Post on 07-Jan-2017
Edition 2016-02
EC centrifugal fans - RadiPac
The ebm-papst RadiPac EC centrifugal fan series is more efficient than
ever.
This was achieved by the logical advanced development of the aero-
dynamics and motor technology.
While materials of higher quality were used in the motors to reduce
internal losses, the centrifugal impeller has undergone an entirely
new development!
Furthermore, the installation situation preferred later in air handling units
was already given proper consideration in the design of the blade channel.
This has a tremendous effect on the energy balance during operation and
results in drastic energy savings....
In the future, sizes 250 and 280 will be made of high-strength composite
material. For sizes 310 to 560, we will continue to use sheet aluminum,
with the difference being that the blade with a hollow profile achieves the
greatest stability and the design produces the best aeroacoustic proper-
ties.
Sizes 630 to 900 are still produced with our proven aerodynamics.
But the new aerodynamics technology will soon be available for
these sizes as well.
The new RadiPac fans are characterized especially
by the following points:
Best overall efficiency
Comfortable noise level
Compact design
Consistent series
Fast availability
Easy startup (uncomplicated configuration of the control electronics)
Well coordinated system (preconfigured motor / control electronics / impeller system)
Logistic advantages due to complete unit
EC motor without rare earth magnets
Production selection software is available on request to help you make
a convenient and quick selection, calculate the lifecycle costs, and to
compare products.
Additional information on the subjects of efficiency, dependability, and
commitment is available in special editions 1 and 2 of the special
techmag publications.
RadiPac: Now even better!
2
2016
-02
RadiPac 630 54RadiPac 710 58RadiPac 800 62RadiPac 900 66RadiPac 280 - 450 (compact design) 70Technology:
- Tender specifi cations 74 - Accessories 79 - Conn. diagrams 91 - Technical parameters & scope 98ebm-papst agents 102
RadiPac: Now even better! 2About ebm-papst. 4Overview of products 6Overview of curves 8RadiPac 250 12RadiPac 280 18RadiPac 310 24RadiPac 355 30RadiPac 400 36RadiPac 450 40RadiPac 500 46RadiPac 560 50
3
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
Contents
4
2016
-02
About ebm-papst.
As a leader in technologies for ventilation and drive engineering, ebm-papst is in demand as an engineering partner in many sectors. With over 15,000 different products, we provide the right solution for just about any challenge. Our fans and drives are reliable, quiet and energy-efficient.
Six reasons that make us the ideal partner:
Our systems expertise.You want the best solution for every project. The inter relationships
between ventilation and drive engineering must thus be considered
as a whole. And thats what we do with motor technology that sets standards, sophisticated electronics and aerodynamic designs all from a single source and perfectly matched. These system solutions
release unique synergies worldwide. And in particular they relieve you
of a lot of work, so that you can concentrate on your core competency.
The ebm-papst spirit of invention.In addition to our wide range of products, we are always able to develop
customized solutions for you. A diversified team of 600 engineers and
technicians works at our three locations in Germany: Mulfingen, Landshut
and St. Georgen. Contact us to discuss your next project.
Our lead in technology.As pioneer and trail-blazer for developing highly efficient EC tech nology,
we are way ahead of other motor manufacturers. Almost our entire product
range is also available with GreenTech EC technology. The list of benefits is
long: higher efficiency, main tenance-free, longer service life, sound reduc-
tion, intelligent control characteristics and incomparable energy efficiency
with savings of up to 80 % compared to conventional AC technology. Let
our technology be your competitive advantage as you lead in your industry.
Proximity to our customers.ebm-papst owns 57 sales offices worldwide, of which 47 are sub sidiaries
with an extensive network of sales representatives and distributors. You
will always have a local contact, someone who speaks your language and
knows your market.
Our standard of quality.Of course you can rely on the highest standards of quality with our pro-
ducts. Our quality management is uncompromising, at every step in every
process. This is underscored by our certification according to international
standards including DIN EN ISO 9001, ISO/TS 16949-2 and DIN EN ISO
14001.
Our sustainable approach.Assuming responsibility for the environment, for our employees and for
society is an integral part of our corporate philosophy. We develop
products with an eye to maximum environmental compatibility, in particu-
lar resource-preserving production methods. We promote environmental
awareness among our young staff and are actively involved in sporting,
cultural activities and education. Thats what makes us a leading company
and an ideal partner for you.
The story of our success to market and technology pioneer.
5
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
1963 Founding of Elektrobau Mulfingen GmbH & Co. KG by Gerhard Sturm and Heinz Ziehl.
1965 First tubeaxial fan developed in EC/DC technology.
1966 ebm-papsts success takes off with the new 68 motor.
1972 The first ebm-papst foreign subsidiary is established in Sweden.
1988 Gerhard Sturm is awarded the Federal Cross of Merit.
1990 The sixty-millionth external-rotor fan is produced.
1992 Acquisition of PAPST Motoren GmbH in St. Georgen.
1997 Buyout of the Landshut (mvl) plant.
1998 Development of first fans with integrated electronics.
2003 Change of name to ebm-papst.
2008 The HyBlade range of fans sets new efficiency standards.
2010 GreenTech our sign for energy efficiency and resource preservation.
2011 RadiCal defines a new standard for EC centrifugal fans.
2013 ebm-papst takes over the gearbox specialist Zeitlauf and wins the German Sustainability Award.
2014 Team partnership with Mercedes AMG PETRONAS Formula 1 team.
2015 RadiPac pushes the limits of efficiency.
Product overview RadiPac
Data is subject to change without notice at ebm-papst discretion.
M3G 084-DF 1~200-277
M3G 084-DF 1~200-277250
R3G 250-PR04 -H1 K3G 250-PR04 -H2 ---
R3G 250-PR17 -I1 K3G 250-PR17 -I2 --- 12
Motor
NominalvoltagerangeVAC
Centrifugal fanCentrifugal modulewith support bracket
Centrifugal modulewith cube design
Pageff.
6
2016
-02
M3G 084-DF 3~380-480 R3G 250-PR02 -J1 K3G 250-PR02 -J2 ---
M3G 084-DF 1~200-277
M3G 084-DF 1~200-277280
R3G 280-PR03 -H1 K3G 280-PR03 -H2 ---
R3G 280-PR04 -I1 K3G 280-PR04 -I2 --- 18
M3G 084-FA 3~380-480 R3G 280-PS10 -J1 K3G 280-PS10 -J2 ---
M3G 084-GF 3~380-480
M3G 112-GA 3~380-480310
R3G 310-PT08 -J1 K3G 310-PT08 -J2 ---
R3G 310-PH38 -01 K3G 310-PH38 -02 --- 24
M3G 112-GA 3~380-480 R3G 310-PH58 -01 K3G 310-PH58 -02 ---
M3G 112-EA 3~380-480
M3G 112-GA 3~380-480355
R3G 355-PJ75 -01 K3G 355-PJ75 -01 ---
R3G 355-PH49 -01 K3G 355-PH49 -02 --- 30
M3G 112-IA 3~380-480 R3G 355-PI93 -01 K3G 355-PI93 -02 ---
M3G 112-IA 3~380-480
M3G 150-FF 3~380-480400
R3G 400-PI92 -01 K3G 400-PI92 -02 ---
R3G 400-PA27 -71 K3G 400-PA27 -71 ---36
M3G 112-IA 3~380-480
M3G 150-FF 3~380-480450
R3G 450-PI86 -01 K3G 450-PI86 -02 ---
R3G 450-PA23 -71 K3G 450-PA23 -71 --- 40
M3G 150-IF 3~380-480 R3G 450-PB24 -01 K3G 450-PB24 -01 ---
M3G 150-FF 3~380-480
M3G 150-IF 3~380-480500
R3G 500-PA23 -71 K3G 500-PA23 -71 ---
R3G 500-PB33 -01 K3G 500-PB33 -01 ---46
M3G 150-IF 3~380-480
M3G 150-NA 3~380-480560
R3G 560-PB31 -71 K3G 560-PB31 -71 ---
R3G 560-PC04 -01 K3G 560-PC04 -01 ---50
RadiPac: The best solution
0,50
0,75
Max.inputpower
kW
1,18
0,50
0,75
1,05
1,23
1,80
2,95
1,10
1,90
2,68
2,50
3,35
1,74
2,90
5,25
3,45
5,70
3,30
5,00
Example:R3G .....
Example:K3G .....
7
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
Product overview RadiPac
M3G 150-NA 3~380-480
M3G 200-HF 3~380-480630
R3G 630-AP01 -01 K3G 630-AP01 -01 ---
--- --- K3G 630-AR02 -01 54
Motor
M3G 200-QA 3~380-480 --- --- K3G 630-AS05 -01
M3G 150-NA 3~380-480
M3G 200-LA 3~380-480710
R3G 710-AP02 -01 K3G 710-AP02 -01 ---
--- --- K3G 710-AR03 -01 58
M3G 200-QA 3~380-480 --- --- K3G 710-AS06 -01
M3G 200-QA 3~380-480
M3G 200-QA 3~380-480800
--- --- K3G 800-AR08 -01
--- --- K3G 800-AS07 -0162
M3G 200-QA 3~380-480
M3G 200-QA 3~380-480900
--- --- K3G 900-AR10 -01
--- --- K3G 900-AS08 -0166
M3G 084-GF 3~380-480
M3G 112-GA 3~380-480
280 R3G 280-AJ14 -C1 --- ---
R3G 310-BC38 -01 --- ---
70
Motor
M3G 112-GA 3~380-480 R3G 355-BD43 -01 --- ---
M3G 150-FF 3~380-480
M3G 150-FF 3~380-480
R3G 400-AS23 -01 --- ---
R3G 450-AS24 -01 --- ---
310
355
400
450
RadiPac: The powerful solution
RadiPac: The compact solution
Com
pact
des
ign
Tech
nolo
gyAg
ents
2,90
6,75
11,00
2,80
7,86
11,80
7,53
11,60
7,52
8,70
0,99
1,65
1,73
2,84
2,38
NominalvoltagerangeVAC
Centrifugal fan(compact design)
Centrifugal modulewith support bracket
Centrifugal modulewith cube design
Pageff.
Max.inputpower
kW
NominalvoltagerangeVAC
Centrifugal fanCentrifugal modulewith support bracket
Centrifugal modulewith cube design
Pageff.
Max.inputpower
kW
Example:R3G .....
Example:K3G .....
Example:R3G .....
Overview of curves RadiPac
50002500 7500 10000 12500 15000 17500
qv m/h25000 30000100005000 15000 20000
P fs
Pa
500
1000
8.0
6.0
4.0
2.0
in w
g
cfm
1500
2000
250
750
7.0
5.0
3.0
1.0
1250
1750
400
310
500
250
710
450
900
560
630
800
355
280
8
2016
-02
The graph shows the maximum air performance for each size. If less performance is required, variants with smaller motors can be used.
This saves additional costs. The right fan for every application!
RadiPac in the Product Selector
To aid in selection of the right fan, ebm-papst provides the
"Product Selector" software with an integrated "Black-Box" module
for incorporation in customer device configuration programs.
With this new program, you can use the operating point as a selection
criterion for RadiPac fans.
If there is more than one fan in the specified power range, the displayed
aerodynamic and acoustic data can be used to select and document the
most suitable fan.
The difference between the measurements and the data published in the
"Product Selector" software was tested by TV SD and the accuracy of
the calculation was assigned to class B0.
You can also have the life cycle costs calculated for the selected fans.
You can make your selection based on point of operation or type
designation.
Data sheets can be created in PDF format and show not only a fans
nominal data but also its performance data at the specified operating
point together with the intake and outlet sound power levels over the
octave band.
Just ask your contact at ebm-papst!
9
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
10
2016
-02
EC centrifugal fans RadiPac
11
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
12
2016
-02
EC centrifugal fans RadiPacbackward curved, 250
Curves:
qv m/h
cfmP fs
Pa in w
g
500 1000 1500 2000 2500 3000 3500
0 400 800 1200 1600 2000
400
800
1200
12
34
56
11
3
3
3
4
4
4
1
22
2
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Subject to change
Type Motor
*3G 250 M3G 084-DF P. 94 / P5)
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
*3G 250 M3G 084-DF P. 94 / P5)
VAC Hz rpm kW A C kg
1~200-277 50/60 3080 0,50 2,30 -25..+40 4,2
Curv
e
A
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p. 1~200-277 50/60 3450 0,75 3,30 -25..+40 4,6B
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: PP plastic Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 6 Direction of rotation: Clockwise viewed toward rotor Degree of protection: IP 55 Insulation class: "F" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
*3G 250 M3G 084-DF P. 95 / P6) 3~380-480 50/60 4000 1,18 1,80 -25..+40 4,5C
nrpm
PedkW
IA
LWAdB(A)
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
3375
3135
3080
3200
3605
3505
3450
3525
4000
4000
4000
4000
0,49
0,50
0,50
0,50
0,62
0,73
0,75
0,73
0,86
1,13
1,18
1,11
2,12
2,30
2,30
2,30
2,71
3,20
3,30
3,17
1,34
1,75
1,80
1,71
89
79
75
79
91
83
77
81
91
85
83
86
(1) Nominal data at operating point with maximum load and 230 or 400 VAC.
= max.3
B
C
A
13
I
nfor
mat
ion
25
0
280
71
0
800
90
0
2016
-02
Technical features: See connection diagram P. 94 f. Touch current:
14
2016
-02
EC centrifugal fans RadiPacbackward curved, 250
R3G 250-PR04-H1 (Centrifugal fan)
K3G 250-PR04-H2 (Centrifugal module with support bracket)
116.8
152.51.8
1640.35
M6 (4x)
4x90
45
85
10
1000
+20
8
150
0.
35
172
.5
0.3
270
178
47.7
10
48
280
11
(4x)
298
234.73
85108
1000 +20
18722
10
1.5350400
Max. clearance for screw 16 mm
Cable PVC AWG22,5x crimped ferrules
Accessory part: Inlet ring 96355-2-4013Not included in scope of delivery (k-factor: 76)Dimensions: see Accessories chapter
Attachment for inlet ring and FlowGrid (4x)
Cable PVC AWG18,5x crimped ferrules
Pressure tap (k-factor: 76)
15
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 250-PR17-I1 (Centrifugal fan)
K3G 250-PR17-I2 (Centrifugal module with support bracket)
116.8
10
152.51.8
1860.5
M6 (4x)
4x90
45
85
10
1000
+20
8
169
0.
35
172
.5
0.3
270
200
64.1
48
280
11
(4x)
298
251.13
85108
1000 +20
18722
10
1.5350400
Max. clearance for screw 16 mm
Cable PVC AWG22,5x crimped ferrules
Accessory part: Inlet ring 96355-2-4013Not included in scope of delivery (k-factor: 76)Dimensions: see Accessories chapter
Cable PVC AWG18,5x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 76)
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 250
16
2016
-02
R3G 250-PR02-J1 (Centrifugal fan)
K3G 250-PR02-J2 (Centrifugal module with support bracket)
116.8
10
152.51.8
1860.5
M6 (4x)
4x90
45
85
10
1000
+20
8
169
0.
35
172
.5
0.3
270
200
64.1
48
280
11
(4x)
298
251.13
85108
1000 +20
18722
10
1.5350400
Max. clearance for screw 16 mm
Cable PVC AWG22,5x crimped ferrules
Accessory part: Inlet ring 96355-2-4013Not included in scope of delivery (k-factor: 76)Dimensions: see Accessories chapter
Cable PVC AWG18,6x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 76)
EC centrifugal fans RadiPacbackward curved, 250
17
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
18
2016
-02
qv m/h
cfmP fs
Pa
in w
g
1000 2000 3000 4000
0 400 800 1200 1600 2000
400
800
1200
12
34
5
1 1 1
2
3
4
2
3
4
2
3
4
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
2990
2785
2670
2835
3260
3115
3000
3180
3400
3400
3400
3400
0,50
0,50
0,50
0,50
0,64
0,73
0,75
0,72
0,74
0,96
1,05
0,93
2,18
2,30
2,30
2,30
2,81
3,18
3,30
3,15
1,17
149
160
143
87
80
74
78
87
82
77
82
88
83
80
85
= max.3
*3G 280 M3G 084-DF P. 94 / P5)
*3G 280 M3G 084-DF P. 94 / P5)
1~200-277 50/60 2670 0,50 2,30 -25..+45 4,2A
1~200-277 50/60 3000 0,75 3,30 -25..+45 4,9B
*3G 280 M3G 084-FA P. 95 / P6) 3~380-480 50/60 3400 1,05 1,60 -25..+45 5,4C
B
C
A
EC centrifugal fans RadiPacbackward curved, 280
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: PP plastic Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 6 Direction of rotation: Clockwise viewed toward rotor Degree of protection: IP 55 Insulation class: "F" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
nrpm
PedkW
IA
LWAdB(A)
Subject to change (1) Nominal data at operating point with maximum load and 230 or 400 VAC.
Type Motor
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
19
I
nfor
mat
ion
25
0
280
31
0
710
80
0
900
2016
-02
Technical features: See connection diagram P. 94 f. EMC: A B Interference emission according to EN 61000-6-3 C Interference emission according to EN 61000-6-3, except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW A B C Immunity to interference according to EN 61000-6-2 A B Circuit feedback according to EN 61000-3-2/3 Touch current:
20
2016
-02
R3G 280-PR03-H1 (Centrifugal fan)
K3G 280-PR03-H2 (Centrifugal module with support bracket)
12746
8
1601.8
1640.35
M6 (4x)
4x90
45
85
10
1000
+20
8
150
0.
35
187
.5
0.3
294
280
178
47.7
11
(4x)
298
242.23
85108
1000 +20
194.522
10
1.25350400
Max. clearance for screw 16 mm
Cable PVC AWG22,5x crimped ferrules
Accessory part: Inlet ring 28004-2-4013Not included in scope of delivery (k-factor: 77)Dimensions: see Accessories chapter
Cable PVC AWG18,5x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 77)
EC centrifugal fans RadiPacbackward curved, 280
21
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 280-PR04-I1 (Centrifugal fan)
K3G 280-PR04-I2 (Centrifugal module with support bracket)
127 46
8
1601.8
1860.5
M6 (4x)
4x90
45
85
10
1000
+20
8
169
0.
35
187
.5
0.3
294
280
200
64.1
11
(4x)
298
258.63
85108
1000 +20
194.522
10
1.25
350400
Max. clearance for screw 16 mm
Cable PVC AWG22,5x crimped ferrules
Accessory part: Inlet ring 28004-2-4013Not included in scope of delivery (k-factor: 77)Dimensions: see Accessories chapter
Cable PVC AWG18,5x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 77)
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 280
22
2016
-02
R3G 280-PS10-J1 (Centrifugal fan)
K3G 280-PS10-J2 (Centrifugal module with support bracket)
127 46
8
1751.8
1860.5
M6 (4x)
4x90
45
85
10
1000
+20
8
169
0.
35
187
.5
0.3
294
280
200
64.1
11
(4x)
298
273.63
85108
1000 +20
209.522
10
1.25350400
Max. clearance for screw 16 mm
Cable PVC AWG22,5x crimped ferrules
Accessory part: Inlet ring 28004-2-4013Not included in scope of delivery (k-factor: 77)Dimensions: see Accessories chapter
Cable PVC AWG18,6x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 77)
EC centrifugal fans RadiPacbackward curved, 280
23
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
24
2016
-02
qv m/h
cfmP fs
Pa
in w
g
1000 2000 3000 4000 5000 6000 7000
0 1000 2000 3000 4000
500
1000
1500
2000
24
68
2
3
4
2
3
4
2
3
4
111
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: Sheet aluminium Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 5 Direction of rotation: Clockwise viewed toward rotor Degree of protection: A IP 55; B C IP 54 Insulation class: A "F"; B C "B" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
3010
3010
3010
3010
3410
3410
3410
3410
4000
4000
4000
4000
0,67
1,05
1,23
1,19
1,05
1,54
1,80
1,75
1,41
2,61
2,94
2,95
1,06
1,61
1,90
1,82
1,68
2,40
2,80
2,69
2,66
4,03
4,53
4,60
92
84
78
85
93
86
83
87
102
92
89
92
= max.3
*3G 310 M3G 084-GF P. 96 / P8)
*3G 310 M3G 112-GA P. 92 / M3)
3~380-480 50/60 3010 1,23 1,90 -25..+40 7,0A
3~380-480 50/60 3410 1,80 2,80 -25..+40 10,9B
*3G 310 M3G 112-GA P. 92 / M3) 3~380-480 50/60 4000 2,95 4,60 -25..+40 10,9C
C
B
A
EC centrifugal fans RadiPacbackward curved, 310
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
nrpm
PedkW
IA
LWAdB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
25
I
nfor
mat
ion
25
0
280
31
0
710
80
0
900
2016
-02
Technical features: See connection diagram P. 92 f. EMC: Interference emission according to EN 61000-6-3, except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW Immunity to interference according to EN 61000-6-2 Touch current:
26
2016
-02
R3G 310-PT08-J1 (Centrifugal fan)
K3G 310-PT08-J2 (Centrifugal module with support bracket)
98.2
179
6
1860.5
255.51.8
169
0.
35
M6 (4x)
4x90
45
223
.5+
1
360
200
108.5
54.8
350
11
(4x)
372
M20x1.5 M16x1.5 (2x)
4.5 (x4)
408.53
2903002.5
15
4x9045
450
500
Tightening torque1.5 0.2 Nm
Cable glandM20 x 1.5: Cable diametermin. 8 mm, max. 12 mmTightening torque 2.5 0.4 Nm
Max. clearance for screw 16 mmAccessory part: Inlet ring 31475-2-4013Not included in scope of delivery (k-factor: 116)Dimensions: see Accessories chapter
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 116)
Cable glandM16 x 1.5 (2x):Cable diametermin. 6 mm, max. 10 mmTightening torque 2.5 0.4 NmCable diametermin. 4 mm, max. 7 mmTightening torque 2.5 0.4 Nm(included seal must be used)
EC centrifugal fans RadiPacbackward curved, 310
27
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 310-PH38-01 (Centrifugal fan)
K3G 310-PH38-02 (Centrifugal module with support bracket)
98.2
179
251
6
2520.5
275
M10 (6x)
6x60
360
232
72
223
.5+
1
54.8
350
11
(4x)
375
M20x1.5 (3x)
4.5 (x4)
367,53
290295.52.5
15
4x9045
450
500Attachment for FlowGrid (4x)
Pressure tap (k-factor: 116)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 31475-2-4013Not included in scope of delivery (k-factor: 116)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 310
28
2016
-02
R3G 310-PH58-01 (Centrifugal fan)
K3G 310-PH58-02 (Centrifugal module with support bracket)
98.2
179
251
6
2520.5
275
M10 (6x)
6x60
360
72
223
.5+
1
54.8
350
11
(4x)
375
4.5 (x4)
367.53295.51
15
4x9045
450
500
290
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 116)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 31475-2-4013Not included in scope of delivery (k-factor: 116)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 310
29
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
30
2016
-02
qv m/h
cfmP fs
Pa
in w
g
2000 4000 6000 8000
0 1000 2000 3000 4000
400
800
1200
1600
24
6
1 11 1
2
3
4
2
3
4
2
3
4
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
2400
2400
2400
2400
2870
2870
2870
2870
3230
3230
3230
3230
0,62
0,97
1,10
1,07
1,05
1,58
1,90
1,89
1,48
2,16
2,68
2,56
0,98
1,49
1,70
1,65
1,69
2,46
3,00
2,92
2,30
3,32
4,10
3,94
87
78
76
80
92
85
81
86
93
87
83
87
= max.3
*3G 355 M3G 112-EA P. 96 / P8)
*3G 355 M3G 112-GA P. 92 / M3)
3~380-480 50/60 2400 1,10 1,70 -25..+40 8,7A
3~380-480 50/60 2870 1,90 3,00 -25..+40 13,0B
*3G 355 M3G 112-IA P. 92 / M3) 3~380-480 50/60 3230 2,68 4,10 -25..+40 15,0C
B
C
A
EC centrifugal fans RadiPacbackward curved, 355
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: Sheet aluminium Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 5 Direction of rotation: Clockwise viewed toward rotor Degree of protection: A IP 55; B C IP 54 Insulation class: A "F"; B C "B" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
nrpm
PedkW
IA
LWAdB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
31
I
nfor
mat
ion
25
0
280
71
0
800
90
0
2016
-02
R3G 355-PJ75 -01
R3G 355-PH49 -01
8,7
13,0
16,4
23,0
35675-2-4013
35675-2-4013
R3G 355-PI93 -01 15,0 26,035675-2-4013
K3G 355-PJ75 -01
K3G 355-PH49 -02
K3G 355-PI93 -02
31
0
630
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
Conn. diagramP. 92 f.
Inlet ringP. 82 ff.
DrawingsP. 32 ff.
Centrifugal fan kg kg
Wei
ght
cent
rifug
al fa
n
Technical features: See connection diagram P. 92 f. EMC: Interference emission according to EN 61000-6-3, except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW Immunity to interference according to EN 61000-6-2 Touch current:
32
2016
-02
R3G 355-PJ75-01 (Centrifugal fan)
K3G 355-PJ75-01 (Centrifugal module with support bracket)
6
252,52
1860.5200
M6 (4x)
4x90
45
252
.5+
1
405
169
100.5
110.5199.7
64.43
70
11
(4x)
414
4x9
345
4063305.52
15
4x9045
450
500
Tightening torque1.5 0.2 Nm
Cable glandM20 x 1.5: Cable diametermin. 8 mm, max. 12 mmTightening torque 2.5 0.4 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 35675-2-4013Not included in scope of delivery (k-factor: 148)Dimensions: see Accessories chapter
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 148)
Cable glandM16 x 1.5 (2x):Cable diametermin. 6 mm, max. 10 mmTightening torque 2.5 0.4 NmCable diametermin. 4 mm, max. 7 mmTightening torque 2.5 0.4 Nm(included seal must be used)
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 355
33
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 355-PH49-01 (Centrifugal fan)
K3G 355-PH49-02 (Centrifugal module with support bracket)
6
252
2722 275
M10 (6x)
6x60
4052
32
252
.5
110.5
199.7
72
64.43
70
11
(4x)
417
4x9
345
397,53325.52
15
4x9045
450
500
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 148)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 35675-2-4013Not included in scope of delivery (k-factor: 148)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 355
34
2016
-02
R3G 355-PI93-01 (Centrifugal fan)
K3G 355-PI93-02 (Centrifugal module with support bracket)
252
.5+
1
110.5
199.7
6
2922
2520.5275
M10 (6x)
6x60
405
232
72
64.43
70
11
(4x)
417
4x9
345
417.53345.52
15
4x9045
450
500
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 148)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 35675-2-4013Not included in scope of delivery (k-factor: 148)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 355
35
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
36
2016
-02
qv m/h
cfmP fs
Pa
in w
g
2000 4000 6000 8000 10000
0 1000 2000 3000 4000 5000 6000
400
800
1200
1600
24
6
11
2
3
4
2
3
4
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: Sheet aluminium Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 5 Direction of rotation: Clockwise viewed toward rotor Degree of protection: A IP 54; B IP 55 Insulation class: A "B"; B "F" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
2450
2450
2450
2450
2750
2750
2750
2750
1,32
2,21
2,50
2,34
1,85
2,83
3,29
3,35
2,07
3,38
3,80
3,57
2,90
4,35
5,04
5,20
96
85
82
86
100
90
85
86
= max.3
*3G 400 M3G 112-IA P. 92 / M3)
*3G 400 M3G 150-FF P. 93 / M5)
3~380-480 50/60 2450 2,50 3,80 -25..+40 14,6A
3~380-480 50/60 2750 3,35 5,20 -25..+40 20,3B
B
A
EC centrifugal fans RadiPacbackward curved, 400
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
nrpm
PedkW
IA
LWAdB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
37
I
nfor
mat
ion
25
0
280
63
0
710
80
0
900
2016
-02
Technical features: See connection diagram P. 92 f. Touch current:
38
2016
-02
R3G 400-PI92-01 (Centrifugal fan)
K3G 400-PI92-02 (Centrifugal module with support bracket)
6
252
3172
128.75
225.5 275
M10 (6x)
6x60
285
.2+
1.5
455
232
72
67.73
96
417
440
455
11
(4x)
37424463
15
450500
4x9
4x90
45
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 188)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 40078-2-4013Not included in scope of delivery (k-factor: 188)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 400
39
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 400-PA27-71 (Centrifugal fan)
K3G 400-PA27-71 (Centrifugal module with support bracket)
128.75225.5
285
.2+
1.5
5
252
3102275
M10 (6x)
6x60
455
232
70
67.7
396
450
4x9
440
455
4373682
15
4x90
35
492500
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 188)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 40078-2-4013Not included in scope of delivery (k-factor: 188)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 400
40
2016
-02
qv m/h
cfmP fs
Pa
in w
g
4000 8000 12000
0 2000 4000 6000 8000
400
800
1200
1600
24
6
111
3
4
2
3
4
23
42
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: Sheet aluminium Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 5 Direction of rotation: Clockwise viewed toward rotor Degree of protection: A IP 54; B C IP 55 Insulation class: A "B"; B C "F" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
1790
1790
1790
1790
2140
2140
2140
2140
2600
2600
2600
2600
1,00
1,53
1,74
1,66
1,71
2,66
2,90
2,76
3,07
4,64
5,25
5,14
1,61
2,38
2,70
2,57
2,69
4,09
4,50
4,25
4,78
7,13
8,00
7,89
91
82
77
82
96
85
81
86
102
92
87
91
= max.3
*3G 450 M3G 112-IA P. 92 / M3)
*3G 450 M3G 150-FF P. 93 / M5)
3~380-480 50/60 1730 1,74 2,70 -25..+50 17,0A
3~380-480 50/60 2140 2,90 4,50 -25..+40 23,5B
*3G 450 M3G 150-IF P. 92 / M3) 3~380-480 50/60 2600 5,25 8,00 -25..+40 31,0C
B
C
A
EC centrifugal fans RadiPacbackward curved, 450
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
nrpm
PedkW
IA
LWAdB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
41
I
nfor
mat
ion
25
0
280
31
0
710
80
0
900
2016
-02
Technical features: See connection diagram P. 92 f. EMC: C Interference emission according to EN 61000-6-3, except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW C Immunity to interference according to EN 61000-6-2 Touch current:
42
2016
-02
R3G 450-PI86-01 (Centrifugal fan)
K3G 450-PI86-02 (Centrifugal module with support bracket)
140
5
254
252275
3482
M10 (6x)
6x60
319
.7+
1.5
530
232
70
75.6
480
580
4x9
440
530
11
(4x)
412.52
4853
15
4x90
15
622630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 240)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 45075-2-4013Not included in scope of delivery (k-factor: 240)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 450
43
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 450-PA23-71 (Centrifugal fan)
K3G 450-PA23-71 (Centrifugal module with support bracket)
140.2
5
253.6
252
3412
275
M10 (6x)
6x60
319
.7+
1.5
530
232
70
75.6
480
580
4x9
440
530
11
(4x)
407.524773
15
4x9015
622630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 240)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 45075-2-4013Not included in scope of delivery (k-factor: 240)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 450
44
2016
-02
R3G 450-PB24-01 (Centrifugal fan)
K3G 450-PB24-01 (Centrifugal module with support bracket)
140
5
254 324
3762
304
M10 (6x)
6x60
319
,7+
1.5
530
280
113
75.64
80
580
4x9
440
530
11
(4x)
442.525563
15
9015
622630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 240)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 45075-2-4013Not included in scope of delivery (k-factor: 240)Dimensions: see Accessories chapter
Cable glandM25 x 1.5:Cable diametermin. 9 mm, max. 16 mmTightening torque 9 0.9 Nm
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 450
45
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0Co
mpa
ct d
esig
nTe
chno
logy
Agen
ts
46
2016
-02
qv m/h
cfmP fs
Pa
in w
g
4000 8000 12000 16000
0 2000 4000 6000 8000 10000
400
800
1200
1600
24
6
1 1
3
3
4
4
2
2
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: Sheet aluminium Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 5 Direction of rotation: Clockwise viewed toward rotor Degree of protection: IP 55 Insulation class: "F" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
= max.3A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
1910
1910
1910
1910
2250
2250
2250
2250
1,98
2,92
3,38
3,45
3,24
4,86
5,70
5,70
3,09
4,49
5,19
5,30
5,05
7,47
9,00
8,74
102
92
86
53
105
95
88
87
*3G 500 M3G 150-FF P. 93 / M5)
*3G 500 M3G 150-IF P. 92 / M3)
3~380-480 50/60 1910 3,45 5,30 -25..+40 24,3A
3~380-480 50/60 2250 5,70 9,00 -25..+40 32,0B
B
A
EC centrifugal fans RadiPacbackward curved, 500
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
nrpm
PedkW
IA
LWAdB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
47
I
nfor
mat
ion
25
0
710
80
0
900
2016
-02
Technical features: See connection diagram P. 92 f. EMC: A Interference emission according to EN 61000-6-4 B Interference emission according to EN 61000-6-3, except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW A B Immunity to interference according to EN 61000-6-2 Touch current:
48
2016
-02
R3G 500-PA23-71 (Centrifugal fan)
K3G 500-PA23-71 (Centrifugal module with support bracket)
156
5
2822753732
252
M10 (6x)
6x60
355
+2
5852
32
70
75
470
580
4x9
440
585
11
(4x)
438.525083
15
4x90
15
622630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 281)
Tightening torque 3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 64025-2-4013Not included in scope of delivery (k-factor: 281)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 500
49
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 500-PB33-01 (Centrifugal fan)
K3G 500-PB33-01 (Centrifugal module with support bracket)
156
5
2823244082
304
M10 (6x)
6x60
355
+2
585
280
113
75
470
580
4x9
440
585
11
(4x)
473.52
5873
15
4x9015
622630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 281)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 64025-2-4013Not included in scope of delivery (k-factor: 281)Dimensions: see Accessories chapter
Cable glandM25 x 1.5:Cable diametermin. 9 mm, max. 16 mmTightening torque 9 0.9 Nm
Note installedposition!Install supportstruts as illustrated!
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 500
50
2016
-02
qv m/h
cfmP fs
Pa in w
g
4000 8000 12000 16000 20000
0 2000 4000 6000 8000 10000 12000
400
800
1200
12
34
56
11
3
3
4
4
2
2
= max.3A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
1540
1540
1540
1540
1760
1760
1760
1760
1,83
2,81
3,30
3,23
2,79
4,25
5,00
4,79
2,88
4,32
5,10
4,95
4,36
6,52
7,70
7,32
97
88
82
82
101
92
84
87
*3G 560 M3G 150-IF P. 93 / M5)
*3G 560 M3G 150-NA P. 92 / M3)
3~380-480 50/60 1540 3,30 5,10 -25..+40 30,5A
3~380-480 50/60 1760 5,00 7,70 -25..+40 38,5B
B
A
EC centrifugal fans RadiPacbackward curved, 560
Material: Support bracket: Steel, painted black Support plate and inlet ring: Sheet steel, galvanized Impeller: Sheet aluminium Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 5 Direction of rotation: Clockwise viewed toward rotor Degree of protection: IP 55 Insulation class: "F" Installation position: Shaft horizontal or rotor on bottom, rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
nrpm
PedkW
IA
LWAdB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
51
I
nfor
mat
ion
25
0
710
80
0
900
2016
-02
Technical features: See connection diagram P. 92 f. EMC: Interference emission according to EN 61000-6-3, except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW Immunity to interference according to EN 61000-6-2 Touch current:
52
2016
-02
R3G 560-PB31-71 (Centrifugal fan)
K3G 560-PB31-71 (Centrifugal module with support bracket)
175
82
6
314 275432.52
252
M10 (6x)
6x60
398
.2+
2
655
515
232
70
750
4x9
545
655
11
(4x)
504.525743
15
4x90
15
792800
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 348)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 64030-2-4013Not included in scope of delivery (k-factor: 348)Dimensions: see Accessories chapter
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 560
53
I
nfor
mat
ion
25
0
280
31
0
630
71
0
800
90
0
2016
-02
35
5
400
45
0
500
56
0
R3G 560-PC04-01 (Centrifugal fan)
K3G 560-PC04-01 (Centrifugal module with support bracket)
175
82
6
314 3244722
304
M10 (6x)
6x60
398
.2 +
2
655
515
280
113
750
4x9
545
655
11
(4x)
544.526583
15
4x90
15
792800
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 348)
Tightening torque3.5 0.5 Nm
Cable glandM20 x 1.5: Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 64030-2-4013Not included in scope of delivery (k-factor: 348)Dimensions: see Accessories chapter
Cable glandM25 x 1.5:Cable diametermin. 9 mm, max. 16 mmTightening torque 9 0.9 Nm
Note installedposition!Install supportstruts as illustrated!
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 560
5000 10000 15000 20000 25000
0
400
800
1,6
200 0,8
600 2,4
1000 4,0
1800 7,23,
2
1200 4,8
1400 5,6
1600 6,4
10000 12000 140002000 4000 6000 8000 cfm
qV
P fs
Pa
m3/h
in w
g
4
3
2
111
2
3
4
43
2
Motor
*3G 630 M3G 150-NA P. 92 / M3)
*3G 630 M3G 200-HF P. 92 / M3)
3~380-480 50/60 1130 2,90 4,50 -25..+55 40A
3~380-480 50/60 1500 6,75 10,3 -25..+50 125B
Material: B C Cube design with inlet ring: Sheet steel, galvanized and coated with light gray plastic (RAL 7035) Impeller: Sheet aluminium; Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 7 Direction of rotation: Clockwise viewed toward rotor Degree of protection: A IP 55; B C IP 54 (according to EN 60529) Insulation class: "F" Installation position: Shaft horizontal ( B C base mounting only) or rotor on bottom; rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
*3G 630 M3G 200-QA 3~380-480 50/60 1850 11,0 17,0 -25..+40 160C
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
1130
1130
1130
1130
1500
1500
1500
1500
1850
1850
1850
1850
2,16
2,83
2,90
2,46
4,52
5,76
6,75
6,33
7,46
10,0
11,0
9,89
3,26
4,30
4,50
3,73
7,00
8,87
10,3
9,69
11,6
15,4
17,0
15,2
88
81
78
79
97
92
88
88
101
96
91
92
54
2016
-02
B
C
A
= max.3
EC centrifugal fans RadiPacbackward curved, 630
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: nrpm
PedkW
IA
LWAdB(A)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
R3G 630-AP01-01 (Centrifugal fan)
K3G 630-AP01-01 (Centrifugal module with support bracket)
6x60
6xM10
232
252275
2
+3.
6
318.3
224 6
444 7
16
634
98.535970
o652o800
o7501
11
(8x)
439 2.5 20508 3
Max. clearance for screw 25 mm
56
2016
-02
Tightening torque3.5 0.5 Nm
Cable gland M20 x 1.5 (3x)Accessory part: Inlet ring 64040-2-4013Not included in scope of delivery (k-factor: 438)Dimensions: see Accessories chapter
Cable glandM20 x 1.5 (3x): Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Pressure tap (k-factor: 438)
Note installedposition!Install supportstruts as illustrated!
EC centrifugal fans RadiPacbackward curved, 630
K3G 630-AR02-01 (Centrifugal module with cube design)
K3G 630-AS05-01 (Centrifugal module with cube design)
M20x1.5 (2x) M25x1.5
*6744x11
8x11
760660*159 *451
652.5511.5
20506
666
4x11
*169 *500*6744x11 660
760
8x11 20570
711
M20x1.5 (2x) M25x1.5
506
4x11
666
57
2016
-02
Inlet ring with pressure tap (k-factor: 438) Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Cable diametermin. 9 mm, max. 16 mmTightening torque 6 0.9 Nm
* Mounting position for vibration- absorbing and spring elements, only floor mounting allowed for horizontal shaft position.
Inlet ring with pressure tap (k-factor: 438)Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 6 0.6 Nm
Cable diametermin. 16 mm, max. 20.5 mmTightening torque 6 0.6 Nm
* Mounting position for vibration- absorbing and spring elements, only floor mounting allowed for horizontal shaft position.
I
nfor
mat
ion
25
0
710
80
0
900
28
0
310
63
0
355
40
0
450
50
0
560
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 630
58
2016
-02
5000 10000 15000 20000 25000 30000
0
400
800
1,6
200 0,8
600 2,4
1000 4,03,
2
1200 4,8
1400 5,6
1600 6,4
10000 150005000 cfm
qV
P fs
Pa
m3/h
in w
g
1 1 1
4
3
2
4
3
4
3
2
2
Motor
*3G 710 M3G 150-NA
*3G 710 M3G 200-LA
3~380-480 50/60 920 2,80 4,30 -25..+40 44A
3~380-480 50/60 1300 7,86 12,0 -25..+40 163B
*3G 710 M3G 200-QA 3~380-480 50/60 1550 11,8 18,0 -25..+40 194C
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
920
920
920
920
1300
1300
1300
1300
1550
1550
1550
1550
1,82
2,52
2,80
2,57
5,12
6,91
7,86
7,37
7,63
10,4
11,8
11,1
2,72
3,77
4,30
3,82
7,87
10,6
12,0
11,2
11,9
16,0
18,0
17,1
84
80
78
78
96
91
86
87
101
94
88
91
B
C
A
= max.3
EC centrifugal fans RadiPacbackward curved, 710
Material: B C Cube design with inlet ring: Sheet steel, galvanized and coated with light gray plastic (RAL 7035) Impeller: Sheet aluminium; Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 7 Direction of rotation: Clockwise viewed toward rotor Degree of protection: A IP 55; B C IP 54 (according to EN 60529) Insulation class: "F" Installation position: Shaft horizontal ( B C base mounting only) or rotor on bottom; rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
P. 92 / M3)
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: nrpm
PedkW
IA
LWAdB(A)
59
2016
-02
Technical features: See connection diagram P. 92 EMC: A Interference emission according to EN 61000-6-3, except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW B C Interference emission according to EN 61000-6-4 Immunity to interference according to EN 61000-6-2 Touch current:
60
2016
-02
R3G 710-AP02-01 (Centrifugal fan)
K3G 710-AP02-01 (Centrifugal module with support bracket)
6001o8801
11 (
12x)
o783o960
4902.55593
25
Pressure tap (k-factor: 545)
Note installedposition!Install supportstruts as illustrated!
232
252275
2
+4.
6
354
250 15
501
806
720
11739470
6x60
6xM10
Max. clearance for screw 25 mm
Tightening torque3.5 0.5 Nm
Cable gland M20 x 1.5 (3x)Accessory part: Inlet ring 71075-2-4013Not included in scope of delivery (k-factor: 545)Dimensions: see Accessories chapter
Cable glandM20 x 1.5 (3x): Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
EC centrifugal fans RadiPacbackward curved, 710
61
2016
-02
K3G 710-AR03-01 (Centrifugal module with cube design)
K3G 710-AS06-01 (Centrifugal module with cube design)
4x11*234 *337*884
20x11
600750880960
25579.5
712.5
M20x1.5 (2x)M25x1.5
700
864
4x11
600750880960
20x1125621
759
*884 *252.5 *4054x11
M20x1.5 (2x)M25x1.5
700
4x11
864
Inlet ring with pressure tap (k-factor: 545) Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Cable diametermin. 9 mm, max. 16 mmTightening torque 6 0.9 Nm
* Mounting position for vibration- absorbing and spring elements, only floor mounting allowed for horizontal shaft position.
Inlet ring with pressure tap (k-factor: 545)
Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 6 0.6 Nm
Cable diametermin. 16 mm, max. 20.5 mmTightening torque 6 0.6 Nm
* Mounting position for vibration- absorbing and spring elements, only floor mounting allowed for horizontal shaft position.
I
nfor
mat
ion
25
0
710
80
0
900
28
0
310
63
0
355
40
0
450
50
0
560
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 710
62
2016
-02
5000 10000 15000 20000 25000 30000 35000
0
400
800
1,6
200 0,8
600 2,4
1000 4,03,
2
1200 4,8
1400 5,6
1600 6,4
10000 15000 200005000 cfm
qV
P fs
Pa
m3/h
in w
g
4
1 1
2
3
4
3
2
Motor
K3G 800-AR08 -01 M3G 200-QA
K3G 800-AS07 -01 M3G 200-QA
3~380-480 50/60 1050 7,53 11,6 -25..+40 189A
3~380-480 50/60 1370 11,6 17,8 -25..+40 196B
Material: Cube design with inlet ring: Sheet steel, galvanized and coated with light gray plastic (RAL 7035) Impeller: Sheet aluminium; Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 7 Direction of rotation: Clockwise viewed toward rotor Degree of protection: IP 54 (according to EN 60529) Insulation class: "F" Installation position: Shaft horizontal (base mounting only) or rotor on bottom; rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
1050
1050
1050
1050
1370
1370
1370
1370
4,91
6,56
7,53
7,18
6,76
9,62
11,6
10,7
7,58
10,1
11,6
11,0
10,5
14,8
17,8
16,4
94
88
85
85
106
98
90
93
A
B = max.3
EC centrifugal fans RadiPacbackward curved, 800
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: nrpm
PedkW
IA
LWAdB(A)
63
2016
-02
Technical features: See connection diagram P. 92 EMC: Interference emission according to EN 61000-6-4 Immunity to interference according to EN 61000-6-2 Touch current:
64
2016
-02
K3G 800-AR08-01 (Centrifugal module with cube design)
4x11*251.5 *430*884
20x11
600750880960
25650
783
M20x1.5 (2x)M25x1.5
4x11
700
864
Inlet ring with pressure tap (k-factor: 695) Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Cable diametermin. 9 mm, max. 16 mmTightening torque 6 0.9 Nm
* Mounting position for vibration- absorbing and spring elements, only floor mounting allowed for horizontal shaft position.
EC centrifugal fans RadiPacbackward curved, 800
65
2016
-02
K3G 800-AS07-01 (Centrifugal module with cube design)
600750880960
20x1125621
759
*884 *252.5 *4054x11
M20x1.5 (2x) M25x1.5
700
864
4x11
Inlet ring with pressure tap (k-factor: 695)Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 6 0.6 Nm
Cable diametermin. 16 mm, max. 20.5 mmTightening torque 6 0.6 Nm
* Anschraubposition fr Schwing- bzw. Federelemente, bei horizontaler Wellenlage nur Bodenmontage erlaubt.
I
nfor
mat
ion
25
0
710
80
0
900
28
0
310
63
0
355
40
0
450
50
0
560
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 800
66
2016
-02
5000 10000 15000 20000 25000 30000 35000
0
400
800
1,6
200 0,8
600 2,4
1000 4,03,
2
1200 4,8
10000 15000 200005000 cfm
qV
P fs
Pa
m3/h
in w
g
1 1
2
3
4
4
3
2
Motor
K3G 900-AR10 -01 M3G 200-QA
K3G 900-AS08 -01 M3G 200-QA
3~380-480 50/60 860 7,52 11,5 -25..+40 222A
3~380-480 50/60 1050 8,70 13,5 -25..+40 232B
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
860
860
860
860
1050
1050
1050
1050
5,03
6,75
7,52
7,02
5,04
7,33
8,70
7,74
7,72
10,3
11,5
10,7
8,03
11,4
13,5
12,0
92
87
82
81
99
91
86
87
A
B= max.3
EC centrifugal fans RadiPacbackward curved, 900
Material: Cube design with inlet ring: Sheet steel, galvanized and coated with light gray plastic (RAL 7035) Impeller: Sheet aluminium; Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 7 Direction of rotation: Clockwise viewed toward rotor Degree of protection: IP 54 (according to EN 60529) Insulation class: "F" Installation position: Shaft horizontal (base mounting only) or rotor on bottom; rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Spee
d(1)
Max
.In
put p
ower
(1)
Max
.In
put c
urre
nt(1
)
Wei
ght
Perm
. am
bien
t tem
p.
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection. Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: nrpm
PedkW
IA
LWAdB(A)
67
2016
-02
Technical features: See connection diagram P. 92 EMC: A Interference emission according to EN 61000-6-4 A Immunity to interference according to EN 61000-6-2 Touch current:
68
2016
-02
K3G 900-AR10-01 (Centrifugal module with cube design)
4x11*1104 *440*203.5
24x11
40080095011001180
30612
745
M20x1.5 (2x) M25x1.5
4x11
930
1084
Inlet ring with pressure tap (k-factor: 900)
Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 4 0.6 Nm
Cable diametermin. 9 mm, max. 16 mmTightening torque 6 0.9 Nm
* Mounting position for vibration- absorbing and spring elements, only floor mounting allowed for horizontal shaft position.
EC centrifugal fans RadiPacbackward curved, 900
69
2016
-02
K3G 900-AS08-01 (Centrifugal module with cube design)
4x11*181 *375*1104 400
80095011001180
24x11 30
519657
M25x1.5M20x1.5 (2x)
4x11
930
1084
Inlet ring with pressure tap (k-factor: 900)
Tightening torque3.5 0.5 Nm
Cable diametermin. 4 mm, max. 10 mmTightening torque 6 0.6 Nm
Cable diametermin. 16 mm, max. 20.5 mmTightening torque 6 0.6 Nm
* Mounting position for vibration- absorbing and spring elements, only floor mounting allowed for horizontal shaft position.
I
nfor
mat
ion
25
0
710
80
0
900
28
0
310
63
0
355
40
0
450
50
0
560
Com
pact
des
ign
Tech
nolo
gyAg
ents
EC centrifugal fans RadiPacbackward curved, 900
1000 2000 3000 4000 5000 6000 7000 8000 9000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
1200 4,8
1400 5,6
500 1000 1500 2000 3000 3500 4000 4500 5000 55002500 cfm
qV
P fs
Pa
m3/h
in w
g
4
3
3
2
2
1 1 1 1 1
22
33
44
4
4
3
2
Motor
R3G 280-AJ14 -C1 M3G 084-GF
R3G 310-BC38 -01 M3G 112-GA
3~380-480 50/60 3260 0,99 1,60 -25..+60 6,8A
3~380-480 50/60 3170 1,65 2,50 -25..+50 12,1B
Material: Impeller: Sheet aluminium Rotor: Painted black Electronics housing: Die-cast aluminium Number of blades: 7 Direction of rotation: Clockwise viewed toward rotor Degree of protection: IP 54 Insulation class: "B" Installation position: Shaft horizontal or rotor on bottom; rotor on top on request Condensation drainage holes: Rotor side Mode: Continuous operation (S1) Mounting: Maintenance-free ball bearings
R3G 355-BD43 -01 M3G 112-GA 3~380-480 50/60 2650 1,73 2,60 -25..+60 12,6C
A 1
A 2
A 3
A 4
B 1
B 2
B 3
B 4
C 1
C 2
C 3
C 4
3260
3260
3260
3260
3170
3170
3170
3170
2650
2650
2650
2650
0,70
0,88
0,99
0,87
1,23
1,52
1,65
1,54
1,25
1,56
1,73
1,63
1,31
1,57
1,60
1,57
1,83
2,27
2,50
2,30
1,86
2,33
2,60
2,42
89
86
84
85
90
88
85
88
90
86
84
86
70
2016
-02
= max.3
R3G 400-AS23 -01 M3G 150-FF P. 92 / M3) 3~380-480 50/60 2550 2,84 4,20 -25..+60 21,3D
R3G 450-AS24 -01 M3G 150-FF P. 92 / M3) 3~380-480 50/60 2040 2,38 3,60 -25..+60 22,0E
D 1
D 2
D 3
D 4
E 1
E 2
E 3
E 4
2550
2550
2550
2550
2040
2040
2040
2040
2,10
2,59
2,84
2,68
1,64
2,16
2,38
2,17
3,13
3,84
4,20
3,95
2,48
3,23
3,60
3,24
92
89
86
89
90
85
82
86
B C
A D
E
EC centrifugal fans RadiPacbackward curved, 280 - 450 (compact design)
P. 97 / L6)
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data Tech
n. fe
atur
esan
d co
nnec
tion
diag
ram
VAC Hz rpm kW A C kg
Curv
e
Nom
inal
vol
tage
rang
e
Freq
uenc