cleaning the fixing oil dish and the fixing cleaning belt guide..............................................................................13- 8
Chapter 14 Standards and Adjustments
14.1 Image Adjustment Basic Procedure........................................................................................................14- 114.1.1 Making Pre-Checks .............................................................................................................................................14- 114.1.2 Making Checks on the Printer Unit (1/2)..............................................................................................................14- 114.1.3 Making Checks on the Printer Unit (2/2)..............................................................................................................14- 314.1.4 Making Checks on the Reader Unit .....................................................................................................................14- 414.1.5 Checking the Potential System............................................................................................................................14- 714.1.6 Checking the Surface Potential Control System..................................................................................................14- 914.1.7 Potential Control System Conversion Table ......................................................................................................14- 1114.1.8 Emergency Measures for a Fault in the Potential Sensor .................................................................................14- 16
14.2 Image Adjustments ...............................................................................................................................14- 1714.2.1 Standards of Image Position..............................................................................................................................14- 1714.2.2 Checking the Image Position .............................................................................................................................14- 1714.2.3 Adjusting Side Registration................................................................................................................................14- 1714.2.4 Adjusting the Image Leading Edge Margin........................................................................................................14- 1814.2.5 Adjusting the Left/Right Non-Image Width.........................................................................................................14- 1814.2.6 Adjusting the Leading Edge Non-Image Width..................................................................................................14- 18
14.3 Scanning System..................................................................................................................................14- 1914.3.1 After Replacing the Reader Controller PCB ......................................................................................................14- 1914.3.2 When Replacing the CCD Unit ..........................................................................................................................14- 1914.3.3 Adjusting the Position of the No. 1/No. 2 Mirror Base .......................................................................................14- 1914.3.4 When Replacing the Copyboard Glass..............................................................................................................14- 2014.3.5 When Replacing the Reading Glass..................................................................................................................14- 2014.3.6 When Replacing the Scanning Lamp ................................................................................................................14- 2014.3.7 After Replacing the Inverter PCB.......................................................................................................................14- 20
14.4 Laser Exposure System........................................................................................................................14- 2014.4.1 When Replacing the Scanner Unit.....................................................................................................................14- 20
14.5 Image Formation System......................................................................................................................14- 2014.5.1 Outline ..............................................................................................................................................................14- 2014.5.2 Routing Charging Wire .....................................................................................................................................14- 2014.5.3 Routing Grid for Primary Charging Assembly ................................................................................................... 14- 2114.5.4 Adjusting Height of Charging Wire ....................................................................................................................14- 2114.5.5 Mounting Cleaning Blade ..................................................................................................................................14- 2214.5.6 Removing Side Seal .........................................................................................................................................14- 22
14.6 Fixing System .......................................................................................................................................14- 2214.6.1 Applying Grease After Replacing the Fixing Roller............................................................................................14- 2214.6.2 Adjusting the Nip Width .....................................................................................................................................14- 2314.6.3 Adjusting the Fixing Web Solenoid (SL9) ..........................................................................................................14- 2314.6.4 After Replacing the Fixing Web .........................................................................................................................14- 2314.6.5 Adjusting the Fixing Inlet Guide Solenoid (SL1) ................................................................................................14- 2314.6.6 Adjusting the Position of the Fixing Inlet Guide .................................................................................................14- 23
14.7 Electrical Components ..........................................................................................................................14- 2314.7.1 When Replacing DC Controller PCB ................................................................................................................14- 2314.7.2 When Replacing HVT PCB ............................................................................................................................... 14- 2414.7.3 After Replacing the HDD ...................................................................................................................................14- 2414.7.4 When Replacing the Main Controller PCB.........................................................................................................14- 24
14.8 Pickup/Feeding System ........................................................................................................................14- 2414.8.1 Points to Note When Mounting the Pickup Roller..............................................................................................14- 2414.8.2 Points to Note When Mounting the Separation Roller .......................................................................................14- 2414.8.3 The Points to Mount the Feeding Roller ............................................................................................................14- 2414.8.4 Adjusting the Pressure of the Deck/Cassette Separation Roller ....................................................................... 14- 25
Contents
14.8.5 Adjusting the Pressure of the Manual Separation Roller ...................................................................................14- 2514.8.6 Adjusting the Position of the Pickup Solenoid (SL3, SL4) of the Cassette 3/4 ..................................................14- 2514.8.7 Adjusting the Position of the Delivery Flapper Solenoid (SL5)...........................................................................14- 2514.8.8 Adjusting the Position of the Right Deck Pickup Solenoid (SL6) .......................................................................14- 2514.8.9 Adjusting the Position of the Left Deck Pickup Solenoid....................................................................................14- 2614.8.10 Mounting the Reversing Flapper Solenoid .......................................................................................................14- 2614.8.11 Attaching the Side Guide Timing Belt in the Manual Feed Tray Assembly ......................................................14- 2614.8.12 Adjusting the Position of the Lifter Motor M20/M21 of the Cassette 3/4 ..........................................................14- 26
Chapter 15 Correcting Faulty Images
15.1 Making lnitial Checks.............................................................................................................................. 15- 115.1.1 Site Environment..................................................................................................................................................15- 115.1.2 Checking the Originals for Symptoms..................................................................................................................15- 115.1.3 Copyboard Cover, Copyboard Glass, and Standard White Plate ........................................................................15- 115.1.4 Checking the Charging Assemblies .....................................................................................................................15- 115.1.5 Checking the Developing Assembly.....................................................................................................................15- 115.1.6 Checking the Paper..............................................................................................................................................15- 115.1.7 Checking the Periodically Replaced Parts ...........................................................................................................15- 115.1.8 Image Adjustment Basic Procedure.....................................................................................................................15- 115.1.9 Others ..................................................................................................................................................................15- 1
15.2 Outline of Electrical Components ........................................................................................................... 15- 215.2.1 Clutch/Solenoid ....................................................................................................................................................15- 2
15.2.1.1 Clutches and Solenoids ....................................................................................................................................................... 15- 215.2.2 Motor ....................................................................................................................................................................15- 3
15.2.2.1 Motors .................................................................................................................................................................................. 15- 315.2.3 Fan.......................................................................................................................................................................15- 6
15.2.3.1 Fans ..................................................................................................................................................................................... 15- 615.2.4 Sensor..................................................................................................................................................................15- 8
15.2.4.1 Sensors ................................................................................................................................................................................ 15- 815.2.5 Switch.................................................................................................................................................................15- 13
15.2.5.1 Switches............................................................................................................................................................................. 15- 1315.2.6 Lamps, Heaters, and Others ..............................................................................................................................15- 14
15.2.6.1 Lamps, Heaters, and Others .............................................................................................................................................. 15- 1415.2.7 PCBs..................................................................................................................................................................15- 16
15.2.7.1 PCBs ................................................................................................................................................................................. 15- 1615.2.8 Connectors.........................................................................................................................................................15- 18
15.2.8.1 Connectors......................................................................................................................................................................... 15- 1815.2.9 Variable Resistors (VR), Light-Emitting Diodes (LED), and Check Pins by PCB...............................................15- 25
15.2.9.1 Variable Resistors (VR), Light-Emitting Diodes, and Check Pins by PCB ......................................................................... 15- 2515.2.9.2 DC Controller PCB ............................................................................................................................................................. 15- 2515.2.9.3 DC Power Supply PCB ...................................................................................................................................................... 15- 2615.2.9.4 HVT PCB............................................................................................................................................................................ 15- 26
Chapter 16 Self Diagnosis
16.1 Error Code Table .................................................................................................................................... 16- 116.1.1 Error Code............................................................................................................................................................16- 1
16.2 Error Code Details .................................................................................................................................. 16- 216.2.1 Detail Error Code .................................................................................................................................................16- 216.2.2 E602 in Detail.....................................................................................................................................................16- 15
16.3 Error Code (SEND)............................................................................................................................... 16- 1716.3.1 Results of Self-Diagnosis ...................................................................................................................................16- 1716.3.2 Error Codes........................................................................................................................................................16- 19
16.4 Jam Code ............................................................................................................................................. 16- 2416.4.1 Jam Code (machine proper) ..............................................................................................................................16- 2416.4.2 Jam Code (finisher-related)................................................................................................................................16- 24
Contents
16.4.3 Jam Code (ADF-related)....................................................................................................................................16- 2516.5 Alarm Code...........................................................................................................................................16- 26
16.5.1 Alarm Code........................................................................................................................................................16- 26
Chapter 17 Service Mode
17.1 Outline ....................................................................................................................................................17- 117.1.1 Service mode screen configuration .....................................................................................................................17- 117.1.2 Entering or selecting service modes....................................................................................................................17- 117.1.3 Exiting service modes..........................................................................................................................................17- 217.1.4 Backing Up Service Mode ...................................................................................................................................17- 217.1.5 Initial screen.........................................................................................................................................................17- 217.1.6 Main/intermediate item screen.............................................................................................................................17- 317.1.7 Sub-item screen...................................................................................................................................................17- 3
17.2 DISPLAY (Status Display Mode) ............................................................................................................17- 417.2.1 COPIER ............................................................................................................................................................... 17- 4
17.2.1.1 COPIER List......................................................................................................................................................................... 17- 417.2.2 FEEDER ..............................................................................................................................................................17- 9
17.2.2.1 FEEDER List ........................................................................................................................................................................ 17- 917.3 I/O (I/O Display Mode) ..........................................................................................................................17- 10
17.3.1 Outline ...............................................................................................................................................................17- 1017.3.2 R-CON ...............................................................................................................................................................17- 1117.3.3 FEEDER ............................................................................................................................................................17- 1217.3.4 SORTER............................................................................................................................................................17- 1317.3.5 MN-CON ............................................................................................................................................................17- 1817.3.6 P-CON ...............................................................................................................................................................17- 18
17.4 ADJUST (Adjustment Mode).................................................................................................................17- 2217.4.1 COPIER ............................................................................................................................................................. 17- 22
17.4.1.1 COPIER List....................................................................................................................................................................... 17- 2217.4.2 FEEDER ............................................................................................................................................................17- 26
17.4.2.1 FEEDER List ...................................................................................................................................................................... 17- 2617.4.3 SORTER............................................................................................................................................................17- 26
17.4.3.1 SORTER List...................................................................................................................................................................... 17- 2617.5 FUNCTION (Operation/Inspection Mode).............................................................................................17- 26
17.5.1 COPIER ............................................................................................................................................................. 17- 2617.5.1.1 COPIER List....................................................................................................................................................................... 17- 26
17.5.2 FEEDER ............................................................................................................................................................17- 3517.5.2.1 FEEDER List ...................................................................................................................................................................... 17- 35
17.6 OPTION (Machine Settings Mode) .......................................................................................................17- 3617.6.1 COPIER ............................................................................................................................................................. 17- 36
17.6.1.1 COPIER List....................................................................................................................................................................... 17- 3617.6.2 FEEDER ............................................................................................................................................................17- 58
17.6.2.1 FEEDER List ...................................................................................................................................................................... 17- 5817.6.3 SORTER............................................................................................................................................................17- 58
17.6.3.1 SORTER List...................................................................................................................................................................... 17- 5817.6.4 BOARD..............................................................................................................................................................17- 59
17.6.4.1 BOARD List........................................................................................................................................................................ 17- 5917.7 TEST (Test Print Mode) ........................................................................................................................17- 59
17.7.1 COPIER ............................................................................................................................................................. 17- 5917.7.1.1 COPIER List....................................................................................................................................................................... 17- 59
17.8 COUNTER (Counter Mode) ..................................................................................................................17- 6017.8.1 COPIER ............................................................................................................................................................. 17- 60
17.8.1.1 COPIER List....................................................................................................................................................................... 17- 60
Chapter 18 Upgrading
18.1 Outline ....................................................................................................................................................18- 1
Contents
18.1.1 Outline of Upgrading the Machine........................................................................................................................18- 118.1.2 Outline of the Service Support Tool ....................................................................................................................18- 1
18.2 Making Preparations............................................................................................................................... 18- 418.2.1 Registering the System Software.........................................................................................................................18- 418.2.2 Making Connections.............................................................................................................................................18- 6
18.3 Formatting the HDD................................................................................................................................ 18- 818.3.1 Formatting All Partitions .......................................................................................................................................18- 818.3.2 Formatting Selected Partitions .............................................................................................................................18- 918.3.3 Formatting the Partitions ......................................................................................................................................18- 9
18.4 Downloading System Software............................................................................................................. 18- 1118.4.1 Downloading System .........................................................................................................................................18- 11
18.4.1.1 Outline................................................................................................................................................................................ 18- 1118.4.1.2 Downloading Procedure..................................................................................................................................................... 18- 11
18.4.2 Downloading RUI, and Language ......................................................................................................................18- 1318.4.2.1 Outline................................................................................................................................................................................ 18- 1318.4.2.2 Downloading Procedure..................................................................................................................................................... 18- 15
18.4.3 Downloading SDICT...........................................................................................................................................18- 1618.4.3.1 Outline................................................................................................................................................................................ 18- 1618.4.3.2 Downloading Procedure..................................................................................................................................................... 18- 16
18.4.4 Downloading MEAPCONT.................................................................................................................................18- 1818.4.4.1 Outline................................................................................................................................................................................ 18- 1818.4.4.2 Downloading Procedure..................................................................................................................................................... 18- 18
18.4.5 Downloading KEY ..............................................................................................................................................18- 1918.4.5.1 Outline................................................................................................................................................................................ 18- 1918.4.5.2 Downloading Procedure..................................................................................................................................................... 18- 20
18.4.6 Downloading the TTS.........................................................................................................................................18- 2118.4.6.1 Outline................................................................................................................................................................................ 18- 2118.4.6.2 Downloading Procedure..................................................................................................................................................... 18- 21
18.4.7 Downloading BOOT ...........................................................................................................................................18- 2218.4.7.1 Outline................................................................................................................................................................................ 18- 2218.4.7.2 Downloading Procedure..................................................................................................................................................... 18- 23
18.4.8 Downloading Dcon and Rcon.............................................................................................................................18- 2418.4.8.1 Outline................................................................................................................................................................................ 18- 2418.4.8.2 Downloading Procedure..................................................................................................................................................... 18- 25
18.4.9 Downloading G3 FAX.........................................................................................................................................18- 2618.4.9.1 Outline................................................................................................................................................................................ 18- 2618.4.9.2 Downloading Procedure..................................................................................................................................................... 18- 27
18.4.10 Uploading and Downloading Backup Data.......................................................................................................18- 2818.4.10.1 Outline .............................................................................................................................................................................. 18- 2818.4.10.2 Uploading Procedure........................................................................................................................................................ 18- 2918.4.10.3 Downloading Procedure ................................................................................................................................................... 18- 31
Chapter 19 Service Tools
19.1 Service Tools .......................................................................................................................................... 19- 119.1.1 List of Special Tools .............................................................................................................................................19- 119.1.2 List of Solvents/Oils..............................................................................................................................................19- 2
Chapter 1 Introduction
Contents
Contents
1.1 System Construction ......................................................................................................................................................1-11.1.1 System Configuration with Pickup/Delivery Accessories (230V)EUR ...................................................................................... 1-11.1.2 System Configuration with Printing/Transmission Accessories (230V)EUR ............................................................................. 1-11.1.3 Functions and Printing/Transmission Accessories (230V).......................................................................................................... 1-2
1.2 Product Specifications....................................................................................................................................................1-31.2.1 Names of Parts ............................................................................................................................................................................. 1-3
1.2.1.1 External view ..................................................................................................................................................................................................1-31.2.1.2 Cross-Section ..................................................................................................................................................................................................1-5
1.2.2 Using the Machine ....................................................................................................................................................................... 1-71.2.2.1 Turning On the Power Switch.........................................................................................................................................................................1-71.2.2.2 Turning Off the Power Switch ........................................................................................................................................................................1-71.2.2.3 Control Panel...................................................................................................................................................................................................1-9
1.2.3 User Mode Items.......................................................................................................................................................................... 1-91.2.3.1 Common Settings ............................................................................................................................................................................................1-91.2.3.2 Timer Settings ...............................................................................................................................................................................................1-111.2.3.3 Adjustment/Cleaning.....................................................................................................................................................................................1-111.2.3.4 Report Output................................................................................................................................................................................................1-111.2.3.5 System Control Settings................................................................................................................................................................................1-121.2.3.6 Copier Specifications ....................................................................................................................................................................................1-141.2.3.7 Transmission/Reception Settings ..................................................................................................................................................................1-151.2.3.8 Box Settings ..................................................................................................................................................................................................1-161.2.3.9 Printer Settings ..............................................................................................................................................................................................1-161.2.3.10 Address Book Settings ................................................................................................................................................................................1-181.2.3.11 Voice Guide Settings...................................................................................................................................................................................1-19
1.2.4 Maintenance by the User ........................................................................................................................................................... 1-191.2.4.1 Cleaning ........................................................................................................................................................................................................1-191.2.4.2 Checks ...........................................................................................................................................................................................................1-20
1.2.5 Safety ......................................................................................................................................................................................... 1-211.2.5.1 Safety of the Machine's Laser Unit ...............................................................................................................................................................1-211.2.5.2 CDRH Regulations........................................................................................................................................................................................1-211.2.5.3 Handling the Machine's Laser Unit...............................................................................................................................................................1-221.2.5.4 Safety of Toner..............................................................................................................................................................................................1-22
1.2.6 Product Specifications ............................................................................................................................................................... 1-221.2.6.1 Product Specifications...................................................................................................................................................................................1-22
1.2.7 Function List .............................................................................................................................................................................. 1-241.2.7.1 Paper Types...................................................................................................................................................................................................1-241.2.7.2 Printing Speed ...............................................................................................................................................................................................1-241.2.7.3 Paper Types/Printing Speed (K paper)..........................................................................................................................................................1-25
Chapter 1
1-1
1.1 System Construction
1.1.1 System Configuration with Pickup/Delivery Accessories (230V)EUR0015-9473
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows a typical system configuration:
F-1-1T-1-1
1.1.2 System Configuration with Printing/Transmission Accessories (230V)EUR0015-4289
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows a typical system configuration:
[1] Finisher-AD1[2] Saddle Finisher-AD2[3] Shift Tray-D1[4] Copy Tray-L1[5] Puncher Unit-AS1/AU1/AV1[6] DADF-S1 (standard)
[7] Document Tray-M1[8] Paper Deck-AD1 (A4)[9] Paper Deck-AE1 (A3)[10] Paper Folding Unit-E1[11] Document Insertion/ Folding Unit-F1[12] Staple Cartridge-J1[13] Staple Cartridge-D2/D3[14] ADF Access Handle-A1
[3]
[4]
[1]
[2]
[5]
[8]
[9]
[6]
[12]
[13]
[11]
[10]
[14][7]
Chapter 1
1-2
F-1-2T-1-2
1.1.3 Functions and Printing/Transmission Accessories (230V)0015-4296
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the accessories needed for individual functions:T-1-3
[1] Expansion Bus-D2
[2] Voice Guidance Kit-B1
[3] Super G3 FAX Board-Z1
[4] HDD Data Encryption Kit-B2
[5] Card Reader-C1
[6] Card Reader Attachment-C2
[7] HDD Data Erase Kit-A1 (license certificate)
[8] UFR II/PCL Printer Kit-R1 (license certificate)
[9] PS Printer Kit-R1 (license certificate)
[10] Barcode Printing Kit-A1 (license certificate)
[11] Encrypted Printing Software-C1 (license certificate)
[12] Universal Send Searchable PDF Kit-A1 (license certificate)
[13] Digital User Signature PDF Kit-A1 (license certificate)
[14] Web Access Software-F1 (license certificate)
[15] Remote Operator's Software Kit-A2 (license certificate)
[16] Secure Watermark-A1 (license certificate)
[17] AMS KIT (license certificate)
[18] Universal Send Trial Kit-C1 (license certificate) (standard)
[19] Canon Universal Send Kit-F1 (license certificate)
Function Accessory needed
LIPS printing LPS V Expansion Kit-R1
transmission SEND Expansion Kit-Q1
[1]
[4]
[3]
[7]
[10]
[2]
[14]
[8] [9]
[11] [13]
[18] [19]
[12]
[17][16][15]
[2]
[5]
[6]
Chapter 1
1-3
1.2 Product Specifications
1.2.1 Names of Parts
1.2.1.1 External view0015-4304
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
faxing Super G3 Fax Board-Z1
LIPS printing + transmission LIPS V Expansion Kit-R1SEND Expansion Kit-Q1
LIPS printing + faxing (1-line)LIPS V Expansion Kit-R1Super G3 Fax Board-Z1
MEAP function(w/ copy boot ROM)
- no need for memory expansionboth MEAP authentication and MEAP application operation possible
MEAP function(w/ LIPS LX boot ROM)
- if only MEAP authentication is desiredno need for memory expansion; if MEAP application is installed, device will not start up (indicating 'E604-0001')- if both MEAP authentication and MEAP application are desired
MEAP application USB connection HDD Data Encryption Kit-B2Expansion Bus-D2
security function(HDD formatting + encryption)
HDD Data Encryption Kit-B2HDD Data Erase Kit-A1Expansion Bus-D2
PDF/TIFF/JPEG direct printingLIPS LX Printer & Scanner Unit-R1LIPS V Expansion Kit-R1Direct Printing Expansion Kit-F1
searchable PDF function SEND Expansion Kit-Q1Universal Send Searchable PDF Kit-A1
Electronic signature PDF function User Signature PDF-A1
voice guidance Voice Guidance Kit-B1Expansion Bus-D2
remote operation Remote Operation Kit-A1
Web browsing Web Browser Expansion Kit-C2
Secure print function Encrypted Printing Software A1
Function Accessory needed
Chapter 1
1-4
F-1-3[1] Feeder[2] Control panel[3] Toner access cover[4] Front cover[5] Right front deck[6] Cassette 3[7] Cassette 4[8] Left front deck[9] Left cover (paper)[10] Environment switch[11] Cassette heater switch[12] Leakage breaker[13] Left cover (middle)[14] Delivery cover[15] Left cover (upper)[16] Reader left cover[17] Reader front cover
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[11]
[10]
[12]
[13]
[14]
[15]
[16]
[17]
Chapter 1
1-5
F-1-4[18] Reader right cover[19] Reader rear cover[20] Read cover (upper)[21] Right cover (upper rear)[22] Rear cover (lower)[23] Main power switch[24] Right cover (lower rear)[25] Right cover (lower)[26] Right door unit (lower)[27] Right door unit (upper)[28] Manual feed pickup tray[29] Right cover (upper)[30] Çbharger unit (iR5075 Japan model only)
1.2.1.2 Cross-Section0015-4306
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[18]
[19]
[20]
[21]
[22]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
Chapter 1
1-6
F-1-5T-1-4
[1] Scanning lamp [2] Read roller 1 [3] Platen roller 1 [4] Read roller 2 [5] Platen roller 2 [6] CIS unit [7] Secondary registration roller [8] Read roller 3 [9] Reversing roller [10] Primary registration roller [11] Delivery roller [12] Feeding roller [13] Pickup roller [14] Copyboard glass
[15] Laser mirror 2 [16] Laser mirror 3[17] Laser mirror 1 [18] CCD unit[19] Drum cleaner assembly [20] Primary charging assembly[21] Photosensitive drum [22] Laser mirror 4[23] Laser unit [24] Dust-proofing glass[25] Developing cylinder [26] Pre-transfer charging assembly[27] Manual feed pull-out roller [28] Manual feed feed roller[29] Manual feed separation roller [30] Registration roller[31] Transfer charging assembly [32] Separation charging assembly[33] Right deck feed roller [34] Right deck separation roller[35] Right deck pickup roller [36] Right deck[37] Cassette 3 pickup roller [38] Cassette 3 feed roller[39] Cassette 3 separation roller [40] Cassette 4 pickup roller
[43]
[42]
[36]
[29]
[44]
[45]
[48]
[47]
[49]
[51]
[52]
[53]
[54]
[55]
[50]
[46]
[41]
[39]
[38]
[40]
[37]
[30]
[31]
[35]
[34]
[28]
[27]
[26]
[25]
[22]
[21]
[20]
[19]
[24]
[33]
[32]
[23]
[18][5]
[1]
[2]
[4][7][6] [9][8] [11] [12] [13][10]
[57]
[58]
[59]
[56]
[15] [16] [17][14]
[3]
Chapter 1
1-7
1.2.2 Using the Machine
1.2.2.1 Turning On the Power Switch0015-4307
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine is equipped with 2 power switches: main power switch and control panel power switch. Normally, i.e., other than sleep state, the machine starts upwhen the main power switch is turned on.
F-1-6
[1] Control panel power switch[2] Main power switch[3] Main power lamp
Never turn off the main power switch while the progress bar is shown, indicating that the machine HDD is being accessed. Otherwise, the HDD can develop a fault(E602).
F-1-7
1.2.2.2 Turning Off the Power Switch0015-4309
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[41] Cassette 4 feed roller [42] Cassette 4 separation roller[43] Cassette 4 [44] Cassette 3[45] Left deck [46] Left deck separation roller[47] Left deck feed roller [48] Left deck pickup roller[49] Fixing lower roller [50] Internal delivery roller[51] External delivery roller [52] Fixing upper roller[51] Fixing assembly [54] Fixing web[55] Feeding assembly [56] No.3 mirror[57] No.1 mirror [58] No.2 mirror[59] ADF reading glass
OFF
ON
[2]
Enargy Saver
Counter Check
Stop
Start
Processing/Data PowerError
Clear
ABC
Additional Functions
Help
Reset
ON/OFF
DEF
GHI JKL MNO
PQRS TUV WXYZ
Display Contrast
[3]
[1]
Starting up. Please wait.
Chapter 1
1-8
Be sure to go through the shut-down sequence whenever turning off the main power switch.
How to Turn Off the Main Power SwitchTo turn off the main power switch, be sure to go through the following steps to prevent damage to the machine's hard disk:1) Hold down the control panel power switch for 3 sec or more.
2) Go through the down-sequence instructions indicated on the touch panel so that the main power switch may be turned off.3) Turn off the main power switch.
F-1-8
While Downloading Is Under WayNever turn off the main power switch/control panel power switch while downloading is under way. (If the main power switch is turned off while downloading isunder way, the machine can fail to operate.)
[1]
[2] [3]
ON/OFF
OFF
ON
Chapter 1
1-9
F-1-9
1.2.2.3 Control Panel0015-4310
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-1-10
1.2.3 User Mode Items
1.2.3.1 Common Settings0015-4313
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory settings.**Indicated when the appropriate accessory is installed.
T-1-5
[1] Touch Panel Display [2] Initial Settings/Registration Key [3] Easy NAVI Key [4] Release key[5] Keypad [6] Power Save key[7] Control panel power switch [8] Counter Check Key [9] Touch Pen [10] Clip recess[11] Stop key [12] Start key[13] Main power lamp [14] Error lamp[15] Execute/Memory lamp [16] Clear key[17] ID (Authentication) Key [18] Display contrast dial
Mode Descriptioninitial function select initial function: *copier/transmit/fax, print,box/MEAP
ON/OFF
OFF
ON
Enargy Saver
Counter Check
Stop
Start
Processing/Data PowerError
Clear
ABC
Additional Functions
Help
Reset
ON/OFF
DEF
GHI JKL MNO
PQRS TUV WXYZ
Display Contrast
[11][12][13][14][18] [17] [15][16]
[1] [2] [3] [4] [5] [6] [7] [8] [9] [10]
Chapter 1
1-10
use 'system status screen' as initial screen: ON/*OFF
give priority to 'device' of 'system status screen': *ON/OFF
post-auto clear function *use previous/do not use previous
function group order setup: group A, MEAP, group B
enable/disable buzzer input sound: *ON/OFFinput invalid sound: ON/*OFFreplenish alert sound: ON/*OFFalert sound: *ON/OFFjob end sound: *ON/OFF
indicate power level message *ON/OFF
inch input ON/*OFF (if US, *ON)enable/disable cassette auto select copier/printer/box/other (manual feed: ON/*OFF + individual cassette: *ON/OFF)
consider copy/power type: *ON/OFF (toggle)
register paper type right cassette deck/left cassette deck: plain paper/colored paper/recycled paper/heavy paper/bond paper (outside Japan)/letterhead (plain paper; outside Japan)/letterhead (heavy paper; outside Japan)/punched paper (outside Japan)
cassettes 3/cassette 4: *plain paper/colored paper/recycled paper/bond paper (outside Japan)/letterhead (plain paper; outside Japan)/letterhead (heavy paper; outside Japan)/punched paper (outside Japan)/index sheet
cassette 5 (paper deck): *plain paper/colored paper/recycled paper/heavy paper/bond paper (outside Japan)/letterhead (heavy paper; outside Japan)/punched paper (outside Japan)
change power save mode *-10%, -25%, -50%, no recovery interval
set power consumption level in sleep state *low/high
set delivery tray**(w/ finisher)
With Finisher, AD1 / Saddle Finisher, AD2 attached
Tray A: Copy, box, printer, *reception/*fax, *others*Tray B: *Copy, *box, *printer, reception/fax, othersTray C: *Copy, *box, *printer, reception/fax, others
Basic position of the tray: *Tray B / Tray C / Not specified
set printing priority copier: *1/2/3
printer: 1/*2/3box: 1/2/*3reception/fax: 1/2/*3other: 1/2/*3
register image for image merge register: original size/full merge, see-through merge (20, *50, 99%) form name (24 characters max.) form read delete
check coy: cassette select, print sortdetail info: display detail info, change form name
register character string for print/stamp register/edit: change character string (16 character max.)
delete
register manual feed paper standard mode ON (select paper size/select paper type)/*OFF
select standard mode for local print select paper type: *auto paper select/paper source selectnumber of prints: *1 to 9999sorter: sort/group/staple sort/*shift sort/shift group/rotation sort/rotation group/punch hole/z-fold/C-foldduplex print: ON (open like book/open like calendar) OFFdelete file after printing:merge file:
switch language ON/*OFFreverse screen color ON/*OFF between-job shift** *ON/OFF
Mode Description
Chapter 1
1-11
1.2.3.2 Timer Settings0015-4316
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.T-1-6
1.2.3.3 Adjustment/Cleaning0015-4317
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.**Indicated when the appropriate accessory is installed.
T-1-7
1.2.3.4 Report Output0015-4318
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.**Indicated when the appropriate accessory is installed.
T-1-8
between-job interleaf ON (paper source select) *OFF
between-set interleaf ON (setting range between *10 and 9999; paper source select) *OFF
right wait time indication copier/box/other (for each, ON/*OFF)
Registration of the size of the side paper deck** A3/A4/A4R/B4/B5/11×17/LGL/LTR/LTRR
output tray paper mix** *ON/OFF
original reading area cleaning prompt *ON/OFF
function limit mode** ON/*OFF
shut-down mode execute keyreset common settings Do you really want to reset?: yes/no
Mode Descriptiontime fine-adjust by +/- in 1-min increments
auto sleep time 10 sec; *1, 2, 10, 15, 20, 30, 40, 50 min; 1 hr; 90 min; 2, 3,4 hr
auto clear time 0=none, 1, ..., *2, ..., 9 min (in 1-min increments)silent mode shift time 0=none, 1*, ..., 9 min (1-min increments)
set weekly timer everyday from Sun to Sat (00:00 to 23:59; in 1-min increments)
Mode Descriptionzoom fine-adjust XY, independent: -1.0% to +1.0% (in 0.1%-increments), *0%
center bind staple edging** start key
change middle bind position**(w/ saddle finisher)
size: A3, 11x17/B4/A4R, LTR, LGLposition: -2.0 mm to +2.0 mm (in -0.25-mm increments), *0 mm
Adjustment of the creep (displacement) correction volume
Correction volume (For each type of paper): 0.00 to 2.00mm(Interval of 0.05mm) *0.25mm
Adjustment of the folding position** Adjustment of Z-fold position-2mm to +1.5mm, *0mm (incremented by 0.5mm)Adjustment of C-fold positionA: 0.0mm to 6.0mm, *0mmB: 0.0mm to 3.0mm, *0mm (incremented by 0.5mm)
correct density copier/box, transmit; 9 steps each (at time of shipment, set to '5')
Adjustment of contrast of characters/background Relative contrast value: -7 to *+7, 0Print setting for sample printingSetting of the standard value: 0 to 64, *20Density of a latent image: 0 to 36, *8
Feeder cleaning Start key
Drum cleaning Start key
Wire cleaning Start key
Mode Description
transmit (specifications setup)** transmission result report: *only if error/ON/OFF
indicate transmission original: *ON/OFF
Mode Description
Chapter 1
1-12
1.2.3.5 System Control Settings0015-4320
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.**Indicated when the appropriate accessory is installed.***Indicated when the appropriate accessory is installed.ÅiiR5065,iR5055Åj
T-1-9
transmission control report print every 100 communications: *ON/OFF print at specific time: *ON/OFF time settings: *00:00 to 23:59 separate transmission/reception: (toggle) ON/*OFF
fax(specifications setup)**
fax transmission result report: *only if error/ON/OFF
indicate transmission original: *ON/OFF
fax communications control report print automatically every 40 communications: *ON/OFF
print at specific time: ON/*OFF time setting: *00:00 to 23:59 separate transmission/reception: (toggle) ON/*OFFfax reception results report: *only if error/ON/*OFF
fax box reception report: *ON/OFFprint list(transmission)**
address book list: print list
user data request: Do you want to print the user data list?: yes/no
print list(fax)**
user data list: Do you want to print the user data list?: yes/no
Mode Descriptionset system administrator information system control group ID: 7 characters max.
system control ID: 7 characters max.system administrator name: 32 bytes
mail address: 64 bytescontact: 32 bytescomment: 32 bytes
group ID controller group ID control: ON/*OFF
ID No. register: register, edit, delete, function control
count control: clear, count print, all clear
print job w/ unknown ID: *ON/OFF
scan job w/ unknown job: *ON/OFF
communication control setup e-mail/**i-fax setup
transmission data size upper limit: 0=none, 1 to 99 MB; *3 MB
abbreviation: 40 characters or 20 2-byte characters; *attached imagestransmission time-out in full state: 1 to 99 hr, *24 hrTimeout in divided reception: 1 to 99 hours, *24 hours
print for MDN/DSN reception: ON/*OFF
always notify if reception error: *ON/OFF
relay through server: ON/*OFFPermit MDN not via server: *ON/OFF
fax setup**
transmission start speed: *33600bps, 14400bps, 9600bps, 7200bps, 4800bps, 2400bps
reception start speed: 33600bps*, 14400bps, 9600bps, 7200bps, 4800bps, 2400bps
reception password: 20 characters max.
FIS switch: ON/*OFF
system box setup
system box ID No.**: 7 characters
use fax memory reception**: ON/*OFF
use i-fax memory reception**: ON/*OFF
memory reception start time**: by day, by day of week, *no specification
Mode Description
Chapter 1
1-13
memory reception end time**: by day, by day of week, *no specificationenable/disable remote UI *ON/OFF
use SSL: ON/*OFF
limit target** address book ID No.: 7 characters max.
address book access No. control: ON/*OFF
new target limit: ON/*OFF
Permit transmission from the fax driver *ON/OFF
Entry for confirmation when entering a fax number ON/*OFF
Restrictions of the domain for transmission of email/IFAX
Restrictions of the domain for transmission: ON/*OFFPermitted domain for transmission: Registration, details/edit, deletion
Permit PDF transmission when using an expired certificate
ON/*OFF
Always attach a device signature when performing PDF transmission
ON/*OFF
device information setup device name: 32 characters, or 16 2-byte characters
installation site: 32 characters, or 16 2-byte characters
transfer setup** reception method, enable/disable condition, registration, unconditional transfer registration, e-mail priority, detail/edit, delete, list print
delete bulletin delete
auto on-line/off-line shift*** auto on-line shift: ON/*OFF
auto off-line shift: ON/*OFF
date/time setup: set (12 numeric characters)time zone: GMT -12:00 to GMT +12:00 (GMT +*9:00)daylight saving time: ON/*OFF
adjust date/time set (12 characters)time zone: GMT -12:00 to GMT +12:00 (GMT +*9:00)daylight saving time: ON, *OFF
register LDAP server** register, detail/edit, delete, Registration/edit of LDAP search attributes,list print
register license 24 characters
set print expansion ON/*OFFgroup ID: ON/*OFFdate: ON/*OFFtext: ON/*OFF
Restrictions in the system status screen Display the job status before authentication: *ON/OFF
Permit secure print from the print status: ON/*OFF
Display the job history: *ON/OFF
Obtain the job history from the management software: Permit / Prohibit
MEAP setup use HTTP: *ON/OFFuse SSL: ON/*OFF
print system info: print
Mode Description
Chapter 1
1-14
1.2.3.6 Copier Specifications0015-4322
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.**Indicated when the appropriate accessory is installed.
T-1-10
set machine information distribution - register recipient:auto search/register, register, detail info, delete,list printing
- auto distribution:every day, by day of week, *no specificationuser mode setting: ON/*OFFnetwork setup: include, do not includegroup ID: ON/*OFFaddress book: ON/*OFFSetting of the print specifications: ON/*OFF
- manual distribution setup: user mode settings; ON/*OFFnetwork setup: include, do not includegroup ID: ON/*OFFaddress book: ON/*OFFSetting of the print specifications: ON/*OFF
- limit reception according to originalON/*OFF
- recover data:user mode settings, group ID, address book,setting of the print specifications
- time reception according to machine:user mode settings; *ON/OFFgroup ID: *ON/OFFaddress book: *ON/OFFSetting of the print specifications: ON/*OFF
Setting of the print specifications: ON/*OFF
Initialization of all data/settings Initialization
ON/OFF to display ID/user name *ON/OFF
Setting of the encryption secure print Reception of the encryption secure print job: ON/*OFFAutomatic printing when using an IC card: ON/*OFF
USB setting Use the USB device: *ON/OFFUse the USB host: *ON/OFF
ON/OFF to display hidden characters when entering secret information
*ON/OFF
Forcible tint block printing mode** Copy: *Disable / EnableBox: *Disable / EnablePrint: *Disable / Enable
Simultaneous setting for user box Time until the document is automatically deleted: (0, 1, 2, 3, 6, 12) hours, (1, 2, *3, 7, 30) daysPrint when saving the data from the printer driver: *ON/OFF
Mode Descriptionquick screen paper select key setup large* (manual feed/manual feed paper change reservation/(paper source) 1*/(paper source) 2*/(paper source)
3*/(paper source) 4*/(paper source) 5/small
single screen preference key 1 setup *no setting, individual modes
simple scan preference key 2 setup *no setting, individual modes
quick screen preference key setup number of preference keys indicated: 5*/10 setup: set location -> set individual keys *no setting, individual modes
auto sort** *ON/OFF
priority on screen orientation ON/OFF*
auto vertical/horizontal rotation *ON/OFF
print photo mode ON/*OFFchange standard mode register/reset (factory shipment: 1 set, auto paper select, auto density, auto image quality; printer: local)
register remote copy printer priority/register (7 units max.)/detail info/delete
remote copy transmission time-out *30 (5 to 30) sec
Mode Description
Chapter 1
1-15
1.2.3.7 Transmission/Reception Settings0015-4324
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.**Indicated when the appropriate accessory is installed.
T-1-11
reset copier specifications Do you want to reset? yes/no(auto sort: ON/face-up delivery: ON/preference key setup: no)
Mode Descriptionset common transmission settings** register source name**: 01 to 99; register/edit (24 characters max.); delete
register user abbreviation**: 24 characters max.permit use of non-ASCII code for FTP transmission**: (ON/*OFF)
error file clear**: (*ON/OFF)error transfer file handling**: always print/save/print/*offprint photo mode**: (ON/*OFF)number of retries**: (*3 times; 0 to 5 times)
change transmission function standard mode**
read mode: black-and-white machine default *black at 200 dpi/black at 300 dpi/black at 600 dpi/black at 400 dpi (Note: if fax only, black at 200x100*/black at 200x200/black at 200x400/black at 400x400)file type: *TIFF/PDF/PDF(OCR)divide by page: (toggle) ON/*OFF
register routine task button**: (register/edit, delete; display comment: ON/*OFF)
Display a confirmation message when calling the routine task button: *ON/OFF
PDF (OCR setup)**
original orientation auto detection: (*ON/OFF)limit number of characters in file name (OCR): (1 to *24)
Check the certificate of the device signature
Detailed information of the certificate: Verification of the certificate
Check the certificate of the user signature
Detailed information of the certificate: Verification of the certificate
Display a confirmation message when sending the IC card signature: *ON/OFF
transmission screen initial display**: routine task button/one-touch button/*new address
transmission source record**: *keep/do not keep
indication location: inside image/*outside imagetarget abbreviation indication: (*ON/OFF)telephone number marking: *FAX/TEL
Use the chunk divided transmission function when sending WebDAV: *ON/OFF
Display a confirmation message to check the "Completed" stamp for double-sided transmission: *ON/OFF
reset transmission settings: Do you want to reset? yes/no
common reception setup** duplex record (ON/*OFF)
cassette select
switch A: (*ON/OFF)switch B: (*ON/OFF)switch C: (*ON/OFF)switch D: (*ON/OFF)
image reduction
image reception: (*ON/OFF)reduction mode: *auto/fixedfixed mode reduction rate: E210 up: 75% to 97% (in 1% increments), *90%reduction direction: vertical/horizontal, *vertical only
2-on-1 record (ON/*OFF)
Mode Description
Chapter 1
1-16
1.2.3.8 Box Settings0015-4325
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory settings.**Indicated when the appropriate accessory is installed.
T-1-12
1.2.3.9 Printer Settings0015-4326
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
reception info record: keep/*do not keep
fax basic registration setup** register user telephone number**
telephone number: 20 characters max.
select line type**:
100V: *20 pps/10 pps/push
volume adjust
alarm volume: 0 to 8 (84)communication volume: 0 to 8 (*4)
off-hook alarm: (*ON/OFF)
fax transmission function setup** ECM transmission (*ON/OFF)
set pause length: 1 to 15 seconds (*2 seconds)
auto redial: (*ON/OFF)
number of redial sessions: 100V: 1-15(*2)interval of redial session (min): 2 to 99 (*2)redial at transmission error: 1st and error pages/all pages/off
pre-transmission dial tone check: (*ON/OFF)
fax reception function setup** ECM reception: (*ON/OFF)
select reception mode
*Automatic reception / modem dial-in FAX/TEL switchfax/tel switchover: at ring start: 0 to 30 sec (*8), ring length: 15 to 300 sec (*17), post-ring operation: end/*receive, voice answer: ON/*OFFauto receptionmodem dial-in fax/tel switchover
ring sound: ON (number of rings: 0 to n)/*OFF
remote reception: ON (remote reception ID: 00 to 99, *25)/*OFF
auto reception switchover: 1 to 99 seconds, *15 seconds)/*OFF
fax addition line setup** register user telephone number: 20 characters max.
register user abbreviation: 24 characters max.select type of line: *20 pps/10 pps/push
select transmission line: line 1: *priority on transmission/do not permit transmission line 2: priority on transmission/do not permit transmission
Mode Descriptionset/register user box select box: 0-99
register box name: 24 characters max(one-byte characters).ID No.: 0-9999999file auto delete: 0=none, 1, 2, 3, 6, 12 hr; 1, 2, *3, 7, 30 daysURL transmission setupPrint when saving data from the print driver: ON/*OFFreset
print photo mode (ON/*OFF)
read setup standard mode register/resetset/register fax box** select box: 0-49
register box name: 24 characters max(one-byte characters).ID No.: 0-9999999set URL transmissionreset
Mode Description
Chapter 1
1-17
*Factory settings.**Indicated in the presence of a specific accessory.
T-1-13
Mode Descriptionsettings number of copies: 1 to 9999 (*1)
duplex: duplex/*simplex
pickup
default paper size: *A4 (additional 10 possible)default paper type: plain (additional 8 possible)paper size replacement: replace/*do not replace
adjust print
**super smooth: *use/do not use**toner density: 1 to 9 (*5)toner save: enable/*disablethin line correction: *enable/DisableCorrection of horizontal lines: *Disable/Level 1/Level 2/Level 3/Level 4Correction of horizontal lines: *Disable/Level 1/Level 2/Level 3/Level 4Resolution: Super Fine/*Fine
layout
bind position: *Staple the long side/Staple the short sidebind margin: -50to+50mm (*0.0)Distance to move the stapling position in a direction of the short/long side (front/back): -50to+50mm (*0.0)
auto error skip**: skip/*do not skip
secure print delete time length: *1, 2, 3, 6, 12, 24 hr
timeout: 5 to 300 (*15 sec)/disable
RIP: yes/*no
sorter**: *do not use/sort/rotation sort/rotation group/shift sort/shift group/staple sort/Staple group
punch**: *disable/top/bottom/left/right
booklet print**: *disable/open to left/open to right
middle bind**: enable/*disable
**Correction of creep (displacement): *Disable/Automatic/Correction volume (0 to 10mm)
**Insert of the front cover: *Disable/Inserter 1/Inserter 2
**Fold: *Disable/Z-fold/C-fold
**transparency interleaf: *disable/white sheet/printed sheet
**print in sets
print in sets: enable/*disableprint position: *5 locations/upper left/lower left/upper right/lower right/Whole imageprint start character: 1 to 9999 (*1)print size: small at 12-point/medium at 24-point/*large at 36-pointdensity: 1 to 5 (*3)Adjustment of the printing position (vertical/horizontal): -8 to +8mm (*0)
Delivery side specification: *facedown/faceup
**printer operating mode: *auto (additional 9 settings possible)**priority emulation (*none/ additional settings possible)
**auto switchover
Chapter 1
1-18
1.2.3.10 Address Book Settings0015-4329
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.T-1-14
LIPS: *enable/disableN201: *enable/disableESC-P: *enable/disable15577: *enable/disableHP-GL: *enable/disableHP-GL/2: *enable/disableImaging: *enable/disablePDF1.5: *enable/disable
**connection recognition: *enable/disable
printer settings rest: yes/no
Mode Descriptionfax(register address)
register name: Japanese (2-byte zone only); 24 characterstelephone number: 120 characters max. (+ pause, tone, <, >, back space, space
ISDN sub address, F net, DT, R, PIN, detail setup)
detail setupF code: 20 characters max.password: 20 characters max.ECM transmission: *ON/OFFtransmission speed: 33600bps*/14400bps/9600bps/4800bpsline selection: line 1/line 2/*auto selectinternational transmission: domestic*/international 1/international 2/international 3communication mode: G4, G3*/G3 only
e-mail(register address)
register name: 24 characters, or 12 2-byte characters
register name: Japanese (2-byte zone only); 24 characters
e-mail address: 128 characters
i-fax(register address)
register address: 24 characters, or 12 2-byre characters
register name: Japanese (2-byte zone only), 24 characters
mode select: *Simple/Full
i-fax address: 128 characters
relay through server: ON/*OFFfixed sentence 1: 40 charactersfixed sentence 2: 16 charactersdetail setup
paper size: A4/LTR+ B4, A3/11x17compression method: MH+ MR/MMRresolution: 200x100dpi, 200x200dpi+200x400dpi/300x300dpi/400x400dpi/600x600dpi
file(register addresses)
register name: 24 characters, or 12 2-byte charactersregister name: Japanese (2-byte zone only), 24 characters
protocol: *FTP/Windows (SMB)/Netware (IPX)
host name: 128 characterspath to folder: 12* charactersuser name: FTP, NetWare (IPX); 24 characters Windows (SMB); 15 characters
password: FTP, NetWare (IPX); 24 characters Widows (SMB); 14 characters
group(register address)
register name: 24 characters, or 12 2-byte characters
register name: Japanese (2-byte zone only), 24 characters
address book: select from following already registered in address book: fax, e-mail, i-fax, remote file system, jet SEND, box, local printer
save in box: select box: 00 to 99
delete
Mode Description
Chapter 1
1-19
1.2.3.11 Voice Guide Settings0015-4331
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
*Factory default.T-1-15
1.2.4 Maintenance by the User
1.2.4.1 Cleaning0015-5258
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine requires cleaning by the user from time to time. Advise the user to perform the following work on a periodical basis (e.g., at least once a month):
1. Platen BoardClean the platen board cover [1] with a cloth moistened with water or solution of mild detergent (well-wrung); then, dry wipe it with a soft, dry cloth.
F-1-11
2. Platen RollerClean the platen roller [1] with a cloth moistened with water or solution of mild detergent (well-wrung); then, dry wipe it with a dry, soft cloth.
search for address(server)
simple search
server to search: from pull-down from LDAP server already registered
(search conditions): name: 128 characters, or 64 2-bye characters e-mail: 12* characters fax: 128 characters
detail searchserver to search: from pull-down from LDAP server already registered
(search conditions): *name/e-mail/fax/group/group unit under following: * includes next/does not include next/is identical to next/is not identical to next/start with next/ends with nextname, group, group unit: 128 characters, or 64 2-byte characterse-main, fax: 128 characters
(condition combination): *or/and
search result
register type: *all e-mail/fax
register e-mail for i-fax: ON/*OFF (toggle)register name of address book register name: 16 characters
register one-touch button register/edit address: register/edit, delete
one-touch name: 12 characters max.
Mode Descriptionvoice guide reading volume/speed volume: 1 to 5* to 9
speed: (slow) -5 to 0* to +5 (fast)
voice type male/female*
speaker/headphone switch speaker*/headphone
auto clear in voice guide ON/OFF*
initialize voice guide settings Is it OK to initialize? yes/no
Mode Description
[1]
Chapter 1
1-20
F-1-12
3. Platen Board Glass/ADF Reading GlassWipe the platen board glass [1] and the ADF reading glass [2] with a cloth moistened with water or solution of mild detergent; then, dry wipe them with a dry, softcloth.
F-1-13
4. ADF Glass Retainer/Paper Guide BaseWipe the ADF glass retainer [1] and the paper guide base [2] with a cloth moistened with water or solution of mild detergent; then, dry wipe them with a dry, softcloth.
F-1-14
5. Vertical Size PlateWipe the vertical size plate [1] with a cloth moistened with waste or solution of mild detergent; then, dry wipe them with a dry, soft cloth.
F-1-15
1.2.4.2 Checks0015-5260
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine is equipped with a breaker used to check for over-current and leakage current, requiring the user to check the operation of the breaker on a periodicalbasis (e.g., at least once a month). Also, ask the user to keep a record of checks made.How to Check the Breaker.1) Turn on the main power switch.2) Press the test button [1] of the breaker using the tip of a ball-point pen or the like.
[1]
[1][2]
[1] [2]
[1]
Chapter 1
1-21
F-1-163) Check to see that the breaker switch [1] has shifted to the OFF position, thus cutting off the power.
F-1-174) Turn off the main power switch.5) Shift the breaker switch [1] back to the ON position.
F-1-18
Advise the user that the breaker switch is fully to the ON position. If it is found between ON and OFF positions, it must first be shifted to the OFF position and thento ON.
6) Turn off the main power switch.
1.2.5 Safety
1.2.5.1 Safety of the Machine's Laser Unit0015-4333
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Often, laser light can prove to be harmful to the human body. The machine's laser scanner unit is shielded in a protective housing and by external covers so that itslight will not escape outside the machine as long as the machine is used in normal operating conditions.
1.2.5.2 CDRH Regulations0015-4335
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The Center for Devices and Radiological Health of the US Food and Drug Administration put into forth regulations intended for laser products. Under the regula-tions, laser products that are produced on and after August 1, 1976, may not be sold within the US unless they are appropriately certified. The following is a labelissued to certify compliance with the regulations and must be found on all laser products sold in the US.
ON(I side)
OFF(Oside)
[1]
ON(I side)
OFF(O side)
Chapter 1
1-22
F-1-19
The text of the label may differ from model to model.
1.2.5.3 Handling the Machine's Laser Unit0015-4337
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure to observe the following whenever you are planning to service the areas around the machine's laser unit:- Do not put a screwdriver or the like that has a high rate of reflection into the laser path.- Remove watches and rings before starting the work to avoid reflection of laser light to the eye.
The machine's laser light is red, and its covers that may reflect laser light are identified by a warning label shown below. If you must detach a cover in the field toservice the machine, be sure to exercise extra care. (Keep in mind that the machine's laser unit cannot be adjusted in the field.)
F-1-20
1.2.5.4 Safety of Toner0015-4339
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's toner is a non-toxic material consisting of plastic, iron, and small amounts of colorings.If your skin or clothes have come into contact with toner, remove as much toner as possible using dry paper tissue, and wash with water. Do not use warm or hotwaster; otherwise, the toner will jell and fuse permanently with the fibers of the clothes. Also, do not bring toner into contact with vinyl, as it tends to react.
Do not throw toner into fire. An explosion can occur.
1.2.6 Product Specifications
1.2.6.1 Product Specifications0015-4300
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Chapter 1
1-23
Copyboard stream reading, fixed readingBody consoleLight source type xenon lamp (yellow green)Lens type fixed focusPhotosensitive medium A-Si drum (80-mm dia.)Image reading method light-receiving element (1 line CCD), CISReproduction method indirect electrostaticExposure method laser lightCopy density adjustment function
auto or manual
Charging method coronaDevelopment method dry, 1-component toner projectionTransfer method Static transferSeparation method static separationPickup method from cassette, manual feeder, paper deckCassette pickup method separation retardPaper deck pickup method separation retardMultifeeder pickup method separation retardDrum cleaning method Cleaning bladeFixing method Heat roller fixing (H method)Delivery method face-down, face-upToner level detection function yesToner type Magnetic negative toner Toner supply type Toner bottle replacementOriginal type sheet, book, 3-D object (2 kg max.)Maximum original size 304.8mm x 432mmOriginal size detection function main scanning: CCD size detection
sub scanning: reflective document sensorReproduction ratio 100% (1:1), reduce (1:0.250, 1:0.500, 1:0.611, 1:0.707, 1:0.816,
1:0.865), enlarge (1:1.154, 1:1.224, 1:1.414, 1:2.000, 1:4.000), between(1:0.250 to 4.000) (25% and 400%, in 1%-increments)
Warm-up time 30sec or lessMaximum non-image width (main scanning direction)
2mm or less
Maximum non-image width (sub scanning direction)
2mm or less
Image margin (leading edge) 4.0+1.5/-1.0mmImage margin (trailing edge) 2.0±1.5mmImage margin (left/right) left: 2.5±1.5mm (2nd side: 2.5±2.0mm), right: 0.5mm or more Non-image width (leading edge) 4.0+1.5/-1.0mmNon-image width (trailing edge) 2.0±1.5mmNon-image width (left/right) 2.5±1.5mmNumber of gradations 256 gradationsReading resolution 600dpi x 600dpiCopying resolution 600dpi (equivalent) x 600dpi,1200dpi (equivalent) x 600dpi,2400dpi
(equivalent) x 600dpiPrinting resolution 1200dpi (equivalent) x 1200dpi First copy time iR5075N:
3.1seciR5065 / iR5065N / iR5055 / iR5055N :3.3sec
Cassette capacity 1200 sheets (64g/m2), 1100 sheets (80g/m2)Multifeeder tray capacity 50 sheets (64, 80g/m2)Paper deck capacity 3400 sheets (64g/m2), 3000 sheets (80g/m2)Duplex method Through-pass method/StacklessDelivery tray stack Copy tray: 250 sheets (80g/m2)
Shift tray: 500 sheets (80g/m2)Continuous reproduction 1 - 999Memory 1GBOperating environment (temperature range)
15 to 27.5 deg C
Operating environment (humidity range)
25 to 75%
Operating environment (atmospheric pressure)
0.6 to 1.0 atm
Noise standby: 58 dB or less, printing: 75 dB or lessHard disk 40GBPower supply rating 100V 15A/ 120V 20A/ 230V 10ASleep mode yes
Chapter 1
1-24
1.2.7 Function List
1.2.7.1 Paper Types0015-4301
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-1-16
1.2.7.2 Printing Speed0015-4302
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-1-17
Power consumption (maximum) 1500W (100V), 1920W (120V), 2300W (230V)Power consumption continuous printing (100V, 50Hz, w / accessories ) : 923 Wh (reference
only)Ozone Initial: 0.01ppm or less (avr), Later (after 500,000 pages): 0.035 ppm or
less (avr)Dimensions 643mm(W) x 743mm(D) x 1207mm(H)(Including an ADF)
* Only for Japan (with a capacitor): 643mm(W) x 839mm(D) x1207mm(H)(
Weight 220kg ((Including an ADF and toner bottle)* Only for Japan (with a capacitor): 230kg
Type Paper sizePaper feeding position
Cassette Deck (left/right) Manual feed 3.5 side paper
deck3.5 large
paper deckPlain paper (60 to 90g/m2)Recycled paperColored paperEnvironment paper3-hole paper4-hole paper
A4,B5,LTR yes yes yes yes yesA3,B4,LDR,LGL yes no yes no yesA4R,LTRR yes no yes no yesB5R yes no yes no noA5R,STMTR yes no yes no noA5,STMT no no no no no
Thick paper (91 to 200g/m2)Bond paper
A4,B5,LTR yes yes yes yes yesA3,B4,LDR,LGL yes no yes no yesA4R,LTRR yes no yes no yesB5R yes no yes no noEXEC no no yes no noA5R,STMTR yes no yes no noA5,STMT no no no no no
Special paper
OHP film A4,A4R,LTR,LTRR no no yes no noPostcard A4R deformed, Double postal card, Four-
face postcard no no yes no no
Label A4,A4R,B4,LTR,LTRR no no yes no noIndex (tab) paper A4,LTR
yes no no no no
Tracing paper A3,B4,A4R,A4,B5R,B5 no no yes no no
Classification Paper size
E232 E232A E232BSingle-sided Double-sided Single-sided Double-sided Single-sided Double-sided
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Plain paperColored paper
Recycled paperEnvironment
paper3-hole paper4-hole paper
A4 75 53 37 26 65 46 32 23 55 46 27 23B5 75 53 37 26 65 46 32 23 55 46 27 23A5R 35 35 17 17 35 35 17 17 35 35 17 17B5R 63 47 31 23 55 41 27 20 46 41 23 20A4R 54 44 27 21 47 38 23 19 40 38 20 19B4 45 38 22 19 39 33 19 16 39 33 19 16A3 37 33 18 16 32 29 16 14 32 29 16 14LTR 75 53 37 26 65 46 32 23 55 46 27 23STMTR 35 35 17 17 35 35 17 17 35 35 17 17LTRR 58 45 28 22 50 39 25 19 43 39 21 19LGL 45 38 22 19 39 33 19 16 39 33 19 16LDR 37 33 18 16 32 29 16 14 32 29 16 14
Chapter 1
1-25
*1: "Deck/cassette feed" includes feeding by the side paper deck.
1.2.7.3 Paper Types/Printing Speed (K paper)0015-8283
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-1-18
Thick paper
A4 63 53 31 26 55 46 27 23 55 46 27 23B5 63 53 31 26 55 46 27 23 55 46 27 23A5R 28 28 14 14 28 28 14 14 28 28 14 14B5R 53 47 26 23 46 41 23 20 46 41 23 20A4R 46 44 23 21 40 38 20 19 40 38 20 19B4 38 38 19 19 33 33 16 16 33 33 16 16A3 31 31 15 15 27 27 13 13 27 27 13 13LTR 63 53 31 26 55 46 27 23 55 46 27 23STMTR 28 28 14 14 28 28 14 14 28 28 14 14LTRR 50 45 24 22 43 39 21 19 43 39 21 19LGL 38 38 19 19 33 33 16 16 33 33 16 16LDR 31 31 15 15 27 27 13 13 27 27 13 13
Bond paperLTR 35 35 17 17 30 30 15 15 30 30 15 15LTRR 24 24 12 12 21 21 10 10 21 21 10 10EXEC - 35 - - - 30 - - - 30 - -
Tracing paper
A4 - 53 - - - 46 - - - 46 - -B5 - 53 - - - 46 - - - 46 - -B5R - 47 - - - 41 - - - 41 - -A4R - 44 - - - 38 - - - 38 - -B4 - 38 - - - 33 - - - 33 - -A3 - 31 - - - 27 - - - 27 - -
OHP
A4 - 53 - - - 46 - - - 46 - -A4R - 44 - - - 38 - - - 38 - -LTR - 53 - - - 46 - - - 46 - -LTRR - 45 - - - 39 - - - 39 - -
Postcard
Postcard - 15 - - - 15 - - - 15 - -Double postal card - 28 - - - 28 - - - 28 - -
Four-face postcard - 53 - - - 46 - - - 46 - -
LabelA4 - 53 - - - 46 - - - 46 - -A4R - 44 - - - 38 - - - 38 - -B4 - 38 - - - 33 - - - 33 - -
Tab paperA4 59 - - - 51 - - - 51 - - -LTR 59 - - - 51 - - - 51 - - -
Type Paper sizePaper feeding position
Cassette Deck (left/right) Manual feed 3.5 side paper
deck3.5 large
paper deckPlain paper (60 to 90g/m2)Recycled paperColored paperEnvironment paper3-hole paper4-hole paper
A4,B5,LTR yes yes yes yes yesA3,B4,LDR,LGL yes no yes no yesA4R,LTRR yes no yes no yesB5R yes no yes no noA5R,STMTR yes no yes no noA5,STMT no no no no no
Thick paper (91 to 200g/m2)Bond paper
A4,B5,LTR yes yes yes yes yesA3,B4,LDR,LGL yes no yes no yesA4R,LTRR yes no yes no yesB5R yes no yes no noEXEC no no yes no noA5R,STMTR yes no yes no noA5,STMT no no no no no
Classification Paper size
E232 E232A E232BSingle-sided Double-sided Single-sided Double-sided Single-sided Double-sided
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Deck cassette feed *1
Multi manual
feed
Chapter 1
1-26
Special paper
OHP film A4,A4R,LTR,LTRR no no yes no noPostcard A4R deformed, Double postal card, Four-
face postcard no no yes no no
Label A4,A4R,B4,LTR,LTRR no no yes no noIndex (tab) paper A4,LTR
yes no no no no
Tracing paper A3,B4,A4R,A4,B5R,B5 no no yes no no
Type Paper sizePaper feeding position
Cassette Deck (left/right) Manual feed 3.5 side paper
deck3.5 large
paper deck
Chapter 2 Installation
Contents
Contents
2.1 Making Pre-Checks........................................................................................................................................................2-12.1.1 Selecting the installation space .................................................................................................................................................... 2-12.1.2 Combination Table of Accessories .............................................................................................................................................. 2-2
2.2 Unpacking and Installation ............................................................................................................................................2-32.2.1 Unpacking and installation procedure ......................................................................................................................................... 2-32.2.2 Unpacking .................................................................................................................................................................................... 2-32.2.3 Installation of Scanner ................................................................................................................................................................. 2-42.2.4 Installation of Fixing Assembly................................................................................................................................................... 2-52.2.5 Checking of Charging Assembly and Dustproof Glass .............................................................................................................. 2-62.2.6 Installation of Developing Assembly .......................................................................................................................................... 2-72.2.7 Installation of Pickup Assembly ................................................................................................................................................. 2-82.2.8 Attaching Deck Pressure Plate .................................................................................................................................................... 2-82.2.9 Setting Toner Container .............................................................................................................................................................. 2-92.2.10 Connecting the Cable ................................................................................................................................................................. 2-92.2.11 Checking the Environment Switch .......................................................................................................................................... 2-102.2.12 Attaching the Label.................................................................................................................................................................. 2-102.2.13 Turning On the Main Power Switch ........................................................................................................................................ 2-112.2.14 Toner Stirring........................................................................................................................................................................... 2-112.2.15 Media Cassette Settings ........................................................................................................................................................... 2-112.2.16 Index Paper Attachment........................................................................................................................................................... 2-112.2.17 Changing the Media Size of the Front Deck (Left/Right) ....................................................................................................... 2-122.2.18 Image/Operation Check in User Mode .................................................................................................................................... 2-122.2.19 Adjustment of Image Left End Margin.................................................................................................................................... 2-122.2.20 Adjustment of image leading edge margin .............................................................................................................................. 2-142.2.21 Mounting of the Host Machine ................................................................................................................................................ 2-14
2.3 Checking the Connection to the Network ....................................................................................................................2-162.3.1 Overview.................................................................................................................................................................................... 2-162.3.2 Checking the Connection to the Network.................................................................................................................................. 2-162.3.3 Using the Ping Command .......................................................................................................................................................... 2-172.3.4 Making a Check Using the Remote Host Address..................................................................................................................... 2-17
2.4 Troubleshooting the Network ......................................................................................................................................2-172.4.1 Troubleshooting the Network ................................................................................................................................................... 2-172.4.2 Checking the Connection of the Network Cable ...................................................................................................................... 2-172.4.3 Making a Check Using a Loopback Address ............................................................................................................................ 2-172.4.4 Making a Check Using a Local Host Address .......................................................................................................................... 2-17
2.5 Installing the Copy Tray ..............................................................................................................................................2-172.5.1 Confirming the contents............................................................................................................................................................. 2-172.5.2 Power off of the host machine ................................................................................................................................................... 2-182.5.3 Installation procedure................................................................................................................................................................. 2-18
2.6 Installing the Card Reader............................................................................................................................................2-212.6.1 Notice At Installation................................................................................................................................................................. 2-212.6.2 Confirming the contents............................................................................................................................................................. 2-212.6.3 Power off of the host machine ................................................................................................................................................... 2-222.6.4 Installation procedure................................................................................................................................................................. 2-222.6.5 Installing for imageWARE Accounting Manager ..................................................................................................................... 2-25
2.7 Installing the Original Holder ......................................................................................................................................2-252.7.1 Checking Contents .................................................................................................................................................................... 2-252.7.2 Installation Procedure ............................................................................................................................................................... 2-262.7.3 Checking Contents .................................................................................................................................................................... 2-272.7.4 Installation Procedure ............................................................................................................................................................... 2-27
Contents
2.8 Installing the Reader Heater ........................................................................................................................................ 2-282.8.1 Checking the Contents ............................................................................................................................................................... 2-282.8.2 Power off of the host machine ................................................................................................................................................... 2-282.8.3 Installation Procedure ................................................................................................................................................................ 2-29
2.9 Installing the Cassette Heater ...................................................................................................................................... 2-322.9.1 Checking Components ............................................................................................................................................................... 2-322.9.2 Power off of the host machine ................................................................................................................................................... 2-332.9.3 Installation Procedure of the Cassette Heater ............................................................................................................................ 2-33
2.10 Installing the Deck Heater ......................................................................................................................................... 2-382.10.1 Checking the Parts to Install .................................................................................................................................................... 2-382.10.2 Turning Off the Host Machine................................................................................................................................................. 2-39
2.11 Installing the Deck Heater (Large Deck) .................................................................................................................. 2-392.11.1 Checking the Parts to Install .................................................................................................................................................... 2-392.11.2 Turning Off the Host Machine................................................................................................................................................. 2-40
2.12 Installing the Voice Guidance Kit ............................................................................................................................. 2-402.12.1 A point to keep in mind at installation..................................................................................................................................... 2-402.12.2 Checking the Contents ............................................................................................................................................................. 2-402.12.3 Power off of the host machine ................................................................................................................................................. 2-412.12.4 Installation Procedure .............................................................................................................................................................. 2-41
Chapter 2
2-1
2.1 Making Pre-Checks
2.1.1 Selecting the installation space0015-4647
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The conditions of the installation space include the following.Preliminary inspection of the planned installation space would be desired before shipping the machine to the customer.1. The power supply can be connected to a power outlet of 100 V -/+ 10 V, 15 A or more. The host machine can be grounded.
Grounding target1) Grounding terminal of power outlet2) Grounding terminal finished to category D
2. The temperature and humidity are within the range shown in the following figure. The area near the faucet, water heater, moisture chamber and refrigerator shouldbe especially avoided.
F-2-1<Assured environmental zone>[A]: A zone. All quality standard items are satisfied.[B]: B zone. Some quality standard items are inferior to those in A zone or not satisfied.[C]: C zone. Copying operation is performed normally without any safety issues, malfunction, and errors in display.3. The area near the origin of fire, with full of dust and where ammonia gas generates should be avoided. In the case that the space is exposed to direct light, it is
better to hang a curtain on the window.4. Although the ozone level generating in using this equipment does not affect human bodies, long-hours operation in a poorly-ventilated room may cause some
odor to be sensed. Ventilation should be done to keep a comfortable work environment.5. The foot of the host machine should not get off the floor. The host machine should be kept in a horizontal status.6. The host machine should be separated from the wall by 100 mm or more to keep a space sufficient for machine operation.- When installing the Copy Tray-L1
F-2-2- When installing the Saddle Finisher-AD2 + Paper Folding Unit-E1 + Document Insertion Unit-E1 + Puncher Unit-AS1 + Paper Deck-AE1
100(%RH)
(degC)
90
85
75
70
50
20
25
1510
5
0 10
7.5 23 27.5 32.5
15 20 25 30 35 40
[A]
[B]
[C]
500mm 500mm
500mm
1,448 mm
100 mm or more
1,27
8 m
m
13,7
4 m
m
Chapter 2
2-2
F-2-37. This equipment should be installed in a well-ventilated room, however not near the ventilating suction mouth in the room.8. In the case that several machines are installed at the same area, this machine should be arranged so that this machine does not draw directly the exhaust air from
the other machines. The life of the charging wire may be shortened, especially in a low-humidity environment.
F-2-4
2.1.2 Combination Table of Accessories0015-7973
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-2-1
The following table shows the combination of accessories that are set at the right side of the host machine. When setting the accessories indicated in the table, refer to the table below and check the combination before the setup.
Document Tray Voice Guidance Kit Card Reader
Document Tray- no yes
Voice Guidance Kitno - yes
Card Readeryes yes -
yes: Available no: Unavailable
2,482 mm
2,591 mm109 mm
1,27
8 m
m
1,37
4 m
m
500mm
500mm
500mm
100 mm or more
Chapter 2
2-3
2.2 Unpacking and Installation
2.2.1 Unpacking and installation procedure0015-4653
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Take into account the following points when installing this equipment.
2.2.2 Unpacking0015-4654
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Unpack the package, and remove the vinyl.2) Open the attached cardboard box, and then insert the 1 grip [1] that has
been included to the front of the pickup side.
F-2-5
3) Hold the 2 grips (front/rear) on the pickup assembly side [1] of the hostmachine, and then remove the 2 pads [2] while lifting the host machine alittle. (Mass of the host machine: Approx. 230 kg)
F-2-64) Hold the 2 grips (front/rear) on the delivery assembly side [1] of the host
machine, and then remove the 2 pads [2] and the vinyl bag while liftingthe host machine a little.
1. When transferring the host machine from a low-temperature to a warm place and installing it, dew condensation may occur around the pickup/feed assembly, leading to image faulty reproduction. Therefore, the host machine is unpacked and left for 1 hour or more to make it accustom to room temperature (Dew condensation: The phenomenon where water drops accumulate on the surface of metal when a metal material is moved from a low-temperature to a warm area and the moisture in the air surrounding the metal is quickly cooled)
2. When using stairways for carrying in and out from/to the installation space, take into account the following points.
1) When lifting the host machine, do not use the left and right grips (3 locations) but hold the four corners at the bottom of the host machine.2) The mass of this equipment is approx. 230 kg. Make sure that four persons perform unpacking.3) Remove the ADF assembly, the fixing feed unit assembly and the duplexing unit assembly, and then separate them from the host machine before carrying in and out.
Be sure to insert the leaf spring of the grip downward. Adverse insertion may cause the grip coming off while lifting the host machine.
[1]
[1]
[2]
Chapter 2
2-4
F-2-75) Remove the cardboard on the skid, and then take out the 2 slope plates in-
stalled at the center of the skid.
6) Reverse the slope plate [1]. Match the pin hole of the skid against the pinhole of the slope plate, and then insert the 2 pins [2].
F-2-87) Hold the grip [1] of the host machine. Slide the host machine on the slope
to get it down from the skid.
F-2-98) Remove the grip [1] while pressing the leaf spring with a flathead screw-
driver.
F-2-109) Remove the packing tape attached onto the host machine.
2.2.3 Installation of Scanner0015-4657
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the DADF, and remove the packing materials. 2) Remove the scanner fixing screw [1].
If the slope plate is difficult to remove, displacement of the host machine to the rear edge of the skid makes operation easier.
Be careful that the caster [2] does not fall out from the skid.
[1]
[2]
[1]
[2]
[2]
[1]
[1]
[1]
Chapter 2
2-5
F-2-11
3) Pull the release lever [1] and open the white sheet [2] in the direction ofthe arrow [A].
F-2-124) Remove the protection sheet.
F-2-13T-2-2
5) Close the white sheet.6) Close the DADF.
2.2.4 Installation of Fixing Assembly0015-4659
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover. 2) Shift the fixing/feeder assembly release lever [1] in the direction of the ar-
row, and release the transfer/separation charging assembly. Slide the fix-ing/feeder unit [2] out toward the front.
F-2-143) Remove the separation claw release member [1] and tag [2] attached onto
the fixing/feeder assembly.
F-2-154) Peel off the tag tape to open the fixing/delivery assembly [1].
F-2-165) Remove the 2 fixing nip pressure release screws [1].
The scanner fixing screw will be used when relocating the machine; thus, make sure a user stores away it.
After the host machine is installed, if moving the machine elsewhere, put the protection sheet.If not, the image may be affected.
[1]
[1][2]
[A]
[1]
Make sure to remove the foreign particles, such as tape glue, from the surface of the feeder belt.
[1] [2]
[1][2]
[1]
Chapter 2
2-6
F-2-176) Close the fixing/delivery assembly.
2.2.5 Checking of Charging Assembly and Dustproof Glass
0015-4660
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the feeder assembly front cover (right) [1]. - 2 screws [2]
F-2-182) Remove the screw [1] and the mount [2], and disconnect the connector [3].
F-2-193) While holding the front and rear sides of the transfer/separation charging
assembly [1], slide it in the [A] direction; then, remove it toward the [B]direction.
F-2-204) Check the transfer/separation charging assembly. If any dirt or paper pow-
der is attached onto the assembly, clean it with alcohol solutions. 5) Mount the transfer/separation assembly using the steps to remove it but in
reverse. 6) Attach the feeder assembly front cover (right) with the 2 screws (use the
screws removed in the step 1). Put back the fixing/feeder assembly andthe duplexing unit to the original positions (leave the fixing/feeder assem-bly release lever as it is).
7) Open the toner replacement cover. 8) Detach the toner replacement cover [1].
- 2 screws [2]
F-2-219) Detach the connector cover [1].
- 1 screw [2]
F-2-2210) Remove the 2 screws [1] and disconnect the connector [2]; then, remove
the primary fan duct [3].
[1]
[1]
[2]
[2]
[1]
[1][2]
[3]
Be careful not to cut the nylon wire by contacting the transfer/separation charging assembly with the transfer guide.
[1]
[A]
[B]
[2] [2]
[1]
[2][1]
Chapter 2
2-7
F-2-2311) Loosen the screw [1] and shift the charging assembly mount [2] in the
direction of the arrow; then, tighten the screw once again. 12) Disconnect the connector [3], and remove the primary charging as-sembly [4].
F-2-2413) Check the primary charging assembly. If any dirt or paper powder is at-
tached onto the assembly, clean it with alcohol solutions. 14) Disconnect the connector [1] and remove the screw [2]; then, slide the
pre-transfer charging assembly [3] out.
F-2-2515) Check the pre-transfer charging assembly. If any dirt or paper powder is
attached onto the assembly, clean it with alcohol solutions. 16) Remove the dustproof glass [1].
F-2-2617) Check and clean the dustproof glass with a blower brush.
18) Mount the primary charging assembly, the pre-transfer charging assem-bly, and the dustproof glass; then, fix them using the steps to remove thembut in reverse.
19) Attach the primary fan duct and the toner replacement cover using thesteps to remove them but in reverse.
20) Lock the fixing/feeder assembly release lever, and close the front cover.
2.2.6 Installation of Developing Assembly 0015-4661
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the upper right cover [1], and remove the screw [2] from the doortape; then, open the cover further.
Do not make the screws fall off.T-2-3
F-2-272) Remove the tape [1], and detach the hopper supply mouth cover [2].
[1]
[2]
[3]
[3] [4] [2][1]
[1][2] [3]
[1]
1. In case of using solutions for cleaning, be sure that the solutions are completely dried out.
2. When inserting the pre-transfer charging assembly, slide it in horizontally against the process unit for not to scratch the surface of the drum.
3. Make sure that the one-way arm of the pre-transfer charging assembly is placed onto the eccentric cam.
Be sure to connect the connector when attaching the primary fan duct.
Do not make the screws fall off.
[1][2]
Chapter 2
2-8
F-2-283) Take out the developing assembly from the packing box. 4) Rotate the developing cylinder gear with hand, and check for scratch on
the surface of the cylinder. 5) Mount the developing assembly [1] by holding the center (pocket for grip)
of it. Then, connect the connector [2].
F-2-296) Fit the developing assembly pressure unit [1] to [2], and slide it in hori-
zontally in the [A] direction; then, shift toward the [B] direction. - 1 screw (binding; M4X6) [2]
F-2-30
2.2.7 Installation of Pickup Assembly 0015-4662
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the pickup roller pressure release spacer [1].
F-2-312) Slide the right deck and Cassett3/4 halfway out, and open the lower right
cover. Then, remove the pickup roller pressure release spacers [1].
F-2-323) After removing all spacers, slide the deck/cassette in and close the lower
right cover. 4) Attach the door tape of the upper right cover with the screw, and close the
upper right cover.
2.2.8 Attaching Deck Pressure Plate 0015-4663
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Press the release button of the left deck and slide the left deck out. 2) Attach the deck pressure plate [1] with the screw (RS tightening; M4X8)
When mounting the developing assembly, be sure not to contact the developing cylinder with the developing assembly mounting plate.
[2]
[1]
[1]
[2]
[1][3]
[A]
[B] [2]
Remove the pickup roller pressure release spacer [1] while moving the front side of it upward after sliding the spacer toward the right.
MEMO;The spacers are being pressured while the deck/cassette is set; thus, it is hard to remove them. Therefore, release the pressure by sliding the deck/cassette halfway out.
[1]
[1]
[1]
Chapter 2
2-9
[2].
F-2-333) Close the left deck.
2.2.9 Setting Toner Container 0015-4664
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Take out the toner container from the packing box. 2) After opening the toner replacement cover [1], pull down the lock lever[2] in the direction of the arrow.
F-2-343) Hold the toner container [1] as shown in the figure below, and remove the
cap [2] from the container by rotating the cap in the direction of the arrow.
F-2-354) Hold the toner container with its mouth [1] at the right side, and set it into
the supply case [2] of the host machine horizontally.
F-2-365) Slide the lock lever [1] upward to lock the toner container [2] in place.
F-2-376) Close the toner replacement cover.
2.2.10 Connecting the Cable0015-4665
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Attach the wire saddle [1] onto the upper rear cover.
F-2-382) Connect the 2 connectors [1] of the reader communication cable, and then
fix the cable in place with the wire saddle [2].
Do not shake the toner container. If setting the toner container that has been shaken to the host machine, the toner overflow within the machine may occur. By shaking the container, the toner fluidity increases. As a result, toner is supplied swiftly to the machine with the toner supply operation, causing the foregoing symptoms.
[1] [2]
[1] [2]
[1]
[2]
When turning on the main power switch without setting toner container, the toner level meter on the control panel shows 25 % or less. Make sure that the toner container is set in the host machine before turning on the main power switch.
[1]
[2]
[2]
[1]
[1]
Chapter 2
2-10
F-2-393) Connect the connector [1] of the ADF power supply cable.
F-2-404) Connect the 2 connectors of the ADF communication cable.
F-2-41
2.2.11 Checking the Environment Switch0015-4667
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Make settings for environment switch [1] and the cassette heater switch[2] according to the environment of the installation site. In case the drum/cassette heaters are required to be turned on while the main power switchis turned off, make the settings with the following 2 switches:
F-2-42
2.2.12 Attaching the Label0015-9830
iR5065 / iR 5055 / iR5075 / iR5065N / iR5055N
<Attaching the cleaning position label>1) Open the DADF [1].1) Attach the cleaning position label [2] for the relevant language.
F-2-43<Attaching the cleaning procedure label>1) Pull the release lever [1] and open the white sheet [2] in the direction of
the arrow [A].
F-2-442) Attach the cleaning procedure labels [1] [2] for the relevant language.
Drum heater
ON OFF
Environment switch ONMain power switch ON
Environment switch OFFMain power switch OFF
Cassette heater
ON OFF
[1]
[2]
[1]
[1]
Cassette heater switch ONEnvironment switch ONMain power switch OFF
Cassette heater switch OFFEnvironment switch ONMain power switch ON
ON
[1]
[2]
[2]
[1]
[1][2]
[A]
Chapter 2
2-11
F-2-453) Remove the reading cleaning tool [1].
F-2-464) Attach the cleaning procedure label [1] for the relevant language.
F-2-475) Put the detached parts back on by reversing the foregoing steps.
- Reading cleaning tool- White sheet
6) Close the DADF.
2.2.13 Turning On the Main Power Switch0015-4668
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) In the case of 100V machine, ground the host machine with the groundingwire.Targets of Grounding1. Grounding terminal of power outlet2. Grounding terminal of which grounding work (D Type) is properlydone.
2) Slide the duplexing unit out, and check to see that there is no foreign sub-stances or damage in the unit.
3) Make sure that the main power switch is turned off, and then connect thepower plug into the power outlet.
4) Turn on the main power switch.- The message 'Wait..' appears.
2.2.14 Toner Stirring0015-4669
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
After wait time, execute toner supply in service mode.1) Enter service mode.2) Select: COPIER > FUNCTION > INSTALL > TONER-S.3) Check the message 'CHECK THE DEVELOPER' appears.4) Check to see that the developing assembly is attached appropriately, and
then press 'OK'.
- It takes approx. 8 to 10 minutes to supply toner. The machine stopsautomatically after counting.- Make settings for the cassette until the completion of toner supply. (Seemedia cassette settings.)
5) Press [Reset] to escape from service mode.
2.2.15 Media Cassette Settings0015-4671
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Hold down the cassette release button to slide each cassette to the front.2) Set the side guide [1] of each cassette onto the hole of the mark M [2] (A4/
A3).
F-2-483) Attach the inch-series block from inside the cassette onto the hole of the
mark A [1] (STMT-R) and the hole of the mark H [2] (LTR-R) so thatthey are hidden.
F-2-494) Close each cassette.
2.2.16 Index Paper Attachment0015-4673
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Determine the cassette for index paper from either of Cassette 3 or 4. Pressthe release button of the cassette you determined to slide it toward thefront. Fit the 2 one-touch supports [1] onto the holes [2] of the cassette,and press the pin into the hole to fix them in place.
2) Fit the holes of the index paper attachment [3] on the one-touch supports[1].
3) Set the base sheet [4] on the cassette.
Be sure to remove the packaging materials inside the cassette before turning on the main power switch.
[1]
[2]
[1]
[1]
Be sure not to turn off the machine during its operation.
-Be sure to attach the inch-series block firmly.-Go through this procedure only in case of not using inch-series paper.
[1]
[2]
[1]
[2]
Chapter 2
2-12
F-2-504) Close the cassette.
2.2.17 Changing the Media Size of the Front Deck (Left/Right)
0015-4674
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Hold down the release button to slide the deck out.2) Remove the screw [4] of the trailing end plate [1], the left guide plate [2],
and the right guide plate [3] respectively, and secure each plate in placeat the position of the size that user wishes.Default setting: A4 sizeAfter setting the size, set the deck into the host machine.
F-2-513) Attach the new media size label onto the media size plate of the deck.4) In case the size is changed, register the front deck media size in service
mode.Right deck: COPIER > OPTION > CST > P-SZ-C1Left deck: COPIER > OPTION > CST > P-SZ-C2A4=6, B5=15, and LTR=18
2.2.18 Image/Operation Check in User Mode0015-4675
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Press [Reset] twice and return to the main screen. Using test sheet, checkthe copy operation and copy image.- Copy operation: Check to see that the copy operation is appropriate.
- Duplexing copy operation: Check to see that the paper feeding at theduplexing unit is appropriate.- Pickup operation: Check to see that paper pickup from each sourceof paper is appropriate.- Operation noise: Check to see that there is no abnormal sound.- Fixed ratio reproduction: Check the image quality for each fixed ratioreproduction.- Multiple copies: Check to see that the copy operation for a specifiednumber of sheets is appropriate.- Check to see that print images picked up from each cassette/deck arewithin the scope of specifications.
Specification for image left end margin: 2.5 -/+1.5mmSpecification for image leading edge margin: 4.0-1.5/-1.0mmIn case the values is/are out of the scope of the specifications, see'Adjustment of image left end margin' and 'Adjustment of image leadingedge margin'.
* In case there is a difference in density between the left and the right of theimage, adjust the height of the primary charging wire at the rear side tocorrect it.
2) At customer's desire, set the standard mode from user mode or servicemode.
3) Place media in the right/left decks.4) Close the right/left decks. Tear off the relevant media size label [1] from
the mount sheet, and then attach it onto the media size plate of the deck.
F-2-525) Hold down the release button, and then slide Cassette3 and 4 out.6) Tear off the relevant media size label [1] from the mount sheet, and attach
it onto the media size plate [2] of the cassette. Set the media size plate inthe cassette.
F-2-537) Close each cassette.
2.2.19 Adjustment of Image Left End Margin0015-4676
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Cassette 3/4>1) Hold down the cassette release button, and then slide Cassette 3 and 4 out.2) Loosen the 2 fixing screws [1] at the left/right of the cassette.
F-2-543) Adjust the position of the cassette body [1] by shifting it to the front or the
rear.Shift to the rear = Decreases the left end marginShift to the front = Increases the left end margin
[2]
[3]
[4][1]
[1]
[1][2]
[3]
[4]
[4]
Due to the drop of toner from the drum separation claw, there may be a dirty image in the initial 10 sheets. This dirt disappears as copy volume goes on.
[1]
[1] [2]
[1]
Chapter 2
2-13
F-2-554) Check that the left margin of the copied image from Cassette 3/4 is as fol-
lows : L1=2.5-/+1.5mm
F-2-56[1] Feeding direction of paper
5) Tighten the 2 screws loosened at the step 2)6) Close Cassette 3/47) After the adjustment, perform the following in service mode:
Cassette 3COPIER> FUNCTION> CST> C3-STMTR/A4R Register the basic value for paper in Cassette 3:1) Set the STMTR/A4R size papers in Cassette 3, and align the side guideplate with the STRTR/A4R width.2) Select C3-STMRT/A4R to be highlighted, and then by pressing the[ON] key, the numerical value after auto adjustment are registered.Cassette 4COPIER> FUNCTION> CST> C4-STMTR/A4R Perform the same operation as Cassette 3
<Front Deck Left/Right>1) Press the set release button to pull out the front deck left/right toward the
front.2) Loosen the 2 screws [2] and the 2 fixing screws [3] of the deck front cover
[1].
F-2-573) Move the cassette guide assembly [1] toward either the front or the back
and perform adjustment.Move the guide plate toward the back = the left margin is reducedMove the guide plate toward the front = the left margin is increased
F-2-584) Check that the left margin of the copied image from the front deck left/
right is as follows : L1=2.5 -/+ 1.5mm
F-2-59[1] Feeding direction of paper
5) Tighten the 4 screws loosened at the step 2)6) Close the front deck left/right
<Manual Feeder Tray>1) Move the side guide plate [1] to the center, and loosen the 2 screws [2] for
the slide guide to adjust the position of the slide guide.
F-2-60Move the slide guide toward the back = the left margin is reducedMove the slide guide toward the front = the left margin is increased
2) Tighten the 2 screws loosened at the step 1)
<Duplexing Feeder Unit>1) Make the left margin of the 2nd sided image as L1=2.5 -/+ 2.0mm by se-
lecting the following in service mode:COPIER > ADJUST > FEED-ADJ > ADJ-REFE
[1]
[1]
image
L1
[1]
[2][3]
[2][1]
[1]
imageL1
[1]
[2]
[1]
Chapter 2
2-14
F-2-61[1] Feeding direction of paper
Make the numerical value smaller = the left margin is reducedMake the numerical value larger = the left margin is increased(1mm shift by changing every 10 in the setting value)
2.2.20 Adjustment of image leading edge margin0015-4677
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Select the following in the service mode: COPIER > ADJUST > FEED-ADJ > REGIST
2) Change the setting value to adjust.(1mm shift by changing every 10 in the setting value)Check that the leading edge margin of the image picked up from eachcassette/deck is as follows : L1=4.0 +1.5 /-1.0mm
F-2-62[1]Feeding direction of paper
2.2.21 Mounting of the Host Machine0015-4745
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Storing of the drum rotational tool and the grip>1) Detach the lower rear right cover [1].
- 2 screws [2]
F-2-632) Store the following parts:
- Drum rotational tool [1]: store it along with the collecting toner cap tothe hole of the pullout grip at the top of the collecting toner case [2].- Grip: insert to the grip storing area [3]
F-2-64
3) Attach the lower rear right cover removed in the step 1).
<Attaching of the grip cover>1) Attach the grip cover (small) [1] to the latch face cover [2].
F-2-652) Attach the 3 grip covers (large) [1] and the cover [2] that was attached in
the step 1).
image
L1[1]
image
L1
[1]
[1]
[2]
If pulling out the pullout grip fully, it makes the drum rotational tool and the cap fail to be inserted.It is easy to insert them if pulling the pullout grip at moderate position shown in the figure below.
[1]
[2][3]
[1][2]
Chapter 2
2-15
F-2-66<Attaching of the service book case>1) Peel off the two-sided tape located at the back of the service book case [1]
to attach to the bottom plate of the host machine.
<Attaching of the shutdown label>1) Put the appropriate language shutdown label [1] on the indicated position.
F-2-67<Attaching of the document size label>1) Broaden the document size guide plate [1] for A3/A3 position, and then
fit the [A] of the document side guide plate with the position of A4/A3 ofthe document size label to attach the label.
F-2-68<Attaching of the touch pen>1) Set the touch pen [1] on the control panel.
F-2-69<After installation of the host machine>1) Clean around the machine.
2) Move the host machine to the specified position and fix it in place withthe 2 adjusters.
Be sure that the front side of the service book case is exposed for 6mm from the front side of the bottom plate [2] of the host machine when attaching the service book case.In case of attaching the service book case without any margin exposed from the bottom plate, it will cause the service book case to run into the rail of the paper deck when mounting the paper deck later.Be sure to attach the paper deck first and then attach the service book case in case of mounting the paper deck and attaching the service book case at the same time.
[1]
[1]
[2]
[1]
6mm or more[1] [2]
Position forbidden to attach the service book case- Inside the machine (inner side of the front cover)- Position to block off the louver area- Position to block off the grip area
[1]
A4A3A
[2]
[1]
[1]
Chapter 2
2-16
3) Fill in necessary information on the service book and store it to the service book case.
2.3 Checking the Connection to the Network
2.3.1 Overview0015-4748
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The information in this section applies when connecting the host machine to a network.If the user's network is in TCP/IP environment, use the PING command to see that the network settings are correct.There is no need to check the settings using the PING command if the use's network is in an IPX/SPX or Apple Talk environment.
2.3.2 Checking the Connection to the Network0015-7620
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Perform the shutdown sequence so that the main power can be turned off.2) Connect the network cable to the host machine, and turn on the main power switch.3) Inform the on-site system administrator that the installation work of the host machine is complete, and also ask him/her to setup the host machine for networking.
MEMO;The adjusters may be too hard to turn by hand. In such case, use a screwdriver to turn.
The following steps apply only if the machine is connected to a network.
To set up the machine for networking, it is necessary to enable [ON] for the following item in Initial Additional Functions :
> [System Settings] > [Network Setting] > [Change Setting/Display Connection Confirm]
[1]
Chapter 2
2-17
4) Perform the shutdown sequence so that the main power can be turned off.5) Turn on the main power switch.
2.3.3 Using the Ping Command0015-4749
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Make the following selections: > [System Settings] > [Network Settings] > [TCP/IP Settings] > [Ping Command]2) Using the keypad on the control panel, type in the correct IP address set in [Network Connection], and press the Execute key.
If successful, the message 'Response from host' will appear so that you can check that the IP address is valid; otherwise, the message will read 'No response fromhost'
2.3.4 Making a Check Using the Remote Host Address0015-4750
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can execute the PING command using the appropriate remote host address to see if a connection to the network is available.Remote host address: the IP address of a PC terminal connected to the TCP/IP network to which the machine is also connected.1) Inform the system administrator that you are going to check the network connection using the PING command.2) Check with the system administrator to find out the remote host address.3) Add the appropriate remote host address to the PING command.
- If the message is 'Response from host', the connection to the network is normal.- If the message is 'No response from host', the machine is not correctly connected to the network. Start the troubleshooting work in the next section.
2.4 Troubleshooting the Network
2.4.1 Troubleshooting the Network 0015-4751
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following information applies only when the machine is connected to a network. If attempts to connect to the network fail, suspect the following:
- The machine's TCP/IP settings are wrong. - The user's network is faulty.
To find out which, go through the following:
2.4.2 Checking the Connection of the Network Cable 0015-7621
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Check to be sure that the network cable is correctly connected to the Ethernet port. - If the connection is correct, make the next check. - If the connection is wrong, correct it and run the check once again using the remote host address.
2.4.3 Making a Check Using a Loopback Address 0015-4752
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
A loopback address comes back before reaching the network PCB. By executing the PING command using the address, you can find out whether the machine'sTCP/IP settings are correct. 1) Add the appropriate loopback address (127.0.0.1) to the PING command.
- If the message is "No response from host," check the machine's TCP/IP settings, and execute the PING command once again. - If the message is "Response from host," make the next check.
2.4.4 Making a Check Using a Local Host Address 0015-4753
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The "local host address" is the IP address of the machine, and the address comes back after reaching the network PCB. By executing the PING command using theaddress, you can find out whether the network PCB is free of a fault. 1) Add the IP address of the machine to the PING command.
If the message is "No response from host", go through the following and execute the PING command once again.- The machine's IP address may be wrong: Check the machine's IP address settings, and check with the system administrator to see if the assigned IP address isa valid one. - The connection of the network PCB may be wrong: Check the connection of the network PCB once again. - The network PCB may be faulty. Try replacing it. If the message is "Response from host", suspect a problem in the user's network environment. Report to the system administrator for appropriate action.
2.5 Installing the Copy Tray
2.5.1 Confirming the contents0015-4767
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Copy Tray L1>
In case of reentering the IP address, turning off and then on the main power is required in order to be enabled.
Chapter 2
2-18
F-2-70
2.5.2 Power off of the host machine0015-4768
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
2.5.3 Installation procedure0015-4769
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1] Delivery Bar 1 pc.
[2] Delivery Tray 1 pc.
[3] Magnet plate 1 pc.
[4] Delivery roll 2 pc.
[5] E ring 1 pc.
How to turn off the main powerWhen turn off the main power, implement the following steps to protect the hard disk of this product.1) Push the control panel power switch for 3 sec or more.2) Operate the touch panel following the instruction on the screen of shutdown sequence in order to be ready to turn off the main power switch.3) Turn off the main power switch.4) Pull out the power cable (for the outlet).
[1]
[2]
[4] [5][3]
Chapter 2
2-19
1) Open the front cover.2) Turn the fixing/feeding assembly release lever [1] in the direction of the arrow to release the transfer/separation charging unit. Slide the fixing/feeding assembly
[2] out.
F-2-713) Remove the delivery roller guide [1].
- 2 screws [2]
F-2-724) Attach the delivery roll.
- Attach the delivery roll [1] to the position of the pin [3] found in the center of the delivery roller shaft [2].- Fit the protrusion [4] of one delivery roll to the mounting hole [5] of the other delivery roll.- Fit E-ring [6] to the groove on the delivery roller shaft to mount.
F-2-73
- When mounting the delivery Tray to the host machine, be sure to attach the rollers in the center of delivery roller.- When mounting the delivery tray to the host machine, shift tray or finisher should not be mounted.
[1] [2]
[2] [1]
[2]
[1]
[2]
[3][4]
[6]
[5]
Chapter 2
2-20
5) Mount the delivery roller guide.6) Slide the fixing/feeding assembly in the machine and close the front cover.7) Detach the left cover (upper) [1].
- 2 screws [2]
F-2-748) Attach the magnet plate [1] to the left cover (upper) and bend the claws [2] at the both ends in the direction of the arrow.
F-2-759) Attach the left cover (upper).10) Fit the protruding parts [1] at the delivery tray end to the mounting holes [2] on the host machine.
See the figure below to make sure the mounting direction of the delivery roller's protrusion [1].
[1]
[1]
[1][2] [1]
[1]
[2]
Chapter 2
2-21
F-2-7611) Attach the delivery tray bar [1].
F-2-77
2.6 Installing the Card Reader
2.6.1 Notice At Installation0015-4772
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
2.6.2 Confirming the contents0015-4773
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Card Reader-C1>
F-2-78
Installation of this equipment needs the card reader attachment kit C2.
[1] Card reader 1pc.
[1]
[1]
[2]
[1]
C
[1] [2] [3]
Chapter 2
2-22
<Card Reader Attachment-C2>
F-2-79
2.6.3 Power off of the host machine0015-4774
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
2.6.4 Installation procedure0015-4775
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the toner replacement cover.2) Detach the Right cover (upper)[1].
- Screw [2] 2pc.
[2] Screw (RS tightening; M4X10) 1pc.
[3] Toothed washer 1pc.
[1] Card reader attachment plate 1pc.
[2] Joint plate 1pc.
[3] Screw (small panhead screw; M4X6) 1pc.
[4] Screw (RS tightening; M4X10) 2pc.
How to turn off the main powerWhen turn off the main power, implement the following steps to protect the hard disk of this product.1) Push the control panel power switch for 3 sec or more.2) Operate the touch panel following the instruction on the screen of shutdown sequence in order to be ready to turn off the main power switch.3) Turn off the main power switch.4) Pull out the power cable (for the outlet).
[1] [2]
[3] [4]
Chapter 2
2-23
F-2-803) Attach the card reader attachment plate [1].
- Screw (RS tightening; M4X10) [2] 2pc.
F-2-814) Attach the card reader to the joint plate [1] with 1 each of the toothed washer of the card reader and the screw (RS tightening; M4X10) [2].
F-2-825) Put the harness [1] of the card reader through the hole [2] of the card reader attachment plate.
F-2-836) Attach the card reader [1].
- Screw (small panhead screw; M4X6) [2] 1pc.
[2][1]
[1][2]
[2] [1]
[1] [2]
Chapter 2
2-24
F-2-847) Get the cable [1] out from the side of the host machine.
F-2-858) Connect the card reader harness with the connector [1].
F-2-869) Put the cable [1] of the card reader through the 2 clamps [2].
If the cable is difficult to remove, drivers etc. will help make the operation easier.
[1] [2]
[1]
[1]
Chapter 2
2-25
F-2-8710) Cut the area [1] of the right cover (upper) with a wire cutter etc.
F-2-8811) Attach the right cover (upper) detached in the step 2).12) Close the toner replacement cover.13) Insert the power cable (for the plug).14) Turn on the main power switch, and then check the display demanding setting of the control card.15) Input the card number (1 to 2001) to be used in the service mode (COPIER > FUNCTION > INSTALL > CARD).
- Input the smallest card number for the user to use.- Up to 1,000 cards having been input are available.
16) Operate the touch panel following the instruction on the screen of shutdown sequence in order to turn off the main power switch.17) Turn on the main power switch.18) Insert the control card and check the status where copy is possible.
2.6.5 Installing for imageWARE Accounting Manager0015-7624
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Check to see that 'ID00000001 to ID00001000' has been created in > [System Settings] > [Dep ID Mangement] > [Registor Dept.ID/Password] > [PageTotals]. (In the case that '1' has been input as the first number by the service mode; COPIER > FUNCTION > INSTALL > CARD)
2) Press the reset key to escape the user mode screen.
3) Select > [System Settings] > [Network Settings] > [TCP/IP Settings] > [IP Address Settings], and then make the setting of [IP Address], [Gateway Address],[Subnet Mask] according to the user environment
4) Press the reset key to escape the user mode screen.5) Operate the touch panel following the instruction on the screen of shutdown sequence in order to turn off the main power switch.6) Turn on the main power switch.7)
> [System Settings] > [System Maneger Settings], and then input any number into [System Maneger ID] and [System Password].8) Press the reset key to escape the user mode screen.9) Turn off the power according to the shutdown sequence.
2.7 Installing the Original Holder
2.7.1 Checking Contents 0015-4777
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Document Tray-K1
> [System Settings] > [System Maneger Settings] is selected and [System Maneger ID] and [System Password] are registered, 'Registration of card to the device' is impossible to execute in the setting of iWAM.
[2][1]
[1]
Chapter 2
2-26
F-2-89
2.7.2 Installation Procedure 0015-4778
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Tighten the 2 stepped screws (M4X33) [1] to the upper cover (right).
F-2-902) Hook the document tray [1] to the stepped screws tightened in the step 1.
F-2-91
[1] Document Tray 1 pc.
[2]* Stepped Screw (M4X31) 2 pc.
[3] Stepped Screw (M4X33) 2 pc.
* Not used with this host machine.
[1]
[2] [3]
[1]
Chapter 2
2-27
2.7.3 Checking Contents 0015-8032
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Document Tray-M1
F-2-92
T-2-4
2.7.4 Installation Procedure 0015-8034
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Tighten the 2 stepped screws (M4X33) [1] to the upper cover (right).
F-2-932) Hook the document tray [1] to the stepped screws tightened in the step 1.
If it is hard to hook the document tray, loosen the 2 stepped screws and hook it once again.
[1] Document Tray 1pc.
[2] Stepped Screw (M4X33) 2 pc.
MEMO;For the 120V model, use it as standard.
[1] [2]
[1]
Chapter 2
2-28
F-2-94
2.8 Installing the Reader Heater
2.8.1 Checking the Contents0015-7877
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Heater Kit>
F-2-95T-2-5
2.8.2 Power off of the host machine0015-7815
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If it is hard to hook the document tray, loosen the 2 stepped screws and hook it once again.
[1] Mirror Heater FK2-0229 1pc
[2] Lens Heater FK2-0228 1pc
[3] Cable Clamp WT2-0507 2pc
[4] Heater Harness Retainer FC5-2945 1pc
[5] Screw (RS tightening; M4X8) XB3-6400 4pc
[1]
[1] [3] [5][2] [4]
Chapter 2
2-29
2.8.3 Installation Procedure0015-7814
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the DADF.2) Remove the glass retainer [1].
- Remove the 2 screws [2]3) Remove the copyboard glass [3]
F-2-96
How to turn off the main powerWhen turn off the main power, implement the following steps to protect the hard disk of this product.1) Push the control panel power switch for 3 sec or more.2) Operate the touch panel following the instruction on the screen of shutdown sequence in order to be ready to turn off the main power switch.3) Turn off the main power switch.4) Pull out the power cable (for the outlet).
When removing the copyboard glass, be sure not to get your fingers touched with the glass surface or the backside of the white plate.In case the glass is soiled, clean it with lint-free paper.
[1]
[3]
[2]
Chapter 2
2-30
F-2-974) Hold the tab (the bend) [A] of the mirror stay to move the No. 1 mirror base [1] to the right until it stops.
F-2-985) Insert the front side of the mirror heater [1] under the cable guide [2] and connect the connecter [3], and then tighten with the 2 screws (RS tightening; M4X8) [4].
F-2-996) Attach the heater harness retainer [1].
- 1 screw (RS tightening; M4X8) [2]
[1][A]
[1]
[3]
[4]
[4]
[1][2]
Chapter 2
2-31
F-2-1007) Hold the tab (the bend) [A] of the mirror stay to move the No. 1 mirror base [1] to the left until it stops.
F-2-1018) Insert the cable clamp [1] to the hole [2] of the frame.
F-2-1029) Attach the lens heater [1]
- 1 connector [2]- 1 cable clamp [3]- 1 screw (RS tightening; M4X8) [4]
F-2-103
Tighten the screw [3] while pushing on the lens heater [1] in the direction of the emboss [2]. Be sure that the heater's claw [4] must not be disengaged when performing this operation. Also check that the bottom of the heater must not be off from the board.
[1] [2]
[1]
[A]
[1]
[2]
[2]
[3]
[4]
[1]
Chapter 2
2-32
F-2-10410) In case that the cable [1] is loose, insert the cable clamp [2] to the frame's hole to fix the cable in place.
F-2-10511) By reversing the steps used to remove, attach the copyboard glass and the glass retainer.12) Close the DADF.13) Shift the cassette heater switch [1] and the environment switch [2] to the on position.
F-2-106
2.9 Installing the Cassette Heater
2.9.1 Checking Components0015-7889
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Cassette Heater>
F-2-107
[1]
[2]
[3]
[4]
[1] [2]
ON
[2][1] [3]
Chapter 2
2-33
2.9.2 Power off of the host machine0015-7816
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
2.9.3 Installation Procedure of the Cassette Heater0015-4781
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the wire saddle [1] to disengage the reader communication cable [2].
F-2-1082) Detach the upper rear cover [1].
- 6 screws [2]
[1] heater unit FM2-4182-000 1pc.
[2] cassette stay FB2-7052-000 1pc.
[3] screw (M4X6) XB1-2400-609 6pc.
How to turn off the main powerWhen turn off the main power, implement the following steps to protect the hard disk of this product.1) Push the control panel power switch for 3 sec or more.2) Operate the touch panel following the instruction on the screen of shutdown sequence in order to be ready to turn off the main power switch.3) Turn off the main power switch.4) Pull out the power cable (for the outlet).
Be sure to disconnect the power outlet.
[2][1]
Chapter 2
2-34
F-2-1093) Detach the lower rear cover [1].
- 6 screws [2]
F-2-1104) Remove the heat exhaust fan (filter) [1].
- 3 screws [2]- 1 connector [3]
F-2-1115) Hold down the release button [1] to slide Cassette 4 [2] out.
[1]
[1]
[2]
[2]
[2]
[1]
[2][2]
[2]
[2] [1]
[2][3]
Chapter 2
2-35
F-2-1126) Lift the inner unit [1] in Cassette 4, and remove it.
F-2-1137) In the same way, remove the inner unit of Cassette 3.8) Engage the claw [A] of the lead edge onto the long hole [B] of the host machine to attach the cassette stay [1].
F-2-114
Make sure from the rear side of the host machine that the claw [A] of the cassette stay is engaged appropriately.
[1]
[2]
[1]
[1]
[A]
[B]
Chapter 2
2-36
9) Secure the cassette stay [1] in place from the rear side of the host machine.- 2 screws (M4X6) [2].
F-2-11510) Secure the cassette stay [1] in place from the front side of the host machine.
- 2 screws [2] (M4X6)
F-2-11611) Put the cassette heater connector [1] through the long hole [A], while at the same time hook the metal plate [B] on the rear side of the cassette heater [2] onto
the hole [C] of the cassette heater.
Make sure that the heater cord guide [3] is fitted in place appropriately on to the long hole [A].
[A][A]
[2]
[1]
[2]
[1]
Chapter 2
2-37
12) Lift the cassette heater [1] until it touches the host machine, and then secure it in place at the specified position with the 2 screws (M4X6) [2].
F-2-11713) Connect the connector [1] on the host machine and the cassette heater connector [2].
F-2-118
[A]
[B][B][C]
[3] [3]
[2]
[1]
[1] [2]
[1]
[2]
Chapter 2
2-38
14) Attach the covers etc., by the reverse procedure to detach them.- heat exhaust fan (filter)- lower rear cover- upper rear cover- Secure the reader communication cable in the wire saddle.
15) Fit the inner units in each cassette in place, and then attach the cassettes onto the host machine.16) Connect the power supply cable (for power outlet) of the host machine.17) Turn on the main power switch.
2.10 Installing the Deck Heater
2.10.1 Checking the Parts to Install0016-0491
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Every components of the cassette heater unit are supplied as service parts, so have the following parts on hand.
F-2-119T-2-6
No. Part name Part number QTY No. Part name Part number QTY
[1] Heater unit FG6-9651 1pc. [7] Power supply label FS6-8725 1pc.
[2] AC input connector FG6-1117 1pc. [8] Binding screw (M4 X 4) XB1-2400-409 4pcs.
[3] Relay harness unit FG6-2957 1pc. [9] Wire saddle (Not used for this product) WT2-5730 3pcs.
[4] AC cable FK2-4379 1pc. [10] Power supply code base FC7-5473 1pc.
[5] Screw (w/ washer) XB2-7400-607 3pcs. [11] Screw (w/ flat spring) XB2-8401-007 1pc.
[6] Cable protection bush WT2-5098 1pc. [12] Wire saddle WT2-5738 1pc.
[8]
[2]
[5]
[5]
[10][8]
[7]
[12][9]
[3] [6]
[4]
[1][5]
[11]
Chapter 2
2-39
2.10.2 Turning Off the Host Machine0016-1684
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Turning Off the Main Power of the Host Machine When turning off the main power, be sure to go through the following in strict sequence to protect the machine'shard disk:[1] Hold on the power switch on the control panel 3 sec or more.[2] Operate on the touch panel according to the shut-down sequence indicated so that the main power switch may be turned off.[3] Turn off the main power switch.[4] Disconnect the power cable (for the power outlet).
2.11 Installing the Deck Heater (Large Deck)
2.11.1 Checking the Parts to Install0016-1496
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Every components of the cassette heater unit are supplied as service parts, so have the following parts on hand.
F-2-120T-2-7
No. Part name Part number QTY No. Part name Part number QTY
[1] Heater unit FG6-9651 1pc. [7] Power supply label FS6-8725 1pc.
[2] AC input connector FG6-1117 1pc. [8] Binding screw (M4 X 4) XB1-2400-409 4pcs.
[3] Relay harness unit FG6-2957 1pc. [9] Wire saddle WT2-5730 3pcs.
[4] AC cable FK2-4379 1pc. [10] Power supply code base FC7-5473 1pc.
[5] Screw (w/ washer) XB2-7400-607 3pcs. [11] Screw (w/ flat spring) XB2-8401-007 1pc.
[6] Cable protection bush WT2-5098 1pc. [12] Wire saddle WT2-5738 1pc.
[3]
[8]
[1]
[5][6]
A
A
[2]
[5]
[5]
[10]
[8]
[12][9]
[4]
[11]
[7]
Chapter 2
2-40
2.11.2 Turning Off the Host Machine0016-1691
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Turning Off the Main Power of the Host Machine When turning off the main power, be sure to go through the following in strict sequence to protect the machine'shard disk:[1] Hold on the power switch on the control panel 3 sec or more.[2] Operate on the touch panel according to the shut-down sequence indicated so that the main power switch may be turned off.[3] Turn off the main power switch.[4] Disconnect the power cable (for the power outlet).
2.12 Installing the Voice Guidance Kit
2.12.1 A point to keep in mind at installation0015-7208
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
2.12.2 Checking the Contents0015-4782
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Voice Guidance Kit-B1>
F-2-121
When installing the machine, see the Combination Table for Accessory Installation.
Before starting to install the Voice Guidance Kit, check to be sure that the Expansion Bus-D2 has properly been installed.
[1] Speaker Unit (Upper) 1pc. [2] Speaker Unit (Lower) 1pc.
[3] Cable (1300 mm) 1pc. [4]* Cable (1850 mm) 1pc.
[5] Cable Guide 7pc. [6] Voice Board 1pc.
(this machine requires 6 cord guides)
[7] Voice Board instruction plate 1pc. [8]* Voice Board instruction plate 1pc.
[1] [2] [3] [4] [5] [6]
[9][8][7] [10] [14] [15][11] [12] [13]
[16] [17]
Chapter 2
2-41
2.12.3 Power off of the host machine0015-4783
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
2.12.4 Installation Procedure0015-4784
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the cable clamp [1], and disconnect the reader communications cable [2].
F-2-1222) Detach the upper rear cover [1].
- 6 screws [2]
F-2-123
[9] Screw (binding; M3X6) 2pc. [10] Screw (binding; M4X6) 1pc.
[11] Screw (binding; M4X40) 2pc. [12]* Screw (binding; M3X16) 1pc.
[13]* Screw (binding; M4X16) 1pc. [14] Ferrite Core 1pc.
[15]* Wire Saddle 1pc. [16] Voice Guidance Kit Users Guide 1pc.
[17] Voice Guidance Kit Users Guide CD 1pc.
* Not used for this machine
How to turn off the main powerWhen turn off the main power, implement the following steps to protect the hard disk of this product.1) Push the control panel power switch for 3 sec or more.2) Operate the touch panel following the instruction on the screen of shutdown sequence in order to be ready to turn off the main power switch.3) Turn off the main power switch.4) Pull out the power cable (for the outlet).
[2][1]
[2]
[2]
[1]
Chapter 2
2-42
3) Detach the main controller box cover [1].- 4 screws [2]
F-2-1244) Remove the face cover plate [1]. (The removed plate is not used after this step.)
- 2 screws [2]
F-2-1255) Attach the Voice Board instruction plate [2] to the voice board [1].
- 2 screws (binding; M3X6) [3]
F-2-126
Checking the Position of the Slide Switch (SW1) on the Voice Guidance BoardThe slide switch (SW1) on the Voice Guidance Board is provided as a means of switching frequencies (33 MHz/66 MHz) to suit the transfer speed of the PCI bus. It is important for the switch setting to suit the transfer speed so that the voice will be free of interruption. If you inadvertently moved the slide, be sure to put it back to its correct position. For the Boad, the frequency must be set to 66 MHz.
[2]
[1]
[2] [1]
[1]
[2][3]
Chapter 2
2-43
6) Mount the voice board [1] to the PCI Expansion Kit-D2 using the 2 screws [2] removed in step 4).
7) Attach the removed parts.- Main controller box cover - Upper rear cover
8) Connect the reader communication cable.9) Close the reader communication cable with the wire saddle.10) Mount the speaker Unit (Lower) [1] to the upper right cover of the host machine.
- 2 screws (binding; M4X40) [2]
Cautions in mounting- A voice board [1] must be mounted to a specified position.Be sure to mount it to the slot [A] on the Expansion Bus B-1 board.Do not mount it to the slot [B] or [C].- If other board is mounted to the slot [A] , pull the board out of the slot and mount it to other slot. Then, mount a voice board to the slot [A] .- Be sure that the PCB is perpendicular to the connector.
33MHz
66MHz
[2][1]
[A] [B][C]
[A] [B][C]
Chapter 2
2-44
F-2-12711) Mount the speaker unit (upper) [1] on the speaker unit (lower), fix them with a screw (binding; M4X6) [2] from beneath.
F-2-12812) Take off the cover [1] from the code guide.
F-2-12913) Peel off the released paper of the code guide [1] and affix it to the host machine as shown in the figure.
The right side --- 2 places
F-2-130
The rear -- 4 places
[1]
[2]
[1]
[2]
[1]
[1]
Chapter 2
2-45
F-2-13114) Connect the cable [2] into the speaker unit [1].
F-2-13215) Run the cable [1] through the cable guide [2] and mount the cable guide cover [3].
F-2-13316) Attach the ferrite core [1] to the cable. Be sure that the length [2] is 50 mm or shorter.
F-2-13417) Connect the cable [1] to the terminal [2] of the voice board.
There should no excessive bending of the cable.
[1]
[1]
[1]
[2]
[1]
[1][2]
[3]
[1]
[2]
Chapter 2
2-46
F-2-13518) Run the cable [1] through the code guide [2] and mount the code guide cover [3].
F-2-13619) Connect the power cable to the outlet.20) Turn ON the main power switch.21) Check if the voice board is recognized.
Service modeSelect COPIER > DISPLAY > ACC-STS > PCIIf "Voice Board" is displayed, that means that the voice board is correctly recognized.
2. Setting After InstallationTo use 'voice guidance' after power-on, it is necessary to set the followings.
1) Select > [System Settings] > [Voice Guide Manegement Settings] > [Use Voice Guide].2) Select ON key (Default: OFF)3) Press OK key.
3. Operation Check<When Using the Voice Guidance>
1) Press the reset key for 3 sec or longer.2) When the display of the number of copy is enclosed with red lines on the screen, "Voice Guidance" becomes enabled.
<When Stopping the Usage>1) Press the reset key for 3 sec or longer.
There should no excessive bending of the cable.
[1]
[2]
[3]
[2]
[2]
[2]
[1]
[3]
[3]
Chapter 2
2-47
Chapter 3 Basic Operation
Contents
Contents
3.1 Construction ...................................................................................................................................................................3-13.1.1 Functional Construction............................................................................................................................................................... 3-13.1.2 Wiring Diagram of the Major PCBs ............................................................................................................................................ 3-13.1.3 Controlling the Main Motor (M2)................................................................................................................................................ 3-2
3.2 Basic Sequence ..............................................................................................................................................................3-33.2.1 Basic Sequence of Operation (at power-on; 30-sec start-up mode)............................................................................................. 3-33.2.2 Basic Sequence of Operation (at power-on; low-temperature start-up mode)............................................................................. 3-33.2.3 Basic Sequence of Operation (at power-on; high-humidity start-up mode) ................................................................................ 3-43.2.4 Basic Sequence of Operation (at time of copying/printing) ........................................................................................................ 3-5
Chapter 3
3-1
3.1 Construction
3.1.1 Functional Construction0015-4341
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine may be divided into the following seven functional blocks:
F-3-1
3.1.2 Wiring Diagram of the Major PCBs0015-4343
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Charging
Cleaning
FeedingDerivery tray
Development
Image Formation System
Manualfeedtray
Paper Deck(option)
Pickup/Feeding System
Photo-sensitivedrum
PickupcontrolS
epar
atio
n
Fix
ing
Tra
nsfe
r
Lower feeding assembry
Deck left Deck right
Cassette 3
Cassette 4
HDDControl panel
DC controller PCBMain controller PCB
Reader controller PCB
Laser driver PCB
Laser scanner
Original Exposure System
Laser Exposure System
Printer Control System
DC power supply PCB
Optionboards
General Control System
Reader Control System
Optical path Original illumination
Original
CCD/AP PCB
Video PCB
Chapter 3
3-2
F-3-2
3.1.3 Controlling the Main Motor (M2)0015-4344
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The functions of the main motor control circuit are as shown in the following table, and its block diagram is shown in the following figure:T-3-1
1) When the main motor drive signal (MAIN_M_ON) goes '1', the main motor starts to rotate.2) When the main motor rotates, clock pulse signals (MAIN_M_FG) are generated. If the DC controller PCB detects an error in clock pulse signals, it will indicate
"E010" in the control panel.
Item Description
Power supply 24V is supplied by the DC controller PCB
drive signal from the DC controller PCB (MAIN_M_ON)
Operating/driving Collecting toner feedscrewCleaning assemblyRegistration rollerManual feed pickup assemblyLeft deck feed roller 2Developing assembly unit
Control Turning on/off the motorControlling the motor to a specific speed
Error detection code E010
Readerrelay PCB
Main controller PCBDC
controllerPCB
Hard disk
ADF
BD PCB
CCD/AP PCB
Motor driver PCB
Potential control PCB
Environment sensor PCB
Cassette 3 paper level
detection PCB
Cassette 4 paper level
detection PCB
Duplexing driver PCB
Inverter PCB
HVT PCB
Reader controller PCB
J3031
Control card IV
(accessory)
J1024
Laser scanner motor
J601
J206
Laser driver PCB
J102
J113
DC power supply PCB
J101
J113
J113
AC driver PCB
J102
J107
J1015J122
J1064
J6801
J1018
J205
J104
J105
J102
J2101
J2113
J1355
J1014
J2M
J201
J204
J101
Scanner motor
M501
M22
J810
J2055
J806
J8492
J4502
J4003
J2302
J426
IH driver PCB
J1031J1041
J130J131
Memory PCB
J503
J203
J501
J502
Keypad PCB
Inverter PCB
J6801J6802
J1110 J1111J1112J1114J1113
J3
J2J1
LCD panel(LCD)
Control panel CPU PCB
Reader Interface PCB
J301
J306
J305J312
J505M
J315T
J505T
J2
J202
J308J309
Video PCB
J1406
J1406
J1406J1408J1411
J5501J4500J5503
J2701
J2511
J122
J6502
J126
J2302
J2511
J426
Note: The symbol in the diagram indicates major wiring connections, and does not indicate the flow of signals.
Chapter 3
3-3
F-3-3
3.2 Basic Sequence
3.2.1 Basic Sequence of Operation (at power-on; 30-sec start-up mode)0015-4347
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-3-4*1: After a shift to standby, the fixing target temperature is decreased in 5-deg C increments at specific time intervals. When a specific temperature is reached, the
fixing heater and the fixing motor are turned on and off to maintain the temperature.T-3-2
3.2.2 Basic Sequence of Operation (at power-on; low-temperature start-up mode)0015-4348
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Interval DescriptionWMUPR (warm-up) For 30 sec after the main power is turned on.CNTR (control rotation) The machine executes potential control for the photosensitive drum. In the case of 30-sec start-up mode, the machine measure
the potential for a single rotation of the drum, and adjusts only the target output. (VL control)
PSTBY (print standby) The machine is in a state in which it is ready to accept a copy/print request signal.
Drive circuit
Control circuit Referencesignal generation circuit
Clock pulse generation circuit
J631J4005
DC controller PCB
DC power supply PCB
1
2
1
2
24V
GND Main motor (M2)
J632J1081
23
4
A8
A7A6
A5
MAIN_M_GND
MAIN_M_CLK
MAIN_M_5V
MAIN_M_ON
A4 5MAIN_M_FG
Main powerswitch ON
CNTRWMUPR PSTBY
Main motor(M2)Drum motor(M1)
Primary charging
Pre-exposureLED (LED1)
Developing clutch(CL1)Developing bias(DC)Developing bias(AC)
Pre-transfercharging (DC)Pre-transfercharging (AC)
Separationcharging (DC)Separationcharging (AC)Fixing motor(M3)Fixing heater(IH)
Laser
Transfer charging
Bias roller
30 sec (approx.)
205 deg C
*1
Chapter 3
3-4
F-3-5*1: After a shift to standby, the fixing target temperature is decreased in 5-deg C increments at specific time intervals. When a specific temperature is reached, the
fixing heater and the fixing motor are turned on and off to maintain the temperature.T-3-3
3.2.3 Basic Sequence of Operation (at power-on; high-humidity start-up mode)0015-4349
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Interval DescriptionWMUPR (warm-up) From when the main power is turned on until the fixing roller temperature reaches a
specific level and, in addition, the potential control of the photosensitive drum ends, and as much as 60 sec passes from power-on.
CNTR (control rotation) The machine executes potential control of the photosensitive drum. For each mode (i.e., copier, printer), the machine executes VD control (to adjust the primary discharge current) and Vl control (to adjust the laser output), and determines Vdc (developing bias).
PSTBY (print standby) The machine is in a state in which it is ready to accept a copy/print request signal.
CNTRWMUPR PSTBY
*1
Main powerswitch ON
Main motor(M2)Drum motor(M1)
Primary charging
Pre-exposureLED (LED1)
Developing clutch(CL1)Developing bias(DC)Developing bias(AC)
Pre-transfercharging (DC)Pre-transfercharging (AC)
Separationcharging (DC)Separationcharging (AC)Fixing motor(M3)Fixing heater(IH)
Laser
Transfer charging
Bias roller
60 sec (approx.)
215 deg C
Chapter 3
3-5
F-3-6*1: After a shift to standby, the fixing target temperature is decreased in 5-deg C increments at specific time intervals. When a specific temperature is reached, the
fixing heater and the fixing motor are turned on and off to maintain the temperature.T-3-4
3.2.4 Basic Sequence of Operation (at time of copying/printing)0015-4350
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-3-7
Interval DescriptionWMUPR (warm-up) From when the main power is turned on until the fixing roller temperature reaches a specific level, the potential control of
the photosensitive drum ends, and as much as 60 sec passes from power-on.
CNTR (control rotation) The machine executes potential control of the photosensitive drum. For each mode (i.e., copier, printer), it executes VD control (to adjust the primary discharge current) and VL control (to adjust the laser output) and determines Vdc (developing bias).
PSTBY (print standby) The machine is in a state in which it is ready to accept a copy/print request signal.
CNTRWMUPR PSTBY
*1
Main powerswitch ON
Main motor(M2)Drum motor(M1)
Primary charging
Pre-exposureLED (LED1)
Developing clutch(CL1)Developing bias(DC)Developing bias(AC)
Pre-transfercharging (DC)Pre-transfercharging (AC)
Separationcharging (DC)Separationcharging (AC)Fixing motor(M3)Fixing heater(IH)
Laser
Transfer charging
Bias roller
60 sec (approx.)
205 deg C
PSTBY PINTR PRINT LSTR PSTBY
*2
1st PRINT
*1 *1
2nd PRINT
Main powerswitch ON
Main motor(M2)Drum motor(M1)
Primary charging
Pre-exposureLED (LED1)
Developing clutch(CL1)Developing bias(DC)Developing bias(AC)
Pre-transfercharging (DC)Pre-transfercharging (AC)
Separationcharging (DC)Separationcharging (AC)Fixing motor(M3)Fixing heater(IH)
Laser
Transfer charging
Bias roller
Chapter 3
3-6
*1: temperature control under way for fixing standby mode.*2: as in the case of standby, while copying/printing is under way, the fixing target temperature is decreased to suit the passage of time after the end of start-up.
T-3-5
Interval DescriptionPSTBY (standby) The machine is in a state in which it can accept a copy/print request signal.
PNTR (initial rotation) From when a print request signal is received until the image signal is generated.
PRINT (print) The machine is in a state in which a toner image is transferred to paper and the paper is discharged.
LSTR (last rotation) The machine is in a state in which paper has been discharged and all drive has ended.
Chapter 4 Main Controller
Contents
Contents
4.1 Construction ...................................................................................................................................................................4-14.1.1 Construction and Mechanisms ..................................................................................................................................................... 4-1
4.2 Construction of the Electrical Circuitry .........................................................................................................................4-14.2.1 Main Controller PCB ................................................................................................................................................................... 4-14.2.2 HDD............................................................................................................................................................................................. 4-2
4.3 Start-Up Sequence..........................................................................................................................................................4-44.3.1 Overview...................................................................................................................................................................................... 4-44.3.2 Start-Up Sequence ....................................................................................................................................................................... 4-4
4.4 Shut-Down Sequence.....................................................................................................................................................4-64.4.1 Overview...................................................................................................................................................................................... 4-64.4.2 Flow of Operation ........................................................................................................................................................................ 4-6
4.5 Image Processing ...........................................................................................................................................................4-64.5.1 Overview of the Image Flow ....................................................................................................................................................... 4-64.5.2 Construction of the Image Processing Module ............................................................................................................................ 4-74.5.3 Reader Unit Input Image Processing ........................................................................................................................................... 4-74.5.4 Compression/ Extension/ Editing Block...................................................................................................................................... 4-84.5.5 Printer unit Output Image Processing .......................................................................................................................................... 4-8
4.6 Flow of Image Data........................................................................................................................................................4-94.6.1 Flow of Image Data According to Copy Functions ..................................................................................................................... 4-94.6.2 Flow of Image Data for the Box Function ................................................................................................................................... 4-94.6.3 Flow of Image Data for the SEND Function ............................................................................................................................. 4-104.6.4 Flow of Image Data for the Fax Transmission .......................................................................................................................... 4-104.6.5 Flow of Image Data for the Fax Reception Function ................................................................................................................ 4-114.6.6 Flow of Image Data for the PDL Function ................................................................................................................................ 4-12
4.7 Parts Replacement Procedure.......................................................................................................................................4-134.7.1 Main Controller Box .................................................................................................................................................................. 4-13
4.7.1.1 Before Removing the Main Controller Box..................................................................................................................................................4-134.7.1.2 Removing the Main Controller Box..............................................................................................................................................................4-13
4.7.2 Main Controller PCB ................................................................................................................................................................. 4-134.7.2.1 Before Removing the Main Controller PCB.................................................................................................................................................4-134.7.2.2 Removing the Main Controller PCB.............................................................................................................................................................4-134.7.2.3 When Replacing the Main Controller PCB...................................................................................................................................................4-14
4.7.3 SDRAM ..................................................................................................................................................................................... 4-144.7.3.1 Before Removing the SDRAM .....................................................................................................................................................................4-144.7.3.2 Removing the SDRAM .................................................................................................................................................................................4-14
4.7.4 Boot ROM.................................................................................................................................................................................. 4-144.7.4.1 Before Removing the Boot ROM .................................................................................................................................................................4-144.7.4.2 Removing the Boot ROM .............................................................................................................................................................................4-14
4.7.5 HDD........................................................................................................................................................................................... 4-154.7.5.1 Before Removing HDD.................................................................................................................................................................................4-154.7.5.2 Removing the HDD.......................................................................................................................................................................................4-154.7.5.3 After Replacing the HDD..............................................................................................................................................................................4-15
4.7.6 Video PCB ................................................................................................................................................................................. 4-154.7.6.1 Before Removing the Video PCB .................................................................................................................................................................4-154.7.6.2 Removing the Video PCB.............................................................................................................................................................................4-15
4.7.7 Controller Fan ............................................................................................................................................................................ 4-164.7.7.1 Before Removing the Controller Cooling Fan ..............................................................................................................................................4-164.7.7.2 Removing the Controller Cooling Fan..........................................................................................................................................................4-16
Chapter 4
4-1
4.1 Construction
4.1.1 Construction and Mechanisms0015-4355
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's main controller block consists of the following and has the following functions:
T-4-1
F-4-1
4.2 Construction of the Electrical Circuitry
4.2.1 Main Controller PCB0015-4356
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following is a diagram showing the major control mechanisms of the main controller according to connectors:
Item Description
Main controller PCB Controls system operation, memory, printer unit output, image processing, scanner unit image input processing, rendering, color LCDcontroller, card reader unit interface, fax imageprocessing, etc.
SRAM Retains service mode settings (by SRAM), HDD management information
Image memory (DDR SDRAM) Temporarily retains image data (1024 MB)
BOOTROM Stores boot program
HDD Stores system software, retains image data forBox/Fax function (40 GB)
USB port x 2 USB2.0 interface
Ethernet port (10/100Bsae-T) Ethernet interface
Video PCB Pixel/line conversion, laser scaner motor control
Main controller PCB
USB port (H)
PCI expansion board
DC controller PCB
Reader Unit
HDD
Boot ROM
SRAM
Image memory (SDRAM)
Ethernet10/100BASE-T
USB port (D)
Video PCB
Chapter 4
4-2
F-4-2T-4-2
4.2.2 HDD0015-4357
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The HDD is divided into 11 partitions (blocks), each assigned with specific functions.T-4-3
Connector Description Connector Description
J1003J1004
DDR SDRAM connection slot J1024 New card reader connector
J1010 Boot ROM connector slot J1060 CC-V connector
J1013 PCI enhance board connection slot J1061 LAN connector
J1014 Reader interface connector J1062 New coin robo connector
J1015 Printer interface connector J1064 Hard disk connector
J1016 USB host interface connector J3000 Power supply connector (5V non all night)
J1017 USB device interface connector J3001 Power supply connector (3.3V non all night)
J1018 Control panel connector J3002 Power supply connector (3.3V all night)
J1021 Power supply control connector
Partition Description
FSTDEV Collects compressed image data.
TMP_GEN Stores temporary files, log data.
J1014 J1018
J1060J1024 J1022
J1023
J1062
J1040
J1015
BAT1001
J1030
J1059
J1063 J1021
J3000
J3002
J3001
J1006
J1003
J1004
J1032
J1010
J1016
J1017
J1013
J1034
J1061
J1064J1002
Chapter 4
4-3
F-4-3
The following shows the construction of the machine's system software:
T-4-4
TMP_PSS PDL spool
TMP_FAX Ensures fax reception.
APL_SEND Stores user data (address book, transfer settings).
APL_MEAP Stores MEAP applications.
APL_GEN Mode memory data, standard mode dataHistory (e.g., print job history)iFax image dataFax image dataOther
IMG_MNG Stores file management table, profile.
PDL_DEV Stores PDL font, etc.
BOOTDEV Stores execution module, message data file, RUI content, etc.
FSTCDEV Chasing (not used)
System Software Description Location Remarks
System System module (controls mechanism as a whole)
HDD (BOOTDEV)
Language Language module (controls LCD indications)
HDD (BOOTDEV)
RUI Remote user interface module HDD (BOOTDEV)
Boot Starts up the machine Boot ROM DIMM
G3FAX Controls G3 Fax (2-port) G3 Fax board DIMM
Controls G3 Fax (1-port) HDD (BOOTDEV)
Dcon Controls the DC controller DC controller PCB Flash ROM (soldered)
Rcon Controls the Reader controller Reader controller PCB Flash ROM (soldered)
Meapcont Controls MEAP applications HDD (BOOTDEV)
SDICT OCR dictionary HDD (BOOTDEV)
KEY encryption communication key HDD (BOOTDEV)
Partition Description
HDD
TMP_GEN
TMP_PSS
FSTDEV
APL_SEND
APL_MEAP
IMG_MNG
APL_GEN
BOOTDEV
FSTCDEV
PDLDEV
TMP_FAX
Chapter 4
4-4
F-4-4*1: 1-port FAX*2: 2-port FAX
4.3 Start-Up Sequence
4.3.1 Overview0015-4358
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The system software used to control the machine is stored on the HDD.When the machine is started, the CPU on the main controller PCB reads the system software from the HDD according to the instructions of the boot ROM bootprogram, and writes it to the image memory (SDRAM) of the controller PCB.While the CPU reads the system software from the HDD to the image memory (DRAM), the control panel shows the following screen, using a progress bar toindicate the progress of the start-up sequence.
F-4-5
Do not turn off the main power while the progress bar is indicated, as access is being made to the HDD. Turning off the power can cause a fault on the HDD (iden-tified by E602).
4.3.2 Start-Up Sequence0015-4359
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Boot ROM Area>
Reader Unit
BOOT
DCON
RCON
G3FAX *2
SYSTEMLanguage
RUIMEAP
G3FAX *1SDICTKEY
Main Controller PCB
DC Controller PCB
HDD
G3 FAX Unit
Progress bar
Chapter 4
4-5
- Self Diagnosis Program (interval 1)The self-diagnosis program is run by the CPU on the main controller PCB when the main power switch is turned on.The program is used to check the condition of the image memory (SDRAM) and the HDD. The machine will indicate an error code if it finds a fault while running the program.- Boot Program (interval 2)When the self-diagnosis program ends normally, the CPU on the main controller PCB executes the boot program.The program is used to read the system software from the HDD to write it into the image memory (SDRAM).- Image Memory (SDRAM) Area (interval 3)The system software written by the boot program initializes the various functional blocks (e.g., I/F settings of the main controller).When all the foregoing ends normally, the machine becomes ready to accept a job (i.e., the control panel shows the Operation screen, and the LED on the Start keychanges from red to green).
F-4-6
F-4-7
1
Progress bar
32
Image memory (SDRAM)
CPU
HDD
System area
Image data area
BootROM
Self diagnosis program
Boot program
: access to the program during execution: access for checking
Main controller PCB
- While the Self-Diagnosis Program Is Being Executed
Chapter 4
4-6
F-4-8
4.4 Shut-Down Sequence
4.4.1 Overview0015-4360
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If the main power switch is turned off while the machine is accessing its HDD, damage can well occur on the HDD. To avoid such damage, the machine is providedwith a shut-down sequence.
4.4.2 Flow of Operation0015-4361
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following diagram shows the flow of shut-down operation:
F-4-9
4.5 Image Processing
4.5.1 Overview of the Image Flow0015-4362
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the flow of images in relation to the machine's functions:
Image memory (SDRAM)
CPU
HDD
System area Image data area
BootROM
Main controller PCB
Self-diagnosis program
Boot program
: access to the program during execution.
: flow of the system program.
- While the Boot Program Is Being Run
System software
Press on the control panelpower switch (3 sec or more)
HDD protection check mode
HDDprotection execution mode
Main power switch off
Indicates the job being executed, and informs the user that it will start the shut-down sequence.
Moves to the shut-down sequence.
Cancels any job on wait in print mode.Cancels any job on wait in print mode.Cancels any job being executed in fax mode.
Chapter 4
4-7
F-4-10
4.5.2 Construction of the Image Processing Module0015-4363
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's major image processing is executed by the main controller PCB.The following shows the construction of the modules associated with image processing:
F-4-11
4.5.3 Reader Unit Input Image Processing0015-4364
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The image data colleted by the contact image sensor is processed by the main controller PCB.
SENDFAXPullScanE-MailPDL PrintBOX
PC
Original
Copy
A
AAPrint
Scan
Image data
Other iR machine
SDRAMHDD
Reader controllerPCB
- image memory- program (temporary storage)
Processes the image data read by the reader unit.
Reader unit input processing block
Processes image data foroutput to the printer unit.
Printer unit output image processing block
Main controller PCBDC controller PCB
Reader unit
Chapter 4
4-8
F-4-12
4.5.4 Compression/ Extension/ Editing Block0015-4365
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Here, image data is processed for compression, extension, and editing.
F-4-13
4.5.5 Printer unit Output Image Processing0015-4366
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The main controller processes the image data coming from the printer unit for output to the printer unit.
Film photo mode
Binary processing (screen processing)Binary processing (error diffusion)
To compression/expansion/editing block
Edge emphasis
Enlargement/reduction
Text modeText/photo/film photo mode
-intensify-to-density conversion-density adjustment (F adjustment)-gamma correction
Main controller PCB
Reader unit
Main controller PCB
to printer unit output image processing block
Enlargement/reduction
Rotation
Integration
Compression
Expansion
Printer unit imageprocessing block
PDPDL image processing block
SDRAM
HDD
Chapter 4
4-9
F-4-14
4.6 Flow of Image Data
4.6.1 Flow of Image Data According to Copy Functions0015-4367
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following is the flow of image data when the Copy Function is in use:
F-4-15
4.6.2 Flow of Image Data for the Box Function0015-4368
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following is the flow of image data when the Box function is in use:
Main controller PCB
To DC controller PCB
For PDL data, when fine line processing is ON
Compression/expansion/editing block
Binary density conversion
Enlargement/reduction
Smoothing
Thickening
Image processing block for printer unit
Image processing block for printer unit
Printer unit
Main control PCB
Data compression
Data rotation
Data expansion
SDRAM
HDD
DC controller PCB
Chapter 4
4-10
F-4-16
4.6.3 Flow of Image Data for the SEND Function0015-4369
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following is the flow of image data when the SEND function is in use.
F-4-17
4.6.4 Flow of Image Data for the Fax Transmission0015-4370
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following is the flow of image data when the fax transmission function is in use:
Image processing block for printer unit
Printer unit
Main controller PCB
Data compression
Data rotation
SDRAM
HDD
Image processing block for printer unit
Printer unit
Main controller PCB
Data rotation
Data expansion
Resolution conversion
SDRAM
HDD
To network
(compression data)
Ethernet port
Chapter 4
4-11
F-4-18
4.6.5 Flow of Image Data for the Fax Reception Function0015-4371
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following is the flow of image data when the fax reception function is in use:
F-4-19
Image processing block for reader unit
Image processing block for fax
Super G3 Fax Board
Resolution conversion
Main controller PCB
Compression
Compression
Expansion
SDRAM
HDD
Reader unit
Image processing block for printer unit
Image processing block for fax
Super G3 Fax Board
Main controller PCB
Data compression
Data rotation
Data expansion
SDRAM
HDD
DC controller PCB
Chapter 4
4-12
4.6.6 Flow of Image Data for the PDL Function0015-4372
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following is the flow of image data when the PDL function is in use:
F-4-20
Rendering processing block
Compression/expansion/editing block
Processing block for printer unit
DC controller PCB
Main controller PCB
SDRAM
HDD
Ethernet
PDL
Chapter 4
4-13
4.7 Parts Replacement Procedure
4.7.1 Main Controller Box
4.7.1.1 Before Removing the Main Controller Box0015-6362
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]
3) Detach the right cover (upper rear). (page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
4.7.1.2 Removing the Main Controller Box0015-4788
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the 7 connectors [4] of the video PCB [1].- 3 Wire saddle [2] (to free the harness)- 1 Reuse band [3]
F-4-212) Disconnect all the connectors of the main controller PCB, and detach the
main controller box [3].- 5 Edge saddle [1] (to free the harness)- 4 Screw [2]
F-4-22
4.7.2 Main Controller PCB
4.7.2.1 Before Removing the Main Controller PCB0015-6366
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]
3) Detach the right cover (upper rear). (page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
4.7.2.2 Removing the Main Controller PCB0015-4789
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the 4 screws [1].
F-4-232) Detach the reader relay PCB [1] from the main controller PCB.
F-4-243) Detach the Video PCB unit [3].
- Screw [1] 2pc.- Connector [2] 7pc.
[1][2]
[3]
[4]
[4]
[4]
[1][2]
[1] [1]
[1]
[2] [2][3]
[1]
[1]
[1]
Chapter 4
4-14
F-4-254) Disconnect all the connectors of the main controller PCB, and remove the
main controller PCB [2].- Screw [1] 8pc.
F-4-26
4.7.2.3 When Replacing the Main Controller PCB0016-0014
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Upload each setting/registration data stored in SRAM of the main controllerPCB onto the PC by using SST. See the chapter ‘Version Upgrading’ for itsoperation procedure.If you are replacing the main controller PCB, be sure to transfer the follow-ing components from the old to new PCB.
F-4-27[1] Boot ROM[2] Hard disk[3] Image memory (SDRAM)[4] Counter memory PCB
4.7.3 SDRAM
4.7.3.1 Before Removing the SDRAM0015-6371
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover.(page 10-17)Reference[Removingthe Main Controller Box Cover]
4.7.3.2 Removing the SDRAM0015-4791
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the 2 arms [1], and release the lock; then, detach the SDRAM [2].
F-4-28
4.7.4 Boot ROM
4.7.4.1 Before Removing the Boot ROM0015-6374
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper).(page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover.(page 10-17)Reference[Removingthe Main Controller Box Cover]
4.7.4.2 Removing the Boot ROM0015-4792
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the Boot ROM [1].
[1]
[1]
[2]
[2]
[2]
[3]
[1] [1]
[1]
[2]
[1]
[2]
[3]
[4]
[1] [1][2]
Chapter 4
4-15
F-4-29
4.7.5 HDD
4.7.5.1 Before Removing HDD0015-6378
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper).(page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover.(page 10-17)Reference[Removingthe Main Controller Box Cover]
4.7.5.2 Removing the HDD0015-4793
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the counter memory PCB [2].- 1 Screw [1]
F-4-30
Be sure to remove the counter memory PCB. If you hit the hard disk againstthe counter memory PCB, the impact can leave appreciable damage.
2) After detaching the hard disk [2] in the direction of the arrow, disconnectthe connector[3].- 2 Screw [1]
F-4-31
4.7.5.3 After Replacing the HDD0016-0004
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- Formatting the HDDStart up the machine in the safe mode (i.e., while holding down the 2 and 8keys, turn on the main power).Using the HD format function of the SST, format all partitions (BOOTDEV/PDLDEV/FSTDEV/FSTCDEV/TMP_GEN/TMP_FAX/TMP_PSS/
IMG_MNG/APL_MEAP/APL_GEN/APL_SEND). (For details, see the de-scriptions given for upgrading.)- Downloading the system softwareUsing the SST, download the following: System, Language, RUI, MEAP-CONT (Meap content), SDICT (OCR dictionary), KEY (key/certificate forencrypted communication), TTS (audio dictionary).
4.7.6 Video PCB
4.7.6.1 Before Removing the Video PCB0015-8243
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper).(page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover.(page 10-17)Reference[Removingthe Main Controller Box Cover]
4.7.6.2 Removing the Video PCB0015-8244
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the 7 connectors [4] of the Video PCB [1].- 3 Wire saddle [2] (to free the harness)- 1 Reuse band [3]
F-4-322) Detach the Video PCB [2].
- 2 Screw [1]
[1]
[1][2]
[1][2]
[3]
[1][2]
[3]
[4]
[4]
[4]
Chapter 4
4-16
F-4-33
4.7.7 Controller Fan
4.7.7.1 Before Removing the Controller Cooling Fan0015-6383
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
2) Detach the right cover (upper). (page 10-12)Reference[Removing theRight Cover (Upper)]
3) Remove the right door unit (upper). (page 10-34)Reference[Removingthe Right Door Unit (Upper)]
4.7.7.2 Removing the Controller Cooling Fan0015-4795
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the 1 connector [1], and free the fan harness from the clamp;then, detach the controller cooling fan [3].- 2 Screw [2]
F-4-34
[1]
[1]
[2]
[2]
[1] [3]
Chapter 5 Original Exposure System
Contents
Contents
5.1 Construction ...................................................................................................................................................................5-15.1.1 Specifications, Controls, and Functions....................................................................................................................................... 5-15.1.2 Major Components....................................................................................................................................................................... 5-15.1.3 Construction of the Control System............................................................................................................................................. 5-25.1.4 Reader Controller PCB ................................................................................................................................................................ 5-3
5.2 Basic Sequence ..............................................................................................................................................................5-45.2.1 Basic Sequence of Operations ..................................................................................................................................................... 5-45.2.2 Basic Sequence of Operation in Response to a Press on the Start Key ....................................................................................... 5-5
5.3 Various Control..............................................................................................................................................................5-55.3.1 Controlling the Scanner Drive System ........................................................................................................................................ 5-5
5.3.1.1 Overview .........................................................................................................................................................................................................5-55.3.1.2 Controlling the Scanner Motor........................................................................................................................................................................5-6
5.3.2 Enlargement/Reduction................................................................................................................................................................ 5-75.3.2.1 Changing the Magnification in Main Scanning Direction ..............................................................................................................................5-75.3.2.2 Changing the Magnification in Sub Scanning Direction ................................................................................................................................5-7
5.3.3 Controlling the Scanning Lamp ................................................................................................................................................... 5-85.3.3.1 Overview .........................................................................................................................................................................................................5-85.3.3.2 Scanning Lamp................................................................................................................................................................................................5-85.3.3.3 Controlling the Activation...............................................................................................................................................................................5-9
5.3.4 Detecting the Size of Originals .................................................................................................................................................... 5-95.3.4.1 Overview .........................................................................................................................................................................................................5-95.3.4.2 Points of Measurement Used for Original Size Identification ........................................................................................................................5-95.3.4.3 Overview of Operation..................................................................................................................................................................................5-10
5.3.5 Dirt Sensor Control .................................................................................................................................................................... 5-125.3.5.1 Dust Detection in Stream Reading Mode......................................................................................................................................................5-125.3.5.2 White Plate Dust Detection Control..............................................................................................................................................................5-13
5.3.6 Image Processing ....................................................................................................................................................................... 5-145.3.6.1 Overview .......................................................................................................................................................................................................5-145.3.6.2 CCD Drive ....................................................................................................................................................................................................5-155.3.6.3 CCD Output Gain Correction, Offset Correction .........................................................................................................................................5-155.3.6.4 CCD Output A/D Conversion .......................................................................................................................................................................5-155.3.6.5 Outline of Shading Correction ......................................................................................................................................................................5-155.3.6.6 Shading Adjustment ......................................................................................................................................................................................5-165.3.6.7 Shading Correction........................................................................................................................................................................................5-16
5.4 Parts Replacement Procedure.......................................................................................................................................5-175.4.1 CCD Unit ................................................................................................................................................................................... 5-17
5.4.1.1 Before Removing the CCD Unit ...................................................................................................................................................................5-175.4.1.2 Removing the CCD Unit ...............................................................................................................................................................................5-175.4.1.3 When Replacing the CCD Unit.....................................................................................................................................................................5-17
5.4.2 Copyboard glass......................................................................................................................................................................... 5-185.4.2.1 Removing the Copyboard Glass....................................................................................................................................................................5-185.4.2.2 When Replacing the Copyboard Glass .........................................................................................................................................................5-18
5.4.3 Scanning Lamp .......................................................................................................................................................................... 5-185.4.3.1 Before Removing the Scanning Lamp ..........................................................................................................................................................5-185.4.3.2 Removing the Scanning Lamp ......................................................................................................................................................................5-185.4.3.3 When Replacing the Scanning Lamp............................................................................................................................................................5-19
5.4.4 Reader Controller PCB .............................................................................................................................................................. 5-195.4.4.1 Before Removing the Reader Controller PCB ..............................................................................................................................................5-195.4.4.2 Removing the Reader Controller PCB..........................................................................................................................................................5-195.4.4.3 After Replacing the Reader Controller PCB.................................................................................................................................................5-20
5.4.5 Interface PCB............................................................................................................................................................................. 5-205.4.5.1 Before Removing the Interface PCB.............................................................................................................................................................5-205.4.5.2 Removing the Interface PCB ........................................................................................................................................................................5-20
Contents
5.4.6 Memory PCB ............................................................................................................................................................................. 5-215.4.6.1 Before Removing the Memory PCB............................................................................................................................................................. 5-215.4.6.2 Removing the memory PCB ......................................................................................................................................................................... 5-21
5.4.7 Inverter PCB .............................................................................................................................................................................. 5-215.4.7.1 Before removing the inverter PCB ............................................................................................................................................................... 5-215.4.7.2 Removing the Inverter PCB.......................................................................................................................................................................... 5-215.4.7.3 After Replacing the Inverter PCB................................................................................................................................................................. 5-22
5.4.8 Scanner Motor............................................................................................................................................................................ 5-225.4.8.1 Before Removing the Scanner Motor ........................................................................................................................................................... 5-225.4.8.2 Removing the Scanner Motor ....................................................................................................................................................................... 5-225.4.8.3 Mounting the Scanner Motor ........................................................................................................................................................................ 5-23
5.4.9 ADF Open/Close Sensor............................................................................................................................................................ 5-235.4.9.1 Before Removing the ADF Open/Close Sensor ........................................................................................................................................... 5-235.4.9.2 Removing the ADF Open/Close Sensor ....................................................................................................................................................... 5-23
5.4.10 Scanner HP Sensor................................................................................................................................................................... 5-235.4.10.1 Before Removing the Scanner HP Sensor .................................................................................................................................................. 5-235.4.10.2 Removing the Mirror Base HP Sensor ....................................................................................................................................................... 5-23
5.4.11 Original Size Sensor ................................................................................................................................................................ 5-245.4.11.1 Before Removing the Original Size Sensor ................................................................................................................................................ 5-245.4.11.2 Removing the original size sensor .............................................................................................................................................................. 5-24
5.4.12 Cooling Fan.............................................................................................................................................................................. 5-255.4.12.1 Before Removing the Cooling Fan ............................................................................................................................................................. 5-255.4.12.2 Removing the Cooling Fan ......................................................................................................................................................................... 5-25
5.4.13 Scanner Drive Cable ................................................................................................................................................................ 5-255.4.13.1 Outline ........................................................................................................................................................................................................ 5-255.4.13.2 Before Removing the Scanner Drive Cable................................................................................................................................................ 5-255.4.13.3 Removing the Scanner Drive Cable............................................................................................................................................................ 5-255.4.13.4 Fitting the Scanner Drive Cable.................................................................................................................................................................. 5-285.4.13.5 Adjusting the Position of the No. 1/No. 2 Mirror Base .............................................................................................................................. 5-28
5.4.14 Waste Toner Box Holder ......................................................................................................................................................... 5-295.4.14.1 Before Removing the Collecting Toner Bottle Holder ............................................................................................................................... 5-295.4.14.2 Removing the Collecting Toner Bottle Holder........................................................................................................................................... 5-29
Chapter 5
5-1
5.1 Construction
5.1.1 Specifications, Controls, and Functions0015-4373
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The specifications, controls, and functions of the machine's original exposure system are as follows:T-5-1
5.1.2 Major Components0015-4375
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The major components of the original exposure system are as follows:T-5-2
Item Description
Scanning lamp YG xenon lamp
Original scanning book mode: by moving the scanner
ADF mode: by moving original
Original reading resolution 600 x 600 dpi (main scanning x sub scanning)
Halftone 256 gradations
Scanning position detection by scanner HP sensor
lens single-focal point, fixed type
Magnification [1] in platen mode: 25% to 400%
main scanning direction: image processing by controller block
sub scanning direction: scanning speed variation (No. 1 mirror base; 100% or higher)in combination with image processing by reader block (50% or higher and lower than 100%)
in combination with image processing in reader block and controller block (lower than 50%)
[2] ADF mode: 25% to 200%
main scanning direction: image processing in controller block
sub scanning direction: original movement speed variation (50% or higher); in combination with image processing in controller block (lower than 50%)
Scanner drive control No. 1/2 mirror base: control by pulse motor
Scanning lamp control [1]activation control by pulse motor
[2]error detection control
Original size detection [1]book mode
sub scanning direction: by reflection type sensor
main scanning direction: by CCD
[2] ADF mode
main scanning direction: by slide guide in ADF
sub scanning direction: by photosensor in ADF
Item Notation Description
Scanning lamp LA1 xenon lamp (90,000 lx)
Scanner motor M501 2-phase pulse motor (pulse control)
Reader Cooling fan FM501 cools the reader block
ADF open/closed sensor 1 PS501 detects the state (open/closed) of the ADF; at 5 deg
Scanner HP sensor PS502 detects scanner home position
ADF open/closed sensor 2 PS503 detects the state (open/closed) of the ADF (detects timing of size detection at 25 deg)
Original size sensor (AB) --- detects the size in sub scanning direction (AB-configuration)
Original size sensor (inch) --- detects size in sub scanning direction (inch)
Interface PCB --- controls motor and fan, connects printer and ADF
Memory PCB --- data delivery between main controler and reader contoler/ADF
Mirror --- No. 1, 2, 3 mirrors
Inverter PCB --- drives the scanning lamp
CCD unit --- collects image data, performs analog image processing
Chapter 5
5-2
F-5-1
F-5-2
F-5-3
5.1.3 Construction of the Control System0015-4376
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The construction of the control system of the machine's original exposure system is as follows:
Reader controller PCB---
controls the reader unit as a whole, performs digital image processing
Item Notation Description
Memory PCB
Interface PCB
Scanning lamp
Reader cooling fan
Inverter PCB
CCD unit
Scanner HP sensorADF
open/closed sensor 2
Reader controller PCB
Original size sensor (inch)Original size
sensor (A/B)
Scanner motor
ADF open/closed sensor 1
Platen glass
Original
scanning lamp Lens CCDNo. 1 mirror
No. 1 mirror base
No. 2 mirror
No. 2 mirror baseNo. 3 mirror
HPImage leading edge
Size detectionStream reading position
(start position)
(forward)
(reverse)
Scanner motor
Light-blocking plate
No. 2 mirror base
scanning lamp
No. 1 mirror base
Scanner HP sensor
Chapter 5
5-3
F-5-4
5.1.4 Reader Controller PCB0015-4379
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The functional construction of the reader controller PCB is as follows:
J312
J305
J313
J303 J306
J309
J202
J205
J308
J201
J209
J310
J301
J204
J203J502
J503J505
J501
J315
J601
J602
J206
CCD unit
Scanner motorScanner motor control
Scanner HP sensor
ADF open/closed
sensor 1
ADF open/closed
sensor 2
Reader controller PCB
Interface PCB
To printer (main controller)
Reader cooling fan
To ADFTo printer
Reader controller PCB
Interface PCB
Memory PCB
To printer (main controller)
To DADF
Inverter PCB
Scanning lamp
Scanning lamp activation control
Chapter 5
5-4
F-5-5
T-5-3
T-5-4
5.2 Basic Sequence
5.2.1 Basic Sequence of Operations0015-4382
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Basic Sequence of Operation at Power-On
Jack Description
J201 used for input of power from the machine (printer unit)
J202 used for communication with the ADF (sensor signal input, fan control, scanner motor control, controller)
J203 used for communication with the printer unit; connects to the scanner motor; used for communication with the ADF; used for input of image signals
J204 used for connection with the CCD unit.
J205 used for communication with the CCD unit.
J206 used for connection with the inverter PCB.
J207 used for connection with the original size sensor (AB).
J208 used for connection with the original size sensor (inch).
J209 not usedJ210 not used.
IC Description
IC1 CPU (holds boot program)
IC2 ASIC (holds RAM)
IC3 flash ROM (stores firmware)
IC4 EEPROM (backs up service mode settings)
J203 J202
J210
J209
IC1(CPU)
IC2
J201
DF
J204J207J205J206 J208
IC3
Original size sensor (AB)
CCD unit
Inverter PCB
DC24VDC13VDC5VDC3.3V
Printer unit
Scanner motor
(not used)
(not used)
IC4
Original size sensor (inch)
(dotted line):back
Image processing (shading correction)
Storage of system software(flash ROM)
Backup of service mode settings
Chapter 5
5-5
F-5-6
5.2.2 Basic Sequence of Operation in Response to a Press on the Start Key0015-4384
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Basic Sequence of Operation in Response to a Press on the Start Key (book mode; 1 original)
F-5-7Basic Sequence of Operation in Response to a Press on the Start Key (ADF mode; 1 original)
F-5-8
5.3 Various Control
5.3.1 Controlling the Scanner Drive System
5.3.1.1 Overview0015-4387
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the components associated with the scanner drive system:
Reader motor
Scanning lamp
HP sensor
STBYSREADYReverseForward
Scanner unit positionHP
(shading position)
CCD output correction
- shift shading- fixed shading- white plate dust detection control- shading correction
HP (shading position)
Main power switch ON
Reader motor
Scanning lamp
HP sensor
Start key ON
STBYSTBY SREADY SCFW SCRWReverseForward
HP (shading position) HP (shading position)Image trailing edge
Platen board cover scan start position shift
White plate dust detection controlShading correction
Reader motor
Scanning lamp
HP sensor
Start keyON
STBYSTBY SREADY SCRW SCFWReverseForward
HP (shading)
HP (shading)Image trailing edge
Stream reading position shift
White plate dust detectionShading correction
Stream reading position
Stream reading dust detection
Shading position shift
White plate dust detection controlShading correction
Chapter 5
5-6
F-5-9[1] Scanner Motor M501 Drive Signalstarts/stops the motor; controls the direction and speed of its rotation[2] Scanner HP Detection Signaldetects the presence of the No. 1 mirror base at home position
5.3.1.2 Controlling the Scanner Motor0015-4389
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The configuration of the system used to control the scanner motor is as follows; the motor driver on the interface PCB operates according to the signals from theCPU to start/stop the scanner motor and to control the direction and speed of its rotation
F-5-10
1. Reverse Movement After a ScanAfter an image scan, the No. 1 mirror base is moved in reverse as far as the shading position at 234 mm/sec regardless of the selected magnification.
2. Forward Movement During a ScanDuring an image scan, the No. 1 mirror base is controlled at the speed indicated in the following figure; the No. 1 mirror base is moved forward at 325 mm/sec for100% magnification.
F-5-11
[1]
[2]
Reader controller
PCB
Interface PCB
(forward)
(reverse)
Scanner motor
Light-blocking plate
No.2 mirror base
Scanning lamp
No.1 mirror base
Scanner HP sensor
Reader controller PCB
Motor driver
Interface PCB
+24V/15V
J306A
A*B
B*
CPU
1
2
3
4
6
5
J308J307
J202J203
Scanner motor
M501[1]
[1] Scanner motor control signal
Start position
Acceleration
Image leading edge
Constant speed
Image trailing edge
Deceleration
Stop
Shift speed
Shift distance
[1] [2] [3] [4]
[1] Acceleration interval: accelerates up to scan speed [2] Run-up interval: run-up margin used to ensure stable speed[3] Image read interval: segment over which images are read[4] Deceleration interval: at the image trailing edge, decelerates and stops as soon as possible
HP
Chapter 5
5-7
ERROR CODE:E202 (HP detection error)-0001: when the No. 1 mirror base is moving forward, it fails to reach the HP sensor within a specific period of time
-0002: when the No. 1 mirror base is moving in reverse, it fails to reach the HP sensor within a specific period of time
SERVICE MODE:COPIER>ADJUST>ADJ-XY>ADJ-X (scanner image leading edge position adjustment)Enter a value to adjust the image leading edge position.settings range: 0 to 2970 (a change of '12' causes a shift of 1 mm)COPIER>AJST>ADJ-XY>ADJ-S (scanner home position)Do not change the setting.
5.3.2 Enlargement/Reduction
5.3.2.1 Changing the Magnification in Main Scanning Direction0015-4391
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To change the magnification in main scanning direction (for both platen and ADF modes), the machine reads the image at 100% and applies appropriate imageprocessing in the main controller block.
5.3.2.2 Changing the Magnification in Sub Scanning Direction0015-4393
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To change the magnification in sub scanning direction, the machine changes the speed at which it moves the scanner/original.For reduction, the machine also performs image data skipping (on main controller PCB and reader controller PCB).[1] In platen mode, the machine changes the speed at which the mirror base is shifted for a ratio between 25% and 400%.
T-5-5
The following shows the speeds at which the mirror base is moved:
F-5-12[2] In ADF mode, the machine changes the speed at which the original is moved for a ratio between 25% and 200%.
T-5-6
Description
25-49% increases the mirror base speed.collects image data at the same speed as for a ratio between 100% and 196%.uses data skipping on the reader controller PCB (50%)uses data skipping on the main controller PCB (50%)
50-99% increases the mirror base speed.e.g.: at 50%, reads images at twice the speed of 100%; also, uses data skipping on image data read at a ratio between 100% and 198% on the reader controller PCB (50%).
100% 325 mm/sec
101-200% decreases the mirror base speed.e.g., at 200%, collects images at 1/2 the speed for 100%.
201-400% decreases the mirror base speed.e.g., at 200%, collects images at 1/2 the speed for 100%.
Description
25-49% increases the speed used to move the original (as compared to 100%).collets image data at the same speed as for a ratio between 100% and 196%.uses data skipping on the main controller PCB (50%).
400%200%100%50%
1
1/21/4
speed ratio
Magnification25%
Chapter 5
5-8
The following shows the speeds at which the original is moved:
F-5-13
5.3.3 Controlling the Scanning Lamp
5.3.3.1 Overview0015-4395
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the items of control and the components of the control system associated with the activation of the scanning lamp:
1. Controlling the ActivationThe machine turns on or off the scanning lamp using the drive signal (XE-ON) generated by the CPU on the reader controller PCB. In response to the signal,the inverter PCB generates high-frequency high voltage in the activation motor circuit using the drive voltage (+24 V) supplied by the reader controller PCB,thus turning on the scanning lamp.
2. Detecting an ErrorThe machine identifies an error in the intensity of light as an activation error occurring when the lamp is initially turned on (shading correction).
ERROR CODE:E225-0001: at time of shading, the detected intensity of light falls short of a specific level.-0002: in ADF mode, the intensity of light between originals falls short of a specific level.
F-5-14
5.3.3.2 Scanning Lamp0015-4397
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's scanning lamp is a xenon lamp consisting of a tube in which xenon gas is sealed. On the inner side of the glass tube are 2 electrodes running parallelto the tube axis, while the inner side is coated with fluorescent material. When high-frequency high voltage is applied to the electrodes, the gas inside the tube startsto discharge, thus illuminating the fluorescent material.
50-99% increases the speed at which the original is moved.e.g., at 50%, collects the image at twice the speed for 100%.
100% 325 mm/sec
101-200% decreases the speed at which the original is moved.e.g., at 200%, collects image data at 1/2 the speed for 100%.
Description
200%100%50%
1
1/21/4
25%
2
Inverter PCBscanning lamp
Activation control circuit
J601 J206 Reader controller PCB
LA1CPU
GNDGNDGNDGND
XE-ON24V24V
XSYNC24V
123456789 1
23456789
Chapter 5
5-9
F-5-15
5.3.3.3 Controlling the Activation0015-4399
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine turns on or off the scanning lamp using the drive signal (XE_ON) from the CPU on the reader controller PCB. In response to the signal, the inverterPCB generates high-frequency high voltage in the activation control circuit using the drive voltage (+24 V) supplied by the reader controller PCB, thus turning onthe xenon lamp.
5.3.4 Detecting the Size of Originals
5.3.4.1 Overview0015-4401
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine identifies the size of an original with reference to the combination of measurements taken of the light reflected at specific points of the CCD and theoutput of a reflection type sensor. It takes measurements at 2 points for individual sizes to ensure correct identification even in the event that the original is displacedwhile the ADF is being closed.
- for main scanning direction, by the CCD (for AB, 8 points; for inch-configuration, 6 points)- for sub scanning direction, by a reflection type photosensor (for AB-configuration, 1 point; for inch-configuration, 1 point)
The machine identifies the size of an original as follows:1) External Light (main scanning direction only)
While keeping the scanning lamp off, the machine measures the CCD level at individual points of measurement in main scanning direction.2) Sensor Output Level
The machine turns on the scanning lamp, and measures the CCD level at individual points of measurement in main scanning direction. Also, the machine turnson the LED of the reflection type photosensor in sub scanning direction to measure the sensor output. It uses the combination of the measurement and the outputto identify the size of the original in question.
5.3.4.2 Points of Measurement Used for Original Size Identification0015-4403
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
For main scanning direction, the machine moves the No. 1 mirror base to the point of CCD original detection to measure the CCD level at individual points ofmeasurement. For sub scanning direction, the machine uses the outputs of original sensors 1 and 3.
F-5-16
1. Checking the Presence/Absence of an Original at 2 Points (individual points of detection)For main scanning direction, the machine identifies the presence/absence of an original with reference to the CCD output at 2 points (nearest).
F-5-17
Fluorescent material
Electrode
Opening
Electrode
ElectrodeElectrode
Glass tube
Point of original detection 3Point of original detection 4
Point of original detection 1
Print of original detection 2
B5
B6
A5
A4
B5R
A4R
B4
A3
CCD original detection position
Point of original detection 2
Point of original detection 1
Point of original detection 3
LTRRSTMT
LTR
LGL
279.4×431.8mm(11"×17")
CCD original detection position
Original sensor 3
AB-Configuration Inch-configuration
STMTR
Original sensor 1
Near 4-mm point
Near 13-mm point1A = additional detection point 1
Original size border line
Original size border line
1B = additional detection point 2
Chapter 5
5-10
T-5-7
Note:Change in the Signal in Response to ADF Open -> Closedchange present: noother: yesThe OR argument is applied to the outputs at 2 points.
2. Priority on the Presence of an Original at the FrontIf the machine detects the absence of an original at the rear in spite of detection of the presence at the front for main scanning direction, the machine will identifythe size of the original upholding the result of detection at the front.
F-5-18EX (B5 original)
T-5-8
5.3.4.3 Overview of Operation0015-4405
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1. In a Wait StateNo. 1 mirror base: at shading positionscanning lamp: offoriginal sensor
Result of movementResult of identification
A B
no no original absent
yes no original present
no yes original present
yes yes original present
Point of detection Result of detectionpresent/absent
Result of identification
1 present present
2 absent present
3 present present
4 absent absent
B5
Document size
sensor 1
CCD original detection position
Point of detection 1
Point of detection 4
Point of detection 3
Point of detection 2
B5
(rear)
(front)
Chapter 5
5-11
F-5-192. ADF Being Opened
No.1 mirror base: moves to a specific point of original detectionscanning lamp: offoriginal sensor: off
F-5-203. ADF Being Closed
No. 1 mirror base: at point of original detectionscanning lamp: off -> onoriginal sensor: original detection operation- When the ADF is at 25 deg or lower, the external light within the width of any original is kept out of external light, thus causing the machine to assume the
absence of an original at points of external light detection (external light search operation). The ADF open/closed sensor 2 identifies the state as being "closed," and the machine starts original size detection.Here, B5, B4, A4, and A3 are eliminated from the list of possible sizes.- When the external light search is over, the machine turns on the xenon lamp for the main scanning lamp, and checks the CCD (4 points) for external light. For
sub scanning direction, the machine starts to operate the original sensor.
F-5-21
F-5-224. ADF Fully Closed (5 deg or less)
No. 1 mirror base: at point of original detectionscanning lamp: onoriginal sensor: original detection operationThe machine looks for a change in the output level of individual sensors for a period of 2 sec after the ADF open/closed sensor 1 has identified the current stateas being "closed." The absence of a change in the level causes the machine to assume the presence of an original at the point in question.The machine uses the combination of changes in the levels of 5 points to identify the size of the original in question.
F-5-235. In a Wait State (for a press on the Start key)
No.1 mirror base: at point of original detectionscanning lamp: offoriginal sensor: off
F-5-24
CCD point of original detection
Scanning lamp
Original sensor
Reader unit
ADFPoint of detection 1Point of detection 2Point of detection 3Point of detection 4
Platen glass
(external light)
(external light)
25
5
Chapter 5
5-12
F-5-25
5.3.5 Dirt Sensor Control
5.3.5.1 Dust Detection in Stream Reading Mode0015-4409
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine uses the dust detection control mechanism to check for dust on the platen glass and the ADF platen roller, thus preventing reproduction of dust, if any,in output images.
1. Timing of Control- at the end of a job- between sheets (for every sheet)
F-5-26 *Executed only if dust has been detected at all points (A, B, C, D, E) during the previous job. In such a case, the machine will use the point subjected to least dust,
and executes correction before starting a read operation.
2. Particulars of Control- At the End of a Job (changing the stream reading dust read position)
The machine measures the light reflected by the surface of the platen roller, and detects the presence/absence of dust with reference to its intensity. If the presenceof dust is detected, the machine moves to the next point (5 points max.; A -> B -> C -> D -> E).The machine uses the first point at which the absence of dust is detected as the read point for the next job.
1A B
2A B
3A B
4A B
1A B
2A B
3A B
Original
size
A3
B4
A4R
A4
B5
B5R
A5
B6
none
Original
sensor 1
CCD point
of detection
AB-Configuration
Original
size
11"x17"
LGL
LTRR
LTR
STMTR
STMT
absent
CCD point
of detection
Inch-configuration
change absent :change present
Original
sensor 3
Dust detection control* Dust detection control
Dust detection control
Start keyON
1stSCAN
2ndSCAN
Chapter 5
5-13
F-5-27If dust is detected at all 5 points (A, B, C, D, E), the machine will issue an alert in response to the placement of an original in the ADF, thus promoting the user toclean the points.Alert Message:The machine may read the dust, which may show as lines in the output image. Clean the narrow segment of glass indicated in the drawing with a soft cloth moistenedwith water (and well wrung).Press the Close button to reset the alert.At the start of a job, the machine executes dust detection once again, and will use a point with little or no dust as the read point.*1: read point at the end of the previous job.*2: point with little or no dust.
T-5-9
- Between Sheets (dust correction)The machine does not move the scanning lamp on account of dust detection.If dust is detected between sheets, the machine corrects the fact with reference to the pixels on both sides of the area of dust.
SERVICE MODE:COPIER>OPTION>BODY>DFDST-L1 (level 1)use it to adjust dust detection level between sheetsCOPIER>OPTION>BODY>DFDST-L2 (level 2)use it to adjust dust detection level at the end of a job
5.3.5.2 White Plate Dust Detection Control0015-4410
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The white plate can collect stray dust inside the reader unit, causing lines in images, and the machine is equipped with a mechanism to check for dust on the plateand correct it to limit its effects on output images.
1. Timing of Control(1) Before a Job
(a) white plate dust detection(b) white plate dust correction
(2) After a Job(a) white plate dust detection(b) white plate dust correction
A read reference point (1.0 mm to the left from the center of the platen roller)
B point 1.0 mm to the left from the reference point
C point 0.5 mm to the left from the reference point
D point 0.5 mm to the right for the reference point
E point 1.0 mm to the right from the reference point (center of platen roller)
A D E
pattern 1
pattern 2
pattern 3
pattern 4
pattern 5
At the start of a job
At the end of a job
0.5mm
B C
0.5mm0.5mm0.5mm
*2
*1
*1
*1
Chapter 5
5-14
F-5-28
2. Particulars of Control- White Plate Dust DetectionThe machine compares the data on the light reflected by the white plate at time of fixed shading and shift shading to check for dust on the white plate while at thesame time identifying the coordinates and width of the area of dust.- White Plate Dust CorrectionIf the machine detects the presence of dust, it corrects the shading correction coefficient of the area of dust by means of a correction coefficient used for both sidesof the area with dust, thus limiting the effects of the dust.
F-5-29
5.3.6 Image Processing
5.3.6.1 Overview0015-4411
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The PCBs used in the image processing system have the following functions:
CDD/AP PCB: CCD drive, analog image processing, A/D conversionReader controller PCB: shading correction
F-5-30
1. Analog Image processing- CCD drive- CCD output gain correction, offset correction- CCD output A/D conversion
Dust detection control Dust detection control
Start keyON
1stSCAN
2ndSCAN
Correction Algorithm
Data on light reflected by the white plate (shift shading))
Data on light reflected by the white plate (fixed shading)
Identifies the coordinates of the start of dust and width
The machine corrects the correction coefficient of the area of dust using data for areas on both sides
Point of white plate data measurement at time of fixed shading
White plate data correction area at time of shift shading
White plate
Dust
Comparison
CCD/AP PCB
Reader controller PCB
CCD
A/D conversion Shading processing
Analog image processing
Analog image processing block
Controller block
Digital image processing block
Chapter 5
5-15
F-5-31
2. Digital Image Processing- shading correction
F-5-32
5.3.6.2 CCD Drive0015-4412
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1. CCD The CCD used in the machine is a 1-line linear image sensor. - Number of pixels: 7450 - Size of a pixel: 4.7 x 4.7 ym
2. CCD DriveThe signals converted by the light-receiving block are sent out in 2 analog video signal channels (even-numbered pixels, odd-numbered pixels).
F-5-33
5.3.6.3 CCD Output Gain Correction, Offset Correction0015-4413
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine processes the analog video signals from the CCD so that the rate of their amplitude is a specific level. The machine also makes sure that the outputvoltage in the absence of incident light is of a specific level (offset correction).
5.3.6.4 CCD Output A/D Conversion0015-4414
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The odd-numbered and even-numbered pixel analog video signals after correction are further converted into 10-bit digital signals representing specific pixel voltagelevels by the A/D converter.
5.3.6.5 Outline of Shading Correction0015-4416
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine executes shading correction so that the CCD output will be even when the density of the original is even.
CCD (1 line each for R, G, and B)
Analog image signal
Analog image process
- gain correction- offset correction
A/D conversion
CCD drive control
A12V
A5V
J101 J204
J204
J102 J205
CCD control signal
Gain correction data
Digital image signal
Reader controller
PCB
Odd-numbered pixel
Odd-numbered pixels
Even-numbered pixels
CCD/AP circuit
10
Even-numbered pixel
Gain correction data
EEP-ROM
SRAM
CPU
Shading correction
Digital image signal
CCD/AP PCB
Reader controller PCB
10
Digital image signal
8
Target value
J101
J102
J204
J205J203
Shift register
Light-receiving block(photo diode)
Shift register
Output buffer
Output buffer
Gate
Gate
123456
Odd-numbered pixel data
Even-numbered pixel data
Chapter 5
5-16
The output of the CCD may not necessarily be even because of the following factors even if the density of the original is perfectly even:(1) variation in the sensitivity of the individual pixels of the CCD(2) difference in the degree of light passing through the center of the lens and through its edge(3) difference in the intensity of light between the center and ends of the scanning lamp(4) deterioration of the scanning lamp
The machine executes shading correction to make up for the variation in the output of the CCD.Shading correction may be shading adjustment executed to determine a service mode target value or shading correction executed for every job.
5.3.6.6 Shading Adjustment0015-4418
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
In shading adjustment, the machine measures the density of a white sheet of paper and the standard white plate, and stores the measurements in memory. The ma-chine then computes these measurements for use as the target value for shading correction. Shading adjustment is executed at time of machine installation or scan-ning lamp replacement, or when a change has occurred in the intensity of light over time.
Service Mode:COPIER>FUNCTION>CCD>CCD-ADJ
5.3.6.7 Shading Correction0015-4420
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine executes shading correction for every scan of an original.The machine shines the light of the scanning lamp against the standard white plate, and measures the light reflected by the plate; it then uses the analog imageprocessing block of the CCD/AP PCB to turn the measurements into digital data, which will be sent to the shading correction circuit of the reader controller PCBin the form of a shading coefficient.In the shading correction circuit, the shading coefficient is compared against the target value stored in memory, and the machine uses the differences as the shadingcorrection value.The shading correction value is used to make up for the variation among individual pixels of the CCD occurring at each scan, thus evening out the image densitylevel.
F-5-34
CCD output
Original densityStandard white plate
Characteristics before correction
Target value
Measurement
Characteristics after correction
White
Chapter 5
5-17
5.4 Parts Replacement Procedure
5.4.1 CCD Unit
5.4.1.1 Before Removing the CCD Unit0015-4798
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the copyboard glass. (page 5-18)Reference[Removing theCopyboard Glass]
5.4.1.2 Removing the CCD Unit0015-4801
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the CCD unit cover [2].- 9 Screw [1]
F-5-35
F-5-362) Slide the original size detection unit [2].
- 3 Screw [1]
F-5-373) Detach the original size sensor unit [2].
- 1 connector [1]
F-5-384) Detach the CCD unit [4] of the reader controller PCB.
- 2 Flat cable [1]- 2 Screw [2]- 2 Leaf spring [3]
F-5-39
How to disconnect the flat cableSlide the locking lever [1] in the direction of the arrow to release; then, dis-connect the flat cable [2].
F-5-40
5.4.1.3 When Replacing the CCD Unit0015-9939
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Perform the following steps after replacing the CCD unit.
1) Enter the correction values to be described on the label included in theCCD unit (the 2 following items) in the service mode.- COPIER > ADJUST > CCD > DFCH2G2- COPIER > ADJUST > CCD > DFCH2G10
2) Transcribe the above correction values to the service label at the back ofthe front cover of the host machine.
3) Execute the following in the service mode.3-1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ)
[1]
[1]
[2]
[1]
[1]
[2]
���
���
[1]
[2]
[2]
[3]
[4]
[1][1]
[2]
Chapter 5
5-18
3-2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-WLVL1/2)
Be sure to perform white plate data adjustment before performing ADFwhite level plate.
5.4.2 Copyboard glass
5.4.2.1 Removing the Copyboard Glass0015-4803
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the ADF.2) Remove the 2 screws [1], and detach the right glass retainer [2]; then, de-
tach the copyboard glass [3].
F-5-41
- When detaching the copyboard glass, take care not to touch the whiteplate attached to its back. Soiling can cause lines in the image. If soiled,clean it using lint-free paper moistened with alcohol.- Take care not to deform the sponge [2] attached to the right glassretainer [1].
F-5-42
5.4.2.2 When Replacing the Copyboard Glass0015-9949
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Execute the following in the service mode:1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ)2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-
WLVL1/2)
Be sure to perform white plate data adjustment before performing ADFwhite level adjustment.
5.4.3 Scanning Lamp
5.4.3.1 Before Removing the Scanning Lamp0015-6406
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the copyboard glass.(page 5-18)Reference[Removing the Copy-board Glass]
2) Detach the right cover (upper). (page 10-12)Reference[Removing the
Right Cover (Upper)]3) Detach the reader right cover. (page 10-17)Reference[Removing the
Reader Right Cover]4) Detach the left cover (upper). (page 10-12)Reference[Removing the
Left Cover (Upper)]5) Detach the reader left cover. (page 10-17)Reference[Removing the
Reader Left Cover]6) Detach the reader front cover. (page 10-17)Reference[Detaching the
Reader Front Cover]7) Detach the reader rear cover. (page 10-18)Reference[Detaching the
Reader Rear Cover]
5.4.3.2 Removing the Scanning Lamp0015-4813
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the CCD unit cover [2].- 9 Screw [1]
F-5-43
F-5-442) Free the cable [2] from the cable guide [3].
- 1 Connector [1]- 1 Reuse band [4]
3) Open the ferrite core [5] to detach.
F-5-45
When replacing the scanning lamp, be sure to fit the removed ferrite core to
[1]
[2]
[3]
[1]
[2]
[1]
[1]
[2]
[1]
[1][2]
[3][4]
[5]
Chapter 5
5-19
the new lamp.
4) Slide the No. 1 mirror base [1] to the right so that it matched against thecut-off [2] of the frame.
When detaching the No. 1 mirror base, be sure to hold it by the bend [A] onthe mirror stay.
F-5-465) Detach the scanning lamp [2].
- 2 Screw [1]
F-5-47
5.4.3.3 When Replacing the Scanning Lamp0015-9955
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Execute the following in the service mode:1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ)2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-
WLVL1/2)
Be sure to perform white plate data adjustment before performing ADFwhite level adjustment.
5.4.4 Reader Controller PCB
5.4.4.1 Before Removing the Reader Controller PCB0015-4816
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the copyboard glass.(page 5-18)Reference[Removing the Copy-board Glass]
5.4.4.2 Removing the Reader Controller PCB0015-4823
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the CCD unit cover [2].- 9 Screw [1]
F-5-48
F-5-492) Slide the original size detection unit [2].
- 3 Screw [1]
F-5-503) Detach the original size sensor unit [2].
- 1 Connector [1]
[1]
[2]
[2]
[A]
[1]
[1]
[2]
[1]
[1]
[2]
[1]
[1]
[2]
Chapter 5
5-20
F-5-514) Detach the reader controller PCB [4].
- 5 Flat cable [1]- 1 Connector [2]- 4 Screw [3]
F-5-52
How to disconnect the flat cableSlide the locking lever [1] in the direction of the arrow to release; then, dis-connect the flat cable [2].
F-5-53
5.4.4.3 After Replacing the Reader Controller PCB0015-9935
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure to generate the latest P-PRINT printout before replacing the readercontroller PCB.- If you are initializing the RAM on the reader controller without replacingthe PCBUsing the SST, upload the backup data of R-CON; initialize the RAM, andthen download the data, thus eliminating the need for the following.
1) Using the SST, download the latest system software (R-CON).2) Make the following selections in the service mode: COPIER > FUNC-
TION > CLEAR > R-CON. Then, press the OK key to execute RAM in-itialization. Thereafter, turn off and then back on the main power.
3) Enter the appropriate settings for the following items in the service mode:a. setting indicated on the service label (found behind the reader unit front
cover)a-1. image read start position adjustment (X direction; in fixed readingmode)
COPIER>ADJUST>ADJ-XY>ADJ-Xa-2 image read start position adjustment (Y direction; in fixed readingmode)
COPIER>ADJUST>ADJ-XY>ADJ-Ya-3 shading position adjustment (in fixed reading mode)
COPIER>ADJUST>ADJ-XY>ADJ-Sa-4 feeder mode main scanning position adjustment
COPIER>ADJUST>ADJ-XY>ADJ-Y-DFa-5 ADF stream reading CCD reading position
COPIER>ADJUST>ADJ-XY>STRD-POSa-6 density manipulating value adjustment
COPIER>ADJUST>CCD>DFCH-G2COPIER>ADJUST>CCD>DFCH-G10(After inputs it, execute COPIER>FUNCTION>DF-LNR)
The machine retains ADF-related service data in the RAM of its reader con-troller.ADF adjustment is necessary whenever you have replaced the reader con-troller or initialized the RAM.
b. original stop position adjustment (X direction) (stream reading)FEEDER>ADJSUT>DOCST
c. original feed speed (magnification) adjustmentFEEDER>ADUST>LA-SPEED
4) Make adjustments using the following service mode items:a. ADF sensor sensitivity adjustment
FEEDER>FUNCTION>SENS-INTb. tray width adjustment
FEEDER>FUNCTION>TRY-A4 FEEDER>FUNCTION>TRY-A5RFEEDER>FUNCTION>TRY-LTRFEEDER>FUNCTION>TRY-LTRR
c. white plate data adjustmentCOPIER>FUNCTION>CCD>CCD-ADJ
d. ADF white level adjustmentCOPIER>FUNCTION>CCD>DF-WLVL1COPIER>FUNCTION>CCD>DF-WLVL2
Be sure to perform white plate data adjustment before performing ADFwhite level adjustment.
After having made the foregoing adjustments, put the P-PRINT printout inthe service book case, replacing the previous P-PRINT printout.
5.4.5 Interface PCB
5.4.5.1 Before Removing the Interface PCB0015-4825
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the reader rear cover. (page 10-18)Reference[Detaching theReader Rear Cover]
5.4.5.2 Removing the Interface PCB0015-4827
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the interface PCB mount [4].- 9 Connector [1]- 1 Flat cable [2]- 9 Screw [3]
F-5-54
���
���
[1]
[2]
[3] [3]
[1][3] [3]
[4]
[1][1]
[2]
[1]
[1]
[1] [2]
Chapter 5
5-21
F-5-55
How to disconnect the flat cableSlide the locking lever [1] in the direction of the arrow; then, disconnect theflat cable [2].
F-5-56
3) Detach the interface PCB [2].- 6 Screw [1]
F-5-57
5.4.6 Memory PCB
5.4.6.1 Before Removing the Memory PCB0015-9366
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the reader rear cover. (page 10-18)Reference[Detaching theReader Rear Cover]
2) Detach the interface PCB. (page 5-20)Reference[Removing the Inter-face PCB]
5.4.6.2 Removing the memory PCB0015-9364
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the memory PCB mount [4].- 1 Connector [1]- 1 Flat cable [2]- 5 Screw [3]
F-5-58
F-5-592) Detach the memory PCB [2].
- 10 Screw [1]
F-5-60
5.4.7 Inverter PCB
5.4.7.1 Before removing the inverter PCB0015-4829
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the copyboard glass.(page 5-18)Reference[Removing the Copy-board Glass]
5.4.7.2 Removing the Inverter PCB0015-4831
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the CCD unit cover [2].- 9 Screw [1]
[3]
[3]
[4]
[1][1]
[2]
[1]
[1]
[2]
[1] [2]
[3]
[3] [4]
[1]
[1]
[2]
Chapter 5
5-22
F-5-61
F-5-622) Detach the inverter PCB [5].
- 1 Connector [1]- 1 Flat cable [2]- 1 Screw [3]- 2 PCB support [4]
F-5-63
How to disconnect the flat cableSlide the locking lever [1] in the direction of the arrow; then, disconnect theflat cable [2].
F-5-64
5.4.7.3 After Replacing the Inverter PCB0015-9958
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Execute the following in the service mode.1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ).2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-
WLVL1/2).
Be sure to perform white plate data adjustment before performing ADFwhite level plate.
5.4.8 Scanner Motor
5.4.8.1 Before Removing the Scanner Motor0015-4834
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the reader rear cover. (page 10-18)Reference[Detaching theReader Rear Cover]
5.4.8.2 Removing the Scanner Motor0015-4836
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Pull out the cover [2].- 4 Screw [1]
F-5-652) Remove the 2 reuse bands [2] from the cover [1].
F-5-663) Move the scanner motor [3] in the direction of the arrow to pull out.
- 3 Screw [1]- 2 Spring [2]
[1]
[1]
[2]
[1]
[1]
[2]
[5][3]
[4][4]
[1] [2]
[1]
[1] [2]
Chapter 5
5-23
F-5-674) Detach the scanner motor [2].
- 1 Connector [1]
F-5-68
5.4.8.3 Mounting the Scanner Motor0015-4837
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When mounting the scanner motor, check to make sure that the timing belt[3] is properly fitted to the scanner pulley [1] and the motor shaft [2].
F-5-69
F-5-70
5.4.9 ADF Open/Close Sensor
5.4.9.1 Before Removing the ADF Open/Close Sensor0015-4838
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the reader rear cover. (page 10-18)Reference[Detaching theReader Rear Cover]
5.4.9.2 Removing the ADF Open/Close Sensor0015-4839
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the connector [1].
F-5-712) Detach the reinforcing plate [2].
- 4 Screw [1]
F-5-723) Detach the ADF open/close sensor (1, 2).
- Hook [1]
F-5-73
5.4.10 Scanner HP Sensor
5.4.10.1 Before Removing the Scanner HP Sensor0015-4840
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the ADF.2) Detach the reader rear cover. (page 10-18)Reference[Detaching the
Reader Rear Cover]
5.4.10.2 Removing the Mirror Base HP Sensor0015-4841
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1][2]
[2][1]
[3]
[2]
[1]
[1][3]
[3][2]
[1]
[2]
[1]
[1]
[2]
[1]
[1]
Chapter 5
5-24
1) Detach the reinforcing plate [2].- 4 Screw [1]
F-5-742) Detach the sensor base [2].
- 1 Screw [1]
F-5-753) Detach the home position sensor [1].
- 1 Connector [1]
F-5-764) Detach the home position sensor [2].
- Hook [1]
F-5-77
5.4.11 Original Size Sensor
5.4.11.1 Before Removing the Original Size Sensor0015-4842
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the copyboard glass.(page 5-18)Reference[Removing the Copy-board Glass]
5.4.11.2 Removing the original size sensor0015-4845
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the CCD unit cover [2].- 9 Screw [1]
F-5-78
F-5-792) Shift the original size sensor unit [2].
- 3 Screw [1]
F-5-803) Detach the original size sensor unit [2].
- 1 Connector [1]
[1]
[1]
[2]
[1]
[2]
[1]
[2]
[3]
[1][1]
[2]
[1]
[1]
[2]
[1]
[1]
[2]
Chapter 5
5-25
F-5-814) While freeing the claw at the edge, remove the original size sensor [1].
F-5-82
5.4.12 Cooling Fan
5.4.12.1 Before Removing the Cooling Fan0015-4846
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the reader rear cover. (page 10-18)Reference[Detaching theReader Rear Cover]
5.4.12.2 Removing the Cooling Fan0015-4847
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the wire saddle [1], and disconnect the connector [2].2) Detach the cooling fan [4].
- 2 Screw [3]
F-5-83
5.4.13 Scanner Drive Cable
5.4.13.1 Outline0015-4848
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure to have the following nearby when replacing the scanner drive cable:- mirror positioning tool
5.4.13.2 Before Removing the Scanner Drive Cable0015-4849
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the copyboard glass. (page 5-18)Reference[Removing theCopyboard Glass]
2) Detach the right cover (upper). (page 10-12)Reference[Removing theRight Cover (Upper)]
3) Detach the reader right cover. (page 10-17)Reference[Removing theReader Right Cover]
4) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
5) Detach the reader left cover. (page 10-17)Reference[Removing theReader Left Cover]
6) Detach the reader front cover. (page 10-17)Reference[Detaching theReader Front Cover]
7) Detach the reader rear cover. (page 10-18)Reference[Detaching theReader Rear Cover]
8) Detach the ADF.9) Detach the control panel. (page 10-23)Reference[Removing Control
Panel]
5.4.13.3 Removing the Scanner Drive Cable0015-4859
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the stream reading glass retainer [2].- 2 Screw [1]
When detaching the stream reading glass retainer, be sure to take care so thatthe leaf spring will not come off.
2) Remove the stream reading glass [3].3) Detach the left glass retainer [5].
- 2 Screw [4]
F-5-84
- When mounting the stream reading glass retainer, be sure to hold downboth edges of the leaf spring [A] while fixing it in place. (Take care notto bend the leaf spring.)- Be sure to mount it while butting the stream reading glass retainer [B]against the stream reading glass [C].- Check to be sure that the side of the stream reading glass in contact withthe leaf spring [D] of the stream reading glass retainer.- If not, dust can collect on the stream reading glass, causing lines inoutput images.
���
���
[1]
[2] [1] [3]
[4]
[1]
[2]
[3] [4]
[4]
[5]
Chapter 5
5-26
F-5-85
F-5-864) Detach the ADF right screw cover [2].
- 1 Screw [1]
F-5-875) Detach the ADF left screw cover [2].
- 1 Screw [1]
F-5-886) Detach the interface PCB mount [4].
- Connector [1] 9pc.- Flat cable [2] 1pc.- Screw [3] 9pc.
F-5-89
F-5-907) Detach the memory PCB mount [4].
- Connector [1] 1pc.- Flat cable [2] 1pc.- Screw [3] 5pc.
F-5-91
[A]
[B]
[C] [D]
[1] [2]
[1][2]
[1]
[1]
[1] [2]
[3]
[3]
[4]
[1] [2]
Chapter 5
5-27
F-5-928) Open the 2 wire saddles [1].9) Detach the motor cover [3] together with the harness.
- Screw [2] 4pc.
F-5-9310) Free the harness from the wire saddle [1], and detach the motor frame [3].
- 6 Screw [2]
F-5-9411) Disconnect the connectors [1] of the reader unit communication cable.
F-5-9512) Shift the reinforcing plate [2] to the front.
- 4 Screw [1]
F-5-9613) Free the harness from the wire saddle [3].
- 2 Connector [1]- 1 Snap band [2]
F-5-9714) Free the harness from the 3 wire saddles [1], and detach the ADF open/
close sensor base [3].- 6 Screw [2]
F-5-9815) Detach the reader upper frame [2].
- 24 Screw [1]
[3]
[3] [4]
[1][3][2]
[2]
[1][2][2]
[2]
[3]
[1]
[1]
[1]
[2]
[1][2] [3]
[1]
[1]
[1][2] [2][2]
[2][3]
Chapter 5
5-28
F-5-99
In the next steps, draw mark-off lines before removing the screw.
16) Remove the 2 cable fixing screws [2] of the No. 1 mirror base [1].17) Remove the cable fixing spring [3].18) Free the 2 hooks [4] of the cable from the right side of the reader unit
frame.19) Detach the cable for the pulleys.
F-5-100
5.4.13.4 Fitting the Scanner Drive Cable0015-4860
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Put the ball of the cable into the hole of the drive pulley [1], and wind thecable (4 times inside; 5 times outside); then, tape it in place. At this time,make sure that the cable fixing [2] is on the inside.
2) Fit the cable on the pulleys; then, fit one end on the left side hook [3] andthe other end on the right side hook [4].
3) Temporarily fix the cable fixing plate [2] in place on the No. 1 mirror base[5].
4) Mount the reader unit upper frame.
F-5-101
F-5-102
5.4.13.5 Adjusting the Position of the No. 1/No. 2 Mirror Base
0015-9945
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Arrange the mirror positioning tool (FY9-3009-040) so that it is ready foruse in the machine (by changing the pin position; REAR).
[1] [1][1]
[1][1]
[2]
[1]
[2]
[2]
[4]
[4]
[1]
[3]
[4]
[4]
[5]
[3][3]
[1]
[1]
[2]
[2]
[4]
[4]
[5]
Chapter 5
5-29
F-5-1032) Arrange the mirror positioning tool so that it is ready for use in the ma-
chine (by changing the pin position; FRONT).
F-5-1043) Fit the pins of the mirror positioning tool (front [2]; rear [3]) into the ap-
propriate holes [1] of the No. 1/No. 2 mirror base.
F-5-105
F-5-1064) Secure the end of the cable that has temporarily been fixed in place on the
hook of the reader unit frame.5) Fully tighten the screws on the cable fixing plate both at the front and the
rear.6) Detach the mirror positioning tool (FRONT, REAR).7) Put the detached parts back on by reversing the foregoing steps.
5.4.14 Waste Toner Box Holder
5.4.14.1 Before Removing the Collecting Toner Bottle Holder
0015-9424
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Detach the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
5.4.14.2 Removing the Collecting Toner Bottle Holder0015-9425
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the collecting toner bottle.2) Move the main power switch base [3] to the side.
- 2 Screw [1]- 2 Wire saddle [2] (to free the harness)
F-5-1073) Detach the connector base [3].
- 5 Connector [1]- 2 Screw [2]
[A][B]
[C]
[B]
[A]
[A][B]
[C]
[B]
[A]
[1]
[3]
[2]
[1] [1]
[2]
[3]
Chapter 5
5-30
F-5-1084) Detach the collecting toner bottle holder [2].
- 2 Screw [1]
Take care not to spill the collecting toner.
F-5-109
[2]
[1][1]
[1]
[1]
[2]
Chapter 6 Laser Exposure
Contents
Contents
6.1 Construction ...................................................................................................................................................................6-16.1.1 Overview...................................................................................................................................................................................... 6-16.1.2 Major Components....................................................................................................................................................................... 6-1
6.2 Basic Sequence ..............................................................................................................................................................6-26.2.1 Basic Sequence of Operation (laser exposure) ............................................................................................................................ 6-2
6.3 Various Controls ............................................................................................................................................................6-26.3.1 Controlling the Laser Activation Timing..................................................................................................................................... 6-2
6.3.1.1 Generating the Sync Signal .............................................................................................................................................................................6-26.3.1.2 Flow of the Sync Signal ..................................................................................................................................................................................6-2
6.3.2 Controlling the Intensity of Laser Light ...................................................................................................................................... 6-26.3.2.1 Controlling the Laser Intensity........................................................................................................................................................................6-26.3.2.2 APC Control....................................................................................................................................................................................................6-3
6.3.3 Controlling the Laser Scanner Motor .......................................................................................................................................... 6-46.3.3.1 Controlling the Laser Scanner Motor..............................................................................................................................................................6-4
6.4 Parts Replacement Procedure.........................................................................................................................................6-56.4.1 Laser Scanner Unit....................................................................................................................................................................... 6-5
6.4.1.1 Removing the Laser Scanner Unit ..................................................................................................................................................................6-56.4.1.2 When Replacing the Laser Scanner Unit ........................................................................................................................................................6-5
Chapter 6
6-1
6.1 Construction
6.1.1 Overview0015-4421
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's laser exposure system consists of the laser unit that serves as the source of light and the laser scanning unit that uses a polygon mirror to control thebeam of laser light (for main scanning direction).1) The video signal from the controller block is converted into a laser drive signal by the video PCB, and is sent to the laser drive PCB. The laser drive signal is
used to turn on the laser unit for generation of a laser beam.2) The laser beam will assume a specific scanning direction upon hitting the polygon mirror rotating at a high speed.3) The surface of the photosensitive drum is charged to a positive potential. When the laser beam hits specific areas of the drum surface, a static image occursas a result.
In addition, the laser beam is also used for blank exposure applied to non-imaging areas.T-6-1
6.1.2 Major Components0015-4422
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's laser exposure system consists of the following major components:The machine uses a small-diameter 12-facet polygon mirror and a wide-area lens to enable scanning at high speed, at low power consumption, and at low operatingnoise. The laser unit is a double-beam unit.
F-6-1T-6-2
Item Description
Laser intensity control [1] laser power auto control (APC control)
[2] optimum intensity control to suit drum surface potential
Laser scanning method scanning by semi-conductor laser
synchronization control main scanning direction: control by BD signal
sub scanning direction: controlled by laser write start signal
Laser scanner motor control [1] constant speed rotation control
[2] full/standby speed switchover
Item Description
Laser semi-conductor visible laser light (about 660 nm), double beam
Laser scanner motor DC motor, 2-speed control (at full speed, about 41338 rpm)
Polygon mirror 12 facets
BD mirror/BD PCB laser beam detection
laser driver PCB Laser activation control
Video PCB laser scanner motor rotation control
Polygon mirrorLaser unit
BD mirror
Laser mirror 2
Laser mirror 3
Laser mirror 4
Laser mirror 1
Photosensitive drum
BD PCB
Chapter 6
6-2
6.2 Basic Sequence
6.2.1 Basic Sequence of Operation (laser exposure)0015-4424
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-6-2
6.3 Various Controls
6.3.1 Controlling the Laser Activation Timing
6.3.1.1 Generating the Sync Signal0015-4425
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The BD signal used to synchronize the video signal in laser scanning direction is generated by the BD PCB with reference to the laser beam reflected by the BDmirror mounted on the laser beam optical path. The CCD/AP PCB reads the image signal from the CCD, and sends it to the controller block. The controller block,in response, executes image processing, and sends the result as a video signal to the laser driver PCB by way of the video PCB and as the laser intensity controlsignal to the laser unit.
6.3.1.2 Flow of the Sync Signal0015-4426
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1] BD signal (upon detection of laser light, '0').[2] phase matching is executed with reference to the printer, and the synch signal is generated.[3] reads the image data from the image memory in keeping with the printer sync signal.[4] video signal[5] converts the 2-pixel parallel signal into a signal-pixel serial signal.[6] laser drive signal (drives the laser unit according to the video signal).
F-6-3
ERROR DODE:E100Issued when the BD signal is not detected within a specific period of time after the laser has been turned on.
6.3.2 Controlling the Intensity of Laser Light
6.3.2.1 Controlling the Laser Intensity0015-4427
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Main power switch ON Start key ON
Image leading edge signal(PTOP)
Laser
PRINTINTRWMUP CNTR WLSTR LSTR STBYSTBY
BD signal(BD)
Laser scanner motor(M15)* Full speedHalf speed Half speed
Video signal
BD PCB Video PCB
Laser driverPCB
DC controllerPCB
Controller
PHSYNC
VIDEO
J4500 J1411151413121110987654321
151413121110987654321
GND(N.C.)CSUDIRDIOSCLKGNDSDCLKGNDCTL2CTL1CTL0APC-SELGND+5V
Jxxxx Jxxxx123456789
1011121314
1234567891011121314
24VACCDECGNDFG5VBDGNDERMDIERMDOERMSKERMCSGND3.3V
JxxxxJ1401123456789101112131415161718192021222324252627282930
123456789
101112131415161718192021222324252627282930
???
Chapter 6
6-3
The laser driver circuit serves to drive the semi-conductor laser with reference to the laser drive signal (LD) coming from the DC controller PCB.
The laser drive circuit is associated with the following items of control:- laser activation control- laser intensity control (APC control)- laser intensity control to suit the drum surface potential
The various signals have the following meanings and functions:[1] sample laser activation signal; for each scan, it turns on the laser for sampling of light intensity (for imaging)
[2] laser activation enable signal; after the Start key has been pressed, it goes '0'when the laser is ready for activation.[3] laser write start signal; when paper reaches the laser write start sensor (PS28) mounted in front of the registration roller, the machine starts laser write oper-ation.[4] the machine monitors the intensity of laser light upon its activation (for sampling), and feeds the appropriate value to the laser drive circuit.[5] the machine controls the output so that the value that has been fed and the reference value from the DC controller are identical.[6] laser intensity reference signal; it serves as the laser activation reference (determined as a result of potential control by the DC controller).
F-6-4
MEMO:- The laser power is adjusted automatically when the laser unit is replaced.- When the manual feed tray is used as the source of paper, the write operation starts when the registration paper sensor (PS29) detects paper.
SERVICE MODE:DISPLAY> DPOT> LLMTindicates the laser power voltage control value for copier imaging.DISPLAY> DPOT> LPOWER-Pindicates the result of potential control for the laser intensity used during printer (PDL) imaging.DISPLAY> DPOT> LPOWER-Cindicates the result of potential control for the laser intensity used during copier imaging.DISPLAY> MISC> LPOWERindicates the laser intensity in real time.ADJUST> LASER> PVE-OFSTused to adjust the laser incident point.FUNCTION> LASER> POWERused to turn on laser light.
6.3.2.2 APC Control0015-4428
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine executes APC control so that the laser light will remain at a constant level by adjusting the output of the laser diode mounted on the laser driver.The control mechanism takes place on the DC control PCB.The DC controller sends the laser control signal (LD1: CTL0=0, CTL1=1, CTL2=0; LD2: CTL0=1, CTL1=0, CTL2=0; both APC-SEL=0) to the laser driver ICon the laser driver PCB.In response, the laser driver IC sets APC mode, and forces the laser diode (LD) to emit light.While all this is under way, the laser driver IC monitors the laser diode (LD) by means of a photo diode (PD), and adjusts the output of the laser diode unit so thatthe intensity is at a specific level.
DC controllerPCB
Laser driver PCBJ1408
J1411
J113
J122 J1401 J4500
LWRPD
J5501
Laser block
Laser
PhotoMonitor
Laser driver Circuit
B2
Laser writeStart sensor(PS28)
Laser unit
Video PCB
7654321
GNDGND
VD1NVD2PGND
VD2NVD2P
123456
12345678
GNDSDCLK
GNDSCLK
DIODIR
CSUGND
12345678
151413121110987654321
151413121110987654321
GND(N.C.)CSUDIRDIO
SCLKGND
SDCLKGNDCTL2
[2] CTL1[1] CTL0
APC-SELGND+5V
[6]
[4]
[5]
[1][2]
[3]
Chapter 6
6-4
F-6-5
6.3.3 Controlling the Laser Scanner Motor
6.3.3.1 Controlling the Laser Scanner Motor0015-4472
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine controls the laser scanner motor so that the motor always rotates at a specific speed.The control mechanism takes place in the motor speed control block.The motor speed control block detects the speed detection signal (FG, BD), and compares it against the reference signal generated by the reference signal generationblock on the DC controller PCB; it then controls the acceleration signal (ACC) and the deceleration signal (DEC) so that the motor will rotate at a specific speed.The machine switches over speed detection to suit the current printer state, thereby reducing the time used to control the scanner motor.The FG signal is a detection signal used for rough adjustment of the motor speed, while the BD signal is a detection point signal used to fine-tune the motor speed.
T-6-3
F-6-6
ERROR CODE:E110 (scanner motor error)-0001: after the scanner motor has been started up, the FG signal is not detected within a specific period of time, or while the scanner motor is rotating at a stable
speed, the FG signal is not detected.
Start-up startup -> half speed FG control
half speed -> full speed FG -> BD control
STBY half speed FG control
Imaging full speed BD control
Deceleration full speed -> half speed BD -> FG control
half speed -> stop FG control
LaserDriver
IC
5V
PD
LD
J101
APC-SEL
CTL0
CTL1
CTL2
APC-SEL
CTL0
CTL1
CTL2
J121
DC controllerPCB
Video PCB Laser Driver PCB
Laser ScannerMotor
DC controllerPCB
Video PCB
J126 J1403
J1410 J2511
FGACCDEC
M22Reference
signalgeneration
block
BD PCB
BD BD
J2701
Motor speedcontrolblock
Chapter 6
6-5
6.4 Parts Replacement Procedure
6.4.1 Laser Scanner Unit
6.4.1.1 Removing the Laser Scanner Unit0015-4863
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the right door unit (upper); then, remove the 1 screw [2] from thedoor strap, and fully open the right door unit (upper).
F-6-72) Slide the developing assembly locking unit [2] in the direction of the ar-
row to detach.- 1 Screw [1]
3) Detach the scanner cover [4].- 4 Screw [3]
F-6-84) Disconnect the 4 connectors [1].5) Detach the 1 leaf spring [3].
- 2 Screw [2]6) Hold the front of the laser scanner unit [4], and lift and take out.
F-6-9
6.4.1.2 When Replacing the Laser Scanner Unit0015-9960
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If the temperature of the fixing assembly is 150 deg C or higher when themain power switch is tuerned on, the machine will not execute potential con-trol. If such is the case after replacing the scanner unit, manually execute po-tential control in service mode as follows:1) Make the following selections in service mode: COPIER> FUNCTION>
DPC> DPC; then, enter '1', and press [OK].
2) Turn off and then back on the main power switch.
[1][2]
[1] [2]
[3] [3][4]
[1]
[2]
[3]
[4]
Chapter 7 Image Formation
Contents
Contents
7.1 Construction ...................................................................................................................................................................7-17.1.1 Overview...................................................................................................................................................................................... 7-17.1.2 Major Components....................................................................................................................................................................... 7-1
7.2 Image Formation Process...............................................................................................................................................7-17.2.1 Overview...................................................................................................................................................................................... 7-1
7.3 Basic Sequence ..............................................................................................................................................................7-27.3.1 At Power-On ................................................................................................................................................................................ 7-27.3.2 At Time of Printing ...................................................................................................................................................................... 7-3
7.4 Potential Control ............................................................................................................................................................7-37.4.1 Overview...................................................................................................................................................................................... 7-37.4.2 Copier/Printer Potential Control .................................................................................................................................................. 7-37.4.3 Determining the Primary Current ................................................................................................................................................ 7-67.4.4 Determining the Laser Output ..................................................................................................................................................... 7-67.4.5 Determining the Developing Bias................................................................................................................................................ 7-67.4.6 APC Correction............................................................................................................................................................................ 7-77.4.7 Adjusting the Density in Various Modes..................................................................................................................................... 7-7
7.5 Charging Mechanism .....................................................................................................................................................7-87.5.1 Controlling Pre-Exposure LED.................................................................................................................................................... 7-8
7.5.1.1 Pre-Exposure LED Control .............................................................................................................................................................................7-87.5.2 Primary Charging Mechanism ..................................................................................................................................................... 7-9
7.5.2.1 Overview .........................................................................................................................................................................................................7-97.5.2.2 Primary Charging Assembly Cleaning Mechanism........................................................................................................................................7-97.5.2.3 Others ............................................................................................................................................................................................................7-10
7.5.3 Dust-Collecting Roller Bias ....................................................................................................................................................... 7-107.5.3.1 Overview .......................................................................................................................................................................................................7-10
7.5.4 Pre-Transfer Charging Mechanism............................................................................................................................................ 7-117.5.4.1 Overview .......................................................................................................................................................................................................7-117.5.4.2 Controlling the Output to Suit the Environment (fuzzy control) ..................................................................................................................7-117.5.4.3 Pre-Transfer Charging Assembly Cleaning Mechanism...............................................................................................................................7-127.5.4.4 Others ............................................................................................................................................................................................................7-12
7.6 Drum Cleaner Unit.......................................................................................................................................................7-127.6.1 Overview.................................................................................................................................................................................... 7-127.6.2 Detecting the State (full) of the Collecting Toner Case............................................................................................................. 7-137.6.3 Drum/Separation Claw Bias Control ......................................................................................................................................... 7-14
7.7 Developing Assembly ..................................................................................................................................................7-147.7.1 Controlling the Developing Assembly Drive ............................................................................................................................ 7-147.7.2 Controlling the Developing Bias ............................................................................................................................................... 7-147.7.3 Detecting the Toner Level and Controlling Toner Supply ........................................................................................................ 7-15
7.8 Transfer Mechanism ....................................................................................................................................................7-167.8.1 Transfer Charging Mechanism .................................................................................................................................................. 7-16
7.8.1.1 Overview .......................................................................................................................................................................................................7-167.8.1.2 Controlling the Output to Suit the Environment (fuzzy control) ..................................................................................................................7-167.8.1.3 Transfer Charging Assembly Cleaning Mechanism .....................................................................................................................................7-177.8.1.4 Others ............................................................................................................................................................................................................7-17
7.9 Separation Mechanism.................................................................................................................................................7-187.9.1 Separation Charging Mechanism............................................................................................................................................... 7-18
7.9.1.1 Overview .......................................................................................................................................................................................................7-187.9.1.2 Correcting the Output to Suit the Environment and the Drum Surface Potential .........................................................................................7-187.9.1.3 Others ............................................................................................................................................................................................................7-19
7.10 Parts Replacement Procedure.....................................................................................................................................7-207.10.1 Process Unit ............................................................................................................................................................................. 7-20
Contents
7.10.1.1 Before Removing Process Unit................................................................................................................................................................... 7-207.10.1.2 Removing Process Unit ............................................................................................................................................................................. 7-207.10.1.3 Mounting Process Unit .............................................................................................................................................................................. 7-20
7.10.2 Pre-Exposure Lamp ................................................................................................................................................................. 7-217.10.2.1 Before Removing Pre-Exposure Lamp ...................................................................................................................................................... 7-217.10.2.2 Removing Pre-Exposure Lamp .................................................................................................................................................................. 7-217.10.2.3 Cleaning Primary Toner Blocking Sheet ................................................................................................................................................... 7-21
7.10.3 Primary Charging Assembly.................................................................................................................................................... 7-217.10.3.1 Before Removing Primary Charging Assembly ......................................................................................................................................... 7-217.10.3.2 Removing Primary Charging Assembly .................................................................................................................................................... 7-21
7.10.4 Pre-Transfer Charging Assembly ............................................................................................................................................ 7-227.10.4.1 Before Removing Pre-Transfer Charging Assembly ................................................................................................................................. 7-227.10.4.2 Removing Pre-Transfer Charging Assembly ............................................................................................................................................. 7-22
7.10.5 Photosensitive Drum................................................................................................................................................................ 7-227.10.5.1 Points to Note When Handling Photosensitive Drum ............................................................................................................................... 7-227.10.5.2 Before Removing Photosensitive Drum ..................................................................................................................................................... 7-227.10.5.3 Removing Photosensitive Drum ................................................................................................................................................................ 7-227.10.5.4 Cleaning Photosensitive Drum .................................................................................................................................................................. 7-23
7.10.6 Drum Motor ............................................................................................................................................................................. 7-237.10.6.1 Before Removing Drum Motor .................................................................................................................................................................. 7-237.10.6.2 Removing Drum Motor ............................................................................................................................................................................. 7-23
7.10.7 Photosensitive Drum Heater .................................................................................................................................................... 7-247.10.7.1 Points to Note When Handling Photosensitive Drum ............................................................................................................................... 7-247.10.7.2 Before Removing Photosensitive Drum Heater ......................................................................................................................................... 7-247.10.7.3 Removing Drum Heater ............................................................................................................................................................................. 7-247.10.7.4 Points to Note When Mounting Drum Heater ........................................................................................................................................... 7-24
7.10.8 Cleaning Blade......................................................................................................................................................................... 7-247.10.8.1 Configuration .............................................................................................................................................................................................. 7-247.10.8.2 Before Removing Cleaning Blade ............................................................................................................................................................. 7-247.10.8.3 Removing Cleaning Blade .......................................................................................................................................................................... 7-247.10.8.4 Mounting Cleaning Blade .......................................................................................................................................................................... 7-25
7.10.9 Side Seal................................................................................................................................................................................... 7-257.10.9.1 Before Removing Side Seal ....................................................................................................................................................................... 7-257.10.9.2 Removing Side Seal ................................................................................................................................................................................... 7-26
7.10.10 Cleaner Scraper...................................................................................................................................................................... 7-267.10.10.1 Before Cleaning Cleaner Scraper ............................................................................................................................................................ 7-267.10.10.2 Cleaning Cleaner Scraper ......................................................................................................................................................................... 7-26
7.10.11 Hopper Assembly................................................................................................................................................................... 7-267.10.11.1 Before Removing Hopper Assembly ....................................................................................................................................................... 7-267.10.11.2 Removing Hopper Assembly ................................................................................................................................................................... 7-26
7.10.12 Hopper Supply Motor ............................................................................................................................................................ 7-277.10.12.1 Before Removing Toner Supply Motor ................................................................................................................................................... 7-277.10.12.2 Removing Toner Supply Motor ............................................................................................................................................................... 7-27
7.10.13 Hopper Strring Motor ............................................................................................................................................................ 7-277.10.13.1 Before Removing Hopper Stirring Motor ................................................................................................................................................ 7-277.10.13.2 Removing Hopper Stirring Motor ............................................................................................................................................................ 7-27
7.10.14 Developing Assembly............................................................................................................................................................ 7-287.10.14.1 Removing Developing Assembly ............................................................................................................................................................ 7-287.10.14.2 Cleaning Developing Toner Blocking Sheet ........................................................................................................................................... 7-28
7.10.15 Developing Cylinder.............................................................................................................................................................. 7-297.10.15.1 Before Removing Developing Cylinder .................................................................................................................................................. 7-297.10.15.2 Removing Developing Cylinder .............................................................................................................................................................. 7-29
7.10.16 Developing Blade................................................................................................................................................................... 7-297.10.16.1 Before Removing Developing Blade ....................................................................................................................................................... 7-297.10.16.2 Removing Developing Blade ................................................................................................................................................................... 7-297.10.16.3 Mounting Developing Blade..................................................................................................................................................................... 7-29
7.10.17 Transfer/Separation Charging Assembly............................................................................................................................... 7-307.10.17.1 Removing Transfer/Separation Charging Assembly ............................................................................................................................... 7-307.10.17.2 Mounting Transfer/Separation Charging Assembly ................................................................................................................................ 7-30
7.10.18 Separation Claw/Separation Claw Drive Assembly .............................................................................................................. 7-30
Contents
7.10.18.1 Before Removing Separation Claw Holder ..............................................................................................................................................7-307.10.18.2 Removing Separation Claw Holder .........................................................................................................................................................7-30
7.10.19 Potential Sensor Unit ............................................................................................................................................................. 7-317.10.19.1 Outline.......................................................................................................................................................................................................7-317.10.19.2 Before Removing Potential Sensor Unit ..................................................................................................................................................7-317.10.19.3 Removing Potential Sensor Unit ..............................................................................................................................................................7-31
7.10.20 Charging Wire........................................................................................................................................................................ 7-317.10.20.1 Outline.......................................................................................................................................................................................................7-317.10.20.2 Routing Charging Wire ............................................................................................................................................................................7-317.10.20.3 Routing Grid for Primary Charging Assembly ........................................................................................................................................7-327.10.20.4 Adjusting Height of Charging Wire .........................................................................................................................................................7-32
Chapter 7
7-1
7.1 Construction
7.1.1 Overview0015-4473
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the functions of and the methods used by the machine's image formation system:T-7-1
7.1.2 Major Components0015-4474
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the major components of the machine's image formation system:
F-7-1
7.2 Image Formation Process
7.2.1 Overview0015-4475
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's image formation process consists of the following 8 steps:
Item DescriptionPhotosensitive drum amorphous silicon (80-mm dia. A-Si)
cleaning: by bladeDeveloping assembly developing cylinder (24.5-mm dia.)
developing method: dry, 1-component toner projection
toner: magnetic negative toner
Pre-exposure LED array
on/off control
Potential sensor potential control
[1] sets primary current[2] sets laser output[3] sets developing bias (DC)
wire auto cleaning [1] primary charging wire
[2] pre-transfer charging wire
[3] transfer charging wire
[4] separation charging wire
Primary charging control DC constant current control: set by result of potential control
Grid bias control fixed voltage control; fixed by varistor
Developing bias control AC constant voltage control: on/off control onlyDC constant voltage control: set by result of potential control
dust-collecting roller bias control DC non-control
pre-transfer charging control AC constant voltage control: fuzzy control by environment sensor
DC constant current control: on/off only
Transfer charging control DC constant current control: fuzzy control by environment sensor
Separation charging control AC constant voltage control
DC constant current control: fuzzy control based on output of environment sensor and drum surface potential
Developing assembly
Dust-colleting roller
Pre-transfer charging assembly
Transfer guide
Transfer charging assembly
Separation charging assembly
Cleaner unit
Pre-exposure
Primary charging assembly
Potential sensor
Chapter 7
7-2
T-7-2
*Toner is deposited. The machine also executes black exposure using its laser unit.
F-7-2
7.3 Basic Sequence
7.3.1 At Power-On0015-4476
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-7-3The sequence of operation is as follows:[1] The machine executes copier potential control.
[2] The machine executes printer potential control.
step 1 pre-exposure
step 2 primary charging (positive DC)
step 3 laser exposure*
step 4 development (AC + positive DC)
step 5 transfer (negative DC)
step 6 separation (AC + positive DC)
step 7 fixing
step 8 drum cleaning
8. Drum charging
1. Pre-exposure
2. Primary charging 3. Laser exposure
4. Development
5. Transfer
6. Separation7. FixingDelivery
Deck/cassette
Registration
Manual feed tray
flow of paper
direction of drum rotation
Static Image Formation Block
Main power switch ON
Control panel power switch ONStart key ON
INTRWMUPRWMUPSLEEP STBY
Fixing assembly temperature 195 C 200 C
Drum motor (M1)
Pre-exposure LED
Primary charging
Pre-transfer charging bias (AC)
Grid bias
Developing clutch (CL4)
Developing bias (AC)
Separation claw bias (AC)
Developing bias (DC)
Dust-collecting roller bias (DC)
Separation charging bias (DC)
Laser activation
Main motor (M2)
[1] [2]
Pre-transfer charging bias (DC)
Transfer charging
Separation charging bias (AC)
Chapter 7
7-3
7.3.2 At Time of Printing0015-4477
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-7-4The following shows the sequence of operation:[1] The machine executes a series of charging operations prior to an image formation session, thus stabilizing the potential of the drum.
[2] The machine executes image formation 1.[3] The machine executes image formation 2.
7.4 Potential Control
7.4.1 Overview0015-4479
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine uses the following functions and control mechanisms associated with its potential control system:1. copier/printer potential control
2. APC (auto power control) correction3. primary current determination (VD control)4. laser output determination (VL control)5. post-laser illumination potential measurement (VDC control)
The following shows the construction of the machine's control system associated with potential control:
F-7-5The following signals are associated with potential control:[1] POT-DT, drum surface potential measurement
[2] POT-ON, if '1', turns on the potential sensor
7.4.2 Copier/Printer Potential Control0015-4480
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Drum motor (M1)
Pre-exposure LED
Primary charging
Pre-transfer charging bias (AC)
Grid bias
Developing clutch (CL4)
Developing bias (AC)
Developing bias (DC)
Dust-collecting roller bias (DC)
Separation charging bias (DC)
Laser activation
Main motor (M2)
Pre-transfer charging bias (DC)
Transfer charging
Separation charging bias (AC)
Start key ON
PRINT LSTRSTBY STBYINRT
Separation claw bias (AC)
[2][1] [3]
Primary charging wire
Potential sensor
Laser light
Developing cylinder
DC co
ntro
ller P
CB
Lase
r driv
er P
CBD
evel
opin
g cy
linde
r
Pote
ntia
l con
trol P
CB
Control signal
Control signal
Det
ectio
n si
gnal
J103 J31234B1
B2B3B4
0V
24V
POT-DTPOT-ON
[1][2]
Developing bias (DC) determination
Laser output level determination
Primary current determination
Chapter 7
7-4
A. Timing and particulars of potential control1. At the time of warm-upThe machine's potential control consists of copier potential control mechanisms and printer potential control mechanisms.The machine uses VD=390V for both copier and printer control mechanisms.The timing of potential control is as follows:
T-7-3
2. In the service modeIf enabled in service mode, potential control starts 10 min and 60 min after the main power switch is turned on or when the door is opened and closed. The timingand particulars of potential control are as follows:
T-7-4
B. Sequence of potential control 1. At the time of warm-up
F-7-6The sequence and particulars of potential control are as follows:[1] copier potential control: VD = 8 times max.; VL1 = 8 times max.; VL2 = once
[2] printer potential control: VD = 8 times max.; VL1 = 8 times max.; VL2 = once
SERVICE MODE:
At time of warm-up
Purpose to execute potential control for copier/printer mode
to determine a constant value for copier/printer mode
Operating condition - the temperature of the fixing assembly is 50 deg C or lower when the main power switch is on- when the first image is being formed 60 min after warm-up
Operation length 10 sec (approx.)
Service mode may be enabled or disabled using the following: COPIER>OPTION>BODY>PO-CNT
Default ON (potential control for both copier and printer modes)
10 min and 60 min after the main power switch is turned on
Purpose to control sensitivity, thus making up for changes in drum temperatureto accommodate changes in charging efficiency
Operating conditions - start of the 1st job 10 min and 60 min after the main power switch has been turned on- the door is opened and closed
Operation length off: is not executed (default)
short mode: about 5 sec
standard mode: about 10 sec
service mode settings may be OFF, short, or standard as determined by the following: COPIER>OPTION>BODY>PO-CNTMD
Default OFF
WMUPRWMUP STBY
Fixing assembly temperature 195 C 200 C
Drum motor (M1)
Primary charging
Laser
Potential sensor
Printer potential control [2]Copier potential control [1]
VD VD VD VL1 VL2VL1 VD VD VD VL1 VL2VL1
Chapter 7
7-5
COPIER>OPTION>BODY>PO-CNT (enable/disable potential control)0: disable potential control1: enable potential control
2. In the service modeThe following settings may be made for potential control executed 10 min and 60 min after the main power switch is turned on and when the door is opened andclosed: COPIER>OPTION>BODY>PO-CNTMD:[1] off (default): disable potential control
[2] short mode: decrease the length based on potential attained by executing either of the 2 modes[3] standard mode: execute both copier and printer potential control in succession
a. Short ModeThe machine executes one of the 2 potential modes, and makes an assumption for the other mode.For warm-up after power-on, the machine refers to the primary current level, laser output level, and developing bias DC level for both copier potential control andprinter potential control, thereby computing and saving the resulting rate.In the course of potential control after power-on, the machine executes one of the 2 potential control modes, thus computing the other in relation to the rate it ob-tained at time of power-on and after power-on.The following is the sequence of operation used for short mode:
F-7-7
b. Standard ModeThe machine executes both copier potential control and printer potential control in succession.
F-7-8In addition to standard mode and short mode, the machine also offers 30-sec mode executed for 30-sec start-up.
c. 30-sec ModeThe machine executes 30-sec mode in a power save state and when it is turned on for the first time for the day.The machine uses the value of the previous control session to initiate laser exposure, measuring the post-laser illumination potential (VLM) and determining thedeveloping bias DC (Vdc).
SERVICE MODE:COPIER> OPTION> BODY> PO-CNT (turning off the potential control mechanism)0: disable potential control1: enable potential control (default)COPIER> OPTION> BODY> PO-CNTMD (selecting potential control mode)0: 10 min, 60 min potential control OFF (default)1: 10 min, 60 min short mode2: 10 min, 60 min normal modeCOPIER> OPTION> TEMPO> F-POT-SWEnter '1' if a transfer separation fault occurs because of a fault in the potential sensor (as a tentative remedy until the replacement of the sensor).COPIER> OPTION> TEMPO> F-POT-DEnabled when '1' is set for the following: COPIER>OPTION>TEMPO>F-POT-SW.0: if user primarily uses originals with low image ratio (text original; default)1: if user primarily uses originals with high image ratio (photo original)2: if re-transfer (drop-out at 50 mm of leading edge) occursCOPIER> OPTION> TEMPO> F-HUM-SWEnter '1' if the environment sensor is faulty (as a tentative remedy until replacement of the sensor).COPIER> OPTION> TEMPO> F-HUM-DEnabled if '1' is set for the following: COPIER>OPTION>TEMPO-F-HUM-SW.Enter the humidity reading of the site of installation (between 30% and 99%; default being 35%).COPIER> FUNCTION> DPC> DPC (forcing potential control)ON: execute potential controlCOPIER> ADJUST> V-CONT> EPOTOFST (setting potential sensor offset value)COPIER> ADJUST> V-CONT> DE-OFST (adjusting copy Vdc)COPIER> ADJUST> V-CONT> VD-OFST (setting copy VD target potential offset value)COPIER> ADJUST> V-CONT> DE-OFS-P (adjusting printer Vdc)COPIER> ADJUST> V-CONT> VD-OFS-P (setting printer VD target potential offset value)Enter the value indicated on the service label if you have initialized the RAM on the DC controller PCB.
Sets a constant level for both copier and printer potential control
Copier potential control
Printer potential control
Fixing assembly temperature(fixing assembly warm-up complete)
Control panel power switch ON
Start key ONPotential control Potential control
Start key ON
10 min later to less than 60 min 60 min later
Assumes a potential level for the other based on the result of copier or printer potential control
Assumes a potential level for the other based on the result of copier or printer potential control
Copier potential control
Printer potential control
Fixing assembly temperature(fixing assembly warm-up complete)
Control panel power switch ON
Start key ON Potential control Potential control
Start key ON
10 min later to less than 60 min 60 min later
Copier potential control and printer potential control during 1st job
Copier potential control and printer potential control during 1st job
Chapter 7
7-6
COPIER> FUNCTION> DPC>OFST (adjusting potential sensor offset)For the method of adjustment, see "Standards and Adjustments."
7.4.3 Determining the Primary Current0015-4481
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To measure the dark area potential (VD) for the first time after the power switch is turned on, the machine uses the most recently measured current level, and meas-ures the drum surface potential using the potential sensor. The DC controller PCB compares the drum surface potential and the target potential; as a result, if themeasured potential is +/-6 V of the target value, the machine corrects the primary current and measures the potential once again. The machine executes potentialmeasurement a maximum of 8 times, and also corrects the primary current as many times.
F-7-9
7.4.4 Determining the Laser Output0015-4482
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To measure the light area potential (VL1) for the first time after the power switch is turned on, the machine uses the most recent laser output level (LP0), and meas-ures the drum surface potential using the potential sensor. The DC controller PCB compares the drum source potential and the target potential; if the measuredpotential is +/-10V of the target value, the machine corrects the potential of the laser output, and measures the potential once again. The machine executes potentialmeasurement a maximum of 8 times, and also corrects the lower output level as many times. In addition, the machine measures the light area (VL2) for the devel-oping bias for use in determining the laser output (LP) needed to attain the target potential.
F-7-10
7.4.5 Determining the Developing Bias0015-4483
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine determines the developing bias (VDC) as follows with reference to the drum surface potential (VL2):VDC = VL2 + delta VDCFor copier potential, delta VDC=110 VFor printer potential, delta VDC=85 to 110 V (i.e., the printer potential varies to suit the reading of the environment sensor, thus ensuring the reproduction of correctline width)
WMUPRWMUP STBY
200 C
Potential sensor
Primary charging
Grid bias
Vpc Vpc Vpc Vpc
VD
+6V-6V
VD
VD
Correction control sequence start
Potential control sequence start
Previous potential
VDVD VD VD VD VD
Target VD
Fixing assembly temperature 195 C
WMUPRWMUP STBY
200˚C
Potential sensor
Developing bias(DC)Laser
LP0 LP0 LP0 LP0 LP0 LP
VL1 VL1 VL1 Target VL1VL1VL1
Correction controlsequence start
Fixing assemblytemperature 195 Deg C
VL1
+6V-6V
VL1
VL1
VL1Previous potential
Target VL1
Potential controlsequence start
VL2
Chapter 7
7-7
F-7-11
7.4.6 APC Correction0015-4484
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Changes in the laser output cause changes in the surface potential. To maintain a specific level of surface potential, the machine corrects the laser output controlvalue. The following shows the type and the particulars of laser output control value correction:
F-7-12
(1) Between-Sheet APC ControlPurpose: to maintain a specific level of surface potential without lowering the productivity during a continuous job; the machine measures the potential afterlaser output between sheets, and corrects the laser output control value.Timing: over the 1st interval between sheets every 1 min after the start of a continuous print job.Potential measurement: the drum potential varies in drum peripheral direction; thus, the machine computes the average drum surface potential in drumperipheral direction. It uses the result of computation to determine the laser output correction value. If measurement is not possible because of conditionsimposed by the need for measurement between sheets, the machine will continue measurement for an additional 1 min.
(2) Initial Rotation APC ControlPurpose: to make up for the changes in the VL potential of the laser output occurring after an appreciable time, the machine measures the drum potential andcorrects the laser output control value.Timing: during initial rotation of the 1st job 60 min after the end of a job.Potential measurement: the drum potential varies in peripheral direction, and the machine computes the average drum potential in peripheral direction. Themachine uses the result of computation to obtain the appropriate laser output correction value.
(3) Last Rotation APC ControlPurpose: when intermittent printing is repeated at short intervals, the absence of potential control can cause changes in the VL potential of the laser output.To make up for the changes, the machine computes a correction value for the laser output control value and uses the result for the next job.Timing: during last rotation for the 1st job 30 min after the most recent laser output correction.Potential measurement: the drum potential varies in peripheral direction. The machine computes the average drum potential in peripheral direction, andobtains the appropriate laser output correction value using the result of computation.
SERVICE MODE:COPIER>OPTION>BODY>LAPS-SW (switching laser correction)0: ON (left alone for 10 min -> initial rotation APC)1: ON (left alone for 60 min -> initial rotation APC; default)2: ON (left alone for 120 min -> initial rotation APC)3: OFF only for initial rotation APC4: OFF
7.4.7 Adjusting the Density in Various Modes0015-4486
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine corrects the development bias determined as a result of potential control for the following operating modes, and uses the result as the target value forthe individual modes:
WMUPRWMUP STBY
200 C
Potential sensor
Resulting potential
Laser
Secondary charging
VpcVpc LP0
Vpc
Potential control sequence start
VD VL1 VL2
Vdc
VDVdc
Photosensitive drum
Developing cylinder
Potential sensor
Laser output determined
Fixing assembly temperature 195 C
LP
Primary charging current determined
Copier potential control
Printer potential control
Main power switch ON
Fixing assembly temperature 195- C(fixing assembly warm-up complete)
Control panel power switch ON
Start key ON
laser output value correction
1 min later 1 min later
Continuous printing
Laser output value correction
Chapter 7
7-8
1. Adjusting the Density for CopyingThe machine increases the developing bias to decrease the copy density. If increased in excess, the bias can cause light images; if decreased in excess, on the otherhand, the background can developing fogging. In light of this, the machine executes density processing using changes in the developing bias and image processing(binary density processing).Purpose: to obtain the density suited to the user's needs.Method of correction: uses the developing bias and image processing (binary density processing) according to the F-value setting.
T-7-5
2. Adjusting the Density for PrintingThe machine increases the developing bias to increase the print density. If increased in excess, the background can develop fogging. At the lower limit of the de-veloping bias, the machine uses the changes in the developing bias and image processing (thickening processing) to ensure appropriate density.Purpose: to obtain the density suited to the user's needs.Method of correction: uses the developing bias and image processing (thickening) to suit the F-value setting.
T-7-6
*1: Thickening processing may be enabled for all F values in user mode ('correct fine line').
7.5 Charging Mechanism
7.5.1 Controlling Pre-Exposure LED
7.5.1.1 Pre-Exposure LED Control0015-4487
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine is equipped with a pre-exposure LED used to prevent adhesion of excess toner on the photosensitive drum because of residual charges. The followingis an item associated with the pre-exposure LED control system:
1. turning on/off the pre-exposure LED
F value Developing DC bias standard value (V)
Shift (V) Image processing Image density
1 240 60 yes lighter
2 220 40 no
3 180 0 no
4 140 -40 no
5 120 -60 yes darker
F value Developing DC bias standard value (V)
Shift (V) Thickening*1 Image density
1 218 48 no light
2 205 35 no
3 194 24 no
4 182 12 no
5 170 0 no
6 153 -17 no
7 137 -33 no
8 120 -50 no
9 120 -50 yes dark
Chapter 7
7-9
F-7-13The following is the signal associated with the mechanism:[1] Pre-exposure LED control signal; when '0', LED goes on
7.5.2 Primary Charging Mechanism
7.5.2.1 Overview0015-4488
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following items are associated with the primary charging control system:1. turning on/off the primary corona current
2. controlling the constant current level of the primary corona current3. controlling the constant voltage level of the grid bias (fixed to 850 V by a valista)
The following shows the construction of the control system associated with the primary charging control system:
F-7-14The following signals are associated with the mechanism:[1] Primary charging leakage detection signal; when '0', if the current is too high or too low
[2] Primary corona current control signal; used to control the primary charging current generated by the high-voltage PCB[3] High-voltage remote signal; turning on/off the primary charging corona current output
7.5.2.2 Primary Charging Assembly Cleaning Mechanism0015-4489
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The primary charging wire cleaning mechanism is turned on at the following timing, and the construction of the control system is as shown:Timing of Cleaning
- when the wire cleaning mechanism is executed in user mode- when the wire cleaning mechanism is executed in service mode:
COPIER>FUNCTION>CLEANING>WIRE-CLN*1- after the end of cleaning, at the end of every 2,000 prints*2- in a low temperature or high humidity environment, if the fixing roller is 160 deg C or less when the power is turned on*1: The machine executes it when the primary charging wire or the transfer charging wire has been replaced.
*2: The default cleaning interval may be changed in service mode (COPIER> OPTION> BODY> W-CLN-P).
DC
-CO
N
Pre-exposure lamp24V
PRE_LED_ON* [1]
J103
A
DC
con
trolle
r PC
B
Hig
h-vo
ltage
PC
B
PRIMARY-LEAK-DETECT [1]
HVT-REMOTE [3]
Primary charging wireGrid wire
HVT-PRIMARY [2]
J102
A
J450
2
Chapter 7
7-10
F-7-15The following signals are associated with the mechanism:[1] Primary charging wire cleaning motor reverse direction signal; when '1', the wire cleaner moves toward the rear.
[2] Primary changing wire cleaning motor normal direction signal; when '1', the wire cleaner moves toward the front.[1] 1éüë—ìdê¸ê¥ë|ÉÇÅ[É^ãtì]ãÏìÆêMçÜ1: "1" ÇÝÉèÉCÉÑÉNÉäÅ[ÉiÇÕâúï°å¸Ç…à⁄ìÆ[2] 1éüë—ìdê¸ê¥ë|ÉÇÅ[É^êŠì]ãÏìÆêMçÜ2: "1" ÇÝÉèÉCÉÑÉNÉäÅ[ÉiÇÕéËëOï°å¸Ç…à⁄ìÆ
7.5.2.3 Others0015-4490
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
SERVICE MODE:COPIER>FUNCTION>CLEANING>WIRE-CLNUse it so that the machine causes the wire cleaner to make 5 round trips to automatically clean the charging wire when the primary charging wire or the transferwire has been replaced.COPIER>OPTION>BODY>W-CLN-PUse it to specify the interval at which the primary charging wire is automatically cleaned in terms of the number of prints made.
7.5.3 Dust-Collecting Roller Bias
7.5.3.1 Overview0015-4491
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine is equipped with a dust-colleting roller to collect stray toner occurring after development. The toner collected on its surface is removed by the workof a scraper.
The following item is associated with the dust-collecting roller bias control system:1. turning on/off the dust-collecting roller bias
The following shows the construction of the dust-collecting roller bias:
Primary changing assembly
WireD
C c
ontr
olle
r P
CB
(to rear)
(to front)
PRIMARY_CLEAN_OUT1 [1]
J103
A
Wire cleaner
PRIMARY_CLEAN_OUT2 [2]
Primary charging wire cleaning motor(M6)
Chapter 7
7-11
F-7-16The following signal is associated with the mechanism:[1] dust-collecting roller bias remote signal; if '1', the dust-collecting roller bias turns on.
7.5.4 Pre-Transfer Charging Mechanism
7.5.4.1 Overview0015-4492
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following items are associated with the pre-transfer charging control system:1. controlling the constant current level of the DC bias
2. controlling the fixed voltage level of the AC bias3. controlling the output to suit the environment (fuzzy control)
The following shows the construction of the system associated with the pre-transfer charging control mechanisms:
F-7-17The following signals are associated with the mechanism:[1] Pre-transfer/separation charging leakage detection signal; when the current is too high or too low, '0'.
[2] Pre-transfer charging control signal; controls the DC bias current and AC bias voltage generated by the high-voltage PCB.[3] Pre-transfer/separation charging remote signal; turns on/off the pre-transfer/separation current output.
7.5.4.2 Controlling the Output to Suit the Environment (fuzzy control)0015-4494
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The pre-transfer charging current is optimized to suit the environment (i.e., reading of the environment sensor):
F-7-18
SERVICE MODE:
DC
co
ntr
olle
r P
CB
Hig
h-v
olt
age
PC
B
DC -1000V
HVT_ROLLER_BIAS [1] Dust-collecting
roller
ScraperJ1
02A
J450
2
DC
con
trol
ler
PC
B
HVT_POST [3]
SEPARATE-LEAK-DETECT [1]
Hig
h-vo
ltage
PC
B
Pre-transfer charging wire
HVT_AC [2]
Hig
h-vo
ltage
A
C tr
ansf
orm
er
AC+DC
J102
A
J450
2
J450
3
Low temperature High temperature
Pre
-tra
nsfe
r cu
rren
t
Chapter 7
7-12
COPIER>OPTION>BODY>FUZZY (turning on/off fuzzy control)0: enable fuzzy control (default)
1: low humidity mode (for pre-transfer charging current level lower than standard)2: normal humidity mode3: high humidity mode (for pre-transfer charging current higher than standard)
When set to '1' through '3', the machine executes the appropriate modes independently of the reading of the environment sensor.
7.5.4.3 Pre-Transfer Charging Assembly Cleaning Mechanism0015-4495
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine executes pre-transfer charging wire cleaning as follows using its associated mechanism:
Timing1. when wire cleaning is executed in user mode.
2. when wire cleaning is executed in service mode (COPIER> FUNCTION> CLEANING> WIRE-CLN)*1.3. after the end of cleaning, every 2,000 prints*2.4. in a low temperature or high humidity environment, if the fixing roller is 160 deg C or less when the power is turned on.
*1: The machine executes cleaning when the primary charging wire or the transfer charging wire has been replaced.*2: The default cleaning interval may be changed in service mode: COPIER> OPTION> BODY> W-CLN-P.
F-7-19The following signals are associated with the mechanism:[1] Pre-transfer charging wire cleaning motor normal direction signal; when '1', the wire cleaner moves toward the rear.
[2] Pre-transfer charging wire cleaning motor reverse direction signal, when '1', the wire cleaner moves toward the front.
7.5.4.4 Others0015-4496
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
SERVICE MODE:COPIER>ADJUST>HV-TR>PRE-TR (entering output adjustment value for pre-transfer charging current)Enter the value indicated on the service label if you have initialized the RAM on the DC controller PCB.COPIER>ADJUST>HV-TR>H-PRE-TR (entering offset value for pre-transfer high-voltage output of high-voltage unit)Enter the value indicated on the label attached to the new high-voltage unit if you have replaced the high-voltage unit or initialized the RAM on the DC controllerPCB.COPIER>ADJUST>HV-TR>D-PRE-TR (entering offset value for pre-transfer high-voltage output of DC controller PCB)Enter the value indicated on the label attached to the new DC controller PCB if you have replaced the DC controller PCB or initialized the RAM on the DC controllerPCB.COPIER>OPTION>BODY>W-CLN-PUse it to set the interval of automatic cleaning of the pre-transfer charging wire in terms of the number of prints.
7.6 Drum Cleaner Unit
7.6.1 Overview0015-4497
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the components found in the drum cleaner unit:
Wire cleaner
Wire
Pre-transfer charging assembly
Pre-transfer charging wire cleaning motor (M7)
(toward rear)(toward front)
POST_CLEAN_OUT2 [2]POST_CLEAN_OUT1 [1]
DC
con
trol
ler
PC
B
J103
A
Chapter 7
7-13
F-7-20
7.6.2 Detecting the State (full) of the Collecting Toner Case0015-4498
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the control mechanism used to see if the collecting toner case has become full:
F-7-21
ERROR CODE:E013-0001Indicated if the collecting toner feedscrew sensor (MSW2) has remained on for 5 sec or more.E821-0001The reading of the drum cleaner thermistor is 55 deg C at least once, causing the machine to assume that the inside of the cleaner is clogged with toner.
SERVICE MODE:COPIER>COUNTER>MISC>WASTE-TNRcollecting toner counter; when its reading reaches '250,000', the machine will issue an alarm on the User screen.Dispose of the collecting toner, and reset the error code.
MEMO:The collecting toner bottle can hold toner good for a maximum of 500,000 prints. The machine will indicate a collecting toner bottle full alarm when the counter
Pre-exposure lamp (LED)
Cleaning blade
Separation claw
Magnet roller
Auxiliary roller
Collecting toner feedscrew
Drum cleaner thermistor
DC
con
trol
ler
PC
B
Collecting toner feedscrew lock detection (SW5)
Collecting toner bottle
(front)
DRUM_M_ONDRUM_M_FG
0V
WASTE_TONER_FULL_SW
5V0V M1J1
08A
J107
B
to SW5
Drum cleaner thermistor
J103
A to Drum cleaner thermistor
Chapter 7
7-14
reading reaches '250,000'.
7.6.3 Drum/Separation Claw Bias Control0015-9606
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Since the separation claw contacts the drum, toner caught by the separation claw can fall in the feeder path as the machine is getting aged.Such events can cause the soiled back or faulty images.As a countermeasure, the machine supplies the AC bias voltage (Vpp430V) to the separation claw, which generates vibration to prevent the toner from accumulatingin the separation claw.
F-7-22
7.7 Developing Assembly
7.7.1 Controlling the Developing Assembly Drive0015-4499
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the construction of the developing assembly drive control system:
F-7-23The following signal is associated with the developing assembly control mechanism:
[1] Developing clutch drive signal; when '0', the drive of the main motor (M1) is transmitted to the developing assembly.
7.7.2 Controlling the Developing Bias0015-4500
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following items are associated with the developing bias control system:[1] Controlling the DC bias constant voltage
[2] Controlling the AC bias constant voltage
DC-CON HVTSeparationClaw AC
Bias PCB
SeparationClaw
CL1
Developing clutch
M1
DC
con
trol
ler
PC
B
DRUM_M_ON
0V
DRUM_M_FG
5V
DEV_CL_ON* [1]
24V
J108
BJ1
08A
Chapter 7
7-15
F-7-24The following signals are used in association with the developing bias control mechanism:[1] Developing DC bias current control signal; controls the DC component of the developing bias generated by the high-voltage power supply PCB.
[2] turns on/off the developing bias current output.
SERVICE MODE:COPIER>ADJUST>DEVELOP>BIAS(entering developing bias)Enter the value indicated on the service label if you have initialized the DC controller PCB.setting range: 0 (darker) to 600 (lighter)COPIER> ADJUST> DEVELOP> HVT-DE(entering offset value for developing high-voltage output of high-voltage unit)Enter the value indicated on the label attached to the new high-voltage unit if you have replaced the DC controller PCB or initialized the RAM on the DC controllerPCB.setting range: -100 (lighter) to +100 (darker)COPIER> ADJUST> DEVELOP> D-HV-DE(entering offset value for developing high-voltage output of DC controller PCB)Enter the value indicated on the label attached to the DC controller PCB if you have replaced the DC controller PCB or initialized the RAM on the DC controllerPCB.setting range: -100 (lighter) to +100 (darker)COPIER> ADJUST> V-CONT> DE-OFST)(adjusting VDC for copier)COPIER> ADJUST> V-CONT> DE-OFS-P)(adjusting VDC for printer)Enter the value indicated on the service label if you have initialized the RAM on the DC control PCB.
7.7.3 Detecting the Toner Level and Controlling Toner Supply0015-4501
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the components associated with the toner supply control system:
F-7-25[1] Toner bottle[2] Hopper assembly[3] Toner stirring plate[4] Toner feedscrew[5] Toner feed pipe[6] Developing assemblyM9: Hopper stirring motorM10: Toner supply motorTS1: Developing assembly toner level sensorTS2: Inside hopper toner level sensorDC-CON: DC controller (components used to detect level of remaining toner)
DC
con
trol
ler
PC
B
HVT_DEV_BIAS_DC [2]
HVT_DEV_BIAS_DC [1]
Developing cylinder
AC output 1200Vpp
Hig
h-vo
ltage
PC
B
J102
A
J450
2
M10
M9
DC-CON
J103B
HO
P_T
ON
ER
_SE
NS
OR
[2]
J103
ADEV_TONER_SENSOR[4]
HO
P_B
OT
TLE
_ON
[3]
HOP_BOTTLE_ON[1]
TS2
[1]
[2]
[3]
[4]
[6]
TS1
Chapter 7
7-16
Toner Supply SequenceThe toner inside the developing assembly is monitored by the developing assembly toner level sensor (TS1); when the toner inside the developing assembly fallsbelow a specific level, the developing assembly toner level signal goes '0' so that the DC controller PCB recognizes it.If the DC controller PCB detects the developing assembly toner level signal for 0.3 sec or more, it generates the hopper motor drive signal so that the hopper as-sembly will start supplying toner.When the toner inside the developing assembly reaches a specific level and, as a result, the developing assembly toner level signal remains '1' for 0.7 sec or more,the hopper supply motor stops.When the toner inside the hopper drops below a specific level, the hopper toner level detection signal goes '0'. If the signal remains '0' when the toner supply motorhas been turned on and off 20 times after the detection of the signal state by the DC controller, the machine issues a message of bottle exchange.Total rotating time reaches 60 seconds after the toner sensor in the developing assembly senses no toner, the machine issues a method of exchanging bottles andstops the ongoing printing operation.When the toner bottle is replaced, the hopper supply motor and the stirring motor are turned on, and the developing assembly inside toner level detection signalgoes '1', the machine resets the message of bottle exchange and resumes printing.
F-7-26
ERROR CODE:E020-0000Indicated while the output of the inside hopper toner level sensor (TS2) points to the presence of toner and the output of the developing assembly toner level sensor(TS1) inside the developing assembly points to the absence of toner for 120 sec or more.
7.8 Transfer Mechanism
7.8.1 Transfer Charging Mechanism
7.8.1.1 Overview0015-4502
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following items are associated with the transfer charging control system:1. controlling the DC bias constant current
2. controlling the output to suit the environment (fuzzy control)The following shows the construction of the transfer charging control system:
F-7-27The following signals are associated with the transfer charging control mechanism:[1] Transfer charging leakage detection signal; when the current is too high or too low, '0'
[2] Transfer charging current control signal; used to control the transfer current generated by the high-voltage PCB[3] High-voltage remote signal; turns on/off the transfer current output
7.8.1.2 Controlling the Output to Suit the Environment (fuzzy control)0015-4503
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The transfer charging current is optimized to suit the environment (i.e., reading of the environment sensor).
Toner supply sequence start
Toner supply
Hopper supply motor (M10)
Developing assembly toner level sensor (TS1)
Inside hopper toner level sensor (TS2)
Supply Supply
If 120 sec or more, '020-0000' is indicated
total activation (ON) time of hopper stirring motor reaching 60 sec, message of method of exchanging bottles -> print suspension.
1 cycle (5 sec max.)
toner supply motor driven for 20 cycles, message of exchanging bottles.
DC
con
trol
ler
PC
B
Hig
h-vo
ltage
PC
B
HVT_TRANSFER [2]
TRANSFER-LEAK-DETECT [1]
Transfer charging wireHVT-REMOTE [3]
J450
2
J102
A
Chapter 7
7-17
F-7-28
SERVICE MODE:COPIER>OPTION>BODY>FUZZY (turning on/off fuzzy control)0: turns off fuzzy control (default)
1: low humidity mode (for lower transfer charging current than standard)2: normal humidity mode3: high humidity mode (for higher transfer charging current than normal)
When set to '1' through '3', the machine executes the appropriate modes independently of the reading of the environment sensor.
7.8.1.3 Transfer Charging Assembly Cleaning Mechanism0015-4505
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the timing at which transfer charging wire cleaning is executed and the construction of the associated system:
Timing1. when wire cleaning is executed in user mode
2. when wire cleaning is executed in service mode (COPIER> FUNCTION> CLEANING> WIRE-CLN)*13. at the end of every 2,000 prints after the end of cleaning*24. if the fixing roller is 160 deg C or less in a low temperature or high humidity environment
*1: The machine executes wire cleaning when the primary charging wire or the transfer charging wire has been replaced.*2: The default cleaning interval may be adjusted in service mode: COPIER> OPTION> BODY> W-CLN-P.
F-7-29The following signals are used in association with the cleaning mechanism:[1] Transfer charging wire cleaning motor normal direction signal; when '1', the wire cleaner moves toward the rear.
[2] Transfer charging wire cleaning motor reverse direction signal; when '1', the wire cleaner moves toward the front.
7.8.1.4 Others0015-4509
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
SERVICE MODE:COPIER> ADJUST> HV-TR> TR-N1(adjusting the transfer charging current output for the 1st side of a duplex print or for a simplex print using plain paper)COPIER> ADJUST> HV-TR> TR-N2(adjusting the transfer charging current output for the 2nd side of a duplex print using plain paper)COPIER> ADJUST> HV-TR> HVT-TR(entering the offset value of the transfer high-voltage output of the high-voltage unit)Enter the value indicated on the label attached to the new high-voltage unit if you have replaced the high-voltage unit or initialized the RAM on the DC controllerPCB.COPIER> ADJUST> HV-TR> D-HV-TR(entering the offset value for the transfer high-voltage output of the DC controller PCB)Enter the value indicated on the label attached to the new DC controller PCB if you have replaced the DC controller PCB or initialized the RAM on the DC controllerPCB.COPIER> FUNCTION> CLEANING> WIRE-CLNUse it so that the machine automatically causes its wire cleaner to make 5 round trips if you have replaced the primary charging wire or the transfer charging wire.COPIER> OPTION> BODY> W-CLN-PUse it to set the interval of automatically cleaning the pre-transfer charging wire in terms of the number of prints.COPIER> OPTION> BODY> TR-SP-C1(switching over the transfer/separation output value for pickup from the right deck)
Tran
sfer
cur
rent
Low temperature High temperature
DC
con
trol
ler
PC
B
T/S_CLEANER_1 [1]
J106
A
Transfer/separation charging wire cleaning motor (M8)(toward the rear)
(toward the front)
Separation charging assembly
Transfer charging assembly
Wire
Wire cleaner
T/S_CLEANER_2 [2]
Chapter 7
7-18
COPIER> OPTION> BODY> TR-SP-C2(switching over the transfer/separation output value for pickup from the left deck)COPIER> OPTION> BODY> TR-SP-C3(switching over the transfer/separation output value for pickup from the cassette 4)COPIER> OPTION> BODY> TR-SP-C4(switching over the transfer/separation output for pickup from the manual feed tray)COPIER> OPTION> BODY> TR-SP-MF(Use it to switch the transfer/separation output for pickup from the manual feed tray.)COPIER> OPTION> BODY> TR-SP-DK(switching over the transfer/separation output value for pickup from the side paper deck)As necessary, switch over the transfer/separation output value for pickup from various sources of paper by way of correcting various faults:0: normal (default)
1: prevent re-transfer2: prevent separation fault3: prevent transfer fault
7.9 Separation Mechanism
7.9.1 Separation Charging Mechanism
7.9.1.1 Overview0015-4512
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following items are associated with the separation charging control system:1. controlling the constant current of the DC bias
2. controlling the constant voltage of the AC bias3. correcting the output to suit the environment and drum surface potential (fuzzy control)
The following shows the construction of the separation charging control system:
F-7-30The following signals are associated with the separation charging control mechanisms:[1] Separation charging leakage detection signal; if the current is too high or too low, '0'.
[2] Separation charging current control signal; used to control the DC bias current and the AC bias voltage generated by the high-voltage PCB.[3] Separation charging remote signal; turns on/off the separation current output.
7.9.1.2 Correcting the Output to Suit the Environment and the Drum Surface Potential0015-4514
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The separation current output is optimized to suit the environment (i.e., reading of the environment sensor) and the deposit of toner (either of 3 levels; low, average,high, as determined by the count of black pixels).
F-7-31[1] In a low humidity environment, paper tends to become dry, thus tending to collect charges (high resistance). The output is decreased.
[2] If the drum surface potential is low, the output is increased to prevent separation faults.[3] If the drum surface potential is high, the current level is lowered to prevent re-transfer.
DC
con
trol
ler
PC
B
AC+DC
HVT-AC [2]
SEPARATE-LEAK-DETECT [1]
HVT_SEPARATE [3]
Hig
h-vo
ltage
PC
B
Hig
h-vo
ltage
A
C tr
ansf
orm
erSeparation charging wire
J450
3
J450
2
J102
A
Sep
arat
ion
curr
ent(
A)
Toner deposit highToner deposit averageToner deposit low
If the toner deposit is high, the current level is lowered to prevent re-transfer.
If the toner deposit is low, the output is increased to prevent separation faults.
In a low humidity environment, paper tends to become dry, thus easily collecting charges (high resistance); to remedy the fact, the output is lowered.
Low humidity High humidity
Chapter 7
7-19
SERVICE MODE:COPIER> OPTION> BODY> FUZZY (turning off/on fuzzy control)0: enable fuzzy control (default)
1: low humidity mode (for higher pre-transfer charging current than normal)2: normal humidity mode3: high humidity mode (for higher pre-transfer charging current than normal)
If '1' through '3' is set, the machine executes the individual modes independently of the reading of the environment sensor.
7.9.1.3 Others0015-4515
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Service Mode:COPIER> ADJUST> HV-SP> SP-N1(adjusting the output of the 1st side of a duplex print or for a simplex print using plain paper)COPIER> ADJUST> HV-SP> SP-N2(adjusting the output of the 2nd side of a duplex print using plain paper)If the RAM on the DC controller PCB has been cleared, enter the value in-dicated on the service label.COPIER> ADJUST> HV-SP> HVT-SP(entering the offset value for the separation high-voltage output of the high-voltage unit)Enter the value indicated on the label attached to the new high-voltage unit if you have replaced the high-voltage unit or initialized the RAM on the DC controllerPCB.COPIER> ADJUST> HV-SP> D-HV-SP(entering the offset value for the separation high-voltage output of the DC controller PCB)Enter the value indicated on the label attached to the new DC control PCB if you have replaced the DC controller PCB or initialed the RAM on the DC controllerPCB.COPIER> OPTION> BODY> TR-SP-C1(switching over the transfer/separation output value for pickup from the right deck)COPIER> OPTION> BODY> TR-SP-C2(switching over the transfer/separation output value for pickup from the left deck)COPIER> OPTION> BODY> TR-SP-C3(switching over the transfer/separation output value for pickup from the cassette 3)COPIER> OPTION> BODY> TR-SP-C4(switching over the transfer/separation output value for pickup from the manual feed tray)COPIER> OPTION> BODY> TR-SP-MF(switching over the transfer/separation output value for pickup from the manual feed tray)COPIER> OPTION> BODY> TR-SP-DK(switching over the transfer/separation output value for pickup from various sources of paper to suit various faults)The transfer/separation output value is switched for each source of paper to prevent various problems:0: normal (default)
1: prevent re-transfer2: prevent separation3: prevent transfer faults
Chapter 7
7-20
7.10 Parts Replacement Procedure
7.10.1 Process Unit
7.10.1.1 Before Removing Process Unit0015-6484
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
7.10.1.2 Removing Process Unit 0015-4867
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the 5 connectors [1] and remove the 2 screws [2].
F-7-322) Insert the drum rotating tool [1] that comes with the unit into the slit [3]
in the drum shaft [2]. While keeping the drum in place so that it will notrotate counterclockwise, insert a screwdriver into the center opening [4]in the drum rotating tool to remove the drum fixing screw.
F-7-33
If the drum is let to rotate counterclockwise, the cleaning blade will not comeinto contact with the drum correctly, leading to poor cleaning. Thus, be sureto fix the drum in place first before removing the drum fixing screw to avoidthe problem.
MEMO: If the hopper assembly is released but not removed, be sure to open the rightcover (upper) and the right cover (lower) so that there will be space.
3) Unlock the fixing feeding unit release lever [1], and slide out the fixingfeeding unit [2].
F-7-344) Slide out the process unit [1] until it stops.
F-7-355) Hold the left grip [1] and the right grip [2] of the process unit [3] as indi-
cated, and take it out.
F-7-36
7.10.1.3 Mounting Process Unit 0015-4868
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Mount the process unit by reversing the steps used to remove it with the fol-lowing in mind: 1) On the left rail, place the process unit along the front/rear guide plates [1].
On the right rail [2], place the process unit on the L-shaped stay.
[1][2]
[2]
[4]
[3] [2]
[1]
[1] [2]
[1]
[1] [2][3]
Chapter 7
7-21
F-7-372) After sliding the process unit into the machine, insert the screw [2] by in-
serting the drum fixing tool [1]. Then, match the slot in the drum shaft andthe drum rotating tool [3], and tighten the screw [2] using the drum rotat-ing tool.
F-7-38
7.10.2 Pre-Exposure Lamp
7.10.2.1 Before Removing Pre-Exposure Lamp 0015-6490
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
2) Remove the process unit. (page 7-20)Reference[Removing ProcessUnit]
3) Remove the primary charging assembly. (page 7-21)Reference[Remov-ing Primary Charging Assembly]
4) Remove the potential sensor unit. (page 7-31)Reference[Removing Po-tential Sensor Unit]
7.10.2.2 Removing Pre-Exposure Lamp 0015-4874
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the potential sensor rail stay [2]. - 2 screws [1]
F-7-392) Remove the pre-exposure lamp unit [3].
- 1 connector [1] - 2 screws [2]
F-7-40
7.10.2.3 Cleaning Primary Toner Blocking Sheet 0016-0073
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the process unit. 2) Remove the potential sensor rail stay [2].
- 2 screws [1]
F-7-413) Clean the primary toner blocking sheet [1].
F-7-42
7.10.3 Primary Charging Assembly
7.10.3.1 Before Removing Primary Charging Assembly0015-4876
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
7.10.3.2 Removing Primary Charging Assembly 0015-4877
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Loosen the screw [1] and shift the charging assembly fixture [2] in the di-rection of the arrow (upper right); then, tighten the screw again.
2) Remove the primary charging assembly [4].- 1 connector [3]
[1] [2]
[2] [1][3]
[1][1][2]
[1][2]
[3]
[1][2] [1]
[1]
Chapter 7
7-22
F-7-43
When replacing the primary charging wire or the primary charging assem-bly, be sure to execute the following in the service mode to clean the wire:COPIER > FUNCTION > CLEANING > WIRE-CLN. Further, be sure to use a strengthened polishing pad (blue holder) as thecleaning pad.
7.10.4 Pre-Transfer Charging Assembly
7.10.4.1 Before Removing Pre-Transfer Charging Assembly
0015-4879
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
7.10.4.2 Removing Pre-Transfer Charging Assembly 0015-4880
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the pre-transfer charging assembly [3]. - 1 connector [1] - 1 screw [2]
F-7-44
Be sure to execute the wire cleaning in the user mode after mounting the pre-transfer charging assembly.
7.10.5 Photosensitive Drum
7.10.5.1 Points to Note When Handling Photosensitive Drum
0015-4881
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine’s photosensitive drum is made of high-sensitivity amorphoussilicon, and its sensitivity can start to deteriorate depending on how andwhere it is placed, requiring the following: [1] Whenever the process unit is removed from the machine or the photosen-
sitive drum is removed from the process unit, be sure to protect the pho-tosensitive drum against light. Wrap 6 or more sheets of A3 or largerpaper around the photosensitive drum.
[2] Do not place the process unit or the photosensitive drum in a area subjectto the direct rays of the sun.
[3] Do not place the process unit or the photosensitive drum in an area sub-
ject to high or low temperature or humidity or where temperature or hu-midity tends to change rapidly.
[4] Do not place the process unit or the photosensitive drum in an area sub-ject to dust, ammonium gas, or organic solvent/gas.
The foregoing requirements commonly apply to all photosensitive drums.
7.10.5.2 Before Removing Photosensitive Drum0015-6503
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
5) Remove the process unit. (page 7-20)Reference[Removing ProcessUnit]
6) Remove the primary charging assembly. (page 7-21)Reference[Remov-ing Primary Charging Assembly]
7) Remove the pre-transfer charging assembly. (page 7-22)Reference[Re-moving Pre-Transfer Charging Assembly]
8) Remove the potential sensor unit. (page 7-31)Reference[Removing Po-tential Sensor Unit]
7.10.5.3 Removing Photosensitive Drum 0015-4888
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the potential sensor rail stay [2]. - 2 screws [1]
F-7-452) Remove the gear plate [2].
- 3 screws [1]
F-7-463) Remove the front side stay [2].
- 2 screws [1]
F-7-474) Remove the photosensitive drum by holding it as indicated.
[3] [4] [2][1]
[1][2] [3]
[1][1][2]
[2]
[1]
[1]
[1] [1][2]
Chapter 7
7-23
F-7-48
Be careful not to scratch the photosensitive drum when removing it. The bearing at the rear side and the gear at the front side of the photosensitivedrum need not be removed.
If the temperature of the fixing assembly is 50 deg C or higher when replac-ing the drum unit, be sure to execute the following in the service mode; oth-erwise, the potential control will not be executed: COPIER > FUNCTION >DPC > DPC.
7.10.5.4 Cleaning Photosensitive Drum 0016-0081
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Do not rotate the magnet roller during work. Otherwise, waste toner may fallthrought the cleaner assembly.
1) Remove the process unit.2) Remove the photosensitive drum.3) Moisten lint-free paper [1] with 5 to 10 cc of alcohol solutions [2]; then,
pour 0.2 to 0.3 g of the drum cleaning powder (CK-0429) [3] on the lint-free paper.
4) While butting the lint-free paper relatively strongly against the photosen-sitive drum, wipe the surface of the drum from the front to the rear andfrom the rear to the front.
F-7-49
- Keep the widths of cleaning to 5 to 10 cm in the peripheral direction of thedrum. - Move the lint-free paper back and forth 15 to 20 times over a single area.Forcing the lint-free paper will not affect the life of the drum.
5) After the alcohol has evaporated, dry wipe the surface with the lint-freepaper. If the area is uneven, go back to the step 4, and increase the back-and-forth movements.
6) Rotate the drum for the width (5 to 10 cm), and repeat the step 3 through5 until the entire area of the surface has been cleaned.
F-7-50
7.10.6 Drum Motor
7.10.6.1 Before Removing Drum Motor 0015-6698
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Remove the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the main controller box cover.(page 10-17)Reference[Remov-ing the Main Controller Box Cover]
5) Remove the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
6) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
7) Remove the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-moving the Collecting Toner Bottle Holder]
7.10.6.2 Removing Drum Motor 0015-4904
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the flywheel [2]. - 2 screws [1]
F-7-512) Remove the drum motor [3].
- 2 connectors [1] - 4 screws [2]
[1]
[1]
[2][3]
CK-0429
5 10cm
[1][2]
Chapter 7
7-24
F-7-52
7.10.7 Photosensitive Drum Heater
7.10.7.1 Points to Note When Handling Photosensitive Drum
0015-4905
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine’s photosensitive drum is made of high-sensitivity amorphoussilicon, and its sensitivity can start to deteriorate depending on how andwhere it is placed, requiring the following: [1] Whenever the process unit is removed from the machine or the photosen-
sitive drum is removed from the process unit, be sure to protect the pho-tosensitive drum against light. Wrap 6 or more sheets of A3 or largerpaper around the photosensitive drum.
[2] Do not place the process unit or the photosensitive drum in a area subjectto the direct rays of the sun.
[3] Do not place the process unit or the photosensitive drum in an area sub-ject to high or low temperature or humidity or where temperature or hu-midity tends to change rapidly.
[4] Do not place the process unit or the photosensitive drum in an area sub-ject to dust, ammonium gas, or organic solvent/gas. The foregoing requirements commonly apply to all photosensitive drums.
7.10.7.2 Before Removing Photosensitive Drum Heater 0015-6546
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
5) Remove the process unit. (page 7-20)Reference[Removing ProcessUnit]
6) Remove the primary charging assembly. (page 7-21)Reference[Remov-ing Primary Charging Assembly]
7) Remove the pre-transfer charging assembly. (page 7-22)Reference[Re-moving Pre-Transfer Charging Assembly]
8) Remove the potential sensor unit. (page 7-31)Reference[Removing Po-tential Sensor Unit]
9) Remove the photosensitive drum. (page 7-22)Reference[RemovingPhotosensitive Drum]
7.10.7.3 Removing Drum Heater 0015-4913
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the flange [2] from the front.- 2 screws [1]
F-7-53
Protect the removed photosensitive drum against dirt and scratches by wrap-ping 5 to 6 sheets of paper or the drum protective sheet stored near the col-lecting toner container around the drum.
2) Remove the drum heater unit [1] from the rear.
F-7-543) Remove the drum heater [2].
- 1 connector [1]
F-7-55
7.10.7.4 Points to Note When Mounting Drum Heater 0015-4915
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Mount the photosensitive drum heater by reversing the steps used to removeit. However, be sure not to soil or scratches the drum and not to trap the cableof the drum heater.
7.10.8 Cleaning Blade
7.10.8.1 Configuration0015-9371
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-7-56
7.10.8.2 Before Removing Cleaning Blade 0015-9373
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
5) Remove the process unit. (page 7-20)Reference[Removing ProcessUnit]
6) Remove the primary charging assembly. (page 7-21)Reference[Remov-ing Primary Charging Assembly]
7.10.8.3 Removing Cleaning Blade0015-9374
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the 4 screws [1].
[1] [2]
[2]
[3]
[1][2]
[1]
[1]
[2]
Cleaning blade
Separation claw
Chapter 7
7-25
F-7-572) Detach the cover [2].
- 1 screw [1] [3] Free the harness from the edge saddle, and disconnect the connector [3].
F-7-584) Move the harness guide [1] in the direction of the arrow.
- 1 screw [2] 5) Put back the harness guide to its original position, and remove the cleaning
blade assembly [3].
F-7-596) Remove the pressure spring [2].
- 1 E-ring [1] (lower side of the cleaning blade assembly)
F-7-607) Remove the pre-exposure LED assembly [3].
- 1 connector [1] - 2 screws [2]
F-7-618) Loosen the 5 screws [1], and remove the cleaning blade from the blade
support plate.
F-7-62
7.10.8.4 Mounting Cleaning Blade 0015-9971
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When mounting the cleaning blade, be sure that the side with the marking [1]will be the face. 1) Push in the cleaning blade [2] until it butts slightly against the rear.
F-7-632) Tighten the 5 screws [3] lightly, and stop to turn them when resistance is
felt. 3) Turn the screws tightened lightly in the step 2 about 20 to 30 degrees in
the order indicated below, and tighten them fully.
F-7-64
After mounting the cleaning blade, check that the edge of the blade is not ex-tremely bent. Further, be sure to clean the groove in the blade support plate before mount-ing the blade, as toner or the like in the groove can be the cause the bendingof the blade. ÅB
7.10.9 Side Seal
7.10.9.1 Before Removing Side Seal 0015-9377
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
5) Remove the process unit. (page 7-20)Reference[Removing ProcessUnit]
6) Remove the primary charging assembly. (page 7-21)Reference[Remov-ing Primary Charging Assembly]
7) Remove the pre-transfer charging assembly. (page 7-22)Reference[Re-moving Pre-Transfer Charging Assembly]
8) Remove the potential sensor unit. (page 7-31)Reference[Removing Po-
[1]
[1]
[2] [3]
[1]
[2]
[3]
[2] [1]
[1]
[2]
[3]
[1]
No gap Blade retaining plate
[2] [1]
Order of tightening
5
[3]
3 1 2 4
Chapter 7
7-26
tential Sensor Unit]9) Remove the photosensitive drum. (page 7-22)Reference[Removing
Photosensitive Drum]
7.10.9.2 Removing Side Seal 0015-9973
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the old side seal. 2) Mount the new side seal [1] to the cleaner housing where indicated (both
ends). At this time, be sure that the edge of the side seal is positioned as follow: - When replacing the side seal [1] at the front, push the magnet roller [2]toward the rear, and then, make sure that the inner end of the side seal iswithin the area [3] of the washer. - When replacing the side seal [1] at the rear, push the magnet roller [2]toward the front, and then, make sure that the inner end of the side seal iswithin the area [3] of the washer.
3) The bottom end of each side seal [1] must be 0 to 0.5 mm from the cornerof the cleaner housing; i.e., point of reference [4].
4) Attach the side seal [1] at the front and the rear to the cleaner housingwhile making sure its position is as indicated.
F-7-65
7.10.10 Cleaner Scraper
7.10.10.1 Before Cleaning Cleaner Scraper 0015-9379
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
5) Remove the process unit. (page 7-20)Reference[Removing ProcessUnit]
6) Remove the primary charging assembly. (page 7-21)Reference[Remov-ing Primary Charging Assembly]
7.10.10.2 Cleaning Cleaner Scraper0016-0079
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the cleaning blade. 2) Remove any paper lint accumulated at the tip of the cleaner scraper (A;
the area between the magnet roller and the toner guide roller) with tweez-ers.
3) Remove the toner from the surface of the magnet roller. (Roll a paper intoa U-shape to scoop it up.)
F-7-66
F-7-674) Rotate the magnet roller in the clockwise direction (viewing from the
front). 5) Repeat the step 3 through 4 until the area from which toner was removed
in the step 3 is once again coated with an even layer of toner.
7.10.11 Hopper Assembly
7.10.11.1 Before Removing Hopper Assembly 0015-4917
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
7.10.11.2 Removing Hopper Assembly 0015-4918
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the right door unit (upper) [1], and remove the screw [2] from thedoor tape; then, open the unit fully.
F-7-682) Remove the developing locking assembly [2] by pushing it in the direction
0 0.5mm
[3] [2]
[1] [4]
[1]
4 8mm
A
Toner guide roller cleaner scraper (front)
Remove collected toner
(Front)
3040
mm
A
Toner guide roller
4 8mm
cleaner scraper (rear)
Magnet roller
Remove collected toner
Rear
3040
mm
[1][2]
Chapter 7
7-27
of the arrow. - 1 screw [1]
F-7-693) Remove the toner bottle. 4) Remove the hopper assembly [3].
If tilting the hopper assembly, toner will be spilled out; thus, be sure to re-move it without tilting.
- 1 connector [1] - 5 screws [2]
F-7-70
7.10.12 Hopper Supply Motor
7.10.12.1 Before Removing Toner Supply Motor 0015-8340
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Detach the right cover (upper). (page 10-12)Reference[Removing theRight Cover (Upper)]
7.10.12.2 Removing Toner Supply Motor 0015-8341
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the manual feeding tray cover. 2) Remove the 3 screws [1]. 3) Slide the lever [2] slightly upward, and detach the hopper front cover [3].
F-7-714) Remove the toner supply motor [3].
- 1 connector [1] - 3 screws [2]
F-7-72
7.10.13 Hopper Strring Motor
7.10.13.1 Before Removing Hopper Stirring Motor 0015-6673
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Detach the right cover (upper). (page 10-12)Reference[Removing theRight Cover (Upper)]
7.10.13.2 Removing Hopper Stirring Motor 0015-8342
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the cord guide [2]. - 1 connector [1]
2) Remove the hopper drive unit [4] by sliding it in the direction of the arrow. - 4 screws [3]
[1] [2]
[1]
[2]
[2] [2][3]
[1]
[1]
[2] [3]
[1]
[2]
[2]
[3]
Chapter 7
7-28
F-7-733) Free the harness from the wire saddle [2].
- 1 connector [1]
F-7-744) Remove the hopper stirring motor [2] together with the mount.
- 2 screws [1]
F-7-755) Remove the hopper stirring motor [2].
- 1 screw [1]
F-7-76
7.10.14 Developing Assembly
7.10.14.1 Removing Developing Assembly 0015-4927
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine’s developing assembly is not equipped with a cover to protectthe developing cylinder. If you must remove the developing assembly, be sure not to damage the de-veloping cylinder. When the developing assembly is outside the machine, be sure not to mountthe developing assembly locking assembly. The toner collecting in the pathfrom the hopper to the developing assembly may be strayed because of thevibration occurring during the inspection or repair work.
1) Open the right door unit (upper) [1], and remove the screw [2] from thedoor tape; then, open the unit fully.
F-7-772) Remove the developing locking assembly [2] by pushing it in the direction
of the arrow. - 1 screw [1]
F-7-783) Remove the developing assembly [2] from the machine slowly.
- 1 connector [1]
F-7-79
7.10.14.2 Cleaning Developing Toner Blocking Sheet 0016-0075
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the developing assembly, and clean the developing toner block-ing sheet [1].
[1]
[2][3]
[3]
[3] [4]
[1][2]
[1]
[1]
[2]
[1] [2]
[1][2]
[1] [2]
[1] [2]
Chapter 7
7-29
F-7-80
7.10.15 Developing Cylinder
7.10.15.1 Before Removing Developing Cylinder 0015-6675
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
2) Remove the developing blade. (page 7-29)Reference[Removing Devel-oping Blade]
7.10.15.2 Removing Developing Cylinder 0015-4931
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the gear unit [2] together with the gear. - 2 screws [1]
F-7-81
Be careful not to drop the gear when removing the gear unit because it be-comes free
2) Remove the grip ring [1] attached to the cylinder shaft at the rear; then,remove the gear [2], the parallel pin [3], and the push-on roll [4].
F-7-823) Remove the electrode plate [2].
- 2 screws [1]
F-7-834) Remove the grip ring [1] attached to the cylinder shaft at the front; then,
remove the push-on roll [2].
F-7-845) Remove the developing cylinder [2].
- 2 bearings [1] (at the front and the rear)
F-7-85
Do not leave fingerprints or oils on the surface of the developing cylinder.Otherwise, dry wipe it with lint-free paper. (Do not use solvent.)
7.10.16 Developing Blade
7.10.16.1 Before Removing Developing Blade 0015-6676
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
7.10.16.2 Removing Developing Blade 0015-4933
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the developing assembly cover [2]. - 2 mounting screws [1]
F-7-862) Place a newspaper on the floor or a desk, and pour out the toner onto the
newspaper from the developing assembly. 3) Remove the developing blade [2] together with the mount.
- 2 mounting screws [1]
F-7-87
The blade must be mounted with a high accuracy. Do not remove it on itsown in the field. Be sure to remove it together with the mount.
7.10.16.3 Mounting Developing Blade0015-4934
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Mount the blade by reversing the steps used to remove it. 1) Push the blade mount against the developing assembly, and tighten the 2
mounting screws. When mounting the blade, place a paper on the developing cylinder firstto protect the cylinder.
[1]
[1] [1][2]
[4]
[1]
[2]
[3]
[2]
[1]
[1]
[2]
[1] [2] [1]
[1] [2][1]
[1] [2] [1]
Chapter 7
7-30
7.10.17 Transfer/Separation Charging Assembly
7.10.17.1 Removing Transfer/Separation Charging Assembly
0015-4935
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover, and slide out the fixing/feeding assembly. 2) Detach the fixing/feeding unit front cover (right) [2].
- 2 screws [1]
F-7-883) Disconnect the connector [3].
- 1 screw [1] - 1 fixture [2]
F-7-894) Pull out the transfer/separation charging assembly toward the front while
holding the front and the rear of it, and remove it in the direction of upperleft.
F-7-90
Be careful not to cut the nylon wire by coming into contact the transfer/sep-aration charging assembly to the transfer guide.
7.10.17.2 Mounting Transfer/Separation Charging Assembly
0015-4936
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Mount the transfer/separation charging assembly by reversing the steps usedto remove it while keeping the followings in mind.
1) Make sure that the 4 protrusions [1] on the transfer/separation charging as-sembly are correctly fitted into the cut-offs [2] in the fixing/feeding unit.
2) Make sure that the leaf spring [3] of the fixing/feeding unit comes in con-tact with the frame of the transfer/separation charging assembly by slid-ing the assembly from the front.
F-7-91
F-7-92
F-7-933) Attach the fixing guide plate [1] with the screw [2].
F-7-944) When replacing the transfer charging wire or the transfer/separation
charging assembly, be sure to execute the following in the service modeto clean the wire: COPIER > FUNCTION > CLEANING > WIRE-CLN.
When replacing the separation charging wire, be sure to execute the wirecleaning in the user mode.
Further, be sure to use a strengthened polishing pad (blue holder) as thecleaning pad for the transfer charging wire.
7.10.18 Separation Claw/Separation Claw Drive Assembly
7.10.18.1 Before Removing Separation Claw Holder 0015-6692
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
4) Remove the developing assembly. (page 7-28)Reference[RemovingDeveloping Assembly]
5) Remove the process unit. (page 7-20)Reference[Removing ProcessUnit]
7.10.18.2 Removing Separation Claw Holder 0015-4942
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide the cover [2].
[1]
[1]
[2]
[1][2]
[3]
12
[1]
[1] [1]
[1]
[2][2]
[2]
[3]
[1]
[2]
Chapter 7
7-31
- 1 screw [1] 2) Detach the cover while pulling the separation claw holder [4] toward the
front. - 2 screws [3]
F-7-95
Be careful not to break the separation claw.
7.10.19 Potential Sensor Unit
7.10.19.1 Outline0015-4943
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The potential sensor unit includes the following 4 parts: - Potential control PCB - Potential sensor - Potential sensor relay harness (between the relay connector and thepotential control PCB) - Potential sensor harness (between the potential sensor and the relayconnector)
Be sure to replace them at the same time.
7.10.19.2 Before Removing Potential Sensor Unit 0015-6700
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
3) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
7.10.19.3 Removing Potential Sensor Unit 0015-4952
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the potential sensor unit [3].- 1 connector [1] - 1 screw [2] - Cable (free from the cable guide)
F-7-96
7.10.20 Charging Wire
7.10.20.1 Outline0015-9965
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The photosensitive drum is surrounded by 3 charging wires; the primarycharging wire, the pre-transfer charging wire, and the transfer/separationcharging wire. These charging wires are newly adopted brown wires (0.06 mm in diameter).Do not use a gold-plated wire that has been used in the past; otherwise, imagefault may occur. Further, be sure to use a strengthened polishing pad (in a blue holder) as thecleaning pad for the primary charging assembly and the transfer charging as-
sembly.
7.10.20.2 Routing Charging Wire 0015-9967
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
All charging wires (except the grid wire) are routed more or less in the sameway; the following cites the primary charging assembly. 1) Remove the shield plates (left, right) of the charging assembly. To prevent
deformation (deflection) in the primary charging assembly, be sure towork separately for the left shielding plate and the right shielding plate(do not loosen the screws [1] of both shielding plates at the same time.)
2) Remove the wire cleaner.
F-7-97
For other charging assemblies, remove the 2 covers.
3) Free a length of about 5 cm of the charging wire (0.06 mm in diameter)from the charging wire reel, and form a loop at its end with a diameter ofabout 2 mm.
MEMO: To form a loop, wind the charging wire around a hex key once, and turn thehex key 3 to 4 times; then, twist the charging wire.
4) Cut the end (excess) of the twisted wire. 5) Hook the loop on the stud.
F-7-986) At the rear, hook the charging wire on the charging wire positioning plate;
then, hook the charging wire tension spring on the charging wire whereindicated to the following figure.
F-7-997) Cut off the excess of the charging wire with nippers. 8) Pick the end of the charging wire tension spring with tweezers, and hook
it on the charging power supply electrode. In the case of the pre-transfercharging assembly, hook the spring on the pin at the front.
F-7-100
F-7-101
Make sure the followings: - The charging wire must not be bent or twisted. - The charging wire must be fitted in the V-groove of the charging wirepositioning plate.
[2] [1]
[4][3]
[1] [2][3]
[1]
Charging electrode
(Rear) (Front) Charging wire
Reel Stud
(Correct) (Wrong)
Grid side
(Correct) (Wrong)
Chapter 7
7-32
9) Attach a cushion in front of the charging wire (except the primary charg-ing assembly).
10) Attach the shield plates (left, right).
For other charging assemblies, attach the 2 covers.
11) Attach the wire cleaner. At this time, make sure the orientation of thewire cleaner.
12) Wipe the charging wire with lint-free paper moistened with alcohol so-lutions.
7.10.20.3 Routing Grid for Primary Charging Assembly 0015-9968
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Loosen the 2 screws used to secure the left and right shielding plates inplace.
2) Loosen the 3 screws used to secure the motor unit at the front in place.
F-7-1023) Loosen the screw, and move it in the direction of the arrow indicated be-
low; then, temporarily tighten it in place. 4) Free a length of about 5 cm of the charging wire (0.1 mm in diameter)
from the charging wire reel, and form a loop at its end with a diameter ofabout 2 mm.
F-7-103
MEMO:To form a loop, wind the charging wire around a hex key once, and turn thehex key 3 to 4 times; then, twist the charging wire.
5) Cut the twisted charging wire (excess) with nippers. 6) Hook the loop on the stud A. 7) After routing the wire for 31 runs, lead it through the section B, and give
it a half turn; then, put it between the washer and the monitor unit, andwind it once around the screw (clockwise), and secure it in place with thescrew.
F-7-1048) Cut the excess of the charging wire with nippers. 9) Tighten the screw loosened in the step 3.
Keep tightening until the tension of the grid wire is even. Be sure to payattention to avoid deformation (deflection) of the charging assembly (asby tightening the screw at the front of the left/right shielding plate early).
10) Tighten the screws loosened in the step 1 and 2. 11) Wipe the grid wire with lint-free paper moistened with alcohol solutions.
Make sure the followings: - The grid wire must not be bent or twisted. - The wires are laid at equal intervals. (The grid wire must be fitted in thegroove of the block.)
7.10.20.4 Adjusting Height of Charging Wire 0015-9969
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1] Primary charging wire
F-7-105Height of the charging wire <Tolerance> +/-1 mm
[2] Pre-transfer charging wire
F-7-106Height of the charging wire <Tolerance> No height adjusting mechanism
[3] Transfer charging wire
F-7-107Height of the charging wire <Tolerance> +/-2 mm
[4] Separation charging wire
F-7-108Height of the charging wire <Tolerance> +/-2 mm
MEMO:The height (position) of the primary charging wire and the transfer chargingwire can be adjusted by turning the screw at the back of the charging assem-bly. A single turn changes the position of the charging wire by about 0.7 mm.
Screws
Screw
Stud A
Screw B
7.5 1.5 0 mm7.5 1.5
0 mm
10.06 0.3 mm
9.5 0.5mm
16.0
Chapter 8 Pickup/Feeding System
Contents
Contents
8.1 Construction ...................................................................................................................................................................8-18.1.1 Specifications and construction ................................................................................................................................................... 8-18.1.2 Arrangement of Rollers and Sensors ........................................................................................................................................... 8-18.1.3 Outline of the Pickup Control System ......................................................................................................................................... 8-38.1.4 Outline of the Pickup Assembly Motor Control System ............................................................................................................. 8-5
8.2 Basic Sequence ..............................................................................................................................................................8-68.2.1 Pickup from the Right Deck ........................................................................................................................................................ 8-68.2.2 Pickup from the Cassette 3 .......................................................................................................................................................... 8-78.2.3 Pickup Retry Operation................................................................................................................................................................ 8-8
8.3 Detecting Jams ...............................................................................................................................................................8-88.3.1 Jam Detection Outline.................................................................................................................................................................. 8-8
8.3.1.1 Outline.............................................................................................................................................................................................................8-88.3.1.2 Jam History ...................................................................................................................................................................................................8-10
8.3.2 Delay Jams ................................................................................................................................................................................. 8-108.3.2.1 Cassette Pickup Assembly (right deck, left deck, cassette 3/4) ....................................................................................................................8-108.3.2.2 Other Delay Jam............................................................................................................................................................................................8-10
8.3.3 Stationary Jams .......................................................................................................................................................................... 8-118.3.3.1 Common Delay Jams ....................................................................................................................................................................................8-118.3.3.2 Power-On Stationary Jam .............................................................................................................................................................................8-12
8.4 Cassette Pick-Up Unit ..................................................................................................................................................8-128.4.1 Lifter Operation (cassette 3/4) ................................................................................................................................................... 8-128.4.2 Detecting the Presence/Absence of Paper.................................................................................................................................. 8-138.4.3 Outline of the Paper Level Detection Mechanism..................................................................................................................... 8-148.4.4 Paper Level Detection (cassette 3/4).......................................................................................................................................... 8-148.4.5 Identifying the Size of Paper (cassette 3/4) ............................................................................................................................... 8-148.4.6 Markings on the Width Guide Rail ............................................................................................................................................ 8-158.4.7 Paper Size................................................................................................................................................................................... 8-15
8.5 Manual Feed Pickup Unit ............................................................................................................................................8-178.5.1 Pickup Operation ....................................................................................................................................................................... 8-178.5.2 Detecting the Size of Paper in the Manual Feed Tray ............................................................................................................... 8-18
8.6 Deck .............................................................................................................................................................................8-198.6.1 Lifter Operation (right/left deck) ............................................................................................................................................... 8-198.6.2 Lifter Limiter (right/left deck) Control Circuit .......................................................................................................................... 8-198.6.3 Detecting the Presence/Absence of Paper.................................................................................................................................. 8-208.6.4 Outline of Paper Level Detection .............................................................................................................................................. 8-208.6.5 Paper Level Detection Operation (right/left deck)..................................................................................................................... 8-218.6.6 Identifying the Size of Paper (right/left deck) ........................................................................................................................... 8-21
8.7 Registration Unit ..........................................................................................................................................................8-218.7.1 Outline........................................................................................................................................................................................ 8-218.7.2 Control System........................................................................................................................................................................... 8-22
8.8 Duplex Feeding Unit ....................................................................................................................................................8-228.8.1 Moving the Paper to the Reversing Assembly After Printing on the 1st Side........................................................................... 8-228.8.2 Moving the Paper to the Duplexing Feed Assembly From the Reversing Assembly ............................................................... 8-228.8.3 Outline........................................................................................................................................................................................ 8-238.8.4 Sequence of Printing Operation ................................................................................................................................................. 8-238.8.5 Outline of Through-Path Operation ........................................................................................................................................... 8-248.8.6 Through-Path Operation ............................................................................................................................................................ 8-248.8.7 Outline of Horizontal Registration Position .............................................................................................................................. 8-288.8.8 Horizontal Registration Position Detection Operation .............................................................................................................. 8-28
8.9 Delivery........................................................................................................................................................................8-29
Contents
8.9.1 Reversal Delivery Operation...................................................................................................................................................... 8-298.10 Parts Replacement Procedure.................................................................................................................................... 8-31
8.10.1 Pickup Roller ........................................................................................................................................................................... 8-318.10.1.1 Before Removing the Pickup Roller ........................................................................................................................................................... 8-318.10.1.2 Removing the Pickup Roller....................................................................................................................................................................... 8-318.10.1.3 Points to Note When Mounting the Pickup Roller ..................................................................................................................................... 8-31
8.10.2 Cassette Pickup Assembly ....................................................................................................................................................... 8-318.10.2.1 Removing the Cassette 3/4 Pickup Assembly ............................................................................................................................................ 8-31
8.10.3 Cassette Pickup Motor ............................................................................................................................................................. 8-318.10.3.1 Before Removing the Cassette 3/4 Pickup Motor ...................................................................................................................................... 8-318.10.3.2 Removing the Cassette 3/4 Pickup Motor .................................................................................................................................................. 8-31
8.10.4 Cassette Lifter Motor ............................................................................................................................................................... 8-328.10.4.1 Removing the Cassette 3 Lifter Motor M20............................................................................................................................................... 8-328.10.4.2 Removing the Cassette 4 Lifter Motor M21............................................................................................................................................... 8-328.10.4.3 Adjusting the Position of the Lifter Motor M20/M21 of the Cassette 3/4 ................................................................................................. 8-33
8.10.5 Left Deck Lifter Motor ............................................................................................................................................................ 8-338.10.5.1 Before Removing the Left Deck Lifter Motor............................................................................................................................................ 8-338.10.5.2 Removing the Left Deck Lifter Motor........................................................................................................................................................ 8-33
8.10.6 Right Deck Lifter Motor .......................................................................................................................................................... 8-348.10.6.1 Before Removing the Right Deck Lifter Motor.......................................................................................................................................... 8-348.10.6.2 Removing the Right Deck Lifter Motor ..................................................................................................................................................... 8-34
8.10.7 Right Deck Pickup Assembly .................................................................................................................................................. 8-358.10.7.1 Removing the Right Deck Pickup Assembly ............................................................................................................................................. 8-35
8.10.8 Left Deck Pickup Assembly .................................................................................................................................................... 8-358.10.8.1 Removing the Left Deck Pickup Assembly................................................................................................................................................ 8-35
8.10.9 Left Deck Pickup Motor .......................................................................................................................................................... 8-368.10.9.1 Before Removing the Left Deck Pickup Motor.......................................................................................................................................... 8-368.10.9.2 Removing the Left Deck Pickup Motor...................................................................................................................................................... 8-36
8.10.10 Right Deck Pickup Motor ...................................................................................................................................................... 8-368.10.10.1 Before Removing the Right Deck Pickup Motor...................................................................................................................................... 8-368.10.10.2 Removing the Right Deck Pickup Motor ................................................................................................................................................. 8-36
8.10.11 Left Deck Pickup Sensor ....................................................................................................................................................... 8-368.10.11.1 Before Removing the Left Deck Feeding Sensor ..................................................................................................................................... 8-368.10.11.2 Removing the Left Deck Feeding Sensor ................................................................................................................................................. 8-36
8.10.12 Left Deck Pickup Solenoid .................................................................................................................................................... 8-368.10.12.1 Before Removing the Left Deck Pickup Solenoid.................................................................................................................................... 8-368.10.12.2 Removing the Left Deck Pickup Solenoid ............................................................................................................................................... 8-378.10.12.3 Adjusting the Position of the Left Deck Pickup Solenoid ........................................................................................................................ 8-37
8.10.13 Manual Feed Pull-Out Roller Unit......................................................................................................................................... 8-378.10.13.1 Removing the Manual Feeding Pickup Roller Unit.................................................................................................................................. 8-37
8.10.14 Manual Feed Pull-Out Roller................................................................................................................................................. 8-378.10.14.1 Before Removing the Manual Feeding Pickup Roller.............................................................................................................................. 8-378.10.14.2 Removing the Manual Feeding Pickup Roller.......................................................................................................................................... 8-37
8.10.15 Manual Feed Roller................................................................................................................................................................ 8-388.10.15.1 Before Removing the Manual Feeding Roller .......................................................................................................................................... 8-388.10.15.2 Removing the Manual Feeding Roller...................................................................................................................................................... 8-38
8.10.16 Manual Separation Roller ...................................................................................................................................................... 8-388.10.16.1 Before Removing the Manual Separation Roller...................................................................................................................................... 8-388.10.16.2 Removing the Manual Separation Roller.................................................................................................................................................. 8-388.10.16.3 Adjusting the Pressure of the Manual Separation Roller.......................................................................................................................... 8-38
8.10.17 Manual Feed Tray paper sensor............................................................................................................................................. 8-398.10.17.1 Removing the Manual Feeding Tray Sensor ............................................................................................................................................ 8-39
8.10.18 Registration Roller ................................................................................................................................................................. 8-398.10.18.1 Before Removing the Registration Roller ................................................................................................................................................ 8-398.10.18.2 Removing the Registration Roller ............................................................................................................................................................ 8-39
8.10.19 Pre-Registration Roller .......................................................................................................................................................... 8-408.10.19.1 Before Removing the Registration Lower Roller ..................................................................................................................................... 8-408.10.19.2 Removing the Registration Lower Roller ................................................................................................................................................. 8-40
8.10.20 Pre-Registration Motor .......................................................................................................................................................... 8-41
Contents
8.10.20.1 Before Removing the Registration Front Motor .......................................................................................................................................8-418.10.20.2 Removing the Registration Front Motor ...................................................................................................................................................8-41
8.10.21 Registration Motor ................................................................................................................................................................. 8-418.10.21.1 Before Removing the Horizontal Registration Motor...............................................................................................................................8-418.10.21.2 Removing the Horizontal Registration Motor...........................................................................................................................................8-41
8.10.22 Registration Sensor ................................................................................................................................................................ 8-428.10.22.1 Before Removing the Horizontal Registration Sensor..............................................................................................................................8-428.10.22.2 Removing the Horizontal Registration Sensor..........................................................................................................................................8-42
8.10.23 Registration Clutch ................................................................................................................................................................ 8-438.10.23.1 Before Removing the Registration Clutch ................................................................................................................................................8-438.10.23.2 Removing the Registration Clutch ............................................................................................................................................................8-43
8.10.24 Registration Brake Clutch...................................................................................................................................................... 8-438.10.24.1 Before Removing the Registration Brake .................................................................................................................................................8-438.10.24.2 Removing the Registration Brake .............................................................................................................................................................8-43
8.10.25 Feeding Roller........................................................................................................................................................................ 8-438.10.25.1 Before Removing the Feeding Roller .......................................................................................................................................................8-438.10.25.2 Removing the Feeding Roller ...................................................................................................................................................................8-438.10.25.3 The Points to Mount the Feeding Roller ...................................................................................................................................................8-44
8.10.26 Vertical Path Roller................................................................................................................................................................ 8-448.10.26.1 Before Removing the Vertical Path Roller ...............................................................................................................................................8-448.10.26.2 Removing the Vertical Path Roller ...........................................................................................................................................................8-448.10.26.3 Removing the Vertical Path Roller 2/3 .....................................................................................................................................................8-44
8.10.27 Vertical Path Motor................................................................................................................................................................ 8-448.10.27.1 Before Removing the Vertical Path Upper Motor ....................................................................................................................................8-448.10.27.2 Removing the Vertical Path Upper Motor ................................................................................................................................................8-45
8.10.28 Vertical Path Duplex Motor................................................................................................................................................... 8-458.10.28.1 Before Removing the Vertical Path Duplex Motor...................................................................................................................................8-458.10.28.2 Removing the Vertical Path Duplex Motor ..............................................................................................................................................8-45
8.10.29 Vertical Path Lower Motor .................................................................................................................................................... 8-458.10.29.1 Before Removing the Vertical Path Lower Motor ....................................................................................................................................8-458.10.29.2 Removing the Vertical Path Lower Motor................................................................................................................................................8-45
8.10.30 Reversing Motor .................................................................................................................................................................... 8-458.10.30.1 Before Removing the Reversing Motor ....................................................................................................................................................8-458.10.30.2 Removing the Reversing Motor ................................................................................................................................................................8-468.10.30.3 Mounting the Reversing Motor .................................................................................................................................................................8-46
8.10.31 Fixing Feeding Unit Releasing Lever Sensor ........................................................................................................................ 8-468.10.31.1 Before Removing the Fixing Feeding Unit Release Lever Sensor ...........................................................................................................8-468.10.31.2 Removing the Fixing Feeding Unit Release Lever Sensor .......................................................................................................................8-46
8.10.32 Reversing Sensor ................................................................................................................................................................... 8-468.10.32.1 Before Removing the Reversing Sensor 1 ................................................................................................................................................8-468.10.32.2 Removing the Reversing Sensor 1 ............................................................................................................................................................8-468.10.32.3 Before Removing the Reversing Sensor 2 ................................................................................................................................................8-478.10.32.4 Removing the Reversing Sensor 2 ............................................................................................................................................................8-47
8.10.33 Reversing Unit ....................................................................................................................................................................... 8-478.10.33.1 Before Removing the Reversing Flapper Solenoid...................................................................................................................................8-478.10.33.2 Removing the Reversing Flapper Solenoid...............................................................................................................................................8-478.10.33.3 Mounting the Reversing Flapper Solenoid ...............................................................................................................................................8-47
8.10.34 Feeding Belt ........................................................................................................................................................................... 8-488.10.34.1 Before Removing the feeding belt ...........................................................................................................................................................8-488.10.34.2 Removing the feeding belt .......................................................................................................................................................................8-48
8.10.35 Duplexing Unit....................................................................................................................................................................... 8-498.10.35.1 Before Removing the Duplex Feeding Unit..............................................................................................................................................8-498.10.35.2 Removing the Duplex Feeding Unit .........................................................................................................................................................8-49
8.10.36 Duplex Feed Motor ................................................................................................................................................................ 8-498.10.36.1 Before Removing the Duplex Feeding Left Motor ...................................................................................................................................8-498.10.36.2 Removing the Duplex Feeding Left Motor ...............................................................................................................................................8-498.10.36.3 Before Removing the Duplex Feeding Right Motor.................................................................................................................................8-498.10.36.4 Removing the Duplex Feeding Right Motor.............................................................................................................................................8-49
8.10.37 Duplex Feed Sensor ............................................................................................................................................................... 8-498.10.37.1 Before Removing the Duplex Pre-Registration Sensor ............................................................................................................................8-49
Contents
8.10.37.2 Removing the Duplex Pre-Registration Sensor ........................................................................................................................................ 8-498.10.38 Separation Roller ................................................................................................................................................................... 8-50
8.10.38.1 Before Removing the Separation Roller ................................................................................................................................................... 8-508.10.38.2 Removing the Separation Roller............................................................................................................................................................... 8-508.10.38.3 Points to Note When Mounting the Separation Roller ............................................................................................................................. 8-508.10.38.4 Adjusting the Pressure of the Deck/Cassette Separation Roller ............................................................................................................... 8-51
Chapter 8
8-1
8.1 Construction
8.1.1 Specifications and construction0015-4519
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the functions and the construction of the machine's pickup/feed system:T-8-1
8.1.2 Arrangement of Rollers and Sensors0015-4520
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Item Description
Paper movement reference center
Paper capacity paper deck (right, left) 1,500 sheets each (80 g/m2)
front cassette (3, 4) 550 sheets each (80 g/m2)
manual feed tray 50 sheets (80 g/m2)
Paper size switchover paper deck (right, left) by service person
front cassette 3, 4 by user
manual feed tray by user
Duplexing method through path
Related user mode auto cassette selection on/off
paper type registration
Related mechanical adjustment deck side registration adjustment
cassette horizontal registration adjustment
manual feed tray horizontal registration adjustment
Chapter 8
8-2
F-8-1The machine uses the following sensors to monitor the movement of paper:
T-8-2
The following shows the major rollers of the machine:T-8-3
Notation Name Notation Name
PS4 fixing claw jam sensor PS30 duplex pre-registration sensor
PS19 right deck retry sensor PS31 duplex horizontal registration sensor
PS20 left deck retry sensor PS32 right deck pull-off sensor
PS21 cassette 3 retry sensor PS33 left deck pull-off sensor
PS22 cassette 4 retry sensor PS34 duplex paper sensor
PS23 manual feed paper sensor PS35 inside delivery sensor
PS24 vertical path 1 sensor PS36 outside delivery sensor
PS25 vertical path 2 sensor PS37 reversal sensor 1
PS26 vertical path 3 sensor PS38 reversal sensor 2
PS27 vertical path 4 sensor PS46 delivery assembly jam sensor
PS28 write check sensor PS51 fixing inlet sensor
PS29 registration sensor PS52 fixing outlet sensor
Ref. Name Ref. Name
[1] manual feed roller [17] curl-imparting roller
[2] manual feed separation roller [18] duplexing outlet roller
[3] manual feed pull-off roller [19] pickup vertical path 1 roller
[4] registration roller [20] right deck pickup roller
[5] fixing upper roller [21] right deck feed roller
PS22 PS27
PS21 PS26
PS25
PS32
PS33
PS38
PS37
PS36
PS35PS51
PS52
PS19
PS20
PS46
PS4
PS24
PS30PS34PS31
PS28
PS23
PS23
[1]
[2]
[3][4][5]
[6]
[7][8]
[9]
[11]
[10]
[12]
[13]
[14][15]
[16]
[17][18]
[19]
[32]
[23]
[24]
[25]
[26]
[27]
[28]
[20]
[21][22]
[30]
[29]
[31]
Chapter 8
8-3
8.1.3 Outline of the Pickup Control System0015-4521
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The paper inside the deck/cassette is held up by the work of the lifter, and its surface remains in contact with the pickup roller, which is driven by the pickup motor(M11, M12, M24).When the pickup motor (M11, M12, M24) goes on, the pickup roller starts to rotate to feed paper into the machine.When the pickup solenoid (SL3, SL4, SL6, SL7) goes on, the pickup roller leaves the surface of the paper.The feed roller and the separation roller make sure that only a single sheet of paper is moved to the paper path; the sheet is then moved through the vertical path toreach the registration roller.The machine's pickup motor (M11, M12, M24) is equipped with a mechanism to facilitate the separation of paper. The use of a stepping motor enables the machineto slow down pickup speed.
The following is a diagram of the pickup control system used for the deck:
[6] fixing lower roller [22] right deck separation roller
[7] inside delivery roller [23] pickup vertical path 2 roller
[8] outside delivery roller [24] pickup vertical path 3 roller
[9] delivery auxiliary roller [25] cassette 3 pickup roller
[10] reversing roller [26] cassette 3 feed roller
[11] duplexing feed left roller [27] cassette 3 separation roller
[12] duplexing feed right roller [28] pickup vertical path 4 roller
[13] left deck pickup roller [29] cassette 4 pickup roller
[14] left deck feed droller [30] cassette 4 feed roller
[15] left deck separation roller [31] cassette 4 separation roller
[16] left deck pull-off roller
Ref. Name Ref. Name
Chapter 8
8-4
F-8-2The following is a diagram of the machine's cassette pickup control system:
M5M4
DC
co
ntr
olle
r P
CB
PS32
PS7PS6
SL7
SL6
PS10
PS19
PS24
PS29
PS20
PS11
PS28
M17
M25
M11
M24C
L2
Vertical path paper detection signal
Pre-registration motor drive signal
Laser write start detection signal
Registration paper detection signal
Main motor drive signal
Registration roller clutch drive signal
Vertical path duplexing feed motor drive signal
Left deck pull-off clutch signal
Left deck feed paper detection signal
Left deck pickup motor
Left deck pickup solenoid drive signal
Left deck retry signal
Left deck lifter detection signal
Left deck paper detection signal
Left deck lifter motor drive signal
Right deck pickup solenoid drive signal
Right deck pickup motor drive signal
Right deck lifter detection signal
Right deck paper detection signal
Right deck lifter motor drive signal
Right deck retry signal
Right deck feed paper detection signal
CL4
M2
PS33
Chapter 8
8-5
F-8-3
8.1.4 Outline of the Pickup Assembly Motor Control System0015-4523
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine uses 12 stepping motors of a 2-phase excitation type. Each of these motors is supplied with 24-V power by the motor drive PCB, and is turned on and off by the pulse signals from the DC controller PCB; its directionof rotation is also controlled by the DC controller PCB.The following shows the motors used in the machine's pickup assembly, and the diagram that follows shows the control circuit used for the cassette 3/4 pickupmotor (representative of all pickup motor control circuits):
T-8-4
Location Motor Remarks
Pickup system right door pickup motor (M11) error in motor leads to paper jam
left deck pickup motor (M24) same as above
cassette 3/4 pickup motor (M12) same as above
Vertical path system
vertical path upper motor (M26) same as above
vertical path lower motor (M27) same as above
vertical path duplex feed motor (M25) same as above
M12
M27D
C c
ontr
olle
r P
CB
PS26
PS13
PS17
PS27
PS14PS18
PS25
PS21
PS22
M26
SL3
SL4
Cassette 3 retry signal
Vertical path 3 paper detection signal
Vertical path upper motor drive signal
Vertical path 2 paper detection signal
Vertical path lower motor drive signal
Cassette 3/4 pickup motor drive signal
Cassette 3 pickup solenoid drive signal
Cassette 3 lifter detection signal Cassette 3 paper detection signal
Vertical path 4 paper detection signal
Cassette 4 retry signal
Cassette 4 pickup solenoid drive signal
Cassette 4 lifter detection signal
Cassette 4 paper detection signal
Chapter 8
8-6
F-8-4
8.2 Basic Sequence
8.2.1 Pickup from the Right Deck0015-4527
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- A4, 2 Prints, Continuous
Reversal/duplexing system
reversal motor (M14) same as above
duplexing feed left motor (M19) same as above
duplexing feed right motor (M18) same as above
duplexing horizontal registration motor (M16) error code "E051"
pre-registration motor (M17) error in motor leads to paper jam
others delivery motor (M13) same as above
Location Motor Remarks
Motor driver PCB
M12
A7
A8
J104
4
5
6
321
J2104
DC controller PCB
CPU
A
A*
B
B*
+24V
+24VA9
A10
A14
A10
A13
J2101
A12A9A11
+24V
Chapter 8
8-7
F-8-5
8.2.2 Pickup from the Cassette 30015-4529
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- A4, 2 Prints, Continuous
F-8-6
Start key ONor print command received
1st sheet picked up 2nd sheet picked up
Main motor (M2)
INTR PRINT LSTR STBYSTBY
[1]: stops to arch the paper at the registration roller.
Right deck pickup solenoid (SL6)
Right deck pickup motor (M11)
Right deckretry sensor (PS19)
Vertical path duplexing feed motor (M25)
Pre-registration motor (M17)
Vertical path roller 1 paper sensor (PS24)
Laser write start sensor (PS28)
Registration paper sensor(PS29)
Registration roller clutch (CL2)
[1][1]
[2]
[2]: for 2nd and subsequent jobs, stops at 20 mm from the vertical path 1 roller to control the sheet-to-sheet distance.
Cassette 4 pickup solenoid (SL3)
Cassette 3/4pickup motor (M12)
Cassette 3 retry sensor (PS21)
Vertical path 3 paper sensor (PS26)
Vertical path 2 paper sensor (PS25)
Vertical path duplexing feed motor (M25)
Pre-registration motor(M17)
Vertical path 1 paper sensor (PS24)
Vertical path lower motor (M27)
Vertical path upper motor (M26)
Start key ONor print command received
1st sheet picked up 2nd sheet picked up
Laser write start sensor (PS28)
Registration paper sensor (PS29)
Registration roller clutch (CL2)
Main motor (M2)
INTR PRINT LSTR STBYSTBY
[1] stops to arch the paper at the registration roller.[2] for 2nd and subsequent jobs, stops at 20 mm from the vertical path 3 roller to control the sheet-to-sheet distance.
[2]
[1]
Chapter 8
8-8
8.2.3 Pickup Retry Operation0015-4530
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If, because of wear on the pickup roller for example, the retry sensor (PS19, PS20, PS21, PS22) detects a delay, the machine executes a pickup retry operation. Ifa delay is once again detected after the retry operation, the machine will indicate the presence of a jam on the control panel. The machine executes a retry operation as follows and at the following timing:
F-8-7
F-8-8
8.3 Detecting Jams
8.3.1 Jam Detection Outline
8.3.1.1 Outline0015-4532
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Arrangement of the Jam Sensors
SL
M
Retry sensor
Pickup motor
Pickup roller
Pickup roller DOWN solenoid
Pickup roller
Retry sensor*1
Vertical path sensor
Retry startedDelay detected
*1 : Period of detection, determined by the clock pulses from the motor.
Thereafter, same as normal pickup sequence.
Start key ON
Chapter 8
8-9
F-8-9Types of Jams
T-8-5
Sensor Notation Delay jam Stationary jam Power-on stationary
jam
Right deck retry sensor PS19 yes no no
Left deck retry sensor PS20 yes no no
Cassette 3 retry sensor PS21 yes no no
Cassette 4 retry sensor PS22 yes no no
Right deck pull-off sensor PS32 yes yes yes
Left deck pull-off sensor PS33 yes yes yes
Vertical path 1 sensor PS24 yes yes yes
Vertical path 2 sensor PS25 yes yes yes
Vertical path 3 sensor PS26 yes yes yes
Vertical path 4 sensor PS27 yes yes yes
Write check sensor PS28 yes yes yes
Registration sensor PS29 yes yes yes
Fixing inlet sensor PS51 no no yes
Fixing claw jam sensor PS4 no yes yes
Fixing outlet sensor PS52 yes no yes
Inside delivery sensor PS35 yes yes yes
Outside delivery sensor PS36 yes yes yes
Reversal sensor 1 PS37 yes yes yes
Reversal sensor 2 PS38 yes yes yes
Duplexing paper sensor PS34 yes yes yes
PS22 PS27
PS21 PS26
PS25
PS32
PS33
PS38
PS37
PS36
PS35PS51
PS52
PS19
PS20
PS46
PS4
PS24
PS30PS34
PS28
PS29
Chapter 8
8-10
8.3.1.2 Jam History0015-4533
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine has a mechanism to keep a record of jams that occur inside it, permitting the service person to check its history of jams in service mode.
SERVICE MODE: COPIER>DISPLAY>JAMUse it to indicate jam data.COPIER>FUNCTION>CLEAR>JAM-HITSUse it to indicate the machine's jam history.
8.3.2 Delay Jams
8.3.2.1 Cassette Pickup Assembly (right deck, left deck, cassette 3/4)0015-4535
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If the leading edge of paper does not reach the sensor within a specific period of time after the motor goes on, the machine will identify the condition as being adelay jam.
F-8-10T-8-6
8.3.2.2 Other Delay Jam0015-4536
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine identifies a delay jam occurring outside its cassette/deck pickup assembly as follows:The length of time during which paper is moved from the sensor N-1 to the appropriate delay jam sensor N is monitored. If the appropriate delay jam sensor N doesnot go on within a specific period of time after the sensor NB has gone on, the machine will identify the condition as being a delay jam.
Duplexing pre-registration sensor PS30 yes yes yes
Delivery assembly jam sensor PS46 no no yes
Pickup assembly Motor N-1 Delay jam sensor N
right deck right deck pickup motor(M11) right deck retry sensor(PS19)
left deck Left deck pickup motor(M24) left deck retry sensor(PS20)
Cassette 3 Cassette 3/4 pickup motor(M12) cassette 3 retry sensor(PS21)
Cassette 4 cassette 3/4 pickup motor(M12) cassette 4 retry sensor(PS22)
Sensor Notation Delay jam Stationary jam Power-on stationary
jam
Start key ONor PRINT setting recognized
INTR / PRINT
Motor N-1
Jam check
Sensor N
[1]
Normal Error
[1]
[1] specific length of time of feed
Chapter 8
8-11
F-8-11T-8-7
8.3.3 Stationary Jams
8.3.3.1 Common Delay Jams0015-4537
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If the sensor N does not go off within a specific period of time after it has gone on, the machine will identify the condition as being a stationary jam.
F-8-12T-8-8
Sensor
right deck pull-off sensor (PS32)
left deck pull-off sensor (PS33)
vertical path 1 sensor (PS24)
vertical path 2 sensor (PS25)
vertical path 3 sensor (PS26)
vertical path 4 sensor (PS27)
write check sensor (PS28)
registration sensor (PS29)
fixing outlet sensor (PS52)
inside delivery sensor (PS35)
outside delivery sensor (PS36)
reversal sensor 1 (PS37)
reversal sensor 2 (PS38)
duplexing paper sensor (PS34)
duplexing pre-registration sensor (PS30)
Sensor
right deck pull-off sensor (PS32)
left deck pull-off sensor (PS33)
vertical path 1 sensor (PS24)
vertical path 2 paper sensor (PS25)
Start key ONor PRINT setting recognized
INTR / PRINT
Sensor N-1
Jam check
Sensor NNormal Error
[1] [1]
[1] specific length of time of feed
Start key ONor PRINT setting recognized
INTR / PRINT
Jam check
Sensor N
L + A
Normal Error
L + A
(L: paper length; A: specific feed length)
Chapter 8
8-12
8.3.3.2 Power-On Stationary Jam0015-4538
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine will identify a power-on stationary jam if paper exists over any of the following sensors when it starts initial multiple rotation at power-on:T-8-9
8.4 Cassette Pick-Up Unit
8.4.1 Lifter Operation (cassette 3/4)0015-4539
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When the cassette is pushed into the machine, the cassette open/closed sensor goes on and, at the same time, the pickup roller starts to move down. At this time, thelight-blocking plate leaves the lifter sensor, causing the cassette lifter motor to go on and the lifter to move up. When the lifter moves up and the lifter sensor detectsthe surface of paper, its ascent stops.When the open button of the cassette is pressed, the drive gear of the lifter becomes disengaged, letting the lifter to move down under its own weight.
T-8-10
vertical path 3 paper sensor (PS26)
vertical path 4 paper sensor (PS27)
write check sensor (PS28)
registration sensor (PS29)
fixing claw jam sensor (PS4)
inside delivery sensor (PS35)
outside delivery sensor (PS36)
reversal sensor 1 (PS37)
reversal sensor 2 (PS38)
duplexing paper sensor (PS34)
duplexing pre-registration sensor (PS30)
Sensor
right deck pull-off sensor (PS32)
left deck pull-off sensor (PS33)
vertical path 1 sensor (PS24)
vertical path 2 sensor (PS25)
vertical path 3 sensor (PS26)
vertical path 4 sensor (PS27)
write check sensor (PS28)
registration sensor (PS29)
fixing inlet sensor (PS51)
fixing claws jam sensor (PS4)
fixing outlet sensor (PS52)
inside delivery sensor (PS35)
outside delivery sensor (PS36)
reversal sensor 1 (PS37)
reversal sensor 2 (PS38)
duplexing paper sensor (PS34)
duplexing pre-registration sensor (PS30)
delivery assembly jam sensor (PS46)
Cassette 3 Cassette 4
Cassette opening/closing cassette 3 opening/closing cassette 4 opening/closing
Sensor
Chapter 8
8-13
The following diagram shows the components of the cassette pickup unit:
F-8-13
8.4.2 Detecting the Presence/Absence of Paper0015-4544
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The presence/absence of paper inside the deck or the cassette is checked by the cassette paper sensor.- Paper Present
F-8-14- Paper Absent
Detection sensor (PS15) sensor (PS16)
Lifter position detection cassette 3 lifter sensor (PS17) cassette 4 lifter sensor (PS18)
Paper detection cassette 3 paper sensor (PS13) cassette 4 paper sensor(PS14)
Paper level detection cassette 3 paper level detection PCB cassette 4 paper level detection PCB
(variable resistor) (variable resistor)
Lifter ascent limiter --- ---
drive motor cassette 3 lifter motor (M20) cassette 4 lifter motor(M21)
Paper sensor
Feed roller
Separation roller
Lifter
Lifter sensor
Cassette open/closed sensor
Paper
Pickup roller
Pickup roller
Retry sensor
Paper sensor Paper detecting lever
Paper
Lifter
Chapter 8
8-14
F-8-15
8.4.3 Outline of the Paper Level Detection Mechanism0015-4545
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine indicates the amount of paper inside the deck and the cassette in terms of 4 levels (including absence of paper) on its control panel:T-8-11
8.4.4 Paper Level Detection (cassette 3/4)0015-4546
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine checks the amount of paper remaining based on the reading of a variable resistor that operates in conjunction with the movement of the lifter driveshaft.
F-8-16
SERVICE MODE:COPIER> ADJUST> CST-ADJ> C3-LVOLIndicates the value when 50 sheets of paper exist in cassette 3.COPIER> ADJUST> CST-ADJ> C3-HVOLIndicates the value when 275 sheets of paper exist in cassette 3.COPIER> ADJUST> CST-ADJ> C4-LVOLIndicates the value when 50 sheets of paper exist in cassette 4.COPIER> ADJUST> CST-ADJ> C4-HVOLIndicates the value when 275 sheets of paper exist in cassette 4.
8.4.5 Identifying the Size of Paper (cassette 3/4)0015-4547
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
OutlineThe machine uses the paper size sensor mounted to the rear of the cassette holder to identify the size of paper inside the cassette.When the cassette is slid into the cassette holder, the paper size sensor is pushed by the boss on the cassette, permitting the machine to detect the width and thelength of paper. The DC controller PCB identifies the size of the paper with reference to the combination of its width and length, and communicates the result ofidentification to the controller unit and the reader unit.The boss pushing the paper size sensor works in conjunction with the guide plate inside the cassette, and its location is determined when the guide plate is set tosuit a specific paper size.
Identifying the Size PaperThe paper length sensor consists of 2 photointerrupters, and the combination of its 2 outputs is used to find out the length of paper.The paper width sensor, on the other hand, is a variable resistor, and the machine refers to the reading (resistance) of the sensor to find out the width of paper.
3 bars 100% to about 50% of capacity
2 bars about 50% to about 10% of capacity
1 bar 10% or less of capacity
no bar no paper
Paper sensorPaper detecting lever
Lifter
Level of paper (high)
Level of paper (low)
Variable resistor
Variable resistor
Chapter 8
8-15
F-8-17T-8-12
8.4.6 Markings on the Width Guide Rail0015-4548
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The width guide rail mounted inside the cassette is provided with paper size detecting holes identified by means of markings from A through M.If the user reports skew movement, for instance, ask him/her to communicate the marking so that you will know if the paper width is correctly set. (The purpose of these markings is not disclosed to the user.)
T-8-13
8.4.7 Paper Size0015-4550
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The CPU on the DC controller PCB identifies the size of paper used based on paper width and paper length. The result of identification is communicated to thecontroller unit.
Cassette 3 Cassette 4
Paper length detectionUN18 UN19
Paper width detection UN16 UN17
Marking Paper RemarksA STMT-RB A5-RC B5-RD KLGL-RE GLTR-RF G-LGL U3G A4-RH LGL/LTR-RI FLSC U2J B4/B5K G-LTR U1L 279.4 x 431.8mm U4
(11" x 17" )/ LTRM A3/A4
Paper width detecting VR
Paper length sensor unit
Width guide (rear)
Width guide (front)
CassetteLength guide
Chapter 8
8-16
F-8-18The following sizes are grouped and specified in service mode. A size identified by an asterisk is a default paper size as selected at time of shipment from the factory.
T-8-14
SERVICE MODE:COPIER> OPTION> CST> CST-U131: G-LTR *, 22: K LGLCOPIER> OPTION> CST> CST-U224: FLSC *, 26: OFI, 27: E-OFI, 36: A-OFI, 37: M-OFICOPIER> OPTION> CST> CST-U334: G-LGL *, 35: FOLI, 25: A-FLSCOPIER> OPTION> CST> CST-U418: LTR *, 29: A-LTR*: factory settingCOPIER> ADJUST> CST-ADJ> C3-STMTRUse it to change the paper width basic value for STMTR in cassette 3.COPIER> ADJUST> CST-ADJ> C3-A4RUse it to change the paper width basic value A4R in cassette 3.COPIER> ADJUST> CST-ADJ> C4-STMTRUse it to change the paper width basic value for STMTR in cassette 4.COPIER> ADJUST> CST-ADJ> C4-A4RUse it to change the paper width basic value for A4 in cassette 4.
- Paper Types That May Be Used for the MachineT-8-15
Group Size
U1 * G-LTR
K-LGL
U2 * FOOLSCAP
OFFICIO
E-OFFI
A-OFFI
M-OFI
U3 * G-LGL
FOLIO
AUS-FLS
* LTR
A-LTR
Name Notation Size (vertical x horizontal; mm)
A3 A3 (297 +/- 1) x (420 +/- 1)
A4R A4R (210 +/- 1) x (297 +/- 1)
PS102/ PS101/ PS102/ PS101/ PS102/ PS101/ PS102/ PS101/PS104
SZ 2 SZ 1 SZ 2 SZ 1 SZ 2 SZ 1 SZ 2 SZ 1
PS103 PS104 PS103 PS104 PS103 PS104 PS103
0
A4 A3- -
(U4)
288.5279.4 x
431.8mm(11
,,x17
,,,)
- -
(U1) -- -
B5 B4- -
STMTR -- -
A5R -- -
B5R -- -
K-LGLR -- -
G-LTRR --
A5 -A4R(U3)
STMT LGLLTRR (U2)
0 0 1 1 0 1 1
273.7
261.8
238.0
212.9
206.6
196.6
186.0
165.2
144.1
ON/OFF
Paper lengthsensor
SignalPaperwidth sensor(slice level)Unit: mm
Chapter 8
8-17
8.5 Manual Feed Pickup Unit
8.5.1 Pickup Operation0015-4551
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The presence/absence of paper in the manual feed tray is detected by the manual feed paper sensor (PS23). The manual feed pull-off roller is operated by the drivecoming from the main motor by way of the manual feed pickup clutch (CL3).When the clutch engages, the holding plate solenoid goes on so that the manual feed holding plate moves up.In response, the gear of the feed roller receives the drive of the main motor, causing the feed roller to make a single rotation for movement of paper.While the feed roller is rotating, the paper is moved by the manual feed roller as far as the registration roller.
A4 A4 (297 +/- 1) x (210 +/- 1)
A5 A5 (210 +/- 1) x (148.5 +/- 1)
A5R A5R (148.5 +/- 1) x (210 +/- 1)
B4 B4 (257 +/- 1) x (364 +/- 1)
B5R B5R (182 +/- 1) x (257 +/- 1)
B5 B5 (257 +/- 1) x (182 +/- 1)
11 x 17 11 x 17 (279 +/- 1) x (432 +/- 1)
LTRR LTRR (216 +/- 1) x (279 +/- 1)
LTR LTR (279 +/- 1) x (216 +/- 1)
STMT STMT (216 +/- 1) x (139.5 +/- 1)
STMR STMTR (139.5 +/- 1) x (216 +/- 1)
LEGAL LGL (216 +/- 1) x (356 +/- 1)
Korean Government K-LGL (265 +/- 1) x (190 +/- 1)
Korean Government R K-LGLR (190 +/- 1) x (265 +/- 1)
FOOLSCAP FLSC (216 +/- 1) x (330 +/- 1)
Australian Australian Foolscap A-FLS (206 +/- 1) x (337 +/- 1)
OFICIO OFI (216 +/- 1) x (317 +/- 1)
Ecuadorian Officio E-OFI (220 +/- 1) x (320 +/- 1)
Bolivian Officio B-OFI (216 +/- 1) x (355 +/- 1)
Argentine LTR A-LTR (280 +/- 1) x (220 +/- 1)
Argentine LTRR A-LTRR (220 +/- 1) x (280 +/- 1)
Government LTR G-LTR (267 +/- 1) x (203 +/- 1)
Government LTRR G-LTRR (203 +/- 1) x (267 +/- 1)
Argentine LGL A-LGL (220 +/- 1) x (340 +/- 1)
Government LGL G-LGL (203 +/- 1) x (330 +/- 1)
FOLIO FOLI (210 +/- 1) x (330 +/- 1)
Argentine Officio A-OFI (220 +/- 1) x (340 +/- 1)
Mexico Officio M-OFI (216 +/- 1) x (341 +/- 1)
Name Notation Size (vertical x horizontal; mm)
Chapter 8
8-18
F-8-19
8.5.2 Detecting the Size of Paper in the Manual Feed Tray0015-4552
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The user may set the side guide of the manual feed tray to suit the width of paper he/she is using. The reading of the variable resistor that operates in conjunctionwith the movement of the side guide is monitored by the DC controller PCB for detection of paper width. The machine does not have a specific mechanism to detectthe length of paper, requiring the user to specify it.The width that has been detected is used when the machine executes laser exposure control. The machine refers to the length of time during which the manual feedpaper sensor (PS23) remains on to find out the length of paper when the manual feed tray is used.If the variable resistor has been replaced, the paper width basic value must be registered newly.
F-8-20
SERVICE MODE:COPIER> ADJUST> CST-ADJ> MF-A4RUse it to change the paper width basic value for A4R in the manual feed tray.COPIER> ADJUST> CSRT-ADJ> MF-A6RUse it to change the paper width basic value for A6R in the manual feed tray.COPIER> ADJUST> CST-ADJ> MF-A4Use it to change the paper width basic value for A4 in the manual feed tray.
M1
CL2
CL3
SL2
Reg
istra
tion
rolle
r clu
tch
drive
sig
nal
Man
ual fe
ed p
ickup
clu
tch
drive
sig
nal
Mai
n m
otor
driv
e sig
nal
Man
ual fe
ed re
leas
e so
leno
id d
rive
signa
l
Manual feed pull-off roller
Registration roller
Feed roller
Separation roller
Manual feed holding plate Tray
Paper
Man
ual fe
ed p
aper
det
ectio
n sig
nal
DC controller PCB
A
A
PS23
DC controller PCB
Variable resistor
Side guide (rear)
Side guide (front)
Manual feed tray
Man
ual f
eed
tray
pap
er w
idth
de
tect
ion
sign
al
Chapter 8
8-19
8.6 Deck
8.6.1 Lifter Operation (right/left deck)0015-4553
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When the deck is slid into the machine, the deck open/closed sensor goes on and, at the same time, the pickup roller starts to move down. While all this goes on,the light-blocking plate leaves the lifter sensor, causing the deck lifter motor to go on and the lifter to move up.The lifter stops to move up when the lifter sensor detects the surface of paper. The left/right deck, further, is equipped with a limiter to make sure that the lifter stopsbefore it moves past the lifter sensor.When the open button of the deck or the cassette is pushed, the drive gear of the lifter becomes disengaged, letting the lifter to move down under its own weight.
T-8-16
The following diagram shows the components of the deck:
F-8-21
8.6.2 Lifter Limiter (right/left deck) Control Circuit0015-4555
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When the CPU on the DC controller PCB generates the motor drive signal, the lifter motor in response starts to rotate to move the lifter. When the deck reaches thelifter sensor, the deck lifter detection signal arrives at the CPU, causing the CPU to stop the deck lifter drive motor.The machine is equipped with a deck limit sensor to make sure that the lifter will not go awry. When the surface of paper reaches the deck limit sensor, the limitsignal arrives at the DC controller PCB to cut off the drive signal, thereby stopping the limit motor.The following block diagram shows the control circuit:
Right deck Left deck
Cassette opening/closing right deck left deck
Detection open/closed sensor (PS5) open/closed sensor (PS9)
Lifter position detection Right deck lifter sensor(PS6) left deck lifter sensor (PS10)
Paper detection right deck paper sensor (PS7) left deck paper sensor (PS11)
Paper level sensor right deck paper level upper sensor (PS47)
left deck paper level upper sensor (PS49)
right deck paper level lower sensor (PS48)
left deck paper level lower sensor(PS50)
Lifter upper limiter right deck limit sensor (PS8) left deck limit sensor(PS12)
Drive motor right deck lifter motor (M4) left deck lifter motor(M5)
Paper sensor
Paper detecting lever
Feed roller
Separation roller
Lifter
Paper
Deck open/closed sensor
Lifter sensor
Pickup roller
Pickup roller
Retry sensor
Lift position lever
Limiter sensor
Chapter 8
8-20
F-8-22
F-8-23
8.6.3 Detecting the Presence/Absence of Paper0015-4556
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The presence/absence of paper inside the deck or the cassette is checked by the cassette paper sensor.- Paper Present
F-8-24- Paper Absent
F-8-25
8.6.4 Outline of Paper Level Detection0015-4559
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine indicates the amount of paper inside the deck and the cassette in terms of 4 levels (including absence of paper) on its control panel:
M4
Motor driver PCB
CPU
Right deck limit sensorPS8
DC controller PCB
Motor drive signal 5
6
B8
J112
J2105
Right deck lifter limit signal
1
J2113
7
J105
Right deck lifter sensorPS6
Right deck lifter detection signal
A2
J112
Limit detection circuit
Right deck lifter drivemotor
M5
Motor driver PCB
CPU
Left deck limit sensorPS12
DC controller PCB
Motor drive signal 3
4
A2
J115
J2105
Left deck lifter limit signal
2
J2113
6
J105
Left deck lifter sensorPS10
Left deck lifter detection signal
A5
J115
Limit detection circuit
Left deck lifter drivemotor
Paper sensor Paper detecting lever
Paper
Lifter
Paper sensorPaper detecting lever
Lifter
Chapter 8
8-21
T-8-17
8.6.5 Paper Level Detection Operation (right/left deck)0015-4560
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine uses 2 sensors to check the position of the deck bottom plate, and checks the level of paper based on the combination of sensor states (on/off).The machine uses a special sensor to check the presence/absence of paper.
F-8-26T-8-18
8.6.6 Identifying the Size of Paper (right/left deck)0015-4561
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The right/left deck does not possess a mechanism to detect the size of paper, and the machine finds out the size of paper as follows:(A4, B5, LTR)[1] The position of the paper size guide plate of the cassette is changed.
[2] A paper size is registered in service mode.
SERVICE MODE:COPIER> OPTION> CST> P-SZ-C1Use it to specify a paper size for the right deck.Settings:6: A4, 15: B5, 18: LTRCOPIER> OPTION> CST> P-SZ-C2Use it to specify a power size for the left deck.Settings6: A4, 15: B5, 18: LTR
8.7 Registration Unit
8.7.1 Outline0015-4563
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The registration clutch serves to make sure that the print paper and the image on the drum will match at a specific point. The timing at which the registration rollerclutch goes on may be varied in service mode (ADJUST>FEED-ADJ>REGIST).
3 bars 100% to about 50% of capacity
2 bars about 50% to about 10% of capacity
1 bar 10% or less of capacity
no bar no paper
Right deck Left deck
Paper level [1] sensor (PS47)
[2] sensor (PS48)
sensor (PS7) [1] sensor (PS49)
[2] sensor (PS50)
sensor (PS11)
100% to about 50% ON ON ON ON ON ON
about 50% to about 10% OFF ON ON OFF ON ON
about 10% or less OFF OFF ON OFF OFF ON
no paper OFF OFF OFF OFF OFF OFF
Paper level(100% to
about 50%)
Paper level(about 50%
to about 10%)
Paper level(about 10%
or less)
[1]
[2] [2] [2]
[1] [1]
Chapter 8
8-22
8.7.2 Control System0015-4565
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-8-27
8.8 Duplex Feeding Unit
8.8.1 Moving the Paper to the Reversing Assembly After Printing on the 1st Side0015-4566
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-8-28
8.8.2 Moving the Paper to the Duplexing Feed Assembly From the Reversing Assembly0015-4567
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
DC controller PCB
Main motor
M2CL2
Registration drive signal
Registration roller
PS36
PS38
PS37
PS46
Reversing flapper
Delivery flapperPS29
M14
SL8
SL5
Rev
ersi
ng fl
appe
r so
leno
id d
rive
sign
al
Del
iver
y as
sem
bly
jam
det
ectio
n si
gnal
Del
iver
y fla
pper
sol
enoi
d dr
ive
sign
al
Ins
ide
pape
r se
nsor
driv
e si
gnal
Cla
w ja
m d
etec
tion
sign
al
Fix
ing
outle
t pap
er d
etec
tion
sign
al
Fix
ing
inle
t pap
er d
etec
tion
sign
al
Rev
ersa
l det
ectio
n si
gnal
2
Reg
istr
atio
n pa
per
dete
ctio
n si
gnal
Rev
ersa
l mot
or d
rive
sign
al
DC controller PCB
PS51
PS4
PS52
PS35
Chapter 8
8-23
F-8-29
8.8.3 Outline0015-4569
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The paper path for the 1st side of a duplex print is formed when the reversing flapper solenoid (SL8) goes on to move up the reversing flapper.When printing on the 1st side is done and the leading edge of paper reaches the delivery assembly jam detection sensor (PS4), the reversing flapper solenoid goeson. When the delivery assembly jam sensor (PS46) goes on and the paper arrives at a specific point, the reversal motor (M14) starts to rotate to move the paper tothe duplexing reversing assembly. When the paper reaches the reversal sensor 2 (PS38) and then a specific point, the reversal motor (M14) stops to rotate so thatthe paper is kept on hold at the reversing assembly.Thereafter, when the reversal motor (M14) starts to rotate in reverse, the paper in the reversing assembly is moved toward the duplexing wait point by the work ofthe duplexing feed left/right roller, which is operated by the drive from the duplexing feed left/right motor (M19, M18). When the paper reaches the duplexingrepickup point (before 40mm of the curling roller), the parer stops and the horizontal registration operation is executed.The paper is then moved to the duplexing wait point as soon as the duplexing feed left/right motor (M19, M18) starts to rotate again.
MEMO:The paper is not arched. (both case thick paper mode and plain paper mode)
8.8.4 Sequence of Printing Operation0015-4570
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
PS31PS34
M18 M25
PS38
PS37 PS24
PS35PS29
PS30
PS46
Duplexing outlet roller
Duplexing feed right roller
Reversing roller
Duplexing feed left roller
Curl-imparting roller
PS28
M14S
L8M19
Rev
ersi
ng fl
appe
r so
leno
id d
rive
sign
al
Rev
ersa
l det
ectio
n si
gnal
1
Rev
ersa
l mot
or d
rive
sign
al
Rev
ersa
l det
ectio
n si
gnal
2
Dup
lexi
ng fe
ed le
ft m
otor
driv
e si
gnal
Dup
lexi
ng h
oriz
onta
l reg
istr
atio
n si
gnal
Dup
lexi
ng p
aper
det
ectio
n si
gnal
Dup
lexi
ng fe
ed r
ight
mot
or d
rive
sign
al
Dup
lexi
ng p
re-r
egis
trat
ion
pape
r si
gnal
Ver
tical
pat
h du
plex
ing
feed
mot
or d
rive
sign
al
DC controller PCB
Chapter 8
8-24
F-8-30
8.8.5 Outline of Through-Path Operation0015-4571
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The through-path mechanism is used to move paper to the duplexing feed assembly after fixing (and after the paper has been moved to the reversing assembly bythe work of the reversing flapper).The machine is designed to reorder pages in its memory for printing, being free of the need to print originals in sequence and being, therefore, able to reduce thetime during which paper is kept on hold, ultimately bringing about faster duplexing operation. As many as 2 sheets of paper may exist at once between the regis-tration sensor and the duplex paper sensor.
SERVICE MODE:COPIER> ADJUST> FEED-ADJ> ADJ-REFEUse it to adjust the write start position in main scanning direction at time of re-pickup.(-50 to 50 mm)
8.8.6 Through-Path Operation0015-4573
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following cites through-path operation when making duplex prints of 10 originals:1. The 1st sheet is picked up from the right deck.
F-8-312. The 1st side is printed on the 1st sheet.
The 2nd sheet is picked up.
Pulled in Pushed out
Start key ON or PRINT setting recognizedOriginal placed in ADF
face of 1st sheet printed
back of 2nd sheet printed
back of 1st sheet printed
back of 2nd sheet printed
Pickup motor (M2)
Claw jam sensor(PS4)
Delivery flapper solenoid (SL5)
Reversal motor (M14)
Duplexing feed left motor (M29)Duplexing feed right motor (M18)
Vertical path duplexing feed motor (M25)
Duplexing pre-registration sensor(PS30)
Duplexing paper sensor (PS34)
Reversal sensor 1 (PS37)
Reversal sensor 2 (PS38)Reversal flapper solenoid (SL8)
A4, 4 Originals, Duplexing
Inside delivery sensor (PS35)
[1]
[1] stops for arching at the duplexing feed right roller.[2] stops to control the sheet-to-sheet distance at the duplexing wait point.
Horizontal registration sensor (PS31)
[2]
Pulled in Pushed out
[1] [2]
Fixing outlet sensor(PS52)
Chapter 8
8-25
F-8-323. The 3rd side is printed on the 2nd sheet.
The 1st sheet is moved to the reversing assembly.The 3rd sheet is picked up.
F-8-334. The 1st sheet is moved to the duplexing feed assembly.
F-8-345. The 1st sheet is moved to the duplexing wait point.
The 2nd sheet is moved to the reversing assembly.The 5th side is printed on the 3rd sheet.
F-8-356. The 1st sheet is re-picked up at the duplexing wait point.
The 2nd sheet is moved to the duplexing feed assembly.
1
3
1
3
5
3
1
Chapter 8
8-26
F-8-367. The 2nd side is printed on the 1st sheet.
The 2nd sheet is moved to the duplexing wait point.The 4th sheet is picked up.
F-8-378. The 7th side is printed on the 4th sheet, and the 1st sheet is delivered.
F-8-389. The 4th side is printed on the 2nd side, and the 3rd sheet is kept on hold at the duplexing wait point.
The 5th sheet is picked up.
F-8-3910. The 2nd sheet is delivered.
The 9th side is printed on the 5th sheet.
F-8-40
1
5
3
5
3
1
2
72
5
3
1
5
2 1
7
4
3
2 1
4
3 9
5
7
Chapter 8
8-27
11. The 6th side is printed on the 3rd sheet.The 4th sheet is kept on hold at the duplexing wait point.
F-8-4112. The 3rd sheet is delivered.
F-8-4213. The 8th side is printed on the 4th sheet.
F-8-4314. The 4th sheet is delivered, and the 10th side is printed on the 5th sheet.
F-8-4415. The 5th sheet is delivered.
F-8-45
6
5
9
7
4 3
2 1
6
5
7
4 3
2 1
9
8
7
9
4 3
6 5
2 1
8
9
7
4 3
6 5
2 1
10
9
6 5
8 7
2 1
4 3
Chapter 8
8-28
8.8.7 Outline of Horizontal Registration Position0015-4574
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-8-19
F-8-46
8.8.8 Horizontal Registration Position Detection Operation0015-4575
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine executes home position detection of the duplexing horizontal registration sensor when the main power switch is turned on, when jam recovery is start-ed, or when the front cover is closed. The registration sensor goes on, and moves to the start position (A4 detection position).When the paper moves from the duplexing feed assembly and reaches the duplex paper sensor (PS34), the horizontal registration motor (M16) goes on, and theduplex horizontal registration sensor (PS31) stars to check the edge of paper while the paper stops at the duplexing repickup point and for each duplexing session.The machine checks the paper width indicated by the slide guide of the manual feed tray assembly and the cassettes size when the registration sensor goes on, todetermine the point at which detection is to be started (a point about 10 mm from the edge of paper assuming ideal movement of paper).The start position is used as the point of reference, and the machine identifies the paper position taking into account the likely displacement based on the numberof drive pulses from the motor (1 pulse = about 0.16 mm).
F-8-47*1: The edge of paper and the contact with the sensor are detected in the absence of the light-blocking plate.
*2: The start position (SP) varies as the paper edge position varies depending on the size of paper.
Paper position detection duplexing horizontal registration sensor (PS31)
Timing of start of detection after duplexing paper sensor (PS34) goes on
Source of drive duplexing horizontal registration motor (M16)
Position measurement by controlling pulses of duplexing horizontal registration motor (1 pulse = about 0.16 mm)
Related service mode COPIER> ADJUST> FEED-ADJ> ADJ-REFE
M16
PS31
Home position
Detection start position
paper edge
paper
10mm
INTR/STBY PRINT
H.P
S.P*1
Duplexing feed right motor (M19)
Registration sensor(PS29)
Duplexing paper sensor(PS34)
Duplexing horizontal registration motor (M16)
Duplexing horizontal registration sensor(PS31)
Duplexing horizontal registration sensor (PS31) position
Power edge
Main power switch ON
Reverse Forward Forward
Reverse
10 mm (approx.)
100 msec (approx.)
Chapter 8
8-29
HP: start position of the duplexing horizontal registration sensor.SP: start position of the duplexing horizontal registration sensor.
8.9 Delivery
8.9.1 Reversal Delivery Operation0015-4576
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine offers both face-up delivery and face-down delivery.T-8-20
The following shows the operation of the machine at time of reversal delivery in face-down delivery mode.1. The sheet is moved to the duplexing feed assembly.
F-8-482. The inside delivery sensor (PS35) goes on and the paper moves over a specific distance; then, the reversal motor (M14) goes on to stop the trailing edge of paper
at the point of reversal, timed to coincide with the activation of the reversal sensor 1 (PS37).
F-8-493. The reversal motor (M14) starts to rotate once again, and the trailing edge of paper is moved in the direction of delivery.
F-8-504. When the trailing edge of paper moves past the reversing roller coinciding with the activation of the outside delivery sensor (PS36), the reversal motor (M14)
stops. The delivery motor (M13) starts to rotate to move the paper to the outside delivery roller, which discharges the paper to the outside of the machine.
Delivery mode Operation mode
Face-up - making multiple prints of a single original
- for the following, when the manual feed tray is used as the source of paper: with a default paper size selected and paper other than plain paper used
Face-done - operation modes other than the above
PS37
PS35
M14
Inside delivery roller
Reversing flapper
Point of reversal
PS37
PS35
M14
Reversing flapper
Print of reversal
PS37
PS37
PS46
M14
Reversing flapper
Print of reversal
PS37
Chapter 8
8-30
F-8-51
PS36
M19
M14
Reversing flapper
Outside delivery roller
Point of reversal
PS37
Chapter 8
8-31
8.10 Parts Replacement Procedure
8.10.1 Pickup Roller
8.10.1.1 Before Removing the Pickup Roller0015-4961
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the right deck pickup assembly. (page 8-35)Reference[Remov-ing the Right Deck Pickup Assembly]
2) Remove the cassette pickup assembly. (page 8-31)Reference[Removingthe Cassette 3/4 Pickup Assembly]
3) Remove the left deck pickup assembly. (page 8-35)Reference[Remov-ing the Left Deck Pickup Assembly]
8.10.1.2 Removing the Pickup Roller0015-4965
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the pickup roller [2] in the direction of the arrow.- 2 resin E-rings [1]
F-8-52
8.10.1.3 Points to Note When Mounting the Pickup Roller0016-0018
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Å°The direction of the mounting pickup rollerThe pickup roller may be mounted by reversing the steps used to remove it;however, be sure to keep the following in the mind.
- The roller used at the front and the rear of the machine is not compatible.- When mounting the pickup roller used at the front of the machine [1],make sure the round mark [2] and the punch mark [3] found on the sideof the roller are toward the front of the machine.
F-8-53- When mounting the pickup roller used at the rear of the machine [1],make sure the punch mark [2] is at the rear of the machine.
F-8-54
8.10.2 Cassette Pickup Assembly
8.10.2.1 Removing the Cassette 3/4 Pickup Assembly0015-4967
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The steps to remove the cassette 3 pickup assembly and the cassette 4 pickupassembly are the same.
1) Slide out the cassette 3/4.2) Open the right door unit (rear).
An attempt to remove the pickup assembly without removing the cassettecauses the lifter get trapped and may hold the pickup assembly from slidingout.
3) Disconnect the connector [3].- 1 screw [1]- 1 connector cover [2]
4) Remove the cassette 3/4 assembly [5].- 3 screws [4]
F-8-55
8.10.3 Cassette Pickup Motor
8.10.3.1 Before Removing the Cassette 3/4 Pickup Motor0015-4968
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Remove the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the main controller box cover.(page 10-17)Reference[Remov-ing the Main Controller Box Cover]
5) Remove the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
6) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
7) Remove the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-moving the Collecting Toner Bottle Holder]
8.10.3.2 Removing the Cassette 3/4 Pickup Motor0015-4974
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the harness [1] from the 9 wire saddles.- 10 connectors
2) Remove the motor driver PCB mounting base [3].- 4 screws [2]
[1]
[2]
Direction ofrotation
Front side ofthe machine
[1]
[2]
[3]
Direction ofrotation
Rear side ofthe machine
[1]
[2][2]
[1]
[2]
[5]
[4]
[3]
Chapter 8
8-32
F-8-563) Remove the cassette 3/4 pickup motor [2].
- 2 screws [1]
F-8-57
8.10.4 Cassette Lifter Motor
8.10.4.1 Removing the Cassette 3 Lifter Motor M200015-4977
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide out the right deck and cassette 3/4.2) Remove the ducker of the cassette 3 [1].
F-8-583) Open the lower right cover.4) Detach the cassette right cover [2].
- 3 screws [1]
F-8-595) Remove the cassette 3 lifter motor M20 [3].
- 2 fixing screws [1]- 1 connector [2]
F-8-60
8.10.4.2 Removing the Cassette 4 Lifter Motor M210015-4978
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide out the right deck and the cassette 3/4.2) Remove the ducker of the cassette 3 [1].
F-8-613) Open the lower right cover.4) Detach the cassette right cover [2].
- 3 screws [1]
[1] [1]
[1][2] [2]
[2] [2][3]
[1][2]
[1]
[1][2]
[1]
[1]
[3] [2]
[1]
[1]
Chapter 8
8-33
F-8-625) Remove the cassette 4 lifter motor M21 [3].
- 2 fixing screws [1]- 1 connector [2] (Free the connector cable from the wire saddle)
F-8-63
8.10.4.3 Adjusting the Position of the Lifter Motor M20/M21 of the Cassette 3/4
0016-0031
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the cable from the wire saddle, and detach the guide plate [3].- 1 connector [1]- 3 screws [2]
F-8-642) While keeping the lifter motor M21/M21 [1] to the right side, tighten the
screw [2] temporally.
F-8-653) Set the cassette 3/4 in the machine without paper.4) Check to make sure the lifer drive guar [1] is engaged with the lifter motor
guar [2] from the right side of the machine.5) Check to make sure the lifter drive guar is fully away from the lifter motor
guar when the release button of the cassette 3/4 [3] is pressed halfway.
The condition of “pressing released button halfway” is following.- Separation roller should move down.- The cassette roller is about to slide out.
F-8-666) If the lifter drive guar is not away from the lifter motor, move the position
of the lifter motor M20/M21 [1] to the left and check again with keepingthe release button of the cassette 3/4 pressed halfway.
F-8-677) Fully tighten the 2 screws of the lifter motor M20/M21.8) Mount back the removed parts and turn the machine on.9) Check to make sure the cassette can be fully slid out when the cassette re-
lease button is pressed under the following conditions.- The cassette contains no paper- The cassette contains about 550 paper
8.10.5 Left Deck Lifter Motor
8.10.5.1 Before Removing the Left Deck Lifter Motor0015-4980
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the HVT PCB. (page 10-28)Reference[Removing HVT PCB]
8.10.5.2 Removing the Left Deck Lifter Motor0015-4982
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the 2 wire saddles [1] and free the 2 harnesses [2].2) Remove the left deck lifter drive assembly [5].
- 3 screws [3]- 2 connectors [4]
[1][2]
[1]
[1]
[1] [2]
[3]
[1]
[3][1]
[2]
[2]
[1]
[2]
[1]
[2][2]
[1]
Chapter 8
8-34
F-8-683) Remove the left deck lifter motor [2].
- 3 screws [1]
F-8-69
8.10.6 Right Deck Lifter Motor
8.10.6.1 Before Removing the Right Deck Lifter Motor0015-4983
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Remove the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the main controller box cover.(page 10-17)Reference[Remov-ing the Main Controller Box Cover]
5) Remove the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
6) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
7) Remove the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-moving the Collecting Toner Bottle Holder]
8.10.6.2 Removing the Right Deck Lifter Motor0015-4992
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness [1] from the 9 wire saddles.- 10 connectors
2) Remove the motor driver PCB mounting base [3].- 4 screws [2]
F-8-703) Free the grounding wire [2].
- 1 screw [1]4) Disconnect the 9 connectors [3].5) Remove the HVT PCB [5].
- 4 screws [4]
F-8-716) Remove the 3 screws [1].
F-8-727) Remove the screw [2] while sliding the cable fixing plate [1].
[1][2][3][5]
[3][3] [4]
[1]
[2]
[1] [1]
[1][2] [2]
[2] [2][3]
[1][2][3]
[4]
[4] [5]
[2] [3][4] [4]
[1]
Chapter 8
8-35
F-8-738) Remove the right deck lifter drive assembly [3].
- 2 connectors [1]- 2 screws [2]
F-8-749) Remove the right deck lifter motor [2].
- 3 screws [1].
F-8-75
8.10.7 Right Deck Pickup Assembly
8.10.7.1 Removing the Right Deck Pickup Assembly0015-4993
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide out the right deck.2) Open the right door unit (upper).
An attempt sliding out the pickup assembly without removing the deck caus-es the lifter get trapped and may hold the pickup assembly from sliding out.
3) Disconnect the connector [3].- 1 screw [1]- 1 connector cover [2]
4) Remove the right deck pickup assembly [5].- 3 screws [4]
F-8-76
8.10.8 Left Deck Pickup Assembly
8.10.8.1 Removing the Left Deck Pickup Assembly0015-4994
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide out the left deck.2) Remove the left deck [2].
- 2 screws [1]
F-8-773) Open the front cover.4) Disconnect the connector inside of the machine [1] and reuse band [2].
F-8-785) Remove the left deck pickup assembly [3].
- 2 screws [1]- 2 pickup assembly fixing plate [2]
Keep supporting the pickup assembly; otherwise the pickup assembly maydrop when the fixing plate is removed.
[1]
[2]
[1]
[2] [3]
[1]
[2]
[3][4]
[4]
[5]
[1]
[2]
[1]
[1]
[2]
[1][2]
Chapter 8
8-36
F-8-79
8.10.9 Left Deck Pickup Motor
8.10.9.1 Before Removing the Left Deck Pickup Motor0015-4995
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the HVT PCB. (page 10-28)Reference[Removing HVT PCB]
8.10.9.2 Removing the Left Deck Pickup Motor0015-4997
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the left deck pickup motor [3].- 1 connector [1]- 2 screws [2]
F-8-80
8.10.10 Right Deck Pickup Motor
8.10.10.1 Before Removing the Right Deck Pickup Motor0015-4999
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Remove the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the main controller box cover.(page 10-17)Reference[Remov-ing the Main Controller Box Cover]
5) Remove the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
6) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
7) Remove the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-moving the Collecting Toner Bottle Holder]
8.10.10.2 Removing the Right Deck Pickup Motor0015-5004
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the right deck pickup motor [3].
- 2 screws [1]- 1 connector [2]
F-8-81
8.10.11 Left Deck Pickup Sensor
8.10.11.1 Before Removing the Left Deck Feeding Sensor0015-9411
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.11.2 Removing the Left Deck Feeding Sensor0015-9410
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the connector [1] and the 2 screws [2] from the lower side of theduplex feeding unit and remove the sensor together with its mount [3].
F-8-822) Remove the left deck feeding sensor [1].
F-8-83
8.10.12 Left Deck Pickup Solenoid
8.10.12.1 Before Removing the Left Deck Pickup Solenoid
0015-5005
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
[3]
[1]
[1][2] [1]
[1] [2]
[2]
[3]
[1][1] [2][3]
[2] [2][3]
[1]
[1]
Chapter 8
8-37
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the HVT PCB. (page 10-28)Reference[Removing HVT PCB]
8.10.12.2 Removing the Left Deck Pickup Solenoid0015-5007
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Mark the position [A] of the 2 mounting bases.2) Remove the left deck pickup drive solenoid [3] together with the mounting
base.- 1 connector [1]- 1 screw [2]
F-8-84
8.10.12.3 Adjusting the Position of the Left Deck Pickup Solenoid
0016-0029
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Before removing the left deck pickup solenoid from the support plate [1],take note of its position with reference to the fixing screw [2] of the solenoid.Or, mark the position for the solenoid by drawing a line on the support platewith a scriber.When mounting the solenoid on its own, be sure to secure it in its originalposition.
F-8-85
8.10.13 Manual Feed Pull-Out Roller Unit
8.10.13.1 Removing the Manual Feeding Pickup Roller Unit
0015-5009
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the right door unit (upper) [1], and remove the screw [2] from thedoor strap and then, fully open the right door unit (upper).
F-8-862) Slide the 2 bushings [2] and remove the manual feeding pickup roller unit
[3].
- 2 resin E-rings [1]
F-8-87
8.10.14 Manual Feed Pull-Out Roller
8.10.14.1 Before Removing the Manual Feeding Pickup Roller
0015-9388
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the manual feeding pickup roller unit. (page 8-37)Refer-ence[Removing the Manual Feeding Pickup Roller Unit]
8.10.14.2 Removing the Manual Feeding Pickup Roller0015-9389
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the 2 resin E-rings (right/left) [1].2) Remove the stopper [2], the 2 guars [3] and the 2 bushings [4].3) Remove the 2 resin E-rings [5] and the 2 bushings [6], and then remove
the manual feeding pickup roller.
When removing the stopper [2] and the guar [3], be careful not to lose thethree parallel pins [7]; they will slip off.
[1]
[2][A] [A]
[3]
[2]
[1]
[1][2]
[2]
[1]
[3]
Chapter 8
8-38
F-8-88
8.10.15 Manual Feed Roller
8.10.15.1 Before Removing the Manual Feeding Roller0015-5011
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the manual feeding pickup roller unit. (page 8-37)Refer-ence[Removing the Manual Feeding Pickup Roller Unit]
8.10.15.2 Removing the Manual Feeding Roller0015-5012
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the feeding roller [2].- 1 resin E-rings [1]
F-8-89
8.10.16 Manual Separation Roller
8.10.16.1 Before Removing the Manual Separation Roller0015-5013
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the manual feeding pickup roller unit. (page 8-37)Refer-ence[Removing the Manual Feeding Pickup Roller Unit]
8.10.16.2 Removing the Manual Separation Roller0015-5014
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the separation roller assembly [3].
- 2 resin E-rings [1]- 2 bushings [2]
F-8-902) Push the hook [1] using the driver etc. in the direction of the arrow to re-
move the separation roller [2].
F-8-91
8.10.16.3 Adjusting the Pressure of the Manual Separation Roller
0016-0026
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When picking up, if double feeding or failure occurs, adjust the position ofthe pressure spring of the separation roller.
1) Detach the right cover (upper).2) Remove the upper guide [1].
F-8-923) Move the mount [3] to adjust the position of the pressure spring of the sep-
aration roller.- If double feeding occurs, remove the mounting screw [2], lower themounting base [3] and tighten the screw [2] in the A hole. - If pickup failure occurs, remove the mounting screw [2], raise themounting base [3] and tighten the screw [2] in the B hole.
[1][3]
[7][4]
[5][6]
[5][4]
[7]
[3]
[7]
[2]
[1]
[6]
Front side
Rear side
[1][2]
[3]
[1]
[1][2]
[3]
[1]
[2]
[1]
[1]
Chapter 8
8-39
F-8-93
8.10.17 Manual Feed Tray paper sensor
8.10.17.1 Removing the Manual Feeding Tray Sensor0015-5016
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the right door unit (upper) [1], and remove the screw from the doorstrap; and then fully open the right door unit (upper).
F-8-942) Detach the cover [2].
- 1 screw [1]
F-8-953) Remove the sensor unit [2].
- 1 screw [1]
F-8-964) Free the harness [1] from the edge saddle [2], and disconnect the connec-
tor [3].5) Remove the sensor [4].
F-8-97
8.10.18 Registration Roller
8.10.18.1 Before Removing the Registration Roller0015-5017
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Remove the transfer/separation charging assembly.(page 7-30)Refer-ence[Removing Transfer/Separation Charging Assembly]
4) Remove the registration clutch.(page 8-43)Reference[Removing theRegistration Clutch]
8.10.18.2 Removing the Registration Roller0015-5020
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the protection cover [2].- 1 screw [1]
F-8-982) Remove the followings from the rear side.
- spring [1]- E-ring [2]- spacer [3]- bearing [4]- stopper [5]
[1]
[2]
hole A
hole B
[1][2]
[1] [2]
[1] [2]
[1]
[2] [3] [4]
[1]
[2]
Chapter 8
8-40
F-8-993) Remove the followings from the front side.
- Spring [1]- E-ring [2]- Spacer [3]- Bearing [4]- Stopper [5]
F-8-1004) Pull out the registration roller [1] in the direction of the arrow in the order
of [A] and [B] to remove from the machine.
F-8-101
8.10.19 Pre-Registration Roller
8.10.19.1 Before Removing the Registration Lower Roller0016-0336
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Remove the transfer/separation charging assembly.(page 7-30)Refer-ence[Removing Transfer/Separation Charging Assembly]
4) Remove the registration clutch.(page 8-43)Reference[Removing theRegistration Clutch]
5) Remove the registration brake. (page 8-43)Reference[Removing theRegistration Brake]
8.10.19.2 Removing the Registration Lower Roller0016-0337
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Pull out the pre-registration guide [1] in the direction of the arrow to re-move from the machine.
F-8-1022) Remove the pre-transfer lower guide [1].
- 1 RS tightening screw [2]- 1 holder [3]
F-8-103T-8-21
3) Remove the registration lower roller [1].- 1 spacer [2]- 3 E-rings [3]
[1]
[2]
[3]
[4][5]
[1]
[2][3]
[4][5]
[1]
[A]
[B]
[2]
When mounting the pre-registration guide, make sure the presence of the plate end [2] under the guide (front) [1] and the spring [3] on the guide (front) [1]. Also make sure the presence of the plate end [5] under the guide (rear) [4].
[1]
[1] [2][3]
[1]
[1]
[1]
[2]
[3][4]
Chapter 8
8-41
- 2 washers [4]- 2 bearings [5]
F-8-104
8.10.20 Pre-Registration Motor
8.10.20.1 Before Removing the Registration Front Motor0015-5192
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]
3) Detach the right cover (upper rear). (page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
4) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
8.10.20.2 Removing the Registration Front Motor0015-5194
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the registration front motor [3].- 1 connector [1]- 3 screws [2]
F-8-105
8.10.21 Registration Motor
8.10.21.1 Before Removing the Horizontal Registration Motor
0015-9416
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit. (page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.21.2 Removing the Horizontal Registration Motor0015-9414
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the fan together with the mount. [3]- 2 screws [1]- 1 connector [2]
F-8-1062) Free the harness from the 3 wire saddles [1].
F-8-1073) Remove the 2 screws [1].
F-8-1084) Turn the duplex feeding unit over.5) Slide the unit.
- 4 screws [1]
F-8-1096) Disconnect the connector of the duplex feeding unit in the rear side [1],
and free the harness [2] from the 2 edge saddles [3].
[1]
[2][3]
[4][5]
[3][3]
[4]
[5]
[1]
[2]
[2]
[3]
[4]
[1]
[2]
[3]
[1]
[1]
[1][1]
Chapter 8
8-42
F-8-1107) Slide the horizontal registration unit [2].
- 2 screws [1]
F-8-1118) Remove the horizontal registration motor [2].
- 2 screws [1]
F-8-112
8.10.22 Registration Sensor
8.10.22.1 Before Removing the Horizontal Registration Sensor
0015-9417
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.22.2 Removing the Horizontal Registration Sensor0015-9415
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the fan together with the mount[3].- 2 screws [1]- 1 connector [2]
F-8-1132) Free the harness from the 3 wire saddles [1].
F-8-1143) Remove the 2 screws [1].
F-8-1154) Turn the duplex feeding unit over.5) Slide the unit.
- 4 screws [1]
F-8-1166) Disconnect the connector of the duplex feeding unit in the rear side [1],
and free the harness [2] from the 2 edge saddles [3].
[1][2] [3][3]
[1]
[1] [2]
[2] [1][1]
[4]
[1]
[2]
[3]
[1]
[1]
[1][1]
Chapter 8
8-43
F-8-1177) Slide the horizontal registration unit [2].
- 2 screws [1]
F-8-1188) Remove the horizontal registration motor [2].
- 2 screws [1]
F-8-1199) Remove the horizontal registration sensor [2].
- 1 connector [1]
F-8-120
8.10.23 Registration Clutch
8.10.23.1 Before Removing the Registration Clutch0015-5195
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.23.2 Removing the Registration Clutch0015-5196
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the registration clutch [3].- 1 connector [1]- 1 E-ring [2]
F-8-121
8.10.24 Registration Brake Clutch
8.10.24.1 Before Removing the Registration Brake0016-0334
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Remove the transfer/separation charging assembly. (page 7-30)Refer-ence[Removing Transfer/Separation Charging Assembly]
4) Remove the registration clutch. (page 8-43)Reference[Removing theRegistration Clutch]
8.10.24.2 Removing the Registration Brake0016-0335
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the registration brake [1].- 1 screw [2]
F-8-122
8.10.25 Feeding Roller
8.10.25.1 Before Removing the Feeding Roller0015-5197
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the right deck pickup assembly. (page 8-35)Reference[Remov-ing the Right Deck Pickup Assembly]
2) Remove the cassette pickup assembly. (page 8-31)Reference[Removingthe Cassette 3/4 Pickup Assembly]
3) Remove the left deck pickup assembly. (page 8-35)Reference[Remov-ing the Left Deck Pickup Assembly]
8.10.25.2 Removing the Feeding Roller0015-5199
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the feeding roller cover [1].- 1 screw [2](Skip this step in for the left deck pickup assembly)
2) Remove the resin E-ring [3] in the front side of the feeding roller.3) Remove the feeding roller [5] together with the timing belt [4].
[1][2] [3][3]
[1]
[1] [2]
[2] [1][1]
[1] [2]
[1][2][3]
[1] [2]
Chapter 8
8-44
Cassette 3/4, Right deck pickup assembly
F-8-123Left deck pickup assembly
F-8-124
8.10.25.3 The Points to Mount the Feeding Roller0016-0022
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When mounting the feeding roller [1] to the cassette pickup assembly, makesure the belt pulley [2] is at the front of the machine.
Check to make sure the protrusion in the roller plate and roller are engagedsecurely.
F-8-125
8.10.26 Vertical Path Roller
8.10.26.1 Before Removing the Vertical Path Roller0015-5202
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the right deck pickup assembly. (page 8-35)Reference[Remov-ing the Right Deck Pickup Assembly]
2) Remove the cassette pickup assembly. (page 8-31)Reference[Removingthe Cassette 3/4 Pickup Assembly]
8.10.26.2 Removing the Vertical Path Roller0015-5203
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the followings from the front side of the right deck pickup assem-bly.- 1 E-ring [1]- 1 bearing [2]
2) Remove the followings from the rear side of the right deck pickup assem-bly.- 1 E-ring [3]- 2 bushings [4]- 1 roller base [5]- 1 blue guar [6]- 1 parallel screw [7]
F-8-1263) Remove the vertical path roller 1 [2]
- 1 guide plate [1]
F-8-127
8.10.26.3 Removing the Vertical Path Roller 2/30015-5204
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the followings from the front side of the cassette 3/4 pickup as-sembly.- 1 E-ring [1]- 1 spacer [2]- 1 bearing [3]
2) Remove the followings from the rear side of the cassette 3/4 pickup as-sembly.- 1 E-ring [4]- 2 bushings [5]- 1 roller base [6]- 1 blue guar [7]- 1 parallel screw [8]
3) Remove the vertical path roller 2/3 [9].
F-8-128
8.10.27 Vertical Path Motor
8.10.27.1 Before Removing the Vertical Path Upper Motor0015-5205
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing the
[1] [2] [3] [5] [4]
[3] [5] [4]
[1]
[2]
rear
front
[1]
[2]
[7][6]
[3]
[4][5]
[4]
[2]
[1]
[1]
[2][3]
[7] [8][4]
[5][6]
[9]
[5]
Chapter 8
8-45
Rear Cover (Upper)]3) Detach the rear cover (lower). (page 10-13)Reference[Removing the
Rear Cover (Lower)]4) Detach the right cover (upper rear). (page 10-12)Reference[Removing
the Right Cover (Upper Rear)]5) Detach the right cover (lower rear). (page 10-12)Reference[Removing
the Right Cover (Lower Rear)]6) Detach the main controller box cover. (page 10-17)Reference[Remov-
ing the Main Controller Box Cover]7) Remove the main controller box. (page 4-13)Reference[Removing the
Main Controller Box]8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-
moving the Collecting Toner Bottle Holder]
8.10.27.2 Removing the Vertical Path Upper Motor0015-5211
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the vertical path upper motor [3].- 2 screws [1]- 1 connector [2]
F-8-129
8.10.28 Vertical Path Duplex Motor
8.10.28.1 Before Removing the Vertical Path Duplex Motor
0015-5212
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Detach the right cover (upper rear). (page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
5) Detach the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
6) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]
7) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-moving the Collecting Toner Bottle Holder]
8.10.28.2 Removing the Vertical Path Duplex Motor0015-5217
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the vertical path duplex motor [3].- 3 screws [1]- 2 connectors [2]
F-8-130
8.10.29 Vertical Path Lower Motor
8.10.29.1 Before Removing the Vertical Path Lower Motor0015-5218
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Detach the right cover (upper rear). (page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
5) Detach the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
6) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]
7) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-moving the Collecting Toner Bottle Holder]
8.10.29.2 Removing the Vertical Path Lower Motor0015-5223
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the vertical path lower motor [3].- 3 screws [1]- 1 connector [2]
F-8-131
8.10.30 Reversing Motor
8.10.30.1 Before Removing the Reversing Motor0015-9401
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1][1] [2][3]
[1]
[2][3] [3]
[3]
[1] [2][3]
Chapter 8
8-46
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.30.2 Removing the Reversing Motor0015-9393
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the connector [1].2) Remove the reversing motor [3] together with the support plate.
- 3 screws [2]
F-8-1323) Remove the reversing motor [2] from the support plate.
- 2 screws [1]
F-8-133
8.10.30.3 Mounting the Reversing Motor0015-9394
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Mount the 2 support plates [2] and the reversing motor [3] using 3 screws[1], and then attach the timing belt [4].
F-8-134
At the end, make sure the timing belt has tension.
8.10.31 Fixing Feeding Unit Releasing Lever Sensor
8.10.31.1 Before Removing the Fixing Feeding Unit Release Lever Sensor
0015-9903
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
2) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
3) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
8.10.31.2 Removing the Fixing Feeding Unit Release Lever Sensor
0015-5226
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the wire saddle [3], and slide from the harness guide[4].- 1 connector [1]- 1 screw [2]
F-8-1352) Detach the fixing feeding unit release lever support plate [2].
- 2 screws [1]
F-8-1363) Remove the release lever switch [2].
- 1 screw [1]
F-8-137
8.10.32 Reversing Sensor
8.10.32.1 Before Removing the Reversing Sensor 10015-9403
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
[2] [3] [2]
[1][2]
[1]
[1]
[2]
[1]
[1]
[4]
[2][3]
[4] [3][1]
[2]
[1] [2]
[2]
[1]
Chapter 8
8-47
8.10.32.2 Removing the Reversing Sensor 10015-9397
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the Sensor together with the mount [3].- 2 screws [1]- 1 grounding wire [2]
F-8-1382) Remove the sensor [2].
- 1 connector [1]
F-8-139
8.10.32.3 Before Removing the Reversing Sensor 20015-9404
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.32.4 Removing the Reversing Sensor 20015-9398
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the sensor together with the mount [3].- 2 screws [1]- 1 grounding wire [2]
F-8-1402) Remove the sensor [2].
- 1 connector [1]
F-8-141
8.10.33 Reversing Unit
8.10.33.1 Before Removing the Reversing Flapper Solenoid
0015-9405
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.33.2 Removing the Reversing Flapper Solenoid0015-9391
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness [3] from the guide [2].- 1 connector [1]
2) Remove the reversing flapper solenoid [6].- 2 screws [4]- 1 grounding wire [5]
F-8-142
8.10.33.3 Mounting the Reversing Flapper Solenoid0016-0028
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Before removing the screw, make sure to mark the line in the following step.
1) Adjust the position of the solenoid using the 2 screws [1] so that the driverlever [2] is pushed fully when the solenoid is on (i.e., when the plunger isdown)
[1] [1][3]
[2]
[1] [2]
[2]
[1] [1][3]
[1] [2]
[1]
[2]
[3][5] [4] [6]
[4]
Chapter 8
8-48
F-8-143
8.10.34 Feeding Belt
8.10.34.1 Before Removing the feeding belt 0015-5227
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
5) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
6) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8.10.34.2 Removing the feeding belt 0015-5231
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the wire saddle [3], and slide the harness guide [4].- 1 connector [1]- 1 screw [2]
F-8-1442) Detach the fixing feeding unit release lever support plate [2].
- 2 screws [1]
F-8-1453) Remove the 2 screws [3].
- 1 E-ring [1]- 1 bearing [2]
F-8-1464) Remove the feeding belt unit [7].
- 1 E-ring [1]- 1 pulley [2]- 1 pin [3]- 1 screw [4]- 1 E-ring [5]- 1 bearing [6]
F-8-1475) Detach the cover [2].
- 1 screw [1]6) Remove the feeding belt [3] and the postcard belt [4].
F-8-148
[1]
[2]
[4] [3][1]
[2]
[1] [2]
[1] [3][2]
[7]
[4] [5]
[3] [2][1]
[6]
[3]
[4]
[2]
[1]
Chapter 8
8-49
8.10.35 Duplexing Unit
8.10.35.1 Before Removing the Duplex Feeding Unit0015-8267
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
8.10.35.2 Removing the Duplex Feeding Unit0015-5232
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the duplex feeding unit with holding its grip [1] (right/left) fromthe machine.
Be careful not to trap your hand between the grip and the rail. Further, do notplace the duplex unit where the parts might suffer damage.
F-8-149
8.10.36 Duplex Feed Motor
8.10.36.1 Before Removing the Duplex Feeding Left Motor
0015-9406
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.36.2 Removing the Duplex Feeding Left Motor0015-9395
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the duplex feeding left motor [3].- 1 connector [1]- 2 screws [2]
F-8-150
8.10.36.3 Before Removing the Duplex Feeding Right Motor
0015-9407
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.36.4 Removing the Duplex Feeding Right Motor0015-9396
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the duplex feeding right motor [3].- 1 connector [1]- 2 screws [2]
F-8-151
8.10.37 Duplex Feed Sensor
8.10.37.1 Before Removing the Duplex Pre-Registration Sensor
0015-9409
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover.(page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit.(page 8-49)Reference[Removing theDuplex Feeding Unit]
8.10.37.2 Removing the Duplex Pre-Registration Sensor0015-9408
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the cover [2].- 2 screws [1]
F-8-1522) Detach the sensor together with the mount [3].
- 2 screws [1]- 1 grounding wire [2]
F-8-1533) Remove the sensor [2].
- 1 connector [1]
[1]
[2][2] [3]
[1]
[1]
[2] [2][3]
[2]
[1]
[1] [1][3]
[2]
Chapter 8
8-50
F-8-154
8.10.38 Separation Roller
8.10.38.1 Before Removing the Separation Roller0015-5246
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the right deck pickup assembly. (page 8-35)Reference[Remov-ing the Right Deck Pickup Assembly]
2) Remove the cassette pickup assembly. (page 8-31)Reference[Removingthe Cassette 3/4 Pickup Assembly]
3) Remove the left deck pickup assembly. (page 8-35)Reference[Remov-ing the Left Deck Pickup Assembly]
8.10.38.2 Removing the Separation Roller0015-5248
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the open/close guide [3].- 2 mounting screws [1]- 1 feeding guide plate [2](Skip this step for the left deck pickup assembly)
F-8-1552) Remove the separation roller assembly [2] from the joint.
- 2 mounting screws [1](For the left deck, remove one screw [3])
cassette 3/4, right deck pickup assembly
F-8-156left deck pickup assembly
F-8-1573) Remove the separation roller from the separation roller [1] shaft support
mount.
cassette 3/4, right deck pickup assembly
F-8-158left deck pickup assembly
F-8-159
The urethane sponge used for this part is pink at the beginning, and changesyellow over time (accelerated if exposed to light; it may appear to change or-ange before turning pink). This is the common characteristic of urethanesponge, and does not indicate physical deterioration (performance). In addi-tion, notes that the part is not classified by color.
F-8-160
8.10.38.3 Points to Note When Mounting the Separation Roller
0016-0020
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When replacing the separation roller, be sure it is oriented as follows.
Mounting the separation roller in a wrong orientation may lead to interfer-ence against the crimping washer. Make sure it is mounted in a correct ori-entation.
Cassette 1/2, Right deck pickup assembly
F-8-161
[1] [2]
[1] [2] [3] [1]
[1] [1][2]
[3][2]
[1]
[1]
urethane sponge
Wider grooveNarrower groove
(front of machine)
(rear of machine)
Chapter 8
8-51
Left deck pickup assembly
F-8-162
8.10.38.4 Adjusting the Pressure of the Deck/Cassette Separation Roller
0016-0024
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When picking up, if double feeding or pickup failure occurs, adjust the posi-tion of the pressure spring in the separation roller.
- If double feeding occurs, move the hook of the spring in the direction ofB.- If pickup failure occurs, move the hook of the spring in the direction ofA.
F-8-163[1] Feeding roller[2] Separation roller[3] Pressure lever[4] Pressure spring
Wider groove
Narrow groove
[1]
[2]
A
B
[3]
[4]
Chapter 9 Fixing System
Contents
Contents
9.1 Construction ...................................................................................................................................................................9-19.1.1 Specifications, Control Mechanisms, and Functions ................................................................................................................... 9-19.1.2 Major Components....................................................................................................................................................................... 9-19.1.3 IH Fixing Method (outline).......................................................................................................................................................... 9-39.1.4 Limiting th Rise in Temperature at the Roller Edges by Use of a Flux blocking Plate (shutter) ................................................ 9-3
9.2 Basic Sequence ..............................................................................................................................................................9-49.2.1 Outline.......................................................................................................................................................................................... 9-49.2.2 30-Sec Start-Up Mode ................................................................................................................................................................. 9-49.2.3 Low-Temperature Environment Start-Up Mode ......................................................................................................................... 9-59.2.4 High-Humidity Environment Start-Up Mode.............................................................................................................................. 9-59.2.5 Recovery Mode............................................................................................................................................................................ 9-69.2.6 Standby Mode .............................................................................................................................................................................. 9-69.2.7 Power Save Mode ........................................................................................................................................................................ 9-79.2.8 Sleep Mode ................................................................................................................................................................................. 9-79.2.9 Copying/Printing Mode ............................................................................................................................................................... 9-79.2.10 Down Sequence ......................................................................................................................................................................... 9-89.2.11 Enhanced Fixing Mode .............................................................................................................................................................. 9-89.2.12 Heavy Paper Mode..................................................................................................................................................................... 9-99.2.13 Transparency Mode ................................................................................................................................................................... 9-99.2.14 Bond Paper Mode ...................................................................................................................................................................... 9-9
9.3 Various Control Mechanisms.......................................................................................................................................9-109.3.1 Fixing Drive System .................................................................................................................................................................. 9-10
9.3.1.1 Controlling the Drive of the Fixing Roller....................................................................................................................................................9-109.3.1.2 Controlling the Drive of the Fixing Inlet Guide............................................................................................................................................9-109.3.1.3 Controlling the Reciprocating Movement of the Thermistor........................................................................................................................9-119.3.1.4 Controlling the Reciprocating Mechanism of the Upper Separation Claw...................................................................................................9-119.3.1.5 Controlling the Drive of the Shutter..............................................................................................................................................................9-129.3.1.6 Controlling the Shutter Position....................................................................................................................................................................9-13
9.3.2 Cleaning ..................................................................................................................................................................................... 9-149.3.2.1 Controlling the Drive of the Cleaning Web ..................................................................................................................................................9-149.3.2.2 Controlling the Mechanism Used to Detect the Remaining Length of the Cleaning Web ...........................................................................9-15
9.3.3 Detecting the Passage of Paper .................................................................................................................................................. 9-169.3.3.1 Preventing Wrapping of Paper ......................................................................................................................................................................9-16
9.4 Protective Functions.....................................................................................................................................................9-179.4.1 Detecting an Error Using the Thermistor................................................................................................................................... 9-179.4.2 Detecting an Error Using the Thermal Switch........................................................................................................................... 9-179.4.3 Errors.......................................................................................................................................................................................... 9-17
9.5 Parts Replacement Procedure.......................................................................................................................................9-199.5.1 Fixing/Feeding Assembly .......................................................................................................................................................... 9-19
9.5.1.1 Before Removing the Fixing/Feeding unit....................................................................................................................................................9-199.5.1.2 Removing the Fixing/Feeding unit................................................................................................................................................................9-19
9.5.2 Fixing Unit ................................................................................................................................................................................. 9-209.5.2.1 Before Removing the Fixing Upper Unit......................................................................................................................................................9-209.5.2.2 Removing the Fixing Upper Unit..................................................................................................................................................................9-20
9.5.3 Pressure Roller ........................................................................................................................................................................... 9-209.5.3.1 Before Removing the Pressure Roller...........................................................................................................................................................9-209.5.3.2 Removing the Pressure Roller.......................................................................................................................................................................9-20
9.5.4 Upper Fixing Roller ................................................................................................................................................................... 9-219.5.4.1 Before Removing the Fixing Roller ..............................................................................................................................................................9-219.5.4.2 Removing the Fixing Roller..........................................................................................................................................................................9-219.5.4.3 Points to Note When Mounting the Fixing Roller ........................................................................................................................................9-239.5.4.4 Applying Grease After Replacing the Fixing Roller.....................................................................................................................................9-24
Contents
9.5.4.5 Adjusting the Nip Width............................................................................................................................................................................... 9-259.5.5 External Delivery Roller ............................................................................................................................................................ 9-25
9.5.5.1 Before Removing the External Delivery Roller ........................................................................................................................................... 9-259.5.5.2 Removing the External Delivery Roller ....................................................................................................................................................... 9-25
9.5.6 Internal Delivery Roller ............................................................................................................................................................. 9-269.5.6.1 Before Removing the Internal Delivery Roller............................................................................................................................................. 9-269.5.6.2 Removing the Internal Delivery Roller ........................................................................................................................................................ 9-269.5.6.3 Points to Note When Mounting the Internal Delivery Roller ....................................................................................................................... 9-27
9.5.7 Main Thermistor ........................................................................................................................................................................ 9-279.5.7.1 Before Removing the Main Thermistor/Shutter Thermistor ........................................................................................................................ 9-279.5.7.2 Removing the Main Thermistor/Shutter Thermistor .................................................................................................................................... 9-279.5.7.3 Points to Note When Mounting the Main Thermistor/Shutter Thermistor................................................................................................... 9-28
9.5.8 Sub Thermistor........................................................................................................................................................................... 9-289.5.8.1 Before Removing the Sub Thermistor .......................................................................................................................................................... 9-289.5.8.2 Removing the Sub Thermistor ...................................................................................................................................................................... 9-299.5.8.3 Points to Note When Mounting the Sub Thermistor .................................................................................................................................... 9-29
9.5.9 Thermal Switch.......................................................................................................................................................................... 9-299.5.9.1 Before Removing the Thermal Switch ......................................................................................................................................................... 9-299.5.9.2 Removing the Thermal Switch ..................................................................................................................................................................... 9-30
9.5.10 Fixing Heater ........................................................................................................................................................................... 9-309.5.10.1 Before Removing the Fixing Heater Unit................................................................................................................................................... 9-309.5.10.2 Removing the Fixing Heater Unit............................................................................................................................................................... 9-30
9.5.11 Fixing Cleaning Belt ................................................................................................................................................................ 9-329.5.11.1 Before Removing the Fixing Web .............................................................................................................................................................. 9-329.5.11.2 Removing the Fixing Web.......................................................................................................................................................................... 9-329.5.11.3 Cleaning the fixing oil dish and the fixing cleaning belt guide .................................................................................................................. 9-329.5.11.4 Mounting the Fixing Web........................................................................................................................................................................... 9-329.5.11.5 After Replacing the Fixing Web................................................................................................................................................................. 9-33
9.5.12 Fixing Jam Sensor.................................................................................................................................................................... 9-339.5.12.1 Before Removing the Delivery Jam Sensor................................................................................................................................................ 9-339.5.12.2 Removing the Delivery Jam Sensor............................................................................................................................................................ 9-33
9.5.13 Claw Jam Sensor...................................................................................................................................................................... 9-339.5.13.1 Before Removing the Claw Jam Sensor ..................................................................................................................................................... 9-339.5.13.2 Removing the Claw Jam Sensor ................................................................................................................................................................. 9-33
9.5.14 External Delivery Sensor ......................................................................................................................................................... 9-349.5.14.1 Before Removing the External Delivery Sensor......................................................................................................................................... 9-349.5.14.2 Removing the External Delivery Sensor .................................................................................................................................................... 9-34
9.5.15 Internal Delivery Sensor .......................................................................................................................................................... 9-349.5.15.1 Before Removing the Internal Delivery Sensor.......................................................................................................................................... 9-349.5.15.2 Removing the Internal Delivery Sensor...................................................................................................................................................... 9-34
9.5.16 Fixing Inlet Sensor................................................................................................................................................................... 9-349.5.16.1 Before Removing the Fixing Inlet Sensor .................................................................................................................................................. 9-349.5.16.2 Removing the Fixing Inlet Sensor .............................................................................................................................................................. 9-349.5.16.3 Adjusting the Fixing Inlet Guide ................................................................................................................................................................ 9-35
9.5.17 Fixing web sensor .................................................................................................................................................................... 9-359.5.17.1 Before Removing the Fixing Web Sensor .................................................................................................................................................. 9-359.5.17.2 Removing the Fixing Web Sensor .............................................................................................................................................................. 9-35
9.5.18 Fixing shutter sensor ................................................................................................................................................................ 9-359.5.18.1 Before Removing the Shutter Sensor.......................................................................................................................................................... 9-359.5.18.2 Removing the Shutter Sensor ..................................................................................................................................................................... 9-35
9.5.19 Fixing shutter motor................................................................................................................................................................. 9-359.5.19.1 Before Removing the Shutter Motor .......................................................................................................................................................... 9-359.5.19.2 Removing the Shutter Motor ...................................................................................................................................................................... 9-35
9.5.20 Fixing Inlet Guide Solenoid..................................................................................................................................................... 9-369.5.20.1 Before Removing the Fixing Inlet Guide Solenoid (SL1) .......................................................................................................................... 9-369.5.20.2 Removing the Fixing Inlet Guide Solenoid (SL1)...................................................................................................................................... 9-369.5.20.3 Adjusting the Fixing Inlet Guide Solenoid (SL1)....................................................................................................................................... 9-36
9.5.21 Delivery Flapper Solenoid ....................................................................................................................................................... 9-369.5.21.1 Before Removing the Delivery Flapper Solenoid (SL5) ............................................................................................................................ 9-369.5.21.2 Removing the Delivery Flapper Solenoid (SL5) ........................................................................................................................................ 9-36
Contents
9.5.21.3 Points to Note When Mounting the Delivery Flapper Solenoid (SL5) .......................................................................................................9-379.5.22 Fixing Cleaning Web Solenoid ................................................................................................................................................ 9-37
9.5.22.1 Before Removing the Fixing Web Solenoid (SL9).....................................................................................................................................9-379.5.22.2 Removing the Fixing Web Solenoid (SL9).................................................................................................................................................9-379.5.22.3 Adjusting the Fixing Web Solenoid (SL9)..................................................................................................................................................9-37
9.5.23 Upper Separation Claw ............................................................................................................................................................ 9-379.5.23.1 Removing the Upper Separation Claw........................................................................................................................................................9-379.5.23.2 Points to Note When Mounting the Upper Separation Claw ......................................................................................................................9-38
9.5.24 Lower Separation Claw............................................................................................................................................................ 9-389.5.24.1 Before Removing the Lower Separation Claw (Unit).................................................................................................................................9-389.5.24.2 Removing the Lower Separation Claw (Unit) ............................................................................................................................................9-39
Chapter 9
9-1
9.1 Construction
9.1.1 Specifications, Control Mechanisms, and Functions0015-4580
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the major functions of the machine's fixing system:T-9-1
9.1.2 Major Components0015-4581
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the major components of the machine's fixing system:
Item DescriptionFixing method IH fixingFixing heater IH heater
Fixing roller 40 mm dia., 0.65 mm thick
Pressure roller 38 mm outside dia.
Control temperature decreased gradually from 205 deg C (at standby, 17 deg C or higher)decreased gradually from 215 deg C (at standby, lower than 17 deg C)
Fixing drive control by fixing roller speed control (speed control according to paper type)
Fixing temperature detention - Main Thermistor (THM1, contact)fixing roller center; 12 mm reciprocating widthtemperature control, error detection
- Sub Thermistor (THM2, contact)fixing roller rear; no reciprocating mechanismshutter control, error detection- Shutter thermistor (THM3; contact)fixing roller rear; 12 mm reciprocating widthshutter control, error detection
Protective mechanism Executes the following error detection; in response to an error, cuts power to the fixing heater:
- thermistor temperature detention (THM1/THM2/THM3)
- thermal switch (TP1) operating temperature: 200 +/-5 deg C
Separation claw upper separation claw: contact type (3 mm reciprocating width)lower separation claw: contact type (no reciprocating mechanism)
Bias application no
Static eliminator yes; for both fixing roller and pressure roller
Cleaning mechanism oil application by webInlet guide re-configured according to paper type/length
Extra-small size support control of heating area by flux blocking plate (shutter)
Pressure release mechanism no
Chapter 9
9-2
F-9-1T-9-2
F-9-2T-9-3
[1] Fixing roller [7] Web takeup roller
[2] Pressure roller [8] Web feed roller
[3] Heater unit [9] Upper separation claw
[4] Heater assembly (coil, core) [10] Lower separation claw
[5] Fixing cleaning web [11] Fixing inlet guide
[6] Web roller [12] Static eliminator
[1] Fixing roller [5] Sub thermistor (THM2)
[2] Main thermistor (THM1) [6] Flux blocking plate (shutter)
[3] Thermal switch (TP1) [7] Shutter HP sensor (PS53)
[4] Shutter thermistor (THM3)
[1]
[2]
[3] [4]
[9]
[11][12]
[6]
[10]
[5][7] [8]
[3]
[4]
[5]
[2]
[1]
[6]
[7]
Chapter 9
9-3
9.1.3 IH Fixing Method (outline)0015-4582
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine uses the IH fixing method.
F-9-3[1] Fixing roller[2] Excitation coil[3] Core[4] Pressure roller
Note:The arrow in the figure shows the direction of paper movement.
F-9-4INV_ON: fixing heater power ON signalPWM_OUT: fixing heater power supply control signalDCON: DC controller PCBIH DRIVER: fixing heater driver PCB
MEMO: The term IH stands for "induction heating." When high-frequency current is supplied to a coil arranged inside a heater unit, a high-frequency magnetic field develops around the coil. The filed serves to permitthe flow of eddy current (induction current) to the fixing roller, causing the roller to heat on its own.
Characteristics:The use of the IH method enables the fixing roller to warm up quickly, permitting a reduction in warm-up time (30 sec) as well as of power consumption.
9.1.4 Limiting th Rise in Temperature at the Roller Edges by Use of a Flux blocking Plate (shutter)0015-4583
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When small-size paper is used, the temperature of the areas of the fixing roller surface with which the paper will not come into contact will increase (overheatingof the edges). To limit such a rise to a minimum, the machine is equipped with a flux blocking plate (shutter; made of non-magnetic material), and the fact helpsmaintain a high level of productivity when small-size paper is used.
[1]
[4]
[2]
[3]
IH DRIVER
INV_ON
PWM_OUT DCON
J1040J2402 J130
Chapter 9
9-4
F-9-5[1] Heater coil[2] Coil[3] Core[4] Shutter (The figure shows the position of the shutter for small-size paper.)[5] Fixing roller
9.2 Basic Sequence
9.2.1 Outline0015-4584
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-9-4
9.2.2 30-Sec Start-Up Mode0015-4586
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Conditions of Use>When all the following conditions exist:- the environment temperature is 17 deg C or higher.- the site is a low-humidity environment (absolute moisture content is 13 g or less)- the temperature of the fixing roller is 70 deg C or less
<Characteristics>The target temperature of the fixing roller is 205 deg C.However, the machine shifts to standby mode regardless of whether the temperature of the fixing roller reaches the target or not when 29.5 sec passes after power-on.
State Sequence DescriptionAt power-on 30-sec start-up mode When all the following conditions exist:
- the environment temperature is 17 deg C or higher- the site is a low-humidity environment- the temperature of the fixing roller is 70 deg C or lower
Low-temperature start-up mode When all the following conditions exist:- the site is a high-humidity environment- the temperature of the fixing roller is 70 deg C or lower
High humidity environment start-up mode
This mode is used when all the following conditions exist:- the site is in a high humidity environment.- the temperature of the fixing roller is 70 deg C or lower.
Recovery mode The temperature of the fixing roller is 70 deg C or higher.
In wait Standby mode To limit power consumption, the target temperature is decreased at specific time intervals after the end of start-up.
Power save mode To limit power consumption, the target temperature is decreased.
Sleep mode To limit power consumption, the target temperature is decreased at specific time intervals after the end of start-up.
In normal use Copier/printer mode To limit power consumption, the target temperature is decreased at specific time intervals after the end of start-up.
Down sequence NoneSpecial mode Fixing enhancement mode To enhance fixing, the machine changes the start-up sequence and the control temperature.
Heavy paper mode To ensure fixing on heavy paper, the machine changes the target temperature and copying/printing speed.
Transparency mode To ensure fixing on transparencies, the target temperature is increased.
Bond paper mode To ensure fixing for bond paper, machine increases the target temperature in a low-temperature environment while decreasing the copying/printing speed.
[1]
[2]
[3]
[4]
[5]
Chapter 9
9-5
F-9-6[1] Fixing roller 1/4-speed rotation[2] Fixing roller 1/1-speed rotation
9.2.3 Low-Temperature Environment Start-Up Mode0015-4587
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Conditions of Use>When all the following conditions exit:- the environment temperature is lower than 17 deg C- the temperature of the fixing roller is 70 deg C or lower
<Characteristics>- The target temperature for the fixing roller is 215 deg C.- If all the following conditions exist, the machine shifts to standby mode:
the temperature of the fixing roller has reached the target temperature.potential control has ended
- The machine takes 75 sec or less to move from power-on to standby states. (reference only)
F-9-7[1] Fixing roller 1/4-speed rotation
[2] Fixing roller 1/1-speed rotation
9.2.4 High-Humidity Environment Start-Up Mode0015-4588
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Conditions of Use>When all the following conditions exist:- the site is a high-humidity environment (absolute moisture content is 13 g or more)- the temperature of the fixing roller is 70 deg C or lower
<Characteristics>- The target temperature for the fixing roller is 205 deg C.- If all the following condition exist, the machine shifts to standby mode:
the temperature of the fixing roller has reached the target temperature.drum potential control has ended.60 sec (*1) has passed from power-on.
0
0
50
100
150
200
250
POWER ON(deg c)
(sec)
STANDBY
5 10 15 20 25 30 35 40 45 50
[1] [2]
00
50
100
150
200
180
250
POWER ON STANDBY
5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80
(deg c)
(sec)
[1] [2]
Chapter 9
9-6
F-9-8[1] Fixing roller 1/4-speed rotation
[2] Fixing roller 1/1-speed rotation
9.2.5 Recovery Mode0015-4590
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Conditions of Use>- The temperature of the fixing roller is 70 deg C or higher.
<Characteristics>- The target temperature of the fixing roller varies according to the environment temperature.
185 deg C if the environment temperature is 17 deg C or higher195 deg C if the environment temperature is lower than 17 deg C
- When the temperature of the fixing roller reaches the target temperature, the machine shifts to standby mode.- It takes 30 sec less for the machine to shift from power-on to standby states.
F-9-9[1] Fixing roller 1/4-speed rotation
[2] Fixing roller 1/1-speed rotation
9.2.6 Standby Mode0015-4592
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Characteristics>- The machine decreases the target temperature by 5 deg C at specific time intervals after a shift to standby mode (to limit power consumption).- The target temperature and the timing at which it is changed vary depending on the environment temperature (lower than or higher than 17 deg C).- The target temperature is decreased in steps and, thereafter, maintained to the following:
185 deg C if the environment temperature is less than 17 deg C180 deg C if the environment temperature is 17 deg C or higher
- If the environment temperature is lower than 17 deg C,
00
50
100
150
200
180
250
POWER ON STANDBY
5 10 15 20 25 30 35 40 45 50 55 60 65 70
(deg c)
(sec)
[1] [2]
00
50
100
150
200
250
POWER ON STANDBY
5 10 15 20 25 30
[1] [2]
(deg c)
(sec)
Chapter 9
9-7
F-9-10- If the environment temperature is 17 deg C or higher,
F-9-11
MEMO:The time that passes from a shift to standby mode is monitored continuously while a copy/print job is under way, and is used for temperature control for copying/printing. (See the descriptions under "Copying/Printing Mode.")
9.2.7 Power Save Mode0015-4593
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Characteristics>- The machine uses the appropriate target temperature for the fixing roller to suit the selected rate of power saving (in user mode).- The machine uses the appropriate target temperature for the fixing roller to suit the selected rate of power saving (in user mode).
T-9-5
9.2.8 Sleep Mode 0015-4594
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Characteristics>- The power to the fixing assembly is cut.- When the sleep mode is disabled, the machine shifts to standby mode through the start-up mode effective at time of power-on (30-sec start-up, low-temperature
environment start-up, high-humidify start-up, recovery).
9.2.9 Copying/Printing Mode0015-4596
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Characteristics>- The target temperature used while copying/printing is under way is +2 deg C in relation to the temperature used for standby.
- If the environment temperature is lower than 17 deg C
Rate of saving Standard temperature Time length to standby
-10% (default) 170 deg C 4 sec or less
-25% 160 deg C 6 sec or less
-50% 140 deg C 8 sec or less
0
210
215
200
205
190
195
180
175
185
180 360 540 720 900 10800
STANDBY(deg c)
(sec)
0
210
215
200
205
190
195
180
175
185
60 120 180 240 300 3600
STANDBY(deg c)
(sec)
Chapter 9
9-8
F-9-12[1] temperature of the fixing roller (deg C)[2] control temperature during copying
- If the environment temperature is 17 deg C or higher
F-9-13[1] temperature of the fixing roller (deg C)[2] control temperature during copying
9.2.10 Down Sequence0015-4597
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine does not have a down sequence.
9.2.11 Enhanced Fixing Mode0015-4598
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To ensure good fixing, the machine changes the control temperature between start-up sequence and standby.
<Conditions of Use>The mode (i.e., enhanced fixing mode) is selected in service mode.
<Characteristics>The machine uses different target temperatures between start-up sequence and standby mode.
T-9-6
at power-on target temperature for standby mode
start-up sequence time used (ref.)
normal mode if the temperature of the environment is 17 deg C or higher
30-sec start-up mode, or high humidity environment start-up mode
60 sec (in high humidity environment start-up mode)
See descriptions under "Standby Mode."
if the temperature of the environment is lower than 17 deg C
low temperature environment start-up mode
75 sec or less
fixing enhancement mode
if the temperature of the environment is 17 deg C or higher
high humidity environment start-up mode
60 sec normal standby mode + 10 deg C
if the temperature of the environment is lower than 17 deg C
low temperature environment start-up mode
120 sec or less same as normal mode
0
210
215
200
205
190
195
180
175
185
180 360 540 720 900 10800
[2]
[1]
STANDBY
(deg c)
(sec)
STANDBYPRINT START
0
210
215
200
205
190
195
180
175
185
60 120 180 240 300 3600
[2]
[1]
STANDBY
(deg c)
(sec)
STANDBYPRINT START
Chapter 9
9-9
SERVICE MODE:COPIER>OPTION>BODY>FSPD-S1 (Category 2)Use it to select enhanced fixing mode:0: normal (default)1: enhanced fixing mode2: not used
MEMO:If both enhanced fixing mode and heavy paper mode (or, transparency mode) are selected at the same time, heavy paper mode (transparency mode) will be givenpriority.
9.2.12 Heavy Paper Mode0015-4601
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine increases fixing temperature and changes the copying/printing speed to ensure fixing on heavy paper.
<Conditions of Use>A cassette for which heavy paper has been selected is used as the source of paper.
<Characteristics>- The target temperature differs depending on the environment temperature:
if the environment temperature is 17 deg C or higher,-> +12 deg C in relation to the target temperature.
if the environment temperature is lower than 17 deg C,-> 217 deg C.
- The machine starts to feed paper when the reading of the main thermistor becomes identical to the target temperature.- The copying/printing speed is as follows:
pickup from the cassette-> 55 cpm/ppm
pickup from the manual feeder-> 44 cpm/ppm
- If the environment temperature is lower than 17 deg C, the machine decreases the target temperature by 5 deg C every 3 min after paper feed (to as low as 192deg C).
- If the environment temperature is 17 deg C or higher, the machine decreases the target temperature by 5 deg C every 1 min after paper feed (to as low as 192 deg C).- If the environment temperature is less than 17 deg C, the machine executes idle rotation of the fixing roller for 1 min (to collect heat in the fixing assembly) before
starting copying/printing operation.- If heavy paper exists together with plain paper for output, the machine holds paper at the point of registration until the target temperature for heavy paper is reached.- If plain paper is picked up while the machine is in heavy paper mode, the machine will use the target temperature for heavy paper for fixing.
9.2.13 Transparency Mode0015-4602
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine increases the fixing temperature to ensure good fixing on transparencies.
<Conditions of Use>- The paper type is identified as being "transparency" for the manual feed tray while the tray is used as the source of paper.
<Characteristics>The target temperature of the fixing roller is 217 deg C.- The machine starts paper feed d when the reading of the main thermistor becomes identical to the target temperature.- the copying/printing speed is 44 cpm/ppm.- if the environment temperature is lower than 17 deg C, the machine starts output 1 min after the end of start-up mode (executes initial rotation for 1 min).- If a transparency exists among plain paper for output, the machine will hold the paper at the point of registration until the target temperature is reached.- If plain paper is picked up while the machine is in transparency mode, the machine will continue to use the target temperature for transparencies for fixing.
If a transparency tends to wrap around the fixing roller when the machine is in transparency mode, you can improve separation by decreasing the fixing target tem-perature for transparency mode using the following service mode item:
SERVICE MODE:COPIER>OPTION>BODY>OHP-TEMP (Category 2)0: normal (default)1: -5 deg C2: -10 deg C3: -15 deg C4: -20 deg C
9.2.14 Bond Paper Mode0015-4603
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine increases the fixing temperature while decreasing the copying/printing speed in a low-temperature environment to ensure fixing on bond paper.
<Conditions of Use>A cassette selected for bond paper is used as the source of paper.
<Characteristics>- if the environment temperature is 17 deg C or higher,
the target temperature is 205 deg C (same as normal copying/printing mode)- if the environment temperature is lower than 17 deg C,
the target temperature is 210 deg C- the copying/printing speed is 30 cpm/ppm
Chapter 9
9-10
9.3 Various Control Mechanisms
9.3.1 Fixing Drive System
9.3.1.1 Controlling the Drive of the Fixing Roller0015-4604
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the construction of the mechanisms used to control the drive of the fixing roller:
F-9-14FR_M_CLK: fixing motor clock signalFSR_M_BRAKE: fixing motor brake signalFSR_M_ON: fixing motor drive signalFSR_M_LD: fixing motor drive lock signal
[1] Fixing rollerM3: fixing motorDCON: DC controller PCBDC POWER: DC power supply PCB
ERROR CODE:E014 (fixing motor error)
0000 After the fixing motor has gone on, the machine does not detect the phase lock signal for the fixing motor for 2 sec or more.
9.3.1.2 Controlling the Drive of the Fixing Inlet Guide0015-4605
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine controls the height of the fixing inlet guide to suit the type and size of paper being in use, thus preventing the trailing edge of paper from snapping up,rubbing, or wrinkling.The following shows the mechanisms associated with the drive of the fixing inlet guide.
F-9-15FUSER_F_SL_UP: fixing inlet guide UP signal
M3
-B15
J106
-B16-B17-B18-B19-B20
GND5V
FR_M_CLK
J4005-1 24V-2 GND
FSR_M_BRAKEFSR_M_ONFSR_M_LD
[1]
DC POWER
DCON
J251
24VFUSER_F_SL_UPFUSER_F_SL_DOWN
1
91011
DCON
SL1
[1]
[2]
Chapter 9
9-11
FUSER_F_SL_DOWN:fixing inlet guide DOWN signal
[1] Fixing inlet guide[2] Fixing rollerDCON: DC controller PCBSL1: Fixing inlet guide solenoid
The following shows the position (up/down) of the fixing inlet guide controlled to suit the type/size of paper being in use:T-9-7
ERROR CODE:E841 (fixing inlet guide solenoid connection detection error)
0001 At power-on, the connection of the fixing inlet guide solenoid is not detected.
9.3.1.3 Controlling the Reciprocating Movement of the Thermistor0015-4607
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To prevent damage to the fixing roller by the main thermistor (THM1) or the shutter thermistor (THM3), the thermistor is moved in the axial direction of the fixingroller over a distance of about 12 mm.The thermistor is moved by the drive from the web drive solenoid (SL9), transmitted to the reciprocating cam by way of a one-way arm.The following shows the components associated with the mechanism used to control the thermistor reciprocating mechanism:
F-9-16[1] Fixing rollerSL9: web drive solenoidTHM1: main thermistorTHM3: shutter thermistor
9.3.1.4 Controlling the Reciprocating Mechanism of the Upper Separation Claw0015-4608
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To prevent damage to the fixing roller by the upper separation claw, the upper separation claw is moved back and forth over a distance of 3 mm in the axial directionof the fixing roller.The following shows the construction of the components used to control the upper separation claw reciprocating mechanism.
Paper type Paper length Inlet guide position
Plain paper less than 257 mm down
257 mm or more up
Heavy paper - down
SL9
[1]
(FRONT)
(REAR)
THM3
THM1
12mm
Chapter 9
9-12
F-9-17[1] Upper separation claw unit[2] Upper separation clawM3: Fixing motor
9.3.1.5 Controlling the Drive of the Shutter0015-4609
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the construction of the mechanisms used to control the drive of the shutter:
F-9-18SHUT_M_X: shutter motor drive signalHSUT_HP_SNS: shutter HP sensor signal
[1] Shutter drive gear (front)[2] Drive axis[3] Shutter[4] Shutter drive gear (rear)
DCON: DC controller PCBM15: shutter motorPS53: shutter HP sensor
The shutter is driven by the shutter motor (stepping motor), and the shutter HP sensor (PS53) is used to check to see if the shutter is set at the appropriate position.
M3
(FRONT)
(REAR)
3mm
[1]
[2]
-2
J128B-1
-3 to -6
SHUT_M_24V
SHUT_M_24V
SHUT_M_X
J251-3
J251B-8
J251-4
SHUT_HP_5V
SHUT_HP_SNS
SHUT_HP_GND
[2]
[3]
[4]
PS53
M15[1]
DCON
Chapter 9
9-13
ERROR CODE:E840 (shutter error)0001 Indicates that the HP sensor signal is not detected when the shutter is operating, after executing 3 retry operations.0002 The interval of ON-OFF detection by the sensor in response to shutter operation is shorter than a specific time period.
9.3.1.6 Controlling the Shutter Position0015-4611
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The shutter is set to the appropriate position by driving the shutter motor (stepping motor) for a specific number of steps. A cut-off is found in the periphery of theshutter gear (front) operating in conjunction with the shutter; the machine checks to see if the shutter is set to the appropriate position with reference to the outputof the shutter HP sensor (PS53), i.e., whether the sensor has detected the cut-off.
F-9-19[1] Shutter drive gear (front)[2] Cut-off (for HP detection)[3] Cut-off (for medium-size paper detection)[4] Cut-off (for small-size paper detection)PS53: shutter HP sensor
The following shows the position of the shutter (3 steps). The machine moves the shutter to the appropriate position to suit the size of the paper and the reading ofthe thermistor in question.([1] in the diagram indicates the shutter.)
- Home Position (HP)
F-9-20- Medium-Size Paper Position
F-9-21- Small-Size Paper Position
[1]
[2]
[3]
[4]
PS53
[1]
[1]
Chapter 9
9-14
F-9-22<Sequence of Shutter Operation>
- At Power-OnThe machine moves the shutter (round trip) between home position and small-size paper position to check shutter operation.
F-9-23HP : shutter position (home position)M : shutter position (medium-size paper position)S : shutter position (small-size paper position)M15 : shutter motorPS53: shutter HP sensor
- During Copying/PrintingAt time of standby, the machine sets the shutter to its home position; during copying/printing, on the other hand, the machine controls the shutter positionaccording to the selected paper size and the readings of the sub thermistor and the shutter thermistor. After copying/printing, the machine moves the shutterback to its home position.
Here, the discussion is based on shutter operation when the machine is making A5R prints in continuous mode.
F-9-24[1] When printing starts, the readings of the sub thermistor (THM2) and the shutter thermistor (THM3) are both above specific levels (THM2/THM3 >/= 203
deg C); as a result, the machine moves the shutter to small-size paper position (S).[2] The machine continues printing operation. Consequently, the readings of both thermistor are below specific levels (120 deg C </= THM2 < 150 deg C,
165 deg C </= THM3 < 195 deg C); as a result, the machine moves the shutter to home position.
MEMO:The foregoing chart has been prepared to illustrate the operation of the shutter, and the readings of the thermistor do not necessarily fluctuate as shown in the chart.
9.3.2 Cleaning
9.3.2.1 Controlling the Drive of the Cleaning Web0015-4612
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine removes toner remaining on the fixing roller by means of cleaning web (impregnated with silicone oil) to prevent fixing offset.The cleaning web is taken up by the takeup roller when the drive from the fixing web solenoid (SL9) reaches the web takeup roller drive gear by way of a one-wayclutch.
[1]
WMUP STBY
PS53
PowerON
M15
M S M HPHP
PRINT START
PSTBY
PSTBY1st Print Nth PrintN+1stPrint
N+2ndPrint
N+9thPrint
N+10thPrint
N+11thPrint
185
185
186
185
203
201
210
204
209
203
149
197
145
194
146
195
THM2
THM3(deg C)
[1] [2]
HP
M
S
Chapter 9
9-15
F-9-25[1] Cleaning web[2] Web feed roller[3] Web takeup roller[4] Web rollerSL9: web drive solenoid
The length of takeup is determined by the size of the paper used and the number of prints (within a single job).T-9-8
*1: A4/A4R/B5/B5R/A5R/LTR/LTRR*2: A3/B4/LGR/LGL
If paper exits in the fixing assembly because of a jam or error, the machine turns on the web solenoid 5 times at time of recovery (so as to prevent wrapping of thecleaning web around the fixing roller).
ERROR CODE:E005 (fixing web solenoid connection detection error)
0001 Indicates that, at time of power-on, the connection of the fixing web solenoid is not detected.
SERVICE MODE:COPIER>OPTION>BODY>CBLTINVLUse it to set the number of times the fixing web solenoid goes on.Use it if an image fault occurs as a result of soiling on the pressure roller.0: normal (default)1: twice as often as normal
9.3.2.2 Controlling the Mechanism Used to Detect the Remaining Length of the Cleaning Web0015-4614
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The remaining length of the cleaning web is detected as follows:
1) The fixing web comes wrapped around the web feed roller, and is collected by the web takeup roller as copies/prints are made.2) When the fixing web on the web feed roller decreases to a specific length, the cut-off in the web length detecting arm starts to move in the direction of the arrow,
causing the arm to block the optical path of the web length sensor (PS45). The machine will issue a fixing web length warning message on the control panel
Paper Number of web SL activations
small-size*1 1st sheet once
2nd sheet once
3rd sheet 0 times
---
Thereafter, repeated.
Large-size*2 1st sheet twice
2nd sheet once
3rd sheet once
---
Thereafter, repeated.
(FRONT)
(REAR)SL9
[1]
[2]
[3]
[4]
Chapter 9
9-16
when the fixing web solenoid goes on 4 times after the sensor has gone on.
F-9-26WEB_SENSOR: fixing web length detection signal
[1] Web length detecting arm[2] Cut-off[3] Web takeup roller
DON: DC controller PCBPS45: web length sensor
3) When copies/prints are made after the message has been issued, the machine starts to monitor the count (COPIER>COUNTER>MISC>FIX-WEB; fixing webcounter). When the count reaches '2000' (in terms of A4, 3000 copies/prints), the machine issues error code 'E005'.
SERVICE MODE:COPIER>OPTION>USER>WEB-DISPUse it to enable/disable the web length warning message:0: off (however, the message will be indicated on the service mode screen)1: on (default)COPIER>COUNTER>MISC>FIX-WEBCOPIER>COUNTER>DRBL-1>FX-WEBfixing web counter
If you have replaced the fixing web, be sure to reset the following counter readings to '0':- COPIER>COUNTER>MISC>FIX-WEB- COPIER>COUNTER>DRBL-1>FX-WEB
ERROR CODE:E005 (no web)
0000 Indicates that the absence of the fixing web is detected for 5 sec or more.
9.3.3 Detecting the Passage of Paper
9.3.3.1 Preventing Wrapping of Paper0015-4615
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To prevent warping of paper around the fixing roller, the machine will execute an emergency stop on the fixing motor if paper exits inside the fixing assembly witha delay jam at the outlet of the assembly.The presence/absence of paper inside the fixing assembly is assumed with reference to the history of detection (paper at the fixing inlet sensor, i.e., in terms ofwhether paper has moved past the senor).
J128BWEB_SENSOR_FACT_VCCWEB_SENSOR
GND
987
DCON
[1]
[3]
PS45
[2]
Chapter 9
9-17
F-9-27[1] Fixing roller[2] PaperPS51: fixing inlet sensorPS52: fixing outlet sensor
9.4 Protective Functions
9.4.1 Detecting an Error Using the Thermistor0015-4618
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
In the event of the following, the machine will set the DC power (+12 V) used to drive the AC relay (found on the fixing heater power supply PCB), thereby stoppingthe AC power to the fixing heater.
- the main thermistor (TH1)/sub thermistor (TH2)/shutter thermistor (TH3) has detected overheating.- the difference between readings of the main thermistor and the sub thermistor or between the main thermistor and the shutter thermistor has deviated from a specific
value.
9.4.2 Detecting an Error Using the Thermal Switch0015-4620
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
In response to a deviation in temperature (200 +/-5 deg C), bimetal contact of the thermal switch (TP1; non-contact type) will open to cut the power supply line(+12 VDC) used to drive the AC relay on the fixing heater power supply PCB, thereby stopping the AC power to the fixing heater.
Once open, the contact of the thermal switch will not reset itself even when the temperature drops to normal; be sure to replace the thermal switch after removingthe error.
9.4.3 Errors0015-4621
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
ERROR CODE:
E000 (low temperature detection error)0000 after power-on, the reading of the main thermistor is not 70 deg C or higher within 20 sec .0010 the power has been turned off and then on without resetting the error in question.
E001 (abnormal rise in temperature)0001 the main thermistor or the sub thermistor has been identified as being faulty, or an open circuit has been detected.0002 the reading of the main thermistor or that of the sub thermistor is 230 deg C or higher for 2 sec.0003 the reading is not 150 deg C or higher or 210 deg C or lower within 30 sec (at time of a remedial job).0010 the power has been turned off and then on without resetting of the error in question.
E002 (faulty rise in temperature)0000 the reading of the main thermistor is in excess of 70 deg C and, thereafter, it does not reach 150 deg C within 12 sec.0001 the reading of the main thermistor is in excess of 100 deg C and, thereafter, it does not reach 150 deg C within 15 sec.0010 the power has been turned off and then on without resetting of the error in question.
E003 (faulty rise in temperature)0000 the reading of the main thermistor is in excess of 100 deg C and, thereafter, is lower than 70 deg C for 2 sec or more.
[1][2]
PS52
PS51
Chapter 9
9-18
0010 the power has been turned off and then on without resetting of the error in question.
E004 (fixing heater power supply error (IH power supply))0101 there is a mismatch between the input voltage and the IH power supply ID.0102 the fault IH current is faulty (current leakage).0103 the IH current is faulty (absence of current).0104 there is overcurrent.0201 when the power is turned on (or while the IH drive is suspended), the IH control mechanisms is not in an initial state.0202 at time of IH start-up, the IH control enable flag is not set within 1 sec after the start flag has been set.0203 when IH is stored, the IH control ongoing flag is not released within 1 sec.0204 the 12-V power supply (IH relay) is identified as being OFF.0205 at IH start-up, the PWM ON signal data has an error.
If E000 through E004 is indicated, the error code will not be reset even when you turn off the main power switch, requiring you to use service mode (COPIER >FUNCTION > CLEAR > ERR).
Chapter 9
9-19
9.5 Parts Replacement Procedure
9.5.1 Fixing/Feeding Assembly
9.5.1.1 Before Removing the Fixing/Feeding unit0015-8187
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
9.5.1.2 Removing the Fixing/Feeding unit0015-5039
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) While pushing the hook shaft [1] found at the rear of the fixing/feedingunit in the direction of the arrow (toward the machine front), rotate thefixing/feeding unit release lever clockwise to lock it in place [2].
F-9-282) While pushing the 2 stopper plates [1] of the rail assembly of the fixing/
feeding unit to the inside and slide out the fixing/feeding unit [2].
F-9-29
Follow the steps above when sliding out the fixing/feeding unit.Follow the steps below when detaching the fixing/feeding unit from the ma-chine.
3) Remove the fixing/feeding unit [2] from the rail.- 2 screws [1]
[2]
[1]
[2]
[1]
[1]
Chapter 9
9-20
F-9-30
9.5.2 Fixing Unit
9.5.2.1 Before Removing the Fixing Upper Unit0015-8190
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
9.5.2.2 Removing the Fixing Upper Unit0015-5042
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Release the 3 harness guide locks [1] to free the harness from the guidesand disconnect 6 connectors [2].
F-9-31
Be sure to disconnect the shutter HP sensor connector. If left connected whenremoving the fixing upper unit, the shutter mount plate may be deformed orthe connector may be damaged.ÅB
2) Remove the fixing upper unit [2] in the direction of the arrow.- 2 screws [1]
F-9-32
9.5.3 Pressure Roller
9.5.3.1 Before Removing the Pressure Roller0015-7178
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9) Remove the lower separation claw unit. (page 9-39)Reference[Remov-ing the Lower Separation Claw (Unit)]
9.5.3.2 Removing the Pressure Roller0015-5045
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[2]
[1]
[1]
[1]
[1]
[2]
[2]
[2][2]
[1]
Chapter 9
9-21
1) Remove the pressure roller assembly [1]. Place the removed pressure roll-er assembly temporarily on the paper.
F-9-332) Remove the pressure roller assembly.
- 2 E-rings at the both end [1]- 2 bearings [2]
F-9-34
As aged, the rubber surface of the pressure roller may be discolored by heat.This change, however, will not affect its performance or output images. Fur-ther, the physical properties of the roller may develop wrinkles on the rollersurface. The wrinkles will be smoothed under heat and not affect the per-formance, so that the replacement is not required.
9.5.4 Upper Fixing Roller
9.5.4.1 Before Removing the Fixing Roller0015-7188
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9) Remove the fixing web. (page 9-32)Reference[Removing the FixingWeb]
9.5.4.2 Removing the Fixing Roller0015-5047
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove 1 screw [1] and the pin [2]. The screw and pin removed here willbe used in the step 6).
F-9-352) Rotate the shutter drive gear [1] by finger so that the shutter gear [2] ro-
tates until the cut-off [3] of the shutter gear matches the hole in the plate[4].
F-9-363) Fit the pin removed in the step 1) into the hole [2], then fix with 1 screw
[3] in place.
F-9-37
The pin should be fit back in the initial position after completing the forego-ing steps and before mounting the fixing upper unit on the machine.
4) Remove 2 screws [2] that fix the AC connector support plate [1].
[1]
[1]
[2]
[1]
[2]
[1]
[2]
[3]
[4]
[1][2][4]
[1] [2][3]
Chapter 9
9-22
F-9-385) Turn the fixing upper unit upside down.6) Remove the shutter drive gear shaft support plate [2].
- 1 screw [1]
F-9-397) Slide out the heater unit [2] to remove.
- 2 screws [1]
F-9-40
- The shutter is thin (0.5mm in thickness) and can be easily deformed.Once deformed, it may damage the roller surface by interference. Caresmust be taken not to deform the shutter during the work.- As aged, the shutter surface may be discolored by heat or damaged dueto friction. This, however, will not affect the performance.
8) Remove the core positioning plate (front) [2].- 2 screws [1]
F-9-419) Remove 1 screw [1] and the pin [2]. The screw and pin removed here will
be used in the step 11).
F-9-4210) Rotate the shutter drive gear [1] by finger so that the cut-off [2] of the
shutter gear matches to the hole in the plate [3].
F-9-4311) Fit the pin [1] removed in the step 9) in the hole [2], then fix with 1 screw
[3] in place.
[1][2] [2]
[1] [2]
[1] [1][2]
[1] [1][2]
[1] [2]
[1][3]
[1][2][3]
Chapter 9
9-23
F-9-44
The pin should be fit back in the initial position after completing the forego-ing steps and before mounting the fixing upper unit on the machine.
12) Release 2 hooks [1] that fix the bearings at the both end of the fixing roll-er to remove the fixing roller assembly [2].
F-9-45
- When replacing gear/bushing/bearing only (that is, the fixing roller notto be replaced), wrap paper around the roller before starting thereplacement. This is to prevent any possible damage to the roller surfacein such event that the bearing is fallen on it during the work.- The removed roller should be placed on paper temporarily during thework.
F-9-46
13) Remove 2 C-rings [1], 2 gears [2], 2 bushings [3] and 2 bearings fromthe fixing roller assembly.
F-9-47
As aged, the fixing roller surface may be discolored by heat. This, however,will not affect the performance. The fixing roller surface color is differentdepending on the vendors but any rollers meet the specified performance.
9.5.4.3 Points to Note When Mounting the Fixing Roller0015-5049
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- A new fixing roller is wrapped in paper. The paper should not beremoved until the fixing roller is placed in the specified position in thefixing upper unit and the bearings at the both ends are fixed with hooks.This is to prevent any possible damage to the roller surface in such eventthat the bearing is fallen on the fixing roller.- Pay attention to the orientation of the bearings [1] and the bushings [2].Be sure that the grooved side of bearing faces inside and the collar of thebushing faces outside. Also the rear and front fixing gears shapedifferently; mount the gear [3] (w/ larger protrusion) rear and the gear [4](w/ smaller protrusion) front.
F-9-48- When fixing the C-ring [1], be sure to hook the 2 ends of the C-ring [1]on the protruded parts of the fitting gear and fit the 3 protrusions of the C-ring [2] properly into the grooves on the fixing roller.
F-9-49- When mounting the fixing roller, cares should be taken not to hit thethermal switch with the fixing roller.- After mounting the fixing roller, make sure that the main thermistor [1],the shutter thermistor [2] and the sub thermistor [3] are parallel andcontact with the fixing roller.
[1] [2][3]
[2]
[1]
[1]
[1][2]
[3]
[4]
[1][2]
[3][4]
[1] [2][3] [4]
[1]
[2]
Chapter 9
9-24
F-9-50
F-9-51- When fixing the core positioning plate [1] (both front and rear sides)with screws [2] after mounting the fixing roller, tighten the screws whilepushing the bearing [3] of the fixing roller downward with finger. This isto eliminate the gap [A] between the bearing and the fixing frame. Thiswork should be properly done, or the gap in the joint is likely to cause thefixing fault or paper wrinkles.
F-9-52
F-9-53- Be sure to remove the paper around the roller after mounting the fixingroller to the fixing unit.- Be sure to fit the 2 pins [1] back to the initial positions. If this is undonewhen turning the main power switch on, ‘E840’ error will be returned. Ifturning on the main power switch with the only one pin fit, this will causenot only the ‘E840’ error but also the shutter distortion.
F-9-54
9.5.4.4 Applying Grease After Replacing the Fixing Roller0015-9975
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- About 20mg of grease (Molykote HP-300; CK-8012) should be appliedto the inner [1] and the outer surfaces [2] of the bushing until the whitecoat covering is formed uniformly. If this undone, the noise (squeaking)may occur.
[1][2]
[3]
[2] [2]
[2] [2]
[1]
[1]
[3]
[3] [3][A]
[1]
[1]
Chapter 9
9-25
F-9-55- Applied grease may be transferred from the bushing to the fixing rollerends [1] when mounting; be sure to wipe it off when this happens.
F-9-56
9.5.4.5 Adjusting the Nip Width0015-9977
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The nip width adjustment is not necessary.
9.5.5 External Delivery Roller
9.5.5.1 Before Removing the External Delivery Roller0015-7190
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Detach the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
9.5.5.2 Removing the External Delivery Roller0015-5052
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the delivery roller guide [2].- 2 screws [1]
F-9-572) Remove the bushing [2] and the delivery unit [3].
- 1 screw [1]
F-9-58
When putting the removed delivery unit aside temporarily, place the unit tothe orientation as shown in the figure below. The separation claw may bedamaged if the claw hit against the floor.
F-9-59
3) Remove the external delivery roller [9].- 1 E-ring [1]- 1 O-ring [4]- 1 bushing [3](at the front)- 1 E-ring [4]- 1 gear [5]- 1 E-ring [6]- 1 O-ring [7]- 1 bushing [8](at the rear)
[2][1]
[1]
[1]
[2]
[1]
[2][3]
Chapter 9
9-26
F-9-60
9.5.6 Internal Delivery Roller
9.5.6.1 Before Removing the Internal Delivery Roller0015-7187
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Detach the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9) Remove the lower separation claw unit. (page 9-39)Reference[Remov-ing the Lower Separation Claw (Unit)]
9.5.6.2 Removing the Internal Delivery Roller0015-5053
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide the fixing heat discharge fan assembly [3] toward the outside.- 3 connectors [1]- 3 screws [2]
F-9-612) Shift the gear [2].
- 1 E-ring [1]
F-9-623) Remove the gear [2].
- 1 E-ring [1]
F-9-63The following steps 4) and 5) are performed at the rear side.
4) Remove 1 connector [3] found inside of the delivery motor [2].- 4 screws [1]
Be careful not the bearing and the O-ring fallen off.
[1][2]
[3]
[4] [5]
[6][7]
[8]
[9]
[1] [1][2] [3]
[3]
[4]
[1][2]
[1][2]
Chapter 9
9-27
F-9-64
F-9-655) Shift the connector support plate [2] toward the outside.
- 2 screws [1]
F-9-666) Remove the internal delivery roller [3].
- 2 E-rings [1]- 2 bearings [2]
F-9-67
9.5.6.3 Points to Note When Mounting the Internal Delivery Roller
0015-5054
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
A harness is found near the end of the internal delivery roller shaft (at the rearside) and 2 plastic sheets [1] are attached to protect the harness. Whenmounting/removing the internal delivery roller, be careful not to removethese plastic sheets by accident. If removed accidentally, reattach the sheetsback to the initial positions.
F-9-68
9.5.7 Main Thermistor
9.5.7.1 Before Removing the Main Thermistor/Shutter Thermistor
0015-7186
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9) Remove the fixing web. (page 9-32)Reference[Removing the FixingWeb]
9.5.7.2 Removing the Main Thermistor/Shutter Thermistor
0015-5055
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the bushing [2], and then remove the web unit [3].- 1 screw [1]
[1][1] [2]
[3]
[1] [2]
[1]
[1][2]
[1]
[2]
[3]
[1]
[2]
Chapter 9
9-28
F-9-692) Remove the silicone oil tray [2].
- 1 screw [1]
F-9-703) Detach the harness retaining cover [2].
- 1 screw [1]
F-9-714) Free the harness from the harness guide assembly [1].
F-9-725) Shift the thermistor mounting shaft [2] to detach it from the bushing.
- 2 screws [1]- 1 reuse band [3]
F-9-73
6) Remove the 2 leaf springs each [1] to remove the main thermistor [2] andthe shutter thermistor [3].
F-9-74
9.5.7.3 Points to Note When Mounting the Main Thermistor/Shutter Thermistor
0015-5056
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- Route the harness of the thermistor as shown below. The harness [1]should route via the outside (the rear side) of the guide pin [2].
F-9-75- After mounting, make sure the main thermistor [1] and the shutterthermistor [2] are parallel and contact with the fixing roller. If not, restartthe mounting steps
F-9-76
9.5.8 Sub Thermistor
9.5.8.1 Before Removing the Sub Thermistor0015-7192
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-
[1]
[2]
[3]
[1] [2]
[1][2]
[1]
[1]
[2][3]
[1] [1][2] [1] [1][3]
[1] [2]
[1][2]
Chapter 9
9-29
moving the Fixing/Feeding Unit Front Cover]5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-
ence[Removing the Fixing/Feeding Unit Middle Cover]6) Detach the fixing upper cover. (page 10-15)Reference[Removing the
Fixing Upper Cover]7) Remove the fixing drive assembly. (page 10-22)Reference[Removing
the Fixing Drive Assembly]8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-
ing Upper Unit]9) Remove the fixing web. (page 9-32)Reference[Removing the Fixing
Web]
9.5.8.2 Removing the Sub Thermistor0015-5057
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the bushing [2], and then remove the web unit [3].- 1 screw [1]
F-9-772) Remove the silicone oil tray [2].
- 1 screw [1]
F-9-783) Detach the harness retaining cover [2].
- 1 screw [1]
F-9-794) Free the harness from the harness guide assembly [1].
F-9-80
5) Remove the sub thermistor assembly [2].- 1 screw [1]
F-9-816) Remove the sub thermistor [2].
- 1 screw [1]
F-9-82
9.5.8.3 Points to Note When Mounting the Sub Thermistor
0015-5058
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- After mounting, make sure that the sub thermistor [1] is parallel andcontacts with the fixing roller. If not, restart the mounting steps.
F-9-83
9.5.9 Thermal Switch
9.5.9.1 Before Removing the Thermal Switch0015-7193
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing the
[1]
[2]
[3]
[1] [2]
[1][2]
[1]
[1] [2]
[1][2]
[1]
Chapter 9
9-30
Fixing Upper Cover]7) Remove the fixing drive assembly. (page 10-22)Reference[Removing
the Fixing Drive Assembly]8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-
ing Upper Unit]9) Remove the main thermistor/shutter thermistor assembly. (page 9-
27)Reference[Removing the Main Thermistor/Shutter Thermistor]
9.5.9.2 Removing the Thermal Switch0015-5059
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness of the thermal switch from the harness guide.
F-9-842) Remove the thermal switch [2]. (Remove the harness of the thermal
switch [3] by leading it through the opening as shown in the figure below[A].)- 1 screw [1]
F-9-85
9.5.10 Fixing Heater
9.5.10.1 Before Removing the Fixing Heater Unit0015-7174
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9.5.10.2 Removing the Fixing Heater Unit0015-5060
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove 1 screw [1] and the pin [2]. The screw and pin removed here willbe used in the step 4) below.
F-9-862) Rotate the shutter gear [2] by rotating the shutter drive gear [1] with finger
until the cut-off of the shutter gear [3] matches to the hole in the plate [4].
F-9-873) Fit the pin [1] (the one removed in the step 2)) in the hole [2] and fix it
with the 1 screw [3].
F-9-88
After completing the works in these steps, fit the pin back to the initial posi-tion.
4) Remove the 2 screws [2] that fix the AC connector support plate [1].
[1]
[1] [2]
[A]
[3]
[1]
[2]
[1]
[2]
[3]
[4]
[1][2][4]
[1] [2][3]
Chapter 9
9-31
F-9-895) Turn the fixing upper unit upside down.6) Remove the shutter drive gear shaft support plate [2].
- 1 screw [1]
F-9-907) Slide out the heater unit [2] to detach.
- 2 screws [1]
F-9-918) Free the AC harness [1] from the harness guide [2].
F-9-929) Remove the 2 screws [1] to free the AC harness from the clamp and re-
move the AC inlet [2].
F-9-9310) Remove the fixing heater unit stopper plate [2].
- 1 screw [1]
F-9-94
The 2 screws shown in the figure (glued in place) should not be loosened orremoved.
F-9-95
11) Remove the fixing heater unit [2] in the direction of the arrow.- the shutter [1]
F-9-96
The shutter is thin (0.5mm in thickness) and may be easily deformed. Oncedeformed, the fixing roller surface can be damaged by interference. Caresshould be taken during the work not to deform the shutter.
MEMO:As aged, the shutter surface may be discolored by heat or damaged by fric-tion, however, this will not affect the performance.
[1][2] [2]
[1] [2]
[1] [1][2]
[1]
[2]
[1]
[2]
[1]
[2]
[1]
[1]
[2]
Chapter 9
9-32
9.5.11 Fixing Cleaning Belt
9.5.11.1 Before Removing the Fixing Web0015-8279
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
9.5.11.2 Removing the Fixing Web0015-5061
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the web unit [2].- 2 screws [1]
F-9-972) While pushing the web feed roller [1] and the web take-up roller [2] to-
ward the rear side, detach the fixing web [3].
F-9-98
9.5.11.3 Cleaning the fixing oil dish and the fixing cleaning belt guide
0016-0087
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing web.2) Clean the surface of the silicone oil tray [1].3) Clean the surface of the fixing cleaning web guide [2].
F-9-99
9.5.11.4 Mounting the Fixing Web0015-5062
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Reverse the removal steps above and follow them to mount the fixing web.
1) Wind the web [2] around the web take-up roller [1] for 2 to 3 times. Makesure the arm guide plate [3] facing the outside of the web take-up rollerwhen mounting. Also make sure the oil impregnated in the contact areaof the roller.
F-9-100
When winding the web, make sure the fixing web not skewed or free fromslack [A] or wrinkles.
F-9-101Follow the orientation shown in the figure below when winding and mount-ing the fixing web.
[2]
[1]
[1][2]
[3]
[1]
[2]
[3] [1]
[2]
[A]
Chapter 9
9-33
F-9-102
2) After fitting the fixing web, move the plunger [1] of the web guide sole-noid in the direction of the arrow until the fixing web is free of the slack.
F-9-103
9.5.11.5 After Replacing the Fixing Web0015-9981
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
After replacing the fixing web, be sure to reset the counter reading to ‘0’ byusing the following service mode items.COPIER> COUNTER> MISC> FIX-WEBCOPIER> COUNTER> DRBL-1> FX-WEB
9.5.12 Fixing Jam Sensor
9.5.12.1 Before Removing the Delivery Jam Sensor0015-7176
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Detach the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Remove the external delivery roller. (page 9-25)Reference[Removingthe External Delivery Roller]
9.5.12.2 Removing the Delivery Jam Sensor0015-5064
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide out the sensor support plate.- 2 screws [1]
F-9-1042) Remove the delivery jam sensor [2] from the sensor support plate.
- 1 connector [1]
F-9-105
9.5.13 Claw Jam Sensor
9.5.13.1 Before Removing the Claw Jam Sensor0015-7195
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9) Remove the lower separation claw unit. (page 9-39)Reference[Remov-ing the Lower Separation Claw (Unit)]
10) Remove the internal delivery roller. (page 9-26)Reference[Removingthe Internal Delivery Roller]
9.5.13.2 Removing the Claw Jam Sensor0015-5065
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the protrusion [2] to slide out the sensor support plate [3].- 1 screw [1]
F-9-1062) Remove the claw jam sensor [2] from the sensor support plate.
- 1 connector [1
F-9-107
Take-up roller
Feed roller
[1]
[1]
[2]
[2] [1]
[1] [2][3]
[1][2]
Chapter 9
9-34
9.5.14 External Delivery Sensor
9.5.14.1 Before Removing the External Delivery Sensor0015-7196
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Remove the external delivery roller. (page 9-25)Reference[Removingthe External Delivery Roller]
9.5.14.2 Removing the External Delivery Sensor0015-5066
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide out the sensor support plate.- 2 screws [1]
F-9-1082) Remove the external delivery jam sensor [2] from the sensor support plate.
- 1 connector [1]
F-9-109
9.5.15 Internal Delivery Sensor
9.5.15.1 Before Removing the Internal Delivery Sensor0015-7198
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9) Remove the lower separation claw unit. (page 9-39)Reference[Remov-ing the Lower Separation Claw (Unit)]
10) Remove the internal delivery roller. (page 9-26)Reference[Removingthe Internal Delivery Roller]
9.5.15.2 Removing the Internal Delivery Sensor0015-5067
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the protrusion [2] to slide out the sensor support plate [3].- 1 screw [1]
F-9-1102) Remove the internal delivery sensor [2] from the sensor support plate.
- 1 connector [1]
F-9-111
9.5.16 Fixing Inlet Sensor
9.5.16.1 Before Removing the Fixing Inlet Sensor0015-8346
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
9.5.16.2 Removing the Fixing Inlet Sensor0015-5068
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Check the positions (front, rear) of the fixing inlet guide base (the relativepositions between the marking line of the fixing inlet guide base and theindexes of the height adjusting support plate). Then remove the 2 screws[3] and the 1 connector [4] and remove the fixing inlet guide base [5].
F-9-1122) Remove the fixing inlet sensor [1] from the fixing inlet guide plate.
[1]
[2]
[2][1]
[1] [2][3]
[1] [2]
[1] [1]
[2][2]
[3] [3][4][5]
Chapter 9
9-35
F-9-113
When mounting the fixing inlet guide base, be sure to mount it in the correctposition as checked in the step 1).
9.5.16.3 Adjusting the Fixing Inlet Guide0015-5069
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the solenoid position with the screw [1] so that the fixing inlet guidepositions as indicated in the figure below when the solenoid is turned on.
F-9-114<Points to Note When Adjusting in the Field>
- The fixing inlet guide is at the lower position when the solenoid (SL1)is turned on.- The heights at the front and rear sides of the fixing inlet guide should beadjusted within 0.2mm difference.- Adjust the height of the fixing inlet guide by loosening the fixing screwon the height adjusting support plate.
9.5.17 Fixing web sensor
9.5.17.1 Before Removing the Fixing Web Sensor0015-8280
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
2) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
9.5.17.2 Removing the Fixing Web Sensor0015-5070
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the fixing web sensor [2].- 1 connector [1]
F-9-115
9.5.18 Fixing shutter sensor
9.5.18.1 Before Removing the Shutter Sensor0015-7199
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing theFixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-ing Upper Unit]
9.5.18.2 Removing the Shutter Sensor0015-5071
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the shutter sensor support plate [2].- 1 screw [1]
F-9-1162) Remove the shutter sensor [1] from the shutter sensor support plate.
F-9-117
9.5.19 Fixing shutter motor
9.5.19.1 Before Removing the Shutter Motor0015-8281
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
2) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
9.5.19.2 Removing the Shutter Motor0015-5072
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the harness guide [1] and remove the shutter motor[4].- 1 connector [2]- 2 screws [3]
[1]
1.6m
m
Fixing roller
Pressure roller
Solenoid
Inlet guide
11.1
mm
12.7
mm
[1]
[1][2]
[1][2]
[1]
Chapter 9
9-36
F-9-118
9.5.20 Fixing Inlet Guide Solenoid
9.5.20.1 Before Removing the Fixing Inlet Guide Solenoid (SL1)
0015-8282
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
2) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
3) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
9.5.20.2 Removing the Fixing Inlet Guide Solenoid (SL1)0015-5073
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the wire saddle [3] and remove the harness guide.- 1 connector [1]- 1 screw [2]
F-9-1192) Remove the fixing/feeding unit releasing lever support plate [2].
- 2 screws [1]
F-9-120
Mark the screw positions before removing the screws in the next step.
3) Remove the fixing inlet guide solenoid [2].- 2 screws [1]
F-9-121
9.5.20.3 Adjusting the Fixing Inlet Guide Solenoid (SL1)0015-9983
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the position of the fixing inlet guide solenoid with the screw [1] sothat the guide positions as shown in the figure below when the solenoid isturned on.
F-9-122
9.5.21 Delivery Flapper Solenoid
9.5.21.1 Before Removing the Delivery Flapper Solenoid (SL5)
0015-7200
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Detach the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Remove the external delivery roller. (page 9-25)Reference[Removingthe External Delivery Roller]
4) Remove the sensor support plate (the external delivery sensor/the deliveryjam sensor). (page 9-33)Reference[Removing the Delivery Jam Sen-sor]
9.5.21.2 Removing the Delivery Flapper Solenoid (SL5)0015-5075
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the wire saddle [4] and slide the delivery flapper so-lenoid [3] to the side to remove.- 1 connector [1]- 2 screws [2]
[1]
[2]
[3]
[4]
[3][1]
[2]
[1] [2]
[2][1]
1.6m
m
Fixing roller
Pressure roller
Solenoid
Inlet guide
11.1
mm
12.7
mm
[1]
Chapter 9
9-37
F-9-123
9.5.21.3 Points to Note When Mounting the Delivery Flapper Solenoid (SL5)
0015-5076
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When mounting the delivery flapper solenoid, be sure that the delivery flap-per solenoid arm [1] and the sensor arm [2] position at the correct relativepositions.
F-9-124
9.5.22 Fixing Cleaning Web Solenoid
9.5.22.1 Before Removing the Fixing Web Solenoid (SL9)0015-8303
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
2) Remove the fixing drive assembly. (page 10-22)Reference[Removingthe Fixing Drive Assembly]
9.5.22.2 Removing the Fixing Web Solenoid (SL9)0015-5077
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Mark the screw positions before removing the screws in the next step.
1) Remove the fixing web solenoid [3].- 1 connector [1]- 2 screws [2]
F-9-125
9.5.22.3 Adjusting the Fixing Web Solenoid (SL9)0015-9979
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
a. For New Fixing WebsAdjust the solenoid position with the screw [2] so that the drive lever [1]can shift up to 8.6mm.
F-9-126
b. For Used Fixing WebsBefore removing the solenoid, check the position (A) of the drive lever[1] when the solenoid is turned on. After replacing the solenoid, adjust thedrive lever [1] position with the screw [2] so that it positions as it didbefore replacement.
F-9-127
9.5.23 Upper Separation Claw
9.5.23.1 Removing the Upper Separation Claw0015-5079
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover [1].
[1] [4][2]
[3] [2][1] [3]
8.6mm
[1]
[2]
A
[1]
[2]
Chapter 9
9-38
F-9-1282) Turn the fixing/feeding unit releasing lever [1] counterclockwise to un-
lock. Hold the lever [1] to slide out the fixing/feeding unit [2] forward.(Note that the duplexing feed unit will also be slid out.)
F-9-1293) Open the delivery unit cover [1].
F-9-1304) While lifting the spring [1], remove the upper separation claw [2].
F-9-131
9.5.23.2 Points to Note When Mounting the Upper Separation Claw
0015-5080
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Pay attention to the relative positions between the upper separation claw andspring when mounting the upper separation claw.
F-9-132
9.5.24 Lower Separation Claw
9.5.24.1 Before Removing the Lower Separation Claw (Unit)
0015-7204
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing theFixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page 10-15)Refer-ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing the
[1]
[1] [2]
[1]
[1] [2]
Chapter 9
9-39
Fixing Upper Cover]7) Remove the fixing drive assembly. (page 10-22)Reference[Removing
the Fixing Drive Assembly]8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-
ing Upper Unit]
9.5.24.2 Removing the Lower Separation Claw (Unit)0015-5082
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the 4 clamps and disconnect the 1 connector [1].
F-9-1332) Remove the lower separation claw unit [2].
- 2 screws [1]
F-9-134
When removing the lower separation claw unit, follow the steps above.Follow the steps below when removing the lower separation claw.
3) Remove the 2 springs [1] from the lower separation claw.
F-9-1354) Remove the lower separation claw support plate [2] and remove the lower
separation claw [3].- 3 screws [1]
F-9-136
[1]
[2]
[1]
[1]
[1]
[2]
[3]
Chapter 10 External and Controls
Contents
Contents
10.1 Control Panel..............................................................................................................................................................10-110.1.1 Overview.................................................................................................................................................................................. 10-110.1.2 LCD Indication Processing ...................................................................................................................................................... 10-110.1.3 Adjusting the LCD Contrast .................................................................................................................................................... 10-110.1.4 Functions of the Control Panel CPU........................................................................................................................................ 10-1
10.2 Counters .....................................................................................................................................................................10-110.2.1 Soft Counters ........................................................................................................................................................................... 10-1
10.3 Fans ............................................................................................................................................................................10-310.3.1 Arrangement, Functions, and Error Codes .............................................................................................................................. 10-310.3.2 Controlling the Speed of the Fans............................................................................................................................................ 10-410.3.3 Sequence of Operation ............................................................................................................................................................. 10-4
10.4 Power Supply System ................................................................................................................................................10-510.4.1 Power Supply ........................................................................................................................................................................... 10-5
10.4.1.1 Overview .....................................................................................................................................................................................................10-510.4.1.2 Distribution of Power and the Switches......................................................................................................................................................10-5
10.4.2 Rated Output of the DC Power Supply PCB ........................................................................................................................... 10-710.4.2.1 Rated Output of the DC Power Supply PCB ..............................................................................................................................................10-710.4.2.2 Rated Output of the Accessories Power Supply PCB.................................................................................................................................10-7
10.4.3 Protection Function .................................................................................................................................................................. 10-810.4.3.1 Protective Functions....................................................................................................................................................................................10-8
10.4.4 Backup Battery......................................................................................................................................................................... 10-810.4.4.1 Backup Battery............................................................................................................................................................................................10-8
10.4.5 Energy-Saving Function .......................................................................................................................................................... 10-810.4.5.1 Overview .....................................................................................................................................................................................................10-810.4.5.2 SNMP setup ................................................................................................................................................................................................10-9
10.5 Parts Replacement Procedure...................................................................................................................................10-1210.5.1 External Covers...................................................................................................................................................................... 10-12
10.5.1.1 Right Cover (Lower Rear) ........................................................................................................................................................................10-1210.5.1.1.1 Removing the Right Cover (Lower Rear) .........................................................................................................................................10-12
10.5.1.2 Right Cover (Upper Rear) .........................................................................................................................................................................10-1210.5.1.2.1 Removing the Right Cover (Upper Rear) .........................................................................................................................................10-12
10.5.1.3 Right Cover (Upper) .................................................................................................................................................................................10-1210.5.1.3.1 Removing the Right Cover (Upper) ..................................................................................................................................................10-12
10.5.1.4 Left Cover (Upper)....................................................................................................................................................................................10-1210.5.1.4.1 Removing the Left Cover (Upper) ....................................................................................................................................................10-12
10.5.1.5 Front Cover ...............................................................................................................................................................................................10-1310.5.1.5.1 Removing the Front Cover................................................................................................................................................................10-13
10.5.1.6 Rear Cover (Upper)...................................................................................................................................................................................10-1310.5.1.6.1 Removing the Rear Cover (Upper) ...................................................................................................................................................10-13
10.5.1.7 Rear Cover (Lower) ..................................................................................................................................................................................10-1310.5.1.7.1 Before Removing the Rear Cover (Lower) .......................................................................................................................................10-1310.5.1.7.2 Removing the Rear Cover (Lower)...................................................................................................................................................10-13
10.5.1.8 Left Cover (Lower) ...................................................................................................................................................................................10-1310.5.1.8.1 Before Removing the Left Cover (Lower)........................................................................................................................................10-1310.5.1.8.2 Removing the Left Cover (Lower)....................................................................................................................................................10-13
10.5.1.9 Left Cover (Middle) ..................................................................................................................................................................................10-1410.5.1.9.1 Removing the Left Cover (Middle)...................................................................................................................................................10-14
10.5.1.10 Toner Supply Cover ................................................................................................................................................................................10-1410.5.1.10.1 Removing the Toner Supply Cover.................................................................................................................................................10-14
10.5.1.11 Fixing/Feeding Unit Cover .....................................................................................................................................................................10-1410.5.1.11.1 Removing the Duplexing Feed Front Cover ...................................................................................................................................10-1410.5.1.11.2 Removing the Fixing/Feeding Unit Front Cover ............................................................................................................................10-1510.5.1.11.3 Removing the Fixing/Feeding Unit Middle Cover .........................................................................................................................10-15
Contents
10.5.1.12 Fixing Cover (Upper).............................................................................................................................................................................. 10-1510.5.1.12.1 Removing the Fixing Upper Cover................................................................................................................................................. 10-15
10.5.1.13 Fixing Cover (Lower) ............................................................................................................................................................................. 10-1610.5.1.13.1 Removing the Fixing Front Cover .................................................................................................................................................. 10-16
10.5.1.14 Main Controller Box Cover .................................................................................................................................................................... 10-1710.5.1.14.1 Before Removing the Main Controller Box Cover......................................................................................................................... 10-1710.5.1.14.2 Removing the Main Controller Box Cover..................................................................................................................................... 10-17
10.5.1.15 Reader Left Cover................................................................................................................................................................................... 10-1710.5.1.15.1 Removing the Reader Left Cover ................................................................................................................................................... 10-17
10.5.1.16 Reader Right Cover ................................................................................................................................................................................ 10-1710.5.1.16.1 Removing the Reader Right Cover ................................................................................................................................................. 10-17
10.5.1.17 Reader Front Cover................................................................................................................................................................................. 10-1710.5.1.17.1 Before Detaching the Reader Front Cover...................................................................................................................................... 10-1710.5.1.17.2 Detaching the Reader Front Cover ................................................................................................................................................. 10-17
10.5.1.18 Reader Rear Cover.................................................................................................................................................................................. 10-1810.5.1.18.1 Detaching the Reader Rear Cover................................................................................................................................................... 10-18
10.5.2 Left Deck Drive Assembly .................................................................................................................................................... 10-1910.5.2.1 Before Removing the Left Deck Drive Assembly.................................................................................................................................... 10-1910.5.2.2 Removing the Left Deck Drive Assembly................................................................................................................................................ 10-19
10.5.3 Manual Feed Pickup Drive Assembly ................................................................................................................................... 10-1910.5.3.1 Before Removing the Manual Pickup Drive Assembly............................................................................................................................ 10-1910.5.3.2 Removing the Manual Pickup Drive Assembly ....................................................................................................................................... 10-19
10.5.4 Vertical Path Drive Assembly ............................................................................................................................................... 10-1910.5.4.1 Before Removing the Vertical Path Drive Assembly ............................................................................................................................... 10-1910.5.4.2 Removing the Vertical Path Drive Assembly........................................................................................................................................... 10-19
10.5.5 Waste Toner Drive Assembly................................................................................................................................................ 10-2010.5.5.1 Before Removing the Collecting Toner Drive Assembly......................................................................................................................... 10-2010.5.5.2 Removing the Collecting Toner Drive Assembly..................................................................................................................................... 10-20
10.5.6 Main Drive Assembly ............................................................................................................................................................ 10-2110.5.6.1 Fitting the Drive Belt ................................................................................................................................................................................ 10-21
10.5.7 Cassette Pickup Drive Assembly ........................................................................................................................................... 10-2110.5.7.1 Before Removing the Cassette Pickup Drive Assembly .......................................................................................................................... 10-2110.5.7.2 Removing the Cassette Pickup Drive Assembly ...................................................................................................................................... 10-21
10.5.8 Fixing Drive Assembly .......................................................................................................................................................... 10-2210.5.8.1 Before Removing the Fixing Drive Assembly ......................................................................................................................................... 10-2210.5.8.2 Removing the Fixing Drive Assembly ..................................................................................................................................................... 10-22
10.5.9 Power Supply Unit ................................................................................................................................................................. 10-2210.5.9.1 Removing the Charger unit....................................................................................................................................................................... 10-2210.5.9.2 Points to Note At Occurrence of Charger unit Malfunction ..................................................................................................................... 10-22
10.5.10 Duplex Unit PCB ................................................................................................................................................................. 10-2310.5.10.1 Before Removing the Duplex unit PCB ................................................................................................................................................. 10-2310.5.10.2 Removing the Duplex Unit PCB ............................................................................................................................................................ 10-23
10.5.11 Control Panel ....................................................................................................................................................................... 10-2310.5.11.1 Before Removing Control Panel ............................................................................................................................................................ 10-2310.5.11.2 Removing Control Panel ........................................................................................................................................................................ 10-23
10.5.12 DC Controller PCB.............................................................................................................................................................. 10-2410.5.12.1 Before Removing DC Controller PCB .................................................................................................................................................. 10-2410.5.12.2 Removing DC Controller PCB .............................................................................................................................................................. 10-2410.5.12.3 When Replacing DC Controller PCB .................................................................................................................................................... 10-24
10.5.13 Printer Power Supply PCB................................................................................................................................................... 10-2410.5.13.1 Before Removing Printer Power Supply PCB ....................................................................................................................................... 10-2410.5.13.2 Removing Printer Power Supply PCB ................................................................................................................................................... 10-24
10.5.14 Option Power Supply PCB .................................................................................................................................................. 10-2510.5.14.1 Before Removing Accessories Power Supply PCB ............................................................................................................................... 10-2510.5.14.2 Removing Accessories Power Supply PCB ........................................................................................................................................... 10-25
10.5.15 Fixing Heater Power Supply PCB ....................................................................................................................................... 10-2510.5.15.1 Before Removing Fixing Heater Power Supply PCB ............................................................................................................................ 10-2510.5.15.2 Removing Fixing Heater Power Supply PCB ........................................................................................................................................ 10-25
10.5.16 Anti-Rush Current PCB ....................................................................................................................................................... 10-2610.5.16.1 Before Removing Anti-Rush Current PCB ........................................................................................................................................... 10-26
Contents
10.5.16.2 Removing Anti-Rush Current PCB ........................................................................................................................................................10-2610.5.17 High-Voltage Transformer (AC) ......................................................................................................................................... 10-27
10.5.17.1 Before Removing High Voltage Transformer ........................................................................................................................................10-2710.5.17.2 Removing High Voltage Transformer ...................................................................................................................................................10-2710.5.17.3 Removing High Voltage Transformer ....................................................................................................................................................10-27
10.5.18 HVT PCB............................................................................................................................................................................. 10-2810.5.18.1 Before Removing HVT PCB .................................................................................................................................................................10-2810.5.18.2 Removing HVT PCB .............................................................................................................................................................................10-2810.5.18.3 When Replacing HVT PCB ...................................................................................................................................................................10-28
10.5.19 Separation Clew AC bias PCB ............................................................................................................................................ 10-2810.5.19.1 Before Removing Separation Claw AC PCB .........................................................................................................................................10-2810.5.19.2 Removing Separation Claw AC PCB ....................................................................................................................................................10-28
10.5.20 Motor Driver PCB................................................................................................................................................................ 10-2810.5.20.1 Before Removing Motor Driver PCB ....................................................................................................................................................10-2810.5.20.2 Removing Motor Driver PCB ................................................................................................................................................................10-28
10.5.21 Primary Fan Duct ................................................................................................................................................................ 10-2810.5.21.1 Before Removing Primary fan Duct ......................................................................................................................................................10-2810.5.21.2 Removing Primary fan Duct ..................................................................................................................................................................10-29
10.5.22 Primary Charging Assembly Fan......................................................................................................................................... 10-2910.5.22.1 Before Removing Primary Charging Fan ..............................................................................................................................................10-2910.5.22.2 Removing the Primary Charging Cooling Fan........................................................................................................................................10-29
10.5.23 De-Curling Fan .................................................................................................................................................................... 10-2910.5.23.1 Before Removing the Curl-Removing Fan .............................................................................................................................................10-2910.5.23.2 Removing the Curl-Removing Fan .........................................................................................................................................................10-29
10.5.24 Feeding Fan.......................................................................................................................................................................... 10-2910.5.24.1 Before Removing the Feeding Fan .........................................................................................................................................................10-2910.5.24.2 Removing the Feeding Fan .....................................................................................................................................................................10-30
10.5.25 HVT Fan .............................................................................................................................................................................. 10-3010.5.25.1 Before Removing the HVT Fan ..............................................................................................................................................................10-3010.5.25.2 Removing the HVT Fan ..........................................................................................................................................................................10-30
10.5.26 Duplex Feed Fan .................................................................................................................................................................. 10-3010.5.26.1 Before Removing the Duplex Feeding Fan.............................................................................................................................................10-3010.5.26.2 Removing the Duplex Feeding Fan.........................................................................................................................................................10-30
10.5.27 Exhaust Fan.......................................................................................................................................................................... 10-3110.5.27.1 Before Removing the Exhaust Fan .........................................................................................................................................................10-3110.5.27.2 Removing the Exhaust Fan .....................................................................................................................................................................10-31
10.5.28 DC Power Supply Fan ......................................................................................................................................................... 10-3110.5.28.1 Before Removing the DC Power Supply Fan .........................................................................................................................................10-3110.5.28.2 Removing the DC Power Supply Fan .....................................................................................................................................................10-31
10.5.29 Fixing Heater Power Supply Cooling Fan ........................................................................................................................... 10-3210.5.29.1 Before Removing the Fixing Heater Power Supply Cooling Fan...........................................................................................................10-3210.5.29.2 Removing the Fixing Heater Power Supply Cooling Fan.......................................................................................................................10-32
10.5.30 Circulation Duct Fan............................................................................................................................................................ 10-3210.5.30.1 Before Removing the Circulation Duct Fan............................................................................................................................................10-3210.5.30.2 Removing the Circulation Duct Fan .......................................................................................................................................................10-32
10.5.31 Motor of Main Drive Assembly........................................................................................................................................... 10-3310.5.31.1 Before Removing the Main Motor ..........................................................................................................................................................10-3310.5.31.2 Removing the Main Motor......................................................................................................................................................................10-33
10.5.32 Fixing Driver Motor............................................................................................................................................................. 10-3310.5.32.1 Before Removing the Fixing Motor........................................................................................................................................................10-3310.5.32.2 Removing the Fixing Motor....................................................................................................................................................................10-33
10.5.33 Right Door ........................................................................................................................................................................... 10-3410.5.33.1 Before Removing the Right Door Unit (Upper) .....................................................................................................................................10-3410.5.33.2 Removing the Right Door Unit (Upper) .................................................................................................................................................10-34
Chapter 10
10-1
10.1 Control Panel
10.1.1 Overview0015-4623
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's control panel consists of the following PCBs, LCD, and touch panel, and possesses the following principal functions:- LCD indication- contrast adjustment- touch switch input- hard key input
F-10-1
10.1.2 LCD Indication Processing0015-4625
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The CPU found on the main controller PCB serves to feed data (display data) to the control panel CPU on the control panel according to program instructions.The data goes through the control panel CPU PCB to reach the color LCD.
10.1.3 Adjusting the LCD Contrast0015-4626
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine is equipped with a density control volume (VR6801) on its keypad PCB so that the user can adjust the contrast of the LCD to suit individual needs.
10.1.4 Functions of the Control Panel CPU0015-4627
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- Monitoring Key InputsIt communicates the inputs from the keypads and function keys to the CPU on the main control PCB.
- Monitoring the Touch Panel InputsIt communicates the inputs from the touch panel to the CPU on the main controller PCB.
- Controlling the Buzzer Sound- Turning On Control Panel LEDs
MEMO:The color LCD is operated by the main controller, and the control panel CPU PCB serves to relay the drive signal.
10.2 Counters
10.2.1 Soft Counters0015-4628
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine possesses soft counters used to keep track of the number of prints it has made. The counter readings are indicated in response to a press on the Checkkey on the control panel.The counters are controlled by the main controller PCB, and the readings are incremented in response to detection of paper by the following sensors at time ofcopier/printer operation:
Main controller PCB
Control panel control block
Control panel CPU PCBTouch panel
Color LCD
Control panelKeypad PCB
Control panel inverter PCB
J1018A,J1018B
J511
J1114
J1110,J1111
J6801,J6802J1
J1112
J1113
Control panel
Chapter 10
10-2
T-10-1
The counters may be grouped into 8 types, a total of 16 individual types when further divided according to paper size (large and small); specifically,T-10-2
*1: at time of shipmen, B4 or smaller.If the user wants B4 to be counted as a large size, the setting may be changed in service mode.
The following shows the default counter types valid at time of shipment:T-10-3
100V
T-10-4
120 V, 230 V (outside Europe)
T-10-5
Copier/printer operation Counter name
Simplex mode inside delivery paper sensor (PS35)
Duplex mode duplex pre-registration sensor (PS30)
Finisher mode delivery sensor
Copier/printer mode Large size Small size*1
Local copy A B
PDL print C D
Box print E F
Remote copy print G H
Fax reception print I J
Report print K L
Duplex print M N
Scan O P
Counter Description*1 Default Change
counter 1 total (A through L) ON not possible
counter 2 - OFF possible
counter 3 - OFF possible
counte 4 - OFF possible
counter 5 - OFF possible
counter 6 - OFF possible
Counter Description*1 Default Change
counter 1 total (A through L) ON not possible
counter 2 total, large (ACEGIK) ON possible
counter 3 copy (total 1; ABGH) ON possible
counter 4 copy (large; AG) ON possible
counter 5 - OFF possible
counter 6 - OFF possible
Chapter 10
10-3
230V (inside Europe)
*1: the notation in parentheses indicates the support mode of the basic counter.*2: the counter type may be changed or counter display may be enabled or disabled in service mode (not applicable to counter 1).
10.3 Fans
10.3.1 Arrangement, Functions, and Error Codes0015-4629
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-10-6
T-10-7
T-10-8
Counter Description*1 Default Change
counter 1 total (A through L) ON not possible
counter 2 total, large (ACEGIK) ON possible
counter 3 total, small (BDFHJL) ON possible
counter 4 scan (total 1; OP) ON possible
counter 5 - OFF possible
counter 6 - OFF possible
The following shows the names of the fans mounted to the machine and the functions and error codes associated with them:
Notation Name Function 2-speed control (voltage) Error code
FM1 feed fan keeps print paper to feed belt yes (24/12 V) E805-0002
FM2 primary charging cooling fan cools the primary charging assembly and the cleaner yes (24/12 V) E824-0001
FM3 heat discharge fan discharges exhaust of fans outside the machine yes (24/12 V) E805-0001
FM4 controller cooling fan cools the laser unit, developing block drive block, and controller
yes (24/12 V) E121-0001
FM5 curl-removing fan removes curl from print paper after fixing yes (24/12 V) -
FM6 DC power supply fan cools power supply PCB yes (24/12 V) E804-0000
FM7 fixing heater power supply cooling fan
cools fixing power supply yes (24/12 V) E804-0001
FM8 duplex feed fan cools the duplex feed motor non (24 V) -
FM9 circulation duct fan cools the inside of the machine yes (24/12 V) -
FM10 ACC (accessory) power supply fan cools the ACC power supply yes (24/12 V) E804-0002
FM11 HVT fan cools the HVT unit yes (24/12 V) -
FM501 reader unit cooling fan cools the reader unit no (24 V) -
The following shows the arrangement of the fans and the direction of air current:
Chapter 10
10-4
F-10-2
10.3.2 Controlling the Speed of the Fans0015-4631
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Some of the fans mounted in the machine are controlled to 2 different speeds, switched over by the voltage switchover circuit of individual fans.
F-10-3
10.3.3 Sequence of Operation0015-4632
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-10-4
FM3
FM1
FM4
FM7
FM9
FM6
FM5
FM8
FM2
FM501
FM10
FM11
Voltage switchover circuit
CPU
DC controller PCB
Fan
24V or 12VFull speed signal
24V 12V
Lock signal
Half speed signal
Main power switch ON
Main power switchOFF
In reader operation
Accessories power supply fan (FM10)
HVT fan (FM11)
WMUPPrinter unit status WMUPR Standby Printing Power save Door openJamAfter printing
: full speed : half speed
Sleep 1 Sleep 3
Feed fan (FM1)
DC power supply fan (FM6)
Circulation duct fan (FM9)
Heat discharge fan (FM3)
Primary charging cooling fan (FM2)
Curl-removing fan (FM5)
Controller cooling fan(FM4)
Fixing power supply cooling fan (FM7)
Duplex feeding fan (FM8)
Chapter 10
10-5
10.4 Power Supply System
10.4.1 Power Supply
10.4.1.1 Overview0015-4633
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The supply of DC power of the machine is controlled by the DC power supply PCB. The following shows the various PCBs and components associated with thesupply of DC power:
T-10-9
10.4.1.2 Distribution of Power and the Switches0015-4634
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The various loads of the machine are supplied with power by means of the following switches:
1. 100V ModelT-10-10
T-10-11
2. 120/230-V Model
Name Description
ACC power supply PCB -generates DC power from AC power-protects against overcurrent-power supply to reader and charger unit
DC power supply PCB -generates DC power from AC power-protects against overcurrent
Rush current prevention PCB -limits rush current for the fixing feed unit, duplex unit, and high-voltage PCB
Main power switch (SW1) -serves as the power switch for loads other than the drum heater (H3), cassette heater (H4), and deck heater (H5)
Environment switch (SW3) -turns on/off the drum heater (H3), cassette heater (H4), and deck heater (H5)
Cassette heater switch (SW4) - turns on/off the cassette heater (H4) and the deck heater
Main power swish OFF Sleep Warm-up (other than initial)
Standby/ power save Copying/ printing
Env.switch OFF
Main switch OFF ON
Cassette switch OFF ON OFF ON OFF ON OFF ON OFF ON
Latch relay RL OFF OFF OFF OFF OFF OFF ON ON ON ON
Drum heater OFF OFF OFF OFF OFF OFF ON/OFF
ON/OFF
ON/OFF
ON/OFF
Cassette heater ON ON ON ON OFF OFF ON ON ON ON
Reader unit heater OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
Main power switch OFF Sleep Warm-up (other than initial)
Standby/ power save Copying/ printing
Env. switch ON
Main switch OFF ON
Cassette switch OFF ON OFF ON OFF ON OFF ON OFF ON
Latch relay RL ON ON OFF OFF ON ON ON ON ON ON
Drum heater ON ON ON/ OFF
ON/ OFF
OFF OFF ON/ OFF ON/ OFF ON/ OFF ON/ OFF
Cassette heater ON ON ON ON OFF OFF ON ON ON ON
Reader unit heater ON ON ON ON OFF OFF OFF OFF OFF OFF
Chapter 10
10-6
T-10-12
T-10-13
The following shows the default settings of the machine's environment switch (SW3) and cassette heater switch (SW4):T-10-14
The following shows the distribution of power inside the machine:
Main power switch OFF Sleep Warm-up (other than initial)
Standby/ power save Copying/ printing
Env. switch OFF
Main power switch OFF ON
Cassette switch OFF ON OFF ON OFF ON OFF ON OFF ON
Control relay OFF OFF OFF OFF ON ON ON ON ON ON
Drum heater OFF OFF OFF OFF ON ON ON ON ON ON
Cassette heater ON ON ON ON OFF OFF ON ON ON ON
Reader unit heater OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
Main power switch OFF Sleep Warm-up (other than initial)
Standby/ power save Copying/ printing
Env. switch ON
Main switch OFF ON
Cassette switch OFF ON OFF ON OFF ON OFF ON OFF ON
Control relay OFF OFF OFF OFF ON ON ON ON ON ON
Drum heater ON ON ON ON ON ON ON ON ON ON
Cassette heater ON ON ON ON OFF OFF ON ON ON ON
Reader unit heater ON ON ON ON OFF OFF OFF OFF OFF OFF
Default setting 100-V model 120-V model 230-V model
Environment switchON OFF OFF
Cassette heaterswitch OFF not
present OFF
Chapter 10
10-7
F-10-5
10.4.2 Rated Output of the DC Power Supply PCB
10.4.2.1 Rated Output of the DC Power Supply PCB0015-4635
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the ratings and the power supply tolerances of the DC power supply PCB:T-10-15
10.4.2.2 Rated Output of the Accessories Power Supply PCB0015-4636
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following shows the ratings and the power supply tolerances of the accessories power supply PCB:
Output 5VA3VA13VA23VA3
3VB
24VU124VU224VU324VU4
12VU
Uninterruptive/interruptive interruptive interruptive uninterruptive interruptive interruptive
Rated output +5.10V +3.40V +3.50V +24.0V +12.0V
Power supply tolerance +/-3% 3.25-3.46V +/-2% (1.0-2.0A) +/-5% +/-5%
Leakage breaker
ELC
B
Line noise filter
LF1
Drum heater(H3)
Cassette heater(H4)
DC controller PCB
Reader controller PCB
Main controller PCB/ Video PCB
Main power switch(SW1) Drum
temperature control PCB
AC input
3.3VA12VU324VU3
24V13V
3.3VB3.3VA212VU/5V24V
HVT PCB Fixing
feedunit
Power accumulateing unit
(only for iR5075 Japanese models)
13V converter PCB
24V
24V
5V5.7V
24V
5V
Laser driverPCB
Laser scannermotor
24VU3
Fax unit (accessory)
24VU3
Pper Deck(accessory)
24VFinisher (accessory)
24V24V
24V
5V24VU2
Motor driver PCB
Fixing motor(M3)
Main motor(M2)
Drum motor(M1)
24V
5V
24V
U1
Duplex drive PCB
Accessories power
supply PCB
Deck heater(H5)
Mirror heater(H502)
Lens heater(H501)
DC power supply
PCB
Rush current prevention PCB
Manual feeder door switch(SW6)
Front cover switch(SW2)
24V
Clutch solenoid
24V
BD PCB
24V
5V 10V
InverterPCB
CCD/APPCB
A
C
AC Potential
controlPCB
Separationclew
AC bias PCB
Fixing heaterAC line
12VU
I/F PCB/ Memory PCB
24V
MotorfanADF
24V12V 5V3.3V
24V
5V
3.3V
Environment switch(SW3)
Choke coilFixing heater
driver PCB
Heater switch(SW4) AC
driver PCB
12V
B
B
Chapter 10
10-8
T-10-16
10.4.3 Protection Function
10.4.3.1 Protective Functions0015-4637
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's DC power supply PCB and the power supply PCB for its accessories are equipped with overcurrent and overvoltage protective functions that willcut off power to prevent damage to circuitry in the event of an overcurrent or overvoltage occurring as a result of a short circuit or other fault.A fault in 3VB (uninterruptive power supply) will cut off all power of the machine; on the other hand, a fault in any other power supply will cut off all power toloads other than 3VB (uninterruptive power supply).
If a fault has occurred in 3VB (uninterruptive power supply), turn off the main power switch of the printer unit, and remove the cause that has activated the protectivecircuit; then, replace the DC power supply PCB. (The fuse on the DC power supply PCB is likely to have blown.)Other than that, turn off the main power switch of the printer unit, and remove the cause that has activated the protective circuit; then, leave the machine alone forabout 3 min or more, and turn the power back on to reset the protective circuit.
10.4.4 Backup Battery
10.4.4.1 Backup Battery0015-4638
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine's main controller PCB and DC controller PCB are equipped with each of one lithium battery that serves as a source of backup power to retain variousdata in the event of a power outage or disconnection of the power plug.
T-10-17
You must always be sure that the battery is replaced correctly. Be sure to replace it with a battery of a type indicated by the manufacturer of the unit (bearing thesame model name or equivalent).Be sure also to dispose of the removed battery as instructed by the manufacturer of the battery.
10.4.5 Energy-Saving Function
10.4.5.1 Overview0015-4639
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1. Standby StateWhen the machine is in a standby state, all its loads are supplied with power and the machine is ready to start operation at any time.
2. Sleep State2-1. Sleep 1When the machine is in sleep 1, its laser scanner will not rotate even when a key on the control panel is pressed.2-2. Sleep 3When the machine is in sleep 3, only 3VB on the DC power supply PCB is supplied with power.The machine moves from sleep 3 to standby in response to the following:- print job- press on the control panel power switch- fax reception- fax delayed transmissionThe following shows the loads that remain supplied with power when the machine is in sleep 3.
Output 24VA
Uninterruptive/interruptive interruptive
Rated output 24V
Power supplytolerance +7-5%
Battery specifications manganese dioxide lithium battery (3 V, 1000 mAh)
Battery life main controller PCB: about 8.8 yr (with power plug disconnected)
Battery replacement not possible in the field on its own
Chapter 10
10-9
F-10-6
3. AC Off StateThe machine is in an AC off state when its main power switch remains off, with all its power supplies and heater control mechanisms also remaining off.
4. Power Supply ArrangementThe following shows how the various loads of the machine are supplied with power while the machine is in individual states:
T-10-18
*Output from the main controller PCB.
10.4.5.2 SNMP setup0015-4640
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When the machine is used as a Windows printer, enabling 'Use SNMP' causes the operating system to collect machine status information at specific intervals, pre-venting the machine from starting a sleep state.To avoid the situation, disable the setting (Windows' printer properties).-Disabling 'Use SNMP'1) Select 'Configure Port' on the Ports screen (printer properties).
Operation set AC off Sleep 3 Front door open Sleep 1 Standby, copying,
power save
Input
Main power switch OFF ON ON ON ON
Front door switch - - OFF ON ON
RMT2* - 0 1 1 1
Output
3VB OFF ON ON ON ON
3VB OFF OFF ON ON ON
5V OFF OFF ON ON ON
12VU OFF OFF ON ON ON
24VU1 OFF OFF ON ON ON
24VU2/3/4 OFF OFF OFF ON ON
CPUSDRAM
LAN controller block
Image processing block
Control panelpower switch
Fax reception detection
Hard disk drive
Scanner unit Printer unit
supplied with power in sleep 3
not supplied with power in sleep 3
Main controller PCB
Chapter 10
10-10
F-10-72) Remove the check mark from 'SNMP Status Enabled'.
Chapter 10
10-11
F-10-8
Chapter 10
10-12
10.5 Parts Replacement Procedure
10.5.1 External Covers
10.5.1.1 Right Cover (Lower Rear)
10.5.1.1.1 Removing the Right Cover (Lower Rear)
0015-6693iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the right cover (lower rear)[2].- 2 screws [1]
F-10-9
10.5.1.2 Right Cover (Upper Rear)
10.5.1.2.1 Removing the Right Cover (Upper Rear)
0015-8142iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the connector [1] of the reader unit communication cable.
F-10-102) Detach the right cover (upper rear) [2].
- 2 screws [1]
F-10-11
10.5.1.3 Right Cover (Upper)
10.5.1.3.1 Removing the Right Cover (Upper)
0015-6683iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the toner supply cover [1].2) Detach the right cover (upper) [3].
- 2 screws [2]
F-10-12
10.5.1.4 Left Cover (Upper)
10.5.1.4.1 Removing the Left Cover (Upper)
0015-6680iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left cover (upper) [2].- 2 screws [1]
F-10-13
[1]
[2]
[1]
[2][1]
[1]
[2]
[3]
[1]
[1] [2]
Chapter 10
10-13
10.5.1.5 Front Cover
10.5.1.5.1 Removing the Front Cover
0015-6691iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Pull the pin [2] up to draw out.- Stopper [1] (Pull forward to remove)
2) Lift the front cover [3] to detach.- 1 screw [4]
F-10-14
10.5.1.6 Rear Cover (Upper)
10.5.1.6.1 Removing the Rear Cover (Upper)
0015-6682iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the wire saddle [1] and disconnect the connector [2] of the readerunit communication cable.
F-10-152) Detach the rear cover (upper) [2].
- 6 screws [1]
F-10-16
10.5.1.7 Rear Cover (Lower)
10.5.1.7.1 Before Removing the Rear Cover (Lower)
0015-8306iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
10.5.1.7.2 Removing the Rear Cover (Lower)
0015-6688iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (lower) [2].- 8 screws [1]
F-10-17
10.5.1.8 Left Cover (Lower)
10.5.1.8.1 Before Removing the Left Cover (Lower)
0015-8309iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left cover (middle). (page 10-14)Reference[Removing theLeft Cover (Middle)]
10.5.1.8.2 Removing the Left Cover (Lower)
0015-6695iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the 2 grip covers [1].2) Slide out the left deck [2], the cassette 3 [3] and the cassette 4 [4].3) Detach the left cover (lower) [6].
- 6 screws [5]
[2] [1]
[4]
[3]
[1] [2]
[1]
[1]
[2]
[1]
[1]
[2]
[1][1]
[1]
Chapter 10
10-14
F-10-18
10.5.1.9 Left Cover (Middle)
10.5.1.9.1 Removing the Left Cover (Middle)
0015-6681iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the delivery cover [2].- 3 screws [1]
2) Disconnect the reader power cable [3].3) Open the front cover [4].4) Open the toner supply cover [5].5) Detach the left cover (middle) [7].
- 6 screws [6]
F-10-19
10.5.1.10 Toner Supply Cover
10.5.1.10.1 Removing the Toner Supply Cover
0015-8152iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover [1].
F-10-202) Detach the toner supply cover [2].
- 2 screws [1] (Detach with the cover closed.)
F-10-21
10.5.1.11 Fixing/Feeding Unit Cover
10.5.1.11.1 Removing the Duplexing Feed Front Cover
0015-8201iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover [1].
F-10-222) Turn the fixing/feeding unit releasing lever [1] counterclockwise to un-
lock. Hold the lever to slide out the fixing/feeding unit [2] fully. (The du-plexing feed unit will be also slid out.)
MEMO:Perform the step above when sliding out the fixing/feeding unit.When removing the duplexing feed unit, slide out the duplexing feed unit on-ly.
[1][5] [5]
[2]
[3]
[4]
[5] [5][6]
[3]
[1] [4][6] [6]
[2] [5][6] [6] [7]
[1]
[1] [1]
[2]
[1]
Chapter 10
10-15
F-10-233) Remove the 2 jam removal levers [1] of the duplexing feed unit and detach
the duplexing feed front cover [3].- 3 screws [2]
F-10-24
10.5.1.11.2 Removing the Fixing/Feeding Unit Front Cover
0015-8258iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover [1].
F-10-252) Turn the fixing/feeding unit releasing lever [1] counterclockwise to un-
lock. Hold the lever [1] to slide out the fixing/feeding unit [2] fully. (Theduplexing feed unit will also be slid out.)
F-10-263) Detach the feeding assembly front cover (right) [2].
- 2 screws [1]
F-10-27
10.5.1.11.3 Removing the Fixing/Feeding Unit Middle Cover
0015-8259iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
2) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-moving the Fixing/Feeding Unit Front Cover]
3) Detach the fixing/feeding unit middle cover [2].- 2 screws [1]
F-10-28
10.5.1.12 Fixing Cover (Upper)
10.5.1.12.1 Removing the Fixing Upper Cover
0015-9419iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover [1].
[1] [2]
[1][2]
[2]
[2]
[3]
[1]
[1] [2]
[1]
[1]
[2]
[3]
[3]
[4]
Chapter 10
10-16
F-10-292) Turn the fixing/feeding unit releasing lever [1] counterclockwise to un-
lock. Hold the lever [1] to slide out the fixing/feeding unit [2] fully. (Theduplexing feed unit will also be slid out.)
F-10-303) Open the delivery unit [1] and detach the fixing upper cover [3].
- 1 screw [2]
F-10-31
10.5.1.13 Fixing Cover (Lower)
10.5.1.13.1 Removing the Fixing Front Cover
0015-9418iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the front cover [1].
F-10-322) Turn the fixing/feeding unit releasing lever [1] counterclockwise to un-
lock. Hold the lever [1] to slide out the fixing/feeding unit [2] fully. (Theduplexing feed unit will also be slid out.)
F-10-333) While pushing the rear hook shaft [1] of the fixing/feeding unit in the di-
rection of the arrow (to the machine’s front), turn the fixing/feeding unitreleasing lever [2] clockwise to lock.
F-10-344) Remove the knob [2] and the fixing/feeding unit releasing lever [4].
- 2 screws [1,3]
[1]
[1] [2]
[1]
[2] [3]
[1]
[1] [2]
[2]
[1]
Chapter 10
10-17
F-10-355) etach the fixing front cover [2].
- 2 screws [1]
F-10-36
10.5.1.14 Main Controller Box Cover
10.5.1.14.1 Before Removing the Main Controller Box Cover
0015-8310iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
10.5.1.14.2 Removing the Main Controller Box Cover
0015-6690iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the main controller box cover [2].- 4 screws [1]
F-10-37
10.5.1.15 Reader Left Cover
10.5.1.15.1 Removing the Reader Left Cover
0015-6685iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the reader left cover [2].- 2 screws [1]
F-10-38
10.5.1.16 Reader Right Cover
10.5.1.16.1 Removing the Reader Right Cover
0015-6684iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the reader right cover [2].- 2 screws [1]
F-10-39
10.5.1.17 Reader Front Cover
10.5.1.17.1 Before Detaching the Reader Front Cover
0015-8312iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the right cover (upper). (page 10-12)Reference[Removing theRight Cover (Upper)]
2) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
10.5.1.17.2 Detaching the Reader Front Cover
0015-6686iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the each screw [1] from the reader front cover [2] right and left.
[1]
[2]
[3]
[4]
[1]
[2]
[1]
[2]
���
���
���
���
Chapter 10
10-18
F-10-40
F-10-412) Lift the reader front cover and detach [1].
F-10-42
10.5.1.18 Reader Rear Cover
10.5.1.18.1 Detaching the Reader Rear Cover
0015-6687iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the cable clamp [1].2) Disconnect the 4 connectors [2].3) Remove the 2 screws [3].
F-10-434) Bend up the rubber cover [1], and remove the 2 screws [2] each; then de-
tach the 2 angle guide plates [3].
F-10-44
F-10-455) Fully open the ADF.6) Slide the reader rear cover [2] to the rear to detach.
- 3 screws [1]
Be careful not to damage the ADF open/close sensor arm [3].
���
���
���
���
���
[1]
[2]
[3][3]
������
���
��� ���
���
Chapter 10
10-19
F-10-46
10.5.2 Left Deck Drive Assembly
10.5.2.1 Before Removing the Left Deck Drive Assembly0015-5083
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the HVT PCB.(page 10-28)Reference[Removing HVT PCB]
10.5.2.2 Removing the Left Deck Drive Assembly0015-5085
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left deck drive assembly [4].- 4 screws [1]- 1 connector [2]- 2 wire saddles [3] (Free the harness)
F-10-47
10.5.3 Manual Feed Pickup Drive Assembly
10.5.3.1 Before Removing the Manual Pickup Drive Assembly
0015-5086
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Remove the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the main controller box cover.(page 10-17)Reference[Remov-ing the Main Controller Box Cover]
5) Remove the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
6) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
7) Remove the separation claw AC PCB unit. (page 10-28)Reference[Re-moving Separation Claw AC PCB]
10.5.3.2 Removing the Manual Pickup Drive Assembly0015-5089
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the scanner fan duct [2].- 2 screws [1]
Before removing the screw, make sure to mark the line in the following step.
2) Loosen the screw [3] to release the belt tensioner [4], and detach the belt[5].
F-10-483) Remove the pickup drive assembly [3].
- 4 screws [1]- 3 connectors [2]
F-10-49
10.5.4 Vertical Path Drive Assembly
10.5.4.1 Before Removing the Vertical Path Drive Assembly
0015-5090
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]5) Removing the Right Cover (Upper Rear). (page 10-12)Reference[Re-moving the Right Cover (Upper Rear)]6) Remove the main controller box. (page 4-13)Reference[Removing the
Main Controller Box]7) Detach the right cover (lower rear). (page 10-12)Reference[Removing
the Right Cover (Lower Rear)]8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-
moving the Collecting Toner Bottle Holder]
10.5.4.2 Removing the Vertical Path Drive Assembly0015-5096
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the 10 connectors on the motor driver PCB .2) Detach the motor driver PCB mounting base [3].
- 9 wire saddles (Free the harness [1])- 4 screws [2]
��� ���
������
[1] [1]
[1]
[2] [3] [3][4]
[1][1]
[4]
[3]
[2]
[5]
[1]
[2]
[2]
[1]
[3]
Chapter 10
10-20
F-10-503) Remove the vertical path drive assembly [3].
- 3 screws [1]- 1 wire saddle [2] (Free the harness)
F-10-51
10.5.5 Waste Toner Drive Assembly
10.5.5.1 Before Removing the Collecting Toner Drive Assembly
0015-5097
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]5) Removing the right cover (upper rear). (page 10-12)Reference[Remov-ing the Right Cover (Upper Rear)]6) Remove the main controller box. (page 4-13)Reference[Removing the
Main Controller Box]7) Detach the right cover (lower rear). (page 10-12)Reference[Removing
the Right Cover (Lower Rear)]8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-
moving the Collecting Toner Bottle Holder]
10.5.5.2 Removing the Collecting Toner Drive Assembly0015-5102
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect all of the connectors on the DC controller PCB.2) Pull out the DC controller mounting base [2], and turn it over.
- 14 wire saddles (Free the harness)- 1 edge saddle (Free the harness)- 1 reuse band- 8 screws [1] (Free the grounding wire)
F-10-523) Remove the DC controller mounting base [6].
- 3 connectors [1]- 2 wire saddles [2] (Free the harness [3])- 1 edge saddle [4] (Free the harness [5])
F-10-534) Remove the flywheel [2].
- 2 screws [1]
F-10-545) Loosen the belt tensioner [1] to detach the main motor belt [2].
[1] [1]
[1][2] [2]
[2] [2][3]
[1]
[1]
[2]
[3]
[1]
[1]
[1] [2]
[1]
[1][2]
Chapter 10
10-21
F-10-556) Remove the collecting toner drive assembly [2].
- 3 screws [1]
F-10-56
10.5.6 Main Drive Assembly
10.5.6.1 Fitting the Drive Belt0015-5103
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure that the drive belt is fitted to the pulley and the roller as shown in thefollowing figure.
[1] Main drive belt[2] Pickup drive belt
F-10-57
10.5.7 Cassette Pickup Drive Assembly
10.5.7.1 Before Removing the Cassette Pickup Drive Assembly
0015-6548
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]5) Removing the Right Cover (Upper Rear). (page 10-12)Reference[Re-moving the Right Cover (Upper Rear)]6) Remove the main controller box. (page 4-13)Reference[Removing the
Main Controller Box]7) Detach the right cover (lower rear). (page 10-12)Reference[Removing
the Right Cover (Lower Rear)]8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-
moving the Collecting Toner Bottle Holder]
10.5.7.2 Removing the Cassette Pickup Drive Assembly0015-5111
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the 10 connectors on the motor driver PCB.2) Remove the motor driver PCB mounting base [3].
- 9 wire saddles (Free the harness [1])- 4 screws [2]
F-10-58
- The removal procedure of the right deck pickup assembly and the cassette3/4 pickup assembly is the same. - An illustration uses a right door pickup assembly as an example to ex-plain.- An attempt removing the pickup assembly without removing the deck/cassette causes the lifter get trapped and may hold the pickup assemblyfrom sliding out.
3) Slide out the cassette 3 and the cassette 4.4) Open the manual tray cover and the right cover (lower).5) Disconnect the connector [3].
- 1 screw [1]- 1 connector cover [2]
6) Remove the pickup assembly [5].- 3 screws [4]
F-10-597) Remove the cassette pickup drive assembly [2].
- 3 screws [1]
[1] [2]
[1]
[2] [1]
[1] [1]
[1][2] [2]
[2] [2][3]
[3][4]
[4]
[5]
[1]
[2]
Chapter 10
10-22
F-10-60
10.5.8 Fixing Drive Assembly
10.5.8.1 Before Removing the Fixing Drive Assembly0015-8269
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
10.5.8.2 Removing the Fixing Drive Assembly0015-8271
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the fixing drive assembly [3].- 2 connectors [1]- 3 screws [2]
F-10-61
10.5.9 Power Supply Unit
10.5.9.1 Removing the Charger unit0016-2949
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit [3].- 1 Connector [1]- 5 Screw [2]
F-10-62
10.5.9.2 Points to Note At Occurrence of Charger unit Malfunction
0016-2950
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
E732 error may indicate the malfunction of the charger unit.In this case, perform the following after removing the charger unit.1) Open the wire saddle [1] and disconnect the connector [2] of the reader
unit communication cable.
F-10-632) Detach the rear cover (upper) [2].
- 6 screws [1]
F-10-643) Detach the rear cover (lower) [2].
- 8 Screw [1]
[1]
[1]
[2]
[1] [2][2]
[2] [3]
[1]
[2]
[3]
[1] [2]
[1]
[1]
[2]
Chapter 10
10-23
F-10-654) Disconnect the connector [1] of the auxiliary power and connect the jump-
er connector [2].
F-10-665) Once the main power is turned on, the following message is displayed on
the control panel."Time for maintenance work.The capacitor needs checking. Please call the service personnel.You can continue to use the machine, however, the operational speedduring printing may be slower than usual"
6) Once pressing "Close" button, a message, "The capacitor needs checking(Please call the service personnel)", is displayed at the bottom on the con-trol panel.
This is a temporary measure. Be sure to replace with the new one once youreceive the Power Accumulating Unit.
T-10-19
10.5.10 Duplex Unit PCB
10.5.10.1 Before Removing the Duplex unit PCB0015-9413
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit. (page 8-49)Reference[Removing theDuplex Feeding Unit]
10.5.10.2 Removing the Duplex Unit PCB0015-9412
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the duplex unit PCB [3].- 4 screws [1]
- 6 connectors [2]
F-10-67
10.5.11 Control Panel
10.5.11.1 Before Removing Control Panel 0015-6564
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the right cover (upper). (page 10-12)Reference[Removing theRight Cover (Upper)]
2) Detach the reader right cover. (page 10-17)Reference[Removing theReader Right Cover]
3) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
4) Detach the reader left cover. (page 10-17)Reference[Removing theReader Left Cover]
5) Detach the reader front cover. (page 10-17)Reference[Detaching theReader Front Cover]
10.5.11.2 Removing Control Panel 0015-5118
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the hopper front cover. 2) Remove the 5 screws [1] at right, left, rear of the control panel [2].
F-10-68
F-10-69
This step enables direct power supply from the auxiliary power to the reader/DADF. Therefore, the speed of continuous print after power-on (for approx. 15 min) becomes shorter.
[1]
[1]
[2]
[1][1]
[1]
[1] [2]
[1] [1]
[2]
[1]
[2]
[1]
[2]
[3]
[1][2]
[1] [2]
Chapter 10
10-24
F-10-703) Shift the control panel [3] together with the cover, and remove the use
band [1] and disconnect the connector [2]. Then, remove the control panel[3].
F-10-71
10.5.12 DC Controller PCB
10.5.12.1 Before Removing DC Controller PCB 0015-5119
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
10.5.12.2 Removing DC Controller PCB 0015-6585
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the DC controller PCB [2]. - 28 connectors - 8 screws [1]
F-10-72
10.5.12.3 When Replacing DC Controller PCB 0015-9987
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure to perform the followings when replacing the DC controller PCB.
1) Enter the latest values for the service mode indicated on the label [1] onthe back of the front cover with the service mode.
2) Enter the values indicated on the label [1] of the new PCB using the fol-lowing service mode items:
COPIER> ADJUST> HV-TR> D-PRE-TRCOPIER> ADJUST> HV-TR> D-HV-TRCOPIER> ADJUST> HV-SP> D-HV-SPCOPIER> ADJUST> DEVELOP> D-HV-DE
3) Move the J303 shorting connector [2] on the PCB from the existing to thenew PCB.
Make sure to connect the shorting connector. Otherwise, E004 occurs.
F-10-73
10.5.13 Printer Power Supply PCB
10.5.13.1 Before Removing Printer Power Supply PCB 0015-5122
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
2) Detach the left cover (middle). (page 10-14)Reference[Removing theLeft Cover (Middle)]
3) Detach the left cover (lower). (page 10-13)Reference[Removing theLeft Cover (Lower)]
10.5.13.2 Removing Printer Power Supply PCB 0015-5125
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the shield plate [2]. - 4 screws [1]
F-10-742) Detach the power supply cover [2].
- 9 screws [1]
[1]
[2]
[1][2] [3]
[1] [1]
[1]
[1]
[2]
[1]
[2]
[1]
[1]
[2]
Chapter 10
10-25
F-10-753) Remove the printer power supply PCB [2].
- 14 connectors - 2 screws [1]
F-10-76
10.5.14 Option Power Supply PCB
10.5.14.1 Before Removing Accessories Power Supply PCB
0015-6607
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
5) Detach the left cover (middle). (page 10-14)Reference[Removing theLeft Cover (Middle)]
6) Detach the left cover (lower). (page 10-13)Reference[Removing theLeft Cover (Lower)]
10.5.14.2 Removing Accessories Power Supply PCB 0015-5130
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Slide the power cord mount [4]. - 5 screws [1] - 5 connectors [2] - 1 edge saddle [3] (free the harness)
F-10-772) Remove the power cord mount [2].
- 3 connectors [1]
F-10-783) Remove the accessories power supply PCB [3].
- 3 screws [1] - 3 connectors [2]
F-10-79
10.5.15 Fixing Heater Power Supply PCB
10.5.15.1 Before Removing Fixing Heater Power Supply PCB
0015-6610
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
2) Detach the left cover (middle). (page 10-14)Reference[Removing theLeft Cover (Middle)]
10.5.15.2 Removing Fixing Heater Power Supply PCB 0015-5134
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1] [2] [1]
[1]
[1]
[2]
[1][1]
[2]
[4]
[3]
[2]
[1][2]
[1]
[1]
[2]
[3]
Chapter 10
10-26
1) Detach the mount cover [2]. - 5 screws [1]
F-10-802) Open the 2 wire saddles [1]. 3) Disconnect the 7 connectors [2]. 4) Remove the fixing heater power supply unit [4].
- 3 screws [3]
F-10-815) Detach the fixing heater power supply unit cover [2].
- 14 screws [1]
F-10-826) Remove the 2 reuse bands [2].
- 2 connectors [1] 7) Remove the fixing heater power supply PCB [4].
- 6 screws [3]
F-10-83
10.5.16 Anti-Rush Current PCB
10.5.16.1 Before Removing Anti-Rush Current PCB 0015-5135
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
10.5.16.2 Removing Anti-Rush Current PCB 0015-5136
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect all connectors on the DC controller PCB. 2) Remove the DC controller PCB mount [2] and turn it over.
- 14 wire saddles (free the harness) - 1 edge saddle (free the harness) - 1 reuse band - 8 screws [1] (free the grounding wire)
F-10-843) Remove the anti-rush current PCB [4].
- 3 connectors [1] - 3 PCB supports [3] - 1 screw [2]
[1]
[1] [1][1]
[2]
[1][2]
[2] [2][3] [3][4]
[1]
[1]
[1] [1]
[2]
[1][2]
[2] [3][3]
[3][3]
[4]
[1]
[1]
[1] [2]
Chapter 10
10-27
F-10-85
10.5.17 High-Voltage Transformer (AC)
10.5.17.1 Before Removing High Voltage Transformer 0015-9479
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
10.5.17.2 Removing High Voltage Transformer 0015-9478
iR5075 / iR5075N
1) Remove the transformer unit [3] by sliding it to the left. - 2 screws [1] - 3 connectors [2]
F-10-862) Remove the transformer [4].
- 2 screws [1] - 1 wire saddle [2] - 1 connector [3]
F-10-87
10.5.17.3 Removing High Voltage Transformer0016-1513
iR5065 / iR 5055 / iR5065N / iR5055N
1) Remove the transformer unit [3] by sliding it to the left. - 2 screws [1] - 2 connectors [2]
F-10-882) Remove one connector [1] on the HVT PCB.
F-10-893) Remove the transformer [2]. - 2 screws [1]
[2][1][3]
[3] [4]
[1]
[3]
[2]
[2]
[1]
[1][2][3]
[4]
[3]
[1]
[2]
[1]
Chapter 10
10-28
F-10-90
10.5.18 HVT PCB
10.5.18.1 Before Removing HVT PCB 0015-5139
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
10.5.18.2 Removing HVT PCB 0015-5140
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the grounding wire [2]. - 1 screw [1]
2) Disconnect the 9 connectors [3]. 3) Remove the HVT PCB [5].
- 4 screws [4]
F-10-91
10.5.18.3 When Replacing HVT PCB 0015-9992
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Enter the values indicated on the label of the HVT PCB using the followingservice mode items:
COPIER>ADJUST>HV-TR>H-PRE-TRCOPIER>ADJUST>HV-TR>HVT-TRCOPIER>ADJUST>HV-SP>HVT-SPCOPIER>ADJUST>DEVELOP>HVT-DE
10.5.19 Separation Clew AC bias PCB
10.5.19.1 Before Removing Separation Claw AC PCB 0015-9422
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper).(page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover.(page 10-17)Reference[Removingthe Main Controller Box Cover]
3) Detach the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
4) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
10.5.19.2 Removing Separation Claw AC PCB 0015-9423
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the separation claw AC PCB unit [3]. - 1 connector [1] - 2 screws [2] (free the grounding wire)
F-10-92
10.5.20 Motor Driver PCB
10.5.20.1 Before Removing Motor Driver PCB 0015-5143
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Remove the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
4) Remove the main controller box cover.(page 10-17)Reference[Remov-ing the Main Controller Box Cover]
5) Remove the right cover (upper rear).(page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
6) Remove the main controller box. (page 4-13)Reference[Removing theMain Controller Box]
7) Remove the right cover (lower rear). (page 10-12)Reference[Removingthe Right Cover (Lower Rear)]
8) Remove the collecting toner bottle holder. (page 5-29)Reference[Re-moving the Collecting Toner Bottle Holder]
10.5.20.2 Removing Motor Driver PCB 0015-5147
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the motor driver PCB [2]. - 6 screws [1] - 10 connectors
F-10-93
10.5.21 Primary Fan Duct
10.5.21.1 Before Removing Primary fan Duct 0015-9386
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1]
[1]
[2]
[1][2][3]
[4]
[4] [5]
[2]
[1]
[3][4] [4]
[1][2]
[3]
[1]
[1]
[1]
[2]
Chapter 10
10-29
1) Detach the front cover. (page 10-13)Reference[Removing the FrontCover]
2) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
10.5.21.2 Removing Primary fan Duct 0015-9387
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the connector cover [2]. - 1 screw [1]
F-10-942) Remove the primary fan duct [3].
- 2 screws [1] - 1 connector [2]
F-10-95
10.5.22 Primary Charging Assembly Fan
10.5.22.1 Before Removing Primary Charging Fan 0015-8448
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the toner supply cover. (page 10-14)Reference[Removing theToner Supply Cover]
2) Remove the primary fan duct. (page 10-29)Reference[Removing Prima-ry fan Duct]
10.5.22.2 Removing the Primary Charging Cooling Fan0015-5148
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fan cover [2].- Screw [1] 6pc.
F-10-962) Disconnect the connector [1] from behind, and detach the primary charg-
ing cooling fan [2].
F-10-97
10.5.23 De-Curling Fan
10.5.23.1 Before Removing the Curl-Removing Fan0015-8449
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
2) Detach the fixing drive assembly. (page 10-22)Reference[Removing theFixing Drive Assembly]
10.5.23.2 Removing the Curl-Removing Fan0015-5149
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the curl-removing fan assembly [4].- Screw [1] 1pc.- Wire saddle [2] 2pc.- Edge saddle [3] 3pc.
F-10-982) Separate the fan duct [2] and the curl-removing fan [3].
- Screw [1] 2pc.
F-10-99
10.5.24 Feeding Fan
10.5.24.1 Before Removing the Feeding Fan0015-5150
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing the
[1][2]
[1]
[2]
[3]
[1]
[1]
[1]
[2]
[1]
[2]
[4] [2] [1]
[2]
[3]
[1]
[1]
[2] [3]
Chapter 10
10-30
Rear Cover (Upper)]
10.5.24.2 Removing the Feeding Fan0015-5152
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect all the connectors of the DC controller PCB.2) Detach the DC controller base [2]; then, turn it over.
- Wire saddle 14pc. (to free the harness)- Edge saddle 1pc. (to free the harness)- Reuse band 1pc.- Screw [1] 8pc. (to remove the grounding wire)
F-10-1003) Detach the DC controller base [6].
- Connector [1] 3pc.- Wire saddle [2] 2pc. (to free the harness [3])- Edge saddle [4] 1pc. (to free the harness [5])
F-10-1014) Detach the feed fan cover [2].
- Screw [1] 3pc.5) Detach the feed fan [4].
- Screw [3] 3pc.
F-10-102
10.5.25 HVT Fan
10.5.25.1 Before Removing the HVT Fan0015-9227
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
10.5.25.2 Removing the HVT Fan0015-9228
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the HVT fan [1].- Cable guide [2]- Connector [3]- Screw [4] 3pc.
F-10-103
10.5.26 Duplex Feed Fan
10.5.26.1 Before Removing the Duplex Feeding Fan0015-8276
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplex feeding front cover. (page 10-14)Reference[Remov-ing the Duplexing Feed Front Cover]
2) Remove the duplex feeding unit. (page 8-49)Reference[Removing theDuplex Feeding Unit]
10.5.26.2 Removing the Duplex Feeding Fan0015-8275
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fan base [3].- Screw [1] 2pc.- Connector [2] 1pc.
[1]
[1]
[1] [2]
[1]
[4]
[3]
[5] [6] [2]
[1] [3]
[1]
[2] [4]
[1]
[2]
[4]
[3]
[4]
Chapter 10
10-31
F-10-1042) Detach the duplex feeding fan [2].
- Screw [1] 2pc.
Be sure that the arrow indicating the direction of air is as indicated whenmounting the duplex feeding fan.
F-10-105
10.5.27 Exhaust Fan
10.5.27.1 Before Removing the Exhaust Fan0015-5155
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).(page 10-22)Reference[Removing the Charger unit]
2) Remove the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
3) Detach the rear cover (lower). (page 10-13)Reference[Removing theRear Cover (Lower)]
10.5.27.2 Removing the Exhaust Fan0015-5156
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the exhaust fan duct [3].- Screw [1] 3pc.- Connector [2] 1pc.
F-10-1062) Detach the exhaust fan [4].
- Screw [1] 2pc.- Connector [2] 1pc.- Fan grid [3]
F-10-107
10.5.28 DC Power Supply Fan
10.5.28.1 Before Removing the DC Power Supply Fan0015-5157
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
2) Detach the left cover (middle). (page 10-14)Reference[Removing theLeft Cover (Middle)]
3) Detach the left cover (lower). (page 10-13)Reference[Removing theLeft Cover (Lower)]
4) Detach the printer power supply PCB. (page 10-24)Reference[Remov-ing Printer Power Supply PCB]
10.5.28.2 Removing the DC Power Supply Fan0015-5162
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the connector [1].
F-10-1082) Detach the DC power supply fan [2].
- Screw [1] 3pc.
[4]
[1]
[2]
[3]
[2]
[1]
[1] [3]
[1][2]
[1]
[2]
[3]
[4]
[1]
Chapter 10
10-32
F-10-109
10.5.29 Fixing Heater Power Supply Cooling Fan
10.5.29.1 Before Removing the Fixing Heater Power Supply Cooling Fan
0015-5163
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
2) Detach the left cover (middle). (page 10-14)Reference[Removing theLeft Cover (Middle)]
10.5.29.2 Removing the Fixing Heater Power Supply Cooling Fan
0015-5166
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the PCB cover [2].- Screw [1] 5pc.
F-10-1102) Open the 2 wire saddles [1].3) Disconnect the 7 connectors [2].4) Detach the fixing heater power supply unit [4].
- Screw [3] 3pc.
F-10-1115) Detach the fixing heater power supply unit cover [2].
- Screw [1] 14pc.
F-10-1126) Detach the duct [2].
- Screw [1] 2pc.7) Detach the fixing heater power supply fan [5].
- Connector [3] 1pc.- Wire saddle [4] 2pc.
F-10-113
10.5.30 Circulation Duct Fan
10.5.30.1 Before Removing the Circulation Duct Fan0015-5167
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left cover (upper). (page 10-12)Reference[Removing theLeft Cover (Upper)]
2) Detach the left cover (middle). (page 10-14)Reference[Removing theLeft Cover (Middle)]
10.5.30.2 Removing the Circulation Duct Fan0015-5169
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness [1] from the harness guide [2].2) Disconnect the connector [3].3) Detach the fixing heater power supply cooling fan [5] together with its
duct.- Screw [4] 3pc.
[1]
[2]
[1]
[1] [1][1]
[2]
[1][2]
[2] [2][3] [3][4]
[1]
[1]
[1] [1]
[2]
[1]
[2] [3][4] [4]
[5]
Chapter 10
10-33
F-10-1144) Disconnect the connector [1].5) Detach the circulation duct fan [3].
- Screw [2] 2pc.
F-10-115
10.5.31 Motor of Main Drive Assembly
10.5.31.1 Before Removing the Main Motor0015-5170
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the rear cover (upper). (page 10-13)Reference[Removing theRear Cover (Upper)]
2) Detach the main controller box cover. (page 10-17)Reference[Remov-ing the Main Controller Box Cover]3) Removing the Right Cover (Upper Rear). (page 10-12)Reference[Re-moving the Right Cover (Upper Rear)]4) Remove the main controller box. (page 4-13)Reference[Removing the
Main Controller Box]5) Detach the right cover (lower rear). (page 10-12)Reference[Removing
the Right Cover (Lower Rear)]
10.5.31.2 Removing the Main Motor0015-5172
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Move the main power switch base [3] to the side.- Screw [1] 2pc.- Clamp [2] 2pc.
F-10-1162) Detach the main motor [2].
- Screw [1] 3pc.
F-10-1173) Disconnect the 2 connectors [1] from the main motor [2].
F-10-118
10.5.32 Fixing Driver Motor
10.5.32.1 Before Removing the Fixing Motor0015-8450
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing theFixing Front Cover]
10.5.32.2 Removing the Fixing Motor0015-5173
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing motor assembly [3].- Connector [1] 2pc.- Screw [2] 3pc.
[2]
[1] [4]
[3] [4] [5]
[1]
[2]
[3]
[1] [1]
[2]
[3]
[1]
[1] [2]
[1][2]
Chapter 10
10-34
F-10-119
10.5.33 Right Door
10.5.33.1 Before Removing the Right Door Unit (Upper)0015-6727
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the right cover (upper rear). (page 10-12)Reference[Removingthe Right Cover (Upper Rear)]
2) Detach the right cover (upper). (page 10-12)Reference[Removing theRight Cover (Upper)]
10.5.33.2 Removing the Right Door Unit (Upper)0015-6717
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Open the right door unit (upper) [1]; then, remove the 1 screw [2] of thedoor strap and open fully the right door unit (upper).
F-10-1202) Detach the connector cover [2].
- Screw [1] 1pc.
F-10-1213) Lift and detach the right door unit (upper).
- Reuse band [1] 1pc.- Connector [2] 1pc.
F-10-122
[1] [2]
[2] [2][3]
[2]
[1]
[1] [2]
[1]
[2]
Chapter 11 MEAP
Contents
Contents
11.1 MEAP.........................................................................................................................................................................11-111.1.1 Checking the Operating Environment. .................................................................................................................................... 11-111.1.2 Setting Up the Network ........................................................................................................................................................... 11-411.1.3 Setting the method to login to SMS......................................................................................................................................... 11-511.1.4 Login to SMS........................................................................................................................................................................... 11-911.1.5 Checking Application List ..................................................................................................................................................... 11-1111.1.6 Starting and Stopping a MEAP Application .......................................................................................................................... 11-1211.1.7 Checking the Platform Information ....................................................................................................................................... 11-1311.1.8 MEAP Specifications............................................................................................................................................................. 11-1411.1.9 Checking the System Information of a MEAP Application with SMS ................................................................................. 11-1511.1.10 Printing the System Information of a MEAP Application................................................................................................... 11-1611.1.11 Reference (Application System Information) ...................................................................................................................... 11-1711.1.12 Installing an Application...................................................................................................................................................... 11-1811.1.13 MEAP Enterprise Service Manager..................................................................................................................................... 11-2111.1.14 Adding a License File .......................................................................................................................................................... 11-2111.1.15 Disabling a License File (suspending a license) .................................................................................................................. 11-2311.1.16 Downloading/Removing an Invalidated License File.......................................................................................................... 11-2511.1.17 Reusable license................................................................................................................................................................... 11-2711.1.18 License for forwarding......................................................................................................................................................... 11-2811.1.19 Uninstalling an Application ................................................................................................................................................. 11-3011.1.20 Changing Login Services ..................................................................................................................................................... 11-3111.1.21 Initializing the Password...................................................................................................................................................... 11-3511.1.22 Creating a Backup for MEAP Application Area, Formatting the Hard Disk, Restoring the MEAP Application Area with the
Backup, Using the SST (Service Support Tool)........................................................................................................................... 11-3611.1.23 Replacing the Hard Disk Drive............................................................................................................................................ 11-3811.1.24 MEAP Safe Mode ................................................................................................................................................................ 11-3811.1.25 Setting HTTP port for MEAP application (level 2)............................................................................................................. 11-4011.1.26 Reference material ............................................................................................................................................................... 11-4311.1.27 Option for exclusive individual measure ............................................................................................................................. 11-47
Chapter 11
11-1
11.1 MEAP
11.1.1 Checking the Operating Environment.0016-1398
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
This section lists the requirements on the operating environment for the maintenance.
Memo:Java Script must be enabled in every environment.
Important:For the following operations in the combined environment of Windows XP and Internet Explorer6, Java2 Runtime Environment Standard Edition 1.3.1 or lateris required. - User registration / edit in SDL - User registration / edit in SSO local device - Use of SSO remote login in SSO
Remote Login of Default Authentication or Simple Device Login (SDL), Remote UI, and Portal ServicesRemote Login of Default Authentication or Simple Device Login (SDL), Remote UI, and Portal Services guarantee operation under the following system environ-ment.
T-11-1
Remote UI (RUI)RUI guarantees operation under the following system environment.
T-11-2
SMSSMS guarantees operation under the following system environment.
Operating System Supported browser
Microsoft Windows 98 SE Microsoft Windows NT Workstation 4.0 SP6a
Microsoft Internet Explorer 5.01 SP2Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows ME Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows 2000 Professional SP3 Microsoft Internet Explorer 5.01 SP2Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows XP Professional / Home Microsoft Internet Explorer 6 GoldMicrosoft Internet Explorer 6 SP1
Mac OS 8.6 - 9.x Microsoft Internet Explorer 5.0 - 5.1.6
Mac OS X 10 - 10.2.4 Microsoft Internet Explorer 5.2.2
Operating System Supported browser
Microsoft Windows 98 SE Microsoft Windows MEMicrosoft Windows NT Workstartion 4.0 Microsoft Windows 2000 Professional Microsoft Windows XP
Microsoft Internet Explorer 5.01 SP2 or laterNetscape Communicator 4.6 or later
MacOS 8.6 or later Microsoft Internet Explorer 5.0 or later
Chapter 11
11-2
T-11-3
SDL and SSO with Local Devoce Authentication (user registration/edit functions)For user registration / edit in SDL and SSO(with Local Authentication), following system requirements must be satisfied.System environment for administrator
T-11-4
System environment for end userT-11-5
SSO domain authentication environmentWindows server for Security Agent to be installed
Security Agent (hereinafter SA) guarantees operation in the following system environment.
T-11-6
Operating System Supported browser
Microsoft Windows 98 SE Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows 2000 Professional Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows XP Microsoft Internet Explorer 6Microsoft Internet Explorer 6 SP1
Operating System Supported browser
Microsoft Windows 98 SE Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows 2000 Professional SP3 Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows XP Microsoft Internet Explorer 6Microsoft Internet Explorer 6 SP1
Operating System Supported browser
Microsoft Windows 98 SEMicrosoft Windows NT Workstation4.0
Microsoft Internet Explorer 5.0.1 SP2Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows ME Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows 2000 Professional Microsoft Internet Explorer 5.0.1 SP2Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Microsoft Windows XP Professional Microsoft Internet Explorer 6 SP1
Hardware
Memory 256MB or more
Hard disk Empty capacity of 15MB or more
CPU Processor more than Intel Celeron 800 MHz corresponding
Chapter 11
11-3
* Construction of SSO domain environment by using Active Directory of Microsoft Windows Server 2003 needs SA of version 2.0.1 or newer, SSO Login appli-cation of version 3.0.0 or newer.
Combination list of the versions of SSO Login application of MEAP device and SAT-11-7
A = SSO basic function supportB = SSO basic function + Multi domain function + LLS cache function supportC = SSO basic function + Multi domain function + LLS cache function support + Server 2003 Active Directory support
Memo:-It must improve in the version of SSO Login application and version of SA when you want to use the function B or C.-The right of access to the domain controller and the right of access to the Windows 2003 DNS are necessary, when the domain authentication is used with SSO.
Important:-The device using SSO authentication and the Windows server on which Security Agent is installed must exists in the same domain.-In the case that Security Agent has been installed in Windows XP Professional SP2, Windows Server 2003 SP1/Server 2003 R2 and Windows Firewall is setenabled, Security Agent (SA.exe) needs to be added as an exceptional program of Windows Firewall. If not being designated a directory of installation, SA.exeis stored in the following directory. C:\Program Files\Canon\SSOPackage\SecurityAgent-In the case that Active Directory has been constructed in Windows Server 2003 SP1/Server 2003 R2 and Windows Firewall is set enabled, TCP port '5678' usedby Security Agent needs to be added in Windows Firewall.
Software OS
Microsoft Windows 2000 Professional SP4
Microsoft Windows 2000 Server SP4
Microsoft Windows XP Professional SP2
Microsoft Windows Server 2003 SP1
Microsoft Windows Server 2003 R2
Corresponding Active Directory
Microsoft Windows 2000 Server SP4
Microsoft Windows Server 2003 SP1 *
Microsoft Windows Server 2003 R2 *
Product Nameof MEAP Device Version of SSO Login Application
Version of SAUS EU AO V1.1.0 V1.2.0 V1.3.0 V1.3.1 V2.0.0 V2.0.1 V3.0.1
iR5020/ iR5020i/ iR6020/ iR6020i
iR5020N/ iR5020i/ iR6020N/ iR6020i
iR5020i/ iR6020i V1.1.0 A A A A A A A
iR2220i/ iR2220N/ iR3320i/ iR3320N
iR2220i/ iR2220N/ iR3320i/ iR3320N
iR2220i/ iR3320i V1.1.0 A A A A A A A
iR C3220/ iR C2620 iR C3220/ iR C2620 iR C3220/ iR C2620 V1.1.1 A A A A A A A
iR 2270/ iR 2870/ iR 3035/ iR 3045
iR 2270 / iR 2870/ iR 3035/ iR 3045
iR 2270 /2870/3035/3045 V1.1.2 A A A A A A AV2.2.7 A A A A B B B
iR85+/ iR8070/ iR105+/ iR9070
iR85+/ iR8070/ iR105+/ iR9070
iR85+/ iR8070/ iR105+/ iR9070
V1.1.3 A A A A A A AV2.2.7 A A A A B B B
iR 5570/ iR 6570 iR 5570 / 6570 iR 5570 / 6570 V2.0.0, V2.2.9
A A A A B B B
iR C3170U/ iR C3170i iR 3170C/ iR 3170Ci/ iR C2570/ iR C2570i
iR C3170/ iR C3170i/ iR C2570/ iR C2570i
V2.2.6 A A A A B B B
iR C5870U/ iR C6870U iR 5870C/ iR 5870Ci/ iR 6870C/ iR 6870Ci
iR C5870/ iR C5870i/ iR C6870/ iR C6870i
V2.4.0 A A A A B B B
iR7086/ iR7095/ iR7095 Printer/ iR7105
iR7086/ iR7095/ iR7095 P/ iR7105
iR7086/ iR7095/ iR7095 P/ iR7105
V2.5.0 A A A A B B B
iR C5180i/ iR C4580i/ iR C4080i
iR C4080/ iR C4080N/ iR C4580/ iR C4580N/ iR C5180/ iR C5180N
iR C4080/ iR C4080N/ iR C4580/ iR C4580N/ iR C5180/ iR C5180N
V3.0.0 A A A A B C C
imagePRESS C1 imagePRESS C1 imagePRESS C1 V3.1.0 A A A A B C CiR C2880/ iR C3380 iR C2880 / C3380 iR C2880 / C3380 V3.2.0 A A A A B C CiR3025/ iR3030/ iR3035/ iR3045
iR3025/ iR3030/ iR3035/ iR3045
iR3025/ iR3030/ iR3035/ iR3045
V3.4.1 A A A A B C C
iR 5055/ iR 5065/ iR 5075 iR 5055/ iR 5065/ iR 5075 iR 5055/ iR 5065/ iR 5075 V3.5.0 A A A A B C C
Chapter 11
11-4
BrowserThe following combinations of operations are guaranteed for the access from Web browser to MEAP device.
T-11-8
11.1.2 Setting Up the Network0016-1400
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To allow a MEAP device to accept accesses through the network, for example you operate a device with SMS, the On option must be selected on Use HTTP screen.The option is selected by default. The setting can be changed on the control panel of the MEAP device.
1) Make the following selections: Ad Func button > System Settings button> Down-arrow button.
Memo:If the System manager ID and system password have already been assigned, ID Entry dialog appears after System Settings button is pressed. Enter the systemmanager ID and the password, and click ID key to go into System Management Mode.
F-11-1
2) Make the following selections: MEAP Settings button > Use HTTP button> On button > OK button .
OS Supported Browser
Microsoft Windows 98SEMicrosoft Windows NT Workstation 4.0 SP6a
Microsoft Internet Explorer 5.01 SP2,Microsoft Internet Explorer 5.5 SP2,Microsoft Internet Explorer 6 SP1
Microsoft Windows ME Microsoft Internet Explorer 5.5 SP2,Microsoft Internet Explorer 6 SP1
Microsoft Windows 2000 Professional SP3 Microsoft Internet Explorer 5.01 SP3,Microsoft Internet Explorer 5.5 SP2,Microsoft Internet Explorer 6 SP1,
Microsoft Windows XP Professional Microsoft Internet Explorer 6 SP1,
Chapter 11
11-5
F-11-2
Memo:When using SSL, set [Use SSL] ON.(This setting is also applied to the SSL setting of RUI. Same is true in the case of setting SSL ON on the side of RUI.)
Setting [Use SSL] ON displays the message dialogue 'Changes effective after the main power switch is turned OFF and ON' . Press [OK].
F-11-3
3) Press Done button as many times as necessary until the Basic screen appears.
4) Turn off the device's main power; wait for 10 sec, and then turn the power back on.
- The setting [Use HTTP] is not actually enabled/disabled until you have turned off and then on the device's main power switch.- You cannot make a connection through a proxy server. If a proxy server is in use, enter the IP address of the MEAP device in the Exceptions field for thebrowser. Open Internet Options dialog of Internet Explorer and select Connections tab, LAN Settings button, Use a proxy server option, and Advanced buttonof Proxy server group. Proxy Settings dialog will opens. The Exceptions field is in the dialog. As network settings vary among environments, consult thenetwork administrator.- If Cookie and JavaScript are not enabled in the Web browser, you will not be able to use SMS.- To type text using the Web browser, use the characters compatible with the MEAP device's touch panel display. The MEAP device may not properly recognizesome characters.- When [se SSL] is made available, it is necessary to set the key and the certificate necessary for the SSL communication. Set the key and the certificate by SSLwith [Certificate Settings] that exists in [System Settings] > [Network Settings] > [TCP/IP Settings] on the iR device.
11.1.3 Setting the method to login to SMS0016-1401
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
SMS Installer Service, which is used to login SMS includes Password Authentication and Remote Login Service Authentication (henceforce: RLS Authentication).Password Authentication is an authentication method only by password. RLS Authentication is an authentication method using SDL / SSO by ID and password.Either or both of the authentication methods can be enabled by changing the setting.
Memo:If Default Authentication is selected as the device authentication method, 'RLS Authentication' is not selectable as SMS Login method. Also, if 'RLSAuthentication' is selected, the device authentication method (Default Authentication, SDL, SSO) cannot be changed.
Setting of login method to SMS (Start/Stop) must be made after logging-in by the other login method. In other words, setting for Start/Stop of Password Authenti-cation is made after logging-in with RLS Authentication, and setting for Start/Stop of RLS Authentication is made after logging-in with Password Authentication.
Chapter 11
11-6
The table below shows the setting methods for each combination of login method and Start/Stop.T-11-9
When only RLS Authentication is enabled, there may be a case you cannot login to device for the following reasons. - Authentication server down - Disconnection with authentication server due to network failureIn these cases, boot the device as MEAP SAFE mode from device service mode.By booting the device as MEAP SAFE mode, login to SMS becomes available as Default Authentication is enabled. After login to SMS, set RLS Authenticationas Started, return the device to normal mode, and then login by RLS Authentication.
Setting for login by Password Authentication1) In order to make a setting for login by Password Authentication, you need to login by RLS Authentication. Therefore, login by RLS Authentication.
Login screen (In case authentication method is SSO)
F-11-4
2) Select 'System Management' tab > 'Utility' tab > 'Application Management Function' tab.
F-11-5
3) In order to enable login by Password Authentication, tick SMS Installer Service (Password Authentication) radio button and then click [Start]. On the other hand,in order to disable login by Password Authentication, clear the tick of SMS Installer Service (Password Authentication) radio button and click [Stop].
Start RLS Authentication Stop RLS Authentication
Start Password Authentication Login available with either method Login available only with Password Authentication
Stop Password Authentication Login available only with RLS Authentication Setting unavailable
Chapter 11
11-7
F-11-6
4) Logout once and login again to check to see that the setting is applied properly. In case the setting is changed from 'Stop' to 'Start', login screen that was not seenbefore is displayed. In case the setting is changed from 'Start' to 'Stop', access to login screen leads to the screen below and login becomes unavailable.
Login error screen
F-11-7
Setting for login by RLS Authentication1) In order to make a setting for Login by RLS Authentication, you need to Login by Password Authentication.
Login screen by Password Authentication
F-11-8
2) Select 'System Management' tab > 'Utility' tab > 'Application Management Function' tab.
Chapter 11
11-8
F-11-9
3) In order to enable Login by RLS Authentication, tick SMS Installer Service (Remote Login Service Authentication) radio button and then click [Start]. On theother hand, in order to disable login by RLS Authentication, clear the tick of SMS Installer Service (Remote Login Service Authentication) radio button and click[Stop].
F-11-10
4) Logout once and login again to check to see that the setting is applied properly. In case the setting is changed from 'Stop' to 'Start', login screen that was not seenbefore is displayed. In case the setting is changed from 'Start' to 'Stop', access to login screen leads to the screen below and Login becomes unavailable.
Login error screen
Chapter 11
11-9
F-11-11
11.1.4 Login to SMS0016-1402
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Login by Password Authentication1) Access SMS from the browser of the PC connected to the network on which the MEAP device operates. URL: http://<MEAP Device IP address>:8000/sms/ Ex.)http://172.16.188.240:8000/sms/
Memo:- The default password is "MeapSmsLogin." (The password is case-sensitive.)- When you want to change the display original language, change in the box in the right of the screen. This setting is not affect by the setting of the language ofthe device.
F-11-12
2) The following screen appears if the password has been changed by the user's system administrator. If so, check with the system administrator for the new pass-word. Keep in mind that there is no special password offered for service work.
Chapter 11
11-10
F-11-13
Login by RLS Authentication1) Access SMS by RLS Authentication from the PC browser on the same network as the MEAP device. URL: http://<IP address of MEAP device>:8000/sms/rls/ Ex.) http://172.16.188.240:8000/sms/rls
Memo:- In case the device authentication method is SSO and login to domain, enter User Name, Password, and Login Destination registered in Active Directory, andclick 'Log in'.- In case the device authentication method is SDL or SSO and login to 'this device', enter User Name and Password registered in the device and click 'Log in'.
In the case the device authentication method is SSO
F-11-14
In the case the device authentication method is SDL
Chapter 11
11-11
F-11-15
11.1.5 Checking Application List0016-1403
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The page of Application List is designed to show resources arranged according to applications. The page gives you a good idea of how much of the device's memoryis being used by the applications (both in absolute and relative terms) as well as how much memory still remains. Check this page before adding an application.
The information is collected from the manifest (headers) - in other words, the size of a resource represents the size as it is declared by the application in question,not necessarily the size of resources actually used by the application. The items of information include the following: - hard disk - memory - thread - socket - file descriptor
You will not be able to install an application if the size of the remaining memory falls short of the size declared by the application. Moreover, the specificationshave been designed so that an application will not be able to start up if there is a shortage of memory for any of the foregoing items (i.e., memory, thread, socket,file descriptor). To find out if there is enough memory, go through the following steps:
1) Log in to SMS.
2) Click Application List tab.
3) Check the displayed information:
a. Information on Applications - Name (of the application) - Installation (date) - Application ID - Status - License - Resources Used
b. Resource Information - Amount Used - Remaining - Percent Used
Chapter 11
11-12
F-11-16
11.1.6 Starting and Stopping a MEAP Application0016-1404
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Log in to the SMS.
2) Click 'Application List'.
3) Click the radio button of the MEAP application in question, and click 'Start' or 'Stop'.
F-11-17
4) Check to see that the status of the MEAP application in question is either "Started" or "Stopped."
Chapter 11
11-13
F-11-18
11.1.7 Checking the Platform Information0016-1405
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can check the versions of MEAP Contents, MEAP Specifications, and Java Virtual Machine of the device.
Some applications may not be installed to some MEAP devices of specific specifications. (See 'MEAP Specifications').
1) Log in to SMS.
2) Click System Management tab.
F-11-19
3) Click System Info tab.
Chapter 11
11-14
F-11-20
11.1.8 MEAP Specifications0016-1406
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
What is MEAP Specifications (MEAP Spec Version)?MEAP Specifications is one of the information required to judge whether MEAP applications can be operated or not. With MEAP Specifications, you can preventan application that uses a specific function of device from being installed onto the device that does not have the function.
About NameMEAP Specification is shown as 'MEAP Specifications' in the screen to check the version on the side of device that supports MEAP (counter confirmation button)and MEAP platform (SMS). On the other hand, in the manifest file of MEAP application, it is shown as 'MeapSpecVersion' (described in the same way in the SDKdocument)(Note) 'MEAP Specifications' hereafter in this document.
MechanismMEAP platform judges whether MEAP applications can be operated on it using on the 2 information below: - Device Specification ID - MEAP Specifications
Device Specification ID shows information such as the original functions of MFP (including print, scan, and copy), and one that differs by model such as maximumcopy number, thus each model has a different ID. (It is easy to determine the IDs for this reason.) MEAP application declares 1 or more Device Specification IDrequired for its execution. Declaration of multiple Device Specification IDs means that the application is operable in all the models declared. Upon installation ofMEAP application in (using) SMS or MEAP Enterprise Service Manager, matching of Device Specification ID is executed on the side of MEAP platform machine.The machine which doesn't support the ID declared by the application rejects installation of such an application.
Meanwhile, MEAP Specifications shows other information than defined by Device Specification ID above, including network and security. Thus each model doesnot always have the same version.
MEAP application declares 1 or more MEAP Specifications required for its execution. Declaration of multiple Device Specification IDs means that the applicationis operable in all the environments declared. Upon installation of MEAP application in SMS or MEAP Enterprise Service Manager, matching of MEAP Specifica-tions is executed on the side of MEAP platform machine. The machine which doesn't support the version declared by the application rejects installation of such anapplication.
MEAP Spec Version for each modelT-11-10
Product Name USA EUR OCE SPL KOR Initial MEAPSpecVer Change informationiR 6020 Y Y Y Y -iR 5020 Y Y Y Y -iR 3320 Y Y Y Y -iR 2220 Y Y Y Y -iR C3220 Y Y Y Y - 1, 2, 3iR C2620 Y Y Y Y - 1, 2, 3iR 4570 Y Y Y Y Y 5 5, 6, 7 (System v30.xx later)iR 2870 Y Y Y Y Y 5 5, 6, 7 (System v30.xx later)iR 2270 Y Y Y Y - 5 5, 6, 7 (System v30.xx later)iR 3570 Y Y Y Y Y 5 5, 6, 7 (System v30.xx later)iR85+ Y Y Y - -iR 8070 Y Y Y Y - 5 5, 6, 7 (System v10.xx later)
Chapter 11
11-15
* Due to the change in I/F specifications, these models support '5' only.
T-11-11
MEAP Spec Version
11.1.9 Checking the System Information of a MEAP Application with SMS0016-1407
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Log in to SMS.
2) Click System Management tab.
3) On System Management screen, click System Info tab.
4) Click Details button.
iR 105+ Y Y Y Y - 5 5, 6, 7 (System v10.xx later)iR 9070 Y Y Y Y - 5 5, 6, 7 (System v10.xx later)iR 6570 Y Y Y Y Y 5, 6 5, 6, 7, 9 (System v20.xx later)iR 5570 Y Y Y Y Y 5, 6 5, 6, 7, 9 (System v20.xx later)iR C3170 Y Y Y Y Y 5, 6, 7iR C2570 - Y Y Y Y 5, 6, 7iR 7105 Y Y Y Y Y 5, 6, 7iR 7095 Y Y Y Y Y 5, 6, 7iR 7086 Y Y Y Y - 5, 6, 7iR 7095P Y Y Y Y - 5, 6, 7iR C6870 Y Y Y Y Y 5, 6, 7iR C5870 Y Y Y Y - 5, 6, 7iR C5180 Y - Y Y Y 5, 6, 7, 9, 10, 11 5, 6, 7, 9, 10, 11, 13, 14, 15 (System v50.xx later)CLC5151 - Y - - - 5, 6, 7, 9, 10, 11, 13, 14, 15 (System v50.xx later)iR C4580 Y - Y Y Y 5, 6, 7, 9, 10, 11 5, 6, 7, 9, 10, 11, 13, 14, 15 (System v50.xx later)CLC4040 - Y - - - 5, 6, 7, 9, 10, 11, 13, 14, 15 (System v50.xx later)iR C4080 Y Y Y - - 5, 6, 7, 9, 10, 11, 13, 14, 15 (System v50.xx later)imagePRESS C1 Y Y Y Y Y 5, 6, 7, 9, 10, 11iR C3380 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13iR C2880 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13iR 3025 Y Y Y Y - 5, 6, 7, 9, 10, 11, 13iR 3045 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13iR 3035 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13iR 3030 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13iR 5055 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13iR 5065 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13iR 5075 Y Y Y Y Y 5, 6, 7, 9, 10, 11, 13
MEAP Spec Version Description 1 MEAP basic function 2 MEAP Spec Version 1 function and SSL/TSL + Proxy 3 [Reserved] 5 MEAP Spec Version 1 function and CPCA V2 + ERS (Error Recovery Service) + New SSL/TSL6 [Reserved]7 MEAP Spec Version 5 function and Compact PDF + OCR PDF(Text Searchable) + USB-Host(Buffering of Interrupt Transfer)9 [Reserved]
10 MEAP Spec Version 5 function and USB-Host(Exception + ClearFeature + SetFeature + HotPlug) + WINS address acquisition using MIBAgent + TimerService + SSL client authentication
11 MEAP Spec Version 5 function and AMS 13 MEAP Spec Version 5 function and J2ME1.1 Support + Encrypted PDF + Trace and smooth PDF + CTK2.0 14 Device signature PDF15 IMI + ERS (API addition for IMI)
Product Name USA EUR OCE SPL KOR Initial MEAPSpecVer Change information
Chapter 11
11-16
F-11-21
5) When the following status information of MEAP applications (including the system application) appears in a different window, copy and paste all informationto create an attachment (text information) for preparing a problem report. You can also use this function whenever you want to check the status of any particularapplication.
F-11-22
11.1.10 Printing the System Information of a MEAP Application0016-1408
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Make the following selections: Additional Functions button > System Settings button> the down-arrow button.
Memo:If the System manager ID and system password have already been assigned, ID Entry dialog appears after System Settings button is pressed. Enter the systemmanager ID and the password, and click ID key.
Chapter 11
11-17
F-11-23
2) Make the following selections: MEAP Settings button > Print System Information button >Yes button.
F-11-24
3) Press Done button as many times as necessary until the Basic screen appears.
4) Turn off the MEAP device's main power; wait for 10 sec, and then turn the power back on.
Important:The previous version of printing function for MEAP application status information (system information) was depended on PDL. However, current version offunction is not dependent on PDL. So even device for which PDL is not available can print it. (Since iRC3220)
11.1.11 Reference (Application System Information)0016-1409
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can check all applications installed to the device at a glance with the MEAP application status information and, thus, it is important for you to provide it whenyou are reporting a problem.The following items of information will be indicated or printed for individual applications:
Memo:The system information shown on the screen and the system information printed in the MEAP device's user mode are exactly the same.
T-11-12
Chapter 11
11-18
Application System Information
Application NameIt is the name (bundle-name) declared in a statement within the application program. It may not necessarily be identical to the name of the program.
Application ID/System Application NameIn the case of a system application, it will be the file name. If a general application, it is the application ID (application-ID) declared in a statement within the ap-plication program. Within the device, the applications are set apart by means of their application IDs.
Application VersionIt is the version of the application (bundle-version) declared in a statement within the application program.
StatusIt indicates the status of the application in question; specifically,Installed: the application has been installed.Active: the application is being in use.Resolved: the application is at rest.
Installed OnIt indicates the date on which the application was installed.
VendorIt is the name of the vendor that developed the application, and is the name (bundle-vendor) declared in a statement within the application program.
License StatusIt indicates the status of the license; specifically,None: no license is needed.Not Installed: no license has been installed.Installed: the appropriate license has been installed.Invalid: the license has been invalidated.Overlimt: the license has been used beyond its permitted limit.
License Expires AfterIt indicates the date after which the license expires. If the status of the license is 'none', this item will not be printed.
License Upper LimitIt indicates the limit imposed on individual counter readings. If the status of the license is 'none', this item will not be printed.
Counter ValueIt is the current counter reading of a specific counter. If the status of the license is 'none', this item will not be printed.
Maximum Memory UsageIt indicates the maximum amount of memory that the application uses. It is the amount (maximum memory usage) declared in a statement within the applicationprogram, and is expressed in kilobytes.
Registered ServiceIt is a list of services that have been registered by the application with the MEAP framework. Some services may not have printable data.
11.1.12 Installing an Application0016-1410
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Important:- To install an application, the user needs to use the following URL when accessing the license control system to obtain a license file. In doing so, he/she needsto register the license access number of the application and the serial number of the device.http://www.canon.com/meap/ -Maximum 20 applications can be installed (In iR5160/iR6060/iR2250/iR2850/iR3350, one is the portal service already installed at the time of shipment fromthe factory)-The following are the resource amounts assured for each device in the operation of one MEAP application. These values are for reference purpose only, thereforethe unused resource of SMS needs to be checked at the time of installation of MEAP application.The displayed values of SMS resource may be larger than the followings since the actual values vary according to the log-in service (authentication function)selected by users and the configuration (future models).
Application Name: C-Cabinet Gateway for MEAPApplication ID/System Application Name: 03a46668-63e4-4636-9cbb-492b6cef05d5Application Version: 1.0.0Status: ResolvedInstalled on: Tue Oct 21 14:00:11 GMT+09:00 2003Vendor : Canon Inc.License Status : InstalledMaximum Memory Usage : 1024Registered Service :
Chapter 11
11-19
T-11-13
*20MB for 512MB model, 30MB for 768MB model.- As for memory, check the available resource when starting up the application. For other resources other than memory, check them when installing.- Some applications call for a specific set of conditions for installation. For details, see the User's Guide that comes with the individual applications.
1) Long on to SMS.
2) Click Install tab.
F-11-25
3) Check that Install Application/License page appears.
4) Click Browse button, and select the application file and the license file of the application; then, click OK button.
Memo:Application File: identified by the extension "jar".License File: identified by the extension "lic".
Product Name HDD Memory Thread Socket File Description
iR5020/iR6020/iR2220/iR3320 300MB 20MB 128 48 42iRC2620/iRC3220 400MB 20MB 128 48 42iR2270/iR2870/iR3570/iR4570/iR85/iR8070/iR6570/iR5570 400MB 20MB 128 48 42iRC3170/iRC2570 400MB 20MB 128 48 42iR7086/iR7095/iR7105 400MB 20MB 128 48 42iRC4080/iRC4580/iRC5180 Initial MEAP Spec Ver 1024MB 20MB 128 48 42
Change Information 1024MB 30MB 128 128 128imagePRESS C1 1024MB 20MB 128 48 42iRC2880/iRC3380 1024MB 20MB 128 48 42iR3025/iR3030/iR3035/iR3045 400MB 20/30MB* 128 48 42iR5055/iR5065/iR5075 1024MB 20MB 128 48 42
Chapter 11
11-20
F-11-26
5) See the message "Installing...Please wait a moment."
F-11-27
Important:- You cannot install only the license.
- You will not be able to install the application without using the appropriate license. Be sure to select its license file.
- If you are adding a license to an existing application, see 1.3.10 Adding a License File.
- If you are updating an existing application, stop the application; then, install the new application or its license file. You will not be able to update an applicationwhile it is running.
6) Check the contents of the Confirm page; then, click OK button.
F-11-28
Chapter 11
11-21
7) Some applications show a screen to indicate the terms of agreement. Read the terms, and click OK.
8) Check the message "Installing...Please wait a moment." appears, beginning the installation.
9) Check Application List page appears when the installation is completed.
Important:To use the application that you have just installed, you must make sure that the application status is Started.
11.1.13 MEAP Enterprise Service Manager0016-1412
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
OutlineMEAP Enterprise Service Manager is the PC application utility to perform batch installation, unistallation and management of MEAP application and license filesrequired for installation of applications, on several MEAP-available devices on network. The main targets are system administrators in big companies and CANON service engineers (end users of devices do not use).It is used when customized applications delivered to a certain company needs to be managed collectively.Previous SMS can manage only one device at a time. This utility reduces the management cost of devices and TCO.
Major functionsDiscovery of devices available for MEAPDiscovery of devices available for MEAP on networkStorage of the serial number list of discovered deviceInstallation of application and license fileManagement of application (starting / stopping)Uninstallation of applicationOthers
System configurationMEAP Enterprise Service Manager (MEAP ESM) functions in combination with DIS (DSL Installer Service) installed on the MEAP platform side of the device.This system can be used only for MEAP-available device with appropriate DIS installed.
(*) When using this system on the firmware for version upgrading on October 2003 or older, version upgrading of the system software on the field device is nec-essary.
The versions available for ESM are as follows:iR5160 / iR6020: System v54.02 or newer, MEAP Contents v53.07 or neweriR2220 / iR3320: System v33.01 or newer, MEAP Contents v33.02 or newerOther products: Available from the initial version
When installing MEAP Enterprise Service Manager (MEAP ESM) of master CD on PC, Microsoft '.NET Framework' v1.0 or v1.1 is necessary. The user shoulddownload it from the Web site of Microsoft.
11.1.14 Adding a License File0016-1413
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Log on to SMS.
2) On Application List, click the name of the application to which you want to add a license file.
Chapter 11
11-22
F-11-29
3) Check appears.
4) On Application/License Information page, click License Management button.
F-11-30
5) Click Browse button, and select the license file you want to install.
Chapter 11
11-23
F-11-31
6) Click Install button.
F-11-32
7) Check the content of the confirmation page, and click OK button.
11.1.15 Disabling a License File (suspending a license)0016-1415
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Important:- To invalidate (or suspend) a license, you must first stop the application in question.- Once suspended, the status of the license will be 'Not Installed', and its application will no longer be available for use.- You can later restore a suspended license file as long as you are doing so on the same iR, the device with the same device serial number.- When replacing the device due to lease up or trouble, use the license for forwarding (See 'License for forwarding').
1) Stop the application you want to uninstall on Application List page.
Chapter 11
11-24
F-11-33
2) Click the name of the application that you want to disable.
F-11-34
3) License File Management page appears. On Application/License Information page, click License Management button.
Chapter 11
11-25
F-11-35
4) Click Disable button.
F-11-36
5) Click OK.
11.1.16 Downloading/Removing an Invalidated License File0016-1416
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You must remove the invalidated license file before uninstalling an application. If re-installation is a possibility, you may download the license file to a PC forstorage. To download or delete a license file, first disable it.
Important:- Once you have removed an invalidated license file, you will no longer be able to download it form the MEAP device.
1) Login to SMS.
2) Application List page appears.
3) On Application List page, click the name of the application you want.
Chapter 11
11-26
F-11-37
4) Check Application/License Information page appears.
5) On Application/License Information page, click License Management button.
F-11-38
6) License File Management page appears. To download, click Download button.
Chapter 11
11-27
F-11-39
7) When you have selected Download button, specify where you want to store the file by following the instructions on the screen.
8) To delete, click Delete button.
F-11-40
9) Check the confirmation page appears.
10) Click OK button.
Important:- Without the license file, an application cannot be reinstalled even to the MEAP device that the application had been installed last time. Download and savethe license file before deleting the application.
11.1.17 Reusable license0016-1417
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Reinstallation was not able to perform for all license files. When reinstalling, Disable License file should be downloaded (see 'Disabling a License File' and 'Down-loading / Removing an Invalidated License File' in this manual) or a license for reinstallation should be obtained from LMS, before reinstallation.This specification aims to prevent misuse of applications.To increase convenience of users, only application with unlimited validity date and application counter (e.g. Portal Service, SDL, SSO) has been made to be able
Chapter 11
11-28
to install as many times as needed by the same license file. This kind of license is called 'Reusable license'.
Memo:For devices for System version of 33.01, 54.02 (iR 2220 series / iR5020 series) or older, version upgrading is required. It is already installed in the model withiR C3220 or newer.
11.1.18 License for forwarding0016-1418
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When the device is replaced due to lease up or trouble, it is possible to continue using the current license information of MEAP application by forwarding it to anew device. The license is forwarded by CE because the hidden page of SMS is used.1) Log in to SMS, stop the application to be forwarded (see 'Starting and Stopping a MEAP Application' in this manual).
F-11-41
2) Move to the download page of license forwarded for the device as sender (http:// IP address of device: 8000/sms/ForwardLicense).
F-11-42
3) Specify the application to be forwarded.
F-11-43
Chapter 11
11-29
4) Click 'Disable' at Create Transfer License File.
F-11-44
5) The screen to check invalidation of the license is displayed. Click 'OK',
F-11-45
6) Icon of license file for forwarding is displayed in the box of license file downloading. Click 'Download'.
F-11-46
7) The dialogue 'File Download' is displayed. Click 'Save'.
Chapter 11
11-30
F-11-47
8) Specify the download destination, click 'Save'.
F-11-48
9) After downloading the license file for forwarding, click 'Delete' to display the confirmation screen and click 'OK' to delete the file (in consideration of breakageof license for forwarding, deleting disabled license can be executed after all steps have been completed).
F-11-49
10) Log out of SMS.11) Ask the sales company to issue a license for forwarding.
Memo:When requesting issuance of license for forwarding, inform the sales company of the name of product name and serial No. of the device as sender, and of thename of product name and serial No. of the forwarding destination.
12) Install application using the license for forwarding issued by the sales company.
11.1.19 Uninstalling an Application0016-1420
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Chapter 11
11-31
1) Log on to SMS, and click 'Application List' tab.
2) Check 'Application List' page appears.
3) On the application list, select the radio button of the application you want to uninstall, and click 'Uninstall' button.
Memo:Dimmed Uninstall button shows that the selected application cannot be removed.
F-11-50
4) Check the screen to make sure that what is shown is the application you want to uninstall; then, click OK button.In response, the system runs an uninstall sessions.
Important:- The status of the license must be 'Not Installed' or 'Unnecessary' for its application to be uninstalled. As necessary, go to License File Management page, anddisable the license file before starting to remove it.- A license file may be invalidated only when its application is not active.- If the application you are uninstalling is associated with another application, a message will appear to indicate that the package exported by the application willno loner be available. Uninstalling such an application may also disable its associated applications.
11.1.20 Changing Login Services0016-1421
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Login Service OverviewThe login service is used to authenticate users who logs in to a MEAP device. You can change login services or uninstall them using System Management site.
At time of shipment, the login service offers the following 3 modes of authentication:
- Default authentication - SDL (Simple Device Login) - SSO (Single Sign-On)
Important:- To set SDL, the registered information in SDL and the registered user data (Department ID and Password) in Department ID Management of the machine haveto match.- To set up SDL or SSO, Department ID Management must be set to Off in advance. To use SDL and Department ID Management simultaneously, setDepartment ID Management to On after switching the login service to SDL. - If SSO is set as the login service, NetSpot Accountant is necessary for using Department ID Management.- If SSO is set, you cannot use an optional card reader. - To set to SSO, first adjust the current time for the PC where Active Directory is running, the iR, and the PC where users log on. If there is more than a 30-minute difference among them, an error occurs at logon. - If SSO or SDL is set as login service, it takes time until the iR is ready to start up.- When the SEND function is used in the environment of SDL and SSO, it is necessary to set each user's mail address to transmit E-mail. When the mail addressis not set, E-mail cannot be transmitted. However, when i-Fax is transmitted, the mail address set to the device is used.
Outline of Default Authentication
Chapter 11
11-32
In this mode of authentication, you will be using Department ID Management or you will not be using any authentication mechanism. If you enable the DepartmentID Management in the MEAP device's Additional Functions mode, the user can use the device only when he/she enters an ID number (a 7-character ID and pass-word) that has been registered from the device's touch panel display or through Remote UI.
Outline of SDL (Simple Device Login)In this mode of authentication, you will be operating on a MEAP device on its own. You will store user information to the MEAP device's memory by accessingthe device through a Web browser. SDL offers the following functions:
a. it brings up the Login screen on the MEAP device's touch panel display for user authentication.
b. it brings up the Login page when you access the MEAP device from Web browser to manage the numbers of printed and scanned sheets for each department IDworking with the department ID management function. it operates in conjunction with the group ID control mechanisms to keep track of the number of printpages or scan pages according to group IDs.
c. it enables register/editing of user authentication information through a Web browser.
F-11-51
Outline of SSO (Single Sign-On)This is the log-in service that can be operated on the domain of Active Directory environment network or at iR device. The following are the user authenticationsystems. - Domain Authentication - Local Device Authentication - Domain Authentication + Local Device Authentication
- The three user authentication systems can be changed at Web browser (See 'Setting the User Authentication System' on MEAP Administrator Guide).- The default setting is 'Domain Authentication + Local Device Authentication'. To increase security, set 'Domain Authentication' as user authentication systemor change the user name and password of the administrator of Local Device Authentication from the default ones, just after starting to use SSO.
Domain AnthenticationThis is the authentication of the domains on network simultaneously with log-in to iR device, in combination with the domain controller on Active Directory envi-ronment network. It authenticates up to four domain users (multi domain) with trusts as well as the domain with iR device installed. Users select the domain nameof log-in destination when they log in.Optional NetSpot Accountant or imageWARE Accounting Manager enables analysis / management of the usage of iR device.
Local Device AnthenticationThis is the user authentication used for only iR device itself. The users to be authenticated is registered / managed by the database of iR device. The method ofregistration / management is the same as the one for SDL. The log-in destination is [this device].
Domain Authentication + Local Device AnthenticationThis is the user authentication system with the functions of both 'Domain Authentication' and 'Local Device Authentication'. Domain Authentication is useful toauthenticate the users registered / managed by Active Directory, and Local Device Authentication is for authentication of the temporary users being not able to beadded to Active Directory. In the case that any trouble of domain controller or Security Agent occurs, using Local Device Authentication enables emergency actionuntil recovery. In the following example, Domain A user with iR installed and Domain B having trusts with Domain A, and also the users registered in iR device itself can beauthenticated. Users select the login destination (domain name or [This Device]) when they log in.
Chapter 11
11-33
F-11-52
- Optional NetSpot Accountant or imageWARE Accounting Manager is necessary to use Domain Authentication and department ID managementsimultaneously. When Domain Authentication is set without combination with NetSpot Accountant or imageWARE Accounting Manager, log-in is impossible.Therefore, department ID management should not be 'ON'. If department ID management is set to 'ON' while using Domain Authentication and log-in becomesimpossible, change the log-in service to Default Authentication and turn department ID management to [OFF].- For combination with NSA / iWAM, it is necessary to set the user with administrative privilege of the domain on the SA service account.- When the print count and scan count for each department ID needs to be managed in conjunction with Local Device Authentication and department IDmanagement, turn department ID management to [ON]. To use simultaneously Local Device Authentication and department ID management, the informationregistered with Local Device Authentication should be matched with the user information of department ID management (department ID and password).- The user information registered by SDL and the one by Local Device Authentication are managed separately in the iR device. The user information registeredin one system is not reflected to the other. - The card reader for optional control card cannot be used for Local Device Authentication. When using the card reader for control card, set SDL.- Security Agent is necessary only for Domain Authentication.- Security Agent should be installed on the computer in the domain with iR device installed.- Installation of Security Agent is included in MEAP Administrator CD-ROM.
Operating EnvironmentThe operation is guaranteed for SDL or SSO if the system environment is in keeping with the following requirements:
SDL (registering/editing user information)a. Operating System and Supported Browsers
T-11-14
Important:- If you use Internet Explorer 6 on Windows XP, you will need Java 2 Runtime Environment Standard Edition 1.3.1.
SSOTo use SSO, you must have a Widows server to which Active Directory has been installed as well as Security Agent.
1) PC for hosting Security Agenta. Supported OS
T-11-15
Operating System Supported browser
Windows 98 SE Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Windows 2000 Professional SP3 Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Windows XP Microsoft Internet Explorer 6Microsoft Internet Explorer 6 SP1
Operating System
Microsoft Windows 2000 Professional
Microsoft Windows 2000 Server
Microsoft Windows XP Professional
Microsoft Windows Server 2003
Domain A Domain B
NetSpotAccountant
Security AgentDomain Controller(Active Directory)
Domain A User Domain B UseriR
Domain Controller(Active Directory)
Chapter 11
11-34
When using SA on WindowXP SP2, it is necessary to exclude Security Agent from the targets of firewall at the setting of the firewall.
b. Others Access right to Windows 2000 domain Name System (DNS)Access right to domain controller
For combination with NetSpot Accountant / iW Accounting Manager, and department ID management is turned on to use it, it is necessary to set the user withadministrative privilege of the domain on the SA service account.
2) Client PC (if access from Web browser to MEAP device is desired)
a. Operating System and Supported BrowsersT-11-16
b. Others Access right to Windows 2000 Domain Name System (DNS)Access right to Domain Controller Client
Steps to Change Login Services
1) Make the following selections: System Management > Enhanced Sys. App.
F-11-53
2) A page will appear showing the various selections you can make for the login service. Select the radio button of the login service mode you want to use; then,click Select button.
Operating System Supported Browsers
Windows 98 SE Windows NT Workstation 4.0 SP6a
Microsoft Internet Explorer 5.01 SP2Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Windows ME Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Windows 2000 Professional SP3 Microsoft Internet Explorer 5.01 SP3Microsoft Internet Explorer 5.5 SP2Microsoft Internet Explorer 6 SP1
Windows XP Professional Microsoft Internet Explorer 6 SP1
Chapter 11
11-35
F-11-54
3) When login service application you have selected turns to Start after Restart, turn off the device's main power, and turn it back on after 10 seconds.
F-11-55
11.1.21 Initializing the Password0016-1422
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Get the switch license for initializing the password.Request the support of the regional headquarters of the Canon for switch license for initializing the password presenting the device serial number.
2) Click Login button leaving Password field blank or entering incorrect password. The Return to install Password Settings area appears. Click Browse buttonand select the switch license file prepared in advance.
Chapter 11
11-36
F-11-56
3) When you click Initialize button, the confirmation message appears. Click OK button. Then Login page opens. Enter the default password 'MeapSmsLogin' tolog in. The password is case-sensitive.
If you click Cancel button, the Login page opens without initializing the password.
11.1.22 Creating a Backup for MEAP Application Area, Formatting the Hard Disk, Restoring the MEAP Application Area with the Backup, Using the SST (Service Support Tool)
0016-1423
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can back up the area of the HDD where MEAP applications reside to a PC, as when you want to format the HDD. MEAP devices use a license-based mechanismto control applications so that formatting the HDD will necessarily delete the jar files and application data, requiring you to not only reinstall them but also makenecessary settings. (Doing so consists in obtaining special license files for reinstallation and downloading user data/settings, increasing your work load.)
If you use the SST's backup function, you will be able to temporarily put aside the area of MEAP applications, thus being free of the foregoing extra work. Thisfunction, however, is limited to a specific MEAP device (serial number), and cannot be used for illegal copying of applications.
You must not perform any other work (including checking operation) until the HDD has been backed up. This arrangement is to prevent a mismatch of MEAPcounter readings and the HDD contents, and any fault in operation arising as the result of failure to observe this will not be covered by the guarantee of operation.
Memo:The application that is installed with a reusable license can be reinstalled by using the same license.
The following list shows the details of area that SST backs up;Jar files of MEAP applicationsSettings set with MEAP applications.Note that SST does not back up images in Mailboxes that MEAP applications use.User information data registered with SDL
Requirements for Backup Using the SSTThe following conditions must be met for use of the function:
1) Device Firmware VersionT-11-17
Boot ROM System SST
iR2220 SeriesiR2250 Series
24.42 later 33.01 later Since Ver 1.81
Chapter 11
11-37
2) SST VersionVersion 1.81 or later. An earlier version will not permit the use of the function. If needed, upgrade the SST.
3) Space for backupTo back up the HDD of the iR, the PC must have approx 300 MB of free space at maximum.
Making a Backup and Formatting Hard Disk Drive with Service Support Tool
1) If SDL or SSO is used for the login service, switch to default authentication before backing up the user information. Although SST will back up SDL user infor-mation, it is recommended to export the user information just in case. For SDL user information backup, go to User Management page of Simple Device Loginsite and export the data. (The SDL login page opens with the URL "http://<device IP address>:8000/sdl/").
If a hard disk of a system that uses SDL or SSO is formatted without changing the login service to the default authentication, the error message "The login servicemust be set again with SMS" appears and the system cannot start up when you attempt to restart the system after formatting. If this problem occurs, change thelogin service to SDL or SSO with SMS. If you cannot access to SMS since you do not have the IP address of the device, start the system with FIXIP mode -hold down the numeric keys 1 and 7 and turn the power switch on. The IP address "172.16.1.100" will be automatically assigned for the device. Then log in toSMS specifying the address.
2) While holding down the 2 and 8 buttons, start up the device in download mode.As in the case of Sramimg.bin, the function is available only when the device is in Download Mode.
3) Connect the PC to the device and start the Service Support Tool.
4) In Download/Upload session of SST, select the appropriate device model, System in the tree view, and take necessary steps to connect to the device.
5) Click Upload the Backup Data button.
6) Click the option "Meapback.bin" from Name list of Backup Data Available for Selection, and click Start Storing button.
Selecting Meapback.bin
F-11-57
7) When the data has been generated, enter an appropriate name in File name field and click Save button; then, click OK button to end the backup session.
8) In Selecting Model/Unit screen, select HDFormat and start formatting. All the partitions in the hard disk drive will be formatted.
Restoring the Backup Data1) After formatting the hard disk drive with SST, install the System, MEAP Contents, Language, and Remote UI files.
2) To restore the backup "Meapback.bin," click Download the Backup Data button.
iR5020 SeriesiR5160 Series
24.42 later 54.02 later Since Ver 1.81
Devices ither than those listed the above. Already supported since the 1st version. Already supported since the 1st version. The version supporting the corresponding devices.
Boot ROM System SST
Chapter 11
11-38
3) Select the backup data file and click Start Writing button to download the backup data. Note that SST cannot restore backup data created with a different version.
Selecting Backup Data
F-11-58
4) When the screen with OK button appears, the restoration of backup data finishes. Click OK button.
5) Reboot the main power and access the device with SMS and check that the MEAP applications are restored.
6) Restore non-MEAP backup data and settings that are saved before formatting the hard disk drive. The SDL user information is included in the backup data. Youdo not have to restore it.
11.1.23 Replacing the Hard Disk Drive0016-1424
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If you must replace the hard disk drive because of a fault, all MEAP application files stored on it will also be lost, requiring you to re-install the applications andtheir license files in addition to performing the normal work associated with the replacement of the hard disk.
Like other counter information, MEAP counter information will remain after replacement. Reinstallation of MEAP applications calls for special license files de-signed to continue with the current counter readings, thus enabling the use of the applications until the date of their expiration. These special licenses are servicetools, and are not offered to general users.
If you cannot make a backup of the license files as hard disk suffers a fault, contact the support staff of the regional headquarters of Canon telling the device serialnumber and the names of MEAP applications installed to the device to obtain the necessary special license files.
In the support departments of regional headquarters of Canon, all license files of the applications that have been issued are filed according to device serial numbers,enabling you to obtain a series of license files through a single screen as long as you can identify the serial number of the device in question.
The following shows the steps to follow after you have obtained a special license from the support staff of the regional headquarters of Canon.
1) Copy the set of special license files on the PC you are using for service work.Register the following with the Service Support Tool (SST): system file, language file, remote UI file, hard disk drive format file, MEAP contents file. (Be sureto pay attention to the version compatibility of individual files.)
2) Have the new hard disk drive at hand and replace it on site.While holding down the 2 and 8 keys at the same time, turn on the main power so that the machine will start up in download mode. The IP address 172.16.1.100will automatically be used, which enables you to download files in high speed through a network.)
3) Using the SST, format the new HDD, and install the System, MEAP Contents, Language, and Remote UI files.
4) When the device has started normally, obtain the jar files of the MEAP applications from the user, and install them using the license files of the applications inthe same way as you would when installing them for the first time.
5) As necessary, make login service selections and import user information.
Memo:If you format the hard disk without uninstalling MEAP applications, always reinstall the applications previously installed. Unless reinstalling them, lots for theMEAP counters the applications use will not be released. The message "The number of applications that can be installed has exceeded the limit. Try to installthis application after uninstalling other applications." may appear and the device does not accept to install new application. To install new applications, oncereinstall the applications installed before formatting and uninstall unnecessary applications.
11.1.24 MEAP Safe Mode0016-1425
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Use safe mode if you need to start up the system without worrying about extra applications. It will start up only those system software files (including SMS) thatnormally start up as default files while preventing MEAP applications and the like from starting up.
When you have made changes and turned off and then on the device, the control panel will indicate 'MPSF' in its lower right corner. The MEAP applications that
Chapter 11
11-39
may have been active before you shut down the equipment will not start up on their own. Make use of safe mode when restoring the system software as when MEAPapplications or services cause a fault as the result of a conflict or wrong sequence of registration/use. You can access to SMS in this condition so that you can takenecessary measures, for example, you can stop application that may cause the trouble.
If default authentication has been selected, the mode of authentication remains valid; otherwise, the message "The login service must be set again with SMS" ap-pears. Change the login service as necessary.
Starting in Safe Mode1) Start the device in service mode: click Ad Func key, press 2 and 8 buttons at the same time, and then click Ad Func key once again so that the service mode
screen appears.
2) Press COPIER button.
3) Press OPTION button.
4) Press USER.
5) Press the right-arrow button.
6) Press MEAPSAFE.
F-11-59
7) Press the 1 key on the control panel keypad to change the setting to '1'; then, click OK button.
F-11-60
8) Check that the notation 'MPSF' has appeared in the lower right corner of the screen; then, turn off and then on the main power.
F-11-61
If you want to end safe mode, repeat the steps but change '1' to '0' in step -7 and turn off and then on the main power.
Chapter 11
11-40
11.1.25 Setting HTTP port for MEAP application (level 2)0016-1426
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
For the ports in which the MEAP application uses, the default is 8000 for the port on HTTP server, and 8443 for the port on HTTPS server. In the case that theseports have already used by the customer who is to introduce this application, the MEAP application cannot use the HTTP (or HTTPS) server(s). By changing the following ports to use, however, the MEAP application can be used as well as the existing system.
HTTP serverSetting value is 0 through 65535 [the value at factory shipment/after clearing RAM: 8000]
HTTPS serverSetting value is 0 through 65535 [the value at factory shipment/after clearing RAM: 8443]
Memo:-As for port on HTTPS server, it only applies to the device that supports SSL function.-Make sure not to use 1 through 1023 other than 80 (HTTP) as a port for MEAP. Because the ports in this range are used by general servers, there is a possibilitythat the ports in this range will be duplicated in the future.
<Setting Procedure of Port on HTTP server>1) Startup [SERVICE MODE] (After pressing [USER MODE] button of MEAP device, press [2] button and [8] button at the same time on control panel. Thenby pressing [USER MODE] button again, [SERVICE MODE] screen is displayed).2) Startup level 2 of [SERVICE MODE] (After starting up [SERVICE MODE] in step 1, press [USER MODE] button again. Then, by pressing [2] button oncontrol panel, the screen is displayed.3) Press [COPIER] button.4) Press [Option] button.5) Press [BODY] button.6) Press [<-] button.7) Press [MEAP-PN] button.
F-11-62
8) Press the port number to specify on the control panel (the numerical value input in the field is displayed), and press [OK] button.
F-11-63
9) Check to see that it is reflected in setting field, and turn off the main power, and then, turn on the main power.
Chapter 11
11-41
F-11-64
<Setting Procedure of port on HTTPS server>1) Startup [SERVICE MODE] (After pressing [USER MODE] button of MEAP device, press [2] button and [8] button at the same time on control panel. Thenby pressing [USER MODE] button again, [SERVICE MODE] screen is displayed).2) Startup level 2 of [SERVICE MODE] (After starting up [SERVICE MODE] in step 1, press [USER MODE] button again. Then, by pressing [2] button oncontrol panel, the screen is displayed.3) Press [COPIER] button.4) Press [Option] button.5) Press [BODY] button.6) Press [<-] button.7) Press [MEAP-SSL] button.
F-11-65
8) Press the port number to specify on the control panel (the numerical value input in the field is displayed), and press [OK] button.
F-11-66
9) Check to see that it is reflected in setting field, and turn off the main power, and then, turn on the main power.
Chapter 11
11-42
F-11-67
Chapter 11
11-43
11.1.26 Reference material0016-1427
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
GlossaryT-11-18
Terms & Acronyms Definitions and ExplanationsApplet Applet Type Application. A Type of MEAP application that is designed to display user interface on device control panel.
Application A software unit that provides a solution to users.
Application ID A unique identifier assigned to each application. Used for indicating memory usage of the application in the MEAP system.
ASP Application Service Provider. A business to provide the application service on Internet.
AVS Applet Viewer Service. One of the MEAP system services that shows the user interface of the current applet type service on the console.
Code Sign To attach Digital Signature to software code. MEAP has the mechanism to reject MEAP application without Code Sign for security reason.
CPCA Common Peripheral Controlling Architecture. CPCA defines an object model of peripheral deices. A client can control a device by creating or modifying objects in the device.
CPCA Java CL CPCA Java Class Library. A Java class library, which is used to control a device.
Default Authentication - Department ID Management
The login service used when the department ID control is used but other authentication controls are not used. When the Department ID control is turned on, the login dialog prompts the users to enter the department ID and password. The dialog appears the initial screen of both the control panel on the MEAP device and Remote UI
Device Specification ID ID assigned for each device model. It shows the usage of functions that are equipped by MFP, as well as CPCA API specification and version numbers that is necessary for acquiring the values such as maximum number of copies, etc.
Chapter 11
11-44
DIS Dynamic Service Loading Installer Service. Receives data from the DSL on the MEAP platform. Enables an application to install to two or more devices.
DSL Dynamic Service Loading. While the SMS installs a license file and application to one device, the DSL can install them to two or more devices. It consists of MEAP ESM and the DIS.
Esplet Esplet Type Application. A type of MEAP application that does not have a user interface on the device console or on the web browser. The term of "Esplet" is a coinage by Canon inspired from Applet, Servlet, and "Espresso".
File descriptor With a file descriptor, an OS identifies the files that a program accesses. The file descriptor includes information such as file name and size as well as the identifier. An OS determines files to operate with the identifier.
iR Native Application The functionalities that existing imageRUNNER has such as Copy, Universal Send and Mailbox.
ISV Independent Software Vender. Software manufacturer who develops and/or sells applications and tools but does not entire computer systems. Refers application developer in this document.
J2ME Java 2 Platform Micro Edition. One of Java Platforms licensed by Sun Microsystems, Inc. It is applied for MEAP. Other devices such as cellular phones and PDA.
Java A programming language developed by Sun Microsystems, in the U. S. A. Low dependent on models and OSes and runs on various platforms. Taking advantage of this feature, many applications that runs on web servers uses Java. The MEAP platform uses J2ME - a type of Java.
Terms & Acronyms Definitions and Explanations
Chapter 11
11-45
Java Script A script language developed by Netscape Communications, in the U.S. A., runs on web browsers such as Netscape Navigator and Internet Explorer.Allows web designers to create interactive pages with HTML files such as animated buttons and display of timetables.
Java VM JAVA Virtual Machine. The Java byte code interpreter. The Virtual Machine acts as an interpreter for processing the byte code using the native instruction set.
License Access Number A number issued for accessing license file. The Licensing server requires entries of application ID, expiration date/times information, and the number of access numbers, to issue license access numbers.
License File A software manufacture of a MEAP application provides the users with the license files. Specifies the terms of agreement that a user concludes with the manufacturer. Required for installing a MEAP application.
Login Service Manages user information of MEAP device. Authenticates users with user names and passwords. Three login services are available for MEAP device - Default Authentication, which provides department ID control, SDL (Simple Device Login) and SSO (Single Sign-On).
MEAP Multifunctional Embedded Application Platform. Provides an environment for executing application programs on a peripheral device. Uses the Java platform (J2ME - Java 2 platform Micro Edition) to run Java application for MEAP.
MEAP AMS MEAP Application Management System. The license issuing server that issues "License File" necessary for MEAP applications to be installed onto MEAP device. Also used for issuing the "License Access Number".
MEAP Application Runs on MEAP platform. Consists of application files (*.jar) and the license file (*.lic).
Terms & Acronyms Definitions and Explanations
Chapter 11
11-46
MEAP Contents Required to install an MEAP application to a MEAP device.
MEAP ESM MEAP Enterprise Service Manager. One of software programs composing the DSL, to be installed on a PC in a Windows environment. Works as the interface with the DSL.
MEAP Specifications MEAP Spec Version, the term used for the SDK. The version number that shows the APIs of the MEAP platform other than CPCA, such as network and security. The version number is not assigned for each device model.
MEAP device imageRUNNER (iR) device that has MEAP Platform incorporated.
MFP Multi Function Peripheral. Peripheral device that supports more than one function, such as digital copier, printer, scanner, and fax.
OSGi Open Service Gateway Initiative. See "http://www.osgi.org/".
Portal Service The service displayed on a Web browser by inputting the address"http://<device IP address>:8000/" or "http://<device IP address>/"A portal to access a MEAP device from a Web browser.
Proxy Server Provides functions to store data fetched from remote servers. When a user request to display a web page that has been displayed and stored in the proxy, the proxy server read the stored data but does not access the remote server where the original page is present, for efficient access services. When a proxy server receives a URL from a PC, it searches the file in the cache and sends it to the PC if the requested file is found. If the requested file is not stored in the cache, it accesses the remote server of the URL to acquire the file and, at the same time, stores the acquired file in the cache so that the proxy server can quickly send the file at the next request.
Terms & Acronyms Definitions and Explanations
Chapter 11
11-47
Detail of License File
F-11-68
11.1.27 Option for exclusive individual measure0016-1428
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
-Display Setting of Copy TabMake a setting as to whether to display/hide the copy screen (copy tab) on the control panel. This is the specification for users who want to customize hiding it oncontrol panel.
Default value1: display
Setting range, item0: hide 1: display
Setting Procedure1) Startup [SERVICE MODE] (After pressing [USER MODE] button of MEAP device, press [2] button and [8] button at the same time on control panel. Thenby pressing [USER MODE] button again, [SERVICE MODE] screen is displayed).2) Press [COPIER] button.3) Press [Option] button.4) Press [BODY] button.5) Press [<-]or[->] (arrow) button.6) Press [UI-COPY] button.7) Press either 0 (hide) or 1 (display) on control panel (the numerical value input in the field is displayed), and press [OK] button.8) Check to see that it is reflected in setting field, and turn off the main power, and then, turn on the main power.
-Error at starting up the MEAP application/Setting to hide JAM screen (level 2)In the case that operation is restricted by MEAP application, hide the warning screen of error/JAM (such as JAM screen, door opening, no-toner). In the case thatthese errors occur, there will be a display indicating 'call the service personnel' etc.
Memo:Part of the warning screens is displayed if shifting to the device screen.- As for the screens for jam and no-toner, the warning screen (animation) can be displayed by pressing the followings: [Device Screen] > [Recovery Procedure]- As for the screen for door opening, the warning screen cannot be displayed because there is no display for [[Device Screen] > [Recovery Procedure]
Default value1: No activation of warning display
Setting range, item0: display warning screen 1: hide warning screen
����������������� �
������������� ��������������������������������
������������� ��������������������������������
�����!� "#$�����
��������%����� ���
&�'�()(*+ ���� ����, ����
&�'�()(*+ ���� ���, ����
&�'�()(*+ ���� ���, ����
&�'�()(*+ ���� ���, ���� &�'�()(%�������(��������� ����, ����
&�'�()(%�������(���������*+ ���, ����
&�'�()(%�������(���������*+���-� ���, ����
&�'�()(%�������(���������*+ (��� ���, ����
&�'�()( �������(��������� ����, ����
&�'�()( �������(���������*+ ����, ����
�'./$0��1��2�3*�&�)�"�'4��4�54�6�78�20$&�!'&�9�9:�)����99�3�(�+
;������� 8���<'/$#(=.$��*;)��>��?��6�-8 ���+�&4"�+��$�.�2�@$���
���"#:�
����� !�
����������� �2
������� ���� �2
A�)���� �����(�����
�������� %�����
Chapter 11
11-48
Setting Procedure 1) Startup [SERVICE MODE] (After pressing [USER MODE] button of MEAP device, press [2] button and [8] button at the same time on control panel. Thenby pressing [USER MODE] button again, [SERVICE MODE] screen is displayed).2) Startup level 2 of [SERVICE MODE] (After starting up [SERVICE MODE] in step 1, press [USER MODE] button again. Then, by pressing [2] button oncontrol panel, the screen is displayed.3) Press [COPIER] button.4) Press [Option] button.5) Press [BODY] button.6) Press [<-]or[->] button.7) Press [ANIM-SW] button.8) Press either 0 (display warning screen) or 1 (hide warning screen) on control panel (the numerical value input in the field is displayed), and press [OK] button.9) Check to see that it is reflected in setting field, and turn off the main power, and then, turn on the main power.
-Setting of Screen Transition from MEAP Screen to the Standard ScreenIn the case that the operation is restricted by MEAP application, make a setting to hide Native applications such as Copy/Send/Box. With this setting, disable screentransition with => key.
Default value0: OFF (transit to Native screen)
Setting range, item0: OFF (transit to Native screen) 1: ON (No-transition to Native screen)
Setting Procedure 1) Startup [SERVICE MODE] (After pressing [USER MODE] button of MEAP device, press [2] button and [8] button at the same time on control panel. Then,by pressing [USER MODE] button again, [SERVICE MODE] screen is displayed).2) Startup level 2 of [SERVICE MODE] (After starting up [SERVICE MODE] in step 1, press [USER MODE] button again. Then, by pressing [2] button oncontrol panel, the screen is displayed.3) Press [COPIER] button.4) Press [Option] button.5) Press [BODY] button.6) Press [<-] (arrow) button.7) Press [ANIM-DSP] button.8) Press either 0 (transit to Native screen) or 1 (no-transition to Native screen) on control panel (the numerical value input in the field is displayed), and press[OK] button.9) Check to see that it is reflected in setting field, and turn off the main power, and then, turn on the main power.
Chapter 12 RDS
Contents
Contents
12.1 RDS............................................................................................................................................................................12-112.1.1 Application operation mode..................................................................................................................................................... 12-112.1.2 Service Center URL and Port Specification ............................................................................................................................ 12-112.1.3 Communication test ................................................................................................................................................................. 12-112.1.4 Communication log.................................................................................................................................................................. 12-112.1.5 Detailed Communication log ................................................................................................................................................... 12-112.1.6 SOAP communication function ............................................................................................................................................... 12-112.1.7 Resend at SOAP transmission error......................................................................................................................................... 12-212.1.8 e-RDS setting screen................................................................................................................................................................ 12-212.1.9 Sleep operation......................................................................................................................................................................... 12-512.1.10 Network Setting (Maintenance) ............................................................................................................................................. 12-512.1.11 e-RDS Setting (Maintenance) ................................................................................................................................................ 12-512.1.12 Trouble shoot ......................................................................................................................................................................... 12-612.1.13 Error message......................................................................................................................................................................... 12-6
Chapter 12
12-1
12.1 RDS
12.1.1 Application operation mode0016-1357
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Serviceman selects the operation mode of OFF/ON by the setting in e-RDS setting screen of the service mode. (Menu Screen: E-RDS)- OFF (default): e-RDS doesn't operate.- ON: e-RDS operates every function.
12.1.2 Service Center URL and Port Specification0016-1358
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The URL and the port number of the equipment information destination can be specified as follows.- Default (specified beforehand)- Specified by the service mode. (Menu Screen: RGW-ADR, RGW-PORT)
12.1.3 Communication test0016-1359
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Serviceman can distinguish the communication status with the UGW by executing the communication test in the service mode (Menu Screen: COM-TEST), andreferring to the communication logError information is displayed in the latest communication log at communication error.
12.1.4 Communication log0016-1361
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The list of the log of the communication error (proxy server error etc.)(For 30) can be displayed in display panel in the service mode. (Menu Screen: COM-LOG)
12.1.5 Detailed Communication log0016-1362
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Detailed information of the error in the communication log can be displayed in display panel. (Log List Screen: Each error)
12.1.6 SOAP communication function0016-1363
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following processing is achieved by the SOAP communication (SSL client communication).e-RDS does the host authentication by using the CA*1 certificate of the VeriSign Co..When the host certificate or the CA certificate is expired, e-RDS doesn't connect to UGW.*1: CA: Certificate Authority: Organization that issues electronic certificate used by electronic commerce etc
(1) Communication test:- Do the communication test
(2) Regularly collect the following data, and transmit it.- Copy Counter- Service mode counter- Parts counter - Mode Counter- ROM version- Scheduling information- Application log
(3) When jam or alarm/service call error is detected from the device, e-RDS transmits to UGW.- Transmission of alert code(Counter information is transmitted at the same time. )When the state of the device changes, e-RDS sends the alert code list.The main alert codes used are Toner LOW/OUT, Jam, and Door open.When recovering from an error, e-RDS transmits data that shows the recovering from an error again.- Transmission of Jam log (Counter information is transmitted at the same time.)- Transmission of Alarm log (Counter information is transmitted at the same time.)- Transmission of Service Call (Error code) log (Counter information is transmitted at the same time.)
(4) Change of the device scheduling information- Scheduling information can be changed by the instruction from UGW.
Chapter 12
12-2
List of Transmissions:
12.1.7 Resend at SOAP transmission error0016-1364
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When SOAP send error is generated by the trouble on UGW side etc. at the transmission of an alert code, the latest three batches of data that failed in the transmissionare stored in HDD, and e-RDS resends it at prescribed intervals.
12.1.8 e-RDS setting screen0016-1365
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The e-RDS setting screen is in the service mode screen.When the tab above is selected on any e-RDS setting screen, it changes to the mid item screen. Moreover, it returns to previous screen when reset key is pressed.
Content of transmission Transmission timing
Communication test When Service mode of device is executed
Copy counter collection/transmission Every 6 hours
Service mode counter collection/transmission Every 6 hours
Mode counter collection/transmission Every 6 hours
Parts counter collection/transmission Every 6 hours
ROM version transmission Every 6 hours
Application log When the log file size exceeds 10kbytes
Transmission of alert code When the state of the device is changed.
Jam When Jam occurs
Alarm When Alarm occurs
Error When Error occurs
Confirmation whether there is processing that e-RDS executes
Every 6 hours
Chapter 12
12-3
Menu Screen
F-12-1Setting screen of e-RDS. The form and the initial value of each setting item are as follows.
Item(meaning) ExplanationE-RDS(Embedded-RDS)
Turning OFF/ON e-RDS. 0:OFF / 1:ONCounter information and error information are transmitted to the host at ON.Initial value: 0: OFF
RGW-ADR(RDS-Gateway ADDRESS)
URL of the host (When the input area is selected (touched), shift to the keyboard screen)Initial value: URL of an actual host.Length: 129 characters (NULL is contained)
RGW-PORT(RDS-Gateway PORT)
Port Number of the hostInitial value: 443Range of available number: 1-65535
COM-TEST(Communication Test)
Execution of Communication testCommunication test starts when you select (touch) this and press the [OK] key.e-RDS tries the connection with the host, and displays the result by "OK!" or "NG!". (NG: No Good, the communication test is failed)
COM-LOG(Communication Log)
The result of communication testWhen this is selected (touched), and the blank rectangle on right side is selected, it switches to "Log list screen".
Chapter 12
12-4
Log list screen
F-12-2History list of communication test error (error generation date, error code and error information) is displayed.When the each line is selected (touched), it shifts to "Log detailed screen".It shifts to "Menu screen" by the [Function] > [INSTALL].The list screen changes by a right arrow or a left arrow.Maximum log number: 30Notes: Only the first part of error information is displayed.
Chapter 12
12-5
Log detailed screen
F-12-3Detailed information of individual communication test error is displayed.Refer to the displayed message to "Error message list".It shifts to "Log list screen" by the [OK] button pressing.Maximum length of error information: 128 characters (not include NULL)
12.1.9 Sleep operation0016-1367
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When there is a method that should be transmitted while e-RDS is operating (ON), e-RDS wakes from the state of sleep and begins transmitting.
12.1.10 Network Setting (Maintenance)0016-1368
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You should do the network setting of Device appropriately before the e-RDS setting.A. Display the Additional Functions screen.
- Press [Additional Functions (*)] key.- Input ID code.
B. Display the TCP/IP Settings screen.- Select (touch) [System Settings] > [Network Settings] > [TCP/IP Settings] on the Touch Panel Display.
C. Setting of items related to IP address- Select (touch) [IP Address Settings] => IP Address Settings screen is displayed.- Set each items such as IP Address, Subnet Mask, Gateway Addresses, and DHCP, etc.- Return to the TCP/IP Settings screen by pushing the [OK] button after the setting ends.
D. DNS Settings- Select (touch) [DNS Settings] => DNS Settings screen is displayed.- Set necessary items.- Return to the TCP/IP Settings screen by pushing the [OK] button after the setting ends.
E. Proxy Settings- Select (touch) [Proxy Settings] (Press Down arrow button until [Proxy Settings] is displayed on the TCP/IP Settings screen.) => Proxy Settings screen isdisplayed.- Set necessary items.- Return to the TCP/IP Settings screen by pushing the [OK] button after the setting ends.
F. Display the normal screen.- Press [Additional Functions (*)] key pressing or press [Done] button to a necessary frequency.
12.1.11 e-RDS Setting (Maintenance)0016-1369
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
A. Display the Menu screen of e-RDS from the service mode.A-1. Shift to the service mode
Chapter 12
12-6
- Press [Additional Functions (*)] key.- Press 2 and 8 of the numeric keys at the same time.- Press [Additional Functions (*)] key. => SERVICE MODE LEVEL1
A-2. Initialize e-RDS- Select (touch) [COPIER] > [Function] > [CLEAR] > [ERDS-DAT] on the Touch Panel Display.
A-3. Display Menu screen of e-RDS - Select (touch) [COPIER] > [Function] > [INSTALL] => Menu screen
F-12-4B. Set 1 in [E-RDS].C. Input the URL of UGW in [RGW-ADR]. (Select the input area to shift to the keyboard screen, and Input URL.)D. Input the port number of UGW in [RGW-PORT]. E. Select [COM-TEST] and push [OK] button to start the communication test with UGW.F. While the result is "NG!", repeat to correct the setting and try [COM-TEST] until the result becomes "OK!". You need checking the setting of the network of the
device and the connection of the network if necessary.Notes: In the environment with the proxy server, you should set the proxy server. Refer to the proxy setting in the network guide of the device for details.
12.1.12 Trouble shoot0016-1370
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1-1Q. There is no setting item.A. Confirm the network setting.
Confirm the model
1-2Q. The communication test fails.A. Confirm the firmware version.
Confirm the network setting.Confirm the communication test result.
12.1.13 Error message0016-1371
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Error information displayed in "Log list screen" or "Log detailed screen" is as follows.
Notes: Only the first part of error information is displayed in "Log list screen". Maximum length of error information in "Log detailed screen": 128 characters (notinclude NULL)
When the communication test is not completed end e-RDS is 1 (ON), following string is displayed:"SUSPEND: Communication test is not performed."
Chapter 12
12-7
Moreover, when it fails in the event waiting in the device and either of a Jam notification, an Alarm notification, and a Service call notification or an Alert notifi-cation is specified, following string is displayed.
"Event Registration is Failed."
In other cases error information is displayed in the form of the following.
"[*] [Error string]: [Method name] [Server side detailed error]"
The enclosed character string by [] is replaced as follows.
[*]:
*(asterisk) is added to the head of the string only at the communication test.
[Error string]:As for number 1 and 2 of the following Error string lists, only the Error string is displayed. Besides, it is displayed as "[*] [Error string]: [Method name][Server side detailed error]". ([Server side detailed error] might not go out.)
Error string Cause Counter Measure1 SUSPEND: Communication
test is not performedThe e-RDS is started (the device is rebooted) when e-RDS is ON and communication test isn't done.
Complete the communication test.
2 Event Registration is Failed. The device failed event processing. Turn OFF/ON of the device main switch. Or, replace the system software of the device (upgrade).
3 URL Scheme error (not https) The header of registered URL of UGW is not https. Change the header on URL of UGW to https
4 Server connection error Communication failure of TCP/IP occurred.Or IP address of the device isn't set.
Check the network connection.
5 URL server specified is illegal Illegal URL (other than UGW) is specified. Correct URL.
6 Proxy connection error The e-RDS cannot connect it with the proxy server. Check and correct the proxy server address etc.
7 Proxy authentication error The e-RDS fails the authentication to proxy. Check and correct username and password to log in proxy.
8 Server certificate error - The certificate is not installed in The device.- The certificate that The user is using is not registered in The device or The server.
Register the root certificate in the device or register the VeriSign certificate in the server.
9 Server certificate expired - Expired certificate is registered in the device or the server.- The date of the device is outside the time limit of the certificate.
- Register the root certificate in expiration date in the device or register the VeriSign certificate in the server.- Set an accurate date to the device.
10 Unknown error Other communication error occurs. After waiting for a while, try again.
11 Server response error (NULL) UGW returns the error but communication to UGW is succeeded.If (NULL) is displayed after the message, the error occurs in the HTTPS communication.
After waiting for a while, try again.
12 Server response error (Hexadecimal)
UGW returns the error but communication to UGW is succeeded.(Hexadecimal) displayed after the message is error code that UGW returns.[server side detailed error] is added at the end of error information only at this error.
After waiting for a while, try again.
13 Device internal error Device internal error such as the memory cannot be taken occurs. Turn OFF/ON of the device main switch. Or, replace the system software of the device (upgrade).
14 Server schedule is invalid The schedule setting value given by UGW is found faulty at the time of communication test.
Report the detailed information of error occurrence to the support department.After the remedy by UGW, retry the communication test.
15 Server response time out There was no reply from UGW in predetermined time.(The congestion of the network etc.)It is the timeout at HTTPS level.
After waiting for a while, try again.
16 Service not found The URL of UGW is illegal, and UGW is inaccessible. Check and correct the URL of UGW.
Chapter 12
12-8
T-12-1
[Method name]:
[Server side detailed error]:Detailed error information returned from UGW is displayed for "Server response error".However, only the first 128 characters are displayed by the entire error information.Nothing is displayed here at other errors.
17 E-RDS switch is set OFF You execute the communication test while the E-RDS switch is OFF.
Turn ON E-RDS switch, and execute the communication test.
18 Server schedule is not exist The e-RDS receives empty schedule data from UGW. Check setting file. (Call the help desk of UGW.)
19 Network is not ready, try later You execute the communication when the connection to the network has not been established.(The network connection might not be established from the start-up of the device for 60 seconds.)
Confirm that the network connection has been established. Moreover, execute again after enough waiting.
20 URL error Illegal URL (Syntax error etc.) Correct URL.
Method name Meaning1 postServiceModeCount Account counter acquisition phase2 postModeCount Mode counter acquisition phase3 postPartsCount Parts counter acquisition phase4 postFirmwareInfo ROM version acquisition phase5 getOperationList Check/acquisition phase whether the information file for me is in UGW.6 postOperationOutcome7 postConfiguration Phase in which E-RDS configuration is transmitted to UGW
8 postGlobalClickCount Counter acquisition phase9 postJamLog Jam notification acquisition phase10 postServiceCallLog Error notification acquisition phase11 postAlert Alert notification acquisition phase12 postDebugLog Log acquisition phase13 getConfiguration Information acquisition phase (Schedule transmission etc.)
14 communicationTest Communication test phase
Error string Cause Counter Measure
Chapter 13 Maintenance and Inspection
Contents
Contents
13.1 Periodically Replaced Parts .......................................................................................................................................13-113.1.1 Outline...................................................................................................................................................................................... 13-113.1.2 Reader Unit .............................................................................................................................................................................. 13-113.1.3 Printer Unit............................................................................................................................................................................... 13-1
13.2 Durables and Consumables ........................................................................................................................................13-113.2.1 Outline...................................................................................................................................................................................... 13-113.2.2 Reader unit ............................................................................................................................................................................... 13-213.2.3 Printer Unit............................................................................................................................................................................... 13-2
13.3 Scheduled Servicing Basic Procedure........................................................................................................................13-213.3.1 Scheduled Servicing Basic Procedure ..................................................................................................................................... 13-213.3.2 Periodical Servicing Chart Reader Unit................................................................................................................................... 13-313.3.3 Periodical Servicing Chart Printer Unit ................................................................................................................................... 13-413.3.4 Points to Note for Periodical Servicing ................................................................................................................................... 13-5
13.4 Cleaning .....................................................................................................................................................................13-613.4.1 Cleaning Primary Toner Blocking Sheet ................................................................................................................................ 13-613.4.2 Cleaning Developing Toner Blocking Sheet .......................................................................................................................... 13-613.4.3 Cleaning Cleaner Scraper ....................................................................................................................................................... 13-613.4.4 Cleaning Photosensitive Drum ............................................................................................................................................... 13-713.4.5 Cleaning the fixing oil dish and the fixing cleaning belt guide ............................................................................................... 13-8
Chapter 13
13-1
13.1 Periodically Replaced Parts
13.1.1 Outline0015-5261
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Some parts of the machine must be replaced on a periodical basis for the machine to maintain a specific level of performance. They must be replaced regardless ofthe presence/absence of external changes or damage, as the performance of the machine will be considerably affected once they fail.If possible, plan any replacement to coincide with a scheduled visit.
The intervals indicated may vary depending on the site environment and user habit.
- Checking the Timing of ReplacementThe timing of replacement may be checked using the following service mode items:
COPIER > COUNTER > PRDC-1
13.1.2 Reader Unit0015-5262
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The reader unit does not have parts that require periodical replacement.
13.1.3 Printer Unit0015-5263
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-13-1
T-13-2
13.2 Durables and Consumables
13.2.1 Outline0015-5267
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Some parts of the machine may have to be replaced once or more over the period of machine warranty because of wear or damage. Replace them as needed byreferring to the table of estimated lives (expressed in terms of the number of prints they make).
Making Checks When Replacing DurablesUse the following service mode items to find out when to replace parts:
As of December 2006
No. Part name Part No. Q'ty Life Remarks
1 Primary, pre-transfer, transfer, separation charging wire
FB4-3687-000 AR 500,000 (*)
2 Primary grid wire FY1-0883-000 AR 500,000
3 thermistor unit FK2-5252-000 1 500,000 Main thermister + shutter thermister
4 Sub thermistor FM2-4161-000 1 500,000
5 Primary charging wire cleaner 1 FL2-4271-000 1 500,000
6 Primary charging wire cleaner 2 FL2-4272-000 2 500,000
7 Transfer charging wire cleaner 1 FL2-4271-000 1 500,000
8 Transfer charging wire cleaner 2 FL2-4272-000 1 500,000
9 Separation charging wire cleaner FF5-3090-000 2 500,000
10 Pre-transfer charging wire cleaner FF5-3090-000 1 500,000
11 Air filter 1 FC6-3482-000 1 500,000
12 Air filter 2 FC6-3483-000 1 500,000
13 Ozone filter FC6-3693-000 1 500,000
*: Do not use the old type (gold plated). After replacement of the charge wire, be sure to execute wire cleaning in service mode. (COPIER > FUNCTION > CLEANING > WIRECLN)
Chemical replaced parts As of December 2006
No. Part name Part No. Q'ty Life Remarks
1 Photosensitive Drum F43-7801-000 1 3,000,000
2 Collecting toner bottole F42-7901-000/F42-7911-000/F42-7921-000
1 44,000(TBD) 6% original :0.050g/A4 1Copy(TBD)
Chapter 13
13-2
- MachineCOPIER > COUNTER > DRBL-1- AccessoryCOPIER > COUNTER > DRBL-2
13.2.2 Reader unit0015-5268
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The reader unit does not have parts that are classified as "consumables" or "durables."
13.2.3 Printer Unit0015-7974
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-13-3
*1 As the fixing roller is used more and more, its surface tends to become discolored because of heat. The change, however, will not affect the performance of theroller. Also, note that the roller surface varies in color among manufacturers and the fact will not affect the roller performance.*2 As the pressure roller is used more and more, its rubber surface can start to discolor. The change, however, will not affect its performance or output images.Further, the physical properties of the roller can permit its surface to start to wrinkle. The roller, however, is free of wrinkles when it is heated and its performancewill not be affected, thus not requiring replacement.*3 Replace simultaneously with fixing roller. When you replace bushings, apply about 20 mg of grease (Molykote HP-300; CK-8012) on the inner and outer surfacesof the bushing until there is a white coating covering the entire sources.
13.3 Scheduled Servicing Basic Procedure
13.3.1 Scheduled Servicing Basic Procedure0015-5270
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
As of December 2006
No. Part name Part No. Q'ty Life Remarks1 Developing cylinder FM2-9641-000 1 1,000,0002 Developing assembly roll FB6-6569-000 2 1,000,0003 Cleaner separation claw FB2-6899-000 3 500,0004 Cleaning blade FA6-3995-000 1 1,000,000 Both edges are used; each for
500,000; apply toner upon replacement
5 Primary corona assembly FM2-3069-000 1 1,000,0006 Transfer/separation corona assembly FM2-9716-000 1 1,000,0007 Pre-transfer corona assembly FM2-9647-000 1 1,000,0008 Pre-separation charging assembly scraper FA4-1867-000 1 500,0009 Fixing roller FC4-4274-000 1 500,000 *1
10 Pressure roller FC7-4237-000FC7-4236-000(JPN only)
1 500,000 *2
11 Fixing web FY1-1157-000 1 500,00012 Pressure roller bearing XG9-0636-000 2 500,000
12 Insulating bushing (front/rear) FC6-3502-000 2 500,000 *313 Static eliminator (pressure roller) FC7-4287-000 1 500,000
14 Delivery upper separation claw FB5-3625-000 6 500,000
15 Delivery lower separation claw FA2-9037-000 2 1,000,00016 Pickup roller rear FF5-7830-000 4 500,000 Real use number of sheets (Each
holder uses 1 pc.)
17 Pickup roller front FF5-7829-000 4 500,000 Real use number of sheets (Each holder uses 1 pc.)
18 Pickup/feeding roller (deck, cassette) FB6-0615-000 4 500,000 Real use number of sheets (Each holder uses 2 pc.)
19 Separation roller (deck, cassette) FB5-6586-000 4 500,000 Real use number of sheets (Each holder uses 1 pc.)
20 Pickup/feeding roller (manual feed roller) FB1-8581-000 1 120,000 Real use number of sheets
21 Separation roller (manual feed roller) FB5-0873-000 1 120,000 Real use number of sheets
Chapter 13
13-3
- As a rule, provide scheduled servicing every 250,000 prints.- Check with the Service Book before setting out for a scheduled service visit, and take parts for which replacement is expected.- If the power plug is left connected for a long time in a place subject to dust, humidity, or oil smoke, a fire hazard is a possibility (i.e., the dust collecting aroundthe plug can absorb moisture, resulting in insulating failure). Be sure to disconnect the power plug on a periodical basis, and wipe off the dust and dirt collectingaround it.
<Work Procedure>1) Report to the person in charge, and check the general condition.2) Record the counter reading, and check the faulty prints.3) Make the following checks, and clean/adjust the items that are indicated:
T-13-4
4) Check the waste toner case. If half full or more, dispose of the waste toner in a vinyl bag or the like for collection; or, replace the waste toner case.
- If you need to dispose of the waste toner, be sure to do so in strict accordance with the regulations imposed by the local authorities.- Do not dispose of waste toner in a fire. Doing so may cause an explosion.
5) Clean the copyboard glass and the reading glass.6) Make test copies.7) Make sample copies.8) Check the operation of the leakage breaker.
With the power switch at ON, push the test switch of the leakage breaker to see that it operates normally (i.e., the breaker switch shifts to the OFF side to cutoff the power).If the leakage beaker fails to operate normally, replace it, and run a check once again.
<Resetting the Breaker>When you have made the check, turn off the main power switch, and turn on the breaker switch, and then turn the main power switch back on.9) Put the sample copies in order, and clean up the area around the machine.10) Record the final counter reading.11) Fill out the Service Book, and report to the person in change. Be sure to update the history of checks on the leakage breaker in the Service Book.
13.3.2 Periodical Servicing Chart Reader Unit0015-5271
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Do not use solvents or oils other than those indicated.
T-13-5
Items
Test copy against image density standard
for soiling of back of paper
for clarity of characters
for margin
for fixing misplaced registration, soiled back of paper
for margin standards (single-sided print) leading edge: 4.0+1.5/-1.0mm
left edge: 2.5+/- 1.5mm
(double-sided print) leading edge: 4.0+1.5/-1.0mm
left edge: 2.5+/- 2.0mm
Unit Location
Intevals
Remarksas needed
Chapter 13
13-4
13.3.3 Periodical Servicing Chart Printer Unit0015-5272
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Do not use solvents or oils other than those indicated.
T-13-6
Original exposure system
Copyboard glass clean
ADF reading glass clean
Scanner rail clean/lubricate Silicone oil (FY9-6011)
Scanner mirror (No.1 through No.3 mirrors)
clean
Reflecting plate clean
Unit name Part
Intervals
RemarksUponinstallation
every250,000
every500,000
every1,000,000
Externals/controls
Ozone filter ReplaceAir filter 1 ReplaceAir filter 2 ReplaceDust-proofingfilter (primary)
Clean Remove dust from surface.
Laser optical path Dust-proof glass CleanCharging assembly Charging wire
(primary, pretransfer, transfer/separation)
Clean Replace After replacement, execute wire cleaning 5 times.
Charging wire cleaner(primary, pretransfer, transfer/separation)
Replace Replace with charging wire simulta neously.
Grid wire(primary)
Clean Clean Replace
Charging assembly shielding plate (each charging assembly)
Clean Clean
Primary antistray toner sheet Clean
Roller electrode Clean CleanPhotosensitive drum
Photosensitivedrum
Clean Use alcohol and drumcleaning powder (CK-0429).
Electrode (for slip ring of drum heater)
Clean / Lubricate Clean with alcohol; 1) electrode,2) protrudingwall of electrode (where FY9-6008 is applied).- Charge collecting brush
Drum separation claw Clean Replace In a high temperature and high pressure environment, replaces it by 250,000
Developing assembly
Developing cylinder InspectDeveloping assembly roll Clean
Anti stray toner sheet CleanCleaner Side scraper Clean
collecting toner bottle holder Clean
Chapter 13
13-5
13.3.4 Points to Note for Periodical Servicing0015-5273
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Unless otherwise instructed, clean with lint-free paper and alcohol.
- Make a thorough check of the block (front, rear) for melting by leakage, deformation by heat, cracking, discoloration (yellowing). If a fault is found, replace thepart with a new one immediately.- Check the block (front, rear) including its inside.- Do not use a cloth on which metal powder is found.- If you have used solvent, make sure that the part has dried completely before mounting it back to the machine.- Do not use a moist cloth unless specifically indicated.- Be sure to provide scheduled servicing/replacement at the specified intervals.
F-13-1
Fixingassembly
Inlet guide CleanWeb InspectOil dish CleanWeb guide CleanThermistor unit Clean ReplaceSub thermistor Clean Replaceleft stay Clean Both sides driving shaft
Static eliminator (pressure roller)
Replace
Deliveryassembly
Separation claw (upper, lower)
Clean
Internal delivery roll CleanExternal delivery roll Clean
Toner collectionarea
Collecting toner box Inspect Inspect case, and remove toner.
Pickup/ feeding assembly
Transfer guide Clean
Registrationroller (upper, lower)
Clean
Feeding belt CleanFeeding rollers Clean
Unit name Part
Intervals
RemarksUponinstallation
every250,000
every500,000
every1,000,000
Pickup/feeding roller
Registration roller
Transfer guide
Vertical path roller
Pre-exposure glass
Reversing roller
Duplex Feeding Roller(right/left)
Dust-collecting roller Disposing of toner.
Separation claw, fixing assembly inlet guide Clean with solvent and lint-free paper.
Fixing oil pan, fixing cleaning belt guide Clean Dry wipe
Fixing roller(upper/lower) Use cleaning oil and lint-free paper.
Primary/Transfer/Separation/Pre-transfer charging assembly Dry wipe with lint-free paper; then, clean with alcohol.
Dust-proofing glassDry wipe with lint-free paper.
ADF reading glass
Copyboard glass
Scanning lamp Dry wipe with lint-free paper.Reflecting plate Clean with a blower brush.No. 1 through No. 3 mirrors Clean it with a blower brush; if dirt is excessive, dry wipe with lint-free paper.
Feeding assembly Clean with a moist cloth; see Note 1.
Developing assembly base Clean with a moist cloth; see Note 1.
Note 1: Do to leave traces of water.
Chapter 13
13-6
13.4 Cleaning
13.4.1 Cleaning Primary Toner Blocking Sheet 0016-0072
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the process unit. 2) Remove the potential sensor rail stay [2].
- 2 screws [1]
F-13-23) Clean the primary toner blocking sheet [1].
F-13-3
13.4.2 Cleaning Developing Toner Blocking Sheet 0016-0074
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the developing assembly, and clean the developing toner blocking sheet [1].
F-13-4
13.4.3 Cleaning Cleaner Scraper 0016-0077
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the cleaning blade. 2) Remove any paper lint accumulated at the tip of the cleaner scraper (A; the area between the magnet roller and the toner guide roller) with tweezers. 3) Remove the toner from the surface of the magnet roller. (Roll a paper into a U-shape to scoop it up.)
F-13-5
[1][2] [1]
[1]
[1]
4 8mm
A
Toner guide roller cleaner scraper (front)
Remove collected toner
(Front)
3040
mm
Chapter 13
13-7
F-13-64) Rotate the magnet roller in the clockwise direction (viewing from the front). 5) Repeat the step 3 through 4 until the area from which toner was removed in the step 3 is once again coated with an even layer of toner.
13.4.4 Cleaning Photosensitive Drum 0016-0080
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Do not rotate the magnet roller during work. Otherwise, waste toner may fall throught the cleaner assembly.
1) Remove the process unit.2) Remove the photosensitive drum.3) Moisten lint-free paper [1] with 5 to 10 cc of alcohol solutions [2]; then, pour 0.2 to 0.3 g of the drum cleaning powder (CK-0429) [3] on the lint-free paper. 4) While butting the lint-free paper relatively strongly against the photosensitive drum, wipe the surface of the drum from the front to the rear and from the rear to
the front.
F-13-7
- Keep the widths of cleaning to 5 to 10 cm in the peripheral direction of the drum. - Move the lint-free paper back and forth 15 to 20 times over a single area. Forcing the lint-free paper will not affect the life of the drum.
5) After the alcohol has evaporated, dry wipe the surface with the lint-free paper. If the area is uneven, go back to the step 4, and increase the back-and-forth move-ments.
6) Rotate the drum for the width (5 to 10 cm), and repeat the step 3 through 5 until the entire area of the surface has been cleaned.
A
Toner guide roller
4 8mm
cleaner scraper (rear)
Magnet roller
Remove collected toner
Rear
3040
mm
[1]
[2][3]
CK-0429
Chapter 13
13-8
F-13-8
13.4.5 Cleaning the fixing oil dish and the fixing cleaning belt guide0015-5278
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing web.2) Clean the surface of the silicone oil tray [1].3) Clean the surface of the fixing cleaning web guide [2].
F-13-9
5 10cm
[1]
[2]
Chapter 14 Standards and Adjustments
Contents
Contents
14.1 Image Adjustment Basic Procedure ...........................................................................................................................14-114.1.1 Making Pre-Checks.................................................................................................................................................................. 14-114.1.2 Making Checks on the Printer Unit (1/2)................................................................................................................................. 14-114.1.3 Making Checks on the Printer Unit (2/2)................................................................................................................................. 14-314.1.4 Making Checks on the Reader Unit ......................................................................................................................................... 14-414.1.5 Checking the Potential System ................................................................................................................................................ 14-714.1.6 Checking the Surface Potential Control System...................................................................................................................... 14-914.1.7 Potential Control System Conversion Table.......................................................................................................................... 14-1114.1.8 Emergency Measures for a Fault in the Potential Sensor ...................................................................................................... 14-16
14.2 Image Adjustments ..................................................................................................................................................14-1714.2.1 Standards of Image Position .................................................................................................................................................. 14-1714.2.2 Checking the Image Position ................................................................................................................................................. 14-1714.2.3 Adjusting Side Registration ................................................................................................................................................... 14-1714.2.4 Adjusting the Image Leading Edge Margin........................................................................................................................... 14-1814.2.5 Adjusting the Left/Right Non-Image Width .......................................................................................................................... 14-1814.2.6 Adjusting the Leading Edge Non-Image Width .................................................................................................................... 14-18
14.3 Scanning System ......................................................................................................................................................14-1914.3.1 After Replacing the Reader Controller PCB.......................................................................................................................... 14-1914.3.2 When Replacing the CCD Unit.............................................................................................................................................. 14-1914.3.3 Adjusting the Position of the No. 1/No. 2 Mirror Base ......................................................................................................... 14-1914.3.4 When Replacing the Copyboard Glass .................................................................................................................................. 14-2014.3.5 When Replacing the Reading Glass....................................................................................................................................... 14-2014.3.6 When Replacing the Scanning Lamp..................................................................................................................................... 14-2014.3.7 After Replacing the Inverter PCB.......................................................................................................................................... 14-20
14.4 Laser Exposure System............................................................................................................................................14-2014.4.1 When Replacing the Scanner Unit ......................................................................................................................................... 14-20
14.5 Image Formation System .........................................................................................................................................14-2014.5.1 Outline ................................................................................................................................................................................... 14-2014.5.2 Routing Charging Wire ......................................................................................................................................................... 14-2014.5.3 Routing Grid for Primary Charging Assembly ..................................................................................................................... 14-2114.5.4 Adjusting Height of Charging Wire ...................................................................................................................................... 14-2114.5.5 Mounting Cleaning Blade ..................................................................................................................................................... 14-2214.5.6 Removing Side Seal .............................................................................................................................................................. 14-22
14.6 Fixing System ..........................................................................................................................................................14-2214.6.1 Applying Grease After Replacing the Fixing Roller ............................................................................................................. 14-2214.6.2 Adjusting the Nip Width........................................................................................................................................................ 14-2314.6.3 Adjusting the Fixing Web Solenoid (SL9) ............................................................................................................................ 14-2314.6.4 After Replacing the Fixing Web ............................................................................................................................................ 14-2314.6.5 Adjusting the Fixing Inlet Guide Solenoid (SL1).................................................................................................................. 14-2314.6.6 Adjusting the Position of the Fixing Inlet Guide ................................................................................................................... 14-23
14.7 Electrical Components .............................................................................................................................................14-2314.7.1 When Replacing DC Controller PCB ................................................................................................................................... 14-2314.7.2 When Replacing HVT PCB .................................................................................................................................................. 14-2414.7.3 After Replacing the HDD ...................................................................................................................................................... 14-2414.7.4 When Replacing the Main Controller PCB ........................................................................................................................... 14-24
14.8 Pickup/Feeding System............................................................................................................................................14-2414.8.1 Points to Note When Mounting the Pickup Roller ................................................................................................................ 14-2414.8.2 Points to Note When Mounting the Separation Roller .......................................................................................................... 14-2414.8.3 The Points to Mount the Feeding Roller................................................................................................................................ 14-2414.8.4 Adjusting the Pressure of the Deck/Cassette Separation Roller ............................................................................................ 14-25
Contents
14.8.5 Adjusting the Pressure of the Manual Separation Roller....................................................................................................... 14-2514.8.6 Adjusting the Position of the Pickup Solenoid (SL3, SL4) of the Cassette 3/4..................................................................... 14-2514.8.7 Adjusting the Position of the Delivery Flapper Solenoid (SL5)............................................................................................ 14-2514.8.8 Adjusting the Position of the Right Deck Pickup Solenoid (SL6)......................................................................................... 14-2514.8.9 Adjusting the Position of the Left Deck Pickup Solenoid ..................................................................................................... 14-2614.8.10 Mounting the Reversing Flapper Solenoid .......................................................................................................................... 14-2614.8.11 Attaching the Side Guide Timing Belt in the Manual Feed Tray Assembly ....................................................................... 14-2614.8.12 Adjusting the Position of the Lifter Motor M20/M21 of the Cassette 3/4........................................................................... 14-26
Chapter 14
14-1
14.1 Image Adjustment Basic Procedure
14.1.1 Making Pre-Checks0015-5280
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Points to Note When Making a Check on the Printer Side
The machine's potential control mechanisms consist of those for copier image output and those for printer (PDL) image output, and permit independent adjustmentof service mode potential control parameters.If an image fault occurs, be sure to first find out which is at fault, prepare an image (data) accordingly, and then make appropriate adjustments.
F-14-1COPIER > TEST > PG > TYPECOPIER > OPTION > BODY PO-CNT
14.1.2 Making Checks on the Printer Unit (1/2)0015-5281
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Using the NA3 chart, make 2 copies each in the following modes:a. AE mode2. text mode3. text/photo mode
Generate several prints of the following test prints:1. PGTYPE: 4 (blank)2. PGYTPE: 5 (halftone)
Generate several prints each of printer (PDL) images that match the following:1. image with much white space -> for a check on fogging2. image including solid black -> for a check on solid black3. image including halftone -> for a check on halftone density
<Pre-Checks>
Clean the following:1. primary charging assembly grid wire2. primary charging wire3. pre-transfer charging wire4. transfer charging wire
If the fault is in the printer image,If the fault is in the copier image,
Output ConditionsF value = 5potential control: ON
Go to "Checking on the Printer Side."
Go to "Checking on the Reader Side.
YES
NOThe test print is free of a fault.
Check the following:[1] height of the charging wire
Chapter 14
14-2
F-14-2COPIER > FUNCTION > DPC > DPC
1. If there still is a difference in density after giving the adjusting screw 2 turns (each turn causing a change of about 0.7 mm), check the scanning lamp and thescanner for soiling.2. When making a clockwise turn, be sure that the intervals between wire grid runs are not larger than 9 mm.When making a counterclockwise turn, be sure that the intervals between wire grid runs are not smaller than 7.5 mm.
MEMO:Moving the wire from the photosensitive drum causes the image to be lighter, while moving it closer causes the images to be darker.
Is there a difference in density between
front and rear?
Is the rear lighter?
Turn the adjusting screw found at the front of the primary charging assembly clockwise. (2 full turns
Turn the adjusting screw found at the rear of the primary charging assembly clockwise. (2 full turns max.)
Generate one print of a halftone
<Checking the Density Slope>
YES
NO
YES
NO
Are there vertical lines in the image?
Are there vertical lines in the image?
<Checking Images> Checking Halftone Images
YES
YES
NO
NO
Execute forced potential control.
Generate a halftone image.
Clean the following; also check for foreign matter: 1. Dust-proofing glass2. Charging assemblies
A
Make the selections in service mode, and turn off and then on the main power switch: COPIER>FUNCTION>DPC>DPCSwitch off and on the main power switch.
Chapter 14
14-3
F-14-3COPIER > DISPLEY > DPOT > VDMCOPIER > DISPLEY > DPOT > VDM-PCOPIER > DISPLEY > DPOT > VL1MCOPIER > DISPLEY > DPOT > VL1M-PCOPIER > ADJUST > V-CONT > DE-OFSTCOPIER > ADJUST > V-CONT > DE-OFS-P
14.1.3 Making Checks on the Printer Unit (2/2)0015-5282
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Is it foggy?
Are the readings ± 6 V of the target value?
(*1)
<Checking fro Fogging>
YES
NO
NO
YES
NO
YES
Generate a blank print.
Check the following readings (VL1 target value) in service mode:COPIER>DISPLAY>DPOT>VL1M (for copier image)COPIER>DISPLAY>DPOT>VL1M-P (for printer image)
Check the following readings (VD target value) in service mode:COPIER>DISPLAY>DPOT>VDM (for copier image)COPIER>DISPLAY>DPOT>VDM-P (for printer image)
B
Check the following, and replace them if necessary: 1. Laser (for output)2. Potential control system
3. Photosensitive drum
Check the primary charging system and the potential control system; if normal, replace the photosensitive drum.
-50 -40 -30 -20 -10 0 +10 +20 +30 +40 +50
DefaultLighter image Darker image
Adjusting the Offset of the VL Target Potential (DE-OFFSET/DE-OFFSET-P) Vary the value using the following as a guide: COPIER>ADJUST>V-CONT>DE-OFST (for copier image) COPIER>ADJUST>V-CONT>DE-OFST-P (for printer image)
Are the readings ± 6 V of the target value?
(*2)
A
Chapter 14
14-4
F-14-4
F-14-5
14.1.4 Making Checks on the Reader Unit0015-5283
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
B
Is the density too low or too high (too
light or too dark)?
Are the readings ± 6 V of the
target value?(*1)
Adjust the offset of the VD target potential.
<Checking the Solid Black Density>
YES
NO
NO
YES
NO
YES
Generate a solid black print.
Check the following readings (VL1 target value) in service mode:COPIER>DISPLAY>DPOT>VL1M (for copier image)COPIER>DISPLAY>DPOT>VL1M-P (for printer image)
Check the following readings (VD target value) in service mode:COPIER>DISPLAY>DPOT>VDM (for copier image)COPIER>DISPLAY>DPOT>VDM-P (for printer image)
Check the following, and replace them if necessary:1. Laser (for output)2. Potential control system3. Photosensitive drum
Check the primary charging system; if normal, replace the photosensitive drum.
Are the readings ± 6 V of the
target value?(*2)
C
D
<Checking the Halftone Density>
Generate a halftone image.
End.
To check a copier image, See if No. 6 and No. 7 (halftone) of the Test Chart is reproduced to the more or less the same density.
To check a printer (PDL) image, See if the density of the halftone area represents the original data properly.
Is the halftone density optimum?
NO
YES
Adjusting the Offset Value of the VD Target Potential (VD-OFFSET/VD-OFFSET-P) COPIER>ADJUST>V-CONT>VD-OFST (for copier image) COPIER>ADJUST>V-CONT>VD-VD-OFST-P (for printer image)
DefaultLighter image Darker image
-5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5
C
D
Chapter 14
14-5
F-14-6
F-14-7
Is there a difference in density between
front and rear?
Are there vertical lines in the images?
Clean the following: 1. Mirrors 2. Lens 3. Standard white plate (mounted to back of copyboard glass)4. Copyboard glass
<Making Image Initial Checks> <Checking the Density Slope>
YESYES
NO
NO
NO
YES
Perform the instructions under “”for the printer unit.
Is there a difference in density
between front and rear?
Execute shading in service mode: COPIER>FUNCTION>CCD>CCD-ADJ
Execute shading in service mode: COPIER>FUNCTION>CCD>CCD-ADJ
Clean the mirrors.
E
Clean the following:1. Mirrors2. Lens3. Standard white plate4. Scanning lamp5. Reflecting plate
Make a copy of the NA3 Chart in text mode. Is gray scale No. 1 (solid black)
too light?
Check the life of the scanning lamp; if it has reached the end of its life, replace it.
<Checking the Solid Black Density> <Checking for Fogging>
YES
NO
NO
NO
Perform the instructions under “Checking the Solid Black Density”
for the printer unit.
YES
Is the density of gray scale No. 1 (solid black)
too low (light)?
Make a copy of the NA3 Chart in text mode.
Is the white background foggy?
YES
NO
Make a copy of the NA3 Chart in AE mode. Is the
output foggy?
K
Execute shading adjustment in service mode: COPIER>FUNCTION>CCD>CCD-ADJ.
Executing Potential Control
Turn off and then on the power switch; then, make a copy.
J
L
G
H
YESFE
Chapter 14
14-6
F-14-8
YES
YES
NO Is the white background
foggy?
Perform the instructions under “Checking for Fogging” on the printer side.
YES
NO
YES
Is the white background
foggy?
Decrease the value of AE density adjustment in service mode: COPIER>ADJUST>AE>AE-TBL.
Execute shading adjustment in service mode: COPIER>FUNCTION>CCD>CCD-ADJ.
Execute shading adjustment in service mode: COPIER>FUNCTION>CCD>CCD-ADJ.
Increase the white level target value for shading correction in service mode: COPIER>ADJUST>CCD>SH-TRGT (40 max.).
J
L
G
H
F
Chapter 14
14-7
F-14-9
14.1.5 Checking the Potential System0015-5284
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Checking Halftone Density>
End.YES
YES
NO
NO
Make one copy of the A3 Chart in
text/photo mode.
Go to “Checking the Solid Black Density” for the printer unit.
Is thedensity of gray scale
No.8 (halftone)different?
If it is too dark,
If it is too light,
When
the A3 Chart
is copied in text/photo
mode, is the density of No.8 optimum
when compared with Nos.7
through 9?
K
Decrease the setting of the
following in service mode:
COPIER > ADJUST > DENS
>DENS-ADJ
Increase the setting of the
following in service mode:
COPIER > ADJUST > DENS
>DENS-ADJ
Chapter 14
14-8
F-14-10
F-14-11
Turn off the main power
1. Disconnect the cable used to short the check pins on the DC controller PCB.
2. Connect the connector used between the DC controller PCBs of the potential control PCB.
turn off the main power
turn on the main power
Start
NO
YES
turn on the main power
NO
Is the image better?
YESYES
NO
YES
Is the difference between the measured PR-CNT and 'PRIMARY' shown in service
mode +/-10%?
NO
Try replacing the high-voltage transformer. Is
the problem corrected?
<Checking the Primary Output>
replace the DC controller PCB.
replace the DC controller PCB.
Is the value between 0 and 30?
End
A
Disable the potential control mechanism by entering '0' for the following:COPIER>OPTIONAL>BODY>PO-CNT.
1. short CP33 on the controller PCB and GND.2. disconnect the connector used between DC controller PCBs of the potential control PCB.
Make the following selections in service mode:COPIER>DISPLAY>DPOT>DPOT-K
Turn off the potential control mechanism by entering '0' for the following:COPIER>OPTION>BODY>PO-CNT.
Make the following selections in service mode (primary charging assembly current level): COPIER>DISPLAY>HV-STS>PRIMARY. Convert the value (in uA) indicated while printing is under way into a control voltage using the Potential Control Conversion Table.
Try replacing the photosensitive drum.If the problem is not corrected, go to 'Checking the Laser Output'.
Measure the voltage HVT_PRIMARY of J102A-11 on the DC controller PCB while copying is under way.
Check to make sure that the potential measurement PCB is supplied with power, and check the potential sensor using a checking electrode.
Forced execution of potential control
Enable potential control: COPIER>OPTION>BODY>PO-CNT=1.
Check the laser output.
Replace the laser unit.
NO
YES
YES
NO
Checking the Laser Output
B
Is the laser output a limit value?
Make the following selections in service mode, and enter '1': COPIER>FUNCTION>DPC>DPC.Switch off and on the main power switch.
Is the indication 70 ± 15 V?
Check the following indications:for copier images: COPIER>DISPLAY>DPOT>VL2Mfor printer images: COPIER>DISPLAY>DPOT>VL2M-P
A
Chapter 14
14-9
F-14-12
14.1.6 Checking the Surface Potential Control System0015-5286
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1. OutlineIf an image fault occurs, it is necessary to find out whether the cause is in the static image formation block including the photosensitive drum and the potentialcontrol system or if it is caused at time of development or transfer.An image fault may be isolated by finding out whether the surface potential is correct using service mode.
2. Disabling the Auto Control MechanismsAs a means of checking the potential control system, the auto control mechanism may be disabled (hereafter, non-auto control mode).If the image fault in question is more or less corrected when the machine is in non-auto control mode, you can suspect the potential measurement unit andthe DC controller PCB as the cause of the fault.You can also take advantage of non-auto control mode as a tentative remedy when the auto control mechanism has a fault.
When the machine is in non-auto control mode, all settings used for corona current control, laser power control, and developing bias control will be automaticallybe set to default settings.
Using Non-Auto Control Mode1) Make the following selections in service mode, enter '0', and press the OK key:
COPIER>OPTION>BODY>PO-CNT.2) Press the Reset key twice.
3. Making a Zero-Level checkA "zero-level check" is a check made to see if the control mechanism of the DC controller PCB is identifying a 0-V level without fail when the drum surfacepotential is 0 V.A zero-level check may be made in either of 2 ways, and you can use it to decided whether the DC controller PCB and the potential measurement PCB is freeof error:Method 1: use it to find out if the level shift circuit on the DC controller PCB is free of a faultMethod 2: use it to find out if the potential control circuit is free of a fault
(1) Method 11) Turn off the main power switch.
2) Remove the upper rear over.3) Short GP33 on the DC controller PCB and GND using a cable equipped with an alligator clips or probes on both ends.
When shorting CP33 and GND, take full care to avoid contact between the clip/probe and the pattern of the PCB and other elements.
4) Remove the left cover (upper), delivery cover, and left cover (middle).5) Remove the 5 screws [1], and detach the PCB cover [2].
Check the developing assembly for leakage; if normal, go to a check on the transfer output.
Make the following selections (DC value of the developing bias): COPIER>DISPLAY>HV-STS>BIAS. Covert the indication during printing (V) into a control voltage with reference to "Potential Control Conversion Table."
Is the deferense between
the actual measurement of HVT_DEV-BIAS_DC and 'BIAS'
in service mode ± 10%?
YES
NO
Checking the Developing Bias Output
1) Check the transfer charging assembly for leakage.
2) Make the following selections in service mode, and try changing the setting: COPIER>OPTION>BODY>FUZZY.
3) Try replacing paper.
Make the following selections in service mode (level of current of transfer charging). Convert the reading (mA) during printing into a control voltage based on 8.5 "Potential Control Conversion Table."
Replace the photosensitive drum.
NO
YES
NO
YES
NO
Is the difference between
the measurement of HVT_TRANSFER and 'TR' in
service mode +/- 10%?
Checking the Transfer Output
Is the toner image on the photosensitive
drum before transfer normal?
Replace the high-voltage transformer.
Is the problem corrected?
YES
Replace the DC controller PCB.
Replace the DC controller PCB.
END
Enable potential control: COPIER>OPTION>BODY>PO-CNT=1
B
Measure the voltage HVT_DEV_BIAS_DC during printing of J102A-8 on the DC controller PCB.
Disable the potential control mechanism by setting '0' for the following:COPIER>OPTION>BODY>PO-CNT.
Measure the voltage HVT_TRA during printing of J102A-12 on the DC controller PCB.
Chapter 14
14-10
F-14-136) Disconnect the connector [1] connected to the DC controller PCB of the potential control PCB.
F-14-147) Close the front door, and turn on the main power switch.
8) Make the following selections in service mode: COPIER>DISPLAY>DPOT>DPOT-K; then, check to see that the indication during initial rotation is between 0 and 30. If not, suspect a fault in the DCcontroller PCB.9) Turn off the main power switch.10) Remove the jumper wire found on the DC control PCB.11) Connect the connector of the potential control PCB.12) Mount the PCB cover, left cover (middle), delivery cover, and left cover (upper); then, close the front cover.13) Mount the upper rear cover.14) Turn on the main power switch.
(2) Method 21) Disable the potential control mechanism so that the machine is in non-auto control mode.
2) Turn off the main power switch.3) Remove the potential sensor from the machine.4) Connect the connector of the potential sensor to the connector of the machine.5) Fit the potential sensor checking electrode (FY9-3012) [2] to the potential sensor [1].
F-14-15
When fitting the checking electrode to the potential sensor, take full care so that the electrode will not come into contact with the potential sensor cover.
6) Connect the clip [1] of the checking electrode to the machine frame (GND).
[1]
[1] [1][1]
[2]
[1]
[2]
[1]
Chapter 14
14-11
F-14-16
Be sure never to bring the clip [1] into contact with the sensor cover. Also, be sure to fit it sufficiently away from the sensor window.
7) Fit the door switch actuator into the door switch assembly.8) Turn on the main power switch.
When you have turned on the main power switch, be sure never to touch the potential sensor.
9) Make the following selections in service mode: COPIER>DISPLAY>DPOT>DPOT-K. Then, check to see that the indication during initial rotation is between 0 and 30.
MEMO:1. If the result of Method 1 is as indicated but that of Method 2 is not, suspect soiling of the sensor and a fault in the potential measurement unit.
2. If the results of both Methods 1 and 2 are as indicated, assume that the signal path and operation from the potential sensor unit to the microprocessor on the DCcontroller PCB are normal.
10) Turn off the main power switch.11) Detach the potential sensor checking electrode.12) Mount the potential sensor.13) Turn on the main power switch.14) Enable the potential control mechanism.
14.1.7 Potential Control System Conversion Table0015-5287
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-14-1
Control (V) Primary (uA) Developing bias (V)
Pre-transfer (uA) Transfer (uA) Separation (uA)
3.00 1,400 0 0 440 100
3.05 1,391 3 -2 437 96
3.10 1,382 7 -4 434 92
3.15 1,373 11 -6 431 88
3.20 1,365 15 -8 429 85
3.25 1,356 18 -10 426 81
3.30 1,347 22 -12 426 77
3.35 1,338 26 -14 420 73
3.40 1,330 30 -16 418 70
3.45 1,321 33 -18 415 66
3.50 1,312 37 -20 412 62
3.55 1,303 41 -22 409 58
3.60 1,295 45 -24 407 55
[1]
Chapter 14
14-12
3.65 1,286 48 -26 404 51
3.70 1,277 52 -28 401 47
3.75 1,268 56 -30 398 43
3.80 1,260 60 -33 396 40
3.85 1,251 63 -35 393 36
3.90 1,242 67 -37 390 32
3.95 1,233 71 -39 387 28
4.00 1,225 75 -41 385 25
4.05 1,216 78 -43 382 21
4.10 1,207 82 -45 379 17
4.15 1,198 86 -47 376 13
4.20 1,190 90 -49 374 10
4.25 1,181 93 -51 371 6
4.30 1,172 97 -53 368 2
4.35 1,163 101 -55 365 -1
4.40 1,155 105 -57 363 -5
4.45 1,146 108 -59 360 -8
4.50 1,137 112 -61 357 -12
4.55 1,128 116 -63 354 -16
4.60 1,120 120 -66 352 -20
4.65 1,111 123 -68 349 -23
4.70 1,102 127 -70 346 -27
4.75 1,093 131 -72 343 -31
4.80 1,085 135 -74 341 -35
4.85 1,076 138 -76 338 -38
4.90 1,067 142 -78 335 -42
4.95 1,058 146 -80 332 -46
5.00 1,050 150 -82 330 -50
5.05 1,041 153 -84 327 -53
5.10 1,032 157 -86 324 -57
5.15 1,023 161 -88 321 -61
5.20 1,015 165 -90 319 -65
5.25 1,006 168 -92 316 -68
Control (V) Primary (uA) Developing bias (V)
Pre-transfer (uA) Transfer (uA) Separation (uA)
Chapter 14
14-13
5.30 997 172 -94 313 -72
5.35 938 176 -96 310 -76
5.40 980 180 -99 308 -80
5.45 971 183 -101 305 -83
5.50 962 187 -103 302 -87
5.55 953 191 -105 299 -91
5.60 945 195 -107 297 -95
5.65 936 198 -109 294 -98
5.70 927 202 -111 291 -102
5.75 918 206 -113 288 -106
5.80 910 210 -115 286 -110
5.85 901 213 -117 283 -113
5.90 892 217 -119 280 -117
5.95 883 221 -121 277 -121
6.00 875 225 -123 275 -125
6.05 866 228 -125 272 -128
6.10 857 232 -127 269 -132
6.15 848 236 -129 266 -136
6.20 840 240 -132 264 -140
6.25 831 243 -134 261 -143
6.30 822 247 -136 258 -147
6.35 813 251 -138 255 -151
6.40 805 255 -140 253 -155
6.45 796 258 -142 250 -158
6.50 787 262 -144 247 -162
6.55 778 266 -146 244 -166
6.60 770 270 -148 242 -170
6.65 761 273 -150 239 -173
6.70 752 277 -152 236 -177
6.75 743 281 -154 233 -181
6.80 735 285 -156 231 -185
6.85 726 288 -158 228 -188
6.90 717 292 -160 225 -192
Control (V) Primary (uA) Developing bias (V)
Pre-transfer (uA) Transfer (uA) Separation (uA)
Chapter 14
14-14
6.95 708 296 -162 222 -196
7.00 700 300 -165 220 -200
7.05 691 303 -167 217 -203
7.10 682 307 -169 214 -207
7.15 673 311 -171 211 -211
7.20 665 315 -173 209 -215
7.25 656 318 -175 204 -218
7.30 647 322 -177 203 -222
7.35 638 326 -179 200 -226
7.40 630 330 -181 198 -230
7.45 621 333 -183 195 -233
7.50 612 337 -185 192 -237
7.55 603 341 -187 189 -241
7.60 595 345 -189 187 -245
7.65 586 348 -191 184 -248
7.70 577 352 -193 181 -252
7.75 568 356 -195 178 -256
7.80 560 360 -198 176 -260
7.85 551 363 -200 173 -263
7.90 542 367 -202 170 -267
7.95 533 371 -204 167 -271
8.00 525 375 -206 165 -275
8.05 516 378 -208 162 -278
8.10 507 382 -210 159 -282
8.15 498 386 -212 156 -286
8.20 490 390 -214 154 -290
8.25 481 393 -216 151 -293
8.30 472 397 -218 148 -297
8.35 463 401 -220 145 -301
8.40 455 405 -222 143 -305
8.45 446 408 -224 140 -308
8.50 437 412 -226 137 -312
8.55 428 416 -228 134 -316
Control (V) Primary (uA) Developing bias (V)
Pre-transfer (uA) Transfer (uA) Separation (uA)
Chapter 14
14-15
8.60 420 420 -231 132 -320
8.65 411 423 -233 129 -323
8.70 402 427 -235 126 -327
8.75 393 431 -237 123 -331
8.80 385 435 -239 121 -335
8.85 376 438 -241 118 -338
8.90 367 442 -243 115 -342
8.95 358 446 -245 112 -346
9.00 350 450 -247 110 -350
9.05 341 453 -249 107 -353
9.10 332 457 -251 104 -357
9.15 323 461 -253 101 -361
9.20 315 465 -255 99 -365
9.25 306 468 -257 96 -368
9.30 297 472 -259 93 -372
9.35 288 476 -261 90 -376
9.40 280 480 -264 88 -380
9.45 271 483 -266 85 -383
9.50 262 487 -268 82 -387
9.55 253 491 -270 79 -391
9.60 245 495 -272 77 -395
9.65 236 498 -274 74 -398
9.70 227 502 -276 71 -402
9.75 218 506 -278 68 -406
9.80 210 510 -280 66 -410
9.85 201 513 -282 63 -413
9.90 192 517 -284 60 -417
9.95 183 521 -286 57 -421
10.00 175 525 -288 55 -425
10.05 166 528 -290 52 -428
10.10 157 532 -292 49 -432
10.15 148 536 -294 46 -436
10.20 140 540 -297 44 -440
Control (V) Primary (uA) Developing bias (V)
Pre-transfer (uA) Transfer (uA) Separation (uA)
Chapter 14
14-16
14.1.8 Emergency Measures for a Fault in the Potential Sensor0015-5288
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If the potential sensor goes out of order and, as a result, a transfer separation fault occurs, use the following service mode item to avoid problems; be sure, however,that this is merely a tentative remedy to be used until the potential sensor is replaced:1. COPIER>OPTION>TEMPO>F-POT-SW (Category 2)
Set '1' if a transfer separation fault occurs when the potential sensor has gone out of order.2. COPIER>OPTION>TEMPO>F-POT-D (Category 2) This is enabled when '1' is set for the foregoing service mode item.
0: if the user primarily uses originals with a low image ratio (text original). (default)1: if the user primarily uses originals with a high image ratio (photo originals)2: if re-transfer (drop-out about 50 mm of leading edge) occurs.
10.25 131 543 -299 41 -443
10.30 122 547 -301 38 -447
10.35 113 551 -303 35 -451
10.40 105 555 -305 33 -455
10.45 96 558 -307 30 -458
10.50 87 562 -309 27 -462
10.55 78 566 -311 24 -466
10.60 70 570 -313 22 -470
10.65 61 573 -315 19 -473
10.70 52 577 -317 16 -477
10.75 43 581 -319 13 -481
10.80 35 585 -321 11 -485
10.85 26 588 -323 8 -488
10.90 17 592 -325 5 -492
10.95 8 596 -327 2 -496
11.00 0 600 -330 0 -500
Control (V) Primary (uA) Developing bias (V)
Pre-transfer (uA) Transfer (uA) Separation (uA)
Chapter 14
14-17
14.2 Image Adjustments
14.2.1 Standards of Image Position0015-5289
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The image margin/non-image width of a print made in direct must be as fol-lows:mage Leading Edge Margin
F-14-17Left/Right Image Margin
F-14-18Leading Edge Non-Image Width
F-14-19Left/Right Non-Image Width
F-14-20
14.2.2 Checking the Image Position0015-5290
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Make prints using the following as the source of paper (10 prints each), andcheck to see that the image margin and the non-image width are as indicated:- Each cassette
- Front deck (left, right)- Manual feed tray- Duplex feeding unit- Side paper deck
If not as indicated, adjust the image position in the following order:1. Adjusting the left/right image margin (registration)
2. Adjusting the image leading edge margin (registration)3. Adjusting the left/right non-image width (CCD read start position)4. Leading edge non-image width (scanner image leading edge position)
14.2.3 Adjusting Side Registration0015-5291
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Cassette 3/4>1) Press the release button to draw out the cassette 3/4.2) Loosen the 2 fixing screws [1] on both sides of the cassette.3) Move the cassette body frontward or backward to adjust.
Backward: The side registration value (left margin) is decreased.Frontward: The side registration value (left margin) is increased.
F-14-214) Make sure that the side registration values (left margins) of a copy made
from the cassette 3/4 are L1 = 2.5±1.5mm respectively.
F-14-22[1] Paper feed direction
5) Tighten back the 2 fixing screws [1] after the adjustment.
F-14-236) Put back the cassette 3/4 to the machine.7) Perform the following service mode after the adjustment.
Cassette 3COPIER > FUNCTION > CST > C3-STMTR/A4RUse it to register the paper width basic value of the cassette 3.1) Put STMTR/A4R paper in the cassette3, and adjust the slide guideplate to the width.2) Select C3-STMTR/A4R to highlight, and press the OK key so that themachine executes auto adjustment and register the value.
Cassette 4COPIER > FUNCTION > CST > C4-STMTR/A4RThis operation is similar to cassette 3.
<Front Deck Left/Right>1) Press the release button to draw out the front deck left/right.2) Loosen the 2 screws [2] and 2 fixing screws [3] of the deck front cover [1].
1.5mm1.0mm
4.0
2.5 1.5mm
02
4
6
8
10
1.5mm1.0mm4.0
2.5 1.5mm
02
4
6
8
10
[1]
[2]
[1]
[2]
imageL1
[1]
[1]
Chapter 14
14-18
F-14-243) Move the cassette plate (front) [1] frontward or backward to adjust.
Backward: The side registration value (left margin) is decreased.Frontward: The side registration value (left margin) is increased.
F-14-254) Make sure that the side registration values (left and right margins) of a
copy made from the front deck left/right are L1 = 2.5±1.5mm respective-ly.
F-14-26[1] Paper feed direction
5) Tighten the 2 screws [2] and 2 fixing screws [3] of the deck front cover [1].
F-14-276) Put back the front deck left/right to the machine.
<Manual Feed Tray>1) Move the side plates [1] to the center. Loosen the 2 mounting screws [2]
of the manual feed tray, and adjust the position of the manual feed tray.
F-14-28
<Duplexing Feeder Unit>1) Select the following service mode COPIER > ADJUST > FEED-ADJ >
ADJ-REFE, and make an adjustment so that margin on the 2nd side imagewill be within specs.
F-14-29
14.2.4 Adjusting the Image Leading Edge Margin0015-5292
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Adjust the image margin in service mode so that it is as indicated: COPI-ER> ADJUST> FEED-ADJ> REGIST.
F-14-30
14.2.5 Adjusting the Left/Right Non-Image Width0015-5293
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Adjust the non-image width in service mode so that it is as indicated:COPIER> ADJUST> ADJ-XY> ADJ-Y.
F-14-31
14.2.6 Adjusting the Leading Edge Non-Image Width0015-5294
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Adjust the non-image width in service mode so that it is as indicated:COPIER> ADJUST> ADJ-XY> ADJ-X.
F-14-32
[1]
[2]
[2]
[3]
[3]
[1]
image
L1
[1]
[1]
[2]
[2]
[3]
[3]
[1]
2.5+/-2.0mm
Increase the value of ADJ-REFE (Margin is increased by 1mm with increase of 10)
Decrease the value of ADJ-REFE (Margin is decreased by 1mm with decrease of 10)
02
4
6
8
10
02
4
6
8
10
Decreasing the REGIST setting (A decrease by ‘10’ will increase the margin by 1 mm.)
Increasing the REGIST setting (An increase by ‘10’ will decrease the margin by 1 mm.)
2.5mm±2.0
Edge of image
Increasing the ADJ-Y setting (An increase by ‘10’ will increase the non-image width by 1 mm.)
Decreasing the ADJ-Y setting (A decrease by ‘10’ will decrease the margin by 1 mm.)
02
4
6
8
10
Image leading edge
Decreasing the ADJ-X setting(A decrease by '10' will decrease the width by 1 mm.)
Increasing the ADJ-X setting (An increase by '10' will increase the width by 1 mm.)
Chapter 14
14-19
14.3 Scanning System
14.3.1 After Replacing the Reader Controller PCB0015-9932
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure to generate the latest P-PRINT printout before replacing the readercontroller PCB.- If you are initializing the RAM on the reader controller without replacingthe PCBUsing the SST, upload the backup data of R-CON; initialize the RAM, andthen download the data, thus eliminating the need for the following.
1) Using the SST, download the latest system software (R-CON).2) Make the following selections in the service mode: COPIER > FUNC-
TION > CLEAR > R-CON. Then, press the OK key to execute RAM in-itialization. Thereafter, turn off and then back on the main power.
3) Enter the appropriate settings for the following items in the service mode:a. setting indicated on the service label (found behind the reader unit frontcover)
a-1. image read start position adjustment (X direction; in fixed readingmode)
COPIER>ADJUST>ADJ-XY>ADJ-Xa-2 image read start position adjustment (Y direction; in fixed readingmode)
COPIER>ADJUST>ADJ-XY>ADJ-Ya-3 shading position adjustment (in fixed reading mode)
COPIER>ADJUST>ADJ-XY>ADJ-Sa-4 feeder mode main scanning position adjustment
COPIER>ADJUST>ADJ-XY>ADJ-Y-DFa-5 ADF stream reading CCD reading position
COPIER>ADJUST>ADJ-XY>STRD-POSa-6 density manipulating value adjustment
COPIER>ADJUST>CCD>DFCH-G2COPIER>ADJUST>CCD>DFCH-G10(After inputs it, execute COPIER>FUNCTION>DF-LNR)
The machine retains ADF-related service data in the RAM of its reader con-troller.ADF adjustment is necessary whenever you have replaced the reader con-troller or initialized the RAM.
b. original stop position adjustment (X direction) (stream reading)FEEDER>ADJSUT>DOCST
c. original feed speed (magnification) adjustmentFEEDER>ADUST>LA-SPEED
4) Make adjustments using the following service mode items:a. ADF sensor sensitivity adjustment
FEEDER>FUNCTION>SENS-INTb. tray width adjustment
FEEDER>FUNCTION>TRY-A4 FEEDER>FUNCTION>TRY-A5RFEEDER>FUNCTION>TRY-LTRFEEDER>FUNCTION>TRY-LTRR
c. white plate data adjustmentCOPIER>FUNCTION>CCD>CCD-ADJ
d. ADF white level adjustmentCOPIER>FUNCTION>CCD>DF-WLVL1COPIER>FUNCTION>CCD>DF-WLVL2
Be sure to perform white plate data adjustment before performing ADFwhite level adjustment.
After having made the foregoing adjustments, put the P-PRINT printout inthe service book case, replacing the previous P-PRINT printout.
14.3.2 When Replacing the CCD Unit0015-9938
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Perform the following steps after replacing the CCD unit.
1) Enter the correction values to be described on the label included in theCCD unit (the 2 following items) in the service mode.- COPIER > ADJUST > CCD > DFCH2G2- COPIER > ADJUST > CCD > DFCH2G10
2) Transcribe the above correction values to the service label at the back ofthe front cover of the host machine.
3) Execute the following in the service mode.3-1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ)
3-2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-WLVL1/2)
Be sure to perform white plate data adjustment before performing ADFwhite level plate.
14.3.3 Adjusting the Position of the No. 1/No. 2 Mirror Base
0015-9941
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Arrange the mirror positioning tool (FY9-3009-040) so that it is ready foruse in the machine (by changing the pin position; REAR).
F-14-332) Arrange the mirror positioning tool so that it is ready for use in the ma-
chine (by changing the pin position; FRONT).
F-14-343) Fit the pins of the mirror positioning tool (front [2]; rear [3]) into the ap-
propriate holes [1] of the No. 1/No. 2 mirror base.
[A][B]
[C]
[B]
[A]
[A][B]
[C]
[B]
[A]
Chapter 14
14-20
F-14-35
F-14-364) Secure the end of the cable that has temporarily been fixed in place on the
hook of the reader unit frame.5) Fully tighten the screws on the cable fixing plate both at the front and the
rear.6) Detach the mirror positioning tool (FRONT, REAR).7) Put the detached parts back on by reversing the foregoing steps.
14.3.4 When Replacing the Copyboard Glass0015-9948
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Execute the following in the service mode:1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ)2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-
WLVL1/2)
Be sure to perform white plate data adjustment before performing ADFwhite level adjustment.
14.3.5 When Replacing the Reading Glass0015-5300
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Execute the following in service mode:
1) ADF white level adjustment (COPIER>FUNCTION>CCD>DF-WLVL1/2).
14.3.6 When Replacing the Scanning Lamp0015-9954
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Execute the following in the service mode:1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ)2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-
WLVL1/2)
Be sure to perform white plate data adjustment before performing ADFwhite level adjustment.
14.3.7 After Replacing the Inverter PCB0015-9957
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Execute the following in the service mode.1) White plate data adjustment (COPIER > FUNCTION > CCD > CCD-
ADJ).2) ADF white level adjustment (COPIER > FUNCTION > CCD > DF-
WLVL1/2).
Be sure to perform white plate data adjustment before performing ADFwhite level plate.
14.4 Laser Exposure System
14.4.1 When Replacing the Scanner Unit0015-9959
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If the temperature of the fixing assembly is 150 deg C or higher when themain power switch is tuerned on, the machine will not execute potential con-trol. If such is the case after replacing the scanner unit, manually execute po-tential control in service mode as follows:1) Make the following selections in service mode: COPIER> FUNCTION>
DPC> DPC; then, enter '1', and press [OK]. 2) Turn off and then back on the main power switch.
14.5 Image Formation System
14.5.1 Outline 0015-9961
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The photosensitive drum is surrounded by 3 charging wires; the primarycharging wire, the pre-transfer charging wire, and the transfer/separationcharging wire. These charging wires are newly adopted brown wires (0.06 mm in diameter).Do not use a gold-plated wire that has been used in the past; otherwise, imagefault may occur. Further, be sure to use a strengthened polishing pad (in a blue holder) as thecleaning pad for the primary charging assembly and the transfer charging as-sembly.
14.5.2 Routing Charging Wire 0015-9962
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
All charging wires (except the grid wire) are routed more or less in the sameway; the following cites the primary charging assembly. 1) Remove the shield plates (left, right) of the charging assembly. To prevent
deformation (deflection) in the primary charging assembly, be sure towork separately for the left shielding plate and the right shielding plate(do not loosen the screws [1] of both shielding plates at the same time.)
2) Remove the wire cleaner.
F-14-37
For other charging assemblies, remove the 2 covers.
[1]
[3]
[2]
[1]
Chapter 14
14-21
3) Free a length of about 5 cm of the charging wire (0.06 mm in diameter)from the charging wire reel, and form a loop at its end with a diameter ofabout 2 mm.
MEMO: To form a loop, wind the charging wire around a hex key once, and turn thehex key 3 to 4 times; then, twist the charging wire.
4) Cut the end (excess) of the twisted wire. 5) Hook the loop on the stud.
F-14-386) At the rear, hook the charging wire on the charging wire positioning plate;
then, hook the charging wire tension spring on the charging wire whereindicated to the following figure.
F-14-397) Cut off the excess of the charging wire with nippers. 8) Pick the end of the charging wire tension spring with tweezers, and hook
it on the charging power supply electrode. In the case of the pre-transfercharging assembly, hook the spring on the pin at the front.
F-14-40
F-14-41
Make sure the followings: - The charging wire must not be bent or twisted. - The charging wire must be fitted in the V-groove of the charging wirepositioning plate.
9) Attach a cushion in front of the charging wire (except the primary charg-ing assembly).
10) Attach the shield plates (left, right).
For other charging assemblies, attach the 2 covers.
11) Attach the wire cleaner. At this time, make sure the orientation of thewire cleaner.
12) Wipe the charging wire with lint-free paper moistened with alcohol so-lutions.
14.5.3 Routing Grid for Primary Charging Assembly 0015-9963
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Loosen the 2 screws used to secure the left and right shielding plates inplace.
2) Loosen the 3 screws used to secure the motor unit at the front in place.
F-14-423) Loosen the screw, and move it in the direction of the arrow indicated be-
low; then, temporarily tighten it in place. 4) Free a length of about 5 cm of the charging wire (0.1 mm in diameter)
from the charging wire reel, and form a loop at its end with a diameter ofabout 2 mm.
F-14-43
MEMO:To form a loop, wind the charging wire around a hex key once, and turn thehex key 3 to 4 times; then, twist the charging wire.
5) Cut the twisted charging wire (excess) with nippers. 6) Hook the loop on the stud A. 7) After routing the wire for 31 runs, lead it through the section B, and give
it a half turn; then, put it between the washer and the monitor unit, andwind it once around the screw (clockwise), and secure it in place with thescrew.
F-14-448) Cut the excess of the charging wire with nippers. 9) Tighten the screw loosened in the step 3.
Keep tightening until the tension of the grid wire is even. Be sure to payattention to avoid deformation (deflection) of the charging assembly (asby tightening the screw at the front of the left/right shielding plate early).
10) Tighten the screws loosened in the step 1 and 2. 11) Wipe the grid wire with lint-free paper moistened with alcohol solutions.
Make sure the followings: - The grid wire must not be bent or twisted. - The wires are laid at equal intervals. (The grid wire must be fitted in thegroove of the block.)
14.5.4 Adjusting Height of Charging Wire 0015-9964
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
[1] Primary charging wire
F-14-45Height of the charging wire
Charging electrode
(Rear) (Front) Charging wire
Reel Stud
(Correct) (Wrong)
Grid side
(Correct) (Wrong)
Screws
Screw
Stud A
Screw B
7.5 1.5 0 mm7.5 1.5
0 mm
Chapter 14
14-22
<Tolerance> +/-1 mm
[2] Pre-transfer charging wire
F-14-46Height of the charging wire <Tolerance> No height adjusting mechanism
[3] Transfer charging wire
F-14-47Height of the charging wire <Tolerance> +/-2 mm
[4] Separation charging wire
F-14-48Height of the charging wire <Tolerance> +/-2 mm
MEMO:The height (position) of the primary charging wire and the transfer chargingwire can be adjusted by turning the screw at the back of the charging assem-bly. A single turn changes the position of the charging wire by about 0.7 mm.
14.5.5 Mounting Cleaning Blade 0015-9970
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When mounting the cleaning blade, be sure that the side with the marking [1]will be the face. 1) Push in the cleaning blade [2] until it butts slightly against the rear.
F-14-492) Tighten the 5 screws [3] lightly, and stop to turn them when resistance is
felt. 3) Turn the screws tightened lightly in the step 2 about 20 to 30 degrees in
the order indicated below, and tighten them fully.
F-14-50
After mounting the cleaning blade, check that the edge of the blade is not ex-tremely bent. Further, be sure to clean the groove in the blade support plate before mount-ing the blade, as toner or the like in the groove can be the cause the bendingof the blade. ÅB
14.5.6 Removing Side Seal 0015-9972
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the old side seal. 2) Mount the new side seal [1] to the cleaner housing where indicated (both
ends). At this time, be sure that the edge of the side seal is positioned as follow: - When replacing the side seal [1] at the front, push the magnet roller [2]toward the rear, and then, make sure that the inner end of the side seal iswithin the area [3] of the washer. - When replacing the side seal [1] at the rear, push the magnet roller [2]toward the front, and then, make sure that the inner end of the side seal iswithin the area [3] of the washer.
3) The bottom end of each side seal [1] must be 0 to 0.5 mm from the cornerof the cleaner housing; i.e., point of reference [4].
4) Attach the side seal [1] at the front and the rear to the cleaner housingwhile making sure its position is as indicated.
F-14-51
14.6 Fixing System
14.6.1 Applying Grease After Replacing the Fixing Roller0015-9974
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- About 20mg of grease (Molykote HP-300; CK-8012) should be appliedto the inner [1] and the outer surfaces [2] of the bushing until the whitecoat covering is formed uniformly. If this undone, the noise (squeaking)may occur.
F-14-52- Applied grease may be transferred from the bushing to the fixing rollerends [1] when mounting; be sure to wipe it off when this happens.
10.06 0.3 mm
9.5 0.5mm
16.0
No gap Blade retaining plate
[2] [1]
Order of tightening
5
[3]
3 1 2 4
0 0.5mm
[3] [2]
[1] [4]
[1]
[2][1]
Chapter 14
14-23
F-14-53
14.6.2 Adjusting the Nip Width0015-9976
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The nip width adjustment is not necessary.
14.6.3 Adjusting the Fixing Web Solenoid (SL9)0015-9978
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
a. For New Fixing WebsAdjust the solenoid position with the screw [2] so that the drive lever [1]can shift up to 8.6mm.
F-14-54
b. For Used Fixing WebsBefore removing the solenoid, check the position (A) of the drive lever[1] when the solenoid is turned on. After replacing the solenoid, adjust thedrive lever [1] position with the screw [2] so that it positions as it didbefore replacement.
F-14-55
14.6.4 After Replacing the Fixing Web0015-9980
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
After replacing the fixing web, be sure to reset the counter reading to ‘0’ byusing the following service mode items.COPIER> COUNTER> MISC> FIX-WEBCOPIER> COUNTER> DRBL-1> FX-WEB
14.6.5 Adjusting the Fixing Inlet Guide Solenoid (SL1)0015-9982
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the position of the fixing inlet guide solenoid with the screw [1] sothat the guide positions as shown in the figure below when the solenoid isturned on.
F-14-56
14.6.6 Adjusting the Position of the Fixing Inlet Guide0015-5316
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the position of the solenoid using the two screws [1] so that the fixinginlet guide will be positioned as indicated when the solenoid turns on.
F-14-57<Points to Note When Making Adjustments in th Field>- The inlet guide is in low position when the solenoid (SL1) goes on.- The height of the inlet guide must be such that the difference between the
front and the rear must be 0.2 mm or less.- As necessary, adjust the height of the inlet guide by loosening the fixing
screw on the height adjusting support plate.
14.7 Electrical Components
14.7.1 When Replacing DC Controller PCB 0015-9986
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure to perform the followings when replacing the DC controller PCB. 1) Enter the latest values for the service mode indicated on the label [1] on
the back of the front cover with the service mode. 2) Enter the values indicated on the label [1] of the new PCB using the fol-
lowing service mode items: COPIER> ADJUST> HV-TR> D-PRE-TRCOPIER> ADJUST> HV-TR> D-HV-TRCOPIER> ADJUST> HV-SP> D-HV-SPCOPIER> ADJUST> DEVELOP> D-HV-DE
3) Move the J303 shorting connector [2] on the PCB from the existing to thenew PCB.
Make sure to connect the shorting connector. Otherwise, E004 occurs.
[1]
8.6mm
[1]
[2]
A
[1]
[2]
1.6m
m
Fixing roller
Pressure roller
Solenoid
Inlet guide
11.1
mm
12.7
mm
[1]
1.6m
m
Fixing roller
Pressure roller
Solenoid
Inlet guide
11.1
mm
12.7
mm
[1]
Chapter 14
14-24
F-14-58
14.7.2 When Replacing HVT PCB 0015-9990
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Enter the values indicated on the label of the HVT PCB using the followingservice mode items:
COPIER>ADJUST>HV-TR>H-PRE-TRCOPIER>ADJUST>HV-TR>HVT-TRCOPIER>ADJUST>HV-SP>HVT-SPCOPIER>ADJUST>DEVELOP>HVT-DE
14.7.3 After Replacing the HDD0016-0002
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
- Formatting the HDDStart up the machine in the safe mode (i.e., while holding down the 2 and 8keys, turn on the main power).Using the HD format function of the SST, format all partitions (BOOTDEV/PDLDEV/FSTDEV/FSTCDEV/TMP_GEN/TMP_FAX/TMP_PSS/IMG_MNG/APL_MEAP/APL_GEN/APL_SEND). (For details, see the de-scriptions given for upgrading.)- Downloading the system softwareUsing the SST, download the following: System, Language, RUI, MEAP-CONT (Meap content), SDICT (OCR dictionary), KEY (key/certificate forencrypted communication), TTS (audio dictionary).
14.7.4 When Replacing the Main Controller PCB0016-0011
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Upload each setting/registration data stored in SRAM of the main controllerPCB onto the PC by using SST. See the chapter ‘Version Upgrading’ for itsoperation procedure.If you are replacing the main controller PCB, be sure to transfer the follow-ing components from the old to new PCB.
F-14-59[1] Boot ROM[2] Hard disk[3] Image memory (SDRAM)[4] Counter memory PCB
14.8 Pickup/Feeding System
14.8.1 Points to Note When Mounting the Pickup Roller0016-0017
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Å°The direction of the mounting pickup rollerThe pickup roller may be mounted by reversing the steps used to remove it;however, be sure to keep the following in the mind.
- The roller used at the front and the rear of the machine is not compatible.- When mounting the pickup roller used at the front of the machine [1],make sure the round mark [2] and the punch mark [3] found on the sideof the roller are toward the front of the machine.
F-14-60- When mounting the pickup roller used at the rear of the machine [1],make sure the punch mark [2] is at the rear of the machine.
F-14-61
14.8.2 Points to Note When Mounting the Separation Roller
0016-0019
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When replacing the separation roller, be sure it is oriented as follows.
Mounting the separation roller in a wrong orientation may lead to interfer-ence against the crimping washer. Make sure it is mounted in a correct ori-entation.
Cassette 1/2, Right deck pickup assembly
F-14-62Left deck pickup assembly
F-14-63
14.8.3 The Points to Mount the Feeding Roller0016-0021
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When mounting the feeding roller [1] to the cassette pickup assembly, make
[1]
[2]
[1]
[2]
[3]
[4]
Direction ofrotation
Front side ofthe machine
[1]
[2]
[3]
Direction ofrotation
Rear side ofthe machine
[1]
[2][2]
Wider grooveNarrower groove
(front of machine)
(rear of machine)
Wider groove
Narrow groove
Chapter 14
14-25
sure the belt pulley [2] is at the front of the machine.
Check to make sure the protrusion in the roller plate and roller are engagedsecurely.
F-14-64
14.8.4 Adjusting the Pressure of the Deck/Cassette Separation Roller
0016-0023
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When picking up, if double feeding or pickup failure occurs, adjust the posi-tion of the pressure spring in the separation roller.
- If double feeding occurs, move the hook of the spring in the direction ofB.- If pickup failure occurs, move the hook of the spring in the direction ofA.
F-14-65[1] Feeding roller[2] Separation roller[3] Pressure lever[4] Pressure spring
14.8.5 Adjusting the Pressure of the Manual Separation Roller
0016-0025
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When picking up, if double feeding or failure occurs, adjust the position ofthe pressure spring of the separation roller.
1) Detach the right cover (upper).2) Remove the upper guide [1].
F-14-663) Move the mount [3] to adjust the position of the pressure spring of the sep-
aration roller.- If double feeding occurs, remove the mounting screw [2], lower themounting base [3] and tighten the screw [2] in the A hole. - If pickup failure occurs, remove the mounting screw [2], raise themounting base [3] and tighten the screw [2] in the B hole.
F-14-67
14.8.6 Adjusting the Position of the Pickup Solenoid (SL3, SL4) of the Cassette 3/4
0015-5326
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the position of the solenoid using the two screws [3] so that the dis-tance from the bottom of the pickup assembly to A of the roller arm is 36-/+0.5 mm when [1] and [2] are op-erated.
F-14-68
14.8.7 Adjusting the Position of the Delivery Flapper Solenoid (SL5)
0015-5327
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the position of the mounting screw [2] using the screw [2] so that thedrive lever [1] is pushed fully when the solenoid turns on (i.e., when theplunger is drawn).
F-14-69
14.8.8 Adjusting the Position of the Right Deck Pickup Solenoid (SL6)
0015-5328
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the position of the solenoid so that the left edge of the arm 2 is 57.2 -/+0.5 mm from the center of hole A of the solenoid mounting base.
[1]
[2]
rear
front
[1]
[2]
A
B
[3]
[4]
[1]
[1]
[2]
hole A
hole B
[1][2]
[1][2]
A
A
360.
5mm
[3]
[2][1]
Chapter 14
14-26
F-14-70
14.8.9 Adjusting the Position of the Left Deck Pickup Solenoid
0015-5329
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Before removing the left deck pickup solenoid from the support plate [1],take note of its position with reference to the fixing screw [2] of the solenoid.Or, mark the position for the solenoid by drawing a line on the support platewith a scriber.When mounting the solenoid on its own, be sure to secure it in its originalposition.
F-14-71
14.8.10 Mounting the Reversing Flapper Solenoid0016-0027
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Before removing the screw, make sure to mark the line in the following step.
1) Adjust the position of the solenoid using the 2 screws [1] so that the driverlever [2] is pushed fully when the solenoid is on (i.e., when the plunger isdown)
F-14-72
14.8.11 Attaching the Side Guide Timing Belt in the Manual Feed Tray Assembly
0015-5331
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Butt the rack plate [1] of the manual feed tray against section A (openstate).
2) Move the slide volume in the direction of B, and attach the timing belt [2]onto the pulley [3].
F-14-73
14.8.12 Adjusting the Position of the Lifter Motor M20/M21 of the Cassette 3/4
0016-0030
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the cable from the wire saddle, and detach the guide plate [3].- 1 connector [1]- 3 screws [2]
F-14-742) While keeping the lifter motor M21/M21 [1] to the right side, tighten the
screw [2] temporally.
F-14-753) Set the cassette 3/4 in the machine without paper.4) Check to make sure the lifer drive guar [1] is engaged with the lifter motor
guar [2] from the right side of the machine.5) Check to make sure the lifter drive guar is fully away from the lifter motor
guar when the release button of the cassette 3/4 [3] is pressed halfway.
The condition of “pressing released button halfway” is following.- Separation roller should move down.- The cassette roller is about to slide out.
F-14-766) If the lifter drive guar is not away from the lifter motor, move the position
of the lifter motor M20/M21 [1] to the left and check again with keepingthe release button of the cassette 3/4 pressed halfway.
[A]57.2 0.5mm
[2]
[1]
[1]
[2]
A
B
[3]
[2] [1]
[3][1]
[2]
[2]
[1]
[2]
[1]
[2][2]
Chapter 14
14-27
F-14-777) Fully tighten the 2 screws of the lifter motor M20/M21.8) Mount back the removed parts and turn the machine on.9) Check to make sure the cassette can be fully slid out when the cassette re-
lease button is pressed under the following conditions.- The cassette contains no paper- The cassette contains about 550 paper
[1]
Chapter 15 Correcting Faulty Images
Contents
Contents
15.1 Making lnitial Checks ................................................................................................................................................15-115.1.1 Site Environment ..................................................................................................................................................................... 15-115.1.2 Checking the Originals for Symptoms..................................................................................................................................... 15-115.1.3 Copyboard Cover, Copyboard Glass, and Standard White Plate............................................................................................. 15-115.1.4 Checking the Charging Assemblies ......................................................................................................................................... 15-115.1.5 Checking the Developing Assembly........................................................................................................................................ 15-115.1.6 Checking the Paper .................................................................................................................................................................. 15-115.1.7 Checking the Periodically Replaced Parts ............................................................................................................................... 15-115.1.8 Image Adjustment Basic Procedure......................................................................................................................................... 15-115.1.9 Others ....................................................................................................................................................................................... 15-1
15.2 Outline of Electrical Components..............................................................................................................................15-215.2.1 Clutch/Solenoid........................................................................................................................................................................ 15-2
15.2.1.1 Clutches and Solenoids ...............................................................................................................................................................................15-215.2.2 Motor........................................................................................................................................................................................ 15-3
15.2.2.1 Motors .........................................................................................................................................................................................................15-315.2.3 Fan............................................................................................................................................................................................ 15-6
15.2.3.1 Fans .............................................................................................................................................................................................................15-615.2.4 Sensor....................................................................................................................................................................................... 15-8
15.2.4.1 Sensors ........................................................................................................................................................................................................15-815.2.5 Switch .................................................................................................................................................................................... 15-13
15.2.5.1 Switches ....................................................................................................................................................................................................15-1315.2.6 Lamps, Heaters, and Others ................................................................................................................................................... 15-14
15.2.6.1 Lamps, Heaters, and Others ......................................................................................................................................................................15-1415.2.7 PCBs ...................................................................................................................................................................................... 15-16
15.2.7.1 PCBs .........................................................................................................................................................................................................15-1615.2.8 Connectors ............................................................................................................................................................................. 15-18
15.2.8.1 Connectors.................................................................................................................................................................................................15-1815.2.9 Variable Resistors (VR), Light-Emitting Diodes (LED), and Check Pins by PCB............................................................... 15-25
15.2.9.1 Variable Resistors (VR), Light-Emitting Diodes, and Check Pins by PCB .............................................................................................15-2515.2.9.2 DC Controller PCB ...................................................................................................................................................................................15-2515.2.9.3 DC Power Supply PCB .............................................................................................................................................................................15-2615.2.9.4 HVT PCB ..................................................................................................................................................................................................15-26
Chapter 15
15-1
15.1 Making lnitial Checks
15.1.1 Site Environment0015-5333
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The site must meet the following requirements:1) The main source of power must provide the rated voltage. (The power plug must remain connected throughout the night.)
2) The site must not be subject to high temperature/humidity (near a water faucet, water boiler, humidifier) or low temperature. It must not be near a source offire, and must not be subject to dust.3) The site must not be subject to ammonium gas.4) The site must be free of the direct rays of the sun; otherwise, curtains must be provided to block out the rays.5) The room must be well ventilated.6) The floor must keep the machine level.7) The source of power must provide power night and day.
15.1.2 Checking the Originals for Symptoms0015-5334
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Try to find out where the problem is caused by the originals or the machine:1) The copy density is optimum when it is as indicated by the index (5 -/+ 1).
2) An original with a reddish background prevents good contrast; e.g., red slips.3) Check the original for density:
MEMO:A diazo copy (used as an original) or an original with transparency tends to produce prints that are likely to be judged "foggy".An original prepared in pencil tends to produce prints that are likely to be judged "light".
15.1.3 Copyboard Cover, Copyboard Glass, and Standard White Plate0015-5335
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Check the copyboard cover, copyboard glass, and standard white plate for dirt and scratches. If soiled, clean it with mild detergent or alcohol; if scratched, replace it.
15.1.4 Checking the Charging Assemblies0015-5336
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Check each charging assembly for soiling and each charging wire for a fault (scratch, rust, etc.).2) Clean the charging wire of each charging assembly and the shielding plate; if the dirt is excessive, replace it.3) Check the type and the height of each charging assembly.4) Check to make sure that each charging assembly is correctly mounted.5) Check the charging wire cleaning pad (of each charging assembly) for displacement.
15.1.5 Checking the Developing Assembly0015-5337
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Check to make sure that the rolls on both ends of the developing assembly are in contact with the drum. Otherwise, "light images" may occur.
2) Check to make sure that the surface of the developing cylinder is coated with an even layer of toner. Otherwise, "light images" or "uneven density" may occur.
15.1.6 Checking the Paper0015-5338
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Check to see if the paper is of a recommended type.Advise the user that the use of paper not of a recommended type may not bring abut the best image quality.
2) Check to find out if the paper is moist.Try using paper fresh out of package.Advise the user that the use of moist paper will adversely affect transfer, generating poor images. Advise him/her on the correct method of storing paper.
15.1.7 Checking the Periodically Replaced Parts0015-5339
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Check with the Scheduled Servicing Chart and the Periodically Replaced Parts Table; if any part has reached the end of its life, replace it.
15.1.8 Image Adjustment Basic Procedure0015-5340
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
If the prints have uneven density (difference in density between front and rear), light images, or foggy background, perform the Image Adjustment Basic Procedure.
15.1.9 Others0015-5341
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Bringing in a machine from a cold to warm room in winter for installation can cause condensation inside the machine, leading to various problems.
MEMO:1) Condensation in the scanner (glass, mirror, lens) can cause dark images.
2) Condensation in the charging system can cause electrical leakage.3) Condensation on the pickup/feeding guide plate can cause paper feeding faults. If condensation is noted, dry wipe the parts, or leave the machine alone while powered for 60 min or so.
Chapter 15
15-2
15.2 Outline of Electrical Components
15.2.1 Clutch/Solenoid
15.2.1.1 Clutches and Solenoids0015-5383
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>The reader unit does not have clutches and solenoids.
<Printer Unit>T-15-1
T-15-2
Notation Name Description Remarks
CL1 developing cylinder clutch drives the developing cylinder
CL2 registration clutch drives the registration roller
CL3 manual feed pickup clutch drives the manual feed pickup roller
CL4 left deck pull-off clutch drives the left deck pull-off roller
SL1 fixing inlet guide drive solenoid drives the fixing inlet guide
SL2 manual feed pickup solenoid drives the manual feed pickup solenoid release
SL3 cassette 3 pickup solenoid drives the cassette 3 pickup
SL4 cassette 4 pickup solenoid drives the cassette 4 pickup
SL5 delivery flapper solenoid drives the delivery flapper
SL6 right deck pickup solenoid drives the right deck pickup
SL7 left deck pickup solenoid drives the left deck pickup
SL8 reversing flapper solenoid drives the reversing flapper
SL9 fixing web drive solenoid drives the fixing web
Notation Parts No. PART-CHK Duplexing drive PCB Motor driver PCB DC controller PCB
CL1 FK2-0852 CL>4 J108
CL2 FK2-0856 CL>5 J106
CL3 FK2-0851 CL>1 J108
CL4 FK2-0850 CL>2 J115
SL1 FK2-0841 SL>9 (recover)(SL10) (plunger drawn)
J106
SL2 FK2-0832 SL>5 J108
SL3 FH7-5702 SL>3 J110
SL4 FH7-5702 SL>4 J110
SL5 FK2-0835 SL>7 J106
SL6 FK2-0836 SL>1 J2105/ J2101 J104
SL7 FK2-0836 SL>2 J102
SL8 FK2-0838 SL>8 J2306/ J2302 J107
SL9 FK2-0839 SL>11 J106
Chapter 15
15-3
F-15-1
15.2.2 Motor
15.2.2.1 Motors0015-5385
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>T-15-3
T-15-4
Notation Name Description Parts No. E code
M501 scanner motor drives the No. 1/No. 2 mirror base FK2-3773 E202
Notation Connector
I/F PCB reader controller PCB
M501 J306/308 J202
SL3
SL4
SL5
SL2
SL8SL1
SL9
CL1
CL4
CL3CL2
SL7SL6
Chapter 15
15-4
F-15-2
<Printer Unit>T-15-5
Notation Name Description Remarks
M1 drum motor drives components associated with the photosensitive drum
M2 main motor drives major components of the printer unit
M3 fixing motor drives the fixing assembly
M4 right deck lifter motor drives the Lifter of the right deck
M5 Left deck lifter motor drives the lifter of the left deck
M6 primary charging wire cleaning motor drives the primary charging wire cleaner
M7 pre-transfer charging wire cleaning motor drives the pre-transfer charging wire cleaner
M8 transfer separation charging wire cleaning motor drives the transfer separation charging wire cleaner
M9 hopper stirring motor stirs toner inside the sub hopper, supplies toner to the developing assembly
M10 toner supply motor supplies toner from the toner bottle
M11 right deck pickup motor drives the right deck pickup
M12 cassette 3/4 pickup motor drives cassette 3/4 pickup
M13 delivery motor drives the delivery assembly
M14 reversal motor drives the reversing assembly
M15 shutter motor drives the fixing assembly shutter
M16 duplexing horizontal registration motor drives the horizontal registration mechanism of the duplexing assembly
M17 pre-registration motor drives the pre-registration roller
M18 duplexing feed right motor drives the right side of the duplexing feed assembly
M19 duplexing feed left motor drives the left side of the duplexing feed assembly
M20 cassette 3 lifter motor drives the lifter of the cassette 3
M21 cassette 4 lifter motor drives the lifter of the cassette 4
M22 laser scanner motor drives the polygon mirror
M24 left deck pickup motor drives the left deck pickup mechanism
M25 vertical path duplexing feed motor drives the curl-imparting roller, drives the duplexing outlet roller
M26 vertical upper motor drives the pickup vertical path 1/2 roller
M27 vertical lower motor drives the pickup vertical path 3/4 roller
M1
Chapter 15
15-5
T-15-6
T-15-7
Notation Parts No. PART-CHK Error
M1 FK2-3689 MTR>2 E012-0000
M2 FK2-3491 MTR>3 E010-0000
M3 FK2-3690 MTR>4 E014-0000M4 FK2-0017 MTR>25
M5 FK2-0017 MTR>26
M6 FH5-1138 MTR>17M7 FH6-1038 MTR>18M8 FH6-1038 MTR>19
M9 FK2-0813 MTR>20 (CW)MTR>21(CCW)
M10 FK2-0015 MTR>22
M11 FK2-3475 MTR>5
M12 FK2-3475 MTR>7
M13 FK2-0827 MTR>14
M14 FK2-4564 MTR>12
M15 FK2-0828 MTR>24
M16 FK2-0144 MTR>23M17 FK2-4563 MTR>15
M18 FK2-0826 MTR>13
M19 FK2-0826 MTR>16
M20 FK2-0814 MTR>27
M21 FK2-0814 MTR>28
M22 FM2-0018 MTR>1 E110-0001
M24 FK2-3475 MTR>6
M25 FK2-0824 MTR>8
M26 FK2-0820 MTR>10
M27 FK2-0822 MTR>9
Notation Duplexing drive PCB Motor driver PCB Video PCB DC controller PCB
M1 J108
M2 J108
M3 J106
M4 J2105/J2113 J105
M5 J2105/J2113 J105
M6 J103
M7 J103
M8 J106
M9 J103
M10 J103
M11 J2102/J2101 J104
M12 J2104/J2101 J104
M13 J106
M14 J2305/J2302 J107
M15 J128
Chapter 15
15-6
F-15-3
15.2.3 Fan
15.2.3.1 Fans0015-5387
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>
M16 J2306/J2302 J107
M17 J2102/J2101 J104
M18 J2307/J2302 J107
M19 J2305/J2302 J107
M20 J113
M21 J113
M22 J1406/ J116
M24 J2103/J2101 J104
M25 J2112/J2101 J104
M26 J2102/J2101 J104
M27 J2110/J2101 J104
Notation Duplexing drive PCB Motor driver PCB Video PCB DC controller PCB
M12
M1
M17
M25
M26
M24
M11
M27
M2
M20
M21
M6
M22
M7
M14M19
M18
M16
M4
M13
M5
M8
M9
M10
M15
M3
Chapter 15
15-7
T-15-8
F-15-4
<Printer Unit>T-15-9
T-15-10
Notation Name Description Parts No. ConnectorInterface PCB Reader controller PCB
FM501 reader unit cooling fan cools the reader unit FK2-0636 J313/J308 J202
Notation Name Description
FM1 feed fan discharges heat from the fixing unit
FM2 primary charging cooling fan cools the primary charging assembly and the cleaner
FM3 heat discharge fan discharges exhaust from fans to the outside of the machine
FM4 controller cooling fan cools the laser assembly, developing assembly, drive assembly, controller
FM5 curl-removing fan removes curl from print paper after fixing
FM6 DC power supply fan cools the power supply PCB
FM7 fixing heater power supply cooling fan cools the power supply for fixing
FM8 duplexing feed fan cools the duplexing feed motor
FM9 circulation duct fan cools the inside of the machine
FM10 accessories power supply cooling fan cools the accessories power supply FM11 HVT fan cools the HVT unit
Notation Parts No. I/O Error
FM1 FH5-1117 P013-0: half-speedP013-1: full-speed
1:ON E805-0002
FM2 FK2-0103 P013-2: half-speedP013-3: full-speed
1:ON1:OM
E824-0001
FM3 FH5-1118 P013-6: half-speedP013-7: full-speed
1:ON1:ON
E805-0001
FM4 FK2-0844 P014-2: half-speedP014-3: full-speed
1:ON1:ON
E121-0001
FM5 FH6-1548 P014-6: half-speedP014-7: full-speed
1:ON1:ON
-
FM6 P012-3 1:ON E804-0000
FM7 FK2-0795 P014-0P014-1
1:ON1:ON
E804-0001
FM8 FH6-1742 P014-5 1:ON -
FM9 FK2-0103 P023-2 1:ON -
FM10 FK2-0472 P015-1: half-speedP015-2: full-speed
1:ON E804-0002
FM11 FH6-1742 P013-4: half-speedP013-5: full-speed
1:ON -
FM501
Chapter 15
15-8
T-15-11
F-15-5
15.2.4 Sensor
15.2.4.1 Sensors0015-5388
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>
Notation DC power supply PCB Duplexing PCB DC controller PCB
FM1 J109
FM2 J103
FM3 J111
FM4 J108
FM5 J106
FM6 PN4001/J4002 J102
FM7 J124
FM8 J2303/J2302 J107
FM9 J124
FM10 J6503
FM11 J137
FM3
FM10
FM1
FM11
FM4
FM7
FM9
FM6
FM5
FM8
FM2
Chapter 15
15-9
T-15-12
F-15-6
<Printer Unit>T-15-13
Notation Name Description Parts No. Connector No.Interface PCB Reader controller PCB
SR1 ADF open/closed 1 sensor detects the state (open/closed) of the ADF
FK2-0149 J310/308 J202
SR2 Scanner HP sensor detects scanner home position FK2-0149 J310/308 J202
SR3 ADF open/closed 2 sensor detects the timing of original size FK2-0149 J310/308 J202
CF1-CF4 original size sensor detects the original size FK2-0238 J207(AB)J208(INCH)
Notation Name Description
PS2 Right lower cover open/closed sensor detects the Right lower cover open/closed
PS3 Manual feed tray open/closed sensor detects the manual feed tray open/closed
PS4 Claw jam sensor detects the claw jam
PS5 Right deck open/closed sensor detects the right deck open/closed
PS6 Right deck lifter sensor detects the right deck lifter
PS7 Right deck paper sensor detects paper in the right deck
PS8 Right deck limit sensor detects the right deck limit
PS9 Left deck open/closed sensor detects the left deck open/closed
PS10 Left deck lifter sensor detects the left deck lifer
PS11 Left deck paper sensor detects paper in the left deck
PS12 Left deck limit sensor detects the left deck limit
PS13 Cassette 3 paper sensor detects paper in the cassette 3
PS14 Cassette 4 paper sensor detects paper in the cassette 4
PS15 Cassette 3 open/closed sensor detects the cassette 3 open/closed
PS16 Cassette 4 open/closed sensor detects the cassette 4 open/closed
PS17 Cassette 3 lifter sensor detects the cassette 3 lifter
PS18 Cassette 4 lifter sensor detects the cassette 4 lifter
PS19 Right deck re-try sensor detects the right deck re-try
PS20 Left deck re-try sensor detects the left deck re-try
PS21 Cassette 3 re-try sensor detects the cassette 3 re-try
PS22 Cassette 4 re-try sensor detects the cassette 4 re-try
PS23 Manual feed paper sensor detects the Manual feed paper
PS24 Vertical path 1 paper sensor detects the vertical path 1 paper
PS25 Vertical path 2 paper sensor detects the vertical path 2 paper
PS26 Vertical path 3 paper sensor detects the vertical path 3 paper
PS27 Vertical path 4 paper sensor detects the vertical path 4 paper
PS28 Laser write start sensor detects the laser write start
PS29 Registration paper sensor detects the registration paper
PS30 Duplex pre- registration sensor detects the duplex pre- registration
PS31 Duplex horizontal registration sensor detects the duplex horizontal registration
PS32 Right deck feed paper sensor detects the right deck feed paper
SR2SR1
SR3
CF1 - CF4
Chapter 15
15-10
T-15-14
PS33 Left deck feed paper sensor detects the left deck feed paper
PS34 Duplexing paper sensor detects the duplexing paper
PS35 Internal delivery sensor detects the internal delivery
PS36 External delivery sensor detects the external delivery
PS37 Reversal sensor 1 detects the reversal 1
PS38 Reversal sensor 2 detects the reversal 2
PS45 Fixing web length sensor detects fixing web length
PS46 Delivery jam sensor detects the delivery jam
PS47 Right deck level sensor (upper) detects the right deck level (upper)
PS48 Right deck level sensor (lower) detects the right deck level (lower)
PS49 Left deck level sensor (upper) detects the left deck level (upper)
PS50 Left deck level sensor (lower) detects the left deck level (lower)
PS51 Fixing inlet sensor detects the fixing inlet
PS52 Fixing outlet sensor detects the fixing outlet
PS53 Shutter HP sensor detects the shutter HP
PS54 Toner access cover open/closed sensor detects the toner access cover open/closed
UN13 Manual feed tray paper width sensor PCB Detects the width of paper on the manual feed tray
UN14 Cassette 3 level sensor PCB Detects the level of paper in the cassette 3
UN15 Cassette 4 level sensor PCB Detects the level of paper in the cassette 4.
UN16 Cassette 3 paper width sensor PCB Detects the width of paper in the cassette 3.
UN17 Cassette 4 paper width sensor PCB Detects the width of paper in the cassette 4.
UN18 Cassette 3 paper length sensor PCB Detects the length of paper in the cassette 3.
UN19 Cassette 4 paper length sensor PCB Detects the length of paper in the cassette 4.
Notation Parts No. I/O DC controller PCB JAM
PS2 FK2-0149 P009-13 0:open J113
PS3 FK2-0149 P009-0 0:open J103
PS4 FK2-0149 P001-14 0:present J106 xx0F
PS5 FK2-0149 P009-11 0:open J112
PS6 FK2-0149 - - J112
PS7 FK2-0149 P001-7 1:present J112
PS8 FK2-0149 P002-4 1:present J112
PS9 FK2-0149 P009-12 0:open J115
PS10 FK2-0149 - - J115
PS11 FK2-0149 P001-9 1:present J115
PS12 FK2-0149 P008-4 1:present J115
PS13 FK2-0149 P001-3 1:present J110
PS14 FK2-0149 P001-5 1:present J110
PS15 FK2-0149 P009-8 0:open J110
PS16 FK2-0149 P009-9 0:open J110
PS17 FK2-0149 - - J110
PS18 FK2-0149 - - J110
PS19 FK2-0149 P001-2 1:present J112 xx0B
PS20 FK2-0149 P002-2 1:present J115 xx0C
PS21 FK2-0149 P002-0 1:present J110 xx0D
PS22 FK2-0149 P002-1 1:present J110 xx0E
PS23 FK2-0149 P001-0 0:present J108
PS24 FK2-0149 P001-8 1:present J113 xx03
PS25 FK2-0149 P001-10 1:present J113 xx04
PS26 FK2-0149 P001-4 1:present J110 xx05
PS27 FK2-0149 P001-6 1:present J110 xx06
PS28 FK2-0149 P002-8 1:present J113 xx02
PS29 FK2-0149 P001-1 1:present J106 xx01
PS30 FK2-0149 P002-5 1:present J107 xx16
Notation Name Description
Chapter 15
15-11
PS31 FK2-0149 P002-6 0:present J107
PS32 FK2-0149 P009-2 1:present J112 xx07
PS33 FK2-0149 P001-15 1:present J107 xx08
PS34 FK2-0149 P002-11 1:present J107 xx15
PS35 FK2-0149 P001-12 0:present J106 xx10
PS36 FK2-0149 P001-11 1:present J106 xx11
PS37 FK2-0149 P002-3 1:present J107 xx14
PS38 FK2-0149 P002-7 1:present J107 xx13
PS45 FK2-0149 P002-12 1:absent J128
PS46 FK2-0149 P008-09 1:present J106 xx12
PS47 FK2-0149 P006-8 1:present J115
PS48 FK2-0149 P006-12 1:present J115
PS49 FK2-0149 P006-9 1:present J115
PS50 FK2-0149 P006-13 1:present J115
PS51 FK2-0149 P008-8 1:present J106 xx18
PS52 FK2-0149 P002-13 1:present J106 xx17
PS53 FK2-0149 P002-14 0:HP J106
PS54 FK2-0149 P009-14 0:open J103
UN13 FG5-6231 - - J108
UN14 FG6-1941 P009-5 1:present J113
UN15 FG6-1941 P009-6 1:present J113
UN16 FG5-1957 - - J111
UN17 FG5-1957 - - J125
UN18 FG5-9581 - - J111
UN19 FG5-9581 - - J125
Notation Parts No. I/O DC controller PCB JAM
Chapter 15
15-12
F-15-7
UN14
UN18
UN19
UN16
UN17
PS50PS49
PS48PS47
UN15
PS25
PS23
PS26
PS13
PS15
PS27PS14
PS16PS18
PS22
PS21PS17
PS12PS20
PS10PS9
PS8PS19
PS6PS5
PS7
PS32
PS24
PS11
PS28
Chapter 15
15-13
F-15-8
15.2.5 Switch
15.2.5.1 Switches0015-5389
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>The reader unit does not have switches.
<Printer Unit>T-15-15
Notation Name Description Parts No.
SW1 main power switch turns on/off the main power FK2-0796
SW2 front cover switch detects the state (open/closed) of the front cover WC4-5125
SW3 environment switch turns on/off the drum heater WC1-5179
SW4 cassette heater switch turns on/off the cassette heater WC1-5179
SW5 waste toner feedscrew lock detection switch detects the state (locked) of the collecting toner feedscrew
WC4-0153
SW6 manual feed tray open/closed detection switch detects the state (open/closed) of the manual feed tray
WC4-5112
SW7 fixing feeding unit detection switch detects the presence/absence of the fixing feeding unit
WC4-5112
PS4
PS36
PS52
PS46PS35
PS45
PS51
PS53
PS29
PS54
PS37
PS38
PS34PS31
PS30
PS33
PS2
UN13
PS3
Chapter 15
15-14
F-15-9
15.2.6 Lamps, Heaters, and Others
15.2.6.1 Lamps, Heaters, and Others0015-5390
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>T-15-16
Notation Name Description Parts No.
H501 lens heater prevents condensation on the lens F26-4601 (100V; option)
FK2-0228 (230V; service part)
H502 mirror heater prevents condensation on the mirror F26-4601 (100V; option)
FK2-0229 (230V; service part)
LA1 scanning lamp illuminates originals FM2-3184 (100V/230V)FM2-3185 (120V)
SW4
SW3
SW1
SW5
SW6
SW7
SW2
Chapter 15
15-15
F-15-10
<Printer Unit>T-15-17
Notation Name Description Parts No.
LED1 pre-exposure lamp (LED) removes residual charges from the surface of the photosensitive drum
FK2-3694 (pre-exposure unit) iR5075/iR5075
FH7-3412 (pre-exposure unit) iR5065/iR5065N/iR5055/iR5065
IH fixing heater heats the fixing roller FK2-0807H1 drum heater prevents condensation on the photosensitive drum FK2-0786 (100V)
FK2-0787 (120V)FK2-0788 (230V)
H2 cassette heater prevents condensation in cassette (dries paper inside) FK2-0789 (100V)
FK2-0790 (230V; service part)
THM1 fixing main thermistor performs fixing temperature control, detects error FK2-5252 (thermistor unit)
THM2 fixing sub thermistor performs fixing temperature control, detects error FK2-0811
THM3 shutter thermistor performs fixing temperature control, detects error FK2-5252 (thermistor unit)
TP1 fixing thermal switch serves as a safety mechanism for the fixing assembly FK2-0808
ELCB leakage breaker prevents leakage of current FH7-7626 (100V)
FK2-0014 (120V)
FH7-7625 (230V)TS1 developing assembly toner sensor detects the level of toner remaining inside the
developing assemblyFK2-0812
TS2 sub hopper toner level sensor detects the level of toner remaining inside the hopper FK2-0812
THU1 temperature/humidity sensor measures the temperature/ humidity inside the machine
WP2-5200
C1 charger unit supplementary power supply device when printer and reader are made to work at the same time
FM2-9631iR5075/5075N only
H501
H502
LA1
Chapter 15
15-16
F-15-11
15.2.7 PCBs
15.2.7.1 PCBs 0015-5391
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>T-15-18
F-15-12
<Printer Unit>T-15-19
Ref. Name Description Parts No.[1] interface PCB serves as the interface with the printer and ADF FM3-0471[2] Memory PCB FM3-0472
[3] reader controller PCB controls the reader unit FM3-0470[4] CCD/AP PCB performs analog image processing FM2-4818 (CCD unit)
[5] inverter PCB drives the scanning lamp FK2-0630
Ref. Name Description Parts No.[1] DC controller PCB controls the power supply to the printer unit/finisher FM2-9857
[2] DC power supply PCB supplies DC power FK2-3472Åi100V/120VÅj
FK2-3473Åi230VÅj
[3] AC driver PCB controls the AC circuitry FM2-9861 (100V; AC driver unit)
FM2-9861 (120V; AC driver unit)
FM2-9862 (230V; AC driver unit)
[4] motor driver PCB controls the motor FM2-9895
TS2
THU1
TS1
LED1
H1 / TH5
H2
C1
ELCB
THM3
THM1
TP1
THM2
IH
[3] [4]
[5]
[1]
[2]
Chapter 15
15-17
[5] HVT1 PCB generates high voltage FM2-9897iR5065/iR5065N/iR5055/iR5055NFM2-9859iR5075/iR5075N
[6] potential PCB controls the surface potential of the photosensitive drum FM2-0839
[7] drum heater control PCB controls the drum heater FM2-0841 (100V/120V)
FM2-0842 (230V)
[8] option power supply PCB supplies power to the finisher FK2-2660Åi100VÅj
FK2-2661Åi230VÅj
FK2-3476(100/230 universal)
[9] duplexing drive PCB controls the sensors, motors, and solenoids of the duplexing unit
FM2-9903
[10] laser drive PCB controls the laser drive FM2-9860 (laser scanner unit)
[11] BD developing PCB detects the laser beam FM2-0859 (laser scanner unit)
[12] control panel keypad PCB controls the keys and LEDs FM2-1250
[13] control panel CPU PCB controls the control panel FM2-1249
[14] control panel inverter PCB adjusts the contrast of the control panel FM2-1251
[15] rush-current prevention PCB prevents rush current to the fixing feeding/duplexing unit FG6-4978
[16] capacitor PCB removes noise FM2-9864 (100V/120V; AC driver unit)
FM2-9896 (230V; AC driver unit)
[17] fixing heater power supply PCB controls the fixing heater FM2-3647 (100V)
FM2-3648 (120V)
FM2-3649 (230V)
[18] main controller PCB performs digital image processing/system control FM3-0221
[19] PCI expansion PCB serves as a relay PCB FM2-5429 (option)
[20] drum cleaner thermistor PCB detects clogging of the cleaner FM2-3661
[21] potential sensor PCB measures the photosensitive drum surface potential FM2-3657
[22] reader relay PCB generates high voltage FM3-0233
[23] Video PCB image control FM2-9868[24] Separation claw AC PCB generating the separation claw bias FM3-0957[25] Filter PCB removing the noise FM2-9865 (100V)
FM2-9866 (120V/230V)
[26] 13V converter PCB generates 13V FM2-9869
Ref. Name Description Parts No.
Chapter 15
15-18
F-15-13
15.2.8 Connectors
15.2.8.1 Connectors0015-5393
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Reader Unit>
[4]
[8]
[5]
[1]
[18]
[19]
[15]
[10]
[2]
[13]
[24]
[17]
[14]
[12]
[11]
[9]
[16]
[3]
[21]
[7]
[20]
[25]
[22]
[23] [6]
[26]
Chapter 15
15-19
F-15-14
<Printer Unit>
J2
J202
J102
J101
J505
J203
J315
J306J305
J308J503
J502
J505
J6
J7
J8
J5100J309
J5101
J601
J206
J205
J602
J207
J204
J301J313
J310
J312
J501
J5102J203
Chapter 15
15-20
F-15-15
J516
J517J513
J511
J518J515
J512
J564
J561
J568
J567J717
J110
J112
J115
J565
J569
J116J4500
J5503J2204
J5501
J115
J419
J804
J9004
J9003
J9006J802
J810
J806
J9008
J805J809J8508
J8492
J1521
J571
J572
J5701
J421J5700
J534
J5370
J537
J532J535
J536J533
J544
J5470
J547
J542J545
J546J543
J541
J531
J126J122
J2511
J2701
J1402
J1015
J6502
J1409J1403J1401
J1408
J4002
J4008
J1406J1411
J1519J1523
J803
J807
J113
J2106J2105
J801
J573
J418
J574
CP1000
Chapter 15
15-21
F-15-16
J4070
J154
J157
J153
J323
J407
J4260 J426
J160
J1404
J2053
J1502J2
J408
J103J1504
J2002J3
J4
J15
J427
J203J3230
J1405
J191
J192J193
J162
J161
J1610
J163
J151
J165
J1761
J203
J103
J227
J229 J236
J224
J225
J234
J222
J1513
J231
J223
J228
J235J230
J1518J233
J2305J2302
J2306J2301
J2303
J2307
J226
J232
J222
J712
J107
J156J155
J150
J158
J153
Chapter 15
15-22
F-15-17
J273
J259
J270J274
J258
J268
J263
J611J612
J260J254
J255
J261
J262
J271
J251
J251
J251
J128
J118
J106
J119
J3005
J3005
J256
J3004 J304
J303
J3301J257
J3009
J1004
J1003
J1006
J1005
J3003
J3002
J3008
J3007
J3006
J264
J727 J728
J729
J726
J1
J1403
J205
J125
J4013
J3502
J8403
J3504
J5
J3503 J6
J9014
J9013
J1251
J8400
J6503
J1291
J8402
J1241
J129
J129
J8401
J6403
Chapter 15
15-23
F-15-18
J1114
J6801
J1112
J6801J6802
J1533J1018J1060
J1024J1062
J9011J1354
J1355
J3J2
J1
J4001
J4016
J350
J2054
J754J114J123
J124
J1541
J1542
J11
J753
J9
J1113
J1111
J1110
J511
J9000
J1023
J9001
J3000
J2051
J7J8
PN4001
J1 J1022
J503
Chapter 15
15-24
F-15-19
J4013J4002
J4502
J9741
J102
J119
J705
J704
J2055
J707J701
J1021
J703
J3001
J3002
J4017
J104
J414
J412
J2122
J2102
J2104J418
J2113
J2103
J2110
J413
J4111
J411
J417J4171
J105
J2101
J2052
J2601
J2004
J2602
J107
J3100
J109
J101
J5
J9007
J8
J211J10
J2441
J4505J566
J742
J4503
J4015
J4007
J111
Chapter 15
15-25
F-15-20
15.2.9 Variable Resistors (VR), Light-Emitting Diodes (LED), and Check Pins by PCB
15.2.9.1 Variable Resistors (VR), Light-Emitting Diodes, and Check Pins by PCB0015-5395
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Of the variable resistors (VR), light-emitting diodes (LED), and check pins found in the machine, those that are needed when servicing the machine in the field arediscussed.
- Some LEDs carry current and emit light when they are off; this is a normal condition, and must be kept in mind.- Take note of the following:
...VR that may be used in the field.
...VR that must not be used in the field.
15.2.9.2 DC Controller PCB0015-5396
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
J725J715
J108
J130
J1041J1031
J1030
J726
J1040
J2109
J5770
J577
J5500
J550J4006
J4003
J4009
J718
J1401
J101
J111
J125
J719
J325
J702
J124
J251
J1404
J902
J903
J108
J107
J322
J6310J6320
J632
J631
J602J713 J601
J222
J901
J137
J1543
J321
J1415
J4004
J4005
J1414
J138
100V 3031120V 3032230V 3033
J131
Chapter 15
15-26
F-15-21- J303
When replacing the PCB, be sure to move the J303 shorting connector from the existing to new PCB. The control panel indications will fail to appear unless the shorting connector has been connected properly.
- CP33Use it when checking the potential system.
- VR3for factory use
15.2.9.3 DC Power Supply PCB0015-5398
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-15-22- VR4501, VR4601, VR4605, VR4701
for factory use
15.2.9.4 HVT PCB0015-5399
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
J110
J113
J111
J109
J107 J112 J104 J105 J115 J102
J101
J119
J106
J118
J128
J123
J108
J19J117J304J121
J203
J100
J125
B1
B17
B1
B13
B1
B10
13
A1
A17
A1
A1
A1 A9 A1 A15
7 1
A1 A16 A1
81
14
A20 B1
21
J3
15
A1
1
J124
109
1
J131
1 8
J130
1 16
J114
15
1412191 4
J116
1 8
A1
A13
A1
A10
J103
B1B20
A1 A20
B13
B1
B20
B1
B10
A18
B1 B1 B15 B1 B16B1 B9 B1 B20
A20 A1
A18
71
A13
B1
B13 A1
A13
B40
B1
A1
A40
A10
J303
VR3
CP33
1 12
2
5
1
1
1 10
7
8
1
1
1 4
1 4 1
1
1
1 2
3
6
4
1 6 1 4
2 13 1
5 1
13
J4011
J4015
J4008
J4016
J4004
CN
4001
J4001-2
J4001-1
J4007
J4006
J4005
J4017
J4003
J4014
J4009
J4010J4002
J4013
J4019
VR4501
VR4701
VR4601
VR4605
Chapter 15
15-27
F-15-23- VR4501
for factory use
1 13 1 2
15
13
J4502
J4501
VR4501
J4503
J4509
J450
5
J4508J4507 T4505 T4506J4506J4504
Chapter 16 Self Diagnosis
Contents
Contents
16.1 Error Code Table........................................................................................................................................................16-116.1.1 Error Code................................................................................................................................................................................ 16-1
16.2 Error Code Details .....................................................................................................................................................16-216.2.1 Detail Error Code ..................................................................................................................................................................... 16-216.2.2 E602 in Detail ........................................................................................................................................................................ 16-15
16.3 Error Code (SEND)..................................................................................................................................................16-1716.3.1 Results of Self-Diagnosis....................................................................................................................................................... 16-1716.3.2 Error Codes ............................................................................................................................................................................ 16-19
16.4 Jam Code..................................................................................................................................................................16-2416.4.1 Jam Code (machine proper) ................................................................................................................................................... 16-2416.4.2 Jam Code (finisher-related).................................................................................................................................................... 16-2416.4.3 Jam Code (ADF-related)........................................................................................................................................................ 16-25
16.5 Alarm Code ..............................................................................................................................................................16-2616.5.1 Alarm Code ............................................................................................................................................................................ 16-26
Chapter 16
16-1
16.1 Error Code Table
16.1.1 Error Code0015-5623
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-1
Code DescriptionE000 the heater fails to heatE001 there is an abnormal rise in temperatureE002 there is an error in the rise in temperatureE003 there is an error in the rise in temperatureE004 there is an error in the IH power supply/IH control mechanismE005 there is no fixing web/there is an error in the detection of web solenoid connectionE010 there is a feed motor errorE012 there is a drum motor errorE013 the collecting toner pipe is cloggedE014 there is a fixing motor errorE020 there is no toner in the developing assembly; there is an error in the detection of developing assembly toner sensor connection; there is an error in
the detection of developing hopper toner sensor connection
E025 there is an error in the detection of toner feed motor over-current, there is an error in the detection of toner bottle motor over-current, there is an error in the detection of toner bottle motor connection
E032 the counter of the NE controller has malfunctioned
E061 there is a potential control error/there is an APC errorE100 there is a BD errorE102 there is a laser verify error
E110 there is a polygon motor errorE121 there is a controller cooling errorE193 there is a gate array error
E196 the EEPROM is faultyE197 there is an error in communication between the DC controller PCB and the video PCB/an error in communication of the DC controller PCB
E225 Error in CIS Unit (DADF)
E240 there is an error in the communication between the main controller PCB and the DC controller PCBE315 there is an image data error
E503 there is a finisher internal communication error (finisher)E505 there is a backup memory error in the finisher (finisher)E514 there is a trailing edge assist motor error (finisher)E519 there is a gear change motor error (finisher)E530 there is a front alignment error (finisher)E531 there is a staple error (finisher)E532 there is a stapler shift error (finisher)E535 there is a swing error (finisher)E537 there is a rear alignment error (finisher)E540 there is an upper tray ascent/descent error (finisher)E542 there is a lower tray ascent/descent error (finisher)E584 there is a shutter unit error (finisher)E590 there is a punch motor error (punch unit)E591 there is a punch dust sensor error (punch unit)E592 there is a punch horizontal registration sensor error (punch unit)E593 there is a punch shift motor error (punch unit)E5F0 there is a saddle paper positioning errorE5F1 there is a saddle paper folding errorE5F2 there is a saddle guide errorE5F3 there is a saddle alignment errorE5F4 there is a saddle rear staple errorE5F5 there is a saddle front staple errorE5F6 there is a saddle butting errorE5F9 there is a saddle switch errorE602 error in hard disk or HDD encryption boardE604 the image memory is faulty or inadequateE609 the hard disk is faultyE610 the HDD encryption key is faultyE611 retried reboot due to SRAM crash and the like during the shutdown recovery job execution
Chapter 16
16-2
16.2 Error Code Details
16.2.1 Detail Error Code0015-5625
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-2
E612 error in postponement
E674 There is a fault in the communication between the fax controller PCB (2-line) and the main controller PCB.
E710 there is a printer IPC errorE711 there is a printer IPC errorE713 there is a sorter IPC errorE717 the communication with the NE controller is faulty
E719 the coin vendor is faulty
E730 the PDL software is faulty
E732 there is a reader communication error
E733 the printer communication is faulty
E740 the Ethernet board is faulty
E744 the language file/boot ROM is faulty
E746 the accessories board type is wrong
E748 the controller board do not match
E804 there is a DC power supply fan error/there is an IH power supply cooling fan errorE805 there is a heat discharge fan error/there is a feed fan errorE808 there is a IH power supply input error
E821 the cleaner is cloggedE824 there is a primary charging cooling fan errorE840 there is a shutter errorE841 there is an error in the detection of fixing inlet guide solenoid connection
Code Description Remedy
E000 The heater fails to heat.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0000 After power-on, the reading of the main thermistor does not increase to 70 deg C or higher within 20 sec.
- Replace the main/shutter thermistor.- Replace the DC controller PCB.
0010 The power has been turned off and then on without resetting the error. - Reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E001 There is an abnormal rise in temperature.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001 There is an error or an open circuit in the main thermistor, shutter thermistor, or sub thermistor.
- Check the connector of each thermistor for any fault in connection and wiring.- Replace the thermistor in question.- Replace the DC controller PCB.
0002 The reading of the main thermistor, shutter thermistor, or sub thermistor is 230 deg C or higher for 2 sec.
- Replace the thermistor in question.- Replace the DC controller PCB.
0003 The reading is not 150 deg C or higher or 210 deg C or lower within 30 sec. -Cheak the connecting of the main/ sub/ shutter thermistors.-Check the mounting of the main/ sub/ shutter thermistors.-Exchange the main/ sub/ shutter thermistors.-Exchange the DC controller PCB.
0010 The power has been turned off and then back on without resetting the error. - Reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E002 There is an abnormal rise in temperature.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
Code Description
Chapter 16
16-3
0000 The reading of the main thermistor is not 100 deg C 12 sec after it has exceeded 70 deg C.
- Check the connector of the main/shutter thermistor for any fault in connection and wiring.- Check the main/shutter thermistor for mounting condition.- Replace the main/shutter thermistor.- Replace the fixing heater unit.- Replace the DC controller PCB.0001 The reading of the main thermistor is not 150 deg C 15 sec after it has
exceeded 100 deg C.
0010 The power has been turned off and then back on without resetting the error. - Reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E003 There is an abnormal rise in temperature.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0000 The reading of the main thermistor is lower than 70 deg C for 2 sec or more after it has exceeded 100 deg C.
- Check the connector of the main/shutter thermistor for any fault in connection and wiring.- Check the main/shutter thermistor for mounting condition.- Replace the main/shutter thermistor.- Replace the fixing heater unit.- Replace the DC controller PCB.
0010 The power has been turned off and then back on without resetting the error. - Reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E004 The IH power supply is faulty/the IH control mechanism is faulty.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0010 The power has been turned off and then back on without resetting the error. - Reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0101 There is a mismatch between the input voltage and the IH power supply ID. Replace the fixing heater power supply with one designed for the country of installation (voltage).
0102 The IH current is faulty. (current leakage) - Check the connector for any fault in connection.- Replace the fixing heater power supply.- Replace the DC controller PCB.0103 The IH current is faulty. (no current)
0104 There is an IH over-current.0105 The IH input voltage is too high.0106 The IH input voltage is too low.0201 At power-on (or, when IH is at reset), the IH control mechanism is not in
an initial state.
0202 At IH start-up, the IH control enable flag is not set within 1 sec after the start flag is set.
0203 With IH at rest, the IH control flag is not released.
0204 The 12-V power supply (IH relay) is identified as being off.
0205 At IH start-up, the PWM/ON data is faulty ('0' or 'FFFF') - Replace the DC controller PCB.
E005 There is no fixing web/there is an error in the detection of web solenoid connection.0000 The absence of the fixing web has been detected for 5 sec or more. - Replace the fixing web.
- Replace the fixing web length sensor.- Replace the DC controller PCB.After correcting the fault, be sure to reset the fixing web counter reading. (COPIER>COUNTER>MISC>FIX-WEB)
0001 At power-on, the connection of the web solenoid is not detected. - Check the connector for any fault in connection.- Replace the solenoid.
0010 The power has been turned off and then back on without resetting the error. - Reset the fixing web counter. (COPIER>COUNTER>MISC>FIX-WEB)
E010 There is a feed motor error.0000 The FG signal of the feed motor does not arrive for 2 sec or more even
when the feed motor has been turned on.- Check the connector for any fault in connection.- Replace the motor
E012 There is a drum motor error.0000 The FG signal of the drum motor does snot arrive for 2 sec or more even
when the drum motor has been turned on.- Check the connector for any fault in connection.- Replace the motor.
Code Description Remedy
Chapter 16
16-4
E013 The waste toner pipe is clogged.0000 The waste toner pipe is identified as being clogged for 4 sec or more. - Check the connector for any fault in connection.
- Replace the waste toner feedscrew lock detecting switch.- Replace the waste toner feed unit.- Replace the DC controller PCB.
0010 The power has been turned off and then back on without resetting the error.
E014 There is a fixing motor error.0000 The Phase lock signal of the fixing motor does not arrive for 2 sec even
when the fixing motor has been turned on.- Check the connector for any fault in connection.- Replace the motor.
E020 There is no toner in the developing assembly; there is an error in the detection of developing toner sensor connection; there is an error in the detection of hopper toner sensor connection
0000 The presence of toner is detected inside the sub hopper and, in addition, the absence of toner is detected inside developing assembly for 120 sec continuously even when operation has been under way for the supply of toner to the developing assembly.
- Check the connector of the developing toner sensor for any fault in connection.- Replace the developing toner sensor.- Replace the hopper toner sensor.
0001 At power-on, the connection of the developing assembly toner sensor is not detected.
- Check the connector for any fault in connection.- Replace the sensor.
0002 At power-on, the connection of the developing hopper toner sensor is not detected.
- Check the connector for any fault in connection.- Replace the sensor.
E025 There is a toner feed motor over-current detection error, there is a toner bottle motor connection detection error.
0001 An over-current has been detected in the toner feed motor. - Check the connector for any fault in connection.- Replace the motor.
0002 An over-current has been detected in the toner bottle motor. - Check the connector for any fault in connection.- Replace the motor.
0003 At power-on, the connection of the toner bottle motor is not detected. - Check the connector for any fault in connection.- Replace the motor.
E032 The NE controller counter has malfunctioned.
0001 An open circuit has been detected for the count pulse signal. Turn off the main power, and check for an open circuit in the cable; then, turn the main power back on.
E061 There is a potential control error/there is an APC error.0001 As a result of potential control, the drum surface potential (VL2) of the
background is 200 V or higher (i.e., causing a solid black image).- Replace the potential sensor unit.- Replace the laser scanner unit.- Replace the DC controller PCB.
0002 The primary charging output used at time of printer output and the drum surface potential after laser output is identified as being 200 V or more (i.e., causing a solid black image).
E100 There is a BD error.0001 A check is made of VLOCK at intervals of 100 msec while the laser is on.
An error will be identified if it is not detected 10 times in sequence.- Replace the laser scanner unit.- Replace the DC controller PCB.
E102 There is a laser verify error.
0001 The machine model ID that has been read from the laser scanner EEPROM is not correct.
E110 There is a polygon motor error.
Code Description Remedy
Chapter 16
16-5
0001 - Although the polygon motor has been turned on, VLOCK is not detected at all within 76.5 sec.- At time of a shift from full-speed to half-speed control, VLOCK is not detected at all for 7.5 sec.- At time of half-speed control, a check is made of VLOCK at intervals of 100 msec. An error will be identified if it is not detected 10 times continuously.
- Replace the laser scanner unit.- Replace the DC controller PCB.
E121 There is a controller cooling fan error.
0001 Even though the controller cooling fan has been turned on, the controller cooling fan stop signal has been detected for 5 sec or more.
- Check the connector for any fault in connection.- Replace the fan.
E193 There is a gate array error.
0001 The add-on through setting of the IMGI cannot correctly be done (it is not correctly set 10 continuous times)
E196 The EEPROM is faulty.1abb There is a mismatch between the data that has been written in EEPROM
and the data that has been read. (a: chip No. 0 through 5; bb: chip faulty address)
- Initialize the RAM.- Replace the EEPROM.- Replace the DC controller PCB.
2abbThe ID in EEPROM that has been read and the ID in ROM are compared. An error will be identified if they do not match. (a: chip No. 0 through 5; bb: chip faulty address)
3abb When the main power is turned on, the ID in EEPROM and the ID in ROM are compared. An error will be identified if they do not match. (a: chip No. 0 through 5; bb: chip faulty address)
- Check the position and condition of the EEPROM.- Initialize the RAM.- Replace the EEPROM.- Replace the DC controller PCB.
E197 There is an error in communication between the DC controller PCB and the video PCB/an error in communication of the DC controller PCB.
0000 An error in the communication between the DC controller PCB and the video PCB has occurred.
0001 An error in the communication with the laser driver module of the DC controller PCB has occurred.
E225 Error in CIS Unit (DADF)
1010 - The error is cleared by turning off/on the power switch. This triggers function-restricted mode.- CIS unit suspends its functions; only CCD unit performs duplexing reading.- Functions will be automatically restored by replacing CIS unit.
E240 The communication between the main controller PCB and the DC controller PCB is faulty.
0000 There is an error in the communication between the main controller PCB and the CPU of the DC controller PCB.
- Check the connector for any fault in connection.- Replace the DC controller PCB.- Replace the main controller PCB.
E315 There is a fault in the image data.
0007 There is a JIBIG encode error. - Turn off and then back on the power.
000d There is a JBIG decode error.
0200 CRC error detected in OpenI/F (image transfer from the external controller); retried but failed to restore.
- Replace the external controller connection PCB
0300 Cubic timeout - Turn off/on the power switch. Replace the PCB for frequent error occurrence.
0400 Shift device A timeout
0401 Shift device B timeout
E503 There is an error in the finisher internal communication (finisher).0002 There is an error in the communication between the finisher and the saddle
unit.- Check the connection between the saddle stitcher controller PCB and the finisher controller PCB.
Code Description Remedy
Chapter 16
16-6
0003 There is an error in the communication between the finisher and the punch unit.
- Check the communication between the saddle stitcher controller PCB and the finisher controller PCB.
E505 There is a finisher backup memory error (finisher).0001 An error has occurred in the data stored in the backup memory. - Turn off the main power; check the DC controller PCB and the finisher
controller PCB for wiring; check the 24-V system fuse; then, turn the main power back on.
0002 There is an error in the punch unit EEPROM data. - Turn off the main power; check the DC controller PCB and the puncher controller PCB for wiring; then, check the 24-V system fuse; then, turn the main power back on.
E514 There is a trailing edge assist motor error (finisher).
8001 The home position sensor does not go off even when the trailing edge assist motor has rotated for a specific period of time.
1. Check the trailing edge assist home position sensor. Is the sensor normal?2. Check the wiring between the finisher controller PCB and the trailing edge assist motor. Is it normal?3. Check the trailing edge assist mechanism. Is there a fault?4. Try replacing the trailing edge assist motor. Is the problem corrected?
8002 The home position sensor does not go on even when the trailing edge assist motor has rotated for a specific period of time.
E519 There is a gear change motor error (finisher).8001 The home position sensor does not go off even when the gear change motor
has rotated for a specific period of time.1. Check the gear change home position sensor. Is the sensor normal?2. Check the wiring between the finisher controller PCB and the change motor. Is it normal?3. Check the gear change mechanism. Is there a fault?4. Try changing the gear change motor. Is the problem corrected?
0002 The home position sensor does not go on even when the gear change motor has rotated for a specific period of time.
E530 There is a front alignment error. (finisher)8001 The home position sensor does not go off even when the front alignment
motor has rotated for a specific period of time.1. Check the aligning plate home position sensor. Is it normal?2. Check the wiring between the finisher controller PCB and the aligning plate front motor. Is it normal?3. Is there any mechanical obstacle in the path in which the aligning plate moves?4. Try replacing the aligning plate front motor. Is the problem corrected?
8002 The home position sensor does not go on even when the front alignment motor has rotated for a specific period of time.
E531 There is a stapling error. (finisher)
Code Description Remedy
Chapter 16
16-7
0001 The home position sensor does not go off even when the stapler motor has rotated for a specific period of time.
1. Check the wiring between the finisher controller PCB and the stapler. Is it normal?2. Try replacing the stapler. Is the problem corrected?
0002 The home position sensor does not go on even when the stapler motor has rotated for a specific period time.
E532 There is a stapler shift error. (finisher)8001 The home position sensor does not go off even when the stapler shift motor
has rotated for a specific period of time.1. Check the stapler shift home position sensor. Is the sensor normal?2. Check the wiring between the finisher controller PCB and the stapler shift motor. Is it normal?3. Is there any mechanical obstacle in the path of the stapler shift base?4. Try replacing the stapler shift motor. Is the problem corrected?
8002 The home position sensor does not go on even when the stapler shift motor has rotated for a specific period of time.
E535 There is a swing error. (finisher)8001 The home position sensor does not go off even when the swing motor has
rotated for a specific period of time.1. Check the swing home position sensor. Is it normal?2. Check the wiring between the finisher controller PCB and the swing motor. Is it normal?3. Is there a fault in the swing mechanism?4. Try replacing the swing motor. Is the problem corrected?
8002 The home position sensor does not go on even when the swing motor has rotated for a specific period of time.
E537 There is a rear alignment error. (finisher)8001 The home position sensor does not go off even when the swing motor has
rotated for a specific period of time.1. Check the aligning plate rear home position sensor. Is it normal?2. Check the wiring between the finisher controller PCB and the aligning plate rear motor. Is it normal?3. Is there a mechanical obstacle in the path of the aligning plate?4. Try replacing the aligning plate rear motor. Is the problem corrected?
8002 The home position sensor does not go on even when the swing motor has rotated for a specific period of time.
E540 There is an upper tray ascent/decent error. (finisher)
Code Description Remedy
Chapter 16
16-8
8001 - If the tray does not return to home position when the tray 1 shift motor is driven for 20 seconds.- If the tray does not move to other area when tray 1 shift motor is driven for 4 seconds.
1. Check the No. 1 tray area sensors 1 through 3. Are they normal?2. Check the wiring between the finisher controller PCB and the No. 1 tray shift motor. Is it normal?3. Is there a fault in the tray ascent/descent mechanism?4. Try replacing the No. 1 tray shift motor. Is the problem corrected?8002 - The dangerous area is reached before the tray 1 paper surface sensor
detects paper surface during the paper surface detection operation.- A discontinuous area is detected during tray operation.
8003 The tray 1 closing detect switch is activated while the tray 1 is operating.
8004 Clock signal input cannot be detected when the tray 1 shift motor has been driven for 0.2 second.
8005 The lock detection signal turns OFF 150 ms after the lock detection signal turned ON.
8006 The lock detection signal does not turn ON when the tray 1 shift motor has been driven for 1 second.
8007 The lock detection signal does not turn OFF when the tray 1 shift motor is at a stop.
E542 There is a lower tray ascent/descent error. (finisher)8001 There is a fault in the lower tray ascent/descent motor clock signal. 1. Check the No. 2 tray area sensors 1 through 3. Are the sensors normal?
2. Check the wiring between the finisher controller PCB and the No. 2 tray shift motor. Is it normal?3. Is there a fault in the tray ascent/descent mechanism?4. Try replacing the No. 2 tray shift motor. Is the problem corrected?
8002 There is an area error.
0003 The safety switch has activated.
E584 There is a shutter unit error. (finisher)
8001 The shutter open sensor fails to go off. (The shutter does not close.) 1. Check the shutter home position sensor. Is it normal?2. Check the wiring between the finisher controller PCB and the stack feeding motor and between the finisher controller PCB and the shutter open/close clutch. Is it normal?3. Is there a fault in the shutter mechanism?4. Try replacing the stack edging motor and the shutter open/close clutch. Is the problem corrected?
0002 The shutter open sensor does not go on. (The shutter does not open.)
E590 There is a punch motor error. (punch unit)8001 The punch home position sensor is not detected even when the punch motor
has been driven for 200 msec.- Check the punch home position sensor, horizontal registration motor, and punch driver PCB; thereafter, turn off and then back on the main power.
8002 The puncher does not detect the punch home position sensor while the motor is at rest at time of punch motor initialization.
E591 There is a punch dust sensor error. (punch unit)8001 The incoming light voltage is faulty in the presence of light. - Turn off and then back on the main power.
8002 The incoming light voltage is faulty in the absence of light.
E592 There is a punch horizontal registration sensor error. (punch unit)
Code Description Remedy
Chapter 16
16-9
8001 The incoming light voltage is faulty in the presence of light. (trailing edge sensor)
- turn off and then back on the main power.
8002 The incoming light is faulty in the absence of light and voltage. (trailing edge sensor)
8003 The incoming light voltage is faulty in the presence of light. (horizontal registration sensor 1)
8004 The incoming light voltage is faulty in the absence of light. (horizontal registration sensor 1)
8005 The incoming light voltage is faulty in the presence of light. (horizontal registration sensor 2)
8006 The incoming light voltage is faulty in the absence of light. (horizontal registration sensor 2)
8007 The incoming light voltage is faulty in the presence of light. (horizontal registration sensor 3)
8008 The incoming light voltage is faulty in the absence of light. (horizontal registration sensor 3)
8009 The incoming light voltage is faulty in the presence of light. (horizontal registration sensor 4)
800A The incoming light voltage is faulty in the absence of light. (horizontal registration sensor 4)
E593 There is a punch shift motor error. (punch unit)8001 In the presence of light, the incoming light voltage HP sensor does not go
off.- Turn off and the back on the main power.
8002 In the absence of light, the incoming light voltage HP sensor does not go on.
E5F0 There is a saddle paper positioning error.0001 The paper positioning plate home position sensor does not go on even when
the paper positioning plate motor has been driven for 1.33 sec.paper positioning plate motor (M4S), paper positioning plate home position sensor (PI7S)
- Check the paper positioning plate motor (M4S) and the paper positioning plate home position sensor (PI7S).
0002 The paper positioning plate home position sensor does not go off even when the paper positioning plate motor has been driven for 1 sec.paper positioning plate motor (M4S), paper positioning plate home position sensor (PI7S)
E5F1 There is a saddle paper folding error.0001 The number of detection pulses of the paper folding motor clock sensor is
lower than a specific value.paper folding motor (M2S), paper folding motor clock sensor (PI4S)
- Check the paper folding motor (M2S) and the paper folding motor clock sensor (PI4S).
0002 The state of the paper folding home position sensor does not change even when the paper folding motor has been driven for 3 sec.paper folding motor (M2S), paper folding motor clock sensor (PI4S)
E5F2 There is a saddle guide error.0001 The guide home position sensor does not go on even when the guide motor
has been driven for 0.455 sec.guide motor (M3S), guide home position sensor (PI13S)
- Check the guide motor (M3S) and the guide home position sensor (PI13S).
0002 The guide home position sensor does not go off even when the guide motor has been driven for 1 sec.guide motor (M3S), guide home position sensor (PI13S)
Code Description Remedy
Chapter 16
16-10
E5F3 There is a saddle alignment error.0001 The aligning plate home position sensor does not go on even when the
aligning motor has been driven for 0.5 sec. (if at time of initialization, 1.67 sec)alignment motor (M5S), aligning plate home position sensor (PI5S)
- Check the alignment motor (M5S) and the aligning plate home position sensor (PI5S).
0002 The aligning plate home position sensor does not go off even when the aligning motor has been driven for 1 sec.alignment motor (M5S), aligning plate home position sensor (PI5S)
E5F4 There is a saddle rear stapler error.
0001 The stitching home position sensor does not go on even when the stitching motor (rear) has been driven in reverse for 0.5 sec or more.stitching motor (rear, M6S), stitching home position sensor (rear, MS5S)
- Check the stitching motor (rear, M6S) and the stitching home position sensor (rear, MS5S).
0002 the stitching home position sensor does not go off even when the stitching motor (rear) has been driven in normal direction for 0.5 sec or more.stitching motor (rear, M6S), stitching home position sensor (rear, MS5S)
E5F5 There is a saddle front stapling error.0001 The stitching home position sensor does not go on even when the stitching
motor (front) has been driven in reverse for 0.5 sec or more.stitching motor (front, M7S), stitching home position sensor (front, MS7S)
- Check the stitching motor (front, M7S) and the stitching home position sensor (front, MS7S).
0002 The stitching home position sensor does not go off even when the stitching motor (front) has been driven in normal direction for 0.5 sec or more.stitching motor (front, M7S), stitching home position sensor (front, MS7S)
E5F6 There is a saddle butting error.8001 The paper pushing plate home position sensor does not go on even when
the paper pushing plate motor has been driven for 0.3 sec or more.paper pushing plate motor (M8S), paper pushing plate home position sensor (PI14S)
- Check the paper pushing plate motor (M8S) and the paper pushing plate home position sensor (PI14S).
8002 The paper pushing plate home position sensor does not go off even when the paper pushing plate motor has been driven for 80 msec.paper pushing plate motor (M8S), paper pushing plate home position sensor (PI14S)
8003 The number of detection pulses of the paper pushing plate motor clock sensor is lower than a specific value.paper pushing plate motor (M8S), paper pushing plate motor clock sensor (PI1S)
- Check the paper pushing plate motor (M8S) and the paper pushing plate motor clock sensor (PI1S).
Code Description Remedy
Chapter 16
16-11
8004 The paper pushing plate leading edge sensor does not go off even when the paper pushing plate motor has been driven for 80 msec.paper pushing plate motor (M8S), paper pushing plate leading edge position sensor (PI15S)
- Check the paper pushing plate motor (M8S) and the paper pushing plate leading edge position sensor (PI15S).
8005 The paper pushing plate leading edge position sensor does not go on even when the paper pushing plate has been driven for 0.3 sec or more.paper pushing plate motor (M8S), paper pushing plate leading edge position sensor (PI15S)
E5F9 There is a saddle switch error.0001 With any of the sensor identifying its respective cover as being closed, the
inlet cover switch is identified as being open for 1 sec from the start of initial rotation or printing:- inlet cover sensor (PI9S)- front cover open/closed sensor (PI2S)- delivery cover sensor (PI3S)Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open.inlet cover switch (MS1S), front cover switch (MS2S), delivery cover switch (MS3S)
- Check the inlet cover switch (MS1S), front cover switch (MS2S), and the delivery cover switch (MS3S).
0002 With any of the following sensors identifying its respective cover as being closed, the front cover switch is identified as being open for 1 sec or more after the start of initial rotation or printing.- inlet cover sensor (PI9S)- front cover open/closed sensor (PI2S)- delivery cover sensor (PI3S)- front cover switch (MS2S), delivery cover switch (MS3S)
- Check the front cover switch (MS2S) and the delivery cover switch (MS3S).
0003 With any of the following sensors identifying its respective cover as being closed, the delivery cover switch is identified as being open for 1 sec or more from the start of initial rotation or printing:- inlet cover sensor (PI9S)- front cover open/closed sensor (PI2S)- delivery cover sensor (PI3S)- delivery cover switch (MS3S)
- Check the delivery cover switch (MS3S).
E602 error in hard disk or HDD encryption board0001 [Cause] HD detection error: the HD cannot be detected; the machine fails
to turn ready; an error state is returned.[Description] at time of Bootrom processing, BARSAC is started up and mounted (usrIde).[Timing] once at power-on
- See details for E602.
0002 [Cause] start-up file absent: the main CPU program does not exist on the HD (/BOOTDEV/BOOT/and lower).[Description] at time of Bootrom processing, when the system files are being loaded (usrIde).[Timing] once at start-up
- See details for E602.
0003 [Cause] HD write abort error: /BOOTDEV sector on the HD cannot be read.[Description] BARSAC (all areas at Bootable start-up)[Timing] once at start-up
- See details for E602.
0006 [Cause] SubBootable compatible with the PDL type does not exist in /BOOTDEV/BOOT.[Description] when SubBoot in oclibroot is being loaded[Timing] once at start-up of Bootable
- See details for E602.
Code Description Remedy
Chapter 16
16-12
0007 [Cause] ICC-Profile compatible with the PDL type does not exist in /BOOTDEV/PDL.[Description] beginning of oclibroot; the PDL team function is called and determined[Timing] once at start-up of Bootable
- See details for E602.
2000 error in the authentication between the host machine and the encryption board
- Check the encryption board connection, plug off/in the connector and turn off/on the power switch.- Perform the key-clear.
2001 error in alignment of the encryption board operation - Perform the key-clear.
2002 the encryption board failure, etc. - Check the encryption board connection, plug off/in the connector and turn off/on the power switch.- Perform the key-clear.- Replace the encryption board and reinstall the HDD format and SYSTEM of SST- Replace LAN-BARSAC board -> replace the main board
01XX /FSTDEV is faulty. - See details for E602.02XX /IMG_MNG is faulty. - See details for E602.03XX /FSTCDEV is faulty. - See details for E602.04XX /APL_GEN is faulty. - See details for E602.05XX /TMP_GEN is faulty. - See details for E602.06XX /TMP_FAX is faulty. - See details for E602.07XX /TMP_PSS is faulty. - See details for E602.08XX /PDLDEV is faulty. - See details for E602.09XX /BOOTDEV is faulty. - See details for E602.10XX /APL_MEAP is faulty. - See details for E602.
11XX /APL_SEND is faulty. - See details for E602.
12XX /APL_KEEP is faulty. - See details for E602.
13XX /APL_LOG is faulty. - See details for E602.
FFXX There is an error in a partition that cannot be identified. - See details for E602.
E604 The image memory is faulty or inadequate.
0000 The memory is inadequate for the model. - Add memory.E609 The hard disk is faulty.
0008 At time of start-up, the HDD fails to reach a specific temperature within a specific period of time.
- Replace the hard disk.- Replace the DC controller PCB.
0009 At time of a sleep shift, the temperature is below a specific level.
E610 The HDD encryption key is faulty. (hardware composition error, initialization error, ID key error, ID processing error)0001 There is no encryption board. - Check the hardware composition.
0002 The memory configuration is inadequate for the use of encryption.
0101 The attempt to initialize the memory used for storage of the key has failed. - Turn off and then on the main power.
0102 The attempt to initialize the encryption processing area has failed.
0201 There is an error in the encryption processing area.
0202 There is an error in the encryption processing area.
0301 The attempt to create an ID key has failed.
0302 A fault has been detected in the encryption key. - Turn off and then on the main power.This error will reset all content on the HDD.
0303 A fault has been detected in the encryption key.
Code Description Remedy
Chapter 16
16-13
0401 An error has been detected at time of coding. - Turn off and then on the main power.
0402 An error has been detected at time of decoding.
0501 error in the document management information on /FSTDEV
E611 retried reboot due to SRAM crash and the like during the shutdown recovery job execution
0000 SRAM data were broken and the stored job information cannot be read; this causes the repeated reboot trials to recover the power shutdown, and thus the redundant job transmission. This phenomenon triggers E code.
Clear SRAM to cancel the shutdown recovery job.
E612 error in postponementTiming: when starting the host machine
0000 other errorsUnlikely errors except the errors shown belowWrite the correct license and new serial numbers and turn off/on the power switch.
Write the correct license and new serial numbers and turn off/on the power switch.
0001 error in the license checksumUnmatched license checksum
0002 error in the machine codeDifferent machines are specified by the old and new machine codes, respectively.
0003 error in the new serial numberNo data is entered in the new serial number field
0004 error in old serial numbersThe license serial number is unmatched with SoftID
0005 error in postponementThe license is written although postponement has already been performed once.
- Turn off and then on the main power.
E674 There is a fault in the communication between the fax controller PCB (2-line) and the main controller PCB.
0001 An attempt to set fax device mode has failed. - Check the connection of the cable between the fax controller PCB (2-line) and the main controller PCB.- Replace the ROM DIMM of the fax controller PCB (2-line).- Replace the fax controller PCB (2-line).- Replace the main controller PCB.
E710 There is a fault in IPC initialization.
0001 At time of power-on, the communications IC on the main controller PCB does not become ready within 3 sec after start-up.
- Check the connection of the cable.
0002 At power-on, the machine communication IC has detected an error.
E711 There is a fault in the IPC communication.
0001 After power-on, the occurrence of an error has been written 4 times in 1.5 sec to the error register of the communications IC on the main controller PCB.
- Check the connection of the cable.
0002 After power-on, the machine communication IC has detected an error.
E713 There is a sorter IPC error.0000 An error has been detected in the sorter communication IC. - Check the connection of the cable.
- Replace the finisher controller PCB.- Replace the DC controller PCB.
E717 There is a fault in the communication with the NE controller.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001 An error has occurred at time of NE controller start-up.The NE controller that was connected before power-off is not connected at power-on.
- Check the connection of the cable.
0002 There is an IP error while the NE controller is in operation.The IPC may have an open circuit or the IPC communication cannot be recovered.
E719 There is a fault in the coin vendor.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
Code Description Remedy
Chapter 16
16-14
0001 An error has occurred at time of coin vendor start-up.The coin vendor was connected before power-off, but is not connected at power-on.
- Check the connector of the cable.
0002 An IPC error has occurred while the coin vendor is in operation.The IPC may have an open circuit, or the IPC communication cannot be recovered.The pickup/delivery signal line has an open circuit.An illegal connection has been detected.
0003 While a unit price is being obtained at start-up, an error has occurred in the communication with the coin vendor.
0011 An error has occurred at card reader start-up.The card reader that was connected before power-off is not connected at power-on.
0012 An IPC error has occurred while the card reader is in operation.The IPC may have an open circuit, or the IPC communication cannot be recovered.
E730 There is a fault in the PDL software.
1001 There is an initialization error. - Execute PDL resetting.- Turn off and then on the main power.
100A An error has occurred that can be fatal to the system (e.g., initialization error).
9004 There is a fault in the PAI communication with an outside controller. - Turn off and then back on the main power.- Check the open I/F board and cable connection.- Replace the external controller open I/F board.- Replace the main controller PCB.
9005 There is a fault in video connection with an external controller.
A006 absence of PDL response: there is no PDL response because of a fault in or the absence of Subbootable.
- Execute PDL resetting.- Turn off and then on the main power.- Check the connection of the SURF board.- Re-install the firmware.- Replace the main controller PCB.
A007 There is a mismatch in version between the machine control software and the PDL control software.
- Execute PDL resetting.- Turn off and then on the main power.- Execute full formatting and install the system software.
B013 The font data is corrupted. - Turn off and then on the main power.- Re-install the system software.- Execute full formatting and install the system software.
E732 error in reader communication0001 There is a communication error between the reader and main controller
(DDI-S communication error), or between the reader and the charger unit.- Check the communication between the reader unit and the main controller.- Check the power supply of the reader unit. (Check to see if initialization takes place at start-up.)- Replace the reader controller PCB, reader relay PCB, or main controller PCB.- Check the connection of the charger unit. (iR5075/5075N only.)
8888 error in difference of scanner - check the scanner model- in service mode, select: COPIER > OPTION > BODY > SCANTYPE to check
E733 There is a fault in the printer communication.
0000 The attempt at communication with the printer fails at start-up. - Check the connection of the cable between the DC controller and the main controller.- Check the power supply of the printer. (Check to see if initialization takes place at start-up.)- Replace the DC controller PCB or the main controller PCB.
0001 There is a DDI-P communication error.
E740 There is a fault in the Ethernet board.
0002 The MAC address is illegal. - Replace the main controller PCB.
E744 There is a fault in the language file/boot ROM.
0001 There is a mismatch between the language version on the HDD and the version of Bootable.
- Download the language file of the correct version.
0002 The size of the language file on the HDD is too big.
0003 There is no language file that is described in CONfig.txt on the HDD.
0004 A switchover to a language file on the HDD cannot be made.
1000 The boot ROM in question is one designed for a different model. - Replace the boot ROM with one of the appropriate version.
2000 The engine ID is illegal. - Turn off and then on the main power.
E746 There is an error caused by a mismatch of the accessories board.
0003 At start-up, a UFR board for a different model has been detected. - Replace the UFR board with one for the model in question.
Code Description Remedy
Chapter 16
16-15
16.2.2 E602 in Detail0015-5627
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<E602-XXYY>
- XX= '00'
E748 error in controller board
4910 error in detection of the controller plate differs from the equipment - Replace the main controller PCB.
E804 There is a DC power supply fan error/there is an IH power supply cooling fan error.0000 The DC power supply fan stop signal has been detected for 5 sec or more
even when the DC power fan is on.- Check the connection of the connector.- Replace the fan.
0001 The IH power supply cooling fan stop signal has been detected for 5 sec or more even when the IH power supply cooling fan is on.
- Check the connection of the connector.- Replace the fan.
0002 The accessories power supply cooling fan stop signal has been detected for 5 sec or more even when the accessories power supply cooling fan is on.
- Check the connection of the connector.- Replace the fan.
E805 There is a heat discharge fan error/there is a feed fan error.0001 The heat discharge fan stop signal has been detected for 5 sec or more even
when the heat discharge fan is on.- Check the connection of the connector.- Replace the fan.
0002 The feed fan stop signal has been detected for 5 sec even when the feed fan is on.
- Check the connection of the connector.- Replace the fan.
E808 IH power supply input errer
0001 The IH power supply input voltages are higher than the stipulated voltages - Connect with the outlet of a correct voltage.- Check the connection of the connector.- Replace the fixing heater power supply.
0002 The IH power supply input voltages are lower than the stipulated voltages
E821 There is a cleaner clogging error.0001 Clogging of toner inside the cleaner has been detected with reference to an
abnormal rise in the cleaner thermistor.- Remove the collecting toner from inside the cleaner.- Replace the air filter of the heat discharge fan.
E824 There is a primary charging cooling fan error.0001 The primary charging cooling fan stop signal has been detected for 5 sec or
more even when the primary charging cooling fan is on.- Check the connection of the connector.- Replace the fan.
E840 There is a shutter error.0001 While the shutter is in operation, the sensor signal is not detected and, in
addition, it is still not detected after 3 retries.- Check the connection of the connector of the shutter motor and the shutter HP sensor.- check the mounting of the pin used to match the shutter gear phase of the fixing unit (See descriptions under "Points to Note When Mounting the Fixing Roller.")- Replace the shutter HP sensor and the shutter motor.
0002 The interval of ON-OFF detection by the sensor in response to shutter operation is shorter than a specific time period.
E841 There is an error in the detection of fixing inlet guide connection.0001 At power-on, the connection of the fixing inlet guide solenoid is not
detected.- Check the connection of the connector.- Replace the solenoid.
Code Description Remedy
Chapter 16
16-16
T-16-3
- XX= '01 to FF'T-16-4
T-16-5
XX YY Description Remedy
00
01
The HDD is not recognized.At start-up, the start-up partition (BOOTDEV) is not found.
1. Turn off the power, and check the HDD cable for disconnection; then, turn the power back on.2. Turn on the power, and put your ear or finger against the HDD to see if the disk inside it is rotating.3. Replace the HDD.4. Replace the main controller PCB.
02
The system software for the main CPU is absent.
1. Start up in safe mode, and execute full formatting using the SST; then, re-install the system software, and turn off and then on the power.2. Replace the HDD.
03
An interrupt has been detected during writing to BootDevice.
1. Turn off the power, and turn it back on while holding down the 1 and 9 keys. See that the auto write interrupt sector repair routine starts and the control panel goes black.2. See the progress of operation on the display (at the start, the upper left cursor will flash). When the display goes white, turn off and then back on the power.3. Start in safe mode, and execute full formatting using the SST. Then, re-install the system software, and turn off and then back on the power.
04 No incidence.
05 No incidence.
06Error in sub CPU system undetected.
1. Start up in safe mode, and execute full formatting using the SST; then, re-install the system software, and turn off and then on the power.2. Replace the HDD.
07Error in ICC Profile undetected. 1. Start up in safe mode, and execute full formatting using the SST; then, re-install
the system software, and turn off and then on the power.2. Replace the HDD.
XX YY
XX CHK-TYPE Partition Description
At start-up During operation
03 05 00,01,02,04 11,21
13,25 10,12,14,22,23,24
Remedy Remedy01
1
FSTDEV compressed image data (e.g., Box)
*1 *5
*9 *10 *11 *12
02 IMG_MNG file management table, profile
03 FSTCDEV job archiving (chasing)04
2
APL_GEN general data
05 TMP_GEN general data (temporary file)
06 TMP_FAX for fax (temporary file)
07 TMP_PSS for PDL spool (temporary file)
08 3 PDLDEV for PDL spool (e.g., font)
09 4 BOOTDEVfirmware (system, MEAP, key, certificate, PDF dictionary, RUI content, audio dictionary)
*3 *8
10 5 APL_MEAP MEAP application *1 *511 6 APL_SEND address book, filter *2 *5
12 7 APL_KEEP MEAP save data *3 *8
13 8 APL_LOG System log saving capacity *1 *5
FF 0 Notidentified
full check on HDD for faulty sector and recovery *4 *7
YY Description Remedy
*1
03 An ongoing write operation is interrupted (at start-up).
1. Set '0' to CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.2. Type in CHK-TYPE that corresponds to the partition in question, and execute HD-CLEAR; then, turn off and then back on the power.
*2
1. Ask the user to download the address book data using a remote UI.2. Set '0' to CHK-TYPE, and execute HD-CHECK; thereafter, turn off and then on the power.3. Start download mode, and execute full formatting using the SST; thereafter, turn off and then back on the power.
*3
The recovery operation for the boot partition necessarily requires the use of the SST in safe mode.1. Set '0' for CHK-TYPE, and execute HD-CHECK; thereafter, turn off and then back on the power.2. Start download mode, and execute full formatting and re-install the system software; thereafter, turn off and then back on the power.
*41. Set '0' to CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.2. Execute HD-CLEAR by setting '1', '2', '3', and '5' to CHK-type; then, turn off and then back on the power.
Chapter 16
16-17
16.3 Error Code (SEND)
16.3.1 Results of Self-Diagnosis0015-5628
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-6
*5
05 A file system error has occurred.
1. Type in CHK-TYPE corresponding to the partition in question, and execute HD-CLEAR; then, turn off and then back on the power.2. Replace the HDD, and re-install the system software.
*6
The machine does not permit execution of HD-CLEAR in service mode (to prevent loss of partition information such as address book and filter data).1. Ask the user to download the address book data using a remote UI.2. Start download mode from service mode; then, execute full formatting using the SST, and re-install the system software. Thereafter, turn off and then back on the power.
*7
1. Execute HD-CLEAR by setting "1', '2', '3', and '5' to CHK-TYPE; then, turn off and then back on the power.2. Replace the HDD, and re-install the system software.
*8
Recovery operation for the Boot partition necessarily requires the use of the SST in safe mode.1. Start in safe mode, and execute full formatting in the SST, and re-install the system software. Thereafter, turn off and then on the power.2. Replace the HDD, and re-install the system software.
*9
00010204
There is poor contact for the HDD, or there is a system
error.
1. Check the cables and power cord for disconnection.2. Start up in safe mode; then, execute full formatting using the SST, and re-install the system software. Thereafter, turn off and then back on the power.3. Replace the HDD, and re-install the system software.
*10 1121
There is poor connection of the HDD.
1. Check the cable and the power connectors for disconnection.2. Replace the HDD, and re-install the system software.
*11 1325
A write operation has been suspended.
File data as of Box on the HDD may be damaged.1. Set '0' for CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.2. Set '1' for CHK-TYPE, and execute HD-CLEAR. (In the case of APL_SEND or BOOTDEV, reformat using the SST and re-install the system software.)3. Replace the HDD, and re-install the system software.
*12
101214222324
There is a system error or a packet data error.
1. Start up in safe mode; then, execute full formatting using the SST, and re-install the system software. Thereafter, turn off and then back on the power.2. Replace the HDD, and re-install the system software.
Cause RemedyThere is a shortage of TCP/IP resources. Try again later.
While continuous transmission is under way or has ended in FTP or Windows (SMB), a shortage of TCP/IP resources has occurred, not permitting reference.
Wait a while; then, try again.
Set the IP address.The IP address of the machine has yet to be set. In user mode, set the IP address; thereafter, turn off and then on the machine.
The server does not respond. Check the settings.The settings of the selected server are not correct, or the server has not been turned on. Or, there may be a shortage of resources.
Wait a while; then, try again. If browsing is still not permitted, select a different server.
NetWare is in use. Try again later.
NetWare is printing using PSeve or NDSPServer, not permitting browsing. Wait until NetWare finishes printing; then, try again.
The layer in question at the target is too deep to browse.
The number of characters is in excess of the number allowed. The layer in question cannot be specified. Specify a different address.
There is no response.The server is not ready for file transmission. Check the target.
YY Description Remedy
Chapter 16
16-18
The network is cut for file transmission. (An attempt to connect to the target of transmission may have failed, or there is an open circuit in the middle.)
Check the network.
The tree name is not specified for NetWare transmission. Type in the tree name.
An error has occurred for TCP/IP in the course of e-mail or i-fax transmission.
Check the condition of the network cable and the connector.
Check TCP/IP.The machine's TCP/IP is not in operation. In user mode, check the TCP/IP settings (IP address, DHCP, RARP, BOOTP).
The selected server cannot be found. Check the settings.The IP address in question cannot be identified. 1. In user mode, check the DNS settings.
2. On the DNS side, check the DNS data settings.
If the login information for the LDAP server is set to 'use (security authentication)', the host name in question cannot be identified.
In user mode, check the TCP/IP settings (DNS settings).
The selected server cannot be connected. Check the settings.An attempt to connect to the IP address/port in question fails. 1. In user mode, check the TCP/IP settings (gateway address of the IP address settings).
2. In user mode, check the LDAP server settings.3. Check to see that the LDAP server is operating normally.4. If the login information of the LDAP server is set to 'use (security authentication)', check to see if the UDP packet is blocked by a filter.
Check the user name, password, or the settings.If the login information of the LDAP server is set to 'use' or 'use (security authentication)', the user name or the password is wrong.
In user mode, check the LDAP server settings (user name, password).
If the login information of the LDAP server is set to 'use (security authentication)', the domain name is wrong.
In user mode, check the LDAP server settings (domain name).
A timeout condition has occurred, and a search cannot be completed. Check the settings.
The search cannot be completed within the specified period of time. In user mode, increase the length of time before a timeout condition occurs (part of LDAP server settings).
An upper limit for search results has been exceeded. If the desired address is not indicated in the results, change the search conditions.
The number of matches has exceeded the number of results brought up in response to the search.
1. Narrow down the search conditions, and try again.2. Try increasing the upper limit.
The search conditions include a character that cannot be used for the selected server.
The symbol \ is used in the search condition. Remove the symbol \ from the search condition, and try once again.The combination of characters used in the search condition fails to make up a correct search condition.There must be as many "s as there are "sThe symbol * is not included within parentheses.
Check to be sure that the combination of characters is in keeping with the rule; then, try once again.
If LDAP of the server and the character code is version 2 (JIS), there is a character that is not part of the ASCII code (0x20-0x7E).
Remove any character that cannot be used; then, try once gain.
The version setting of the server is wrong, and the search cannot be initiated. Check the settings.
Cause Remedy
Chapter 16
16-19
16.3.2 Error Codes0015-5630
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-7
In user mode, the LDAP server settings (server LDAP version and character code) is set for version 3; however, the LDAP server is operating for version 2.
In user mode, set the LDAP server settings so that the LDAP server version and the character code are both version 2.
Cause Remedy# 001There is a paper or original jam. Remove the jammed paper or original.# 003A communication lasting longer than a specific period of time (64 min) will cause an error state.
1. Decrease the resolution for transmission.2. In the case of reception, ask the source to decrease the resolution or divide the original.
# 005The target does not respond within 35 sec. Check to be sure that the target is ready to communicate; then, try once again.
The target is a non-G3 model. Check the target.# 009There is no paper. Supply paper.The cassette is not fitted properly. Fit the cassette correctly.# 011The original to be transmitted is not placed properly. Start over from the beginning.
# 012The target is out of recording paper, and transmission has failed. Ask the target to supply recording paper.
# 018There is no response to a redial attempt. Check to make sure that the target is ready for communication; then, try once again.
The target is engaged for a different communication, and transmission has failed.
Check to make sure that the target is ready for communication; then, try once again.
The settings do not match the settings of the target, and the transmission has failed.
Check to make sure that the target is ready for communication; then, try once again.
# 022The particulars of the group address selected as the forwarding target may have been deleted, or there is no more than a user box, thus causing the transmission to fail.
Try transmitting once again.
The attempt to transmit to an address registered in the address book has failed because the address has been removed from the address table while in wait for transmission.
Try once again.
# 037There is a shortage of memory, not permitting reception. Remove error files and unnecessary files to increase available memory.
# 080F code is not set on the target. Check the F code of the target, and start over.
# 081The appropriate password is not set on the target. Check the password of the target, and start over.
# 099The transmission has been suspended in the middle. Start over.
# 102There is a mismatch of F code or password. Check the F code and the password of the target, and start over.
# 107
Cause Remedy
Chapter 16
16-20
There is a shortage of memory, not permitting transmission. 1. Decrease the resolution, and try once again.2. Remove unnecessary files to increase available space.
# 701The group ID set when the job was introduced no longer exits. Or, the password has been changed.
Type in the correct group ID or the ID No. (using the keypad); then, start over.
# 702The memory is full, not permitting transmission. 1. Wait a while. Try again until the ongoing transmission of a job ends.
2. Try not to transmit to too many addresses at once; rather, try dividing the address into smaller groups.
# 703The memory image area is full, not permitting further writing. 1. Wait a while. Try transmitting after the ongoing transmission of a job ends.
2. Remove files from the Box; if the operation still fails to return to normal, turn off and then back on the main power.
# 704An error has occurred while an attempt is made to obtain address information from the address book.
Check the settings of the address, and try once again; if the operation is still not normal, try turning off and then back on the main power.
# 705The image data size is in excess of the upper limit imposed on transmission data size set in user mode, thus causing suspension of transmission.
Try changing the upper limit imposed on transmission data size as part of the communication control settings of system control settings (user mode). When selecting low resolution mode or using i-fax, try decreasing the number of images to send at one time so that the transmission will not be in excess of the upper limit imposed on transfer data size.
# 706An address table is being imported from or to the remote UI; or, a different transmission component is being used.
Start over once again.
# 711All memory of the Box is used. Delete files from the Box.# 712The Box is full of files. Remove file from the Box.# 713The file has been removed from the Box before transmitting the URL. Put the file in question back into the Box, and start over.
# 751The server is yet to start up. The network is disconnected. (The connection to the target may have failed, or the connection may have been cut in the middle.)
Check the target. Check the network.
# 752The SMTP server name of the e-main/i-fax in question may be wrong, or the server in question is yet to start up. Or, the appropriate domain name or e-mail address has not been set. Or, the network has been disconnected.
Using the network settings of the system control setup (user mode), check the SMTP server name, domain name, and e-mail address. Check to see that the SMTP server is operating normally. Check the connection of the network.
# 753A TCP/IP error has occurred in the course of e-mail transmission. (e.g., socket, select error)
Check the condition of the network cable and the connector. If the operation does not return to normal, try turning off and then back on the main power of the machine.
# 754
Cause Remedy
Chapter 16
16-21
The server has not been started up for transmission, or the network is disconnected. Or, the target settings are wrong.
Check the server and the network. Check the settings of the target.
# 755The TCP/IP settings are not operating normally, thus not permitting transmission.
In user mode, check the TCP/IP settings.
The appropriate IP address has not been set up. In user mode, check the TCP/IP settings.
When the machine is started up, its IP address is not assigned by means of DHCP, RARP, or BOOTP.
In user mode, check the TCP/IP settings.
# 756In system control setup (user mode), 'use NetWare' is set to 'off' in NetWare settings.
In network settings of system control setup (user mode), set 'use NetWare' to 'on'.
# 801While e-mail is being transmitted or i-fax is transmitted/received, the communication with the SMTP server encountered a timeout error because of a factor associated with the main server.
1. Check to see that SMTP is operating normally.2. Check the condition of the network.
While an SMTP connection is being used, the SMTP server has returned an error.The address setting is not correct.When data is transmitted to the file server, an error has occurred owing to a factor associated with the server.
1. Check to see if SMTP is operating normally.2. Check the condition of the network.3. Check the address setting.4. Check the condition of the file server and the setting.
An attempt has been made to transmit data to an address not authorized for a write operation.
Check the address setting.
In the course of transmitting data (file server), it was found that there is a file having the same name, and an overwrite operation to the file is prohibited.
Change the setting of the file server so that overwriting may be permitted.
In relation to transmission (file server), the folder name or the password that has been specified is wrong.
Check the address setting.
# 802In the system control setup (user mode), the settings of the SMTP server for e-mail/i-fax are wrong.The setting of the DNS server is wrong.The attempt to connect to the DNS server has failed.
In the network settings under system control settings (user mode), check the SMTP server name and the DNS server name. Check to see if the DNS server is operating normally.
# 803Before all pages have been transmitted, the target has cut off the network. Try once again.
# 804When an attempt is made to transmit to the file server, it has been found that no match exits in the specified directory.
Check the address.
You are not authorized for access to the folder. Set the server so that you will be authorized to access the folder.
# 806When an attempt to transmit to the file server is made, it has been found that the specified user name or password is wrong.
Change the user name or the password of the address.
The address specified for e-mail/i-fax transmission is wrong. Check the address of the e-mail/i-fax in question.
# 810
Cause Remedy
Chapter 16
16-22
When an attempt is made to receive i-fax, a POP server connection error has occurred.
1. In user mode, check the POP server name setting.2. Check the operation of the POP server.3. Check the condition of the network.
While a connection is made to the POP server, an error has been returned by the POP server.
1. In user mode, check the POP server name setting.2. Check the operation of the POP server.3. Check the condition of the network.
While a connection is made to the POP server, a timeout error has occurred owing to a factor associated with the server.
1. In user mode, check the POP server name setting.2. Check the operation of the POP server.3. Check the condition of the network.
# 815If a file that has been transmitted to the file server is being printed, you will not be able to log in to the server in question.
Wait a while, and then try once again. Or, change the NetWare server settings of the target, or stop PServer.
# 818The data that has been received is in a format that does not permit printing. Ask the source to change the file format and transmit it once again.
# 819The data that has been received is of a type that cannot be handled (i.e., its MIME information is illegal).
Ask the target to check the settings and transmit it once again.
# 820The data that has been received is of a type that cannot be handled (i.e., BASE64 or Unicode is illegal).
Ask the source to check the settings and transmit it once again.
# 821The data that has been received is of a type that cannot be handled (i.e., TIFF interpretation error has occurred).
Ask the target to check the settings and transmit once again.
# 822The data that has been received is of a type that cannot be handled (i.e., the image cannot be decoded).
Ask the source to check the settings and transmit once again.
# 827The data that has been received is of a type that cannot be handed (i.e., part of its MIME information is not supported).
Ask the source to check the settings and transmit once again.
# 828HTML data has been received. Ask the source to use a format other than HTML.# 829The data that is being received consists of 100 pages or more. The machine is designed so that it removes data for the 100th and subsequent pages and
prints or saves in memory up to the 999th page. Ask the source to transmit the remaining pages one again.
# 830A DSN error notice has been received because of the following: the i-fax address or the target settings are wrong, or the data of the file that has been transmitted is greater than the size permitted by the mail server.
1. Check the i-fax address and the target settings.2. In user mode, decrease the upper limit imposed on the size of transmission data so that it is lower than the size permitted by the mail server.3. Check the condition of the mail server, DNS server, and network.
# 831
Cause Remedy
Chapter 16
16-23
An attempt to receive i-fax in SMTP has failed because of the reception/printing range settings made as part of the IP address range setting in user mode.
Change the reception/printing range settings made as part of the IP address range setting in user mode.
# 832In user mode, the e-mail setting or the network setting is yet to be made, causing a mail server fault and, thus, preventing reception of MDN (transmission confirmation) mail.
1. In user mode, check the DNS setting, e-mail/i-fax setting, and IP address made as part of the network settings.2. Check the condition of the mail server and the DNS server.
# 833The network settings have not been made in user mode or there is a mail-server related fault, thus preventing the transmission of the mail (MDN; transmission acknowledgement).
1. In user mode, check the DNS setting, e-mail/i-fax setting, and IP address made as part of the network settings.2. Check the condition of the mail server and the DNS server.
# 834The i-fax address or the condition settings of the target may be wrong, there may be a fault in the network or the mail server, or the target may have encountered a memory full condition, thus causing an MDS error notice.
Check the specified i-fax address and the target conditions.
# 835The number of text lines is more than the maximum number of lines permitted for i-fax.
Ask the target to decrease the number of text lines and try once again.
# 837A request has been made by a host that comes under the restrictions imposed by 'IP address range setting' in user mode.
Check the setting of the IP address range in user mode. The attempt to access in question may be illegal.
# 839The SMTP authentication (SMTPAUTH) user name or password for e-mail/i-fax (network settings) may be wrong.
Check the user name and password used for SMTP authentication (SMTPAUTH) as part of the network settings under system control settings (user mode).
# 841In relation to an attempt for transmission for e-mail/i-fax, there is no coding algorithm that may be used in common with the mail server.
1. Set 'SSL' to 'OFF' as part of the network settings under system control settings (user mode).2. Add a coding algorithm that may be used in common (mail server settings).
# 842In relation to an attempt for transmission of e-mail/i-fax, a request has been made for the use of a client certificate by the mail server.
1. Set 'SSL' to 'OFF' as part of the network settings under the system control settings (user mode).2. Change the mail server settings so that it will not request a client certificate.
# 843The time used by the KDC (key distribution center) server and the time used by the machine are different significantly.
1. Correct the time as part of the date/time settings under the system control settings (user mode).2. Correct the time used by the KDC (key distribution center) server.
# 847
The memory of the Box has been used up, not permitting the storage of the received file in the fax box.
Remove unnecessary files from the fax box or the system box.
# 851The remaining memory of the machine is running short. Check the remaining memory of the machine; then, remove unnecessary files for the
Box.
There are more than 100 files in the specified box, not permitting additional storage.
Remove unnecessary files from the specified box.
# 852
Cause Remedy
Chapter 16
16-24
16.4 Jam Code
16.4.1 Jam Code (machine proper)0015-5640
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-8
T-16-9
16.4.2 Jam Code (finisher-related)0015-5643
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-10
The main power switch has been turned off while a job is being executed, causing an error.
Check to see that the main power switch is on; as necessary, try once again.
# 899The transmission of e-mail or i-fax has ended. However, the transmission has gone through multiple servers, and there is no way of finding out whether the transmission has reached the target.
1. Check with the target to see if the transmission has arrived.2. Check to see if an error notice has arrived.
# 995The reservation for the transmission has been cancelled. As necessary, start over.
Code Jam
01xx delay jam02xx stationary jam
0Axx residual jam
0Bxx cover open jam
Code Sensor Notation
xx01 registration paper sensor PS29xx02 write check sensor PS28xx03 vertical path 1 paper sensor PS24xx04 vertical path 2 paper sensor PS25xx05 vertical path 3 paper sensor PS26xx06 vertical path 4 paper sensor PS27xx07 right deck pull-off sensor PS32xx08 left deck pull-off sensor PS33xx0B right deck retry sensor PS19xx0C left deck retry sensor PS20xx0D cassette 3 retry sensor PS21xx0E cassette 4 delivery sensor PS22xx0F fixing claw jam sensor PS4xx10 inside delivery sensor PS35xx11 outside delivery sensor PS36xx12 delivery jam sensor PS46xx13 reversal sensor 2 PS38xx14 delivery sensor 1 PS37xx15 duplexing paper sensor PS34xx16 duplexing pre-registration sensor PS30xx17 fixing outlet sensor PS52xx18 fixing inlet sensor PS51
Code jam1001 inlet path sensor delay jam1002 punch path sensor feed delay jam1003 escape path sensor feed delay jam1004 delivery path sensor delay jam1101 inlet path sensor stationary jam1102 punch path sensor feed stationary jam1103 escape path sensor feed stationary jam1104 delivery path sensor stationary jam1200 finisher timing jam1300 power-on jam
Cause Remedy
Chapter 16
16-25
16.4.3 Jam Code (ADF-related)0015-5644
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-11
1400 door open jam1500 stapler staple jam
1644 punch jam1645 punch residual jam1791 saddle feed path sensor feed delay jam1792 saddle delivery sensor feed delay jam1793 saddle inlet sensor feed delay jam17A1 saddle feed path sensor feed stationary jam17A2 saddle delivery sensor feed stationary jam17A3 saddle inlet sensor feed stationary jam1786 saddle stapler staple jam1787 saddle power-on jam1788 saddle door open jam17B1 document registration sensor delay jam
17B2 reversing inlet sensor delay jam
17B3 reversing sensor delay jam
17B4 reversing timing sensor delay jam
17B5 deacceleration timing sensor delay jam
17B6 separation timing sensor delay jam
17B7 folding position accuracy sensor delay jam
17B8 upper stopper assembly path sensor delay jam
17B9 delivery 1 sensor delay jam
17BA delivery 2 sensor delay jam
17BB 3-fold tray empty sensor delay jam
17C1 document registration sensor stationary jam
17C2 reversing inlet sensor stationary jam
17C3 reversing sensor stationary jam
17C4 reversing timing sensor stationary jam
17C5 deacceleration timing sensor delay jam
17C6 separation timing sensor stationary jam
17C7 folding position accuracy sensor stationary jam
17C8 upper stopper assembly path sensor stationary jam
17C9 delivery 1 sensor stationary jam
17CA delivery 2 sensor stationary jam
17CB 3-fold tray empty sensor stationary jam
17D1 inserter paper absent jam
17D7 inserter power on jam
17D8 inserter door open jam
Code Sensor Notation Description 0001 post-separation sensor PCB PCB2 The post-separation sensor does not detect paper when paper has been moved 452 mm after the
start of separation.0002 post-separation sensor PCB PCB2 - The separation sensor detects paper when paper has been moved 500 mm (if extra-length, +200
mm) -45.5 mm after registration pickup.- the sensor goes on (paper with hole) before paper has been fed 12 mm after the detection of the trailing edge; the separation sensor detects paper after paper has been fed 50 mm from when the separation senor has gone on.
0003 registration sensor PI1 The registration sensor does not detect paper a feed length of 134.8 mm after the post-separation sensor has gone on.
0004 registration sensor PI1 The read sensor goes off before the registration sensor goes off.0005 read sensor PCB PCB3 - The read sensor does not detect paper a feed length of 364.2 mm (182.1 x 2) from the point of
registration.- The read sensor does not detect paper a feed length of 157.4 mm (78.7 x 2) from the point of No. 2 registration.
Code jam
Chapter 16
16-26
16.5 Alarm Code
16.5.1 Alarm Code0015-5645
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-16-12
0006 read sensor PCB PCB3 - The read sensor detects paper a feed length of 500 mm (if extra-length, +200 mm) after the start of feed, resumed after a temporary stop for reading.- At time of LTRR/LGL identification in mix mode, the read sensor detects paper a feed length of 514 mm after the start of feed from the edging wait point.
0007 delivery reversal sensor PCB PCB4 If not in high-speed duplexing mode, the delivery sensor does not detect paper when paper is moved 132.1 mm after it has reached the leading edge lower stream roller with reference to the activation of the read sensor.
0008 delivery reversal sensor PCB PCB4 The delivery sensor detects paper a feed length of 161.9 mm after the trailing edge read end point.0009 No.2 registration sensor PI12 -When feeding 4 times the distance between the No.1 registration roller and the No.2 registration
sensor after re-pickup from the No.1 registration roller in the simplex pickup from the tray, the No.2 registration sensor does not turn on. (82.2 X 4)mm-When feeding 4 times the distance between the reversal roller + 20 mm and the No.2 registration sensor in the reversal duplexing pickup from the reversal duplexing path, the No.2 registration sensor does not turn on. (22.6 X 4)mm
0010 No.2 registration sensor PI12 The No.2 registration sensor detects papers when feeding the length of 500 X 2 mm after the No.2 registration sensor turned on.
0011 No.2 read sensor PI11 The No.2 read sensor does not turn on when feeding twice the distance between the read position and the No.2 read sensor after the start of reading a document. (47.4 X 2)mm
0012 No.2 read sensor PI11 The read sensor detects papers after feeding the length of 500 mm (+200 mm for the long one) in the detection of the No.2 read sensor
0042 post-separation sensor PCB PCB2 1st sheet, post-separation sensor, stationary0043 registration sensor PI1, PI12 1st sheet, registration sensor, non arrival0044 registration sensor PI1, PI12 1st sheet, registration sensor, stationary0045 read sensor PCB3, PI11 1st sheet, read sensor, non arrival0046 read sensor PCB3, PI11 1st sheet, read sensor, stationary0047 delivery reversal sensor PCB PCB4 1st sheet, delivery sensor, non arrival0048 delivery reversal sensor PCB PCB4 1st sheet, delivery sensor, stationary0049 No.2 registration sensor PI12 1st sheet, No.2 registration sensor, non arrival
0050 No.2 registration sensor PI12 1st sheet, No.2 registration sensor, stationary
0051 No.2 read sensor PI11 1st sheet, No.2 read sensor, non arrival
0052 No.2 read sensor PI11 1st sheet, No.2 read sensor, stationary
0071 TIMING NG - fault in software timing0073 TIMING NG - fault in shift motor0090 ADF open/closed sensor 1 PS502 The ADF has been opened while in operation.0091 ADF open/closed sensor 1 PS502 The ADF has been opened while in operating (paper wait).0092 DF cover open/closed sensor PI6 The cover has been opened while in operation (drive system in operation).0093 DF cover open/closed sensor PI6 The cover has been opened while in operation (paper wait).
Location Description
04 pickup/feed system 0001 right deck lifter error
0002 left deck lifter error0003 3rd cassette lifter error0004 4th cassette lifter error
0008 optional deck lifter error
06 fixing system 0003 fixing web absent
11 drum cleaner system, collecting toner collection system
0001 collecting toner case full
30 high-voltage system 0001 primary charging assembly leakage
0002 transfer charging assembly leakage
0003 separation charging assembly leakage
Code Sensor Notation Description
Chapter 16
16-27
32 potential control system 0001 potential control VD alarm
0002 potential control VL alarm
33 fan system 0001 delivery assembly curl-removing fan alarm
0009 duplexing feed fan alarm
0016 exhaust fan 1 alarm
60 sorter, finisher, shift tray as a whole
0001 shift tray alarm
61 sorter/finisher stapling system 0001 staple absent
62 saddle stitching system 0001 stitch absent
65 sorter/finisher puncher system 0001 punch case full
Location Description
Chapter 17 Service Mode
Contents
Contents
17.1 Outline........................................................................................................................................................................17-117.1.1 Service mode screen configuration .......................................................................................................................................... 17-117.1.2 Entering or selecting service modes ........................................................................................................................................ 17-117.1.3 Exiting service modes .............................................................................................................................................................. 17-217.1.4 Backing Up Service Mode ....................................................................................................................................................... 17-217.1.5 Initial screen............................................................................................................................................................................. 17-217.1.6 Main/intermediate item screen................................................................................................................................................. 17-317.1.7 Sub-item screen........................................................................................................................................................................ 17-3
17.2 DISPLAY (Status Display Mode)..............................................................................................................................17-417.2.1 COPIER ................................................................................................................................................................................... 17-4
17.2.1.1 COPIER List ...............................................................................................................................................................................................17-417.2.2 FEEDER .................................................................................................................................................................................. 17-9
17.2.2.1 FEEDER List ..............................................................................................................................................................................................17-917.3 I/O (I/O Display Mode)............................................................................................................................................17-10
17.3.1 Outline.................................................................................................................................................................................... 17-1017.3.2 R-CON ................................................................................................................................................................................... 17-1117.3.3 FEEDER ................................................................................................................................................................................ 17-1217.3.4 SORTER ................................................................................................................................................................................ 17-1317.3.5 MN-CON ............................................................................................................................................................................... 17-1817.3.6 P-CON.................................................................................................................................................................................... 17-18
17.4 ADJUST (Adjustment Mode) ..................................................................................................................................17-2217.4.1 COPIER ................................................................................................................................................................................. 17-22
17.4.1.1 COPIER List .............................................................................................................................................................................................17-2217.4.2 FEEDER ................................................................................................................................................................................ 17-26
17.4.2.1 FEEDER List ............................................................................................................................................................................................17-2617.4.3 SORTER ................................................................................................................................................................................ 17-26
17.4.3.1 SORTER List ............................................................................................................................................................................................17-2617.5 FUNCTION (Operation/Inspection Mode)..............................................................................................................17-26
17.5.1 COPIER ................................................................................................................................................................................. 17-2617.5.1.1 COPIER List .............................................................................................................................................................................................17-26
17.5.2 FEEDER ................................................................................................................................................................................ 17-3517.5.2.1 FEEDER List ............................................................................................................................................................................................17-35
17.6 OPTION (Machine Settings Mode) .........................................................................................................................17-3617.6.1 COPIER ................................................................................................................................................................................. 17-36
17.6.1.1 COPIER List .............................................................................................................................................................................................17-3617.6.2 FEEDER ................................................................................................................................................................................ 17-58
17.6.2.1 FEEDER List ............................................................................................................................................................................................17-5817.6.3 SORTER ................................................................................................................................................................................ 17-58
17.6.3.1 SORTER List ............................................................................................................................................................................................17-5817.6.4 BOARD.................................................................................................................................................................................. 17-59
17.6.4.1 BOARD List..............................................................................................................................................................................................17-5917.7 TEST (Test Print Mode) ..........................................................................................................................................17-59
17.7.1 COPIER ................................................................................................................................................................................. 17-5917.7.1.1 COPIER List .............................................................................................................................................................................................17-59
17.8 COUNTER (Counter Mode) ....................................................................................................................................17-6017.8.1 COPIER ................................................................................................................................................................................. 17-60
17.8.1.1 COPIER List .............................................................................................................................................................................................17-60
Chapter 17
17-1
17.1 Outline
17.1.1 Service mode screen configuration0015-5495
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
As shown below, the service modes use three screen levels: initial screen -> main/intermediate item screen -> sub-item screen.One set of modes are used for normal maintenance (Level 1 modes), and another set are used for troubleshooting (Level 2 modes).
F-17-1The copier has the 7 service modes listed below.
F-17-2
17.1.2 Entering or selecting service modes0015-5497
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
To execute a copier operation using a service mode, remove the cable from the external controller or the cable from the network before entering the desired mode.Take care when using the FUNCTION (operation/inspection mode) mode, as the copier may malfunction and be damaged if a print job is received from outsidewhile an operation is executing with this mode in effect.
Initial screen(Level 1)
Main/intermediateitem screen(Level 1)
Sub-item screen (Level 1)
Sub-item screen(Level 1)
User screen
Initial screen(Level 2)
Reset key
Previous/next page
( )(2,8)( )
(Select a main item from the top of screen.)(The corresponding intermediate items arethen displayed and can be selected.)
(Select an item.)
Main/intermediateitem screen(Level 2)
Sub-item screen(Level 2)
Sub-item screen(Level 2)
Previous/next page
(Select a main item from the top of screen.)(The corresponding intermediate items are then displayed and can be selected.)
(Select an item.)
( )(2)
COPIER
FEEDER
SORTER
BOARD
DISPLAY
I/O
ADJUST
FUNCTION
OPTION
TEST
COUNTER
Status display mode
I/O display mode
Adjustment mode
Operation/inspection mode
Specifications setting mode
Test print mode
Counter mode
Chapter 17
17-2
1) Press the asterisk key ( ) on the operation panel.2) Press 2 and 8 simultaneously on the numeric keypad.
3) Press the asterisk key ( )on the operation panel.The initial screen (see below) now appears.
F-17-3
17.1.3 Exiting service modes0015-5499
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When the reset key is pressed once, the display returns to the service mode initial screen.When the reset key is pressed twice, the service modes are exited, and the display returns to the user screen (standard screen).
When using the ADJUST, FUNCTION or OPTION service mode, be sure to turn the main power switch ON/OFF after exiting the mode.
17.1.4 Backing Up Service Mode0015-5501
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
All machines are inspected at time of shipment, and adjustment values are recorded on their service labels. If you have replaced the reader controller PCB or theDC controller PCB, or if you have initialized the RAM, ADJUST and OPTION will be reset to their default settings. If you have made adjustments and changedany of the settings, be sure to update the settings recorded on the service label. If specific items are missing on the label, use its blank space.
F-17-4[1] Service label (for main controller PCB/DC controller PCB)[2] Service label (for reader controller PCB)
17.1.5 Initial screen0015-5502
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
COPIER
FEEDER
SORTER
SORTER
ADF service modes Displayed only when the ADF is attached.
Displayed only when the finisher is attached.
BOARDOption board service modes Displayed only when an option board is attached.
Copier service modes
Sorter/finisher service modes
(There are no modes for the sorter, so isn’t displayed even when the sorter is attached.)
[1] [2]
Chapter 17
17-3
F-17-5
17.1.6 Main/intermediate item screen0015-5503
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-17-6
17.1.7 Sub-item screen0015-5504
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
F-17-7
COPIER
FEEDER
SORTER
BOARD
Initial items
Touch an item to select it.
VERSION
USER
ACC-STS
ANALOG
CST-STS
JAM
ERR
Main items
Touch an item to select it.
Intermediate items
Touch an item to select it.
Adjust Function Option Test CounterI/ODisplay
Display
<VERSION> < 1/3 > < READY >
DC-CON
IP
PANEL
ANAPRO
POWER
Selectedintermediateitem
Sub-items
Returns to previous page.
Advances to next page.
Number of pages
Copier status displayReady to receive service/copyoperation.Paper jamExecuting service mode.Performing warmup or similaroperation.Cover openCopyingError
NO-TONER: No tonerWTNR-FUL: Waste toner fullNO-PAPER: No paperALERM: Alarm
READY:
JAM:SERVICE:WAITING:
DOOR:COPYING:ERROR:
Adjust Function Option Test CounterI/O
PREV NEXT +/- OK
Chapter 17
17-4
F-17-8
17.2 DISPLAY (Status Display Mode)
17.2.1 COPIER
17.2.1.1 COPIER List0015-5506
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<VERSION>T-17-1
COPIER > DISPLAY > VERSIONSub-item Description LevelUse it to indicate the ROM version of a particular PCB (copier and accessory).-if <R-CON XX.YY>, XX indicates the version number and the YY, R&D control number.-if no PCB is connected, the indication will be <-,->.
DC-CON indicates the ROM version of the DC controller PCB. 1R-CON indicates the ROM version of the reader controller PCB. 1PANEL indicates the ROM version of the control panel CPU PCB. 1FEEDER indicates the ROM version of the DADF controller PCB. 1SORTER indicates the ROM version of the finisher controller PCB. 1FAX indicates the ROM version of the fax control PCB (for 2-line configuration). 1NIB indicates the version of the network software. 1SDL-STCH indicates the ROM version of the saddle stitcher controller PCB. 1MN-CONT indicates the ROM version of the main controller PCB. 1DIAG-DVC indicates the ROM version of the self-diagnosis device. 1RUI indicates the version of the remote UI. 1PUNCH indicates the version of the punch unit. 1LANG-EN indicates the version of the English language file. 1LANG-FR indicates the version of the French language file. 1LANG-DE indicates the version of the German language file. 1LANG-IT indicates the version of the Italian language file. 1LANG-JP indicates the version of the Japanese language file. 1JAVA-VM indicates the version of JavaVM built into bootable. 1MEAP indicates the version of the MEAP content on the hard disk. 1OCR-CN indicates the version of OCR of the Chinese language file (simplified). 1OCR-JP indicates the version of OCR of the Japanese language file. 1OCR-KR indicates the version of OCR of the Korean language file. 1OCR-TW indicates the version of OCR of the Chinese language file (traditional). 1BOOTROM indicates the version of boot ROM of the main controller PCB.
in "xx.yy_z," "z" indicate the type of boot ROM. 1
TTS-JA indicates the version of the Japanese language audio dictionary. 1TTS-EN indicates the version of the English language audio dictionary. 1WEB-BRWS indicates the version of the web browser. 1
HELP indicates the version of the Simple Navigation. 1
xxxxx ← (yyyyy) {aaaaa to bbbbb}
Toggles value’s sign (±).
key: Stops running operations.
Sets entered value.
Range of values thatcan be enteredValue before change
Stop
key: Clears value.Clear
key: Starts copying without exiting service mode.Start
<ADJ-XY> < 1/3 > < READY >
ADJ-X
Display Adjust Function Option Test CounterI/O
PREV NEXT +/- OK
Pressing an item displaysit in reverse.
ADJ-X Entered value
Chapter 17
17-5
<ACC-STS>T-17-2
FIN-INS indicates the version of the Folding/Inserting unit. 1
WEBDAV indicates the version of the WEBDAV. 1
TIMESTMP indicates the version of the Timestamp. 1
LANG-CS indicates the version of the Czech language file. 2
LANG-DA indicates the version of the Danish language file. 2LANG-EL indicates the version of the Greek language file. 2LANG-ES indicates the version of the Spanish language file. 2LANG-ET indicates the version of the Estonian language file. 2LANG-FI indicates the version of the Finish language file. 2LANG-HU indicates the version of the Hungarian language file. 2LANG-KO indicates the version for the Korean language file. 2LANG-NL indicates the version of the Dutch language file. 2
LANG-NO indicates the version of the Norwegian language file. 2LANG-PL indicates the version of the Polish language file. 2LANG-PT indicates the version of the Portuguese language file. 2LANG-RU indicates the version of the Russian language file. 2LANG-SL indicates the version of the Slovenian language file. 2LANG-SV indicates the version of the Swedish language file. 2LANG-TW indicates the version of the Chinese language file (traditional). 2LANG-ZH indicates the version of the Chinese language file (simplified). 2LANG-BU indicates the version of the Bulgarian language file. 2LANG-CR indicates the version of the Croatian language file. 2LANG-RM indicates the version of the Romanian language file. 2LANG-SK indicates the version of the Slovakian language file. 2LANG-TK indicates the version of the Turkish language file. 2LANG-CA indicates the version of the Catalan language file. 2
COPIER > DISPLAY > ACC-STSSub-item Description LevelFEEDER indicates the connection of an ADF.
0: not connected; 1: connected 1
SORTER indicates the connection of the finisher and puncher unit.sorter type 0: none; 1: finisher; 2: saddle finisher; 3: shift traypunch type 0: none; 1: 2-hole; 2: 2/3-hole; 3: 4-hole (fr); 4: 4-hole (sw) 1
DECK indicates the connection of a paper deck.0: not connected; 1: connected 1
CARD indicates the connection of a card reader.0: card reader connected, but card not inserted1: card reader not connected, or card reader connected and card inserted(with machine ready for copying, [1]; with machine not ready for copying, [0])
1
DATA-CON indicates the connection of a copy data controller.0: not connected; 1: connected 1
RAM indicates the size of the memory mounted on the main controller PCB.1024MB 1
COINROBO indicates the connection of a coin vendor.0: not connected; 1: connected 1
NIB indicates the connection of a network board.0: not connected1: Ethernet board connected2: TokenRing board connected3: Ethernet board and TokenRing board connected
1
PS/PCL indicates the presence/absence of PS/PCL firmware.0: absent; 1: PS/PCL; 2: PS Kanji 1
RIP1 0: no; 1: yes 1NETWARE indicates the presence/absence of NetWare firmware.
0: absent; 1: present 1
COPIER > DISPLAY > VERSIONSub-item Description Level
Chapter 17
17-6
<ANALOG>T-17-3
<CST-STS>T-17-4
<JAM>
PDL-FNC1 b31 : BDL b30 : PS b29 : PCL b28 : PDF b27 : LIPS b26 : N201 b25 : I5577 b24 : ESC/P b23 : HPGL b22 : HPGL2 b21 : IMAGING b20 : KS b19 : BMLinkS b18 to b16 : reserved (for possible addition of PDL)
1
PDL-FNC2 b15 to b0: reserved (for possible addition of PDL) 1HDD indicates the type name of the HDD. 1PCI1/2/3 indicates the board name of PCI1/2/3.
if not connected, indicates [-] (hyphen).if connected, indicates the board name.<Board Name>iSLTO: wireless LAN boardVoice Board: voice guidance board3DES+USB-HOST: security expansion board
1
COPIER > DISPLAY > ANALOGSub-item Description LevelTEMP indicates the machine inside temperature (environment sensor); in deg C 1
HUM indicates the machine inside humidity (environment sensor); in % RH 1
ABS-HUM indicates the moisture content (environment sensor); in g 1FIX-U fixing roller middle temperature (main thermistor, THM1)
indicates the temperature of the middle of the fixing roller.between 0 and 255 deg C, in increments of 1 deg C
1
FIX-UE fixing roller edge temperature (sub thermistor, THM2)indicates the temperature of the edge of the fixing roller.between 0 and 255 deg C, in increments of 1 deg C
1
FIX-SHTR fixing roller end temperature (shutter thermistor, THM3)indicates the temperature of the edge of the fixing roller.between 0 and 255 deg C.
1
CAP-VOL indicates the voltage level of the charger unit [target product: only iR5075]settings range: 0 to 30 (unit: V)The setting for the product not targeted is "---".
1
COPIER > DISPLAY > CST-STSSub-item Description LevelWIDTH-C3 indicates the width of paper in cassette 3 in terms of paper size; in mm. 2WIDTH-C4 indicates the width of paper in cassette 4 in terms of paper size; in mm. 2WIDTH-MF indicates the width of paper in the manual feed tray; in mm. 2
COPIER > DISPLAY > ACC-STSSub-item Description Level
Chapter 17
17-7
F-17-9Touch the appropriate notation for details.[1] To go to the previous page.[2] To go to the next page.[3] To find out the order of jams.[4] To find out the type of jam.[5] To find the sensor in question.[6] To go to the previous Jam screen.[7] To go to the next Jam screen.
<No.> Indicates the order of jams; 1 through 50 (the higher the number, the older the jam).<DATE> indicates the date of occurrence of the jam in question.<TIME1> indicates the time of occurrence of the jam in question.<TIME2> indicates the time of jam recovery.<L> indicates the location of the jam in question; 0 to 2 (0: copier; 1: feeder; 2: finisher).<CODE> indicates the jam code in question.<P> indicates the source of paper.
1: cassette 12: cassette 23: cassette 34: cassette 45: side paper deck6: manual feed tray7: duplexing assembly
<CNTR> indicates the reading of the soft counter used for the source of paper.<SIZE> indicates the size of paper.
<ERR>
F-17-10<No.> indicates how recent the error in question is.1 to 50 (the higher the number, the older the error)
Chapter 17
17-8
<DATE> indicates the date of occurrence of the error in question.<TIME1> indicates the time of occurrence of the error in question.<TIME2> indicates he error recovery time.<CODE> indicates the error code in question.<DTL> indicates the detail code of the error in question. (if none, '0000')<L> indicates the location of the error in question.
0: main controller1: DADF2: finisher3: not used4: reader unit5: printer unit6: PDL board7: fax board
<P> not used
<HV-STS>T-17-5
<CCD>T-17-6
<DPOT>T-17-7
<SENSOR>
COPIER > DISPLAY > HV-STSSub-item Description LevelPRIMARY primary charging current; in uA 1PRE-TR pre-transfer (post) current; in uA 1TR transfer current (1st side); in uA 1SP separation current (1st side); in uA 1BIAS developing bias output value DC component; in V 1SP-N2 separation current (2nd side); in uA 1TR-N2 transfer current (2nd side); in uA 1
COPIER > DISPLAY > CCDSub-item Description LevelTARGET-G indicates the shading target value of green. 2GAIN-OG indicates the gain level adjustment value of green for CCD odd-numbered bits. 2GAIN-EG indicates the gain level adjustment value of green for CCD even-numbered bits. 2GAIN-OR indicates the gain level adjustment value of red for CCD odd-numbered bits. 2
GAIN-ER indicates the gain level adjustment value of red for CCD even-numbered bits. 2
COPIER > DISPLAY > DPOT
Sub-item Description LevelDPOT-K COPIER>FUNCTION>DPC>OFST
potential reflecting the value after execution; in V 1
VL1T light-area potential target value; in V 1VL1M light-area potential measurement value; in V 1VL2M light-area potential measurement value for developing bias; in V 1VDT dark-area potential target value; in V 1VDM dark-area potential measurement value; in V 1VL2M-P light-area potential measurement value for developing bias for printer image; in V 1VL1M-P light-area potential measurement value for printer image; in V 1VL1T-P light-area potential target value for printer image; in V 1VDM-P light-area potential measurement value for printer image; in V 1VDT-P dark-area potential target value for printer image; in V 1LLMT-P laser output limit check for printer: 0: normal; 1: error 2PLMT-P primary charging current limit value setting for printer: 0: normal; 1: error 2LLMT laser power limit value setting: 0: normal; 1: error 2PLMT primary charging current limit value setting for copier: 0: normal; 1: error 2BIAS-P developing bias for printer (result of potential control); in V 2BIAS-C developing bias for copier (result of potential control); in V 2LPOWER-P laser output value for printer (result of potential control) 2LPOWER-C laser output value for copier (result of potential control) 2PRIM-P primary charging current value for printer (result of potential control); in uA 2PRIM-C primary charging current value for copier (result of potential control); in uA 2
Chapter 17
17-9
T-17-8
<MISC>T-17-9
<ALARM-2>
F-17-11<No.> indicates the order of alarm occurrence; between 1 and 50 (the higher the number, the older the alarm)<DATE> date of occurrence of the alarm in question<TIME1> time of occurrence of the alarm in question<TIME2> time of alarm recovery<CODE> code of alarm location and alarm code<DTL> alarm detail code<CNTR> reading of the total counter at time of alarm occurrence
<ENVRNT>- Environment IndicationThe readings of the environment sensor and the fixing thermistor (main) are indicated as a history of changes in the following: machine inside temperature (deg C),humidity (%), fixing roller surface (middle; deg C).
F-17-12T-17-10
Memo:The interval at which data is acquired may be changed using the following service mode item: COPIER>OPTION>BODY>ENVP-IN.
17.2.2 FEEDER
17.2.2.1 FEEDER List0015-5507
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
COPIER > DISPLAY > SENSORSub-item Description LevelDOC-SZ indicates the size of the original identified by the original size sensor. 2
COPIER > DISPLAY > MISCSub-item Description LevelLPOWER indicates the laser intensity (real-time) 2
Item Description
No. order of data acquisition (the higher the number, the older the data)
DATE date of data acquisition
TIME time of data acquisition
D + deg C machine inside temperature
E + % machine inside humidity
F + deg C fixing roller surface (middle) temperature
Chapter 17
17-10
T-17-11
17.3 I/O (I/O Display Mode)
17.3.1 Outline0015-5825
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following provides a guide to the screen appearing in response to the following: COPIER>I/O.
F-17-13
COPIER > FEEDER > DISPLAYSub-item Description LevelFEEDSIZE indicates the size of the original identified by the feeder. 1TRY-WIDE indicates the distance between original width detecting slides (detecting the width of paper; 0.1 mm).
indicates the distance between the slides used to detect the width of originals in the ADF original tray (between 2 points).1
SPSN-LMN post-separation sensor light emission levelindicates the manual adjustment value (light-emission voltage) of the post-separation sensor.optimum range:179 or lower
1
SPSN-RCV post-separation sensor light reception levelindicates the light reception value (of the post-separation sensor after manual adjustment).optimum range:paper present: 154 or lowerpaper absent: 179 or higher
1
RDSN-LMN read sensor light emission levelindicates the manual adjustment value (light emission voltage) of the read sensor.optimum range:179 or lower
1
RDSN-RCV read sensor light reception levelindicates the light reception level of the read sensor after manual adjustment.optimum range:paper present: 154 or lowerpaper absent: 179 or higher
1
DRSN-LMN delivery reversal sensor light emission levelindicates the manual adjustment value (light emission voltage) of the delivery reversal sensor.optimum range:905 or lower
1
DRSN-RCV delivery reversal sensor light reception sensor levelindicates the light reception voltage of the delivery reversal sensor after manual adjustment.optimum range:paper present: 154 or lowerpaper absent: 179 or higher
1
Chapter 17
17-11
F-17-14[A] bit 0[B] bit 15[C] address
17.3.2 R-CON0015-5826
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-12
Address bit Description RemarksP001 0 delivery motor CLK
1 DDIS IF (OPT00-) 0: prohibit operation2 DDIS IF (SPRDY) 0: permit operation3 DDIS IF (OPTI0) 0: active4 ADF pickup motor CLK5 fan power supply ON signal 1: ON6 ADF read motor CLK7 size sensor ON 1: ON
P002 0 shift motor CLK1 24V power monitor 0: normal
2-3 not used4 scanner motor CLK5 13V power supply monitor 0: normal6 Canon Electronics switchover 0: Canon Electronics7 DDIS IF (SCPRDY) 0: permit operation
P003 0 DDIS serial communication (TxD)1 ADF serial communication (TxD)2 DDIS serial communication (RxD)3 ADF serial communication (RxD)4 LED control 1: ON5 ADF serial communication (SCK)
6-7 not usedP004 0 original size detection 0 0: original present
1 original size detection 1 0: original present2 original size detection 2 0: original present3 original size detection 3 0: original present4 DF connection detection5 DDIS IF (SRTS) 0: permit reception6 scanner motor Vref output7 not used
P005 0 PC connection IF (TxD)1 PC connection IF (RxD)2 fan lock detection signal 0: enable3 DDIS IF (SCTS) 0: permit reception
4-7 not used
Chapter 17
17-12
17.3.3 FEEDER0015-5829
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-13
P006 0 not used1 PCB check terminal 1: normal2 DDIS IF (OPTI1) 0: active3 DDIS IF (OPTO1) 0: active4 ADF sensor interrupt input 0: active5 platen cover open/closed sensor interrupt input 0 1: cover open6 HP sensor interrupt input 1: HP7 not used
P007 0 address bus 161 address bus 172 address bus 18
3-4 not used5 ADF pickup motor clock interrupt input6 ADF read motor clock interrupt input7 ADF reversal motor clock interrupt input
P008 0 lamp ON signal 1: ON1 CCD drive ON signal 1: ON2 wait signal 0: wait3 L light signal 0: active4 H light signal 0: active5 read signal 0: active6 ADF serial communication (LOAD) 0: enable7 CPU click output
P009 0 not used1 shading RAM chip select 0: select2 work RAM chip select 0: select3 ASIC register chip select 0: select4 ROM chip select 0: select
5-7 not used
Address bit Description RemarksP001 0 read sensor 0: paper present
1 registration sensor 1: paper present2 delivery reversal sensor 0: paper present3 ADF cover open/closed sensor 0: ADF open
4-7 not usedP002 0 delivery motor current setting 1
1 deliver motor current setting 22 release motor current setting 13 release motor current setting 24 stamp solenoid drive 1: ON5 clutch drive 1: ON6 original detection LED 1: ON7 fan motor drive 1: ON
P003 0 pickup motor current setting CUT1 feed motor current setting CUT2 engagement motor current setting3 feed motor mode setting4 feed motor current setting 15 feed motor current setting 26 pickup motor current setting 17 pickup motor current setting 2
P004 0 ADF cover open/closed sensor 0: ADF cover open1-6 not used7 stamp present/absent 0: stamp present
Address bit Description Remarks
Chapter 17
17-13
17.3.4 SORTER0015-5831
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-14
P005 0 not used1 release HP sensor 1: released2 delivery reversal sensor 0: paper present3 post-separation sensor 0: paper present4 LGL sensor 1: paper present5 AB/Inch check sensor 1: AB6 not used7 original placement sensor 0: paper present
P006 0-7 for R&DP007 0-7 for R&DP008 0-7 for R&DP009 0-7 for R&DP010 0-7 for R&D
Address bit Description Remarks
P001
0 inlet feed motor phase A signal1 inlet feed motor phase B signal2 inlet feed motor phase A* signal3 inlet feed motor phase B* signal4 escape feed motor phase A signal5 escape feed motor phase B signal6 escape feed motor phase A* signal7 escape feed motor phase B* signal
P002
0 punch feed motor phase A signal1 punch feed motor phase B signal2 punch feed motor phase A* signal3 punch feed motor phase B* signal4 tray motor CLK signal5 swing locking motor current switchover I0 0: ON6 swing locking motor phase A signal7 swing locking motor phase B signal
P003
0 TxD for external source1 TxD for write2 RxD for external3 RxD for write4 punch connection detection 0: connected5 OUT for punch communication 0: ON
6-7 not used
P004
0 escape feed motor CLK (IRQ0*)1 not used2 saddle connection detection 0: connected3 upper tray FG (IRQ3*)4 swing lock HP sensor 1: HP5 not used6 front cover open/closed sensor 0: open7 not used
P005
0 TxD for punch communication1 RxD punch for punch communication2 IN for punch communication (IRQ2*) 0: ON
3-7 not used
P006
1 lower tray motor LOCK 0: locked2 not used3 lower tray motor ON 0: ON4 not used5 motor standby signal 0: ON6 not used7 not used
P007 0-7 not used
Address bit Description Remarks
Chapter 17
17-14
P008
0 lower tray area sensor 1 0: detected1 lower tray area sensor 2 0: detected2 lower tray area sensor 3 0: detected3 not used4 punch feed motor CLK (IRQ4*)5 lower tray FG (IRQ5*)6 inlet feed motor lock input (IRQ6*)7 stack edging motor clock input (IRQ7*)
P009
0 inlet sensor 1: paper present1 lower tray paper surface sensor 0: paper present2 1700-sheet paper surface sensor 0: paper present3 upper tray interlock 1: error4 upper tray area sensor 1 0: detected5 upper tray area sensor 2 0: detected6 upper tray area sensor 3 0: detected7 not used
P010
0 inlet feed motor current switch I1 0: ON1 inlet feed motor current switch I0 0: ON2 punch feed motor current switch I1 0: ON3 punch feed motor current switch I0 0: ON4 punch feed motor standby 0: ON5 escape feed motor I0 0: ON6 escape feed motor I1 0: ON7 escape feed motor standby 0: ON
P011
0 upper tray motor CW/CCW 1: CCW/0: CW1 upper tray motor ON 0: ON2 upper tray motor LOCK 0: locked3 solenoid ON signal 0: ON
4-5 not used6 lower tray motor CW/CCW 1: CCW/0: CW7 delivery path sensor 1: paper present
P012
0 inlet roller shift solenoid 1: ON1 buffer roller shift solenoid 1: ON2 expansion IO chip select signal (CS2*)3 IPC chip select (CS3*)
4-7 not used
P013
0 gear change motor phase A signal1 gear change motor phase B signal2 gear change motor current switch I0 0: ON3 gear change motor current switch I1 0: ON4 escape flapper solenoid ON signal 1: ON5 EEPROM output signal6 EEPROM enable signal7 EEPROMCLK
P014
0 EEPROM input signal1 aligning plate FHP sensor 1: HP2 aligning plate RHP sensor 1: HP3 handling tray paper sensor 1: paper present4 trailing edge assist HP sensor 1: HP5 for machine download
6-7 not used
P015
0 aligning plate R motor phase A signal1 aligning plate R motor phase B signal2 aligning pate R motor current switch I0 0: ON
3-7 not used
P016
0 aligning plate F motor phase A signal1 aligning plate F motor phase B signal2 aligning plate F motor current switch I0 0: ON
3-7 not used
P017
0 trailing edge assist motor phase A signal1 trailing edge assist motor phase B signal2 trailing edge assist motor current switch I0 0: ON3 trailing edge assist motor current switch I1 0: ON4 trailing edge assist motor standby signal 0: ON
5-7 not used
Address bit Description Remarks
Chapter 17
17-15
P018
0 stapler shift motor standby signal 0: ON1 stapler motor direction switch CCW 1: ON2 stapler motor direction switch CW 1: ON3 not used4 stapler shift motor phase A signal5 stapler shift motor phase B signal
6-7 not used
P019
0 escape tray path sensor 1: paper present1 escape tray full sensor 1: full2 stapler HP detection 1: HP3 stapler READY 1: ready4 stapler LS 1: staple present5 escape feed upper cover sensor 1: close6 stapler shift HP sensor 1: HP7 stapler alignment interference sensor 1: interference
P020
0 stapler shift motor current switch I0 0: ON1 stapler shift motor current switch I1 0: ON2 No. 1 delivery motor shift solenoid 1: ON3 buffer trailing edge retaining solenoid 1: ON4 stack edging lower roller clutch 1: ON5 shutter open/close clutch 1: ON6 stack edging motor current switch I1 0: ON7 stack edging motor current switch I0 0: ON
P021
0 stack feeding motor phase A signal1 stack edging motor phase B signal2 stack feeding motor phase A* signal3 stack edging motor phase B* signal4 upper tray paper surface sensor 1: paper present5 stapler interlock 1: open6 shutter HP sensor 1: HP7 swing guide interlock 1: open
P022
0 DIPSW_8 0: ON1 DIPSW_7 0: ON2 DIPSW_6 0: ON3 DIPSW_5 0: ON4 DIPSW_4 0: ON5 DIPSW_3 0: ON6 DIPSW_2 0: ON7 DIPSW_1 0: ON
P023
0 PUSHSW1 0: ON1 PUSHSW2 0: ON2 PUSHSW 0: ON3 upper tray paper sensor 0: paper present4 lower tray paper sensor 0: paper present5 24V detection 0: detected6 front cover interlock 1: open7 fan error detection 0: detected
P024
0 fan ON signal 1: ON1 LED1 0: ON2 LED2 0: ON3 LED3 0: ON4 X4-POWER-ON signal 0: ON
5-7 not used
P025
0 saddle guide motor phase A signal1 saddle guide motor phase B signal2 saddle guide motor current switch I0 0: ON
3 saddle feed motor current switch I0 0: ON4 saddle feed motor phase A signal5 saddle feed motor phase B signal6 saddle feed motor phase A* signal7 saddle feed motor phase B* signal
Address bit Description Remarks
Chapter 17
17-16
P026
0 saddle alignment motor phase A signal1 saddle alignment motor phase B signal2 saddle alignment motor current switch I0 0: ON3 saddle paper positioning motor current switch I0 0: ON4 saddle paper positioning motor phase A signal5 saddle paper position motor phase B signal6 solenoid PWM7 saddle folding motor PWM
P027
0 trimmer PICKUP-TxD1 TxD for write2 trimmer CPU-RxD3 RxD for write4 trimmer OUT 0: ON5 trimmer connection detection 0: detected
6-7 not used
P028
0 saddle front stapling current detection 1: detected1 saddle rear stapling current detection 1: detected2 saddle delivery door connection detection 1: detected
3-5 not used6 saddle stapler unit connection detection 1: detected7 not used
P029
0 saddle rear staple detecting switch 0: detected1 saddle front staple detecting switch 0: detected2 saddle front stapler CCW 0: ON3 stapler feed motor standby 0: ON
4-7 not used
P030
0-1 not used2 saddle folding motor FWD (CW) 1: ON3 saddle folding motor RV (CCW) 1: ON4 saddle folding CLK sensor (IRQ0*)5 saddle butting CLK sensor (IRQ1*)6 saddle rear stapler HP sensor (IRQ2*) 1: HP7 saddle front stapler HP sensor (IRQ3*) 1: HP
P031
0 saddle position HP sensor 0: HP1 saddle guide HP sensor 1: HP2 inlet cover sensor 1: close3 saddle stapler unit sensor 0: detected4 saddle butting HP sensor (IRQ4*) 1: HP5 saddle butting TOP sensor (IRQ5*) 1: butting position6 trimmer IN (IRQ6*) 0: ON7 saddle feed motor CLK (IRQ7*)
P032
0 saddle tray paper sensor 0: paper present1 positioning plate paper sensor 0: paper present2 saddle crescent roller sensor 0: HP3 saddle delivery sensor 0: paper present4 saddle trailing edge sensor 1 1: detected5 saddle trailing edge sensor 2 1: detected6 saddle trailing edge sensor 3 1: detected7 saddle path sensor 1: detected
P033
0 saddle butting motor EN 1: ON1 saddle butting motor FWD (CW) 1: ON2 saddle butting motor RV (CCW) 1: ON3 saddle folding HP sensor 0: HP4 not used5 saddle delivery sensor 0: paper present6 saddle aligning plate HP sensor 0: HP7 not used
P034
0 saddle inlet solenoid 1: ON1 saddle No. 1 flapper solenoid 1: ON2 saddle No. 2 flapper solenoid 1: ON3 saddle pickup solenoid 1: ON
4-6 not used7 saddle inlet sensor 1: detected
Address bit Description Remarks
Chapter 17
17-17
P035
0 saddle rear stapler CW (CW) 0: ON1 saddle rear stapler CCW (CCW) 0: ON2 saddle front stapler CW (CW) 0: ON3 chip select (CS1*)
4-7 not used
P036
0 DIPSW_1 0: ON1 DIPSW_2 0: ON2 DIPSW_3 0: ON3 DIPSW_4 0: ON4 DIPSW_5 0: ON5 DIPSW_6 0: ON6 DIPSW_7 0: ON7 DIPSW_8 0: ON
P037
0 not used1 PUSHSW1 0: ON2 5V detection signal 0: detected3 24V detection signal 0: detected4 for revision control5 for revision control6 for revision control7 for revision control
P038
0 download ON signal 1: ON1 not used4 LED3 0: ON5 LED2 0: ON6 LED1 0: ON7 power-on signal 0: ON
P039
0 DIPSW1 0: ON1 DIPSW2 0: ON2 DIPSW3 0: ON3 not used4 PCH-OUT5 trailing edge sensor 1: ON6 punch encoder lock7 punch HP sensor 0: detected
P040
0 PCH-IN1 RxD2 TxD
3-7 not used
P041
0 EEPROM-IN1 EEPROM-OUT2 EEPROM-CLK3 EEPROM-CS4 horizontal registration HP sensor 1: ON5 horizontal registration motor STB 0: ON6 punch motor CCW 0: ON7 punch motor CW 0: ON
P042
0-3 not used4 DIPSW4 0: ON5 horizontal registration motor CUR 0: ON6 PWM7 not used
P043
0 LED1 0: ON1 horizontal registration motor INA2 horizontal registration motor INB3 LED2 0: ON4 front cover sensor 0: close5 BOOTMODE6 PUSHSW2 0: ON7 PUSHSW1 0: ON
P0440-4 not used5 upper cover sensor 1: open
6-7 not used
P045 ADDRA
not used
P046 ADDRB
not used
Address bit Description Remarks
Chapter 17
17-18
17.3.5 MN-CON0015-5834
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
not used
17.3.6 P-CON0015-5836
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-15
P047 AD0 trailing edge sensorP048 AD1 B5R sensorP049 AD2 A4R sensorP050 AD3 B4 sensorP051 AD6 dust sensorP052 AD7 A3 sensor
Address bit Description RemarksP001 0 manual feed paper sensor signal 0: paper present
1 registration paper sensor signal 1: paper present
2 right deck retry sensor signal 1: paper present
3 cassette 3 paper sensor signal 1: paper present4 vertical path 3 paper sensor signal 1: paper present5 cassette 4 paper sensor signal 1: paper present6 vertical path 4 paper sensor signal 1: paper present7 right deck paper sensor signal 1: paper present8 vertical path 1 paper sensor signal 1: paper present9 left deck paper sensor signal 1: paper present
10 vertical path 2 paper sensor signal 1: paper present11 outside delivery sensor signal 1: paper present12 inside delivery paper sensor signal 0: paper present13 not used14 claw jam sensor signal 0: paper present15 left deck pull-off detection signal 1: paper present
P002 0 cassette 3 retry sensor signal 1: paper present1 cassette 4 retry sensor signal 1: paper present2 left deck retry sensor signal 1: paper present3 reversal sensor 1 signal 1: paper present4 right deck limit sensor 1: paper present5 duplexing pre-registration signal 1: paper present6 duplexing horizontal registration sensor signal 0: paper present7 reversal sensor 2 signal 1: paper present8 write check sensor signal 1: paper present9 developing assembly toner sensor signal 0: toner low
10 hopper toner sensor signal 0: toner low11 duplexing paper sensor signal 1: paper present12 fixing web length detection signal 1: web absent13 fixing output sensor signal 0: paper present14 shutter HP signal 0: HP/set position15 collecting toner feedscrew signal 0: lock
P003 0 developing clutch ON signal 1:ON1 left deck pull-off clutch ON signal 1:ON2 manual feed pickup clutch ON signal 1:ON
3 AKM_EX_CLK_ENABLE signal
4 roller bias ON signal 0:ON5 developing AC bias ON signal 0:ON6 high-voltage high-humidity switchover signal 0:ON7 high-voltage AC ON signal 0:ON
8 charger unit operation mode 1
9 not used
10 charger unit operation mode 2
11 not used
12 high-voltage remote signal 0:ON13 EEPROM select signal 1 1:ON14 EEPROM select signal 2 1:ON15 EEPROM select signal 3 1:ON
Address bit Description Remarks
Chapter 17
17-19
P004 0 cassette 3 size detection signal 01 cassette 3 size detection signal 12 cassette 4 size detection signal 03 cassette 4 size detection signal 1
4 fixing shutter thermistor overheating detection signal 1: overheating
5 fixing sub thermistor overheating detection signal 1: overheating6 fixing main thermistor overheating detection signal 1: overheating
7 accessories power supply fan stop detection signal 1: stop
8 not used
9 HVT cooling fan stop detection signal 1: stop
10 circulation duct fan stop detection signal 1: stop11 hopper toner sensor connection detection signal 0: connected12 developing toner sensor connection detection signal 0: connected13 shutter set detection signal 0:HP14 relay OFF detection signal 1:OFF15 fixing inlet guide solenoid connection detection signal 1: not connected
P005 0 separation fan stop detection signal 1: stop1 primary charging cooling fan stop detection signal 1: stop2 DC power supply fan stop detection signal 1: stop3 heat discharge fan stop detection signal 1: stop4 fixing heater power supply fan stop detection signal 1: stop5 controller fan stop detection signal 1: stop6 duplexing feed fan stop detection signal 1: stop7 curl-removing fan stop detection signal 1: stop8 right deck paper level sensor (upper) signal 1: paper present9 left deck paper level sensor (upper) signal 1: paper present
10 duplexing unit detection signal 0: present11 fixing/feed unit detection signal 0: present12 right deck paper level sensor (lower) signal 1: paper present13 left deck paper level sensor (lower) signal 1: paper present
14 charger unit operation status 1
15 fixing web solenoid connection detection signal 1: not connectedP006 0 fixing motor lock detection signal 1: locked
1-6 not used7 hopper MERR 1: error8 bottle MERR 1: error9 not used
10 bottle motor connection detection signal 0: connected11 shift tray full sensor signal 0: full12 shift tray paper sensor signal 0: paper present13 shift tray HP sensor L signal 1:HP14 shift tray HP sensor R signal 1:HP15 shift tray connector detection signal 0: connected
P007 0-7 not used8 fixing inlet sensor signal 1: paper present9 delivery jam sensor signal 1: jam
10 IH-PID0 0:ON11 IH-PID1 0:ON12 high-voltage separation error signal 0: error13 high-voltage transfer error signal 0: error14 high-voltage primary charging error signal 0: error15 12V monitor signal 0:12V ON
Address bit Description Remarks
Chapter 17
17-20
P008 0 manual feed door open/closed sensor signal 0: line1 right deck paper level sensor signal 1: paper present2 right deck pull-off sensor signal 1: paper present3 left deck paper level sensor signal 1: paper present4 left deck limit sensor signal 1: paper present5 cassette 3 paper level sensor signal 1: paper present6 cassette 4 paper level sensor signal 1: paper present7 not used8 cassette 3 open/closed sensor signal 0: open9 cassette 4 open/closed sensor signal 0: open
10 registration clutch ON signal 0:ON11 right deck open/closed sensor signal 0: open12 left deck open/closed signal 0: open13 lower right door open/closed sensor signal 0: open14 bottle cover sensor signal 0: open15 front door open/closed sensor signal 1: open
P009 0 shift tray connection detection signal 1: not connected1 shift tray motor (CCW) signal 0:ON2 shift tray motor (CW) signal 0:ON3 right deck pickup solenoid ON signal 0:ON4 left deck solenoid ON signal 1:ON5 cassette 3 solenoid ON signal 1:ON6 cassette 4 solenoid ON signal 1:ON7 manual feed holding plate release solenoid ON signal 1:ON8 motor enable signal 1:ENABLE9 reversing flapper 1 solenoid ON signal 1:ON
10 reversing flapper 2 solenoid ON signal 0:ON11 fixing inlet guide solenoid ON signal (return) 1: ON (guide at low)12 fixing inlet guide solenoid ON signal (suction) 1: ON (guide at up)13 fixing web solenoid ON signal 1:ON14 drum heater relay SET signal 1:ON15 drum heater delay RESET signal 1:ON
P010 0 right deck lifter motor ON signal 0:ON1 left deck lifter motor ON signal 0:ON2 primary charging wire cleaning motor (CCW) signal 1:ON3 primary charging wire cleaning motor (CW) signal 1:ON4 pre-transfer charging wire cleaning motor (CCW) signal 1:ON5 pre-transfer charging wire cleaning motor (CW) signal 1:ON6 transfer/separation charging wire cleaning motor (CCW) signal 1:ON7 transfer/separation charging wire cleaning motor (CW) signal 1:ON
P011 0 drum motor ON signal 0:ON1 main motor ON signal 0:ON2 cassette heater ON signal 0:ON
3 not used
4 sensor 5V power supply
5 bottle stirring motor ON signal 0:ON
6 hopper stirring motor 2 ON signal 0: forward/1: reverse
7 circulation duct fan (half-speed) ON signal 1: forward/0: reverse
P012 0 circulation duct fan (half-speed) ON signal 1:ON1 circulation duct fan (full-speed) ON signal 1:ON2 drum heater ON signal 0:ON3 power supply fan ON signal 0:ON
4-5 not used6 cassette 4 lifter motor ON signal 0:ON7 cassette 3 lifter motor ON signal 0:ON
P013 0 separation feed fan (half-speed) ON signal 1:ON1 separation feed fan (full-speed) ON signal 1:ON2 primary charging cooling fan (half-speed) ON signal 1:ON3 primary charging cooling fan (full-speed) ON signal 1:ON
4 HVT cooling fan (half-speed) ON signal 1:ON
5 HVT cooling fan (full-speed) ON signal 1:ON
6 lower fan (half-speed) ON signal 1:ON7 lower fan (full-speed) ON signal 1:ON
Address bit Description Remarks
Chapter 17
17-21
P0140 IH power supply cooling fan (half-speed) ON signal 1:ON
1 IH power supply cooling fan (full-speed) ON signal 1:ON2 controller cooling fan (half-speed) ON signal 1:ON3 controller cooling fan (full-speed) ON signal 1:ON4 not used5 duplexing feed fan (full-speed) ON signal 0:ON
6 curl-removing fan (half-speed) 1:ON
7 curl-removing fan (full-speed) 1:ONP015 0 relay shut OFF signal 1:OFF
1 accessories power supply fan (half-speed) ON signal 1:ON
2 accessories power supply fan (full-speed) ON signal 1:ON
3 counter (total) 1:ON4 not used5 pre-exposure LED ON signal 1:ON6 potential sensor ON signal 1:ON7 12V release signal 1:ON
P016 0 DDI-PPRDY1 DDI-CTS2 DDI-PO03 DDI-PO14 DDI-PO25 DDI-PO36 DDI-PO47 DDI-PO5
P017 0 DDI-CPRDY1 DDI-PRSST2 DDI-RST3 DDI-PI04 not used5 DDI-PI26 DDI-PI37 DDI-PI4
P018 0 jam detection port 1: jam
1 IMGON_FLG
2-7 not used
P019 0 not used1 reversal motor clock signal
2-4 not used5 duplexing left feed motor clock signal6 not used7 delivery motor clock signal
P020 0 registration clutch ON signal1-4 not used5 pre-registration motor clock signal6 not used7 duplexing right feed motor clock signal
P021 0 not used1 DDI-TxD2 not used3 DDI-RxD4 DDI-POWER5 DDI-SCNST
6-7 not usedP022 0-7 not usedP023 0 FIN-RESET
1 FIN-MODE2-7 not used
P024 0-4 not used5 pulse count INT6 DMA-END-INT7 DMA-REQ-INT
Address bit Description Remarks
Chapter 17
17-22
17.4 ADJUST (Adjustment Mode)
17.4.1 COPIER
17.4.1.1 COPIER List0015-5840
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<AE>T-17-16
<ADJ-XY>T-17-17
<CCD>
P025 0 deck open detecting switch signal 0: closed1 deck paper absent sensor signal 1: paper present2 deck lifter upper limit sensor signal 1: upper limit3 deck pickup sensor signal 1: paper present4 deck feed sensor signal 1: paper present5 deck pickup clutch ON signal 1:ON6 not used7 deck paper supply position sensor signal 1:ON
P026 0 deck paper level sensor signal 1: paper present1 deck lifter lower limit detection signal 1: lower limit2 deck set sensor signal 1: connected3 deck open sensor signal 1: closed4 deck ID1 1: connected5 deck ID2 0: connected
6 not used
7 switchover of the large/small deck
P027 0 deck open LED ON signal 1:ON1 deck pickup roller release solenoid drive signal 1:ON2 not used3 deck pickup clutch drive signal 1:ON
4-5 not used6 deck main motor drive signal 1:ON7 deck lifter motor drive signal 1:ON
P028 0 deck lifer lower limit detection signal 1:ON1 deck open solenoid 1:ON2 deck main motor constant current setting 1:ON
3-7 not used
COPIER > ADJUST > AESub-item Description LevelAE-TBL adjustment range: 1 to 9 (default: 5)
- to obtain darker characters, increase the setting.- to obtain lighter characters, decrease the setting.If you have initialized the RAM on the reader controller PCB, enter the value indicated on the service label.
1
COPIER > ADJUST > ADJ-XYSub-item Description LevelUse it to adjust the image read start position.- If you have initialized the RAM on the reader controller PCB or replaced the PCB, enter the value indicated on the service label.- If you have changed the setting of this item, record the new setting on the service label.
ADJ-X Use it to adjust the image read start position (X direction).adjustment range: 1 to 100 (default: 26) 1
ADJ-Y Use it to adjust the image read start position (Y direction).adjustment range: 200 to 500 (default: 352) 1
ADJ-Y-DF Use it to adjust the main scanning position for feeder mode.adjustment range: 100 to 400 (default: 248) 1
STRD_POS Use it to adjust the CCD read position for DF stream reading mode.adjustment range: 1 to 200 (default: 100) 1
ADJ-X-MG Fine adjustment of magnification in sub scanning direction at copyboard readingadjustment range: -50 to 50 (default: 0)(unit: 0.01%) 1
ADJ-Y-DF2 Adjustment of the position on the backside in main scanning direction at simultaneous double-sided readingadjustment range: 21 to 106 (default: 76) 1
Address bit Description Remarks
Chapter 17
17-23
T-17-18
<LASER>T-17-19
<DEVELOP>T-17-20
<DENS>T-17-21
<BLANK>
COPIER > ADJUST > CCDSub-item Description LevelSH-TRGT Use it to enter the white level target value for shading correction.
adjustment range: 1 to 2047 (default: 1136) 1
DFTAR-G Use it to adjust the shading target value for green for DF mode.adjustment range: 1 to 2047 (default: 1189) 1
MTF-M1 Setting value of front/back matching MTF in main scanning direction (front).adjustment range: 20 to 80 (default: 50) 1
MTF-M2 Setting value of front/back matching MTF in main scanning direction (center).adjustment range: 20 to 80 (default: 50) 1
MTF-M3 Setting value of front/back matching MTF in main scanning direction (back).adjustment range: 20 to 80 (default: 50) 1
MTF-S1 Setting value of front/back matching MTF in sub scanning direction.adjustment range: 20 to 80 (default: 50) 1
DFCH2G2 Setting of linearity characteristic data value of No. 2 data (Green) of DF composite chart for CCD.adjustment range: 1 to 2550 (default: 2000) 1
DFCH2G10 Setting of linearity characteristic data value of No. 10 data (Green) of DF composite chart for CCD.adjustment range: 0 to 2550 (default: 0) 1
DFCH-G10 Setting of linearity characteristic data value of No. 10 data (Green) of DF composite chart for CIS.adjustment range: 0 to 2550 (default: 0) 1
DFCH-G2 Setting of linearity characteristic data value of No. 2 data (Green) of DF composite chart for CIS.adjustment range: 1 to 2550 (default: 2000) 1
COPIER > ADJUST > LASERSub-item Description LevelPVE-OFST Use it to adjust the laser write start position.
adjustment range: -300 to 300 1
POWER Use it to adjust the laser power (for non-potential control).adjustment range: 0 to 255 1
COPIER > ADJUST > DEVELOPSub-item Description Level
BIAS Use it to adjust the developing bias (for non-potential control).adjustment range: 0 to 600 (default: 180) 1
HVT-DE Use it to enter an offset value for the high-voltage unit.adjustment range: -100 to 100 (default: 0) 1
D-HV-DE Use it to enter the offset value for the high-voltage D/A output for the DC controller PCB.adjustment range: -50 to 50 (default: 0) 1
TSPLY-ADJ Use it to adjust the toner supply distribution (axial direction) for the developing assembly.adjustment range: 1 to 5 (default: 3) 2
COPIER > ADJUST > DENSSub-item Description LevelDENS-ADJ Use it to adjust the density of images (copier/printer).
Use it to correct the F-value table in the event of fading in a high-density area or fogging in an image.adjustment range: 1 to 9 (default: 5)- to decrease fading, increase the value.- to decrease fogging, decrease the value.If you have initialized the RAM on the DC controller PCB, enter the value indicated on the service label.
1
Chapter 17
17-24
T-17-22
<V-CONT>T-17-23
<HV-PRI>T-17-24
<HV-TR>T-17-25
<HV-SP>
COPIER > ADJUST > BLANKSub-item Description LevelBLANK-T Use it to enter the image leading edge non-image width.
1adjustment range: 1 to 500 (default: 94)If you have initialized the RAM on the DC controller PCB or replaced the PCB, enter the value indicated on the service label.
BLANK-B Use it to enter the image trailing edge non-image width.
1adjustment range: 0 to 2362 (default: 47)If you have initialized the RAM on the DC controller PCB or replaced the PCB, enter the value indicated on the service label.
COPIER > ADJUST > V-CONTSub-item Description LevelEPOTOFST Use it to enter the potential offset value.
adjustment range: 0 to 255 (default: 0) 1
VL-OFST Use it to enter the light-area target potential offset adjustment value.adjustment range: -5 to 5 (default: 0) 1
VD-OFST Use it to enter the dark-area target potential offset adjustment value.adjustment range: -5 to 5 (default: 0) 1
DE-OFS-P Use it to enter the offset value of the back contrast for printer images.adjustment range: -50 to 50 (default: 0) 1
VD-OFS-P Use it to enter the target VD offset value for printer images.adjustment range: -5 to 5 (default: 0) 1
DE-OFST Use it to enter the target D offset value for copier images.adjustment range: -50 to 50 (default: 0) 1
VL-OFS-P Use it to enter the target VL offset value for printer images.adjustment range: -50 to 50 (default: 0) 1
COPIER > ADJUST > HV-PRISub-item Description LevelPRIMARY Use it to enter the current setting of the primary charging assembly.
settings range: 0 to 1400 (default: 771) 1
COPIER > ADJUST > HV-TRSub-item Description LevelTR-N1 Use it to adjust the output level of the 1st side of plain paper for an N/N environment.
adjustment range: 100 to 400 (default: 380) 1
TR-N2 Use it to adjust the output level of the 2nd side for an N/N environment.adjustment range: 100 to 400 (default: 310) 1
PRE-TR Use it to adjust the current level of the pre-transfer charging assembly.adjustment range: -300 to 0 (default: -70) 1
HVT-TR Use it to enter the transfer charging assembly high-voltage offset value for the high-voltage unit.adjustment range: -100 to 100 (default: 0) 1
H-PRE-TR Use it to enter the pre-transfer charging assembly high-voltage offset value for the high-voltage unit.adjustment range: -100 to 100 (default: 0) 1
D-PRE-TR Use it to enter the pre-transfer charging assembly high-voltage offset value for the DC controller PCB.adjustment range: -50 to 50 (default: 0) 1
D-HV-TR Use it to enter the transfer charging assembly high-voltage offset value for the DC controller PCB.adjustment range: -50 to 50 (default: 0) 1
Chapter 17
17-25
T-17-26
<FEED-ADJ>T-17-27
<CST-ADJ>T-17-28
<MISC>
COPIER > ADJUST > HV-SP
Sub-item Description Level
SP-N1 Use it to adjust the output level for the 1st side of plain paper for an N/N environment.adjustment range: -500 to 100 (iR5075 default: -240) (iR5055/5065 default: -175)
1
SP-N2 Use it to adjust the output level for the 2nd side of plain paper for an N/N environment.adjustment range: -500 to 100 (iR5075 default: -120) (iR5055/5065 default: -100)
1
HVT-SP Use it to enter the separation charging assembly high-voltage offset level for the high-voltage unit.adjustment range: -100 to 100 1
D-HV-SP Use it to enter the separation charging assembly high-voltage offset value for the DC controller PCB.adjustment range: -50 to 50 1
COPIER > ADJUST > FEED-ADJSub-item Description Level
REGISTUse it to adjust the leading edge registration.adjustment range: -50 to 50 1
ADJ-REFEUse it to adjust the horizontal registration for duplex mode.adjustment range: -50 to 50 1
RG-MFUse it to adjust the registration for manual pickup.adjustment range: -50 to 50 1
COPIER > ADJUST > CST-ADJSub-item Description LevelC3-STMTR Use it to enter the paper width basic value for cassette 3 (STMTR).
adjustment range: 0 to 255 1
C3-A4R Use it to enter the paper width basic value for cassette 3 (A4R).adjustment range: 0 to 255 1
C4-STMTR Use it to enter the paper width basic value for cassette 4 (STMTR).adjustment range: 0 to 255 1
C4-A4R Use it to enter the paper width basic value for cassette 4 (A4R).adjustment range: 0 to 255 1
MF-A4R Use it to enter the paper width basic value for the manual feed tray (A4R).adjustment range: 0 to 255 1
MF-A6R Use it to enter the paper width basic value for the manual feed tray (A6R).adjustment range: 0 to 255 1
MF-A4 Use it to enter the paper width basic value for the manual feed tray (A4).adjustment range: 0 to 255 1
C3-LVOL Use it to enter the capacity of the cassette 3 (50 sheets).adjustment range: 0 to 255 1
C3-HVOL Use it to enter the capacity of the cassette 3 (275 sheets).adjustment range: 0 to 255 1
C4-LVOL Use it to enter the capacity of the cassette 4 (50 sheets).adjustment range: 0 to 255 1
C4-HVOL Use it to adjust the capacity of the cassette 4 (275 sheets).adjustment range: 0 to 255 1
Chapter 17
17-26
T-17-29
17.4.2 FEEDER
17.4.2.1 FEEDER List0015-5843
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-30
17.4.3 SORTER
17.4.3.1 SORTER List0015-5845
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-31
17.5 FUNCTION (Operation/Inspection Mode)
17.5.1 COPIER
17.5.1.1 COPIER List0015-5971
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<INSTALL>
T-17-32
COPIER > ADJUST > MISCSub-item Description LevelATM Use it to make settings related to the atmospheric pressure of the site of installation.
settings range: 0 to 2 (default: 0)0: 1 to 0.75 atm (up to elevation of 2500 m)1: 0.75 to 0.70 atm (elevation between 2500 and 300 m)2: 0.70 to 0.65 atm (elevation between 300 and 3500 m)
1
COPIER > FEEDER > ADJUSTSub-item Description LevelDOCST Use it to adjust the original image leading edge position.
- a higher setting will delay the timing for the image leading edge.adjustment range: -50 to 50 (unit: 0.1 mm)
1
LA-SPEED Use it to adjust the original feed speed in feeder stream reading mode.- a higher setting will increase the speed (i.e., contracts the image).adjustment range: -30 to 30 (unit: 0.1%) 1
DOCST2 Adjustment of VYSNC timing on the backside of the feeder at simultaneous double-sided reading.adjustment range: -50 to 50 [default: 0] (unit: 0.1mm) 1
LA-SPEED2 Use it to adjust the sub scanning magnification in feeder back stream reading mode for duplex simultaneous reading.(for fine adjustment of HSYNC length)adjustment range: -120 to 120 [temporary] (unit: 0.1%)
1
COPIER > SORTER > ADJUSTSub-item Description LevelPNCH-HLE Use it to adjust the length from the edge of paper to the punch hole.
settings range: -4 to 2 (unit: mm) 1
COPIER > FUNCTION > INSTALLSub-item Description Level
TONER-S Use it to stir the toner inside the developing assembly at time of installation.Procedure 1. Select the item to highlight.2. See that the message "Check the developer" is indicated.At this time, check to see that the developing assembly is correctly mounted.3. Press the OK key to start the operation. The operation will automatically stop after a specific period of time.during operation, time remaining (sec): at the end, if successful, '0'; if error, '0xFFFF'.
1
CARD Use it to set up the card reader.ProcedureEnter the number of a specific card (0 to 2001), and press the OK key. (As many as 100 cards may be used, starting from the number you have entered.)At this time, initialization will take place for card control information (group ID and ID No.).
1
Chapter 17
17-27
<CCD>
T-17-33
E-RDS Use it to specify the use of E-RDS.0: off (do not use; default)1: use RDS (transmit all counter information)
1
RGW-PORT Use it to set the Sales Company server port number used for embedded-RDS.settings range: 1 to 6535 1
COM-TEST Use it to check the connection to the server used for E-RDS.Procedure1) Select the item to highlight, and press the OK key.2) See where a connection has been made. (The result will be indicated as 'OK' or 'NG'.)OK: connection possible; NG: connection not possible
1
COM-LOG Use it to indicate the details of the result of the communication test executed for the server used for E-RDS.Procedure1) Select the item to highlight, and press [show info].log information particulars: year, date, time, error code, error detail (128 characters max.)
1
RGW-ADR Use it to specify the URL of the server used for E-RDS.Procedure1) Select the item to highlight, and press [show information].2) When the URL input screen appears, enter the appropriate URL and press the OK key.(default: https://a01.ugwdevice.net/ugw/agnetif010)
1
STRD-POS Use it to adjust the face (CCD) read position for DADF stream reading mode.settings range: 1 to 200 [default: 100] (unit: 0.1 mm) 1
CNT-DATE Setting of the start date to send counter information to the server.Set the start date to send counter information to the server by the third party advanced function for Embedded-RDS (eRDS).[Remarks] This mode is displayed only when the third party advanced function for eRDS is available.Setting range: YYYY: year, MM: month, HH: hour, MM: minuteFactory setting value: 000000000000 (12 digits: YYYYMMDDHHMM)
1
CNT-INTV Setting of the interval to send counter information to the server.Set the interval to send counter information to the server by the third party advanced function for Embedded-RDS (eRDS).[Remarks] This mode is displayed only when the third party advanced function for eRDS is available.Setting range: 1 to 168 (for a week)Factory setting value: 24
1
COPIER > FUNCTION > CCDSub-item Description LevelCCD-ADJ Use it to execute CCD auto adjustment.
Procedure1) Place about 10 sheets of paper (the whitest of all papers used by the user, other than color print paper) on the platen glass.2) Select <CCD-ADJ> to highlight, and press the OK key.3) See that auto adjustment takes place (about 15 sec). During adjustment, <ACTIVE> will be indicated.4) See that the scanning lamp goes on twice during adjustment. At the end, the screen will show <OK!>.5) See that al items of service mode have been updated (COPIER>ADJUST>CCD). Record the new settings on the service label.
If you have replaced the CCD unit, scanning lamp, inverter PCB, or platen board glass (standard white plate), be sure to execute this mode item.
1
DF-WLVL1/2 Use it to execute ADF white level adjustment (platen board scan/stream reading scan)Procedure1) Place a sheet of paper (of the type most frequently used by the user) on the platen board glass, and execute the following: COPIER>FUNCTION>CCD>DF-WLVL1.The white level for book mode is read (checking the degree of transmission of the glass for book mode).2) Place a sheet of paper often used by the user in the DF, and execute the following: COPIER>FUNCTION>CCD>DF-WLVL2.The white level for DF mode (stream reading) is read (checking the degree of transmission of glass for stream reading; reading both sides of the chart). face: computes DFTAR-R/G/B back: computes DFTAR2-R/G/B
Caution:Be sure to execute both of the foregoing 2 items at the same time.
1
LUT-ADJ start-ups the reading sequence for CCD seam correction data (gray plate scanning) [not operating in this machine] 1
COPIER > FUNCTION > INSTALLSub-item Description Level
Chapter 17
17-28
<LASER>
T-17-34
<DPC>
T-17-35
<CST>
T-17-36
DF-LNR Start of calculation of gain offset for front/back matching from DF composite chart reading data (No. 2 and No. 10) By executing this mode after setting the reading data of No. 2 and No. 10 of DF composite chart to perform matching of difference in front/back density to "ADJUST>CCD>DFCH_XX", linearity characteristics are calculated and a setting value is determined.
1
MTF-CLC Calculate the MTF filter count which is actually set to ASIC based on the MTF value. Calculate the MTF filter count which is actually set to ASIC based on the MTF value specified for each CCD/CIS in COPIER>ADJUST>CCD>MTF-M1 to 3, MTF-S1. 1
LUT-ADJ2 start-ups the reading sequence for CCD seam correction data 2 (DS chart) 2
COPIER > FUNCTION > LASERSub-item Description LevelPOWER Use it to turn on the laser for laser power adjustment.
Procedure1) Select the item to highlight, and press the OK key.2) See that the laser goes on.3) See that the laser goes off in about 30 sec. (To turn it off in the middle, press the Stop key.)
1
COPIER > FUNCTION > DPCSub-item Description LevelDPC Use it to force the execution of potential control.
The machine is designed so that it will not perform potential control at power-on (recovery mode) if the temperature of the fixing assembly is 70 deg C or higher. If you have replaced the photosensitive drum or the laser unit, or if you have changed the drum potential setting, be sure to execute this mode item.Procedure1) Select the item, and type in '1'; then, press the OK key.2) Turn off and then on the main power switch.3) See that the machine executes potential control and stops it automatically.
1
OFST Use it to adjust the offset value of the potential sensor.This mode item is part of the series of procedures you have to perform when you have replaced the potential sensor unit. Be sure never to execute it on its own.Procedure1) Select the item to highlight, and press the OK key.2) See that the machine executes offset adjustment and stops it automatically.
1
COPIER > FUNCTION > CSTSub-item Description LevelC3-STMTRC3-A4RC4-STMTRC4-A4R
Use it to register the paper width basic value of the cassette 3/4.STMTR width: 139.5 mm; A4R width: 210 mmTo make fine adjustments after registering a value, use the following: ADJUST>CST-ADJ>C3-STMTR, C3-A4R, C4-STMTR, C4-A4R.Procedure1) Put STMTR paper in the cassette, and adjust the slide guide plate to the width.2) Select C3-STMTR (C4-STMTR) to highlight, and press the OK key so that the machine executes auto adjustment and register the value.3) Likewise, repeat steps 1) and 2) to register the basic value for A4R.
1
COPIER > FUNCTION > CCDSub-item Description Level
Chapter 17
17-29
<CLEANING>T-17-37
<FIXING>
T-17-38
<PANEL>
T-17-39
MF-A4RMF-A6RMF-A4
Use it to register the paper width basic value for the manual feed tray.A4R width: 210 mm; A6R: 105 mm; A4 width: 297 mmTo make fine adjustments after registering a basic value, use the following: COPIER>ADJUST>CST-ADJ>MF-A4R, MF-A6R, MF-A4.Procedure1) Put A4R paper in the manual feed tray, and adjust the size guide to the width.2) Select MF-A4R to highlight, and press the OK key so that the machine executes auto adjustment and register the value.3) Likewise, repeat steps 1) and 2) for A6R and A4.
1
COPIER > FUNCTION > CLEANINGSub-item Description LevelWIRE-CLN Clean all charging wires 5 times (5 trips) all at the same time.
Procedure1) Select the item to highlight, and press the OK key.2) See that the notation changes to 'ACTIVE', indicating that the charging wires are being cleaned.3) See that the machine stops cleaning automatically. (To stop in the middle, press the OK key.)
1
COPIER > FUNCTION > FIXINGSub-item Description LevelNIP-CHK Use it to generate printouts for automatic measurement of the fixing nip width.
Procedure1) Make about 20 A4 prints.2) Put A4 plain or recycled paper in the manual feed tray.3) Select the item to highlight, and press the OK key.4) See that the paper is picked from the manual feed tray, held in the fixing nip area, and discharged in about 20 sec.5) Check the nip width of the discharged paper: if b is from 4.5 to 6.5 mm, the nip may be considered normal. In the event of a fixing fault or wrinkling and if the difference between the front b and the rear c is appreciable, go to step 6) to make adjustments.6) Tighten the screw found on the side with the narrower nip; then, loosen the other screw to the same degree (so that the nip width is identical between front and rear).
1
COPIER > FUNCTION > PANEL Sub-item Description LevelLCD-CHK Use it to check for missing dots in the LCD.
Procedure1) Select the item, and press the OK key to start. See that the front of the touch panel starts to go on in the following order: white, black, red, green, blue.2) Press the Stop key to end the operation.
1
LED-CHK Use it to check the activation of the LEDs on the control panel.Procedure1) Select the item, an press the OK key to start. See that the LEDs go on in sequence.2) Press [LED-off] to end the operation.
1
LED-OFF Check the LEDs on the control panel.Procedure1) Select the item to end the operation for LED-CHK.
1
KEY-CHK Use it to check the key inputs.Procedure1) Select [KEY-CHK] so that the numbers and names of input keys appear.2) Check a key to check. If normal, its corresponding character will appear on the touch panel. (See the table.)3) Select [KEY-CHK] to end the ongoing check.
1
TOUCHCHK Use it to adjust the coordinates of the analog touch panel.Procedure- Use it to match a specific point of the touch panel and its coordinates on the LCD.- If you have replaced the LCD assembly, be sure to execute this service mode item.1) Select [TOUCH CHECK] to highlight, and press the OK key.2) Press the 9 + symbols that appear on the touch panel to make adjustments.
1
COPIER > FUNCTION > CSTSub-item Description Level
Chapter 17
17-30
Numbers and Names of Input KeysT-17-40
<PART-CHK>T-17-41
T-17-42
- Clutch
T-17-43
- Motor
Key Indication on screen0 to 9,#,* 0 to 9,#,*Reset RESETStop STOPUser mode USERStart STARTClear CLEARID IDHelp ?Counter Check BILL
COPIER > FUNCTION > PART-CHK Sub-item Description LevelCL Use it to select a clutch whose operation you want to check.
(range: 1 to 5)Procedure1) Select the item.2) Using the keypad, type in the code of the clutch.3) Press the OK key.4) Press [CL-on] to check the operation.
1
CL-ON Use it to start a check on the clutch.Procedure1) Select an item, and press the OK key so that the clutch will repeatedly go on and off as follows: for 0.5 sec, on -> for 10 sec, off -> for 0.5 sec, on -> for 10 sec, off -> for 0.5 sec, on -> off.
1
MTR Use it to select the motor whose operation you want to check.(range: 1 to 30)Procedure1) Select the item, and press the OK key so that the motor will repeatedly go on and off as follows: for 0.5 sec, on -> for 10 sec, off -> for 0.5 sec, on -> for 10 sec, off -> for 0.5 sec, on -> off.
1
MTR-ON Use it to start the operation of the motor.Procedure1) Select the item, and press the OK key so that the motor will repeatedly go on and off as follows:- for 20 sec on -> off- the hopper stirring motor and horizontal registration motor: for 10 sec, on -> off- shift tray motor: stops at front/rear HP
Be sure to remove the toner bottle before checking the operation of the bottle motor (MTR=22); otherwise, the toner is likely to spill out inside the machine.
1
SL Use it to select the solenoid whose operation you wan to check.(range: 1 to 11)Procedure1) Select the item.2) Type in the code of the solenoid using the keypad.3) Press the OK key.4) Press [SL-on] to check the operation.
1
SL-ON Use it to start the operation of the solenoid.1) Select the item, and press the OK key so that the solenoid will repeatedly go on and off as follows: for 0.5 sec, on -> for 10 sec, off -> for 0.5 sec, on -> for 10 sec, off -> for 0.5 sec, on -> off. 1
Code Name1 manual feed d pickup clutch (CL3)2 left deck pull-off clutch (CL4)3 side deck pickup clutch (CL102)4 developing clutch (CL1)5 registration roller clutch (CL2)
Code Name1 laser scanner motor (M22)2 drum motor (M1)
Chapter 17
17-31
T-17-44
- Solenoid
<CLEAR>
T-17-45
3 main motor (M2)4 fixing motor (M3)5 right deck pickup motor (M11)6 left deck pickup motor (M24)7 cassette 3/4 pickup motor (M12)8 vertical path duplexing feed motor (M25)9 vertical path lower motor (M27)
10 vertical path upper motor (M26)11 side deck main motor (M101)12 reversal motor (M14)13 duplexing feed right motor (M18)14 delivery motor (M13)15 pre-registration motor (M17)16 duplexing feed left motor (M19)17 primary charging wire cleaning motor (M6)18 pre-transfer charging wire cleaning motor (M7)19 transfer/separation charging wire cleaning motor (M8)
20 hopper stirring motor (M9); CW rotation (feed/stirring)
21 hopper stirring motor (M9); CCW rotation (stirring)22 bottle motor (M10)
be sure to remove the toner bottle before starting a check.
23 duplexing horizontal registration motor (M16)24 shutter motor (M15)25 right deck lifter motor (M4)26 left deck lifter motor (M5)27 cassette 3 lifter motor (M20)28 cassette 4 lifter motor (M21)29 side deck lifter motor (M102)30 shift tray motor (SM101)
Code Name1 right deck pickup solenoid (SL6)2 left deck pickup solenoid (SL7)3 cassette 3 pickup solenoid (SL3)4 cassette 4 pickup solenoid (SL4)5 manual feed release solenoid (SL2)6 deck pickup roller release solenoid (SL101)7 delivery flapper solenoid (SL5)8 reversing flapper solenoid (SL8)9 fixing inlet guide drive solenoid (SL1); plunger returned
10 fixing inlet guide drive solenoid (SL1); plunger drawn11 fixing web solenoid (SL9)
COPIER > FUNCTION > CLEARSub-item Description LevelERR Use it to reset an error code.
(codes: E000, E001, E002, E003, E004, E005)Procedure1) Select the item, and press the OK key.2) Turn off and then on the main power.
1
DC-CON Use it to initialize the RAM on the DC controller PCB.The RAM will be initialized when the main power switch is turned off and then back on.Procedure1) Print out the service mode particulars using the following: COPIER>FUNCTION>MISC-P>P-PRINT.2) Select the item, and press the OK key.3) Turn off and then on the main power switch.4) As necessary, enter the data you have printed using P-PRINT.
1
Code Name
Chapter 17
17-32
R-CON Use it to initialize the RAM on the reader controller PCB.The settings will be initialized when you turn off and then on the main power switch.Procedure1) Print out the service mode particulars using the following: COPIER>FUNCTION>MISC-P>P-PRINT.2) Select the item, and press the OK key.3) Turn off and then back on the main power.4) As necessary, enter the data you have printed using P-PRINT.
1
JAM-HIST Use it to reset the jam history.The jam history will be reset when the OK key is pressed.Procedure1) Select the item, and press the OK key.
1
ERR-HIST Use it to reset the error code history.The error code will be reset when the OK key is pressed.1) Select the item, and press the OK key.
1
PWD-CLR Use it to reset the password of the system administrator.The password of 'system administrator' set in user mode is reset when the OK key is pressed.Procedure1) Select the item, and press the OK key.
1
ADRS-BK Clearing the address book.The address book is cleared when the main power switch is turned OFF and ON. 1
CNT-MCON Use it to reset the service counter whose reading is kept by the main controller PCB.The counter reading is reset when the OK key is pressed.Procedure1) Select the item, and press the OK key.
1
CNT-DCON Use it to reset the service counter whose reading is kept by the DC controller PCB.The counter reading will be reset when the OK key is pressed.Procedure1) Select the item, and press the OK key.
1
OPTION Use it to reset the service mode setting OPTION to its default setting (as upon RAM initialization).The setting will be initialized when the OK key is pressed.The execution of this item will reset the data kept by the main controller, DC controller, and reader controller.Procedure1) Print out the service mode particulars using the following: COPIER>FUTON>MISC-P>P-PRINT.2) Select the item, and press the OK key.
1
MMI Use it to reset the following settings of user mode:- backup user data for copier control panel (user settings)- common settings backup data (user settings)- various backup data except FAX data (sure settings)The settings will be initialized when the main power switch is turned off and then back on.Procedure1) Select the item, and press the OK key.2) Turn off and then back on the main power.
1
MN-CON Use it reset the RAM on the main controller PCB.The RAM will be reset when the main power switch is turned off and then back on.Procedure1) Print out the service mode particulars using the following: COPIER>FUNCTION>MISC-P>P-PRINT.2) Select the item, and press the OK key.3) Turn off and then back on the main power.4) As necessary, enter the data you have printed out using P-PRINT.
1
CARD Use it to reset the data related to card ID (group).The card ID-related data will be reset when the main power switch is turned off and then back on.Procedure1) Select the item, and press the OK key.2) Turn off and then back on the main power.
1
ALARM Use it to reset the alarm log.The alarm log will be reset when the main power switch is turned off and the back on.Procedure1) Select the item, and press the OK key.2) Turn off and then back on the main power.
1
LANG-ERR Clear the language-related error.Use this mode to recover from an error when a language-related error occurs after the language setting is changed from the default. (The setting is returned to the default value after recovery.)
1
DF-RCON Initialize the backup data of DF-RCON board (EEPROM)Clear the EEPROM value used to maintain backup data installed in DF-RCON and initialize the data. 1
SND-STUP Use it to reset the transmission read settings.The transmission read settings will be reset when the main power switch is turned off and then back on.Procedure1) Select the item, and press the OK key.2) Turn off and then back on the main power.
2
COPIER > FUNCTION > CLEARSub-item Description Level
Chapter 17
17-33
<MISC-R>
T-17-46
<MISC-P>
T-17-47
CA-KEY Use it to reset the CA certificate and key.The CA certificate and the key will be reset when the main power switch is turned off and then back on.Procedure1) Select the item, and press the OK key.2) Turn off and then back on the main power.
2
KEY-CLR Clear the encryption key for the HDD encryption board.Clear the key to replace the encryption key in the HDD encryption board (security kit).Select KEY-CLR and press the OK key to clear the encryption key.When turning off/on the main power after performing this operation, the encryption board installation process operates, and a new encryption key is generated.Note) When this operation is performed, all the data in HDD become unavailable. Therefore, when turning off/on the main power after performing this operation, it is necessary to start from formatting of HDD.
2
COPIER > FUNCTION > MISC-RSub-item Description LevelSCANLAMP Use it to turn on the scanning lamp.
Procedure1) Select the item.2) Press the OK key so that the scanning lamp goes on and remains on for 3 sec.
1
COPIER > FUNCTION > MISC-PSub-item Description LevelP-PRINT Use it to print out service mode settings.
Procedure1) Select the item.2) Press the OK key to generate a printout.
1
USER-PRT Use it to print out user mode settings.Procedure1) Select the item.2) Press the OK key to generate a printout.
1
PRE-EXP Checking the pre-exposure lamp (LED).1) Select the item to highlight.2) Press the OK key to execute various operations for several seconds. The operation will stop automatically. (full activation)3) Press the OK key to generate a printout.ReferenceIf the photosensitive drum suffers a fault as the result of lamp activation, rotate the drum.
1
D-PRINT Use it to print out service mode settings (DISPLAY).The settings under DISPLAY will be printed (not including P-PRINT, LBL-PRINT, HIST-PRINT and ALARM).Procedure1) Select the item.2) Press the OK key to generate a printout.
1
ENV-PRT Use it to print out a log of changes in the machine inside temperature/humidity and in fixing temperature.The log will show changes in the machine inside temperature/humidity and in fixing temperature (center) collected from the monitor outputs of the non-contact thermistor and the environment sensor.1) Select the item.2) Press the OK key to generate a printout.
1
KEY-HIST Use it to print out the history of control panel key inputs.1) Select the item.2) Press the OK key to generate a printout.
1
TRS-DATA Transition of memory reception data.Transmit the memory reception data to the data BOX. Operation Method: 1) Select the item. 2) Press [OK] so that the data is transmitted.
1
COPIER > FUNCTION > CLEARSub-item Description Level
Chapter 17
17-34
<SENS-ADJ>
T-17-48
<SYSTEM>
T-17-49
LBL-PRNT Print the service label. Print the description on the service label. Operation Method: 1) Set an A4/LTR in Cassette 1. 2) Select the item. 3) Press [OK] so that the label is printed. It will take about 15 sec to start printing.
1
HIST-PRT Use it to print out the jam history and the error history.Procedure1) Select the item.2) Press the OK key to generate a printout.
2
COPIER > FUNCTION > SENS-ADJSub-item Description LevelSTCK-LMT Use it to adjust the position of the shift tray full sensor.
If the tray is full, 'on' will be indicated; if empty, 'off' will be indicated. 2
COPIER > FUNCTION > SYSTEMSub-item Description LevelDOWNLOAD Use it to switch to download mode.
Procedure 1) Select the item.2) Press the OK key to start download mode.
1
CHK-TYPE Use it to select the appropriate partition number for execution of HD-CHECK or HD-CLEAR.Procedure1) Select the item.2) Select the number of the partition you want using the keypad.0: entire HDD (*1, *2)1: image storage area2: general-purpose file (user settings data, log data, PDL spool data) storage area3: PDL-related file storage area4: firmware storage area (*1, *2)5: MEAP area6: address book area (*1)
*1: cannot be initialized using HD-CLEAR.*2: can be initialized using the SST.
1
HD-CHECK Use it to check and recover the partition you have selected using CHK-TYPE.procedure1) Select the item.2) Press the OK key.3) See the result. (1: OK; 2: NG (hardware); 3: NG (software) (recovery sector/substitute sector also indicated))
1
HD-CLEAR Use it to initialize the partition you have selected using CHK-TYPE.Procedure1) Select the item.2) Press the OK key.
1
DEBUG-1 Specify the type of logs to be saved and the timing to save them in HDD.Setting value: 0 to 3 (Default: 0)MEMO:-This mode is not used in regular service. (This mode is used to analyze causes of troubles.)-Follow an instruction of Quality Support Div. when using this mode.
Setting range:0: Save PLOG at the timing when Reboot/Exception is detected.1: Save PLOG at the timing when Reboot/Exception/Ecode is detected.2: Save SUBLOG at the timing when Reboot/Exception/Ecode is detected.3: Save SUBLOG in overwriting mode at the timing when Reboot/Exception/Ecode is detected.Factory setting value: 0
2
DEBUG-2 Print out logs saved in HDD.Print out PLOG data which is saved when "0" or "1" is specified for COPIER>FUNCTION>SYSTEM>DEBUG-1.[Remarks] SUBLOG data saved when "2" or "3" is specified for COPIER>FUNCTION>SYSTEM>DEBUG-1 is not printed out.
Number of printouts: Approximately 20 printouts in A4 size
2
COPIER > FUNCTION > MISC-PSub-item Description Level
Chapter 17
17-35
17.5.2 FEEDER
17.5.2.1 FEEDER List0015-5973
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-50
COPIER > FEEDER > FUNCTION Sub-item Description LevelSENS-INT Use it to adjust the sensitivity of individual sensors of the ADF.
Be sure to clean the sensor area before executing the item.Procedure1) Select the item, and press the OK key.2) See that the execution ends automatically.
1
MTR-CHK Use it to check the ADF motor on its own.Procedure1) Press MTR-CHK to highlight.2) Type in the appropriate motor number using the keypad.3) Press the OK key.4) Press MTR-on to start the check.Motor Number0: pickup motor1: feed motorAdjustment range: 0 to 4
1
TRY-A4 Use it to execute automatic adjustment of paper width detection reference point 1 of the ADF original pickup tray. (A4) 1
TRY-A5R Use it to execute automatic adjustment of paper width detection reference point 2 of the ADF original pickup tray. (A5R)1
TRY-LTR Use it to execute automatic adjustment of paper width detection reference point 1 of the ADF original pickup tray. (LTR) 1
TRY-LTRR Use it to execute automatic adjustment of paper width detection reference point 2 of the ADF original pickup tray. (LTRR) 1
FEED-CHK Use it to check paper movement in the ADF on its own.Procedure1) Press FEED-CHK to highlight.2) Type in the appropriate paper feed mode using the keypad.3) Press the OK key.4) Press FEED-on to check the operation.Paper Feed Mode Number0: simplex pickup delivery operation1: duplex pickup delivery operation2: simplex pickup delivery operation (w/ stamp)3: duplex pickup delivery operation (w/ stamp)
1
CL-CHK Use it to check the ADF clutch on its own.Procedure1) Press CL-CHK to highlight.2) Type in the appropriate clutch number.3) Press the OK key.4) Press CL-on to check the operation.Clutch Number0: pickup clutch
1
CL-ON Use it to start the operation of the clutch.Procedure1) Press CL-on and then the OK key to start the operation of the clutch.2) Press the OK key once again to stop the operation. (The operation will stop automatically in about 2 sec; however, the indication will not change to 'STOP' unless you press the OK key.)
1
FAN-CHK Use it to check the ADF cooling fan on its own.Procedure1) Press FAN-CHK to highlight.2) Type in the fan number using the keypad.3) Press the OK key.4) Press FAN -on to check the operation.Fan Number0, 1: cooling fanAdjustment range: 0 to 2
1
FAN-ON Use it to start fan operation.Procedure1) Press FN-on and then the OK key to start the operation of the fan.2) Press the OK key to stop the operation.(The fan will stop automatically in about 5 sec; however, the indication will not be 'STOP' unless the OK key is pressed.)
1
Chapter 17
17-36
17.6 OPTION (Machine Settings Mode)
17.6.1 COPIER
17.6.1.1 COPIER List0015-6258
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<BODY>
T-17-51
SL-CHK Use it to check the ADF solenoid on its own.Procedure1) Press SL-CHK to highlight.2) Type in the solenoid number using the keypad.3) Press the OK key.4) Press SL-on to check the operation.Solenoid Number0: locking solenoid1: stamp solenoid
1
SL-ON Use it to start the operation of the solenoid.Procedure1) Press SL to highlight and then the OK key to start the operation of the motor.2) Press the OK key once again to stop the operation.(The operation will stop automatically in about 5 sec; however, the indication will not be 'STOP' unless the OK key is pressed once again.)
1
MTR-ON Use it to start the operation of the motor.Procedure1) Press MTR-on to highlight and then the OK key to start the operation of the motor.2) Press the OK key once again to stop the operation.(The operation will stop automatically in about 5 sec; however, the indication will not be 'STOP' unless the OK key is pressed.)
1
ROLL-CLN ADF Roller Cleaning ModeExecute the mode so that the motor will rotate the roller. Force lint-free paper moistened with alcohol against the roller to clean it.Procedure1) Press ROLL-CLN to highlight.2) While the roller is rotating, force lint-free paper moistened with alcohol against the roller to clean.3) Select ROLL-CLN to highlight and press the OK key so that the roller will stop.
1
FEED-ON Use it to check the movement of paper in the ADF on its own.Procedure1) Press FEED-on and then the OK key so that paper movement will start according to the operation mode selected using FEED-CHK.
1
COPIER > OPTION > BODYSub-item Description LevelPO-CNT Use it to turn on and off the potential control mechanisms.
setting: 0: off; 1: on (default)1
MODEL-SZ Use it to switchover the default magnification ratios and ADF original size detection.0: AB (6R5E)1: inch (5R4E)2: A (3R3E)3: AB/inch (6R5E)
1
FIX-TEMP Use it to select down sequence mode.0: normal1: standard + 10 deg C (default)2: standard - 5 deg C 1
FUZZY Use it to turn on and off fuzzy control and to set the environment.0: enable fuzzy control (default)1: fix to low humidity environment mode (current level lower than standard)2: fix to normal temperature/humidity mode3: fix to high humidity mode (current level higher than standard)
1
COPIER > FEEDER > FUNCTION Sub-item Description Level
Chapter 17
17-37
CONFIG Use it to select multiple firmware items stored on the hard disk and switchover country, language, machine type, and paper size configuration.ProcedureXXYYZZXX: country (JP); YY: language (ja); ZZ (00): machine type; AA (00): paper size configuration. The indications will be in keeping with the following: COPIER>DISPLAY>USER>LANGUAGE.(The notations in parentheses indicate defaults. The country and language notations are for indication only.)1) Select <CONFIG>.2) Select the appropriate item to highlight, and press the +/- key.3) See that each press on the +/- key changes the selections in sequence.4) When you have made all selections, press the OK key.5) Turn off and then on the main power switch.
1
TR_SP_C1 Use it to change the transfer/separation output settings when the right deck is used as the source of paper by way of providing a remedial measure.Setting0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_C2 Use it to change the transfer/separation output setting when the left deck is used as the source of paper by way of providing a remedial measure.Settings0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_C3 Use it to change the transfer/separation output setting when the cassette 3 is used as the source of paper by way of providing a remedial measure.Settings0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_C4 Use it to change the transfer/separation output setting when the cassette 4 is used as the source of paper by way of providing a remedial measure.Settings0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_MF Use it to change the transfer/separation output setting when the manual feed tray is used as the source of paper by way of providing a remedial measure.Settings0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault 1
TR_SP_DK Use it to change the transfer/separation output setting when the side paper deck is used as the source of paper by way of providing a remedial measure.Settings0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault 1
W/SCNR Use it to indicate the presence/absence of a reader unit.0: reader unit absent (printer model)1: reader unit present (default)When the presence of a reader unit is detected, the machine will automatically set it to '1'.
1
DFDST-L1 Use it to adjust the dust detection level for the ADF (sheet-to-sheet correction).A higher setting will cause the machine to be more sensitive to finer particles of dust.setting: 0 to 225(Setting the item to '0' will disable the dust detection mechanism.) 1
DFDST-L2 Use it to adjust the dust detection level for the ADF (post-job detection).A higher setting will cause the machine to detect finer particles of dust.setting: 0 to 255(Setting the item to '0' will disable the dust detection mechanism.) 1
ENVP-INT Use it to set the interval at which a log is collected for the machine inside temperature/humidity and fixing temperature.COPIER>FUNCTION>MIS-P>ENV-PRT andCOPIER>DISPLAY>ENVRNTsetting0 to 480 (default: 60; in min)
1
BASE-SW Use it to switch from MEAP-full model to base model.setting0: off (base model)1: on (full model) 1
SC-L-CNT Use it to change the threshold level of the paper size (large/small) for the scan counter.setting0: count B4 as small size (default)1: count B4 as large size
1
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-38
DHON-TM Use it to set the timing at which drum heater goes on in sleep mode (with reference to clock time).setting: 0 to 24 (default: 0: in hr)
1
DHON-IVL Use it to set the timing at which the drum heater goes on in sleep mode (with reference to time after a shift to sleep mode).setting: 0, 15 to 1440 (default: 0; in min)
1
DHOF-TM Use it to set the timing at which the drum heater goes off in sleep mode (with reference to clock time).setting: 0 to 24 (default: 01; in hr)
1
DHOF-IVL Use it to set the timing at which the drum heater goes off in sleep mode (with reference to time after a shift to sleep mode).setting: 0, 15 to 1440 (default: 0; in min)
1
CBLTINVL Use it to change the number of times the fixing web solenoid goes on.Make use of it when image faults occur as the result of soiling on the pressure roller.Setting0: normal (default)1: twice normal
1
CCD-LUT Usage setting for the CCD gain correction data Use this item to correct the image deterioration (difference in density at center seam of image) due to aging. Set enabling/disabling data usage corrected with one of the followings: COPIER > FUNCTION > CCD > LUT-ADJ, or LUT-ADJ2. Setting value: 0: not use [default] 1: use (LUT-ADJ correction data) [not available with this machine] 2: use (LUT-ADJ2 correction data)
1
ABC-MODE Switching the background processing of document (switching digital ABC setting) Setting value: -1: not switch the background density (setting for photo document and document with complex modeling) 0: default 1 to 3: bigger the value is set, lighter the background density is.
1
SJOB-CL Set whether or not to permit cancellation of the scanning job when a user performs logout.Cancel the operating scanning job when a user performs logout.[Remarks]- "Scanning job" means a job for which scanning operation is completed, and the operation cannot be canceled when the scanning operation is being executed.- Cancellation performed by this mode is saved in the log in the same manner as cancellation performed by a user.
Setting range:0: Cancellation prohibited1: Cancellation permittedFactory setting value: 0
1
IFX-CHIG Set the number of characters to ignore the email message received by IFAX.When the number of characters in the email message received by IFAX is less than the specified number of characters, the message is ignored and is not printed or transferred.When a number other than "0" is specified for the number of characters and the email message disappeared, and also when no TIFF file exists, a blank page with header and footer is printed and transferred.* A kanji character is recognized as a two-byte character. A control code such as CR is also included in the number of characters.
Setting range:0 to 999 (Unit: number of characters)0: Do not ignore the email message.Factory setting value: 0
1
BOX-BKUP For restore control of the BOX backup function. 1
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-39
SCANTYPE Switch the type of reader.This is a service mode used to change the default reader to the optional reader.Use this mode to change the CIS reader to CCD reader.
Setting range:0: default reader1: Optional readerFactory setting value: 0
1
GR-ADJ-L Specify the gain setting level for linearity of Red color on the backside. Specify the gain setting level to adjust linearity of the image on the backside against the image on the front side.
1
RAG-CONT Set the level of fixing smear control mode.0: No smear1: Small level of smear2: Middle level of smear3: Large level of smear
1
OR-ADJ-L Specify the offset setting level for linearity of Red color on the backside. Specify the offset setting level to adjust linearity of the image on the backside against the image on the front side.Setting value: -5 to 5 (default: 0) 1
ABC-MD2 Adjust the level of base density correction level for reading the backside. Setting value: -1 to 3 (default: 0) 1
MXSPDSEL To set the skew correction (the idle rotation setting) for different paper width mixed in the original tray.When the skew movement found, perform the idle rotation (additional 2 rotations) in the DF path to increase the paper loop counts of the registration roller; this will correct the skew movement.Setting:0: w/ idle rotation [default]1: w/o idle rotation
1
PO-CNTMD Use it to select the number of times the potential control mechanism goes on.0: once at power-on1: once at power-on and, in addition, 10 and 60 min thereafter (simplified potential control mode)2: once at power-on and, in addition, 10 and 60 min thereafter (normal potential control mode; default) 2
W-CLN-P Use it to set the interval at which the primary charging wire is automatically cleaned.setting: every 100 to 2000 (sheets; default at 2000) 2
IDL-MODE Use it to select idle rotation mode for the developing assembly.0: fix to low humidity mode (off)1: environment control (default)2: fix to normal temperature/humidity mode (idle rotation for 120 sec)3: fix to high humidity mode (idle rotation for 300 sec)4: power save mode
2
FSPD-S1 Use it to select fixing enhancement mode.0: normal (default)1: fixing enhancement mode2: not used
2
TSPLY-SW Use it to switch over toner supply sequence.0: environment control (default)1: fix to low humidity mode (on for 1.4 sec, off for 1 sec)2: fix to normal temperature/humidity mode (on for 1.5 sec, off for 1 sec)3: fix to high humidity mode (on for 3 sec, off for 2 sec)
2
SCANSLCT Use it to enable/disable the function used to compute the scan area from the selected paper size.setting0: off (determine scan area by original detection)1: on (determine scan area by paper size)
2
OHP-TEMP Use it to switch over control temperature for transparency mode.setting0: normal (default); 1: -5 deg C; 2: -10 deg C; 3: -15 deg C; 4: -20 deg C 2
SENS-CNF Use it to set the arrangement of original sensors.setting0: AB (default)1: inch
2
RAW-DATA Use it to specify how received data should be printed.If a received image has a fault, use this mode to find out if the fault is in the data or in image processing.setting0: normal operation (default)1: print as is
2
SHARP Use it to change the level of sharpness (median value).setting: 1 to 5 2
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-40
LAPC-SW Use it to switch over laser APC correction.0: execute initial rotation APC if left alone for 10 min1: execute initial rotation APC if left alone for 60 min (default)2: execute initial rotation if left alone for 120 min3: disable initial rotation APC only4: disable
2
FDW-DLV Use it to select face-up delivery or face-down delivery when the count is set to multiple.setting0: normal (for a single original, face-up for all; default)1: for a single original, face-up delivery if the count is set to '1'; otherwise, face-down
2
COTDPC-D This item is for use at the factory.setting: 0 to 3 (default: 0) 2
EVL-VDT Use it to switch over drum target potential to suit the environment of the site.setting: 0 to 6 (default: 1) 2
RMT-LANG Use it to change the language for the remote UI to be used through the Web browser.Select the particular language using the + and - keys. 2
HI-HUME Use it to change the developing bias frequency.If a separation fault occurs in a high humidity environment, set it to '1'.setting0: 2700 Hz (default); 1: 200 Hz
2
IFAX-LIM Use it to limit the number of output lines if an excess volume of data is received through i-fax.setting: 0 to 999 (default: 500)0: no limit
2
DF-BLINE Use it execute a remedial measure in response to black lines caused by dust on the platen roller when the ADF is use (stream reading mode).setting0: disable (default)1: enable
2
DRM-H-SW Use it to enable/disable the nighttime drum heater.0: enable drum heater1: turn on/off drum heater in keeping with environment (default)2: disable drum heater
2
SMTPTXPN Use it to change the SMTP transmission port number.setting: 0 to 65535 2
SMTPRXPN Use it to change the SMTP reception port number.setting: 0 to 65535
2
POP3PN Use it to change the POP reception port number.setting: 0 to 65535 2
RUI-DSP Use it to enable/disable a remote IU function (designed for the Disabilities Act).setting0: do not show Copier screen on remote UI (default)1: show Copier screen
2
ORG-LGL Use it set a special paper size that the ADF cannot recognize (applicable to LGL communicated by the ADF).setting0: LGL (default)1: FOOLSCAP2: A-FOOLSCAP3: FOLIO4: G-LEGAL5: OFFICIO6: E-OFFICIO7: A-OFFICIO8: B-OFFICIO9: A-LEGAL10: M-OFFICIO
2
ORG-LTR Use it to set a special paper size that the ADF cannot recognize (applicable to LTR communicated by the ADF).setting0: LTR (default)1: G-LTR2: A-LTR3: EXECUTIVE
2
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-41
ORG-LTRR Use it to set a special paper size that the ADF cannot recognize (applicable to LTR-R communicated by the ADF).setting0: LTR-R (default)1: G-LTR-R2: A-LTR-R3: EXECUTIVE-R
2
ORG-B5 Select a special paper size that the ADF cannot recognize (applicable to B5 communicated by the ADF).setting0: B5 (default)1: K-LEGAL
2
UI-BOX Use it to enable/disable the display of the box screen on the control panel.setting0: do not display1: display (default)2: do not display (however, permit storage of PDF job in box)
2
UI-SEND Use it to enable/disable display of the transmission screen on the control panel.setting0: do not display1: display (default)
2
UI-FAX Use it to enable/disable display of the fax screen on the control panel.setting0: do not display1: display (default)
2
NW-SPEED Use it to select the appropriate data transmission speed when a connection is made to a service network.setting0: auto (default)1: 100Base-Tx2: 10Base-T
2
STS-PORT Use it to enable/disable the port for TOT synchronous command communications.setting0: disable (off; default)1: enable (on)
2
CMD-PORT Use it to enable/disable the port for TOT asynchronous status communications.Use it to enable/disable the port for asynchronous status communications when FTUIF-over-TCP/IP is in use.setting0: disable (off; default)1: enable (on)
2
MODELSZ2 Use it to enable/disable platen board original size detection (for global support; AB/inch mix).setting0: disable global detection (default)1: enable global detection
2
SZDT-SW Use it to enable/disable switchover of CCD size detection and photo size detection for platen board original size detection.setting0: disable photo size detection1: enable photo size detection
2
NS-CMD5 Use it to limit the use of CRAM-MD5 authentication for SMTP authentication.setting0: as determined by SMTP server (default)1: do not use
2
NS-GSAPI Use it to limit the use of GSSAPI authentication for restrictive SMTP authentication as part of GSSAPI authentication of SMTP authentication.setting0: as determined by SMTP server (default)1: do not use
2
NS-NTLM Use it to limit the use of NTLM authentication for SMTP authentication.setting0: as determined by SMTP server (default)1: do not use 2
NS-PLNWS Use it to limit the use of PLAIN, LOGIN authentication, which is plain-text authentication of SMTP authentication (however, only where PLAIN, LOGIN authentication restrictive communication packets are encrypted).setting0: as determined by SMTP server (default)1: do not use
2
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-42
NS-PLN Use it to limit the use of PLAIN, LOGIN authentication, which is plain-text authentication of SMTP authentication (however, only where PLAIN, LOGIN authentication restrictive communication packets are not encrypted).setting0: as determined by SMTP server (default)1: do not use
2
NS-LGN Use it to limit the use of LOGIN authentication for restrictive SMTP authentication of LOGIN authentication.setting0: as determined by SMTP server (default)1: do not use
2
MEAP-PN Use it to change the HTTP port number of a MEAP application.setting: 0 to 65535 (default: 8000) 2
SVMD-ENT Use it to see how to start service mode:setting0: User Mode key -> 2 and 8 keys at the same time -> User Mode key (default)1: User Mode key -> 4 and 9 keys at the same time -> User Mode key
2
SSH-SW Use it to enable/disable the SSH server function.Setting0: off (default)1: on
2
RMT-LGIN Use it to turning the SSH server function ON or OFF.Setting0: off (default)1: on
2
RE-PKEY Use it to enable/disable regeneration of the SSH server key.setting0: off (default)1: on
2
U-NAME Use it to set user names permitting connection to the SSH server.setting8 characters max. (alphanumeric)
2
U-PASWD Use it to set user passwords permitting connection to the SSH server.setting8 characters max. (alphanumeric)
2
DA-PORT Use it to enable/disable the port for TOT asynchronous status communication.setting0: close (default)1: open (w/ DA installed)
2
DA-CNCT Use it to set the DA.setting0: off (default)1: on
2
CHNG-STS Use it to set the TOT status connection port number.setting1 to 65535 (default: 20010)
2
CHNG-CMD Use it to set the TOT command connection port number.setting1 to 65535 (default: 20000)
2
MEAP-DSP Use it to enable/disable a shift from the MEAP to native screen.setting0: off (shift to native seen; default)1: on (do not shift to native screen)
2
ANIM-SW Use it to enable/disable display of the Error/Jam screen with a MEAP application in operation.setting0: off (display warning screen; default)1: on (do not display warning screen)
2
MEAP-SSL Use it to set the HTTPS port for MEAP.setting0 to 65535 (default: 8443)
2
STNBY-TM Use it to switch over the standby shift time.setting0: normal (default)1: increase standby shift time until possibility of image distortion is absent
2
KSIZE-SW Use it to enable/disable support of K paper.setting0: do not support K paper (default)1: support K paperprocedure1) Set '0' in this service mode. 2) Set '0' for the following: COPIER > OPTION > BODY > MODEL-SZ.3) Perform the shut-down sequence, and turn off and then on the main power.
2
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-43
POST-DWN A countermeasure mode to prevent smudges from appearing on the lead edge of an image (caused by pre-transfer upper guide) in the HH environment
Decrease the post high pressure output value from 280uA to 70uA only in the HH environment, as an individual countermeasure, in order to prevent smudges from appearing on the lead edge of an image caused by the pre-transfer upper guide.0: Normal (default)1: Countermeasure mode (A post high pressure value is automatically changed when an HH environment is detected by the environment sensor.)
2
IMP-MISS Set OFF/ON for detection of "unmatched" error in the number of printouts.Setting value:0: OFF [default]1: ON
2
UI-PRINT Control the display of a print job screen on the control panel.Use this mode to set whether or not to display a print job screen on the control panel.This mode is available for a user who does not want to display a print job screen on the control panel.Setting range:0: Do not display the screen.1: Display the screen.[default]
2
WUEV-SW Set whether or not to make a sleep notification.Set whether or not to make a sleep notification to the DS application on the network when the copying machine main unit switched its operation to or recovered from sleep operation.Setting range:0, 1 (0: Make a sleep notification. 1: Do not make a sleep notification.)Factory setting value: 0
2
WUEV-INT Set the interval for a sleep notification.Set the interval for a sleep notification when "0" is set to WUEV-SW.Setting range: 0 to 65535 (Unit: second)Factory setting value: 600
2
WUEV-POT Set the port number for the destination of a sleep notification.Set the port number for the destination of a sleep notification when "0" is set to WUEV-SW.Setting range: 0 to 65535Factory setting value: 11427 2
WUEV-RTR Set the range of a sleep notification.Set the number of routers used to make a sleep notification when "0" is set to WUEV-SW.Setting range: 1 to 255Factory setting value: 3
2
SJB-UNW Switch the number of secure print jobs to be accumulated (scheduled number of jobs).Set "50" or "90" for the upper limit in the number of secure print jobs to be accumulated (scheduled number of jobs).Setting range:0: 501: 90Factory setting value: 0
2
UI-RSCAN Control the display of a remote scanning screen on the control panel.Set whether or not to display a remote scanning screen on the control panel.This mode is available for a user who does not want to display the screen on the control panel.Setting range:0: Do not display the screen.1: Display the screen.Factory setting value: 1
2
UI-EPRNT Control the display of an extended printing screen (EFI printing screen) on the control panel.Set whether or not to display an extended printing screen (EFI printing screen) on the control panel.This mode is available for a user who does not want to display the screen on the control panel.[Additional Information]In this screen, the conventional UI-EXT was divided into UI-RSCAN and UI-EPRNT so that each control can be performed separately.Setting range:0: Do not display the screen.1: Display the screen.Factory setting value: 1
2
UI-WEB Control the display of a Web browser screen on the control panel.Set whether or not to display a Web browser screen on the control panel.This mode is available for a user who does not want to display the screen on the control panel.Setting range:0: Do not display the screen.1: Display the screen.Factory setting value: 1
2
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-44
<USER>
T-17-52
WEBV-SW Set whether or not to use the WEBDAV function.When 1 (ON) is set to this mode, the WEBDAV function is unavailable. (WEBDAV related information disappears from the following items.- User mode -> Setting of destination list specifications -> Registration of destinations -> File -> "WEBDAV" in the protocol- User mode -> "Use the chunk split transmission for WEBDAV transmission" in the setting of specifications for transmission[Reference]The WEBDAV function is installed in the main unit as standards, but there are cases when this function is not used in order to reduce the memory usage.Setting range:0: Use the WEBDAV function.1: Do not use the WEBDAV function.Factory setting value: 0
2
CARD-RNG Set the number of available cards.Set the number of available cards used for card reader.Setting range: 1 to 1000Factory setting value: 1000
2
WUEN-LIV Set the activation period after a sleep notification is made from the network.Set the period until when the copying machine main unit is placed in the sleep mode next time after activated in the sleep mode from the network without jobs entered.Setting range: 10 to 600 (Unit: second)Factory setting value: 15
2
MAILYEAR Enter the year/month/date in the subject and file name of an email. (Specifications for Santander Bank in Mexico)Automatically add the year/month/date, time, and allocation number at the end of characters specified for the subject and file name of an email.Setting range:0: Do not add the year/month/date.1: Add the year/month/date.
2
SEND-AUT Switch the setting of user authentication to use SEND function.When setting the switch of this mode to ON (1), a guest button is displayed in the login screen for MEAP, with which user authentication for SEND function is executed. (Only authentication for SEND function can be executed.)If you do not want to use SEND function, press this button so that you can perform login without using an ID and password.[Remarks] When you perform login using the guest button, the setting in this mode does not function.Setting range:0 (Do not display the guest button.) / 1 (Display the guest button.)Factory setting value: 0
2
DHCP-12 Set whether or not to validate the DHCP-Option 12 request.When the DHCP-12 switch is set to ON, an inquiry about a host name (Option 12) is made by using the DHCP-Option 55.*DHCP (Dynamic Host Configuration Protocol)Setting range:0: OFF, 1: ONFactory setting value: 1
2
DHCP-81 Set whether or not to validate the DHCP-Option 81 request.When the DHCP-81 switch is set to ON and the dynamic DNS setting is set to ON in the user mode, dynamic change of an IP address by DHCP Option 81 is validated.Setting range:0: OFF, 1: ONFactory setting value: 1
2
USB-RCNT Set whether or not to perform automatic connection when disconnecting the USB device. (USB RECONNECT)Setting range:0: Do not perform automatic connection.1: Perform automatic connection.Factory setting value: 0
2
UI-COPY Make a setting to switch the display in the copy screen in the control panel.This mode is available for a user who does not want to display a print job screen on the control panel.Setting range:0: Hide the copy screen.1: Do not hide the copy screen.[default]
2
PP-LWRT Not used 2
COPIER > OPTION >USERSub-item Description LevelCOPY-LIM Use it to put an upper limit to the number of copies.
setting: 1 to 9999 (default: 9999) 1
SLEEP Use it to enable/disable the sleep function.setting0: off1; on (default)
1
COPIER > OPTION > BODYSub-item Description Level
Chapter 17
17-45
WEB-DISP Use it to enable/disable the fixing web length warning message.setting0: off (do not display)1: on (display; default)If set to '0', the message will only be on the service mode screen.
1
W-TONER Use it to enable/disable the collecting toner case full message.setting0: off (do not display)1: on (display; default)If set to '0', the message will be only on the service mode screen.
1
COUNTER1 Use it to set soft counter 1 of the user mode screen.101: total 1 (fixed) 1
COUNTER2 Use it to set soft counter 2 of the user mode screen.setting: 0 to 999 1
COUNTER3 Use it to set soft counter 3 of the user mode screen.setting: 0 to 999 1
COUNTER4 Use it to set soft counter 4 of the user mode screen.setting: 0 to 999 1
COUNTER5 Use it to set soft counter 5 of the user mode screen.setting: 0 to 999 1
COUNTER6 Use it to set soft counter 6 of the user mode screen.setting: 0 to 999 1
CONTROL Not used1
B4-L-CNT Use it to specify where B4 should be counted as large or small size for soft counters 1 thorough 6.0: count as small size (default)1: count as large size
1
COPY-JOB Use it to enable/disable copy job reservation with a card reader/coin vendor in use.setting0: enable copy job reservation (default)1: disable copy job reservation
1
PR-PSESW Use it to enable/disable the print pause function switch.setting0: disable print pause function (default)1: enable print pause function (display print output stop/resume button on user screen)
1
IDPRN-SW Use it to switch over count increment jobs for the group control counter.0: for PRINT, increment the following: box print, report print, SEND local print, PDL print (default)1: for PRINT, increment the following: report print, SEND local print, PDL print 1
CNT-SW Use it to switch over display of charge counter default items.setting0: default total 1 (101; default)1: default total 2 (102), copy total 2 (202), total A total 2 (127)2: default total 1 (101), total small (104), total large (103), scan total 1 (501)
1
TAB-ACC Use it to enable/disable automatic switchover of cassettes for tab (index) paper.setting0: do not change over between tab sheets (default)1: change over between tab sheets
1
REMPNL Use it to enable/disable the remote panel function.0: off (default)1: on
1
BCNT-AST Use it to switch over job types for the count of the box prints with ASSIST in use.setting0: count as PDL job (default)1: count as copy job
1
DOC-REM Use it to enable/disable the Remove Original message.setting0: do not indicate (default)1: indicate
1
FROM-OF Set whether or not to delete a "from" address for email transmission.Setting value:0: Do not delete a "from" address. (default)1: Delete a "from" address.
1
COPIER > OPTION >USERSub-item Description Level
Chapter 17
17-46
FILE-OF Set whether or not to prohibit email transmission to the file address.Prohibit transmission to the file address by prohibiting input of the file address from the address book.Setting value:0: Do not prohibit transmission. (default)1: Prohibit transmission.If a file address has been already registered, the address can be used even after this mode is set to "1". Therefore, delete the address manually.
1
MAIL-OF Set whether or not to prohibit transmission to the email address.Prohibit transmission to the email address by prohibiting input of the email address from the address book.Setting value:0: Do not prohibit transmission. (default)1: Prohibit transmission.If an email address has been already registered, the address can be used even after this mode is set to "1". Therefore, delete the address manually.
1
IFAX-OF Set whether or not to prohibit transmission to the IFAX address.Prohibit transmission to the IFAX address by prohibiting input of the IFAX address from the address book.Setting value:0: Do not prohibit transmission. (default)1: Prohibit transmission.If an IFAX address has been already registered, the address can be used even after this mode is set to "1". Therefore, delete the address manually.
1
LDAP-DEF Switch the default value of the LDAP server search condition.Change the default condition for the attribute specified to search detailed information of the LDAP server.Setting value:0: "Name" (default)1: "Email"2: "FAX"3: "Organization"4: "Organization unit"5: User setting 16: User setting 2
1
HDCR-DSW Set whether or not to display the menu of "ON/OFF of complete HDD deletion" in the user mode.User mode > System administration settings > Complete HDD deletionSetting value:0: Do not display the menu.1: Display the menu.Factory setting value: 0
1
SIZE-DET Use it to enable/disable original size detection.0: disable original size detection1: enable original size detection
2
DATE-DSP Use it to switch over data indication format:setting.0: 'YY MM/DD1: DD/MM 'YY2: MM/DD/YY
2
MB-CCV Use it to limit the users of the control cards for mail boxes.setting0: do not limit (default)1: limit
2
TRY-STP Use it to switch over operation when the finisher tray becomes full.setting0: normal (suspend operation when finisher tray becomes full; default)1: suspend in relation to height detection2: do not suspend
2
MF-LG-ST Use it to set the Extra Length key.setting0: normal (default)1: indicate Extra Length key on supported mode screens
2
CNT-DISP Use it to enable/disable indication of a serial number in response to a press on the Counter Check key.setting0: display serial number (default)1: do not display serial number
2
PH-D-SEL Select the number of lines for printing in photo mode.0: 141 lines (default)1: 134 lines
2
OP-SZ-DT Use it to enable/disable original size detection for book mode.setting0: off (require input of size on control panel; default)1: on (use auto original size detection)
2
COPIER > OPTION >USERSub-item Description Level
Chapter 17
17-47
NW-SCAN Use it to permit/not permit the network scan function.setting0: do to permit network scan function (default)1: permit network scan function
Caution:For the Japanese model, the value cannot be changed.For a non-Japanese model, PSPCL is fixed to '1'; the value may be changed on other models.
2
HDCR-DSP Use it to set how HDD full deletion mode may operate.1: using 0s, delete once (default)2: using random data, delete once3: using random data, delete 3 times
2
JOB-INVL Use it to set the interval of jobs for an interrupt.setting0: standard (at time of interrupt copy, continuously output next jobs; default)1: output next job only after delivering last sheet of interrupt copy2: output next job only after delivering last sheet of all jobs
2
PCL-COPY Use it to set PCL command COPIES Meru/Pintubo/Hood compatibility.0: use page-based control according to COPIES command value specified for each page (default)1: Meru/Pinatubo/Hood compatibility mode2 to 6535: reserved
2
PRJOB-CP Use it to set the CCV count pulse generation for reception and report output.setting0: do not generate count pulse (default)1: generate count pulse
2
DPT-ID-7 Use it to select the 7-character input method for group ID registration and authentication.setting0: normal (default)1: use 7-character input
2
RUI-RJT Use it to enable/disable connection of the HTTP port at 3 failed attempts at authentication by the RUI.setting0: make invalid (default)1: keep valid
2
CTM-S06 Use it to specify whether a password should be removed from the export file (file transmission address).setting0: do not remove password from export file (default)1: remove password from export file
2
FREG-SW Use it to enable/disable display of the free area of the MEAP counter (SEND).setting0: do not display (default)1: display
2
IFAX-SZL Use it to limit transmission size for i-fax transmission.setting0: keep transmission size limit valid (using server/not using server)1: keep transmission size limit invalid (only when not using server; default)
2
IFAX-PGD Use it o enable/disable page-based division transmission (only when the transmission data size upper limit is exceeded).setting0: do not permit page-based division transmission in i-fax simple mode (default)1: enable page-based division transmission in i-fax simple mode 2
MEAPSAFE Use it to enable/disable switchover to safe mode for MEAP.0: off (default)1: on (safe mode)
2
AFN-PSWD Use it to limit access to user mode.setting0: off (shift to user mode screen without prompting for password; default)1: on (shift to user mode after password match)
2
PTJAM-RC Use it to enable/disable PDL jam recovery.setting0: off (disable recovery)1: on (enable recovery; default)
2
SLP-SLCT Use it enable/disable use of an existing network-based application.setting0: do not use (default)1: use
When set to '1', no shift takes place to sleep mode 3.
2
COPIER > OPTION >USERSub-item Description Level
Chapter 17
17-48
Soft Counter Specifications100s: total200s: copy (as needed, add 001 and up)300s: print400s: copy + print500s: scan600s: box print700s: reception print800s: report print900s: transmission<Guide to Symbols>Yes: counter used in the machine.large size: paper larger than B4.small size: paper that is B4 or smaller.numbers 1 and 2 under Description indicate the count for large size paper.(The machine may be set so that it will count B4 and larger paper as a large size paper in service mode: COPIER>OPTION>USER>B4-L-CNT).total A: total excluding local copy + remote copy.total B: total excluding local copy + remote copy + box print.copy: local copy + remote copy.copy A: local copy + remote copy + box print.
PS-MODE Use it to set PS compatibility mode.setting0: not compatible (default)1: offer PS type 3 halftone command compatibility (dither reverse)2: compatible with priority on resolution3: reserved4: compatible for EFI landscape/portrait mix5 to 65535: reserved
2
CNCT-RLZ Use it to enable/disable the use of the connection serialization function.setting0: off (disable connection serialization function; default)1: on (enable connection serialization function)
2
INS-C/S Expand the inserter function. (Only for a finisher inserter)Setting value:0: Front cover only (default)1: Multiple inserters of "front cover + inserted cover"MEMO:- This mode is only available for a finisher inserter. (A perfect binder inserter always supports multiple inserters of "front cover + inserted cover".)- This setting is validated for both copying and printing operation.
2
PDL-NCSW Set the card management mode for print jobs.Control PDL print jobs using a New Card.
- Conventional operationA PDL print job was received by the machine and printing was performed, regardless of whether or not a New Card was inserted. (Job entry was controlled by the driver on the host side.)- Operation after changeWhen this mode is set to "0", the machine operates in the same manner as the conventional operation.When this mode is set to "1" and when a card is not inserted and the section ID does not match the card ID, printing is not performed.When this mode is set to "1" and when the card ID does not match the section ID of the job after a card is inserted, printing is performed.
Setting range:0: A PDL print job is received by the machine and printing is performed regardless of whether or not a New Card is inserted. [Factory setting value / Value after RAM clear]1: When a card is not inserted and the section ID does not match the card ID, printing is not performed.Factory setting value: 0
2
DOM-ADD Set whether or not to supplement the destination domain for email transmission.Perform transmission with an address in which the address entered for email transmission and the domain specified in the user mode (ex. @xxxx.co.jp) are combined.Setting value:0: Do not supplement the domain. (default)1: Supplement the domain.<To send email to "aaaa@xxxx.co.jp">1) Specify "xxxx.co.jp" for the domain in the user mode, and specify "1" for this mode.2) If "aaaa" is entered for email transmission, the address is supplemented as "aaaa@xxx.co.jp".
2
CLR-TIM Set the timing of complete deletion of processing data.Select the timing to execute complete deletion using the security kit.When complete deletion is executed, performance of job processing may decrease depending on the data. This occurs because processed page data is deleted during job processing and much load is applied to the processing to access the CPU or HDD. When this processing is performed after job processing is completed, job processing capability can be improved.Setting range: 0, 1 (0: Delete data during job processing. 1: Delete data after job processing is completed.)Factory setting value: 0
2
COPIER > OPTION >USERSub-item Description Level
Chapter 17
17-49
print: PDL print + report print + box print.print A: PDL print + report print.scan: black-and-white scan + color scan
T-17-53
COPIER > COUNTERNo. Description Level101 total 1 Yes102 total 2 Yes103 total (large) Yes104 total (small) Yes105 total (full color 1)106 total (full color 2)108 total (black-and-white 1) Yes109 total (black-and-white 2) Yes110 total (mono color; large)111 total (mono color; small)112 total (back-and-white; large) Yes113 total (black-and-white; small) Yes114 total 1 (duplex) Yes115 total 2 (duplex) Yes116 large (duplex) Yes117 small (duplex) Yes118 total (mono color 1)119 total (mono color 2)120 total (full color; large)121 total (full color; small)122 total (full color + mono color; large)123 total (full color + mono color; small)124 total (full color + mono color 2)125 total (full color + mono color 1)126 total A1 Yes127 total A2 Yes128 total A (large) Yes129 total A (small) Yes130 total A (full color 1)131 total A (full color 2)132 total A (black-and-white 1) Yes133 total A (black-and-white 2) Yes134 total A (mono color; large)135 total A (mono color; small)136 total A (black-and-white; large) Yes137 total A black-and-white; small) Yes138 total A1 (duplex)139 total A2 (duplex)140 large A (duplex)141 small A (duplex)142 total A (mono color 1)143 total A (mono color 2)144 total A (full color; large)145 total A (full color; small)146 total A (full color + mono color; large)147 total A (full color + mono color; small)148 total A (full color + mono color 2)149 total A (full color + mono color 1)150 total B1 Yes151 total B2 Yes152 total B (large) Yes153 total B (small) Yes154 total B (full color 1)155 total B (full color 2)156 total B (black-and-white 1) Yes157 total B (black-and-white 2) Yes158 total B (mono color; large)159 total B (mono color ; small)160 total B (black-and-white; large) Yes161 total B (black-and-white; small) Yes162 total B1 (duplex)
Chapter 17
17-50
163 total B2 (duplex)164 large B (duplex)165 small B (duplex)166 total B (mono color 1)167 total B (mono color 2)168 total B (full color; large)169 total B (full color; small)170 total B (full color + mono color; large)171 total B (full color + mono color; small)172 total B (full color + mono color 2)173 total B (full color + mono color 1)201 copy (total 1) Yes202 copy (total 2) Yes203 copy (large) Yes204 copy (small) Yes205 copy A (total 1) Yes206 copy A (total 2) Yes207 copy A (large) Yes208 copy A (small) Yes209 local copy (total 1) Yes210 local copy (total 2) Yes211 local copy (large) Yes212 local copy (small) Yes213 remote copy (total 1) Yes214 remote copy (total 2) Yes215 remote copy (large) Yes216 remote copy (small) Yes217 copy (full color 1)218 copy (full color 2)219 copy (mono color 1)220 copy (mono color 2)221 copy (black-and-white 1) Yes222 copy (black-and-white 2) Yes223 copy (full color; large)224 copy (full color; small)225 copy (mono color; large)226 copy (mono color; small)227 copy (black-and-white; large) Yes228 copy (black-and-white; small) Yes229 copy (full color + mono color; large)230 copy (full color + mono color; small)231 copy (full color + mono color/2)232 copy (full color + mono color/1)233 copy (full color; large; duplex)234 copy (full color; small; duplex)235 copy (mono color; large; duplex)236 copy (mono color; small; duplex)237 copy (black-and-white; large; duplex)238 copy (black-and-white; small; duplex)245 copy A (full color 1)246 copy A (full color 2)247 copy A (mono color 1)248 copy A (mono color 2)249 copy A (black-and-white 1) Yes250 copy A (black-and-white 2) Yes251 copy A (full color; large)252 copy A (full color; small)253 copy A (mono color; large)254 copy A (mono color; small)255 copy A (black-and-white; large) Yes256 copy A (black-and-white; small) Yes257 copy A (full color + mono color; large)258 copy A (full color + mono color; small)259 copy A (full color + mono color 2)260 copy A (full color + mono color 1)
COPIER > COUNTERNo. Description Level
Chapter 17
17-51
261 copy A (full color; large; duplex)262 copy A (full color; small; duplex)263 copy A (mono color; large; duplex)264 copy A (mono color; small; duplex)265 copy A (black-and-white; large; duplex)266 copy A (black-and-white; small; duplex)273 local copy (full color 1)274 local copy (full color 2)275 local copy (mono color 1)276 local copy (mono color 2)277 local copy (black-and-white 1) Yes278 local copy (black-and-white 2) Yes279 local copy (full color; large)280 local copy (full color; small)281 local copy (mono color; large)282 local copy (mono color; small)283 local copy (black-and-white; large) Yes284 local copy (black-and-white; small) Yes285 local copy (full color + mono color; large)286 local copy (full color + mono color; small)287 local copy (full color + mono color 2)288 local copy (full color + mono color 1)289 local copy (full color; large; duplex)290 local copy (full color; small; duplex)291 local copy (mono color; large; duplex)292 local copy (mono color; small; duplex)293 local copy (black-and-white; large; duplex)294 local copy (black-and-white; small; duplex)002 remote copy (full color 1)003 remote copy (full color 2)004 remote copy (mono color 1)005 remote copy (mono color 2)006 remote copy (black-and-white 1) Yes007 remote copy (black-and-white 2) Yes008 remote copy (full color; large)009 remote copy (full color; small)010 remote copy (mono color; large)011 remote copy (mono color; small)012 remote copy (black-and-white; large) Yes013 remote copy (black-and-white; small) Yes014 remote copy (full color + mono color; large)015 remote copy (full color + mono color; small)016 remote copy (full color + mono color 2)017 remote copy (full color + mono color 1)018 remote copy (full color; large; duplex)019 remote copy (full color; small; duplex)020 remote copy (mono color; large; duplex)021 remote copy (mono color; small; duplex)022 remote copy (black-and-white; large; duplex)023 remote copy (black-and-white; small; duplex)301 print (total 1) Yes302 print (total 2) Yes303 print (large) Yes304 print (small) Yes305 print A (total 1) Yes306 print A (total 2) Yes307 print A (large) Yes308 print A (small) Yes309 print (full color 1)310 print (full color 2)311 print (mono color 1)312 print (mono color 2)313 print (black-and-white 1) Yes314 print (black-and-white 2) Yes315 print (full color; large)
COPIER > COUNTERNo. Description Level
Chapter 17
17-52
316 print (full color; small)317 print (mono color; large)318 print (mono color; small)319 print (black-and-white; large) Yes320 print (black-and-white; small) Yes321 print (full color + mono color; large)322 print (full color + mono color; small)323 print (full color + mono color/2)324 print (full color + mono color/1)325 print (full color; large; duplex)326 print (full color; small; duplex)327 print (mono color; large; duplex)328 print (mono color; small; duplex)329 print (black-and-white; large; duplex)330 print (black-and-white; small; duplex)331 PDL print (total 1) Yes332 PDL print (total 2) Yes333 PDL print (large) Yes334 PDL print (small) Yes335 PDL print (full color 1)336 PDL print (full color 2)339 PDL print (black-and-white 1) Yes340 PDL print (black-and-white 2) Yes341 PDL print (full color; large)342 PDL print (full color; small)345 PDL print (black-and-white; large) Yes
346 PDL print (black-and-white;small) Yes
351 PDL print (full color; large; duplex)352 PDL print (full color; small; duplex)355 PDL print (black-and-white; large; duplex)356 PDL print (black-and-white; small; duplex)401 copy + print (full color; large)402 copy + print (full color; small)403 copy + print (black-and-white; large)404 copy + print (black-and-white; small)405 copy + print (black-and-white 2)406 copy + print (black-and-white 1)407 copy + print (full color + mono color; large)408 copy + print (full color + mono color; small)409 copy + print (full color + mono color/2)410 copy + print (full color + mono color/1)411 copy + print (large)412 copy + print (small)413 copy + print (2)414 copy + print (1)415 copy + print (mono color; large)416 copy + print (mono color; small)417 copy + print (full color; large; duplex)418 copy + print (full color; small; duplex)419 copy + print (mono color; large; duplex)420 copy + print (mono color; small; duplex)421 copy + print (black-and-white; large; duplex)422 copy + print (black-and-white; small; duplex)501 scan (total 1) Yes502 scan (total 2) Yes503 scan (large) Yes504 scan (small) Yes505 black-and-white scan (total 1) Yes506 black-and-white scan (total 1) Yes507 black-and-white scan (total 2) Yes508 black-and-white scan (large) Yes509 black-and-white scan (small)510 color scan (total 1)511 color scan (total 2)512 color scan (large)
COPIER > COUNTERNo. Description Level
Chapter 17
17-53
601 color scan (small) Yes602 box print (total 1) Yes603 box print (total 2) Yes604 box print (large) Yes605 box print (small)606 box print (full color 1)607 box print (full color 2)608 box print (mono color 1)609 box print (black-and-white 1) Yes610 box print (black-and-white 2) Yes611 box print (full color; large)612 box print (full color; small)613 box print (mono color; large)614 box print (mono color; small)615 box print (black-and-white; large) Yes616 box print (black-and-white; small) Yes617 box print (full color + mono color; large)618 box print (full color + mono color; small)619 box print (full color + mono color 2)620 box print (full color + mono color 1)621 box print (full color; large; duplex)622 box print (full color; small; duplex)623 box print (mono color; large; duplex)624 box print (mono color; small; duplex)625 box print (black-and-white; large; duplex)626 box print (black-and-white; small; duplex)701 reception print (total 1) Yes702 reception print (total 2) Yes703 reception print (large) Yes704 reception print (small) Yes705 reception print (full color 1)706 reception print (full color 2)707 reception print (grayscale 1)708 reception print (grayscale 2)709 reception print (black-and-white 1) Yes710 reception print (black-and-white 2) Yes711 reception print (full color; large)712 reception print (full color; small)713 reception print (grayscale; large)714 reception print (grayscale; small)715 reception print (black-and-white; large) Yes716 reception print (black-and-white; small) Yes717 reception print (full color + grayscale; large)718 reception print (full color + grayscale; small)719 reception print (full color + grayscale 2)720 reception print (full color + grayscale 1)721 reception print (full color; large; duplex)722 reception print (full color; small; duplex)723 reception print (grayscale; large; duplex)724 reception print (grayscale; small; duplex)725
reception print (black-and-white; large; duplex)726
reception print (black-and-white; small; duplex)801 report print (total 1) Yes802 report print (total 2) Yes803 report print (large) Yes804 report print (small) Yes805 report print (full color 1)806 report print (full color 2)807 report print (grayscale 1)808 report print (grayscale 2)809 report print (black-and-white 1) Yes810 report print (black-and-white 2) Yes811 report print (full color; large)812 report print (full color; small)
COPIER > COUNTERNo. Description Level
Chapter 17
17-54
813 report print (grayscale; large)814 report print (grayscale; small)815 report print (black-and-white; large) Yes816 report print (full color + grayscale; large) Yes817 report print (full color + grayscale; small)818 report print (full color + grayscale; small)819 report print (full color + grayscale 2)820 report print (full color; large; duplex)821 report print (full color; large; duplex)822 report print (full color; small; duplex)823 report print (grayscale; large; duplex)824 report print (grayscale; small; duplex)825 report print (black-and-white; large; duplex)826 report print (black-and-white; small; duplex)901 copy scan total 1 (color)902 copy scan total 1 (black-and-white)903 copy scan total 2 (color)904 copy scan total 2 (black-and-white)905 copy scan total 3 (color)906 copy scan total 3 (black-and-white)907 copy scan total 4 (color)908 copy scan total 4 (black-and-white)909 local copy scan (color)910 local copy scan (black-and-white)911 remote copy scan (color)912 remote copy scan (black-and-white)913 transmission scan total 1 (color)914 transmission scan total 1 (black-and-white)915 transmission scan total 2 (color)916 transmission scan total 2 (black-and-white) Yes
917 transmission scan total 3 (color)918 transmission scan total 3 (black-and-white) Yes919 transmission scan total 4 (color)920 transmission scan total 4 (black-and-white)921 transmission scan total 5 (color)922 transmission scan total 5 (black-and-white) Yes929 transmissions scan total 6 (color)930 transmission scan total; 6 (black-and-white) Yes931 transmission scan total 7 (color)932 transmission scan total 7 (black-and-white)933 transmission scan total 8 (color)934 transmission scan total 8 (black-and-white)935 universal transmission scan total (color)936 universal transmission scan total (black-and-white)937 box scan (color)938 box scan (black-and-white)939 remote scan (color)940 remote scan (black-and-white) Yes941 transmission scan/fax (color)942 transmission scan/fax (black-and-white)943 transmission scan/i-fax (color)944 transmission scan/i-fax (black-and-white)945 transmission scan/e-mail (color)946 transmission scan/e-mail (black-and-white)947 transmission scan/FTP (color)948 transmission scan/FTP (black-and-white)949 transmission scan/SMB (color)950 transmission scan/SMB (black-and-white)951 transmission scan/IPX (color)952 transmission scan/IPX (black-and-white)953 transmission scan/database (black-and-white)954 transmission scan/database (color)955 transmission scan/local print (color)956 transmission scan/local print (black-and-white)957 transmission scan/box (color)
COPIER > COUNTERNo. Description Level
Chapter 17
17-55
<CST>
T-17-54
<ACC>
T-17-55
<INT-FACE>
958 transmission scan/box (black-and-white)
COPIER > OPTION > CSTSub-item Description LevelP-SZ-C1 Use it to set the paper size (right deck).
setting: 6: A4 (default); 15: B5; 18: LTR 1
P-SZ-C2 Use it to set the paper size (left deck).setting: 6: A4 (default); 15: B5; 18: LTR 1
U1-NAMEto U4-NAME
Use it to enable/disable display of a paper name when a size from a specific paper size group (U1 to U4) is detected.setting0: on the touch panel, indicate U1, U2, U3, U4 (default)1: indicate paper name selected in service mode: CST-U1, U2, U3, U4
2
CST-U1/U2/U3/U4
Use it to select paper names used in paper size groups.By setting any of the following special paper sizes for U1, U2, U3, and U4, these paper sizes may be recognized as special size papers for the universal cassette in question.setting24: Foolscap (CST-U2; default)25: Australian Foolscap26: Oficio27: Ecuadorian Officio28: Bolivian Officio29: Argentine Letter (U4; default)30: Argentine Letter-R31: Government Letter (U1; default)32: Government Letter (U1; default)32: Government Letter-R34: Government Legal (U3; default)35: Folio36: Argentine Officio37: Mexico Officio38: Executive
2
COPIER > OPTION > ACCSub-item Description LevelCOIN Use it to set the coin vendor mechanism.
setting0: off1: on
1
DK-P Use it to set the size of paper used in the Side Paper Deck.(for the Side Paper Deck AD1)setting0: A4 (default)1: B52: LTR
1
CCV2CT Use it to enable/disable large 2 count control.0: off (disable 2-count control; default)1: on (enable 2-count control; count pulse width/pulse width, 100 msec)2: on (enable 2-count control; count pulse width/pulse width, 30 msec)
1
CCV-LSZ Use it to set a threshold for small/large size identification used in large 2 count mode.setting: 0 to 458 (default: 364; in mm) 1
PD-SIZE Setting size of the Side Paper Deck AE1 (displayed only the Side Paper Deck AE1 is mounted) Normal size can be set with the user mode, and special size can be set with the service mode. Setting Range: 0 to 37 [default: 0] The value 0 or 22 to 37 can be set with the service mode. If the setting value is 0 to 21, the value 1 to 21 can be input with the user mode.
1
CC-SPSW Use it to set control card I/F support.0: do not support (default)1: support
2
COPIER > COUNTERNo. Description Level
Chapter 17
17-56
T-17-56
<TEMPO>
T-17-57
<LCNS-TR>
T-17-58
COPIER > OPTION > INT-FACESub-item Description LevelIMG-CONT Use it to set the connection of the EFI controller.
setting0: no controller1: EFI model (PINATUBO, Mt. Hood)2: T/R, AHT model3: EFI external controller present (Yukon/Pinatubo V2.0)4: EFI external controller present (Meru V3.1)
1
AP-OPT Use it to permit/not permit printing from application PrintMe built into the PS print server unit.setting0: permit printing using unspecific ID (default)1: permit printing using specific account2: reject printing
2
AP-ACCNT Use it to set (CPCA) group ID for printing (job) from application PrintMe built into the PS print server unit.setting0 to 9999999 (default: 0)
2
AP-CODE Use it to set the (CPCA) path for printing (job) from application PrintMe built into the PS print server unit.setting0 to 99999999 (default: 0)
2
COPIER > OPTION > TEMPOSub-item Description LevelF-POT-SW Use it to enable/disable settings in the event of a transfer fault caused by a fault in the potential sensor.
- Use it as a tentative remedy until the potential sensor is replaced.settling0: off (default); 1: on
2
F-POT-D Use it to make settings in relation to transfer faults caused by a fault in the potential sensor.- The setting will be valid only when F-POT-SW is set to '1'.- The degree of separation current may be 0>1>2.setting0: if user tends to use originals with low image ratio (text original )1: if user tends to use originals with high image ratio (photo original)2: do not use normally; however, use if double transfer occurs (dropout at about 50 mm of leading edge)
2
F-HUM-SW Use it to enable/disable F-HUM-D settings in the event of a fault in the environment sensor.- Use it as a tentative remedy until the environment sensor is replaced.setting0: off (default); 1: on (enable F-HUM-D setting)
2
F-HUM-D Use it to manually set the humidity for the site of installation.- The machine assumes it as the output of the humidity sensor.- The setting will be valid only when F-HUM-SW is '1'.setting: 30 to 99 (default: 35(%))
2
COPIER > OPTION > LCNS-TR Sub-item Description LevelEX: ST-XXXX 1 ( ) {0 to 0} [1] [2] [1]: for state indication, 0: not installed (default); 1: installed[2]: for invalidation execution, 0: execute (input accepted only if '0')Procedure (invalidation of transfer)1) Select SET-XXXX, and type in '0'; then, press the OK key.2) See that a transfer license number (24 characters) is indicated for TR-XXXX.
ST-SEND Use it to display the installation state/invalidate transfer of the SEND function as part of transfer invalidation.2
TR-SEND Use it to obtain a transfer license key for the SEND function as part of transfer invalidation. 2
ST-ENPDF Use it to display the installation state/to execute transfer invalidation of the SEND encryption PDF transmission function as part of transfer invalidation. 2
TR-ENPDF Use it to obtain a transfer license key for the SEND encryption PDF transmission function as part of transfer invalidation.2
ST-SPDF Use it to display the installation state/to execute transfer invalidation of the SEND searchable PDF transmission function as part of transfer invalidation. 2
Chapter 17
17-57
TR-SPDF Use it to obtain a transfer license key for the SEND searchable PDF transmission function as part of transfer invalidation.2
ST-EXPDF Use it to display the installation state/to execute transfer invalidation of the PDF expansion (composite function of encryption PDF + searchable PDF) as part of transfer invalidation. 2
TR-EXPDF Use it to obtain a transfer license key for the PDF expansion kit (composite function of encryption PDF + searchable PDF) as part of transfer invalidation. 2
ST-PDFDR Use it to display the installation state/to execute transfer invalidation of the PDF direct transmission mechanism as part of transfer invalidation. 2
TR-PDFDR Use it to obtain a transfer license key as part of transfer invalidation. 2
ST-SCR Use it to display the installation sate/execute transfer invalidation of the encryption secured printing function as part of transfer invalidation. 2
TR-SCR Use it to obtain a transfer license key for the encryption secured printing as part of transfer invalidation. 2
ST-CHSNG Not used 2
TR-CHSNG Not used 2
ST-BRDIM Use it to display/execute transfer invalidation of Bar DIMM as part of transfer invalidation. 2
TR-BRDIM Use it to obtain a transfer license key for bar DIMM as part of transfer invalidation. 2
ST-VNC Use it to display the installation state/to execute transfer invalidation for VNC as part of transfer invalidation.2
TR-VNC Use it to obtain a transfer license key for VNC as part of transfer invalidation. 2
ST-WEB Use it to display the installation sate/execute transfer invalidation for a WEB browser as part of transfer invalidation.2
TR-WEB Use it to obtain a transfer license key for a WEB browser as part of transfer invalidation. 2
ST-WTMRK Display the installation status of the tint block printing function in transfer invalidation. / Execute transfer invalidation.2
TR-WTMRK Obtain a transfer license key for the tint block printing function in transfer invalidation.2
ST-TSPDF Display the installation status of the PDF send function with a time stamp in transfer invalidation.2
TR-TSPDF Obtain a transfer license key for the PDF send function with a time stamp in transfer invalidation.2
ST-USPDF Display the installation status of the PDF send function with a user signature in transfer invalidation.2
TR-USPDF Obtain a transfer license key for the PDF send function with a user signature in transfer invalidation.2
ST-DVPDF Display the installation status of the PDF send function with a device signature in transfer invalidation.2
TR-DVPDF Obtain a transfer license key for the PDF send function with a device signature in transfer invalidation.2
ST-SCPDF Display the installation status of the scalable PDF send function in transfer invalidation.2
TR-SCPDF Obtain a transfer license key for the scalable PDF send function in transfer invalidation.2
ST-AMS Display the installation status of ACQ in transfer invalidation.2
TR-AMS Obtain a transfer license key for ACQ in transfer invalidation.2
ST-ERDS Display the installation status of the ERDS 3rd party advanced function in transfer invalidation.2
TR-ERDS Obtain a transfer license key for the ERDS 3rd party advanced function in transfer invalidation.2
ST-PS Display the installation status of PS in transfer invalidation.2
TR-PS Obtain a transfer license key for PS in transfer invalidation.2
ST-PCL Display the installation status of PCL in transfer invalidation.2
TR-PCL Obtain a transfer license key for PCL in transfer invalidation.2
COPIER > OPTION > LCNS-TR Sub-item Description Level
Chapter 17
17-58
17.6.2 FEEDER
17.6.2.1 FEEDER List0015-6262
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-59
17.6.3 SORTER
17.6.3.1 SORTER List0015-6269
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
ST-PSLI5 Display the installation status of PS, LIPS4, and LIPS LX in transfer invalidation.2
TR-PSLI5 Obtain a transfer license key for PS, LIPS4, and LIPS LX in transfer invalidation.2
ST-LIPS5 Display the installation status of LIPS LX and LIPS4 in transfer invalidation.2
TR-LIPS5 Obtain a transfer license key for LIPS LX and LIPS4 in transfer invalidation.2
ST-LIPS4 Display the installation status of LIPS4 in transfer invalidation.2
TR-LIPS4 Obtain a transfer license key for LIPS4 in transfer invalidation.2
ST-PSPCL Display the installation status of PS and PCL in transfer invalidation.2
TR-PSPCL Obtain a transfer license key for PS and PCL in transfer invalidation.2
ST-PCLUF Display the installation status of PCL and UFR in transfer invalidation.2
TR-PCLUF Obtain a transfer license key for PCL and UFR in transfer invalidation.2
ST-PSLIP Display the installation status of PS and LIPS in transfer invalidation.2
TR-PSLIP Obtain a transfer license key for PS and LIPS in transfer invalidation.2
ST-PSPCU Display the installation status of PS, PCL, and UFR in transfer invalidation.2
TR-PSPCU Obtain a transfer license key for PS, PCL, and UFR in transfer invalidation.2
ST-LXUFR Display the installation status of LIPS LX (UFR II for overseas) in transfer invalidation.2
TR-LXUFR Obtain a transfer license key for LIPS LX (UFR II for overseas) in transfer invalidation.2
ST-HDCR2 Display the installation status of complete HDD deletion in transfer invalidation.2
TR-HDCR2 Obtain a transfer license key for complete HDD deletion in transfer invalidation.2
COPIER > FEEDER > OPTION Sub-item Description LevelSIZE-SW Use it to enable detection of a mix of AB and inch originals.
setting0: ON (do not detect; default); 1: OFF (detect)
1
LS-DBL Use it to enable/disable ADF high-speed duplex mode.setting0: enable (execute high-speed duplex mode; normal mode; default)1: disable (do not execute high-speed duplex mode; low-speed duplex mode)
1
STAMP-SW Use it to indicate the presence/absence of a stamp. (If fitted, set '1' for STAMP-SW).setting0: stamp absent1: stamp present (default)
1
COPIER > OPTION > LCNS-TR Sub-item Description Level
Chapter 17
17-59
T-17-60
17.6.4 BOARD
17.6.4.1 BOARD List0015-6272
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-17-61
17.7 TEST (Test Print Mode)
17.7.1 COPIER
17.7.1.1 COPIER List0015-5967
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<PG>T-17-62
COPIER > SORTER > OPTIONSub-item Description LevelBLNK-SW Use it to set the margin width on both sides of a crease when the saddle stitcher is in use.
setting0: normal width (5 mm)1: extra width (10 mm; default)
1
MD-SPRTN Use it to enable/disable accessory-independent mode in the event of a finisher error.setting0: normal (disable accessory-independent mode; default)1: enable (do not staple or align)
1
COPIER > BOARD > OPTIONSub-item Description LevelFONTDL Use it to enable/disable display of the setting screen for font service when the PS kanji font downloaded is in use.
setting0: disable (do not display; default)1: enable (display)
1
MENU-1 to 4 Use it to enable/disable display of levels 1 thorough 4 for the printer settings menu.setting0: disable (do not display; default)1: enable (display)
2
COPIER > TEST > PGSub-item Description LevelTYPE Enter the type No. of the desired test print, and press the Start key to print out a test print. (Be sure to return it to '0' after printing.)
0: image from CCD (normal print)1: grid2: 17 gradations (error diffusion; T-BIC)3: 17 gradations (dither screen)4: blank 00H5: halftone 80 H (error diffusion; T-BIC)6: halftone 80 H (dither screen)7: solid black FFH8: horizontal line (space: 27 dots; line width: 4 dots)9: horizontal line (space: 50 dots; line width: 6 dots)10: horizontal line (space: 3 dots; line width: 2 dots)11: halftone 60H (error diffusion; T-BIC)12: halftone 60H (dither screen)13: halftone 30H (error diffusion: T-BIC)14: halftone 30H (dither screen)15: 17 gradations (text mode)16: 17 gradations (text/photo mode)17: 17 gradations (print photo mode)18: 17 gradations (film photo mode)19: for R&D20: 17 gradations (PDL screen: medium resolution)21: 17 gradations (PDL screen: low resolution)22: 17 gradations (PDL screen: high resolution)23 to 30: for R&D
1
TXPH Use it to switch between text mode or photo mode for test printing.
1setting: 0 to 4
Chapter 17
17-60
<NETWORK>T-17-63
1) Hold down the control panel switch to start shut-down sequence. When ready, turn off the main power switch.2) Connect the network cable to the machine, and turn on the main power switch.3) Inform the user's system administrator that the installation of the machine is over, and ask him/her to make network settings.4) Inform the system administrator that you are going to check the network connection, and find out the remote host address (i.e., the IP address of a PC terminalon the user's network).5) Make the following selections in service mode: COPIER>TEST>NETWORK>PING; then, type in the IP address you obtained in step 4) When ready, press theOK key and then the Start key.- The indication will be 'OK' if the connection to the network is correct. (End the work.)- If the indication is 'NG', on the other hand, check the connection of the network cable; if the cable is normal, go to step 6). If a fault is found in the cable, correctit, and go back to step 5).6) Make the following selections in service mode: COPIES>TEST>NETWORK>PING. Then, enter the local host address (i.e., IP address of the machine), andpress the OK key.- If the indication is 'NG', suspect a fault in the IP address of the machine or of the network controller. Ask the system administrator for a check on the IP address,or replace the main controller PCB.- If the indication is 'OK', on the other hand, the network settings and the network controller may be assumed to be normal. If so, suspect a fault in the user's networkenvironment; report to the system administrator for remedial work.7) Make the following selections in service mode: COPIER>TEST>NETWORK>PING; then, enter the local host address (i.e., IP address of the machine), andpress the OK key.- If the notation is 'NG', suspect a fault in the IP address of the machine or in the network controller. Contact the system administrator to obtain the correct IP addressor replace the main controller PCB.- If the notation is 'OK', the network settings and the network controller may be assumed to be free of faults. The fault is likely to be in the user's network environ-ment. Contact the system administrator for remedial action.
F-17-15
17.8 COUNTER (Counter Mode)
17.8.1 COPIER
17.8.1.1 COPIER List0015-5953
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<TOTAL>
PG-PICK Use it to select the source of paper for test printing.1: right deck2: left deck3: cassette 34: cassette 45-6: not used7: side deck8: multifeeder
1
2-SIDE Use it to select the output mode for test printing.setting0: simplex1: duplex(at time of shipment/upon RAM initialization: 0)
1
PG-QTY Use it to select the output mode for test printing.Use it to set a copy count for test printing.1 to 999 (default: 1)
1
COPIER > TEST > NETWORK Sub-item Description LevelPING Use it to check the connection between the machine and a network (only if TCP/IP).
Use it when checking the connection at time of installation or in the event of a network connection fault.1
COPIER > TEST > PGSub-item Description Level
Result (OK/NG) IP address input
Chapter 17
17-61
T-17-64
<PICKUP>T-17-65
COPIER > COUNTER > TOTALSub-item Description LevelSERVICE1 total counter 1 for service
Increases the count when paper is discharged outside the machine.(regardless of the size of paper, i.e., large or small)after 99999999, resets to 00000000
1
SERVICE2 total counter 2 for serviceIncreases the count when paper is discharge outside the machine.(in the case of large size, increases by 2; in the case of small size, increases by 1)after 99999999, resets to 00000000
1
COPY total copy counterIncreases the count when copying is over and the paper is discharged outside the machine.after 99999999, resets to 00000000
1
PDL-PRT PDL print counterIncreases the count when paper is discharged outside the machine or duplex stacking occurs to suit the charge counter in PDL print mode.in the case of a blank sheet, the count remains unchanged; for both large and small sizes, the count is increased by 1after 99999999, resets to 00000000
1
FAX-PRT fax reception print counterIncreases the count when paper is discharged outside the machine or duplex stacking occurs to suit the charge counter in fax reception mode.in the case of a blank sheet, the count remains unchanged; for both large and small sizes, the count is increased by 1; the reading may be resetafter 99999999, resets to 00000000
1
RMT-PRT remote print counterIncreases the count when paper is discharged outside the machine or duplex stacking occurs to suit the charge counter in remote print mode.in the case of a blank sheet, the count remains unchanged: for both large and small sizes, the count is increased by 1; the reading may be resetafter 99999999, resets to 00000000
1
BOX-PRT box print counterIncrease the count when paper is discharged outside the machine or duplex stacking occurs to suit the charge counter in box print mode.in the case of a blank sheet, the count remains unchanged; for both large and small sizes, the count is increased by 1; the reading may be resetafter 99999999, resets to 00000000
1
RPT-PRT report print counterIncreases the count when paper is discharged outside the machine or duplex stacking occurs to suit the charge counter in report print mode.in the case of a blank sheet, the count remains unchanged; for both large and small sizes, the count is increased by 1; the reading may be resetafter 99999999, resets to 00000000
1
2-SIDE duplex copy/print counterIncreases the count when paper is discharged outside the machine or when duplex stacking occurs to suit the charge counter and to indicate the number of duplex copies/prints.in the case of a blank sheet, the count remains unchanged; for both large and small sizes, the count is increases by 1; the reading may be resetafter 99999999, reset to 00000000
1
SCAN scan counterIncreases the count when an original has been read, indicating the number of originals read.for both large and small sizes, the count is increased by 1; the reading may be resetafter 99999999, resets to 00000000
1
COPIER > COUNTER > PICKUPSub-item Description LevelC1/2/3/4 cassette 1/2/3/4 pickup total counter
Indicates the number of sheets picked up from the cassette 1 (right deck)/2 (left deck)/3/4.after 99999999, resets to 00000000
1
MF manual feeder pickup total counterIndicates the number of sheets picked up from the manual feed pickup unit.after 99999999, resets to 00000000
1
DK deck pickup total counterIndicates the number of sheets picked up from the deck pickup unit.after 99999999, resets to 00000000
1
Chapter 17
17-62
<FEEDER>T-17-66
<JAM>T-17-67
<MISC>T-17-68
<PRDC-1>T-17-69
<DRBL-1>T-17-70
2-SIDE duplex pickup total counterIndicates the number of sheets picked up for duplexing.after 99999999, resets to 00000000.
1
COPIER > COUNTER > FEEDERSub-item Description LevelFEED ADF original pick total counter 1DFOP-CNT Indicates the number of times the ADF hinge has opened/closed.
setting0: OFF (default)00000000 to 99999999
1
COPIER > COUNTER > JAMSub-item Description LevelTOTAL total jam counter 1FEEDER feeder total jam counter 1SORTER finisher total jam counter 12-SIDE duplexing unit jam counter 1MF manual feed pickup jam counter 1C1/2/3/4 right deck/left deck/cassette 3/cassette 4 jam counter 1DK side paper deck jam counter 1
COPIER > COUNTER > MISCSub-item Description LevelFIX-WEB fixing web counter (Be sure to reset the counter when the fixing web has been replaced.) 1WST-TNR collecting toner counter (Be sure to reset the counter when collecting toner has been disposed of.) 1
COPIER > COUNTER > PRDC-1Sub-item Description LevelPRM-WIRE primary charging wire counter 1PRM-GRID primary grid wire counter 1PO-WIRE pre-transfer charging wire counter 1TR-WIRE transfer charging wire counter 1SP-WIRE separation charging wire counter 1PRM-CLN primary charging wire cleaner counter 1TR-CLN transfer charging wire cleaner counter 1PO-CLN pre-transfer charging wire cleaner counter 1SP-CLN separation charging wire cleaner counter 1TR-CLN2 transfer charging wire cleaner 2 counter 1FIX-TH1 fixing main thermistor (THM1) counter 1FIX-TH2 fixing sub thermistor (THM2) counter 1OZ-FIL1 ozone filter 1AR-FIL1 air filter 1 1AR-FIL2 air filter 2 1
COPIER > COUNTER > DRBL-1Sub-item Description LevelPRM-UNIT primary charging assembly counter 1PO-UNIT pre-transfer charging assembly counter 1PO-SCRPR pre-transfer charging assembly scraper counter 1T/S-UNIT transfer/separation charging assembly counter 1CLN-BLD cleaner blade counter 1SP-CLAW cleaner separation claw counter 1DVG-CYL developing cylinder counter 1
COPIER > COUNTER > PICKUPSub-item Description Level
Chapter 17
17-63
<DRBL-2>T-17-71
DVG-ROLL developing spacer counter 1C3-PU-RL cassette 3 pickup roller counter 1C3-SP-RL cassette 3 separation roller counter 1C3-FD-RL cassette 3 feed roller counter 1C4-PU-RL cassette 4 pickup roller counter 1C4-SP-RL cassette 4 separation roller counter 1C4-FD-RL cassette 4 feed roller counter 1LD-PU-RL left front deck pickup roller counter 1LD-SP-RL left front deck separation roller counter 1LD-FD-RL left front deck feed roller counter 1RD-SP-RL right front deck separation roller counter 1RD-FD-RL right front deck feed roller counter 1RD-PU-RL right front deck pickup roller counter 1M-SP-RL manual feed tray separation roller counter 1M-FD-RL manual feed tray feed roller counter 1FX-UP-RL fixing roller counter 1FX-LW-RL pressure roller counter 1FX-IN-BS fixing heat insulating bush counter 1FX-WEB Indicates the number of times the fixing web has been taken up.
If you have replaced the web, be sure to reset the reading in service mode: COPIER>COUNTER>MISC>FIX-WEB, COPIER>COUNTER>DRBL-1>FX-WEB. 1
DLV-UCLW delivery upper separation claw counter 1DLV-LCLW delivery lower separation claw counter 1
COPIER > COUNTER > DRBL-2Sub-item Description LevelDF-PU-RL Indicates the number of sheets picked up by the ADF pickup roller.
(counter reading retained by the controller PCB)for both simplex and duplex modes, the count is increased by 1 (regardless of the number of sides); also, there is no distinction between large and small sizes
1
DF-SP-PL Indicates the number of sheets separated by the ADF separation pad.setting rage/setting item00000000 to 99999999
1
DF-SP-PD Indicates the number of sheets separated by the ADF separation pad.(counter reading retained by the controller PCB)for both simplex and duplex modes, the count is increase by 1 (regardless of the number of sides); also, there is no distinction between large and small sizes
1
DF-FD-RL Indicates the number of sheets feeded by the ADF feed roller.(counter reading retained by the controller PCB)in the case of simplex mode, the count is increased by 1 for each original read; in the case of duplex mode, the count is increased by 3 for each original read (to accommodate 3 feeding sessions, i.e., face, back, and idle); there is no distinction between large and small sizes
1
LNT-TAP1 Indicates the number of sheets moving past the ADF dust-collecting tape.for both simplex and duplex modes, the count is increased by 1 for each original read (not its sides) 1
LNT-TAP2 Indicates the number of sheets moving past the ADF dust-collecting tape.for both simplex and duplex modes, the count is increased by 1 for each original read (not its sides) 1
LNT-TAP3 Indicates the number of sheets moving past the ADF dust-collecting tape.for both simplex and duplex modes, the count is increased by 1 for each original read (not its sides) 1
LNT-TAP4 Indicates the number of sheets moving past the ADF dust-collecting tape.for both simplex and duplex modes, the count is increased by 1 for each original read (not its sides) 1
LNT-TAP5 Indicates the number of sheets moving past the ADF dust-collecting tape.for both simplex and duplex modes, the count is increased by 1 for each original read (not its sides) 1
STAMP number of times the stamp solenoid has gone on 1
PD-PU-RL Indicates the number of sheets moving past the paper deck pickup roller.(counter reading retained by the controller PCB) 1
COPIER > COUNTER > DRBL-1Sub-item Description Level
Chapter 17
17-64
PD-SP-RL Indicates the number of sheets moving past the paper deck separation roller.(counter reading retained by the controller PCB) 1
PD-FD-RL Indicates the number of sheets moving past the controller PCB.(counter reading retained by the controller PCB) 1
SORT Sort counterThe large and small sizes are not distinguished from each other. 1
FIN-STPR stapler (handling tray assembly) 1SADDLE Saddle paper transport counter
The large and small sizes are not distinguished from each other. 1
SDL-STPL Indicates the number of times the stapler (saddle assembly) has operated.(counter reading retained by the DC controller PCB) 1
PUNCH Punching counter 1
FIN-BFFRL Indicates the number of times the puncher has swung. 1
COPIER > COUNTER > DRBL-2Sub-item Description Level
Chapter 18 Upgrading
Contents
Contents
18.1 Outline........................................................................................................................................................................18-118.1.1 Outline of Upgrading the Machine .......................................................................................................................................... 18-118.1.2 Outline of the Service Support Tool ....................................................................................................................................... 18-1
18.2 Making Preparations ..................................................................................................................................................18-418.2.1 Registering the System Software ............................................................................................................................................. 18-418.2.2 Making Connections ................................................................................................................................................................ 18-6
18.3 Formatting the HDD ..................................................................................................................................................18-818.3.1 Formatting All Partitions ......................................................................................................................................................... 18-818.3.2 Formatting Selected Partitions ................................................................................................................................................. 18-918.3.3 Formatting the Partitions.......................................................................................................................................................... 18-9
18.4 Downloading System Software................................................................................................................................18-1118.4.1 Downloading System ............................................................................................................................................................. 18-11
18.4.1.1 Outline.......................................................................................................................................................................................................18-1118.4.1.2 Downloading Procedure............................................................................................................................................................................18-11
18.4.2 Downloading RUI, and Language ......................................................................................................................................... 18-1318.4.2.1 Outline.......................................................................................................................................................................................................18-1318.4.2.2 Downloading Procedure............................................................................................................................................................................18-15
18.4.3 Downloading SDICT ............................................................................................................................................................. 18-1618.4.3.1 Outline.......................................................................................................................................................................................................18-1618.4.3.2 Downloading Procedure............................................................................................................................................................................18-16
18.4.4 Downloading MEAPCONT................................................................................................................................................... 18-1818.4.4.1 Outline.......................................................................................................................................................................................................18-1818.4.4.2 Downloading Procedure............................................................................................................................................................................18-18
18.4.5 Downloading KEY................................................................................................................................................................. 18-1918.4.5.1 Outline.......................................................................................................................................................................................................18-1918.4.5.2 Downloading Procedure............................................................................................................................................................................18-20
18.4.6 Downloading the TTS............................................................................................................................................................ 18-2118.4.6.1 Outline.......................................................................................................................................................................................................18-2118.4.6.2 Downloading Procedure............................................................................................................................................................................18-21
18.4.7 Downloading BOOT.............................................................................................................................................................. 18-2218.4.7.1 Outline.......................................................................................................................................................................................................18-2218.4.7.2 Downloading Procedure............................................................................................................................................................................18-23
18.4.8 Downloading Dcon and Rcon................................................................................................................................................ 18-2418.4.8.1 Outline.......................................................................................................................................................................................................18-2418.4.8.2 Downloading Procedure............................................................................................................................................................................18-25
18.4.9 Downloading G3 FAX........................................................................................................................................................... 18-2618.4.9.1 Outline.......................................................................................................................................................................................................18-2618.4.9.2 Downloading Procedure............................................................................................................................................................................18-27
18.4.10 Uploading and Downloading Backup Data ......................................................................................................................... 18-2818.4.10.1 Outline.....................................................................................................................................................................................................18-2818.4.10.2 Uploading Procedure...............................................................................................................................................................................18-2918.4.10.3 Downloading Procedure..........................................................................................................................................................................18-31
Chapter 18
18-1
18.1 Outline
18.1.1 Outline of Upgrading the Machine0015-5401
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The machine and its accessories may be upgraded by replacing DIMM-ROM or using the Service Support Tool (hereafter, SST) installed on a personal computer(PC).The following table shows the various system software used in conjunction with the machine and how they may be upgraded.
T-18-1
18.1.2 Outline of the Service Support Tool0015-5402
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The Service Support Tool (hereafter, SST) has the following functions:
F-18-1The machine must be in download mode when the SST is used.
Type Type of system software Method of upgrading Remarks
SST ROM-DIMM replacement
Machine
System (main controller) Yes No The machine controller is also used to control the Super G3 Fax Board.
Language (language mode) Yes No
RUI (remote user interface) Yes No
Boot (boot program) Yes Yes
MEAP CONT (MEAP library) Yes No
SDICT (OCR dictionary) Yes No
KEY (encryption communication key) Yes No
TTS (voice dictionary) Yes No
DCON (DC controller) Yes No
RCON (reader controller) Yes No The reader controller is also used to control the ADF.
Accessory
Multi-FAX Board Yes Yes
Fin_A series (Finisher-AD1/Saddle Finisher-AE2)
Yes No A special service tool (downloader PCB: FY9-2034) is needed.
DADF-S1 YesVer.3.3 or later
No A special service tool (downloader PCB: FY9-2034) is needed.
Initialize HDD
Download system software
Upload backup data
Download backup data Backup data
System software
HDD setting information
SST
HDD
Flash ROM
Back up RAM
Service PC
iR ----
Chapter 18
18-2
The download control program comes in 2 types:
-Normal Mode (download mode B)turn on the main power while holding down 1+7; then, make the following selections in service mode: COPIER>FUNCTION>SYSTEM>DOWNLOAD-Safe Mode(download mode A)turn on the main power while holding down 2+8
F-18-2
Use safe mode for the following:- when you have replaced the HDD.- when the system fails to start up normally.
The following table shows the functions that may be used in download mode with the SST in use:T-18-2
Function Download mode
Normal mode(download mode B)
Safe mode(download mode A)
Formatting the HDD --
Entire HDDBOOTDEV
FSTDEVTMP_GENTMP_PSSTMP_FAXAPL_SENDAPL_MEAPAPL_GENPDL_DEVFSTCDEV
---------
Main power switch ON
on keypad, 2+8 on keypad, 1+7
Boot ROMSafe modeprogram
Boot program
Download mode A Download mode B
HDD
COPIER > FUNCTION >SYSTEM > DOWNLOAD
SYSTEM program
In service mode
normal modeprogram
Chapter 18
18-3
Installing the System SoftwareThe system software that has been downloaded by the SST (version 3.33 or later) is saved in the temporary storage area of the HDD. You must then turn off andthen on the main power switch so that the system software will be written to the system area and flash ROM when the machine starts up. When you turn off andthen on the main power switch for a second time, the machine will start up using the new version of the system software.
F-18-3
If a previous version of the SST is used for downloading, the system software will be written directly to the HDD, boot ROM, and flash ROM.The previous version of the SST is not enable to use for this model.
Downloading the system software -System-Language-RUI-Boot-G3FAX-Dcon-Rcon-SDICT-MEAPCONT-KEY-TTS
-System-Language-RUI-Boot--Dcon-Rcon-SDICT-MEAPCONT-KEY-TTS
Uploading/downloading backup data
--
-SramImg-Meapback
Function Download mode
Normal mode(download mode B)
Safe mode(download mode A)
Boot ROM
FLASH ROM
HDD
SystemSoftware
SystemSoftware
- - - Download Mode - - -- - - Download Mode - - -[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%
<<<<< download shell >>>>><<<<< download shell >>>>>[ SYSTEM JPja-m ] - - - -[ SYSTEM JPja-m ] - - - -[ SYSTEM ZZ ] - - - - - - -[ SYSTEM ZZ ] - - - - - - -[ SYSTEM JPja-w ] - - - -[ SYSTEM JPja-w ] - - - -[ SYSTEM ZZ ] - - - - - - -[ SYSTEM ZZ ] - - - - - - -[ FONT F ] - - - - - - - - - -[ FONT F ] - - - - - - - - - -[ FONT G ] - - - - - - - - - -[ FONT G ] - - - - - - - - - -+++ Switch OFF the power then ON. ++++++ Switch OFF the power then ON. +++
Upgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading completeUpgrading complete
- - - Download Mode - - -- - - Download Mode - - -[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -[ iR2270iM-ZZjaxxxx-49AD.PRG ] - - - - - - -[ iR2270iM-ZZjaxxxx-49AD.PRG ] - - - - - - -[ iR2270iW-JPjaxxxx-5C16-MN.PRG ] - - - -[ iR2270iW-JPjaxxxx-5C16-MN.PRG ] - - - -[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -[ iR2270iF-JPjaxxxx-DE96-ICC.PRG ] - - - -[ iR2270iF-JPjaxxxx-DE96-ICC.PRG ] - - - -[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -[ iR2270iG-JPjaxxxx-EC30-ICC.PRG ] - - - -[ iR2270iG-JPjaxxxx-EC30-ICC.PRG ] - - - -
CompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteComplete
Temporary storage area
HDD
SystemSoftware
System area
Status of reception (sample)
The main power switch is turned off and then on.
The machine starts up using the new version.
2)
The main motor switch is turned off and then on.
4)
5)
The system software is downloaded.1)
Writing takes place.3)
Temporary storage area
Chapter 18
18-4
F-18-4
18.2 Making Preparations
18.2.1 Registering the System Software0015-5404
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You must first register the system software found on the System CD to the SST.
[Preparatory Work]Items to Prepare-PC to which the SST (version 3.33 or later) has been installed-System CD for the iR5075/5065/5055 Series
[Registering the System Software]1) Start up the PC.2) Set the system CD in the PC.3) Start up the SST.4) Click [Register System Software]
F-18-55) Select the drive in which you have set the System CD, and click [SEARCH].
HDD
Boot ROM
Flash ROM
SystemSoftware
Chapter 18
18-5
F-18-66) The list of system software found on the System CD appears. Remove the check from the folders and software you will not need; then, click [REGISTER].
F-18-77) When the result of registration is indicated, click [OK].
Chapter 18
18-6
F-18-8
18.2.2 Making Connections0015-5405
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You are now ready to connect the PC to the machine.
[Preparatory Work]Items to Prepare- PC to which the SST (version 3.33 or later) and the system software for the iR5075/5065/5055 series has been registered- Twisted pair cross cable10Base-T: Category 3 or 5100Base-TX: Category 5
[Procedure]1) Start up the PC.2) Check the network settings of the PC.- At the command prompt, type 'IPCONFIG', and press the Return key.- Check to see that the network settings are as follows:IP address: 172.16.1.160subnet mask: 255.255.255.0default gateway: any
Do not use the following IP address:- 172.16.1.0- 172.16.1.100- 172.16.1.255If the settings are not as indicated below, make the appropriate changes:
F-18-9
C:\
W i n d ow s 2 0 0 0 I P C o n f i g u r a t i o n
M i c r o s o f t W i n d ow s 2 0 0 0 [ Ve r s i o n 5 . 0 0 . 2 1 9 5 ]( C ) C o py r i g h t 1 9 8 5 - 1 9 9 9 M i n c r o s o f t C o r p.
E t h e r n e t a d a p t e r L o c a l A r e a C o n n e c t i o n :
C o n n e c t i o n - s p e c i f i c D N S S u f f i x . :I P A d d r e s s . . . . . . . . . . . . : 1 7 2 . 1 6 . 1 . 1 6 0S u b n e t M a s k . . . . . . . . . . . : 2 5 5 . 2 5 5 . 2 5 5 . 0D e fa u l t G a t eway . . . . . . . . . :
C : \
C : \ i p c o n f i g
Command Prompt
Chapter 18
18-7
3) Check to see that the Execute/Memory lamp on the control panel is off, and turn off the main power switch.3-1) Hold down the power switch on the control panel for 3 sec or more.3-2) Follow the instructions indicated on the control panel so that the main power switch may be turned off.3-3) Turn off the main power switch.4) Connect the PC to the machine using a cross cable.
F-18-105) Start up the machine to suit the download mode you will be using.
- Normal ModeTurn on the main power switch while holding down 1+7.When the machine has started up, make the following selections: COPIER > FUNCTION > SYSTEM > DOWNLOAD.- Safe ModeTurn on the main power switch while holding down 2+8.
6) Start up the Service Support Tool.7) Select the model of the machine to connect.
F-18-118) Click [START].
IP address: 172.16.1.100Subnet mask: 255.255.255.0
IP sddress: 172.16.1.160Subnet mask: 255.255.255.0
Cross cable10Base-T: category 3 or 5100Base-TX: category 5
Chapter 18
18-8
F-18-12
18.3 Formatting the HDD
18.3.1 Formatting All Partitions0015-5406
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
When you format all partitions of the HDD, all individual partitions will be initialized and made ready for use by the main controller.The information needed for partition settings is stored under HDFormat of the iRXXXX.
F-18-13[1] HDD (service part; without partition setup)
[2] Formatting of all partitions (in safe mode only)[3] HDD after formatting[4] Partition setup information
HDD
[1]
[2]
[3]
TMP_GEN
TMP_PSS
FSTDEV
APL_SEND
APL_MEAP
IMG_MNG
APL_GEN
FSTCDEV
BOOTDEV
PDLDEV
TMP_FAX
Chapter 18
18-9
18.3.2 Formatting Selected Partitions0015-5407
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can also format (initialize) only those partitions that you select.
F-18-14[1] Formatting possible in normal mode
[2] Formatting possible in safe mode (requires downloading of System and RUI after formatting)
1. Unless you have selected 'ALL', you may execute formatting without registering HDFormat.2. An attempt to format after selecting TMP_FAX in the absence of a fax board will cause an error.
18.3.3 Formatting the Partitions0015-5410
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Click [Format HDD].
F-18-152) Select the partitions you want to format. Or, select 'ALL'.
HDD
TMP_GEN
TMP_PSS
FSTDEV
APL_SEND
APL_MEAP
IMG_MNG
APL_GEN
FSTCDEV
BOOTDEV
PDLDEV
TMP_FAX[1]
[2]
Chapter 18
18-10
F-18-163) Click [Start].
4) When the Confirmation screen has appeared, click [Execute Formatting].
F-18-175) When the session has ended, click [OK].
Chapter 18
18-11
F-18-186) Start a download session. Or, turn off and then on the machine to end the work.
If you have formatted all partitions or formatted BOOTDEV, be sure to download System newly. (Otherwise, 'E602' will occur when you turn on the main power.)
18.4 Downloading System Software
18.4.1 Downloading System
18.4.1.1 Outline0015-5411
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The system software comes in 2 types (one for use inside Japan and the other, outside Japan).
Unlike previous iR controllers, however, there is only one type of system software. (Previously, one type supported NetWare while the other did not. There is nowonly one type for the machine supporting NetWare.)
18.4.1.2 Downloading Procedure0015-5412
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can run a downloading session either in normal or safe mode.1) Select the version of the system you want to download.
F-18-192) Click [Start].
Chapter 18
18-12
F-18-203) When the session has ended, click [OK].
F-18-214) If you want to start another downloading session, see the appropriate instructions.5) When you are done with downloading, turn off and then on the main power.
6) See the upgrade status indicated on the control panel. When a message appears asking you to turn off and then on the switch, turn off and then on the mainpower.
Be sure never to turn off the power while the machine is executing a downloading session or writing downloaded software. The ongoing session will be suspendedand the machine may fail to start up.
Chapter 18
18-13
F-18-22
F-18-23If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
18.4.2 Downloading RUI, and Language
18.4.2.1 Outline0015-5413
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<<<<< download shell >>>>>[ SYSTEM JPja-m ] - - - -[ SYSTEM ZZ ] - - - - - - -[ SYSTEM JPja-w ] - - - -[ SYSTEM ZZ ] - - - - - - -
Upgrading completeUpgrading completeUpgrading completeWriting to HDD XX%
Chapter 18
18-14
F-18-24T-18-3
T-18-4
Control Panel LCD Display Language
Check the version of System and Language.
1. If correct, You can switch languages by making the following selections in user mode: common settings>display language change.
2. If not correct, 'E744' will be indicated, and System Language will be used when the main power is turned off and then on.
RUI Display Language
Select using the RUI.You can select a different language for a different PC.
<Language Code> <Language>
de German
en English
fr French
it Italian
ja Japanese
LCD
Network PCLanguage RUI
System
RUI(en)
RUI(it)
RUI(ja)
System Language
Language-XXen
Language-XXit
Language-XXja
RUI-XXen
RUI-XXit
RUI-XXja
Version check
Network
iR -----
Chapter 18
18-15
F-18-25
18.4.2.2 Downloading Procedure0015-5414
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can run a download session in either normal or safe mode.[In the Case of Language]1) Select the version of Language to download.
F-18-262) Click [Start].
Download
iR -----
Language XXen XXja
RUI XXen XXja
SST
Service PC iR -----
Main Controller Unit
HDD
BOOTDEV
Language-XXen
Language-XXja
RUI-XXen
RUI-XXja
Chapter 18
18-16
F-18-273) When the result of the downloading session has appeared, click [OK].
F-18-284) If you want another downloading session, see the appropriate instructions.5) When you are done, turn off and then on the main power.
6) See the status of upgrading indicated on the control panel. When a message appears asking you to turn off and then on the machine, turn off and then on themain power.
Be sure never to turn off the power while the machine is executing a downloading session or writing downloaded software. Otherwise, the ongoing session will besuspended and the machine may fail to start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
18.4.3 Downloading SDICT
18.4.3.1 Outline0015-5415
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
SDICT is a dictionary used when converting image data read by the reader unit into character code (OCR processing). This function is used in conjunction with thePDF Generation Expansion Kit.
18.4.3.2 Downloading Procedure0015-5416
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can run a downloading session in either normal or safe mode.
Chapter 18
18-17
1) Select the version of SDICT to download.
F-18-292) Click [Start].
F-18-303) When the session has ended, click [OK].
Chapter 18
18-18
F-18-314) If you want to run another downloading session, see the appropriate instructions.5) When you are done, turn off and then on the main power.
6) See the status of upgrading indicated on the control panel. When a message appears asking you to turn off and then on the switch, turn off and then on themain power.
Be sure never to turn off the machine while it is executing a downloading session or writing downloaded software. Otherwise, the ongoing session will be suspendedand the machine may fail to start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
18.4.4 Downloading MEAPCONT
18.4.4.1 Outline0015-5417
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
MEAPCONT is a standard library used in conjunction with a MEAP application.
18.4.4.2 Downloading Procedure0015-5418
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can execute a downloading session in either normal or safe mode.1) Select the version of MEAPCONT you want to download.
F-18-322) Click [Start].
Chapter 18
18-19
F-18-333) When the downloading session has ended, click [OK].
F-18-344) If you want to run another downloading session, see the appropriate instructions.5) When you are done, turn off and then on the main power.
6) See the status of upgrading indicated on the control panel. When a message appears asking you to turn off and then on the switch, turn off and then on themain power.
Be sure never to turn off the machine while it is executing a downloading session or writing downloaded software. Otherwise, the ongoing session will be suspendedand the machine may fail to start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
18.4.5 Downloading KEY
18.4.5.1 Outline0015-5420
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
KEY is in common among the models that have the new iR controller, and is registered under "iRXXXX" on the SST.
KEY has 2 types (XXxc and XXxp). Be sure to download both types.
Chapter 18
18-20
18.4.5.2 Downloading Procedure0015-5421
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can execute a download session in either normal or safe mode.1) Select the version of KEY you want to download.
F-18-352) Click [Start].
F-18-363) When the downloading session has ended, click [OK].
Chapter 18
18-21
F-18-374) If you want to execute a different downloading session, see the appropriate instructions.5) When you are done, turn off and then on the main power.
6) See the status of upgrading indicated on the control panel of the machine. When a message appears asking you to turn off and then on the switch, turn off andthen on the main power.
Be sure never to turn off the machine while it is executing a downloading session or writing downloaded system software. Otherwise, the ongoing write operationwill be suspended and the machine may fail to start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
18.4.6 Downloading the TTS
18.4.6.1 Outline0015-5422
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
TTS is voice dictionary data when the voice guidance board is installed.
18.4.6.2 Downloading Procedure0015-5423
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can execute a download session in either normal or safe mode.1) Select the version of TTS you want to download.
F-18-382) Click [Start].
Chapter 18
18-22
F-18-393) When the downloading session has ended, click [OK].
F-18-404) If you want to execute a different downloading session, see the appropriate instructions.5) When you are done, turn off and then on the main power.
6) See the status of upgrading indicated on the control panel of the machine. When a message appears asking you to turn off and then on the switch, turn off andthen on the main power.
Be sure never to turn off the machine while it is executing a downloading session or writing downloaded system software. Otherwise, the ongoing write operationwill be suspended and the machine may fail to start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
18.4.7 Downloading BOOT
18.4.7.1 Outline0015-5424
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Boot registered in the SST may be used in common for various types of boot ROMs. You cannot change the type of a boot ROM by means of downloading.
Chapter 18
18-23
F-18-41
If a downloading session fails, you will have to replace the boot ROM.
18.4.7.2 Downloading Procedure0015-5425
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can execute a downloading session in either normal or safe mode.1) Select the version of BOOT to download.
F-18-422) Click [Start].
PC for service
SST
Boot ROM(Flash ROM DIMM)
iR ----
iR ----
Boot
may be upgraded byDIMM replacement
Download
Main controller block
C Boot ROM(Flash ROM DIMM)
P Boot ROM(Flash ROM DIMM)
N Boot ROM(Flash ROM DIMM)
(100V machine only)
(other than 100V machine)
H Boot ROM(Flash ROM DIMM)
(other than 100V machine)
Chapter 18
18-24
F-18-433) When the downloading session has ended, click [OK].
F-18-444) If you want to execute a different downloading session, see the appropriate instructions.5) When you are done, turn off and then on the main power.
6) See the status of upgrading indicated on the control panel of the machine. When a message appears asking you to turn off and then on the switch, turn off andthen on the main power.
Be sure never to turn off the machine while it is executing a download session or writing downloaded system software. Otherwise, the ongoing write operation willbe suspended and the machine may not start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
If the machine fails to start up, be sure to replace the boot ROM.
18.4.8 Downloading Dcon and Rcon
18.4.8.1 Outline0015-5426
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Dcon/Rcon is downloaded by way of the main controller unit.
Chapter 18
18-25
F-18-45
You will not be able to download Rcon unless the DC controller has started up normally (as, otherwise, the power supply control signal will not be valid and, as aresult, the reader unit remains without power).
18.4.8.2 Downloading Procedure0015-5427
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You can execute a downloading session in either normal or safe mode. In the case of safe mode, however, you will not be able to find out the version of Dcon/Rcon,causing all downloading to occur (overwriting of the same version and downgrading).[Downloading Rcon]1) Select the version of Rcon to download.
F-18-462) Click [Start].
SST
Service PC
Reader unit
iR ----
Dcon
Rcon
Main controller unit
DC controller PCB
Download
Power supply control signal
Power cable
CPU
Reader controller PCB
CPU
Power supply unit
iR ----
Flash ROM
Printer unit
Signal cable
Flash ROM
Chapter 18
18-26
F-18-473) When the downloading session has ended, click [OK].
F-18-484) If you want to execute a different downloading session, see the appropriate instructions.5) When the downloading session has ended, turn off and then on the machine.
6) See the status of upgrading indicated on the control panel of the machine. When a message appears asking you to turn off and then on the machine, turn offand then on the main power.
Be sure never to turn off the machine while it is executing a downloading session or writing downloaded system software. Otherwise, the machine may not be ableto start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
18.4.9 Downloading G3 FAX
18.4.9.1 Outline0015-5428
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The Multi Fax Board-D1 (2-line) comes with a control CPU and its system software, which is downloaded by way of the main controller unit.
Chapter 18
18-27
F-18-49
If a downloading session fails, you will have to replace the flash ROM DIMM.
18.4.9.2 Downloading Procedure0015-5429
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
You will have to use normal mode for downloading.1) Select the version of G3FAX you want to download.
F-18-502) Click [Start].
iR ----
G3Fax
Service PC iR ----
Multi Fax Board (2-line)
Download
Downloading is possible only in normal mode.
G3Fax(Flash ROM DIMM)
G3Fax(Flash ROM DIMM)
Upgrading is also possible by replacing the DIMM.
Main controller unit
CPU
SST
Chapter 18
18-28
F-18-513) When the downloading session has ended, click [OK].
F-18-524) When you are done, turn off and then on the main power of the machine.
5) See the status of upgrading indicated on the control panel of the machine. When a message appears asking you to turn off and then on the machine, turn offand then on the main power.
You will not be able to download G3Fax twice in succession. (Once downloading is executed, the board will be reset, causing download mode to end.)Be sure never to turn off the machine while it is executing a downloading session or writing downloaded system software. Otherwise, the write operation (to theflash ROM DIMM of the G3 fax board) may fail, preventing board functions. In the event the board fails to function, be sure to replace the flash ROM DIMM foundon the G3 fax board.
18.4.10 Uploading and Downloading Backup Data
18.4.10.1 Outline0015-5430
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
SramImg is data that is stored in the SRAM of the main controller PCB, while MeapBack is a MEAP application and its data stored on the HDD.T-18-5
Backup data Files to select for downloading/uploading
Main controller PCB backup RAM SramImg.bin
Chapter 18
18-29
- If you are replacing the main controller PCB, you can transfer such data as parts counter readings by uploading the data before replacement and downloadingit after replacement.- If you are replacing the HDD or executing 'ALL' or 'APL_MEP', you can temporarily set aside MEAP applications by uploading MeapBack before executionand downloading it after execution.- Only the machine uploaded can download SramImg and MeapBack.
F-18-53
18.4.10.2 Uploading Procedure0015-5431
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Use safe mode for uploading.1) Select [Upload Data].
F-18-54
MEAP application MeapBack.bin
for R&D Sublog.txt
Backup data Files to select for downloading/uploading
Service PC
Main controller unit
Main controller PCB
SramImg.bin
iR XXXX
SramImgMeapback
SST
HDD
Meapback.bin
System
Printer unit
SRAM
Uploading/Downloading
Downloading is possible only in safe mode.
Chapter 18
18-30
2) Select the data you want to back up.
F-18-553) Click [Start].
F-18-564) Enter a name of the file to be saved, and fill out a memo as needed. Then, click the save button.
Chapter 18
18-31
F-18-575) Click [OK].
F-18-58
18.4.10.3 Downloading Procedure0015-5432
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Use safe mode for downloading.1) Select [Download Data].
Chapter 18
18-32
F-18-592) Select the data to download.
F-18-603) Click [Start].
Chapter 18
18-33
F-18-614) Click [OK].
F-18-625) When you are done with downloading, turn off and then on the main power.
6) See the status of upgrading indicated on the control panel of the machine. When a message appears asking you to turn off and then on the switch, turn off andthen on the main power.
Be sure not to turn off the machine while it is executing a downloading session or writing downloaded system software. The write operation will be suspended, andthe machine may fail to start up.If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, andRUI.
Chapter 19 Service Tools
Contents
Contents
19.1 Service Tools..............................................................................................................................................................19-119.1.1 List of Special Tools ................................................................................................................................................................ 19-119.1.2 List of Solvents/Oils ................................................................................................................................................................ 19-2
Chapter 19
19-1
19.1 Service Tools
19.1.1 List of Special Tools0015-5434
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The following special tools will be needed in addition to the standard tools set:T-19-1
No. Name Toll No. Shape Rank Remarks
1 Digitalmultimeter
FY9-2002 A Used when making electrical checks.
2 Door switch TKN-0093 A
3 Mirrorpositioning tool(front, rear)
FY9-3009 B Used when positioningthe No. 1/No. 2 mirror.
4 NA-3 Test Sheet FY9-9196 A Used when adjusting/checking images.
5 Potential sensorelectrode
FY9-3012 B Used to make zero-levelchecks on potentialsensors.
6 Environmentsensor checkingsensor
FY9-3014 B Used to check theenvironment sensor.
7 Tester extensionpin
FY9-3038 A Used when makingelectrical checks.
Chapter 19
19-2
T-19-2
19.1.2 List of Solvents/Oils0015-5435
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
T-19-3
8 Tester extensionpin (L-shaped)
FY9-3039 A Used when makingelectrical checks.
Rank:
A: each service person is expected to carry one.
B: each group of five persons is expected to carry one.
C: each workshop is expected to carry one.
No. Name Uses Composition Remarks
1 Alcohol Cleaning:e.g., glass, plastic, rubber parts;external covers.
Fluoride familyhydrocarbon,alcohol, surfaceactivating agent, water
- Do not bring near fire.- Procure locally.- Substitute: IPA (isopropyl alcohol)
2 Solvent Cleaning:metal part; oil, toner.
fluoride familyhydrocarbon, chlorine familyhydrocarbon, alcohol.
- Do not bring near fire.- Procure locally.
3 Heat resistinggrease
Lubrication: fixing drive parts Mineral familylithium soap,molybdenumdisulfide,
Tool No.: CK-0427 (500 g/can)
4 Lubricant Mineral oil(paraffin family)
Tool No.: CK-0524 (100 cc)
5 Lubricant Lubrication: drive parts, friction parts Silicone oil Tool No.: CK-0551 (20 g)
6 Drum cleaning powder Cleaning:photosensitive drum
Cerium oxide Tool No.: CK-0429
7 Lubricant Lubrication: scanner rail Silicone oil Tool No.: FY9-6011 (50 cc)
8 Conductinggrease
Lubrication: drum heater contact Ether, polytetrafluoethylene
Tool No.: FY9-6008 (10 g)
No. Name Toll No. Shape Rank Remarks
Mar 28 2007