Post on 10-Jan-2016
description
1 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
How to configure DCNNG PC Controlled & Camera Control
This presentation is intended to guide the installer step by step through the camera control installation.
Mr. PeetroonsBelgium
DCNNG CC
2 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
How to configure PC controlled DCNNG system with Camera Control
DCN-CCU with direct Camera Control & Virtual Keyboard
DCN-CCU with direct Camera Control & Autodome Controller
DCN-CCU with Allegiant Video Switcher
3 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
DCN-CCUB with direct Camera Control & Virtual Keyboard
Requirements:
One AutoDome Camera One monitor Virtual keyboard software LTC 5138/00
DCN-CCU
DCNNG Control PC DCNNG software LBB 4190/xx
Camera Control Software LBB 4188/xx
4 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Make sure that the Dome camera has an address.
Step 1
Connecting PC and Monitor to AutoDome Camera
RS232
I&U Instructions
Temporary Installation PC
Temporary Installation PC
5 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
AutoDomeCamera
Step 2
Install virtual keyboard software LTC 5138/00
I&U Instructions
Temporary Installation PC
Temporary Installation PC
6 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 3
Configure Virtual Keyboard
7 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 4
Communication Setup
8 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 5
Make sure you choose the right camera!
9 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 6
10 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 7
Quick Commands settings
11 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 8
Pre-Position Title Set
12 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 9
Set Pre-Positions
13 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 10
Pre-Position Shot Name
14 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Repeat
Repeat Steps 9 &10 to set all Pre-Positions
Set the highest Pre-Position as overview
15 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 11
Check the Pre-Positions
To NEXT >>>>>>
16 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
End of how to configure PC controlled:
DCN-CCU with direct Camera Control & Virtual Keyboard
DCN-CCU with direct Camera Control & Autodome Controller
DCN-CCU with Allegiant Video Switcher
17 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
DCN-CCU with direct Camera Control & Autodome Controller
Requirements:
One AutoDome Camera One monitor Autodome Controller LTC 5136/51
DCN-CCU
DCNNG Control PC DCNNG software LBB 4190/xx
Camera Control Software LBB 4188/xx
18 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
AutoDomeCamera
Step 1
Only for Pre setting the Autodome Camera with the Autodome Controller Connect Autodome Controller to data converter LTC 5136/51 Connect Data converter to Aurodome Camera Connect Autodome Camera to Monitor
IUI Autodome
Temporary Autodome Controller
Temporary Autodome Controller
Data ConverterData Converter
For Installation and User Instructions Autodome ControllerFor Installation and User Instructions Autodome Controller
19 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Remark
If you were not successful setting up the pre-positions please don’t continue with the next steps.
First make sure that the pre-positions are set.
20 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
AutoDomeCamera
Step 2
Connect DCN-CCU to DCNNG Control PC and AutoDome Camera
Port 1RS232 RS232
Port 2
I&U Instructions
DCN-CCU
Baudrate 115.2K Baudrate 9.6K
21 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 3
CCU protocol and Serial Port settings DCN-CCU
Make sure that the ports of the CCU are set correct.
Port 1Protocol = FullBaudrate = 115.2K
Port 2Protocol = Camera ControlBaudrate = 9.6K
Keep in mind !You have to change the
baudrate of Port 2 to 9.6K !
S500 Dip switches
I&U Instructions
22 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 4
An installation file must be open before camera installation is possible!
Start Camera Control Software LBB4188
LBB4188
23 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 5
Combine seat numbers with camera pre positions
LBB4188
24 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 6
Make sure you choose the right camera!!Camera nr = Camera Address
LBB4188
25 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 7
Insert
LBB4188
26 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 8
Stop Camera Installation
5
LBB4188
27 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
End of how to configure PC controlled:
DCN-CCU with direct Camera Control & Autodome Controller
DCN-CCU with Allegiant Video Switcher
28 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
DCN-CCU with Allegiant Video Switcher
Requirements:
Allegiant Video Switcher Video Switcher keyboard Fixed and/or AutoDome cameras Monitor(s)
DCN-CCU
DCNNG Control PC DCNNG software LBB 4190/xx
Camera Software LBB 4188/xx
29 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 1
Connecting hardware
BOSCH
30 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 2
Connect DCNNG Control PC and Allegiant Switcher to DCN-CCU
I&U Instructions
Port 1RS232 RS232
Port 2
DCN-CCU
Allegiant SwitcherAllegiant Switcher
Baudrate 115.2K Baudrate 19.2K
31 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 3
CCU protocol and Serial Port settings DCN-CCU
Make sure that the ports of the CCU are set correct.
Port 1Protocol = FullBaudrate = 115.2K
Port 2Protocol = Camera ControlBaudrate = 19.2K
Keep in mind !
You have to change the baudrate of Port 2 to 19.2K !
S500 Dip switches
I&U Instructions
32 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 4
An installation file must be open before camera installation is possible!
Start Camera Control Software LBB4188/xx
LBB4188
33 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 5
Set Pre-Positions using the Video Switcher Keyboard
34 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 6
Combine seat numbers with camera pre positions
LBB4188
35 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 7
Make sure you choose the right camera!!Camera nr = Camera Address
LBB4188
36 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 8
Insert
LBB4188
37 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 9
Stop Camera Installation
5
LBB4188
38 DCNNG IO PCC & CCST/PRM3-EU | |22.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
End of installing:
DCNNG PC controlled with Camera Control
DCNNG CC