Post on 05-Nov-2020
Detection Analysis Location
Radio Frequency (RF) Detectors
Multi Functional Counter Surveillance Equipment
Radio Monitoring and Signal Analysis
Non-linear Junction Detectors (NLJD)
Explosives Detectors
WWW.SEKOTECH.COM
SEKOTECHTechnicalSurveillanceCounterMeasures
Dimensions (transportation):
Height 57 cm
Width 22 cm
Thickness 12 cm
Weight 1.5 Kg
LornetNON LINEAR JUNCTION DETECTOR
Main features:
• Small dimensions and weight of the device
• Easy-to-use
• Automatic and manual modes of power change of the probing signal
• Use of the latest technologies and materials, ergonomic
• High detection potential
• Use of wireless earphones
A non-linear junction detector Lornet is designed to detect various kinds of electronic devices containing semiconductor elements, such as microphone amplifiers, audio-recorders, eavesdropping and other remotely controlled devices; both in switched-on and switched-off modes.
Delivery set:1. Lornet device with Li-Ion battery2. Wireless accessories (a receiver with earphones)3. Power adapter-charger (110-240V)4. Transportation bag
Technical specifications:
Type of a probing signal pulse CW
Probing signal frequency 890 - 891 MHz
Probing signal power pulse - 15 W CW - 1 W
Sensitivity not worse -120 dBm
Dynamic range more than 80 dB
Power supply Rechargeable battery
Operation time over 3,5 h (at pulse probing signal) over 1,5 h (at CW probing signal)
Dimensions (in operation):
Height 100 cm
Width 15 cm
Thickness 4 cm
Weight 1 Kg
Technical specifications:
Type of a probing signal pulse CW
Probing signal frequency 2.4 - 2.483 GHz
Probing signal power pulse - 10 W CW - 1 W
Sensitivity not worse -108 dBm
Dynamic range more than 80 dB
Power supply Rechargeable battery
Operation time over 3h (at pulse probing signal) over 1,5h (at CW probing signal)
Dimensions (in operation):
Height 39 cm
Width 10 cm
Thickness 4 cm
Weight 700 g
Dimensions (transportation):
Height 23 cm
Width 10 cm
Thickness 5.5 cm
Weight 1500 g
Lornet-24NON LINEAR JUNCTION DETECTOR
Main features:
• New! Lornet-24 delivery set now includes 2 pcs. replaceable batteries. Operator can work on one battery while another is on charge.
• It is a unique device worldwide by its frequency, weight and dimension characteristics.
• All operation modes of Lornet device are available (automatic and manual modes of power change of the probing signal in a pulse mode, manual power change in CW mode).
• Use of the latest technologies and materials, ergonomic.
• High detection potential (in some cases due to a higher frequency of probing signal it is more efficient than detectors using more power, but operating in a standard range).
• Wireless earphones.
• It is possible to operate in hard-to-reach places and under conditions of limited space (antenna thickness does not exceed 18 mm).
A non-linear junction detector Lornet-24 is used for conducting a strategic and search work afield, in premises, transport, and is designed to find specific equipment containing semiconductor components.
An automatic system of frequency selection is integrated into the device, and it can tune away from a narrowband interference automatically (by a criterion of minimum noise of the receiving channel of the 2nd harmonic).
Delivery set:1. Lornet-24 device with 2 pcs Li-Ion batteries2. Wireless accessories (a receiver with earphones)3. Power adapter-charger (110-240V)4. Transportation bag
Technical specifications:
Type of a probing signal pulse
Probing signal frequency 3.5 - 3.620 GHz
Probing signal power pulse - 20 W
Detection ranger 1-10 m or more
Sensitivity not worse -110 dBm
Dynamic range not lesss than 40 dB
Power supply Rechargeable battery
Operation time up to 3h (at pulse probing signal) Dimensions:
Height 47,7 cm
Width 30,3 cm
Thickness 22,7 cm
Weight 1.2 Kg
Main features:
• 3.6 GHz high frequency of probing signal outside of GSM band.
• Long detection range 1-10 m or more.
• Narrow diagram of antenna directivity.
• Laser pointer to pinpoint inspected area.
• Easy-to-use, ergonomic.
• Automatic and manual adjustment of probing signal power.
• Electromagnetic effect on operator (during operation) is very low.
• Wireless earphones.
It is very efficient when it comes to identifying of
miniaturized electronic devices (10x20mm) at a
considerable distance, which is sometimes crucial.
For instance, a suspicious object has to be analyzed within
a safe distance.
Moreover, the use of a super high signal frequency range
gives Lornet-36 some unique capabilities to detect
semiconductors covered by various materials.
It can also detect devices through slits and holes,
ungrounded shielding, etc.
Delivery set:1. Lornet-36 device with Li-Ion battery2. Wireless accessories (a receiver with earphones)3. Power adapter-charger (110-240V)4. Transportation bag
A non-linear junction detector Lornet-36 is an
indispensable tool for a quick and reliable location of
unauthorized electronic devices during investigation
operations in premises with a high density of electronic
equipment.
NON LINEAR JUNCTION DETECTOR
Lornet-36
Technical specifications:
Type of a probing signal pulse
Probing signal frequency1st probing signal 2nd probing signal
789,5-791,5 MHz;3581,5-3607,5 MHz
Transmitter peak power in each frequency range 40W / 20W
Duty cycle 0,3% and 5%
Detection ranger 1-10 m or more
Sensitivity -110 dBm
Power supply Rechargeable battery
Operation time 0.3% duty cycle 0.5% duty cycle
not less than 3 h 1.5 h
Dimensions:
Height 30,5 cm
Width 30,5 cm
Thickness 22,7 cm
Weight 1.6 Kg
Main features:
• The first non-linear detector which combines the advantages of a microwave detector and the detector of traditional range with the weight less than 1 kg and possibility to indicate the results in both ranges simultaneously.
• Long detection range 1-10 m or more.
• Laser pinpointing for a space selective object localization.
• Easy-to-use, ergonomic.
• Automatic and manual adjustment of probing signal power.
• Electromagnetic effect on operator (during operation) is very low.
• Wireless earphones.
Lornet-0836 is an indispensable tool for a quick and
reliable detection of devices containing semiconductor
components. It can be used for counter-surveillance
investigation works in premises (covert transmitters
identification), as well as for location of explosive devices
outdoor. The DPF (double probing frequency) technology
with a patent pending antenna system places it beyond
comparison to other rivals.
Unique opportunity to detect semiconductor
elements hidden by different materials (detection
through cracks, unearthed shielding, reflections from
smooth surfaces, SIM card is detected at the distance
of 80 cm, etc.)
Delivery set:1. Lornet-0836 device with Li-Ion battery2. Wireless accessories (a receiver with earphones)3. Power adapter-charger (110-240V)4. Transportation bag
Lornet-0836NON LINEAR JUNCTION DETECTOR
NR-μNON LINEAR JUNCTION DETECTOR
Main features:
• various electronic units detection in any operational mode: active, switched off and stand-by
• light portable design with built-in connecting cables (from antenna to the main unit), optional display on the back of antenna unit cover
• original circuit design for optimum combination of pulse & CW NLJD merits
• extended continuous operational time (without battery replacement)
• spare, replaceable battery
Detection of covert eavesdropping
electronics (radio microphones, microphone
amplifiers, dictaphones and etc.) in premises.
Examination of office and living premises
structures as well as furniture and domestic
articles for concealed bugging facilities.
Delivery set:1. NR-μ device with Li-Ion battery2. Power adapter-charger (110-240V)3. Spare battery4. Transportation bag
Technical specifications:
Antenna, polarization directional, circular
Probing signal frequency 890 - 891 MHz
Probing signal power searching envelope separation (20K)
0.4 W 2 W
Receiver sensitivity (under 10dB signal/noise ratio)
not worse than -150 dBW (-120dBm)
Dynamic range more than 80 dB
Power supply Rechargeable battery
Operation time not less than 4 h
Dimensions:
Height 100 cm
Width 15 cm
Thickness 4 cm
Weight 2.9 Kg
NR-900 EK EagleNON LINEAR JUNCTION DETECTOR
NR-900 EK application possibilities:
• roads, terrain and objects inspection for mines,
improvised explosive devices (IED) and other
explosive appliances with electronic components;
• searching for weapons caches, ammunition,
explosive devices and communication facilities;
• investigation of suspicious items, searching of
destructive and terrorist devices.
Main features:
• extended detection range;
• equipment design allows its usage in tactical airborne missions;
• efficient use in search/reconnaissance missions;
• high searching speed;
• safe to handle, user-friendly design;
• extended continuous operational time without battery replacement;
• long-term operation in field conditions.
NR-900 EK is designed for detection of mines and explosive devices with
electronic fuses (activation system) concealed on the ground surface,
beneath the surface (snow), under the road pavement and in various
facilities.
NR-900 EK Detects:• communicational transmitters & receivers as well as alarm and
remote control system facilities;• electronic and electromechanical timers;• acoustic, magnetic, optoelectronic sensors and midget TV cameras;• built-in metal-ware as well as hidden machinery and appliances;• domestic electronic units and alpine skiing equipment in snow traps
during rescue operations.
Delivery set:1. NR-900EK device with battery2. Power adapter-charger (110-240V)3. Spare battery4. Transportation bag
Technical specifications:
Probing signal type pulse
Probing signal frequency 890 - 891 MHz
Receiver 2-channel (2nd and 3rd harmonics)
Probing signal power average peak
0,15 W 200 W
Dynamic range more than 80 dB
Power supply Ni-Cad battery, 6V/7Ah
Audio output headphones
User interface LED display
Start-up time less than 5 min
Operation time not less than 8 h
Operating temperature -30º C…+50º C
Weight (ready for operation /transportation package) 5.1 Kg / 12.0 Kg
Technical specifications:
Type of a probing signal pulse and continuous
Probing signal frequency 2.4 GHz
Probing signal power 0.5 W
Antennas polarization circular polarization
Free channel selection automatic
Indication LED diodes
Receiver sensitivity -150 dB/W
Detection ranger 10 cm - 1 m
Dynamic Range 80 dB
Power supply Internal Li-Ion rechargeable battery
Operation time pulse modecontinuous
not less than 2.5 h 2 h
Charging time 2 hours
Working temperature from -100 C to + 400 C
Buclet-2NON LINEAR JUNCTION DETECTOR
Main features:
• Compact and easy to use.
• 2.4 GHz probing signal.
• Automatic selection of operating
channel having minimum noise level.
Buclet-2 is ideal for use in correctional
facilities to inspect packages or inmate cells
for presence of forbidden objects.
As other non-linear junction detectors Buclet-2 detects all
electronic equipment having semiconductor elements in
active and passive (switched-off) modes.
Buclet-2 is designed to perform inspection of packages,
difficult to access places. It is also compact and easy to
operate for inexperienced user as it has minimum set of
functions and indication of only 2nd harmonics.
Delivery set:1. Buclet-2 non-linear junction detector2. Headphones3. Power adapter-charger (220V)4. Packing box
Dimensions:
Dimmensions in pack 28 cm x 14 cm x 10 cm
Dimmensions unpacked 25 cm x 10 cm x 6 cm
Weight 360 g
Raksa iDetRF Detector
RAKSA iDet detects:
• Cellular phones of GSM900/1800,
UMTS(3G), CDMA 450 (453-458 MHz)
• Cordless DECT phones
• Bluetooth and Wi-Fi devices
• Wireless video cameras
• Radio transmitters with analog
modulation (AM, FM, PM)
• Radio transmitters with digital
modulation and continuous carrier (FSK,
PSK, etc.)
• Radio transmitters with wideband
modulation up to 10 MHz bandwidth
Main features:
• Selective reception of radio signals
• High speed of scanning and analyzing
• Detection of wideband and digital
signals
• Adaptation to the background noise in
Guard Mode
• Difference search mode
• Audio monitoring
• Signal frequency and level measurement
• Alarm events log
• Discrete alarm (vibration mode)
• No need of external antenna
RAKSA iDet – a selective RF Detector which can be used
to detect and locate in a near field a wide variety of radio
transmitters used for a secret access to information or its
leakage.
RAKSA iDet is a super heterodyne receiver with a low
IF and frequency synthesizer. Scanning and analyzing
cycle period is 1.0-1.5 sec. The device can operate within
guard, sweep, search, deviation measure modes and
monitoring of digital signals.
Delivery set:1. Raksa Idet2. Power adapter-charger (110-240V)3. Packing box
Technical specifications:
Frequency band 50 - 3300 МHz
Typical sensitivity 70 mV/m
Dynamic range 50 dB
Period of full scanning cycle ≤ 1.5 s
Power supply Ni-Cad battery, 6V/7Ah
Running time in guard mode 4 - 12 h
Running time in other modes 3 hours
OLED display 128 x 64
Dimensions 77 х 43 х 18 mm
Weight 35 g
ST-110RF Detector
ST 110 Detects:
• Radio-microphones (BUGs) ;
• telephone radio retransmitter (TAP);
• wireless stethoscope;
• Video-cameras with radio channel for data transfer;
• Radio beacons for people, vehicles or cargos tracking systems;
• Mobile phones and radio modems of GSM, DECT standards;
• Data transmission devices of BLUETOOTH and WLAN standards.
• Principle of operation of ST 110 is based on broadband detection of
electrical field
Search mode:This mode is intended to search and detect RD location. Visual indication of signal level on 32-seg. scale.GSM, DECT, BLUETOOTH, WLAN detection
Oscilloscope mode:Oscilloscope mode allows operator to view oscillogram of selected signal
Log view mode:This mode is intended to view the log of events resulting from the unit running in MONITORING mode. The classification of the events by time, duration or signal level is provided.
PC Software allows: time graphic display of data and the results of operation of the ST 110 ;ST 110 remote full control using PC;extended settings assignment for MONITORING mode; load and display textual and graphical information of the operation of the ST 110 in MONITORING mode (Event Log); Firmware updating
Monitoring mode:This mode is designed for independent operation of ST110 on preset conditions. The information about detected signals is saved by means of non-volatile memory of the device (9 banks, each for 999 events). Scheduled work operation is also provided.
ST 110 is designed for detection and localization of radio-wave radiation devices
(RD) that are designed or used for unauthorized data transfer via radio channel.
Technical specifications:
Frequency band 50-2500 МHz
Threshold sensitivity, dBm-75 (50 MHz)-70 (1500 MHz)-50 (2500 MHz)
Dynamic Range of indication, dB 55 (50-2000 MHz)40 (2000-2500 MHz)
Sensitivity of frequency meter , dBm-35 (50 МHz)-50 (500 МHz)-20 (2500 МHz)
Frequency measurements accuracy, % 0.005
Cut-off frequency of LPF, MHz 750
SHF antenna-detector ST110.SHF
Frequency range , MHz 2000-7000
Threshold sensitivity, W/cm2 2x10-10
Dynamic Range , dB 45
Power supply Li Pol 3.6V
Consumption current, mА 65
Indication Color OLED Display 160X128
Dimension main block (with-out antenna), mm 90x54x21
ST-165CELLULAR COMMUNICATIONS SIGNAL DETECTOR
Automatic mode:This mode is intended for DRTD automatic detection when it exceeds the operation threshold set by user. Signal data are logged. Scheduled work is provided.
Manual mode:This mode is intended to detect:• location of signal source;• threshold levels value for later use in AUTOMATIC MODE.
Indication of BASE STATION signals level is provided in this mode
Additional possibilities:• Adjustment on “local” country frequencies of standard UMTC• Built-in Relay (terminals on the external port) extends the
functionality of the ST 165 to remotely control jammers and additional indicators.
PC Software allows: • time graphic display of data and the results of operation of the ST 165 ;• ST 165 remote full control using PC;• Firmware update.
Log view mode:This MODE is designed for viewing the log of events. Time of event, its duration, type of event, signal strength are displayed.
ST 165 is designed for detection and identification of mobile radio
transmitters of cellular communications standards (mobile phones
and modems of GSM 900, 1800, UMTS), wireless data transmission
(WI FI and BLUETOOTH) and cordless phones (DECT). Additionally
indication of base stations power signal strength and data exchange
intensity is provided. All mentioned above will be referred to as Digital
Radio Transmitting Devices (DRTD)
ST 165 operates on the basis of direct-conversion receiver. To detect signals,
the ST 165 scans a series of frequency ranges of the known transmission
standards. The user can set up the detection threshold and the number of
desired frequency bands. Signals identification is performed on basis of
analysis of detected signals time parameters.
Delivery set:1. ST-165 device2. Power adapter-charger (110-240V)3. PC Software4. Packing box
Technical specifications:
Frequency ranges, MHz
890-9601710-19001940-21442400-2600430-465 (with ST165.CDMA version)
Level ranges of displayed signal, dB
890-960 MHz2400-2600MHz1940-2144MHz1710-1900MHz
-75 – +10-70 – +10-80 – +10-70 – +10
Alarm level setting range, dB 60
The weakening out of band signals, not worse, dB 50
Power supply Li Pol 3.6V
Consumption current, mА 300
Indication Color OLED Display 160X128
Dimension main block (with-out antenna), mm 90x54x21
ST-131 Piranha II (page 1 of 3)
MULTIFUNCTION TSCM DEVICE
Operating modes:
• RF detector frequency meter
30 – 4400 MHz
• Digital signal level indication mode:
CDMA, GSM900, GSM1800, DECT,
3G, 2.4 GHz, 4G LTE
• Differential spectrum mode
• Oscilloscope
• Signal demodulation
• UHF detector 4000-18000 MHz
• Wire line scanner
• Wire line non-linear junction
detector
(only in ST-131N Piranha II)
• Optical IR channel
• Acoustoelectric channel
• Magnetic channel
The main types of the STM, for detection of which
ST131 is intended, include the following:
• The STM with transfer of information by radio channel.
Such devices include first of all:
• Radio microphones including devices with storage and
subsequent transfer of information (burst transmitter) and
Frequency Hopping Spread Spectrum (FHSS);
• Telephone radio broadcasting devices.
• Radio stethoscopes.
• Wireless video cameras.
• Mobile telephones and modems of CDMA, GSM, UMTS,
DECT standards used without authorization.
• Devices using digital channels of data transmission of
WLAN and BLUETOOTH standards.
• Radio beacons for object movement tracking.
• The STM that use AC power, telephone, security and fire
alarm lines for information transfer.
• The STM characterized by information transmission in
infra-red range.
• The STM characterized by transmission of information in
ultrasonic frequency range.
Multifunction detection device ST131 PIRANHA-II is designed for detection and localization of special technical means (STM) used for surreptitious obtaining of information, as well as identification of natural and artificial sources of information leakage.
ST-131 Piranha II (page 2 of 3)
MULTIFUNCTION TSCM DEVICE
Basic set:1. Main unit 2. UHF converter (ST131.UHF) 3. Broadband UHF antenna (ST131.UHF.A) 4. Wire line adapter (ST131.AWL) 5. Leads 6. Main unit supporting block 7. Main unit shoulder holder 8. Headphones 9. Tripod 10. Power supply unit - 2 pcs 11. AA batteries - 8 pcs12. Mini-disc with software 13. User manual
Supplementary set1. SHF DETECTOR ST131.SHF2. IR probe ST131.IR3. Magnetic field probe ST131.MF4. Control unit ST131.TEST
ST-131 Piranha ii - technical specifications:
Digital signal processing module
Simultaneous processing frequency range, MHz 0.01-30
Resolution ADC, bit 10, 14 and 16
Number of FFT points 32768 (PC mode) 512 (main unit)
Filters sizes, MHz 0.01-6.8 МHz
Demodulation types АМ, FM, SSB, TV (АМ)
Radio channel - UHF converter
Frequency range, MHz 30-4100
Displayed noise level Within the whole bandwidth, dBm Within DDC bandwidth 1 kHz, dBm
-90 main unit (-110 PC mode)- 110
Input signal maximal level, dBm 5
Sweep speed, GHz/sec, at least 10
Value of DDC bandwidth, MHz1024, 512, 224, 112, 54, 28, 6.8, 2.5, 0.63, 0.15, 0.075, 0.04, 0.001 и 0.0005
Identified data transfer standards CDMA, GSM, 3G,4G, WLAN, BLUETOOTH, DECT
Radio channel - SHF Detector ST131.SHF
Frequency range, MHz 4000-18000
Threshold sensitivity, W/cm2 -65
Antenna beamwidth, degrees 60-90
“WIRE LINE” Channel
Frequency range 1, MHz 0.01-30
Frequency range, 2, KHz 0.3 - 15
OPTICAL Channel
Dynamic range, dB 60
Frequency range, MHz 0.01-30
“ACOUSTOELECTRIC” Channel
Frequency range, KHz 0.01-125
input signal maximal level, dBm -5
Gain input amplifier 6, 14,20, 26, 34 40
Non-linear junction detector
Frequency of test signal, kHz 150-220
Main unit
Dimensions, mm 190x97x50
Indication 3.5” 240x320, TFT 262144 colors
Interface USB 2.0, 200 Mbit/s
Power supply 6 AA batteries (rechargeable batteries)
Only for ST-131N Piranha II:
ST-131 Piranha II (page 3 of 3)
MULTIFUNCTION TSCM DEVICE
Special software “ST131 ANALYZER-PRO” highly extends capacities of ST131 for analysis and processing of signals.
This software implemented the following functions:
• Spectral OSCILLOGRAPH and vector analysis
• “waterfall”
• Creation of signals data base
• MONITORING with expanded presets
• Streaming recording of signals to HDD of PC
Sirius (page 1 of 3)
WIRE LINES ANALYSER
The SIRIUS (4rd generation) is designed for detection of unauthorized galvanic connections, detection and analysis of signals in wire circuits and connected electronic devices, which appear as a result of acoustoelectric conversion or forming of modulation in return high frequency signal.
The SIRIUS provides the following possibilities to an operator:• Analysis of HF signals spectra.• Analysis of audio frequencies.• Injection of HF signals to wire circuits and data
processing equipment and analysis of converted signals.
• Impulse reflectometry.• Complex electrical measurements (mode of
digital multimeter, transient curve, volt-ampere curve, frequency-response characteristic, gain-phase characteristic, load-voltage characteristic).
• Extended possibilities for examination of wire
circuits.
• Wide frequency range of examined signals.
• Vector spectral analysis of signals using
different intermediate pass bands.
• High dynamic range of processed signals
amplitudes.
• High processing speed of input signals
resultant spectra.• Measurement of AC and DC voltage,
impedance, capacitance and inductance.• Demodulation of AM and FM signals in real
time.• Automatic compensation of injected signal
phase shifts in the mode of acoustically induced modulation in high frequency signal.
• Several automatic analysis modes.• Splashproof and shockproof case.
Distinctive features:
Signal Lines Commutator: 220 V, Telphone, LAN
Priboi (optional): Active acoustic system for generation of various tonal and noise signals
Parametric Microphone Imitator
Delivery set:1. Main unit2. Set of connection cables and adapters3. PRIBOI active acoustic system (optional)4. Simulator of parametric microphone5. Signal switcher6. Headphones7. UP-8 wire tracer
Sirius (page 2 of 3)
WIRE LINES ANALYSER
DETECTION OF EFFECT OF ACOUSTICALLY INDUCED MODULATION IN HF SIGNAL
Frequency range of excitation signal, kHz 10~400000
Root-mean-square voltage of excitation signal at LINE jack, V 1
Attenuation range of excitation signal level, not less than, dB 40
Detection of modulating signals with modulation factor (at SNR 10 dB), not more than 10-4
Pass bands for modulating signal, kHz 5; 25
Minimal step of excitation signal frequency tuning (for pass band of 5 kHz), Hz 100
Frequency resolution (for pass band of 5 kHz), Hz 10
Phase shift compensation between excitation signal and response signal, grad 0 ~180, with step of 1
Setting range of bias voltage, V ±15, with step of 1
Detected modulation formats AM, FM, PM
Frequency setting of test acoustic signal, Hz 63~11300, with step of 1
Acoustic signal amplitude at TONE jack output, mV 5, 100, 250, 500, 1000
Output impedance at TONE jack, Ω 620
...continued
ANALYSIS OF INPUT SIGNAL SPECTRUM
Input signal frequency range, kHz 10 ~ 400000
Dynamic range of input signal processing, not less than, dB 140
Sensitivity at input (SNR 10 dB) no more than, dBW/Hz -170
Maximum amplitude of input signal, V 10
Electronic attenuator of input signal, dB 20
Input impedance at LINE jack output, Ω 50
Setting range of bias voltage, V ±15, with step of 1
Number of processed dots in single capture 1024
Pass bands for converted signal (at -3dB level), kHz 5; 25; 250; 2500; 25000
Frequency resolution (for different pass bands, 5 kHz~25 MHz), kHz 0.01; 0.06; 0.6; 6; 60
Time of forming of single spectrum capture, no more than, s 0.05
Scanning time of 10~400000 kHz frequency range (at 25 MHz pass band), no more than, s 1
GENERAL SPECIFICATIONS OF MAIN UNIT
AC power supply voltage, V 100~240
Consumption power, not more than, W 100
Main unit dimensions, mm 474 x 415 x 149
Main unit weight, kg 12
Sirius (page 3 of 3)
WIRE LINES ANALYSER
...continued
ANALYSIS OF SOUND FREQUENCIES
Input signal frequency range, Hz 100 ~100000
Pass bands of input signal (at 3 dB level), kHz 25; 100
Dynamic range of input signal processing (taking into account input attenuator), not less than, dB 140
Sensitivity at input (at REMOTE jack, 25 kHz pass band, SNR 10 dB) no more than, µV 1
Frequency resolution for 25 kHz and 100 kHz pass bands, Hz 60; 240
Maximum amplitude of input signal (with input attenuator), V 20
Electronic attenuator of input signal, dB 20
AGC setting range, dB 40
Voltage bias setting range, V ±15, with step of 1
Input impedance at REMOTE jack, Ω 620
Input impedance when using Signal Switcher, kΩ 50
IMPULSE REFLECTOMETRY
Maximum probing distance (at Kv=1.5), m 0~6400
Probing distances (at Kv=1.5), m 50;100;200;400;800; 1600;3200;6400
Duration of probing impulses, ns 5;10;20;50;100;200; 500;1000
Averaging of measured values (number of probing impulses per measurement) 1;2;5;10;20;50;100; 200
Amplitude of probing impulses, V 5
Output impedance, Ω 50
Overlapped attenuation,dB 80
Distance measurement error, not more than, % 0.2
Setting range of shortening coefficient (Kv) 1.0~3.0 with step of 0.01
x-shift (for Kv=1.5), m 0~6400
MEASUREMENT OF WIRE CIRCUITS PARAMETERS
DC voltage, V 0.001~100
AC voltage, V 0.001~100
Voltage of low frequency current, V 0.01~1
Voltage of high frequency current, V 0.01~1
Impedance, Ω 10-1~108
Capacitance, F 10-12~10-4
Inductance, H 10-3~102
Priboi (Acoustic System for Sirius)
SIRIUS ACCESSORIES
Characteristics of the device allow using it as part of instrumentation systems. The PRIBOI can be employed as a standalone device as well as in conjunction with the SIRIUS.
The PRIBOI is a loudspeaker with a built-in generator, placed on the speaker backside. There are jacks for connecting power and input signal cables. Volume control is on the front side of the loudspeaker.
Loudspeaker housing and generator are electromagnetically shielded.
THE DEVICE GENERATES AND RADIATES ACOUSTIC SIGNALS:
When operating with the built-in generator:• Tonal signal with 1000 Hz frequency;• White noise in 125 - 8000 Hz frequency band.
When operating with an external generator:• Tonal and noise signals in 20 Hz -20 kHz frequency band.
THE DEVICE PROVIDES SOUND PRESSURE:• 94 dB in white noise band;• 104 dB on 1 kHz frequency.• The PRIBOI is powered by the mains (220 ± 10 V).
The PRIBOI active acoustic system for Syrius is designed for generation of various tonal and noise signals, required for:
• Testing and measuring parameters of audio- and vibro-isolating properties of rooms, constructions and engineering services;
• Testing effectiveness of acoustic and vibroacoustic noise masking;
• Special examinations of main and auxiliary information processing equipment;
• Evaluation of acoustic and vibroacoustic signals characteristics with octave and third-octave analysis;
• Certification of protected premises.
Kassandra-21K (page 1 of 3)
RADIO MONITORING AND SIGNAL ANALYSIS
Unique combination of innovative solutions and advanced RadioInspector softwareExtended bandwidth of up to 21,000 MHz. Radio monitoring without VHF converters.Maximum scanning rate over 2,000 MHz/s within 20 kHz monitoring bandwidth. Dynamic range over 113 dB.Spectrum purity of internal tuners in HF and VHF bandwidth. No damaged frequencies and internal moire components.Automated radio emission classification and function of analysing digital communication standards.
Remote control via shared LAN or WAN.
RInspectorRT software features:
• easily adaptable user interface with unique functions and broad settings.
• task packages generated for scanning within the operating bandwidth can include any number of serially processed tasks, each with its own parameters assigned;
• panorama of current, maximum, minimum and averaged values of received signals;
• spectral pattern – 2D or 3D time-distributed panorama without any recording time limitations;
• marker and cursor measurements;
• saving and delayed analysis functions; any saved task can be re-run and further recorded into the
panorama data base;
• function of saving the reference panorama and panorama benchmarking analysis;
• diverted reception technique using an antenna switch;
• adjustable threshold line; adjustable and dynamic threshold;
• list of signals exceeding the threshold;
• frequency assignment data base and associated processing tools including a tailored calculator;
• HF spectrum analyser for real-time analysis of individual signals;
Kassandra-21K (page 2 of 3)
RADIO MONITORING AND SIGNAL ANALYSIS
...continued
• LF analysis – oscilloscope, low-frequency spectrum analyser, octave analyser, audio recording including
5-second information section before the recording, analysis and editing of saved data;
• automated response to detection: audio signal recording, signal analysis, in particular, for belonging
to analogue TV signals;
• additional analysis of detected signals (numeric and graphic);
• generation of reports on analysed frequency bandwidths and detected signals; export into Microsoft
Word®, Microsoft Excel®, text and graphic files;
• additional receiver control for independent low-frequency analysis.
• 4-link HF switch (up to 6 GHz);
• additional low-frequency input (up to 30 MHz), VHF antenna included in the delivery package;
• user-friendly interface, user-defined window settings, help, prompt messages
• one-click scalable spectral panorama;
• scalable and scrollable 2D and 3D spectral pattern (waterfall);
• adjustable threshold
• list of detected signals with statistics viewer;
• up to 8 MHz real-time spectrum analyser without any time limitations;
• automated processing of detected signals;
• control panel for an additional receiver;
• low-frequency oscilloscope, spectrum analyser, octave analyser;
• IQ data and demodulated AM and FM signal recording;
• frequency assignment data base and a tailored calculator;
• functional scalability by adding extra options.
Optional software modules extend analysing capabilities of RInspectorRT:
• RInspectorWiFi software detects Wi-Fi equipment and analyses Wi-Fi networks.
• D-Test option allows:
- Automated identification and analysis of
DECT, TETRA, GSM, Bluetooth, DMR, APCO25, DRM, DVB; - Analysis of GSM, DECT and Bluetooth network topology;
- Demodulation of APCO25, DMR(MOTOTRBO), DRM;- Display of PAL/SECAM/NTSC TV;- Digital signal analysis (vector diagram, filtration, decimation
and digital signal shift in vectors (I/Q)).
• RInspectorRP – specialised software for post analysis of recorded data on independed PC;
Kassandra-21K (page 3 of 3)
RADIO MONITORING AND SIGNAL ANALYSIS
Technical specifications:
Radio frequency parametersLW inputSwitched HF inputs (4)VHF input
0.009 - 30 MHz24 – 6,000 MHz6,000 – 21,000 MHz
Sensitivity Minus 144 dBm/Hz
Dynamic range 113 dB
Maximum frequency resolution 8 Hz
Maximum scanning rate over 2,000 MHz/s
Power supplyMainsAutonomous
100-240V, 50Hz adapterBuilt-in battery operation time 1.5 hours
Main unit dimensions 500×350×120 mm
Main unit weight 5.8 kg
...continued
VoronOPTICAL CAMERAS DETECTOR
Main features:
• Technical solutions used in the VORON (roof
prism and translucent optics) allowed to
make its design exceptionally compact by
retaining excellent optical characteristics:
high magnification, wide field of view and
exceptional image quality.
• Efficient impulse source of power supply
ensures a long operation time from one AA-
type battery (1,5 V).
• VORON case is made of aluminum alloy; it
has a hand strap and soft rubber eyeshade.
• The device is easy-to-use and does not
require any special skills.
VORON is designed for a quick detection of
concealed micro video cameras, including those with
pinhole lenses.
The principle of detection is based on effect of light
reflection or “return flare”. Thus, when a concealed target
is detected, there is a bright red spot (reflection from a
video camera lens) in the VORON’s field of vision.
Detecting distance of concealed video cameras with
pinhole lenses (diameter of 1mm) can be from 1m to 20m
depending on operational conditions. VORON employs
LED illumination of targets what makes it a safe-to-use
device for operator (unlike laser illumination).
Operation on optical basis, but not radio frequency
range, allows this device to detect any optical device
regardless of its operating mode (on/off) and data
transmission type (radio or cable). Therefore, a radio
interference, electromagnetic shield, masking gauze or
lens hood does not reduce the likelihood of detection.
Delivery set:1. Voron device2. Clothing3. Hand strap4. Packing box
Technical specifications:
Magnification 5x
Angle of view, grad 12
Diopter correction range ± 4
Diameter of exit pupil, mm 4,5
Voltage 1.5 V
Running time on one battery 6 hours
Dimensions 50 x 68 x 140 mm
Weight 330 g
LadyaACOUSTIC NOISE GENERATOR FOR CELL PHONES
LADYA-D
LADYA-4
LADYA-10
Protection for 10 cell phones
Standarts detected GSM 900/1800/3 G / Wi - Fi / Bluetooth
Protection type acoustic noise
Power supply 220 V mains
Other features IR remote activation
Protection for 1 cell phone
Standarts detected GSM 900/1800/3 G /4 G / Sky link / Wi - Fi / BT
Protection type acoustic noise
Power supply 220 V mains
Ladya - product series for acoustic protection of cell phones against unauthorised audio transmission.
Cell phone is placed into specially prepared enclosure. In case of remote activation of cell phone microphone
there is only one de-masking sign - change of electromagnetic field when cell phone tries to transmit audio
information. When unauthorised transmission is detected Ladya starts generating acoustic noise by means
of speaker inside its enclosure. Noise is passed directly to microphone of cell phone which is placed inside
Ladya and blocks all possible acoustic voice leak from surrounding environment.
Protection for 4 cell phones
Standarts detected GSM 900/1800/3 G / Wi - Fi / Bluetooth
Protection type acoustic noise
Power supply 4 Ah Li-Ion battery
Technical specifications:
Quantity of channels 1
Number of transducers (max) 4
Transducer impedance 8 ±2 Ohm
Dimensions 82 x 67 x 22 mm
Weight no more than 0,5 kg
LGS series (LGS-403) (page 1 of 2)
VIBROACOUSTIC PROTECTION
Vibroacoustic and acoustic noise interference protection
The vibroacoustic and acoustic interference system is designed to counteract special unauthorized data
retrieval devices that use the room’s walling as leak channels. Such devices include:
• electronic and acoustic stethoscopes that are used for tapping through ceilings, floors and walls;
• wired and wireless microphones mounted on the walling or water and heating pipes;
• laser and microwave data retrieval systems that operate through the window openings.
LGS products enables protection through generating broadband vibroacoustic noise interference on the
potentially hazardous room structures. Vibroacoustic noise interference is created by the generator and
transmitted to the structures through the vibration transducers. The Product also supports installation of an
acoustic radiator (loudspeaker) for protection of closed air spaces (air ducts, wells, etc.).
LGS-403 is a single-channel noise generator. The impedance of electromagnetic vibration transducers
constitutes 8 Ohm. The generator supports parallel or sequential connection of up to 4 electromagnetic
vibration transducers and of an acoustic radiator in such a way, that the overall load impedance would reach
8 ±2 Ohm. Up to 4 vibration transducers can be connected in total.
LGS-403 - 1 vibroacoustic channel - 4 transducers
Technical specifications:
Quantity of channels 2
Number of transducers (max) 32
Transducer impedance 8 ±2 Ohm
Working frequency band 9...11200 Hz
Distance Control By cable. Allows remote switch On/Off
Dimensions 115x145x40 mm
Power Supply 220 V, 50 Hz
LGS-404 (page 2 of 2)
VIBROACOUSTIC PROTECTION
Following transducers are available for LGS series of
vibroacoustic noise generators:
• LVP-2s vibration transducer is designed to generate
vibrations in various structural components (walls, ceilings,
floors) enclosing the allocated room;
• LVP-2t vibration transducer is designed to generate
vibrations in window’s glass and utilities (piping) that go
beyond the allocated room;
• LVP-2o is designed to generate vibrations in the glass of
the windows enclosing the allocated room.
• Acoustic noise - any 8 Ohm speaker could be used on
separate channel.
LGS-404 - 2 vibroacoustic channels - 32 transducers
Dimensions less than 40x25 mm
Weight less than 120 g
LGS-404 is a two-channel noise generator that supports connection of up to 16 transducers per channel. A
total of 32 transducers can be connected to the product. The product can also work with acoustic transducers
(dynamic radiators, acoustic systems, loudspeakers etc.). The terminals’ connection pattern depends on the
desired protection level and can be represented by the parallel, sequential or combined connection of the
required number of transducers.
Technical specifications:
Signal level at power cord plug in the frequency band of 10 - 150 kHz and receiver bandwidth of f=200 Hz at least 40 dBµV
Signal level at power cord plug in the frequency band of 0.15 - 30 MHz and receiver bandwidth of f=9 kHz at least 45 dBµV
Signal level at power cord plug in the frequency band of 30 - 300 MHz and receiver bandwidth of f=120 kHz at least 50 dBµV
Generator output signal level in the frequency band of 300 - 1800 MHz and receiver bandwidth of f=120 kHz at least 50 dBµV
Interspectrum correlations factor no more than 2
LGS-221220 V MAINS NOISE GENERATOR
220 V power grids Protection. AC circuits pose a double threat. First of all, acoustic data can be leaked
through the AC circuit (220 V). And secondly, there is a threat of information signals leak from office equipment.
There exist passive and active techniques for AC (220 V) protection against unauthorized data retrieval:
• Passive 220 V circuits protection implies using anti-interference line filters. Such filters weaken any
signals in the frequency band of 0.01-1,000 MHz with the efficiency of at least 60 dB and, thus, do not
let the information signals generated in office equipment get through. Besides, a correctly installed filter
also protects office equipment from the harmful effect of external interference. It’s worth mentioning
that efficient operation of anti-interference filters requires high-quality grounding.
• Active AC circuits (220 V) protection techniques imply generation of a noise signal exceeding the
information signals and signals of information retrieval devices in level by special generators. Such noise
signals are supplied to the 220 V circuit and to the ground circuit. These generators produce noise for 220
V circuits and ground circuits.
LGS-221 is an information security device that is designed to actively protect informatization equipment
against information leaks through the power grid and ground system. The Product provides protection
against data leaks through the 220 V single-phase three-wire power grid with the frequency of 50 Hz by
generating broadband noise interference in all the masking interference conductors in power supply and
ground circuits in the frequency band of 0.01 – 1,800 MHz.
Power consumption no more than 40 W
Power voltage ~ 220 V / 50 Hz
Dimensions 188 x 110 x 70 mm
Weight no more than 0,5 kg
Pilot-MEXPLOSIVE DETECTOR
Pilot-M has unique technical specifications and can
detect both vapors and determine a quantity of explosives
indoors or at any means of transport (cars, planes, trains,
ships and other). Detection is conducted by taking air
samples from inner space of inspected objects and their
subsequent analysis.
Remote tier with a grid thickener (part of delivery set) allows
to take samples in dusty and smoky areas. Furthermore,
there is a method of taking samples by special napkins,
that are later warmed up in a sample heater, which is also
added to a delivery set.
Pilot-M allows detecting track quantities of explosive based upon TNT, NG, EGDN, PENT (PETN), RDX, HMX,
Tetril, cellulose nitro compound gunpowder, including the ones on their base:
• Nitroglycerine (NG), EGDN, trinitrotoluene (tol, trotyl, TNT), PENT (tetranitrapentaerythrit,
pentaerythrittetranitrate, Pentrit, PETN), hexogen (RDX), oktogen (HMX), tetryl (Tetril),
threeacetonethreeperoxide (Cyclethreeacetonethreeperoxide, TATP) and nitrocellulose powders,
including explosive mixes: Semtex and other plastic and elastic explosives on the basis of RDX, PENT or
their mixture
• B-type compositions (ТГ-20, ТГ-40, ТГ-60, МС, ТГАФ)*,
• C-type mix (С1, С2, С3, С4, ПВВ-4, ПВВ-5А, ПВВ-7, ПВВ-12М, ЭВВ-11, ЭВВ-32 and etc.)*,
• Н-6, HBX, Minol-2, Amatol, Primacord, Primasheet, Tetritol, Tritonal, Cordit N, А-IX-1, А-IX-2, А-IX-20,
• explosives of Octols & Ocfols families and some other substances.
*- explosive of Russian origin
Technical specifications:
Sensitivity threshold (TNT sample) at 20 ± 2 °С, non less than, g/cm3 10-13
Response time, sec 1
Maximum distance between VD nozzle and examined object, mm 30
Alarm indication Visual and audible
Dimensions, mm 300 х 180 х 90
VD mass (incl. battery), kg 2
Power source DC 6V rechargea-ble battery
The device construction and unique analysis of algo-rithms provide with high precision and noise reduction.
In contrast to analogue equipment Pilot-M doesn't con-tain radioactive source and is absolutely safe for opera-tor and environment. Therefore, there are no limitations for purchasing, keeping, transporting, and utilization of the device.
Pilot-M1 uses special software allows comparing reg-istered spectrum to typical spectrum of pure and mixed explosives and sending it to a remote PC.
Anker-4EEXPLOSIVE TIMING DEVICES DETECTOR
Anker-4E detects various timing devices:
mechanical, electromechanical, electronic, as well as
other electronic devices and gears by their electric,
magnetic, acoustic and vibrating emissions.
Detects:• Electromechanical timing devices at an up to
40 cm range.
• Electronic timing devices at an up to 10 cm
range.
• Radio signal receivers at an up to 15 cm range.
Application:• Suspicious items inspection – RC IED or
explosive devices with clock retarders.
• Searching for persons hidden in shelters.
• Aircraft inspection.
Main features• Detection of periodic rhythms of mechanical
and electronic timers in improvised explosive
devices (I.E.D.).
• Detection of electronic timers, including
electronic wrist-watch based.
• The device is simple in use, lightweight and
compact.
• The device also has the capability to inspect
closed packages and handbags with the help
of a needle-shaped acoustic microphone.
• Test targets (mechanical, electromechanical
and electronic) are available.
• Can be used in places where active radio-
electronic equipment is not permitted
Technical specifications:
Indication headphones
Power supply 4 x AA cell
Continuous operation time not less than 30h
Dimensions (length/diameter) 510mm / 34mm
Operational temperature range +5º C…+40º C
Weight (ready for operational / in standard packing) 0.65kg / 2.4kg
Norka X-Ray (page 1 of 2)
X-RAY INSPECTION SYSTEMS
NORKA has a wide range of applications: customs,
law enforcement, airport security and other areas.
It is used for:
• Inspection of mail, parcels and small articles
• Detection of weapons, bombs, wires and
explosive devices in various packaging
• Detection of concealed eavesdropping devices
in furniture, office equipment, etc.
• Non-destructive testing and evaluation
The NORKA X-ray system is easy to use, reliable and
completely safe in operation. It provides excellent
detecting capability with no harmful effects to its
users or servicepersonnel.
NORKA is a unique portable X-ray inspection
system with a minifocus and microfocus constant
potential X-ray source. The voltage can be adjusted
from 20 to 160kV. This allows inspecting objects
made from different materials with various density
and thickness (20-70kV is the optimal voltage for
checking mail and thin objects, while 100-160kV
works best for baggage and thick objects). One
of NORKA’s advantages is its ability to inspect
areas of an object in fine details using geometric
magnification (up to 40 times).
Dual energy option allows recognizing organic and inorganic objects.
Norka X-Ray (page 2 of 2)
X-RAY INSPECTION SYSTEMS
The microfocus X-ray unit has a 30-micron focal spot rather than a 1 mm spot used in conventional X-ray
systems. In this case resolution attains an unprecedented 25 micron of a copper wire equivalent. Moreover,
the distance between an object and the X-ray source can be minimal, down to a few centimeters or even a few
millimeters when using geometric magnification.
The images are reproduced on a display screen of the control unit in a positive/ negative form, pseudo colours,
with enhanced contrast or in dual energy mode. Zooming in on any of the nine areas of the screen allows
better identification. Obtained images can be stored in the control unit memory for further investigation or
reference (up to 30,000 images). Stored images can also be edited and provided with additional text, graphics
and voice information.
If necessary, these images can be rewritten from the D:\images directory of a “BU-4” control unit to a USB flash
drive. Universal power supply (85 - 240 VAC 50/60Hz) allows easy operation anywhere in the world. This is the
only system on the market that works from -20°С to +50°С with humidity up to 90%.
The NORKA X-ray system is delivered in two handy carrying bags or in one case.
Technical specifications:
X-RAY UNIT RE-160 RE-120 RE-150MN RAP 220-5
Operation mode 5-25 second exposures in single energy mode
Max. X-ray tube voltage, kV 160 120 150 220
Focal spot size, μm 800 600 80 2000
Resolution (copper wire), μm 80 60 40 80
Total penetration (Al equivalent), mm 120 65 80 200
Total penetration (Fe equivalent), mm 40 24 20 60
X-RAY IMAGE CONVERTER
Сamera unit Digital - SKB-3D 1280х1024, 14 bit
Interchangeable converter - screeningarea, mm
“PR-4” - 190х250
“PR-5” - 300х400 (standard)
PR-6” - 410х550
CONTROL UNIT “BU-4”
Display 12” colour TFT touch screen display
Memory size (image number ) 30 000
Battery life 2 hours, or 60 X-ray image acquisitions
Operating temperature - 20о С to +50о С (-4о F to +122о F)
Relative humidity 90 % (35о С / 95о F)
Weight, kg less than 29 (Standard system configuration (NORKA with RE-150MN)
Inspection Mirrors Overview INSPECTION MIRRORS
We are glad to announce that SEKOTECH LTD expanded its product range and is now ready to offer high
quality inspection mirrors commonly used by safety and security authorities like police, border control &
guard agencies, anti-terrorism, rescue, other private security agencies and etc.
Because of high quality materials and firm construction the inspection mirrors can be used under any weather
and light conditions. Therefore, depending on customer’s needs and purpose we can offer a wide array of
modifications and packages available:
• Compact, pocket mirrors that can be easily & quickly assembled and used for object inspection.
• Inspection mirrors with telescopic bar (adjustable handle): from 60 cm and up to 300 cm length, modifiable
according to customer needs.
• A regular or LED flashlight can be mounted to the inspection mirror’s handle or inside of it.
• Reflectors can be replaced with various sizes and shapes (circle, square).
• We can also offer a large convex wide-angle mirrors on wheels dedicated for vehicle bottom inspection.
Moreover, these inspection mirrors can be produced according to client needs and of various size, shape and modification.
Please find several examples below. Since we are able to offer even more types than presented here we
encourage you to get in touch with us.
IMFL-1510 VUIM-LED-60IMLED-1500
IMFL-1510 With Telescopic Bar
INSPECTION MIRRORS
Inspection kit consists of four section ergonomically designed robust telescopic bar with mounted flashlight
bracket. Handle is covered with the insulating material. Kit includes three glass mirrors.
IMFL-1510 inspection mirror kit is
used for visual inspection of hard
to reach places, in various lighting
conditions.
Designed for: • Security services• Customs• Police• Rescue services• TSCM teams
Technical specifications:
The length of the telescopic arm (extended) 1510 mm
The length of the telescopic arm (folded) 525 mm
Mirror tilt 0 ... 1150
Mirror size (mirror 1) Ø 142 mm
Mirror size (mirror 2) Ø 70 mm
Mirror size (mirror 3) 68 x 126 mm
Power source 2 x D type batteries
Light source Krypton bulb
Weight 690 g
Delivery set:1. Telescopic arm with hand strap2. Mirror - 142 mm diameter3. Mirror - 70 mm diameter4. Mirror - 68 x 126 rectangle5. Flashlight6. Packing bag
IMLED-1500 Telescopic Bar + LED Light
INSPECTION MIRRORS
Technical specifications:
The length of the telescopic arm (extended) 1500 mm
The length of the telescopic arm (folded) 505 mm
Mirror tilt 0 ... 1150
Mirror size (mirror 1) Ø 142 mm
Mirror size (mirror 2) 68 x 126 mm
Power source 3 x AA type batteries
LED illuminator 6 LEDs
Weight 750 g
Delivery set:1. Telescopic arm with embedded
LED illuminator and hand strap2. Mirror - 142 mm diameter3. Mirror - 68 x 126 rectangle4. Packing bag
D-LED-1500 inspection mirror kit is used for visual inspection of hard
to reach places, in various lighting
conditions.
Designed for: • Security services• Customs• Police• Rescue services• TSCM teams
Inspection kit consists of four section ergonomically designed robust telescopic bar with embedded LED
illuminator. Handle is covered with the insulating material. Kit includes two glass mirrors. Embedded
illuminator is fitted with 6 high luminosity LEDs and has two power modes.
VUIM-LED-60 Vehicle Inspection
INSPECTION MIRRORS
Technical specifications:
Carriage dimensions 344 x 374 mm
Mirror dimensions 290 x 320mm
Handle length 1200 mm
Power source 6 AAA type batteries
LED panel 60 LEDs
Weight 4 kg
Delivery set:1. Mirror carriage2. Light source with 60 LEDs3. Handle with hand strap4. Packing bag
A robust under vehicle search mirror, designed for detailed searching of the
underside of vehicles in conditions of insufficient illumination.
The search mirror has a large convex wide-angle mirror for maximum
observation, which is mounted on a tough wheeled base, and a detachable
LED lighting panel with variable illumination brightness. The LED panel is
mounted on a carriage by magnetic holders. If necessary, the LED panel can
be detached and used as a lantern.
The carriage is moving on 4 small dimension rotary wheels, which makes it
possible to roll the carriage under vehicles of low clearance. Each wheel rotary
unit is equipped with 2 bearings, which allows to turn the carriage without
jerking.
ZD seriesINSPECTION MIRRORS
Their ability to facilitate visual inspection of hard-to-
reach places including the dark ones can be used:
• by technical structures for examination of a state of
various objects;
• by customs services for inspection and supervision
of passenger traffic and freight transport;
• by rescue services when eliminating the effects of
emergency situations (inspection of blockages and
hard-to-reach places);
• for inspection of municipal engineering objects
(wells, elevator equipment, collecting channels, etc.);
• when performing examination and maintenance
works in transportation facilities;
• by rescue and security services for performing
special operations.
Main features:• Low-weight LED illuminating lamp supplied by
three rechargeable batteries (AAA type). The
lamp can be readily extracted from a holder and
used independently;
• Set of mirrors of various sizes and shapes (at the
customer’s option);
• Two types of used optical materials: glass and
reflecting plastic;
• Simple and reliable mirror holding/inclination
assembly;
• Working length is up to 2.5 m;
• Monocular for detailed examination of distant
objects with an 8X magnification;
Delivery set:1. Telescopic arm;2. Mirrors: rectangular mirror and two round ones;3. Illuminating lamp;4. 8X monocular;5. Two sets of rechargeable batteries;6. Charger;7. Packing bag.
JSC SekotechAvizu str. 2-1408435 VilniusLithuania
VAT No. LT100007374115
Phone +47 967 44174E-Mail info@sekotech.comWebsite www.sekotech.comSkype sekotech
AM FM PSK FSK ...WiFi
2.4 GHz
4G
Bluetooth
GSM
UMTS CDMA DECT