Post on 31-Aug-2018
2
FEATURES AND BENEFITSQuick Connect:No tools, soldering, clamps, unions or glue required. Cut pipe square, de-burr to remove rough edges/debris, mark the pipe for correct depth and push to get a pressure ready connection every time.
Quick Disconnect:Disconnect in seconds by sliding the Shark Shifter De-Mount Tool down the pipe to engage the demount lugs and rotate clockwise to lock in the open position leaving both hands free, you can now remove the pipe.
SAFE-Recessed Release Collar:SharkBite 2XL requires a special Demount Tool and cannot be accidentally disconnected/released.
Extensive Range Including Slip Feature on Couplings and Tee’s:When repairing or tapping into existing pipe with “Push-Fittings” you must be able to either move the fitting or the pipe to ensure the pipe is engaged fully into the fitting. With rigid pipe like copper the only way with “Push-Fittings” is to have a SLIP feature to allow easy installation when tapping into existing pipe.
Easy Installation:Unlike other tool intensive connection methods there is NO need to send multiple fitters to a job, SharkBite 2XL has been designed to be installed or removed by one person. All fittings are lubricated for easy connection and by fitting the Shark Shifter De-Mount Tool before engaging the pipe the force required can be reduced further. With the De-Mount Tool locked on you also have hands free disconnection.WET OR DRY: No waiting for copper tube to dry before soldering or glue to cure, SharkBite makes an instant connection.
No Tools:Unlike alternative tool intensive connection systems, SharkBite has no special tooling required for installation.
No Time:Fastest connection - CUT-PUSH-DONE.Easy access to small or tight spaces.No Flame - Does not require fire permit or fire marshal.
No Waste:Should you make an error or simply want to change your installation, no problem for SharkBite. Simply remove and re-use. (Fittings used for repeated testing must not be used in any permanent application).
Fittings Cannot be Disassembled:SharkBite 2XL Fittings are factory assembled and components cannot be removed.
Long Pipe Engagement:Provides pipe support against lateral pipe forces.
Lead Free (LF) Dezincication Resistance (DZR) Brass:Exceeds current no lead legislation - AB1953 or NSF372. Suitable for underground installation subject to local code authorites/inspectors. Dezincication properties (DZR) exceed ISO6509 and NSF-14.
Environmentally Friendly:Remove and re-use fittings, no need to be scrapped.No heat is required for installation.
Scan with your mobile device
3
Coupling
1-1/4" SB0135 1-1/2" SB01412" SB0154
SIZE P/N
Slip CouplingSIZE P/N 1-1/4" SB06351-1/2" SB06412" SB0654
Reducing CouplingSIZE P/N 1-1/4" X 1" SB0135281-1/2" X 1-1/4" SB0141352" X 1-1/2" SB015441
Connector FemaleSIZE P/N 1-1/4" X 1-1/4" FNPT SB113532F1-1/2" X 1-1/2" FNPT SB114140F2" X 2" FNPT SB115450F
Connector MaleSIZE P/N 1-1/4" X 1-1/4" MNPT SB113532M1-1/2" X 1-1/2" MNPT SB114140M2" X 2" MNPT SB115450M
90° ElbowSIZE P/N 1-1/4" SB0235 1-1/2" SB02412" SB0254
A B
C
2XL PRODUCT RANGE
Reducing
90º
4
45° Elbow
1-1/4" SB0535 1-1/2" SB05412" SB0554
SIZE P/N
Tee Slip Feature
1-1/4" SB0335 1-1/2" SB03412" SB0354
SIZE P/N
End Cap
1-1/4" SB0435 1-1/2" SB04412" SB0454
SIZE P/N
45° Street Elbow
1-1/4" X FTG SB07351-1/2" X FTG SB07412" X FTG SB0754
SIZE P/N
A
B
^^ Available September 2012
Reducing Tee
1-1/4" X 1-1/4" X 1/2" SB033535161-1/4" X 1-1/4" X 3/4" SB033535221-1/4" X 1-1/4" X 1" SB033535281-1/2" X 1-1/2" X 3/4" SB034141221-1/2" X 1-1/2" X 1" SB034141281-1/2" X 1-1/2" X 1-1/4" SB034141352" X 2" X 1" SB03545428^^
2" X 2" X 1-1/4" SB035454352" X 2" X 1-1/2" SB03545441
SIZE P/N
Slip Feature
2XL PRODUCT RANGE
Slip Feature
Slip Feature
End Cap
5
Ball ValveSIZE P/N 1-1/4" SBBV35 1-1/2" SBBV412" SBBV54
Shark Shifter De-Mount Tools
SIZE P/N 1-1/4" DE-Mount Clip SBDC351-1/2" DE-Mount Clip SBDC412" DE-Mount Clip SBDC54Shifter Set De-MOUNT Tools SBDC354154
PEX Stiffener
1-1/4" SBTL35 1-1/2" SBTL412" SBTL54
SIZE P/N
SPECIFICATION DATABody. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DZR Brass-Lead Free Alloy.O Ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chloramine resistant EPDM.Tube Liner. . . . . . . . . . . . . . . . . . . . . . . . . . . . Copper.Grab Ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Stainless Steel.Locking Ring. . . . . . . . . . . . . . . . . . . . . . . . . . .PSU/PPSU Blend.BV Cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DZR Brass-Lead Free Alloy.BV Ball. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Stainless Steel.BV Spindle. . . . . . . . . . . . . . . . . . . . . . . . . . . . DZR Brass-Lead Free.BV Seat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PTFE.BV Handle. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mild Steel.
CONNECTIONSTube Connections. . . . . . . . . . . . . . . . . . . . . . .CTS.Threaded Connections . . . . . . . . . . . . . . . . . . .Male or Female NPT.Street Connections. . . . . . . . . . . . . . . . . . . . . . CTS.
CERTIFICATIONSIAPMO IGC 157: Ball Valves - This standard covers material, testing, dimensional and performance requirements. ASSE1061: Fittings-Performance requirements for removable & non-removable push-fit fittings.
2XL PRODUCT RANGE
Shark Shifter De-Mount Tools
2.70”
2.94”
2.45”
All SharkBite 2XL Fittings are supplied in individual sealed bags for protection and ensure the fittings remain clean and free of dirt or debris only remove from the bag just prior to installation.
6
Align pipe with the fitting, insert pipe while rotating either pipe or fitting.
SharkBite 2XL PEX Stiffener must be inserted into PEX pipe prior to fitting.
Connection is complete when pipe is fully inserted with depth insertion marked on pipe is still visible at the head of the fitting.
4
Rotate Shark Shifter De-Mount Tool clockwise to locate on lugs, rotate a further 1/2" to disconnect.
Withdraw pipe from fitting then rotate Shark Shifter De-Mount Tool anti-clockwise to remove from fitting.
Shark Shifter De-Mount Tool to pipe just above the connection then slide down to engage lugs on the head of the fitting.
1
2Cut COPPER, CPVC or PEX using a quality Tuber or Pipe Cutter with a sharp blade.
Make sure you have all tools required.
Remove BURRS and ensure pipe surface is free of scratches and any debris. It is CRITICAL that pipe be marked with the correct insertion depth as listed below;
2
Quality engineering. Recessed release collar guarantees NO accidental disconnection; connection can only be released with Shark Shifter Tool.
CONNECTION DISCONNECTION
CONNECTION AND DISCONNECTION
3 3
5
Shark Shifter De-Mount Tool
1
1-1/4" Pipe Insertion Depth = 2" 1-1/2" Pipe Insertion Depth = 2-1/4"
2" Pipe Insertion Depth = 2-1/2"
7
De-Burr
Pipe 1. clearof branch
Insertiondepth mark
Insertiondepth mark
Slip End Stop End
Pipe 1
Pipe 1
Pipe 1
Pipe 1
Pipe 2
Pipe 2
Pipe 2
Pipe 2
SLIP FEATURE
PROBLEM.Identify the section to be removed for repair using a SLIP Coupling and if you are tapping into an existing pipe line using a SLIP Tee.Mark section to be removed depending on the pipe size as per following; 1-1/4" Pipe repairable section 2-1/2". 1-1/2" Pipe repairable section 2-3/4".
2" Pipe repairable section 3" (Demonstratedhere)Nominated repairable section must be removed any smaller section will not provide room to engage the second pipe and would partially block flow of the branch on a Tee. Larger sections would create short engagement and installation failure.
1
CUT.Cut out section using a quality Tuber or Pipe Cutter with a sharp blade. Remove BURRS and ensure pipe surface is free of scratches and any debris. It is CRITICAL that BOTH pipes be marked with the correct insertion depth as listed below; 1-1/4" Pipe Insertion Depth = 2". 1-1/2" Pipe Insertion Depth = 2-1/4". 2" Pipe Insertion Depth = 2-1/2". (Demonstratedhere)
2
PUSH.All SLIP Couplings and Tee’s come fitted with an instruction band at the SLIP END of the fitting stating;
Align pipe 1 with the bore of the SLIP END of the fitting. Insert pipe 1 while rotating either pipe or fitting until the stop end of the fitting is clear of pipe 2.**NOTE-AtthispointtheboreofthebranchoftheTeeiscompletelyblocked.
Engage Shark Shifter De-Mount Tool to the SLIP END of the fitting the grab ring teeth and now disengaged allowing pipe 1 to be withdrawn. Shark Shifter can be fitted prior to or after SLIP end if engaged.
SIZE OF PIPE for installation. Size of section that can be removed. Insertion mark depth on both pipes. Direction fitting is to move.
3
DONE.With the Shark Shifter fitted to the SLIP END withdraw pipe 1 allowing pipe 2 to engage up to the INSERTION DEPTH MARK and NOT withdrawing pipe 1 any further than the INSERTION DEPTH MARK, marked on pipe 1.**NOTE-Pipeisnowclearofthebranchallowingfullflow.
YoucannowremoveSharkShifterDe-MountToolfromtheSLIPEndofthefitting.
You have now completed a repair or added a new line into an existing system in minutes. Remember all SharkBite® Fittings can be installed WET or DRY, and suitable for use on COPPER, CPVC and PEX.**NOTE-PEXPipecanbeused(requiresaSharkBite®PEXStiffenerpushedfirmlyintopipe)providedSharkShifterToolisfittedtotheSLIPEndofthefittingpriortopipeinsertionintofitting.
4
SLIP FEATURE FUNCTIONThe SLIP Feature Function is unique to the SharkBite® 2XL range apart from the largest range of large bore Push-to-Connect Fittings in the Nth American market, SharkBite® 2XL SLIP Couplings and ALL Tee’s come with the SLIP Feature Function as standard. Demonstrated below is the correct procedure for installing SharkBite® SLIP Couplings and Tee’s with the Slip Feature Function into a 2" COPPER Pipe.NOTE - PEX PIPE can be used (requires a SharkBite® PEX Stiffener pre-fitted to pipe) provided the Shark Shifter Tool is fitted to the SLIP End of the fitting prior to pipe insertion into fitting.
Reliance Worldwide USA2727 Paces Ferry Road SEBuilding Two, Suite 1800Atlanta, GA 303391-877-700-4242 Fax: 1-877-700-4280www.sharkbite.com
Reliance Worldwide Canada74 Alex AvenueVaughan, Ontario, L4L 5X11-888-820-0120Fax: 1-905-265-2775www.sharkbite.com
Manufactured and Distributed by Reliance Worldwide Corporation
FITTINGS
GAUGESSTOPS & FIXTURE SUPPLY FITTINGS
FLEXIBLE CONNECTORS VALVES TOOLS
KITS
PEX
SLIP FITTINGS
REGULATORS & THERMOSTATIC VALVES
2XL - 1 1/4", 1 1/2” & 2"
* Gray water, rainwater harvesting and reclaimed water systems only. Not potable water.
SIZE P/N
Dual Tee Stop Valve Adaptor1/2" CTS X 1/2" CTS X 1/2" U782*
SIZE P/N 1/2" X 1/4" (3/8" OD) 23048-0000*1/2" X 3/8" comp 23036-0000* 1/2" X 1/4" comp 23336-0000*1/2" X 1/2" comp 23489-0000*
Angle Stops1/4" (3/8" OD) X Toilet Valve, Straight U3531*1/4" (3/8" OD) X Toilet Valve, Elbow U3537*
Toilet ConnectorsSIZE P/N
SIZE P/N – U702*
Safe Seal Tools
Reliance Worldwide USAPhone: 1-877-700-4242 Fax: 1-877-700-4280
Reliance Worldwide CanadaPhone:1-888-820-0120 Fax: 1-905-265-2775
Easy InstallatIonEnsure the pipe is cut square, using the deburr tool (U702) – remove rough edges/debris and mark the pipe for correct depth. Push pipe and fitting together up to the depth mark.
INSTALLATION AND DISCONNECTIONFast DIsassEmblyUsing the simple disconnect clip or tongs, fittings can be easily changed and reused.
• Connects copper, CPVC and PEX pipe in any combination.• No soldering, clamps, unions or glue.• Certified to 200 psi and 200ºF.• Certified for underground and behind the wall applications and as a manufactured joint without access panels.• All SharkBite® Brass Products including LEAD FREE are DZR Brass.• Certified for potable water and hydronics.• Integral tube liner for PEX installations.• Fittings can even be rotated after assembly for easier installation in tight spaces.• Easy to disconnect if needed.
* Available in Lead Free
www.sharkbite.comwww.sharkbite.com
SIZE P/N
Water Hammer Arrestors1/2" Residential 22630*1/2" Commercial 22631*3/4" Residential 22632*1" Commercial 22633*
1/4" X 3/8" MNPT U276*1/4" (3/8" OD) X 3/4" GH U2276*1/2" X 3/8" MNPT U281*
SIZE P/N Dishwasher Elbows
SIZE P/N 1/4" (3/8" OD) U004* 3/8" (1/2" OD) U006* 1/2" U008* 5/8" U012 3/4" U016* 1" U020*
CouplingsSIZE P/N
SIZE P/N
Reducing Couplings
SIZE P/N 1/2" X 1/2" FNPT U072*3/4" X 3/4" FNPT U088*3/4" X 1/2" FNPT U092* 1"X 1" FNPT U094*
Connectors FemaleSIZE P/N 1/4" (3/8" OD) X 1/2" FNPT U066* 3/8" (1/2" OD) X 1/2" FNPT U070*1/2" X 3/4" FNPT U068*
1/2" X 1/2" MNPT U120*3/4" X 3/4" MNPT U134*1"X 1" MNPT U140*1" X 3/4" MNPT U142
SIZE P/N
Connectors Male1/4" X 1/2" MNPT U110* 3/8" (1/2" OD) X 1/2" MNPT U118* 1/2" X 3/4" MNPT U116*5/8" X 3/4" MNPT U1263/4" X 1/2" MNPT U138*3/4" X 1" MNPT U139*
SIZE P/N
Polybutylene Conversion Couplings1/2" PB U4008* 3/4" PB U4016*
1/4" (3/8"OD) X 1/2" U050*3/8" (1/2" OD) X 1/2" U009*3/4" X 5/8" U057 3/4" X 1/2" U058*1" X 3/4" U060*
SIZE P/N
Reducing Elbows1/2" X 3/8" (1/2" OD) U272*3/4" X 5/8" U2733/4" X 1/2" U274*1" X 3/4" U278*
SIZE P/N 3/8" (1/2" OD) X 1/2" FNPT U332*1/2" U249*1/2" X 1/2" FNPT U334*3/4" X 1/2" FNPT U340*
Drop Ear Elbows
1/2" X 1/2" FNPT U335*SIZE P/N Hy-Ear Elbows
SIZE P/N
Manifolds with SharkBite® Push-fit Branches3 port open 22995*3 port closed 22996*4 port open 22997*4 port closed 22998*
SIZE P/N Stub-out Elbows1/2" Copper Tube 8" LG U351A*
SIZE P/N EB-25 3/4" 22857-0045EB-25 1" 22927-0045EB-35 1/2" 22858-0045EB-35 3/4" 22859-0045EB-35 1" 22928-0045EB-45 1/2" 22860-0045EB-45 3/4" 22861-0045* EB-45 1" 22929-0045*
With SharkBite® Double Unions & 45 psi Set Pressure
SIZE P/N
EB-45 Temporary Bypass Kits
EB-45 3/4" 22934SIZE P/N EB-45 3/4" 22950-0060*EB-45 1" 22951-0060*
With SharkBite® Double Unions & 60 psi Set Pressure
SIZE P/N
Elbows1/4" (3/8" OD) U244*3/8"(1/2" OD) U246*1/2" U248*5/8" U2523/4" U256*1" U260*
Threaded Adapters
3/4"CTS X 3/4" FNPT U766*1"CTS X 1" FNPT U772*
SIZE P/N 3/8" (1/2" OD) X 1/2" CTS U719*
3/8" (1/2" OD) X 3/4" CTS U721*1/2" X 1" CTS U722*3/4" X 1" CTS U724*
Fitting Reducers
(Use to connect to smaller pipe sizes)
SIZE P/N
SIZE P/N 3/8"(1/2" OD) U512*1/2" U514*5/8" U5163/4" U518*1" U520*
End StopsSIZE P/N
Slip Couplings**
1/2" U3008*3/4" U3016*1" U3020*
Only suitable for Copper and CPVC
SIZE P/N 1/2" U3362*3/4" U3370*
Slip Tees**Slip Run is only suitable for Copper or CPVC
SIZE P/N 1/2" FNPT (SLIP) U3482*3/4" FNPT U462*3/4" FNPT (SLIP) U3486*1" FNPT U464*
Female Centre Slip Tees**
Slip Run is only suitable for Copper and CPVC
1/4" (3/8" OD) U358*3/8" (1/2" OD) U360*1/2" U362*5/8" U3663/4" U370*1" U374*
TeesSIZE P/N
Reducing Tees1/2" X 1/2" X 1/4" (3/8" OD) U359*1/2" X 1/2" X 3/8" (1/2" OD) U363*3/8" (1/2" OD) X 3/8" (1/2" OD) X 1/2" U364*3/4" X 3/4" X 1/2" U412*3/4" X 1/2" X 3/4" U444*3/4" X 1/2" X 1/2" U454* 1" X 1" X 3/4" U416*
SIZE P/N
SIZE P/N 1/2" X 1/4" (3/8" OD) 23049-0000*1/2" X 3/8" comp 23037-0000*1/2" X 1/4" comp 23337-0000*1/2" X 1/2" comp 23490-0000*
Straight StopsSIZE P/N 1/4" (3/8" OD) X 3/8"compression nut U3523*Converts 3/8" compression stop to SharkBite®
Stop Valve Connectors
SIZE P/N
Stop Valve Tee Adapters1/4" (3/8"OD) X 1 /4" (3/8"OD) X 3/8" compression nut U3358*1/4" (3/8"OD) X 1/4" (3/8" OD) X 1/4" (3/8"OD) tube U4358*
1/4" (3/8" OD) X 1/2" Faucet Valve U3525*
Faucet ConnectorsSIZE P/N
SIZE P/N Contractor Kits – 22486*Contractor Kit Case Only U3001*
SIZE P/N – 22795*
Irrigation KitsSIZE P/N
Water Heater Installation Kits1/2" X 3/4" FNPT 22604*3/4" X 3/4" FNPT 22441*
SIZE P/N Faucet w/ Angle Stop 23387*Faucet w/ Straight Stop 23388*Toilet w/ Angle Stop 23389*Toilet w/ Straight Stop 23390*
Faucet & Toilet Kits
LENGTH BLACK TEXT
1" PEX Oxygen Barrier20' straight U880O20100' coil U880O100300' coil U880O300500' coil U880O500
LENGTH BLACK TEXT
1/2" PEX Oxygen Barrier20' straight U860O20100' coil U860O100300' coil U860O300500' coil U860O5001000' coil U860O1000
LENGTH BLACK TEXT
5/8" PEX Oxygen Barrier300' coil U865O300
LENGTH BLACK TEXT
3/4" PEX Oxygen Barrier20' straight U870O20100' coil U870O100300' coil U870O300500' coil U870O5001000' coil U870O1000
LENGTH BLACK TEXT
3/8" (1/2" OD) PEX Oxygen Barrier100' coil U855O100300' coil U855O300500' coil U855O500
SIZE P/N 1-1/4" SB0135 1-1/2" SB01412" SB0154
CouplingSIZE P/N 1-1/4" X 1" SB0135281-1/2" X 1-1/4" SB0141352" X 1-1/2" SB015441
Reducing Coupling
SIZE P/N 1-1/4" X 1-1/4" FNPT SB113532F1-1/2" X 1-1/2" FNPT SB114140F2" X 2" FNPT SB115450F
Connector FemaleSIZE P/N 1-1/4" x 1-1/4" MNPT SB113532M1-1/2" x 1-1/2" MNPT SB114140M2" x 2" MNPT SB115450M
Connector MaleSIZE P/N 1-1/4" SB0535 1-1/2" SB05412" SB0554
45º ElbowSIZE P/N 1-1/4" SB0435 1-1/2" SB04412" SB0454
End Cap
SIZE P/N 1-1/4" SBBV35 1-1/2" SBBV412" SBBV54
Ball Valve
SIZE P/N 1-1/4" SBDC351 1/2" SBDC412" SBDC54Shifter Disconnect Tool Kit SBDC354154
2XL Shifter Disconnect Clips
SIZE P/N 1-1/4" SBTL35 1-1/2" SBTL412" SBTL54
PEX Stiffener
3/4" PEX Blue, Red or White5' straight U870B5 U870R5 U870W510' straight U870B10 U870R10 U870W1020' straight U870B20 U870R20 U870W2025' coil U870B25 U870R25 U870W2550' coil U870B50 U870R50 U870W50100' coil U870B100 U870R100 U870W100300' coil U870B300 U870R300 U870W300500' coil U870B500 U870R500 U870W500
LENGTH BLUE RED WHITE 5' straight U880B5 U880R5 U880W510' straight U880B10 U880R10 U880W1020' straight U880B20 U880R20 U880W20100' coil U880B100 U880R100 U880W100300' coil U880B300 U880R300 U880W300500' coil U880B500 U880R500 U880W500
LENGTH BLUE RED WHITE 1" PEX Blue, Red or White
1/2" PEX Blue, Red or White5' straight U860B5 U860R5 U860W510' straight U860B10 U860R10 U860W1020' straight U860B20 U860R20 U860W2025' coil U860B25 U860R25 U860W2550' coil U860B50 U860R50 U860W50100' coil U860B100 U860R100 U860W100300' coil U860B300 U860R300 U860W300500' coil U860B500 U860R500 U860W500
LENGTH BLUE RED WHITE 3/8" (1/2" OD) PEX Blue, Red or White5' straight – – U855W510' straight – – U855W10 50' coil – – U855W50100' coil U855B100 U855R100 U855W100
LENGTH BLUE RED WHITE LENGTH BLACK TEXT
1/4" (3/8" OD) PEX Gray Color5' straight U850G550' coil U850G50
SIZE P/N Coupling Hoses1/2" x 1/2",18" LG U3008FLEX18*3/4" x 3/4",18" LG U3016FLEX18*
1/2" X 3/4" FIP, 12" U3068FLEX12*1/2" X 3/4" FIP, 15" U3068FLEX15*1/2" X 3/4" FIP, 18" U3068FLEX18*1/2" X 3/4" FIP, 24" U3068FLEX24*3/4" X 3/4" FIP, 12" U3088FLEX12*3/4" X 3/4" FIP, 15" U3088FLEX15*3/4" X 3/4" FIP, 18" U3088FLEX18*3/4" X 3/4" FIP, 24" U3088FLEX24*
Water Heater ConnectorsSIZE P/N SIZE P/N
1/2" BV X 3/4" FIP, 18" U3068FLEX18BV*3/4" BV X 3/4" FIP, 18" U3088FLEX18BV*
Water Heater Connectors with Ball Valve
SIZE P/N 1/2" X 1/2" FNPT 22182-0000*3/4" X 3/4" FNPT 22186-0000*1" X 1" FNPT 22187-0000*
SharkBite® x FNPT
1/2" with drain 22304-00003/4" with drain 22305-00001" with drain 22306-0000
SIZE P/N
SharkBite® x SharkBite® with Drain/Vent
SIZE P/N
Thermostatic Valves with SharkBite® UnionsHG-110D 1/2" 24104-0000*HG-110D 3/4" 24105-0000*HG-115H 3/4" 24326-0000HG-115D 3/4" 24328-0000HG-160 1/2" 24343-0000HG-160 3/4" 24345-0000
SIZE P/N
With SharkBite® Unions and Check ValvesHG-110D 1/2" with checks 24341-0000*HG-110D 3/4" with checks 24342-0000*HG-115H 3/4" with checks 24327-0000HG-115D 3/4" with checks 24329-0000HG-160 1/2" with checks 24344-0000HG-160 3/4" with checks 24346-0000
SIZE P/N
Integral Connectors for Thermostatic Valves1/2" 24311-0000 3/4" 24312-0000
SIZE P/N
Pressure Gaugeswith 1/2" Tee 22770with 3/4" Tee 22772with 1" Tee 227741/2" Tube Size 228833/4" Tube Size 22885
Temperature Gaugeswith 1/2" Tee 22771with 3/4" Tee 22773with 1" Tee 227751/2" Tube Size 228843/4" Tube Size 22886
SIZE P/N
SIZE P/N 1/2" 22222-0000*3/4" 22185-0000*1" 22223-0000*
SharkBite® x SharkBite®
SIZE P/N 1/2" U2008-0000A*3/4" U2016-0000A*1" U2020-0000A*
Check ValvesSIZE P/N 1/4" U706*3/8" U708*1/2" U710*5/8" U3712*3/4" U712*1" U714*
Disconnect Clips
SIZE P/N 1/2" U711*3/4" U713*1" U715*
Disconnect Tongs
1/2" X 1/2" X 1/2" CTS U4482*
Service Slip Tee Adapters**
Slip Run is only suitable for Copper or CPVC
SIZE P/N
SIZE P/N 1-1/4" SB06351-1/2" SB06412" SB0654
Slip Coupling
1-1/4" SB0335 1-1/2" SB03412" SB0354
Slip TeeSIZE P/N SIZE P/N
1-1/4" x 1-1/4" x 1/2" SB033535161-1/4" x 1-1/4" x 3/4" SB033535221-1/4" x 1-1/4" x 1" SB033535281-1/2" x 1-1/2" x 3/4" SB034141221-1/2" x 1-1/2" x 1" SB034141281-1/2" x 1-1/2" x 1-1/4" SB034141352" x 2" x 1-1/4" SB035454352" x 2" x 1-1/2" SB03545441
Reducing Slip TeeSIZE P/N 1-1/4" x FTG SB05351-1/2" x FTG SB05412" x FTG SB0554
45º Street Elbow
SIZE P/N 1-1/4" SB0235 1-1/2" SB02412" SB0254
90º Elbow
Plumbing Solutions
SIZE P/N EB-35 1/2" 22670-0045EB-35 3/4" 22671-0045EB-35 1" 22672-0045EB-45 1/2" 22673-0045EB-45 3/4" 22674-0045*EB-45 1" 22675-0045*
With SharkBite® Direct Connectors
SharkBite® Insulated PEX Tubing100' coil 3/8" U855I100100' coil 1/2" U860I100100' coil 3/4" U870I100100' coil 1" U880I100
LENGTH SIZE BLACK TEXT
LENGTH SIZE PURPLE
SharkBite® Reclaimed Water PEX Tubing*
100' coil 1/2" U860P100300' coil 1/2" U860P300100' coil 3/4" U870P100300' coil 3/4" U870P300100' coil 1" U880P100300' coil 1" U880P300
NEW NEW
NEWSIZE P/N 1/4" (3/8"OD) X 3/8" MNPT U276* 1/2" X 3/8" MNPT U281*1/2" X 1/2"MNPT U280*3/4" X 3/4" MNPT U286*
Male Elbows
NEW
SIZE P/N
Female Elbows1/4" (3/8"OD) X 3/4" GH U2276*1/2" X 1/2" FNPT U308*3/4" X 3/4" FNPT U314* NEW
** Slip Run is only suitable for Copper or CPVC
NEW
SharkBite® PosterAvailable in 3 sizes 24" x 36", 18" x 24" & 11" x 17". Showing all 200 SharkBite® product including 2XL and PEX Pipe.
Plumbing Solutions
Plumbing Solutions
MAKE YOUR OWN
RISERS
Use SharkBite® PEX
tubing with SharkBite®
chrome fittings and
stops for all supply-to-
fixture connections.
Make your own risers using SharkBite® PEX tubing. Then finish the supply line to fixture or appliance connections with SharkBite® push-fit fittings and chrome stops.
THE SHARKBITE® CONNECTION SYSTEM Lightning Fast. Won’t Let Go.
EASY INSTALLATIONEnsure the pipe is cut square, using the deburr tool (U702) – remove rough edges/debris and mark the pipe for correct depth. Push pipe and fitting together up to the depth mark.
FAST DISASSEMBLYUsing the simple disconnect clip or tongs, fittings can be easily changed and reused.
INSTALLATION AND DISCONNECTION
The SharkBite® push-fit fittings have been design certified and listed to ASSE 1061/NSF 61. The SharkBite® push-fit fittings are listed by IAPMO and are certified for potable and hydronic heating water distribution (note: Glycol mixture for hydronics can be 100% concentration). The SharkBite® push-fit fittings have been certified for underground applications and as a manufactured joint without access panels and they meet UPC, IPC and cUPC requirements. Please consult with local plumbing codes concerning specific applications.
The SharkBite® tubing without oxygen barrier is approved for all model codes in the US and Canada for use in potable water systems and is certified to the following standards: NSF 14/61, NSF P171, ASTM F 876, ASTM F 877, CSA B137.5 and AWWA C904.
The SharkBite® tubing with oxygen barrier is approved for use in all model codes in the US and Canada for use in hydronic and potable water systems and is certified to the following standards: NSF 14/61, NSF P171, ASTM F 876, ASTM F 877, CSA B137.5 and AWWA C904. SharkBite PB Couplings are designed to work with ASTM D3309 spec polybutylene, do not install onto damaged or decayed PB pipe.
CERTIFICATIONS
Reliance Worldwide USA2727 Paces Ferry Road SEBuilding Two, Suite 1800Atlanta, GA 303391-877-700-4242 Fax: 1-877-700-4280cashacme.com
Reliance Worldwide Canada74 Alex AvenueVaughan, Ontario, L4L 5X11-888-820-0120Fax: 1-905-265-2775cashacme.ca
Manufactured and Distributed by Reliance Worldwide Corporation
Use SharkBite® fittings for fast supply line to fixture connections.
23048-0000
U3525
U850G5
U860W5
U850G5U2276 U3358
23036-0000
U351
U4482
The Chrome Trim Cap can be removed and reversed for use as a handy disconnect tool.
Use like a disconnect clip to press against the fitting collar and release the pipe.
DIAMETER LENGTH P/N1/4" (3/8"OD) 5' straight U850G5Gray Color 50' coil U850G50
SharkBite® PEX Tubing
Nominal Sizeof Fitting
Nominal Sizeof Tubing
TubingOD Size
TubingID Size
1/4" 1/4" CTS 3/8" 0.305"1/2" 1/2" CTS 5/8" 0.475"1/4" compression 1/4" ACR 1/4" 0.190"3/8" compression 3/8" ACR 3/8" 0.311"
SharkBite® Fittings/Tube Size Compatibility
Make Your Own RiserA complete range of SharkBite® fittings, stop valves and PEX Tubing it’s easy to make risers the exact length needed for connecting fixtures and appliances.
SharkBite® Peg Board DisplayHard display of NEW and exciting SharkBite® product.
1
1-877-700-4242
SharkBite® CatalogFull comprehensive listing of all SharkBite® Push-to-Connect from 1/4" through to 1" including PEX Pipe and SharkBite® BARB Fittings.
EB-2
5St
ainl
ess
Stee
l
EB-2
5-40
0
EB-2
5
EB-5
EB-7
5
E-3
E-41
Pressu
reguar
dPS
L
E-56
EB-4
5
EB-3
5
EB-25
Mult
i Ca
rtridg
e
EB-2
5 Lo
w S
et
Res
iden
tial,
Indu
stria
l,C
omm
erci
al
Res
iden
tial
Res
iden
tial
Res
iden
tial
Irrig
atio
n,Ag
ricul
ture
Com
mer
cial
,In
dust
rial
Com
mer
cial
,In
dust
rial
RVs, D
ishwa
shers,
Washi
ng Ma
chines
,Wa
ter Me
ters, S
oftener
sand
Fount
ains
Com
mer
cial
,In
dust
rial
Res
iden
tial
Res
iden
tial
Indu
stria
l,C
omm
erci
al
Light
Indus
trial,
Hydro
nics H
eatin
g
Wat
er,
Dry
Air
Wat
er
Wat
er
Wat
er
Wat
er
Air,
Wat
er
Wat
er
Wat
er
Air, W
ater,
Light
Oils,
Ga
ses (
exce
pt ste
am)
Wat
er
Wat
er
Wat
er
Wat
er
180˚
F
180˚
F
180˚
F
180˚
F
180˚
F
180˚
F
180˚
F
175˚
F
180˚
F
180˚
F
180˚
F
180˚
F
180˚
F
300
psi
400
psi
300
psi
300
psi
300
psi
300
psi
300
psi
300
psi
400
psi (
225
psi f
or fla
nged
ve
rsion
)
400
psi (
1/2”
, 3/
4”, 1
”) 30
0 ps
i (1-
1/4”
, 1-
1/2”
, 2”)
300
psi
250
psi
300
psi
20-9
0 ps
i
20-9
0 ps
i
20-9
0 ps
i
20-7
0 ps
i
10-7
0 ps
i
20-7
0 ps
i
20-7
0 ps
i
N/A
15-5
0 ps
i,40
-60
psi,
50-1
10 p
si,80
-125
psi
10-7
0 ps
i 71-
150
psi (
high
pres
sure
ra
nge)
45 ps
i; 60 p
si 12
psi (3
/4”);
125 p
si (h
igh
pres
sure
ra
nge o
nly)
20-70
psi
(1/2”
and 3
/4”)
20-90
psi (1
”)
20-9
0 ps
i
8-35
psi
45 p
si
45 p
si
45 p
si
45 p
si
45 p
si
45 p
si
45 p
si
50 p
si
N/A
45 o
r 60
psi
55 p
si -
50
psi -
45
psi
25 p
si
Thre
aded
(NPT
) and
Dou
ble
Uni
on 3
/4”,
1” T
hrea
ded
Onl
y
Sing
le Un
ion 1
/2”,
3/4”
and
1”;
Swea
t and
Thr
eade
d Do
uble
Union
3/
4” a
nd 1
”; Sw
eat a
nd T
hrea
ded
Doub
le Un
ion P
EX 3
/4” a
nd 1
”
Sing
le a
nd D
oubl
e U
nion
1/2
”, 3/
4”, 1
”, 1-
1/4”
, 1-1
/2” a
nd 2
”;Sw
eat a
nd T
hrea
ded
Shar
kBite
® D
oubl
e U
nion
3/4
” onl
y;D
oubl
e U
nion
PEX
3/4
” and
1”
Sing
le U
nion
1/2
”, 3/
4”, 1
”, 1-
1/4”
, 1-1
/2”,
2” a
nd 2
-1/2
” Th
read
ed O
nly
Thre
aded
(NPT
) 1/2
” and
3/4
”
Thre
aded
(NPT
) 1/2
”, 3/
4”, 1
”, 1-
1/4”
, 1-1
/2” a
nd 2
”
Thre
aded
(NPT
) 1/2
”, 3/
4”, 1
”, 1-
1/4”
, 1-1
/2” a
nd 2
”
Thre
aded
(NPT
) 3/8
” and
1/2
”; C
ompr
essi
on 3
/8” O
D a
nd 5
/8”
OD
; Hos
e C
onne
ctio
n 3/
4”
Thre
aded
(NPT
) 2”,
2-1/
2” a
nd 3
”; 15
0 lb
MSS
flan
ges
2”,
2-1/
2” a
nd 3
”
Sing
le an
d Do
uble
Union
1/2
”, 3/
4”, 1
”, 1-
1/4”
, 1-1
/2”,
& 2”
; Swe
at
and
Thre
aded
(NPT
) 1/2
”, 3/
4”, 1
”, 1-
1/4”
, 1-1
/2” &
2”;
Doub
le Un
ion P
EX 3
/4” &
1”;
Doub
le Un
ion C
PVC
3/4”
& 1
”; Di
rect
Thre
ad
Shar
kBite
® 1/2
”, 3/
4” &
1”;
Doub
le Un
ion S
hark
Bite
® 3/4
”; Hi
gh
Pres
sure
Ran
ge S
ingle
Union
1/2
”, 3/
4”, 1
”, 1-
1/2”
& 2
”
Sing
le an
d Do
uble
Union
1/2
”, 3/
4” a
nd 1
”; Sw
eat a
nd T
hrea
ded
(NPT
) 1/2
”, 3/
4” a
nd 1
”; Do
uble
Union
PEX
3/4
”,1”;
Dire
ct Th
read
Sh
arkB
ite® 1
/2”,
3/4”
, 1”;
Doub
le Un
ion S
hark
Bite
® 1/2
”, 3/
4”
Thre
aded
(NPT
) or A
SME
B16.
24 C
L150
Fla
nged
2-1
/2” a
nd
3” A
SME
B16.
24 C
L150
Fla
nged
Onl
y 4”
Sing
le Un
ion 1
/2”,
3/4”
, 1”;
Doub
le Un
ion 3
/4”,
1” T
hrea
ded
Only
ASSE
, IAP
MO
(UPC
c) to
ASS
E st
d.10
03
and
CSA
std
. B-3
56
ASSE
, IAP
MO
(UPC
c) to
ASS
E st
d.10
03
and
CSA
std
. B-3
56
ASSE
, IAP
MO
(UPC
c) to
ASS
E st
d.10
03
and
CSA
std
. B-3
56
Unl
iste
d
ASSE
, IAP
MO
(UPC
) to
ASSE
std
.100
3 an
d C
SA s
td. B
-356
ASSE
, IAP
MO
(UPC
) to
ASSE
std
.100
3
ASSE
, ASS
E st
d.10
03
Unl
iste
d
Unl
iste
d
ASSE
, IAP
MO
(UPC
c) to
ASS
E st
d. 1
003
and
CSA
std
. B-3
56 (e
xcep
t hig
h pr
essu
re
rang
e)
ASSE
, IAP
MO
(UPC
c) to
ASS
E st
d. 1
003
and
CSA
std
. B-3
56
Unl
iste
d
Unl
iste
d
Mod
elA
pplic
atio
nSe
rvic
eM
axTe
mp
Max
Pr
essu
reO
utle
t Pr
essu
re
Ran
ge
Stan
dard
Fa
ctor
y Se
tting
List
ings
Con
nect
ions
HO
W T
O O
RD
ER: T
o or
der,
spec
ify C
ash
Acm
e va
lve
type
by
spec
ific
serie
s de
sign
atio
n an
d th
e en
d co
nnec
tion,
if a
pplic
able
. Als
o st
ate
the
follo
win
g: 1
. Val
ve p
ipe
size
. 2. F
luid
to b
e co
ntro
lled.
3. I
nlet
pre
ssur
e. 4
. Out
let
pres
sure
set
ting
and
rang
e. 5
. Max
imum
requ
ired
flow
rate
. 6. S
yste
m o
pera
ting
tem
pera
ture
.
PRV BrochureA guide to the complete Pressure Regulating Valve family, built by Cash Acme.
MultiFLEXThe newest member to the Heatguard® family, the complete water heater temperature control kit. Delivers safe water and increase household hot water demands.
Website Training VideosVisit the How It Works section of sharkbite.com for a complete library of SharkBite® installation videos including SharkBite® 2XL.
TRAINING ACADEMY
SharkTechLearn how to use SharkBite® and other Cash Acme products with the SharkTech Training team. Email info@sharkbite.com for more information about training programs.
Heatguard® TAFRTemperature ActuatedFlow ReducersThermal element senses high temperature water and reduces flow to protect user. Device will only reset when water temperature drops to a safe level. The Heatguard® TAFR is used for shower, tub or faucet spouts to act as a “hot water fuse" to reduce flow of water if it reaches 120°F (49°C).
Reliance Worldwide USA2727 Paces Ferry Road SEBuilding Two, Suite 1800Atlanta, GA 303391-877-700-4242 • Fax: 1-877-700-4280cashacme.com
Reliance Worldwide Canada74 Alex AvenueVaughan, Ontario, L4L 5X11-888-820-0120 • Fax: 1-888-820-0121cashacme.ca
Order Desk1-888-820-0120FAX: 1-888-820-0121www.cashacme.ca
A Division of the Reliance Worldwide Corporation
Getting More Hot WaterThermostatic Mixing valves are the SolutionWhen more hot water is needed, Cash Acme has an easy, cost effective solution. Our Thermostatic Mixing Valves allow the existing heater to store water at a high temperature that might otherwise scald, while delivering it at a safe 120°F or lower to all faucets. This makes the effective heater capacity much greater– typically 50% more gallons with electric heaters. And even more than that with gas. As shown in the chart, when the temperature is increased to 160°F on a 30 gallon water heater, the effective gallons available at 120°F will be 46 to 57 gallons depending on the cold water temperature. That’s as much as an 89% increase in available hot water from the same water heater.
(based on a 30 gallon water heater.)
Thermostatic Retrofit KitRetrofit Tailpiece KitThe Thermostatic Retrofit Kit comes with 3 CTS tailpieces. The kit aids in the quick and easy installation of a thermostatic mixing valve in a domestic application. Use with SharkBite® fittings to easily connect a Heatguard® valve to 1/2" and 3/4" pipe. Heatguard® 110-D purchased separately. For use with Heatguard® thermostatic mixing valves.
Heatguard® 800 SeriesThermostatic Master Controller for Commercial and Industrial ApplicationsTemperature Range: 95-150°F, Max Pressure: 145 psi.Fast acting, high quality thermostatic elements that sense the outlet temperature and react to maintain a stable delivery temperature even under varying and extremely low flows. The adjusting handle can be locked at a desired temperature. Each valve has integral mounting feet to allow it to be securely fixed to a wall or frame. Complete with 4in1 service fittings on each inlet. Every valve is factory tested. The Masterguard® Series features a range of six high flow rate Thermostatic Mixing Valves that mix hot water with cold water to deliver tempered water at a controlled temperature, typically 120°F (49°C). Intended for installation in the plant room of commercial and industrial facilities to distribute controlled temperature water to the domestic hot water system of a whole building or a section of a building.
Heatguard® 160 4 in1Thermostatic Mixing Valvefor Point-Of-Use with 4in 1 Service FittingsTemperature Range: 95-118°F, Flow Range: 1-11 gpm.Each is complete with service fittings on each inlet. The fittings have a 1/2" female inlet thread and connect to the base valve via union connections. The valve reduces the outlet flow to a trickle in the event of cold water supply failure. Every valve is tested for performance on an automated testing station prior to shipping. Accurate temperature control even under varying supply conditions. The Heatguard® 160 4 in 1 is intended to supply controlled temperature hot water to any outlet requiring a higher level of protection, such as a tub or basin in a nursing home or lavatory faucets in a public place.
Heatguard® 110-DSB
Heatguard® Series with Cabinet AssemblyThermostatic Master Controller with Cabinet for Commercial and Industrial ApplicationsTemperature Range: 95-150°F, Max Pressure: 145 psi.Fast acting, high quality thermostatic elements that sense the outlet temperature and react to maintain a stable delivery temperature even under varying and extremely low flows. The adjusting handle can be locked at a desired temperature. Each valve has integral mounting feet to allow it to be securely fixed
to a wall or frame. Complete with 4 in1 service fittings on each inlet. Every valve is factory tested. Each cabinet assembly is made to order. The robustly designed cabinet allows for secure safety, peace of mind. The Masterguard® Series features a range of six high flow rate Thermostatic Mixing Valves that mix hot water with cold water to deliver tempered water at a controlled temperature, typically 120°F (49°C). Intended for installation in the plant room of commercial and industrial facilities to distribute controlled temperature water to the domestic hot water system of a whole building or a whole section of building.
Heatguard® FittingsThermostatic MixingValve Fittings KitsFurnished with three union nuts and face seals. The kits contain three fittings of the selected type. Kits available in Sweat, Barb/PEX, Compression, Threaded (NPT), and CPVC (all kits are available with check). For use with Heatguard® thermostatic mixing valves. Sizes: Sweat - 1/2", 3/4" and 1" (checks not available for 1"), Barb/PEX - 1/2", 3/4" and 1", Compression - 1/2" and 3/4", Threaded - 1/2", 3/4", CPVC - 1/2" and 3/4", Compression with check - 3/8", 1/2", and 3/4".supply failure.
NEW!
TMV BrochureThe essential collection of Cash Acme’s HeatGuard® Thermostatic Mixing Valve range, including products connected by SharkBite®.
Single Access Port Checks & relief valve serviced from single portNon-Plugging Sensing Line Sensing line is from top of water way & can be purged with #2 test cockFlipable Check Valve Disks Checks & relief valve can be serviced without repair partsAll Top Access Design Test cocks, check valve, & relief valve have top access for tight installationsCommon Unitized Design All models & sizes have 1 common design, minimizing service trainingOnly 1 Model Revision in the Field Service part stock is minimalShort Laying Length Shortest laying length affords easy retrofitField Proven Design One design in the field for more than 10 yearsEasy Check Removal Either check can be removed without disturbing the otherNon-Plugging Relief Valve Guide Vent Bottom vented guide eliminates plugging and relief valve lockingSingle Repair Part Kit for DC & RP Only 9 rubber goods kits required to service complete lineNo Lead Models CA AB1953 & VA Compliant Units are Available3 Year Warranty Best Backed Backflow in the Business
CertificationsDouble Check Backflow Preventors Type DC100 and DC500 are CSA and ASSE 1015 listed and AWWA Compliant.
Reduced Pressure Zone Backflow Preventer Model RP100 and RP500 bronze and cast-iron are CSA and ASSE 1013 listed, AWWA Compliant C511 and all other major national approvals.
Pressure Vacuum Breakers PVB have all national approvals through the Danfoss Flowmatic and Conbraco brand names.
Feature Benefit
Reliance Worldwide USA2727 Paces Ferry Road SEBuilding Two, Suite 1800Atlanta, GA 30339Toll Free: 1-877-700-4242 Fax: 1-877-700-4280www.cashacme.com
Reliance Worldwide Canada74 Alex AvenueVaughan, Ontario, L4L 5X1Toll Free: 1-888-820-0120Fax: 1-888-820-0121www.cashacme.ca
Cash Acme products are manufactured and distributed by the Reliance Worldwide Corporation.
Backflow Preventer BrochureCash Acme continues to expand its product line with a complete offering of backflow prevention devices that make service easy and performance a given.