History and Restoration Of sailing vessel „La Belle Epoque“

La Belle Epoque was built 1976 – 78 by a german family for intensive travels. She sailed the North and Baltic Seas and even reached the Norwegian coast. But later she was put on land by her second owner, who did not have enough time for maintnance. While waiting on the hard time took its toll...

Summer 2004: we found our dream boat – but she is only a very run down dram boat anymore. We organize the transport to Austria and know that we just bought very much work.

But we are faithful: we do have some practice of restoring boats and working with metall. We know we are facing a complete restoration, but we are convinced that we can handle the work and get a seaworthy and strong boat again. To reach that goal we know we have to bring her home and put her right behind our house in Austria. There we have tools and time, to fix her back up.

All pictures and texts belong to Claudia & Jürgen Kirchbergerand are only for private use und refaring to „www.fortgeblasen.at“

We are happy to hear from our readers: unterwegs@fortgeblasen.at

Transport and restoration site for La Belle Epoque

First of all we have to get right of old paint an rust and of course

close the whole in front of La Belle Epoques rudder.

Jürgen uses a plasma cutter to get the old and thin metal off. We are happy that this is the only critical area of our boat. Where ever we did believe the hull would be thin, we did drill a

whole into the metal and measure its thickness. Just to make sure...

Off course we did weld the wholes tide again!

Getting ready for new and strong metal

At all other areas the hull is rusty, but still strong. We will

sandblast her and give her a new paint job.

We do not like wholes in the hull – not even wholes to fasten gear on deck! All wholes will become leaks one day... So we decide to weld every whole tide and use welded on bolts to

fasten deck gear.

Off course we also close the old dorade ventilation. We will use our hatches to get fresh

air in!

There is more work to do:

cut away the swimming platformfasten extra cleats

and cutting out extra hatchesmounting a new rail

and weld a pilot house

After years of bluewater sailing on board La Belle Epoque we

know now that most of our changes on deck does perfectly fit our needs. But we also think that we could have done some more...

new storage area in the cockpit

new hatches

Welding a pilot house to close the middle cockpit

The boat does have an open aft cockpit with separated steering. But we are hoping to get a boat

that can coop with all sea areas – and give us some comfort in the cold areas. We design our pilot house only for navigation: with second steering station, motor

panel, navigation instruments, big chart table and comfortable

steering seat

In the meanwhile we rip out all old inventory and the old

insulation

Taking out the engine for rebuilt.

More rust inside

We are planing to sand plast the boat inside and outside. Therefor we are preparing the whole

boat and try to get all changes to the boat done before plasting.

Producing everything ourself keeps

the costs down and does realize our ideas.

Pulling out the weight of the keel does give us a bad surprise: the keel is filled with water and oil. We have to get everything out for restoration.

The weight is made out of steel bars

We take the bars out of the boat for cleaning

Luckily there is no rust under the iron bars. We only have to clean the whole area out and give it some new paint.

Reduing the weight with lead

After a year of work: La Belle Epoque is ready for sand plasting:

fixing on 9 layers of paint: epoxyd and polyurethan

Sand helps us to create a anti slip finish

Time to work inside

Finally the engine room is ready for the rebuilt technic

Painting the inside

Meanwile Jürgen starts working on the outside: constructing the

hatches, fixing deck gear

...getting the rudder back in place

...and preparing the cockpit steering unit.

We use Polycarbonat (Lexan and Macrolon) instead of glass: the

material should be able to withstand even the power of

braking waves.

Fun work: painting the boats old name back on her stern!

We learn to know the builder of our boat. He told us, that he

always did have troubles with dirty Diesel: we decide to cut the

tank open for cleaning.

Ready for insulation!

We use Styrodur and foam to insulate the whole boat down to

its waterline with 6 to 8cm insulation.

Starting to do the interior. We want to have a light and friendly finish and decide to use birch plywood

and oak hardwood.

We have old tried oak planks from our own forest, therefor we have to

cut everything ourselves.

Soon we can put in the portholes – and are happy to have a try

vessel from now on!

Time to work on the technic: putting back the drive shaft.

Second steering station inside the pilot house

construction for the Dickinson Diesel stove

Ready to use!

More wood work...

instead of a second head we design a workshop in the boat

owner cabin

Gally and Salon

owner cabin – head – pilot house

Installation and technic

Electric: 12 and 24V

We do have water tide chambers on our boat: thats why we need tide through holes for wires and

not all the work is easy to do...

… but we are getting there!

Outside work:

La Belle Epoque will soon be splashed: time for anti fouling.

Ready to take the roof away...

..and making everything ready for the truck!

It fits!

..and we are on our way! Yupie!!

But we are not doen jet: there is still some work to do on the Danube: Rigg and outside

steering.

We do need a non magnetic steering unit to fit our magnetic compass on top.

Fixing Covers and Bimini, some pillows and small fabric work.

And finally we are putting the masts back on deck. What a excitement: La Belle Epoque is

2009 we are happy to finish our work. We did all of the restoration work ourselves, beside working in regular jobs. We did not work all winters through, since it was way to cold to get paint jobs and

metal work done during Austrian winters.

Looking backwards we are glad we did make the decision to restore La Belle Epoque, even we never sailed the boat before. But after years of bluewater sailing we can still say we made the right

choice for us: La Belle Epoque is still our dream boat!

Learn more about us and our travels: www.fortgeblasen.at

History and Restoration Of sailing vessel „La Belle Epoque“ · History and Restoration Of...

Transcript of History and Restoration Of sailing vessel „La Belle Epoque“ · History and Restoration Of...

History and Restoration Of sailing vessel „La Belle Epoque“ · History and Restoration Of...

Documents

Transcript of History and Restoration Of sailing vessel „La Belle Epoque“ · History and Restoration Of...

England & France During La Belle Epoque

SIA 16 - Le Belle Epoque

Bulgarische Riviera!!Belle Époque Ambelits Beach in erster ...€¦ · 321740741e2914cd2b328e5e5ee357 belle-epoque-2 belle-epoque-3 c1_vynshna_2-2CC Powered by ImmobilienScout24.

Belle Epoque Resumen

PERRIER-JOUËT “Perrier-Jouët Belle Epoque BELLE EPOQUE is ... · Perrier-Jouët Belle Epoque is an icon of the House, the original Belle Epoque cuvée to appear adorned with the

Atas Belle Epoque

Belle epoque noviembre diciembre

La Belle Epoque Group Exhibition

La Belle Epoque (Philippe Julian)

Gran circo belle epoque

Luciana Gennari - Construtores Da Belle Epoque

BELLE EPOQUE - decorunion.itdecorunion.it/wp-content/uploads/2018/03/Catalogo-Belle-Epoque... · belle i fondi epoque 3 bianco ice grigio antracite baroque optical geometry

Cronache e Profili Della Belle Epoque

Speisekarte Belle Epoque€¦ · Salat „Belle Epoque“ (Salatmix, Früchte der Saison) 19,50 „Belle Epoque“ salad (mixed salad, seasonal fruit) Griechischer Salat - Greek salad

Belle epoque jp

I-La Belle Epoque

Belle Epoque Loucos Anos 20

La Belle Epoque Solutions Group

ART - Belle Epoque

Belle Epoque