Post on 28-Sep-2020
Viale Vicenza, 14 - 36063 Marostica VI - Italy Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 Fax (Export) +39 0424 488 709www.vimar.com
1. CONCETTI BASE.
• Ogni linea può essere composta da un massimo di 128 dispositivi e necessita di 1 o 2 alimentatori, a seconda del numero di dispositivi e della lunghezza del bus.
• Tramite gli accoppiatori di linea 01845, opportunamente collegati e configurati, è possibile connettere più linee tra loro fino ad un massimo di 15 per ogni area.
• Numero massimo di aree = 15.
• In ogni centrale By-me possono essere configurati fino a 254 dispositivi di automazione oppure 194 dispositivi di automazione e 60 dispositivi antintrusione.
La configurazione del sistema prevede, come operazione iniziale, la creazione di gruppi funzionali; il gruppo funzionale è un insieme di dispositivi di comando e di attuazione associati ad una stessa funzione.In fase di installazione, dunque, la prima operazione da fare è ipotizzare le funzioni di cui si desidera disporre.
2. TOPOLOGIA INSTALLATIVA.
La caratteristica principale del sistema By-me è che tutti i dispositivi sono collegati tra loro da un cavo per sistemi bus (doppino) che fornisce agli stessi sia l’alimentazione che il segnale con i messaggi di comando e controllo. A fronte di ciò si dovranno utilizzare sempre i cavi art. 01840, 01840.Y e 01840.B.
Importante:In una linea dove è già stata configurata una centrale 21509 non è possibile configurare una seconda centrale (sia Eikon Evo 21509, sia Eikon 20550 o 14550 + 01960, sia centrali da parete che quelle a 2 moduli Eikon 20510 e 20480, Idea 16950 e 16930, Plana 14510 e 14480); in ogni linea quindi, può essere configurata una sola centrale.
In caso di integrazione tra il sistema di automazione e quello antintrusione, la centrale dovrà essere installata e configurata in “Area 00 - Linea 00” del sistema antintrusione; le linee automazione e antintrusione dovranno poi essere separate mediante un accoppiatore 01845.• Non è possibile interfacciare 2 centrali inizializzate entrambe con Area 00 Linea 00 e abilitate quindi alla gestione del sistema antiintrusione.• I valori di Area, Linea ed Offset di Gruppo inizialmente assegnati ad una centrale non possono poi essere modificati in un secondo momento.
SCHEMA DI COLLEGAMENTO con accoppiatore di separazione da un’altra linea di automazione.
230 V~
bus
LN
M
Setup
Indietro Esci
ImpostazioniConfigurazioneDiagnosticaInformazioni
230 V~
Comandi Centrale 21509 Rivelatore IR
Attuatorea relè
Comandicon attuatorea relè
Comandicon attuatoreper tapparelle
Alimentatore Linea 1
Alimentatore Linea 2
Accoppiatore di linea
Comandi
01401Alimentatore
(linea antintrusione)
BUS
29 V d.c. 230 V ~
+
-
20487 Rivelatore doppia tecn.
20485Rivelatore IR
20483Tastierino digitale
01804.01Unità di back-up
01803.01Unità di back-up ausiliaria
20490Interfaccia
contatti
21509Centrale 01820 - 01821
01822 - 0182301825-01826
Contatti
20493Interfaccia
per telecomandoe radiofrequenza
01806Sirena per esterno
01738Contatto magnetico
01744Rivelatore d'acqua
01942Comunicatoretelefonico GSM
Dispositivi sistema automazione
Dispositivi sistema automazione
BUS
AUX
230 V ~
01845Accoppiatore di linea
01401Alimentatore
(linea automazione)
AAA NiMH 1,2 V AAA NiMH 1,2 V
BUS+ -
12-30 V 12-24 V PROG
8
BUS 1
BU
S 2
01829.1Rivelatore
doppia tecnologia
Setup
Indietro Esci
ImpostazioniConfigurazioneDiagnosticaInformazioni
SCHEMA DI COLLEGAMENTO con accoppiatore di separazione tra l’impianto antintrusione e le linee di automazione.
2.1 Predisposizione impianto.
In fase di progettazione dell’impianto, è essenziale predisporre un centralino dimensionalmente capiente per alloggiare:
• i dispositivi tradizionali, magnetotermici, sezionamenti, ecc;
• 1 o 2 alimentatori di ingombro 8 moduli EN 50022;
• dispositivi per guida EN 50022 come il modulo di controllo carichi, il comunicatore GSM, le interfacce.
• eventuali unità di backup DIN con ingombro 6 moduli (art. 01807) e relativi supporti portabatterie DIN (art. 01809) con ingombro 12+12 moduli EN.
• limitatori di sovratensione a protezione dell’impianto.
Gli interfacciamenti tra più centrali appartenenti a linee differenti vanno accuratamente valutati sia dal punto di vista dei collegamenti che delle inizializzazioni delle centrali stesse (i valori di Area, Linea ed Offset di Gruppo vanno opportunamente impostati alla prima accensione).Questi interfacciamenti non permettono la condivisione dei dispositivi tra le centrali: i dispositivi collegati in una linea appartenente ad una centrale non possono essere configurati in un’altra centrale e non interagiranno quindi con l’impianto da essa gestito.L’unica interazione possibile tra centrali interfacciate sarà il richiamo simultaneo di alcuni scenari che verranno opportunamente creati come scenari “globali”.Un touch screen appositamente configurato e collegato in una delle linee potrà invece gestire anche gruppi e scenari di altre centrali ma non potrà controllare gli impianti di diffusione sonora (se presenti).
Nel caso di impianti costituiti da più linee e più centrali interfacciate, Vimar è vostra completa disposizione per valutare con voi la soluzione più ottimale; per qualsiasi informazione contattate la nostra rete di vendita o il Servizio Assistenza Clienti al numero verde 800.862.307.
Eikon Evo21509
49400427A0 03 1506VIMAR - Marostica - Italy
Linea 2
Linea 1
ALIMENTATORE
Fig. 3
• Per quanto riguarda i tubi corrugati per la posa del cavo Vimar 01840 della linea BUS, è consigliabile prevedere una canalina dedicata; è comunque possibile utilizzare quel-le dove passano i cavi della rete elettrica. Nel caso in cui siano presenti anche il sistema antintrusione e la diffusione sonora vanno utilizzati anche i cavi 01840.Y e 01840.B.
2.2 Lunghezza bus: regole generali.
• Lunghezza massima cavo bus: 1000 m.
• Distanza massima tra un alimentatore e dispositivo: 350 m.
• Posizione ottimale di ogni singolo alimentatore: al centro della linea BUS
• Distanza massima tra dispositivi: 700 m.
• Distanza minima tra 2 alimentatori o tra 2 unità di backup del sistema antintrusione: 40 m.
Il carico deve essere ben distribuito tra i due alimentatori; essi vanno posti ai capi in uno dei rami dell’impianto con il maggior numero di dispositivi o di diramazioni. La con-figurazione ottimale è quella con gli alimentatori posti più lontano possibile tra di loro.
• Posizione ottimale di due alimentatori: agli estremi della linea BUS
• Tensione minima sul dispositivo più lontano: 23 V d.c. (a riposo)
2.3 Messa in servizio del sistema.
1. Predisporre il cavo bus e i morsetti di collegamento prestando attenzione alla polarità.
2. Predisporre il cavo per gli eventuali collegamenti elettrici degli attuatori.
3. Cablare la centrale, i componenti e l’alimentatore.
4. Alimentare il sistema.
DISPOSITIVO
DISPOSITIVO DISPOSITIVO
DISPOSITIVO DISPOSITIVO
Morsetto di collegamento
Doppino twistato Vimar 01840
ALIMENTATORE ALIMENTATORE
ALIMENTATORE
Fig. 1
Fig. 2
• Il collegamento dei dispositivi può avvenire senza alcun ordine particolare, rispettando le polarità riportate sui morsetti. Sono possibili collegamenti di tipo lineare (fig. 1), a stella (fig. 2) o misti (fig. 3) La configurazione ideale è quella lineare con un solo alimentatore a metà impianto oppure con due alimentatori agli estremi del bus.Non chiudere anelli nel bus.
350 m
ALIMENTATORE
350 m 350 m
ALIMENTATORE
700 m
DISPOSITIVO DISPOSITIVO
250 m 250 m500 m
ALIMENTATORE ALIMENTATORE
Viale Vicenza, 14 - 36063 Marostica VI - Italy Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 Fax (Export) +39 0424 488 709www.vimar.com
230 V~
bus
LN
M
Setup
Indietro Esci
ImpostazioniConfigurazioneDiagnosticaInformazioni
230 V~
1. BASIC CONCEPTS
• Each line can be composed of at most 128 devices and needs one or two power supplies depending on the number of devices and the length of the bus.
• Using line couplers, a number of lines can be connected to each other, up to a maximum of 15 areas x 15 lines; the line couplers allow only authorized messages to pass between one line and another.
• Maximum of 15 areas.
• On each By-me control panel it is possible to configure up to 254 devices (194 automation devices and 60 intrusion detection alarm system devices).
System configuration starts with the creation of functional groups (it is better to think in terms of functional groups rather than individual devices), which is the only operation strictly necessary for the system to function. During the installation phase, the first operation is therefore to assume the functions that are to be made available.
2. INSTALLATION TOPOLOGY.
The main characteristic of the By-me system is that all devices are connected to each other by a bus system cable (pair) that supplies the devices with the power and the signals carrying the digital control and monitoring data.
The connecting cable, art. Vimar 01840, is the same as the one used in the burglar alarm bus system and Vimar bus entrance control system.
Warning:On a line where a control panel has already been configured (21509) it is not possible to configure a second control panel (either Eikon Evo 21509, Eikon 21550-20550 + 01960 or the Eikon 2-module control panels 20510 and 20480, Idea 16950 and 16930, Plana 14510 and 14480). The system is configured through the control unit and the configuration buttons located on the devices.
CONNECTION DIAGRAM with separation coupler from another automation line.
ControlsControl unit 21509 IR detector
Actuatorwith realy
Controlswith relayactuator
Controlswith actuatorfor rolling shutters
Power supply Line 1
Line coupler
Controls
CONNECTION DIAGRAM for the intrusion detection alarm system incorporated in the automa-tion system
2.1 System setup.
During the design phase, it is essential to arrange for a switchboard with sufficient capacity to hold:
• conventional devices, magneto-thermal protections, circuit-breakers, etc;
• 1 or 2 power supplies with capacity for 8 EN 50022 modules;
• EN 50022 rail devices such as the load control module, GSM communicator, interfaces.
• surge protection devices to protect the installation.
It is advisable to use a dedicate cable trough for the corrugated tubes that carry the Vimar 01840 cable for the Bus line; however, the ones that carry the mains power cables can also be used.
If integrating the automation and intrusion detection alarm systems, refer to the intrusion detection alarm system section in this manual that shows the connection diagram; in this case the control panel must be installed and configured in “Area 00 - Line 00” of the intrusion detection alarm system. The two automation and intrusion detection alarm system lines must then be separated with a coupler 01845.
Line 2
Line 1
Power supply Line 2
BUS
29 V d.c.
+
-
01845 ACCOPPIATORE DI LINEA
492.1845 0A 0404 VIMAR - Marostica - Italy
BUS 1BUS 2
01845Line Coupler
AAA NiMH 1,2 V AAA NiMH 1,2 V492.1942A0 0A
01942 COMUNICATORE GSM-BUS ON
GSM
BUS+ -
12-30 V 12-24 V
BUS
PROG492.1942A0 0A
492.1942A0 0A
8
BUS 1
BU
S 2
01804.01Back-up unit
01803.01Auxiliary back-up unit
01401Power supply
20483Digital keypad
01829.1Dual tech. detector20485
IR detector
20493Interface
for radio-frequencyremote control
20487Dual tech. detector
20490Contactinterface
01820-01821 01822-0182301825-01826
Contacts
01738Magneticcontact
01744Water
detector
01942GSM phonecommunicator
01806Siren for outdoor use
01401Power supply
Automation devices
Automation devices
230 V ~
230 V ~
21509Control unit
Setup
Indietro Esci
ImpostazioniConfigurazioneDiagnosticaInformazioni
Eikon Evo21509
POWER SUPPLY
Fig. 3
• For the connections use a VIMAR 01840 sheathed and twisted pair (2x0.5 mm2, nominal insulation voltage 300/500 V). The wire pair distributes both the power supply voltage (29 V d.c.) and the device control signals, and can be placed inside the same corrugated pipe that carries the electrical mains cables.
2.2 Bus length: general rules.• Maximum length of the bus cable: 1000 m.
• Maximum distance between power supply and device: 350 m.
• Optimum position of each power supply: at the centre of the BUS line.
• Maximum distance between two devices: 700 m.
• Minimum distance between two power supplies: 40 m (loads must be balanced between the two power supplies).
It is important for the load to be well distributed between the two power supplies; the two power supplies should be placed at the ends of the one of the circuits of the system that has the largest number of devices or branches.
• Optimum position of two power supplies: at the ends of the BUS line
• Minimum voltage on the furthest device: 23 V d.c. (at rest)
2.3 Putting the system into service.
1. Lay out the bus cable and connecting terminals, maintaining the correct polarities.
2. Lay out the cable for the electrical connections of the actuators.
3. Wire the control panel, components and power supply.
4. Power up the system.
DEVICE
DEVICE DEVICE
DEVICE DEVICE
Connection terminal
Vimar 01840 twisted pair
POWER SUPPLY POWER SUPPLY
POWER SUPPLY
Fig. 1
Fig. 2
• The devices do not have to be connected in any particular order, maintaining the polarities indicated on the terminals. Linear type connections (figure 1), star type connections (figure 2) or mixed connections (figure 3) are possible (the rectangle in the figures represents the power supply). The ideal configuration is the linear type with only one power supply in the middle of the system, or two power supplies at the ends of the bus cable.
350 m
POWER SUPPLY
350 m 350 m
POWER SUPPLY
700 m
DEVICE DEVICE
250 m 250 m500 m
POWER SUPPLY POWER SUPPLY
Viale Vicenza, 14 - 36063 Marostica VI - Italy Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 Fax (Export) +39 0424 488 709www.vimar.com
230 V~
bus
LN
M
Setup
Indietro Esci
ImpostazioniConfigurazioneDiagnosticaInformazioni
230 V~
1. CONCEPTS BASE.
• Chaque ligne se compose de 128 dispositifs maximum et nécessite un ou deux alimentateurs en fonction du nombre de dispositifs et de la longueur du bus.
• Par les coupleurs de ligne, il est possible de relier plusieurs lignes entre elles pour un maximum de 15 zones x 15 lignes ; les coupleurs permettent le transit entre les lignes des seuls messages autorisés.
• Maximum de 15 zones
• Dans chaque centrale By-me, il est possible de configurer jusqu'à 254 dispositifs (194 dispositifs d'automation et 60 dispositifs anti-intrusion).
La configuration du système prévoit comme opération initiale la création de groupes fonctionnels (il convient de raisonner en termes de groupes fonctionnels plutôt que de dispositifs d'une installation), seule opération strictement nécessaire pour le fonctionnement du système. En phase d'installation la première chose à faire est de supposer les fonctions désirées.
2. TOPOLOGIE D’INSTALLATION.
La caractéristique principale du systèmeBy-me est que tous les dispositifs sont reliés entre eux par un câble pour systèmes bus (boucle) qui transmet à ceux-ci l’alimentation et le signal avec les messages numériques de commande et de contrôle.
Le câble de liaison art. Vimar 01840 est le câble utilisé sur les systèmes anti-intrusion via bus et le contrôle des accès via bus Vimar.
Attention :Dans une ligne dans laquelle un centrale a été configurée (21509), il n'est pas possible de configurer une seconde centrale (tant Eikon Evo 21509, Eikon 21550-20550 + 01960 que les centrales à 2 modules Eikon 20510 et 20480, Idea 16950 et 16930, Plana 14510 et 14480).
SCHÉMA DE CONNEXION avec coupleur de séparation d'une autre ligne d'automation.
Central de contrôle 21509
SCHÉMA DE CONNEXION système anti-intrusion intégré dans le système d'automation
2.1 Prédisposition installation.
En phase de conception, prévoir une centrale suffisante pour contenir :
• les dispositifs traditionnels, magnétothermiques, sectionneurs etc. ;
• 1 ou 2 alimentateurs d'encombrement 8 modules EN 50022 ;
• des dispositifs de guidage EN 50022 comme le module de contrôle des charges, le communicateur GSM, les interfaces.
• des limiteurs de tension de protection de l'installation.
Pour les tuyaux annelés de pose du câble Vimar 01840 de la ligne BUS, il est conseillé de prévoir une goulotte dédiée ; il est dans tous les cas possible d'utiliser celles dans lesquelles passent les câbles du réseau électrique.
En cas d'intégration entre le système d'automation et celui anti-intrusion, consulter la section anti-intrusion du manuel qui contient le schéma de connexion; dans ce cas, la centrale devra être installée et configurée en “Zone 00 - Ligne 00” du système anti-intrusion. Les deux lignes automation et anti-intrusion devront ensuite être séparées au moyen d'un coupleur 01845.
Commandes Détecteur IR
Actionneurà relais
Commandesavec actionneur
à relais
Commandesavec actionneur
pour volets
Alimentateur Ligne 1
Alimentateur Ligne 2
Coupleurs de ligne
Commandes
BUS
29 V d.c.
+
-
01845 ACCOPPIATORE DI LINEA
492.1845 0A 0404 VIMAR - Marostica - Italy
BUS 1BUS 2
01845Coupleurs de ligne
AAA NiMH 1,2 V AAA NiMH 1,2 V492.1942A0 0A
01942 COMUNICATORE GSM-BUS ON
GSM
BUS+ -
12-30 V 12-24 V
BUS
PROG492.1942A0 0A
492.1942A0 0A
8
BUS 1
BU
S 2
20483Pavé numérique
01820-01821 01822-0182301825-01826
Contacts
Dispositifs d’automation
01804.01Unité de back-up
01803.01Unité de back-up auxiliaire
01401Alimentateur
01401Alimentateur
01829.1Détecteur
Double techn.20485Détecteur IR
20490Interfacecontacts
20493Interface pourtélécommande
et radiofréquence
01738Contact
magnétique
01744Révélateur
d’eau
01942Communicateurtéléphonique GSM
20487Détecteur
Double techn.
01806Sirène externe
Dispositifs d’automation
230 V ~
230 V ~
21509Central de contrôle
Setup
Indietro Esci
ImpostazioniConfigurazioneDiagnosticaInformazioni
Eikon Evo21509
Ligne 2
Ligne 1
ALIMENTATEUR
Fig. 3
• Pour les connexions, utiliser le double câble torsadé et gainé VIMAR 01840 (2x0,5 mm², tension nominale d'isolation 300/500 V). Le câble distribue la tension d'alimentation (29 V c.c.) et les signaux de contrôle et de gestion des dispositifs, et peut être inséré dans le même tuyau annelé de passage des câblages électriques.
2.2 Longueur bus : règles générales.• Longueur maximum totale de la ligne bus : 1.000 m
• Distance maximum entre alimentateur et dernier dispositif : 350 m
• Position optimale de chaque alimentateur : au centre de la ligne BUS
• Distance maximale entre deux dispositifs : 700 m
• Distance minimum entre deux alimentateurs : 40 m (les charges doivent être équilibrées entre les 2 alimentateurs)
La charge doit être bien distribuée entre les 2 alimentateurs; les 2 alimentateurs doivent être positionnés aux extrémités sur la branche de l'installation qui possède le plus grand nombre de dispositifs ou de dérivations.
• Position optimale de 2 alimentateurs : aux extrémités de la ligne BUS
• Tension minimum sur le dispositif le plus éloigné : 23 V c.c. (au repos)
2.3 Mise en service du système.
1. Préparer le câble bus et les bornes de connexion en faisant attention à la polarité.
2. Préparer le câble pour les connexions électriques éventuelles des actionneurs.
3. Câbler la centrale, les composants et l’alimentateur.
4. Alimenter le système.
DISPOSITIF
DISPOSITIF DISPOSITIF
DISPOSITIF DISPOSITIF
Borne de raccordement
Double câble torsadé Vimar 01840
ALIMENTATEUR ALIMENTATEUR
ALIMENTATEUR
Fig. 1
Fig. 2
• Le branchement des dispositifs peut se faire sans ordre particulier, en respectant les polarité des bornes. Il est possible d'effectuer des branchements de type linéaire (figure 1), en étoile (figure 2) ou mixtes (figure 3) (sur les figures, le rectangle représente l'alimentateur). La configuration idéale est linéaire avec un seul alimentateur à mi-installation ou deux alimentateurs aux extrémités du câble bus.
350 m
ALIMENTATEUR
350 m 350 m
ALIMENTATEUR
700 m
DISPOSITIF DISPOSITIF
250 m 250 m500 m
ALIMENTATEUR ALIMENTATEUR