Transcript of Compact Disc Player C-7000R - Onkyo...blade or the third prong are provided for your safety. If the...
Important Safety Instructions
1. Read these instructions. 2. Keep these instructions. 3. Heed all
warnings. 4. Follow all instructions. 5. Do not use this apparatus
near water. 6. Clean only with dry cloth. 7. Do not block any
ventilation openings. Install in
accordance with the manufacturer’s instructions. 8. Do not install
near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
15. Damage Requiring Service Unplug the apparatus from the wall
outlet and refer servicing to qualified service personnel under the
following conditions: A. When the power-supply cord or plug is
damaged, B. If liquid has been spilled, or objects have
fallen
into the apparatus, C. If the apparatus has been exposed to rain or
water, D. If the apparatus does not operate normally by
following the operating instructions. Adjust only those controls
that are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often
require extensive work by a qualified technician to restore the
apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in any way,
and
F. When the apparatus exhibits a distinct change in performance
this indicates a need for service.
16. Object and Liquid Entry Never push objects of any kind into the
apparatus through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric
shock. The apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases shall be placed
on the apparatus. Don’t put candles or other burning objects on top
of this unit.
17. Batteries Always consider the environmental issues and follow
local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation, such
as a bookcase or rack, ensure that there is adequate ventilation.
Leave 20 cm (8") of free space at the top and sides and 10 cm (4")
at the rear. The rear edge of the shelf or board above the
apparatus shall be set 10 cm (4") away from the rear panel or wall,
creating a flue-like gap for warm air to escape.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING RISK OF ELECTRIC SHOCK
DO NOT OPEN RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
Precautions 1. Recording Copyright—Unless it’s for personal
use
only, recording copyrighted material is illegal without the
permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user- serviceable. If
you cannot turn on the unit, contact your Onkyo dealer.
3. Care—Occasionally you should dust the unit all over with a soft
cloth. For stubborn stains, use a soft cloth dampened with a weak
solution of mild detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they may damage the
finish or remove the panel lettering.
4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from
country to country. Make sure that the voltage in your area meets
the voltage requirements printed on the unit’s rear panel (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit from the AC
power source. Make sure that the plug is readily operable (easily
accessible) at all times.
Some models have a voltage selector switch for compatibility with
power systems around the world. Before you plug in such a model,
make sure that the voltage selector is set to the correct voltage
for your area.
Pressing the [POWER] button to select OFF mode does not fully
disconnect from the mains. If you do not intend to use the unit for
an extended period, remove the power cord from the AC outlet.
5. Preventing Hearing Loss Caution Excessive sound pressure from
earphones and headphones can cause hearing loss.
6. Batteries and Heat Exposure Warning Batteries (battery pack or
batteries installed) shall not be exposed to excessive heat as
sunshine, fire or the like.
7. Never Touch this Unit with Wet Hands—Never handle this unit or
its power cord while your hands are wet or damp. If water or any
other liquid gets inside this unit, have it checked by your Onkyo
dealer.
8. Handling Notes • If you need to transport this unit, use the
original
packaging to pack it how it was when you originally bought
it.
• Do not leave rubber or plastic items on this unit for a long
time, because they may leave marks on the case.
• This unit’s top and rear panels may get warm after prolonged use.
This is normal.
• If you do not use this unit for a long time, it may not work
properly the next time you turn it on, so be sure to use it
occasionally.
• When you’ve finished using this unit, remove all discs and turn
off the power.
9. Installing this Unit • Install this unit in a well-ventilated
location. • Ensure that there’s adequate ventilation all
around
this unit, especially if it’s installed in an audio rack. If the
ventilation is inadequate, the unit may overheat, leading to
malfunction.
• Do not expose this unit to direct sunlight or heat sources,
because its internal temperature may rise, shortening the life of
the optical pickup.
• Avoid damp and dusty places, and places subject to vibrations
from loudspeakers. Never put the unit on top of, or directly above
a loudspeaker.
• Install this unit horizontally. Never use it on its side or on a
sloping surface, because it may cause a malfunction.
• If you install this unit near a TV, radio, or VCR, the picture
and sound quality may be affected. If this occurs, move this unit
away from the TV, radio, or VCR.
10. Moisture Condensation Moisture condensation may damage this
unit. Read the following carefully: Moisture may condense on the
lens of the optical pickup, one of the most important parts inside
this unit. • Moisture condensation can occur in the following
situations: – The unit is moved from a cold place to a warm
place. – A heater is turned on, or cold air from an air
conditioner is hitting the unit. – In the summer, when this unit is
moved from an
air conditioned room to a hot and humid place. – The unit is used
in a humid place.
• Do not use this unit when there’s the possibility of moisture
condensation occurring. Doing so may damage your discs and certain
parts inside this unit.
If condensation does occur, unplug the power cord and leave the
unit for two to three hours in the room temperature.
4 En
This unit contains a semiconductor laser system and is classified
as a “CLASS 1 LASER PRODUCT”. So, to use this model properly, read
this Instruction Manual carefully. In case of any trouble, please
contact the store where you purchased the unit. To prevent being
exposed to the laser beam, do not try to open the enclosure.
CAUTION: CLASS 1M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. THIS PRODUCT
UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
The label on the right is applied on the rear panel.
1. This unit is a CLASS 1 LASER PRODUCT and employs a laser inside
the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover. Refer servicing to qualified personnel.
For U.S. models FCC Information for User
CAUTION: The user changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures: • Reorient or relocate the receiving
antenna. • Increase the separation between the equipment and
receiver. • Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. • Consult
the dealer or an experienced radio/TV
technician for help.
For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003. For models having a power cord with a
polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
Modèle pour les Canadien REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles
dont la fiche est polarisée: ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
For British models Replacement and mounting of an AC plug on the
power supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral Brown: Live
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows: The wire which is coloured blue
must be connected to the terminal which is marked with the letter N
or coloured black. The wire which is coloured brown must be
connected to the terminal which is marked with the letter L or
coloured red.
IMPORTANT The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must approved by ASTA or
BSI to BS1362 and have the same ampere rating as that indicated on
the plug. Check for the ASTA mark or the BSI mark on the body of
the fuse. If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse in
the plug.
For European Models
Declaration of Conformity
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH K. MIYAGI
declare in own responsibility, that the ONKYO product described in
this instruction manual is in compliance with the corresponding
technical standards such as EN60065, EN55013, EN55020 and
EN61000-3-2, -3-3.
5 En
and WMA CD*
• Separate Digital/Analog Circuitry • Separate Massive Transformers
for Digital
and Analog Circuitry (Toroidal Transformer for Analog
Circuitry)
• Thermally Regulated High-Precision Clock • Silent Disc Mechanism
with Solid Die-Cast
Aluminum Tray • Separate Anti-Vibration Aluminum Panels for
Top, Front, and Sides • Side-mounted Circuit Board Construction
to
Reduce Vibration • PLL Ultra Low Jitter Technology • Separate TI
(Burr-Brown) 192 kHz/24-Bit
DACs (PCM1792) for L/R Channels • Pure Analog Mode • Transport Mode
for Digital Output • AES/EBU Balanced Digital Output with XLR
Connector • 3 Digital Outputs (Optical, Coaxial and
AES/EBU) • Gold-Plated, Machined Solid Brass, Wide
Pitch Audio Outputs • Display Dimmer (Normal/Dim/Off)
* Discs should be properly finalized.
6 En
Technologies DIDRC (Dynamic Intermodulation Distortion Reduction
Circuitry) Since the advent of digital audio, the values of S/N
(signal-to-noise) ratio have risen significantly. However, it is
also recognized that in terms of perceived S/N, analog audio
sources are not inferior to digital sources. Generally, S/N
measures the ratio when sound is and not produced, but takes no
account of the noise generated during sound reproduction. For a
long time, Onkyo has focused and made extensive research on the S/N
when sound is produced (dynamic S/N). Using a mechanism that
captures the noise beyond audible range, it has been possible to
determine that both dynamic S/N and perceived S/N aggravate during
music reproduction. Although frequencies above 20 kHz are beyond
human hearing, it is well known that a beat can be perceived if
different signals are overlapped at such frequencies. During the
analog audio era, no significant signals were entering beyond the
audible range. However, the digital era has made recording beyond
the audible range possible and the generated beat is now
perceivable. With Onkyo’s DIDRC technology, a new approach is
introduced which prevents such beat from penetrating the audible
range.
Separate Digital/Analog Circuitry and Transformers To prevent
unwanted interference, the C-7000R employs physically separate
circuitry for digital and analog processing. In the same vein, the
player also features separate transformers for digital and analog
circuitry.
Thermally Regulated Super-Precision Clock The C-7000R boasts an
extremely precise clocking mechanism that controls and coordinates
the timing of all digital signal processes—rather like how a
conductor directs and coordinates the individual instruments of an
orchestra. The C-7000R uses a state-of-the- art crystal oscillator
that achieves a frequency deviation of ±1.5 ppm at room
temperature- much lower than with a conventional oscillator. Even
in surrounding temperatures of -30°C or +80°C the frequency remains
stable, with only ±0.5 ppm of additional frequency deviation.
PLL (Phase Locked Loop) Ultra-Low Jitter Technology Jitter is an
unwanted side-effect of the digital- to-analog conversion process
caused by fluctuations in the time domain of a digital signal. PLL
ultra-low jitter technology reduces jitter by comparing the input
and output phases of the digital signal and creating an accurate
clock waveform. This enhances the precision of digital signal
processing and noticeably improves perceived audio quality.
Side-mounted Circuit Board Construction Rather than being directly
connected to the chassis base, the circuit boards inside the
C-7000R are cushioned by internal struts and affixed to the front,
side, and rear panels. This method of construction prevents
vibrations from the chassis from adversely affecting the circuit
boards.
7 En
Block Diagram
8 En
Remote controller (RC-796C) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . (1) Batteries
(R03/AAA). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . (2)
Power cord (1.8 m/5.9 ft) . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (1) (Plug
type varies from country to country.)
Audio connection cable (0.8 m/2.6 ft) . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . (1)
* In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and operations are
the same regardless of color.
Remote controller and two batteries
Power cord
Audio connection cable
Thank you for purchasing an Onkyo Compact Disc Player. Please read
this manual thoroughly before making connections and plugging in
the unit. Following the instructions in this manual will enable you
to obtain optimum performance and listening enjoyment from your new
Compact Disc Player. Please retain this manual for future
reference.
9 En
Contents Introduction
Turning On/Off the Compact Disc Player
..........................................................21
Playing the Disc
.................................................................................................22
Selecting Files
(MP3/WMA)...............................................................................23
Setting the Display
Brightness...........................................................................24
Note
• If the remote controller doesn’t work reliably, try replacing the
batteries.
• Don’t mix new and old batteries or different types of batteries.
• If you intend not to use the remote controller for a long
time,
remove the batteries to prevent damage from leakage or
corrosion.
• Remove expired batteries as soon as possible to prevent damage
from leakage or corrosion.
To use the remote controller, point it at the compact disc player’s
remote control sensor, as shown below.
Note
• The remote controller may not work reliably if the compact disc
player is subjected to bright light, such as direct sunlight or
inverter-type fluorescent lights. Keep this in mind when
installing.
• If another remote controller of the same type is used in the same
room, or the compact disc player is installed close to equipment
that uses infrared rays, the remote controller may not work
reliably.
• Don’t put anything, such as a book, on the remote controller,
because the buttons may be pressed inadvertently, thereby draining
the batteries.
• The remote controller may not work reliably if the compact disc
player is installed in a rack behind colored glass doors. Keep this
in mind when installing.
• The remote controller will not work if there’s an obstacle
between it and the compact disc player’s remote control
sensor.
Install the compact disc player on a sturdy rack or shelf. Position
it so that its weight is evenly dispersed on its four legs. Do not
install the compact disc player in a place with vibration or an
unstable location.
Installing the Batteries
1 To open the battery compartment, press the small hollow and slide
the cover.
2 Insert the two supplied batteries (R03/AAA) in accordance with
the polarity diagram inside the battery compartment.
3 Replace the cover and slide it shut.
Using the Remote Controller
Approx. 16 ft. (5 m)30° off center (Left/Right)
Installing the Compact Disc Player
10 cm (4")
20 cm (8")
10 cm (4")
10 cm (4")
Getting to Know the Compact Disc Player
The page numbers in parentheses show where you can find the main
explanation for each item.
a ON/STANDBY button ( 21) Use this button to set the compact disc
player to On or Standby.
b Standby LED ( 21) Lights when the compact disc player is in
Standby mode.
c Remote control sensor ( 10) The sensor receives control signals
from the remote controller.
d Display ( 12) See “Display”.
e Disc tray ( 22) Insert discs into this tray.
f 0 button ( 22) Opens and closes the disc tray.
g 3 button ( 22) Use this button to pause disc playback. When
paused, this resumes playback.
h 2 button ( 22) Use this button to stop disc playback.
i 1 button ( 22) Use this button to play the disc.
j OUTPUT MODE button ( 32) Use this button to switch the audio
output signal between analog and digital (or both).
k POWER switch ( 21) This is the main power switch. When set to the
OFF position (@), the compact disc player is completely shutdown.
It must be set to the ON position (^) to set the compact disc
player to On or Standby.
l Display Off LED ( 24) Lights when the display is turned off.
Before entering standby mode with the ASb function, the Display Off
LED flashes 30 seconds before the ASb function starts
running.
m 7 button ( 22) Use this button to skip to the beginning of the
track being played. Press and hold down to fast reverse.
n 6 button ( 22) Use this button to skip to the beginning of the
next track. Press and hold down to fast forward.
Front Panel
a 1 indicator ( 22) Lights during playback.
b 3 indicator ( 22) Lights when playback is paused.
c MEMORY indicator ( 26, 27, 28) Lights during memory
playback.
d FOLDER indicator ( 23) Lights together with the folder
name.
e TRACK indicator ( 22) Lights together with the track number or
file name.
f TOTAL indicator ( 21) Lights when the total and remaining time of
the track are shown.
g REMAIN indicator ( 30) Lights when the remaining time of the
track is shown.
h RANDOM indicator ( 29) Lights during random playback.
i 1 indicator ( 25) Lights during repeat playback. “1” is shown
when only the currently playing track is repeated.
j Audio output indicators Indicate the type of audio output ( 32):
DIGITAL and/or ANALOG.
k MP3 indicator ( 21) Lights together with the folder name, file
number or file name which contains MP3 tracks.
l WMA indicator ( 21) Lights together with the folder name, file
number or file name which contains WMA tracks.
m Message area Displays various information.
Display
k l m
13 En
a AUDIO OUTPUT ANALOG L/R jacks Connect the analog audio in jack of
an amplifier or similar to this jack, using the supplied audio
cable.
b AUDIO OUTPUT DIGITAL AES/EBU jack This balanced AES/EBU output is
for connecting a component with a balanced AES/EBU input.
c AUDIO OUTPUT DIGITAL COAXIAL jack This coaxial digital audio
output is for connecting components with coaxial digital audio
inputs, such as preamplifier.
d AUDIO OUTPUT DIGITAL OPTICAL jack This optical digital audio
output is for connecting components with optical digital audio
inputs, such as preamplifier.
e AC INLET The supplied power cord is connected here. The other end
of the power cord should be connected to a suitable wall
outlet.
Rear Panel
cb eda
14 En
Remote Controller
k
l
j
m
n
g
h
i
f
e
b
c
d
a
You can also use the remote controller to control your Onkyo
C-7000R. For detailed information, see the pages in
parentheses.
a 8 button ( 21) Sets the compact disc player to On or
Standby.
b DIMMER button ( 24) Adjusts the display brightness.
c DISPLAY button ( 30) Displays information about the current input
source.
d RANDOM button ( 29) Used with the random playback.
e Playback mode buttons ( 22)
3 button Used to pause playback. When paused, this resumes
playback.
7 button Used to skip to the beginning of the track being
played.
1 button Used to play the disc.
6 button Used to skip to the beginning of the next track.
5 button Used to fast reverse the current song.
2 button Used to stop disc playback.
4 button Used to fast forward the current song.
f !/"/#/$ and ENTER buttons Used to select and adjust
settings.
g SEARCH button ( 29) Search for a folder on a disc containing MP3
or WMA tracks.
h SETUP button Used to change settings.
i Number buttons ( 24) Used to select tracks and the like.
j 0 button ( 22) Open and close the disc tray.
k OUTPUT MODE button ( 32) Use this button to switch the audio
output signal between analog and digital (or both).
l REPEAT button ( 25) Used with the repeat playback.
m MEMORY button ( 26, 27, 28) Used to begin or end memory
playback.
n CLEAR button Used to clear any numbers that have been entered
during numeric input. When making a memory setting, the selected
track is erased.
15 En
The compact disc player supports the following discs.
• Do not use discs designed for purposes other than audio, such as
CD-ROMs for PC use. Abnormal noise could damage the speakers or
compact disc player.
• The compact disc player supports CD-R and CD-RW discs. Note that
some discs may not playback because of the CD characteristics,
scratches, contamination or the recording state. A CD recorded with
an audio CD record will not playback unless it is finalized.
• Never use discs which have a special shape (such as hearts or
octagons). These types of discs could jam and damage the compact
disc player.
Some audio CDs with copy-control function do not comply with
official CD standards. These are special discs and cannot be played
with this compact disc player.
Hold discs by the edge, or by the center hold and edge. Avoid
touching the playback surface (surface with nothing printed on
it).
Do not attach paper or stickers, or write on the playback or label
surface of the disc. Take care not to scratch or damage the
disc.
Do not use discs with residue from cellophane tape, rental discs
with labels which are peeling off, or discs with decorative labels.
This type of disc could get stuck in the compact disc player, or
could damage the compact disc player.
Do not leave a CD-R/CD-RW having a label printed with an inkjet
printer in the compact disc player for a long time. The disc could
get stuck in the compact disc player, or could damage the compact
disc player. Remove the disc from the compact disc player when not
being played, and store it in a case. A freshly printed disc will
stick easily, and should not be played immediately.
If the disc is dirty, the compact disc player will have a hard time
reading signals, and the audio quality may drop. If the disc is
dirty, gently wipe off fingerprints and dust with a soft cloth.
Lightly wipe from the center outwards. To remove stubborn dust or
dirt, wipe the disc with a soft cloth dampened with water, and then
dry it with a dry cloth. Do not use cleaning spray for analog
records or antistatic agents, etc. Never use volatile chemicals
such as benzine or paint thinner as they can impregnate the disc
surface.
Moving the compact disc player from a cold room into a warm room,
or heating a cold room with a heater may cause waterdrops to form
inside the compact disc player. This is called condensation. Not
only does this cause malfunction, but it can also damage the
compact disc player or any inserted disc. Remove discs from the
compact disc player when not in use. If condensation appears,
unplug the power cord and leave the compact disc player more than 3
hours at room temperature.
Disc Note
Supported Discs
Handling Discs
Caring for Discs
About the Condensation
16 En
MP3 and WMA files recorded on a CD-R/CD-RW can be played with this
compact disc player. • Use discs which have been recorded following
the
ISO9660 Level 2 file system. (The supported directory depth is
eight levels, the same as ISO9660 Level 1) Discs recorded with the
hierarchical file system (HFS) cannot be played.
• Always close the disc tray.
Note
• A disc recorded with a recorder or personal computer may not play
in some cases. (Cause: Disc’s characteristics, damaged or dirty
disc, dirt on player’s lens, dew condensation, etc.)
• A disc recorded on a personal computer may not play because of
the application settings or environment. Record the disc with the
proper format. (Contact the application maker for details.)
• A disc with insufficient storage capacity may not play back
properly.
• Only MP3 files with the extension “.MP3” or “. mp3” are
supported.
• This compact disc player supports files recorded in MPEG 1 Audio
Layer 3 (32-320 kbps), with the sampling frequency of 32/44.1/48
kHz.
• Variable bitrates (VBR) between 32 kbps and 320 kbps are
supported. The time information during VBR playback may not display
correctly.
• WMA stands for “Windows Media® Audio”, an audio compression
technology developed by Microsoft Corporation USA.
• Only WMA files with the extension “.WMA” or “.wma” are
supported.
• Encode the WMA file with an application approved by Microsoft
Corporation USA. The file may not playback correct if encoded with
an unapproved application.
• Variable bitrates (VBR) between 32 kbps and 192 kbps (32/44.1/48
kHz) are supported.
• Copyright-protected WMA files cannot be played back. • WMA Pro,
Lossless and Voice are not supported.
* Windows Media is a registered trademark or trademark of Microsoft
Corporation in the United States and/or in other countries.
Playback of MP3 and WMA CDs
Playback of MP3 CDs
Playback of WMA CDs
Connections
Connections
Note
• Push plugs in all the way to make good connections (loose
connections can cause noise or malfunctions).
• To prevent interference, keep audio cables away from power cords
and speaker cables. • The compact disc player’s optical digital
jack has a shutter-type cover that opens when an optical plug is
inserted and closes when it’s removed. Push plugs in all the way. •
To prevent shutter damage, hold the optical plug straight when
inserting and removing. • The analog audio cable can be used
instead of the coaxial cable.
Plugging the AES/EBU cable Match the pins and insert the jack until
you hear a “click.” Make sure that the jack is locked by lightly
pulling the connection cable.
Unplugging the AES/EBU cable Pull out the connection cable while
holding down the button.
Cable and Jacks
Balanced AES/EBU This is a professional digital audio interface.
Balanced AES/EBU cables are used for better noise immunity and
longer cable runs. The maximum sampling rate for PCM output is 44.1
kHz/16 bit, 2ch.
Optical digital audio Optical digital connections allow you to
enjoy digital sound. The maximum sampling rate for PCM input is
44.1 kHz/16 bit, 2ch.
Coaxial digital audio Coaxial digital connections allow you to
enjoy digital sound. The maximum sampling rate for PCM input is
44.1 kHz/16 bit, 2ch.
Analog audio (RCA) Analog audio connections (RCA) carry analog
audio.
About Balanced Output (AES/EBU Jack)
OPTICAL
Orange
L
R
White
Red
Right!
Wrong!
Tip
• To reduce noise, do not tie the signal cable and power cable
together. Wire them so that they are away from each other.
Note
• Never disconnect the power cord from the compact disc player
while the other end is still plugged into a wall outlet. Doing so
may cause an electric shock. Always disconnect the power cord from
the wall outlet first, and then the compact disc player.
• Turning on the compact disc player may cause a momentary power
surge that might interfere with other electrical equipment on the
same circuit. If this is a problem, plug the compact disc player
into a different branch circuit.
• Do not use a power cord other than the one supplied with the
compact disc player. The supplied power cord is designed
exclusively for use with the compact disc player and should not be
used with any other equipment.
Connecting the Power Cord
Supplied power cord
To an AC wall outlet (Plug type varies from country to
country.)
1 Make sure that the main power of the compact disc player is
turned off.
2 Connect all of your components.
3 Connect the supplied power cord to the compact disc player’s AC
INLET.
4 Plug the power cord into an AC wall outlet.
19 En
This is an example of analog connection using the preamplifier
P-3000R. This is an example of digital connection using the
preamplifier P-3000R. Connect either of them.
Connecting a Preamplifier or Integrated Amplifier
Analog Connection
Preamplifier P-3000R
Compact Disc Player C-7000R
This is an example of AES/EBU connection using the preamplifier
P-3000R.
21 En
Tip
• After a certain period of warning up, the temperature of the
compact disc player’s components and internal temperature are
stabilized, and the sound will soften.
Note
• If the message “NO DISC” appears on the display, no disc
information is available.
• The compact disc player remembers the state when power was
previously turned OFF, and returns to the state.
Note
Turning On/Off the Compact Disc Player
POWER
ON/STANDBY
8
Turning On the Compact Disc Player
1 Set POWER to the ON position (^) on the front panel.
2 Press 8 to turn on the compact disc player. The compact disc
player comes on, the display lights, and the Standby LED goes
off.
You can also use compact disc player’s ON/STANDBY.
Total number of tracks
Turning Off the Compact Disc Player
1 Press 8 to set the compact disc player to Standby. The compact
disc player will enter Standby mode, and the Standby LED
lights.
You can also use compact disc player’s ON/STANDBY.
2 To completely shut down the compact disc player, set POWER to the
OFF position (@).
22 En
Tip
• Only alphanumeric characters in MP3/WMA CD information are
displayed correctly. Double-byte characters and other characters
appear as underscores.
• If a disc has been set in the tray, when the power of the compact
disc player is turned on, then it starts to play
automatically.
To Select Tracks Press 6 to select the next track/file or 7 to
select the previous track/file.
• If you press 7 during playback or while playback is paused, the
beginning of the current track/file is selected.
• If you select a track/file while playback is stopped, press 1 to
start playback.
• When 7/6 are pressed, the following Disc information is displayed
for MP3/WMA. (During playback) File number/File name → File name →
File number/playing time (Paused) File number/File name → File name
→ Folder number/File number
To Fast-Forward or Fast-Reverse During playback or while playback
is paused, hold down 4 to fast-forward or 5 to fast-reverse.
To Pause Playback During playback, press 3. The 3 indicator
lights.
To resume playback, press 1 or 3 again.
To Stop Playback Press 2 to stop playback.
To Eject the Disc Press 0 to open the disc tray.
Note
• For MP3/WMA CDs, you can select MP3/WMA files in other
folders.
Playing the Disc
1 Press 0 to open the disc tray.
Pressing 0 while the compact disc player is on Standby will turn on
the compact disc player and open the disc tray.
0 3
3, 7, 1, 6, 5, 2, 4
2 Place the disc on the tray with the label-side facing up.
When you want to listening to the 8 cm disc, place it in the center
of the tray.
3 Press 1 to start playback. The disc tray closes and playback
starts.
Track currently playing
Elapsed track time
23 En
For MP3/WMA CDs, files (MP3/WMA files) may be organized in a
hierarchically, with folders containing files and subfolders, as
shown below.
For the compact disc player, there are two modes for selecting
files (MP3/WMA files): Navigation mode and All Folder mode. In
Navigation mode, you can select files (MP3/WMA files) by navigating
through the folder hierarchy, moving in and out of folders and
subfolders. In All Folder mode, all folders appear at the same
level, making it easy to select folders regardless of the
hierarchy.
Note
• If you don’t select a specific MP3/WMA file or folder for
playback, all of the MP3/WMA files on the disc will be played in
numerical order starting with file #1 in parentheses.
Selecting Files (MP3/WMA)
In this manual, MP3/WMA files are referred to as files. Likewise,
folders (directories) are referred to as folders.
File #11
File #1
File #10
Folder #3
File #12
Folder #2
File #13
Folder #4
File #14
File #18
In Navigation mode, you can select files by navigating through the
folder hierarchy. This mode can only be used while playback is
stopped.
To cancel the procedure at any point, press 2 on the remote
controller.
Note
• The behavior of 2 on the compact disc player can be set from
“STOP KEY” ( 32).
Selecting Files in Navigation Mode
1 While playback is stopped, press " or 2. The compact disc player
enters Navigation mode and “[ROOT]” appears on the display.
76
!, ", #, $
ENTER
2 Press " or ENTER (front panel: 1). The first folder name in ROOT
appears on the display. If the disc contains no folders, the first
file name appears.
3 Use #/$ or 7/6 to select other folders and files at the same
level. To move up a level, press ! or 3 (front panel: 2). Folders
that don’t contain files or subfolders can’t be selected.
4 Press ENTER or " to move down a level (front panel: 1).
5 Use #/$ or 7/6 to select a file in the folder.
6 Press ENTER or 1. Playback will start with the specified file or
folder and continue until all of the files on the disc have been
played.
24 En
In All Folder mode, you don’t have to navigate the folder hierarchy
because all folders that contain files appear at the same level.
This mode can only be used while playback is stopped.
To cancel the procedure at any point, press 2.
To Select Folders and Files by Number 1. Use the number buttons as
shown in the examples
below to enter folder/file numbers.
2. Playback starts. When you enter folder number, playback will
start from the first file in the selected folder. If a folder
contains more than 99 files, single- and double-digit file numbers
must be preceded by zeros. For example, to specify file #8, press
8. To specify file #34, press >10, 3, and 4. To specify file
#134, press >10, 1, 3, and 4.
Note
• The behavior of 2 on the compact disc player can be set from
“STOP KEY” ( 32).
Selecting Files in All Folder Mode
1 While playback is stopped, press ! or 3 (front panel: press and
hold 2). The compact disc player enters All Folder mode, and “1-”
appears on the display.
2 Use #/$ or 7/6 to select the other folders. You can select any
folder that contains files.
76
!, ", #, $, ENTER
3 Press " (front panel: 1). The first file name inside the folder
appears.
Use #/$ or 7/6 to select the files within the folder.
To select another folder, press 3 again (front panel: 2), and then
use 7/6 to select it.
4 Press ENTER or 1 to start playback.
Playback will start with the specified file or folder and continue
until all of the file on the disc have been played.
To select: Press:
Folder/File #10
Folder/File #34
You can adjust the brightness of the compact disc player’s
display.
Note
• The display lights for a 5 seconds if you control any buttons on
the front panel or remote controller when the display brightness is
set to OFF.
Setting the Display Brightness
1 Press DIMMER repeatedly to change the brightness of the display
in sequence.
Normal → Dim → Off
25 En
Advanced Operations
Advanced Operations
In repeat playback, you can play an entire disc repeatedly, play
one track repeatedly, or combine it with memory playback to play
the playlist repeatedly, or random playback to play all of the
tracks on the disc in random order repeatedly.
Tip
• Repeat playback is cancelled when you press 0 to open the disc
tray.
• Repeat playback is cancelled when you press 8 or ON/STANDBY to
turn off the compact disc player.
Repeat Playback
REPEAT
1 Press REPEAT repeatedly to select Repeat All, Repeat 1 or Repeat
Off.
The “” or “ 1” indicator lights.
Repeat All → Repeat 1 → Repeat Off
Repeat-1 playback can’t be combined with memory playback, random
playback.
2 To cancel repeat playback, press REPEAT repeatedly until the “RPT
OFF” appears.
The “” or “ 1” indicator goes off.
indicatorRepeat All
Repeat Off
26 En
In memory playback, you can create a playlist of up to 25 tracks.
Memory playback can be set only when the playback is stopped.
To Change the Display While the memory setting operations, press
DISPLAY repeatedly to change the display information as follows:
Track number/Playlist number → Track number/Playing time → Track
number/Total playing time
To Select Other Tracks During Memory Playback
Use 7/6 to select other tracks during memory playback.
To Check the Playlist While playback is stopped, use 5/4 to scroll
through the playlist. Track number and play time are
displayed.
To Remove Tracks from the Playlist • While memory playback is
stopped, press CLEAR.
Each press removes the last track from the playlist. • The playlist
is deleted on changing the playback mode
(press MEMORY after stopping the playback).
To Cancel Memory Playback • Stop the playback, then press MEMORY to
change the
playback mode. The MEMORY indicator goes off, and memory playback
is cancelled.
• Memory playback is also cancelled by pressing 0 to open the disc
tray, 8 or ON/STANDBY to turn off the compact disc player.
Note
• If the total playing time is more than 99 minutes and 59 seconds,
“--:--” appears.
• You can add up to 25 tracks to the playlist. If you try to add
more, the message “MEM-FULL” appears.
Memory Playback (CD)
0
MEMORY
ENTER
CLEAR
1 Press MEMORY. The MEMORY indicator lights.
2 Use 7/6 to select the first track you want to add to the
playlist, and then press 1 or ENTER.
Repeat this step to add additional tracks to the playlist. You can
alternatively use the number buttons to select tracks.
3 Press ENTER or 1. The memory playback starts.
MEMORY indicator
27 En
In memory playback, you can create a playlist of up to 25 files.
Memory playback can be set only when the playback is stopped.
To Change the Display While the memory setting operations, press
DISPLAY to change the display information as follows: File name →
Folder name → Folder number/File number
Note
• See “Selecting Files (MP3/WMA)” for the Navigation Mode
information ( 23).
• The behavior of 2 on the compact disc player can be set from
“STOP KEY” ( 32).
• Memory playback is cancelled when you press 0 to open the disc
tray.
• Memory playback is cancelled when you press 8 or ON/STANDBY to
turn off the compact disc player.
Memory Playback (MP3/WMA)
76
MEMORY
DISPLAY
1 Press MEMORY. The MEMORY indicator lights.
2 Press " or 2. The compact disc player enters Navigation mode and
“[ROOT]” appears on the display.
3 Press " or ENTER (front panel: 1). The first folder name in ROOT
appears on the display.
4 Use #/$ or 7/6 to select other folders and files at the same
level. Folders that don’t contain files or subfolders can’t be
selected.
5 Press ENTER or " to move down a level (front panel: 1).
6 Use #/$ or 7/6 to select a file in the folder.
7 Press 1. The first file is memorized in the playlist.
8 Use #/$ or 7/6 to continue selecting the memory file.
To move up a level, press ! or 3 (front panel: 2). To continue
selecting the memory file, repeat steps 4 to 7. To memorize other
files of the same folder in the playlist, use 7/6 to select files,
then press 1.
9 Press ENTER or 1. Memory playback starts.
28 En
Note
• See “Selecting Files (MP3/WMA)” for the All Folder Mode
information ( 24).
• The behavior of 2 on the compact disc player can be set from
“STOP KEY” ( 32).
• Memory playback is cancelled when you press 0 to open the disc
tray.
• Memory playback is cancelled when you press 8 or ON/STANDBY to
turn off the compact disc player.
Memory Playback in All Folder Mode
1 Press MEMORY. The MEMORY indicator lights.
2 Press ! or 3 (front panel: press and hold 2). The compact disc
player enters All Folder mode and “1-” appears on the
display.
3 Use #/$ or 7/6 to select the folders.
76
MEMORY
5 Use #/$ or 7/6 to select the files.
6 Press 1 to memorized the first file.
7 Press 3 (front panel: 2), then repeat steps 3 to 6. To memorize
other files of the same folder in the playlist, repeat steps 5 to
6.
8 Press ENTER (front panel: 1). Memory playback starts.
29 En
In random playback, all of the files on the disc are played in
random order. This mode can only be used while playback is
stopped.
If you press RANDOM during playback, the message “NOR PLY” (Normal
play) is displayed.
Tip
• Random playback is cancelled when you press 0 to open the disc
tray.
• Random playback is cancelled when you press 8 or ON/STANDBY to
turn off the compact disc player.
Random Playback
1 While playback is stopped, press RANDOM. The RANDOM indicator
lights.
2 Press 1. The random playback starts.
3 To cancel random playback, stop the playback, then press RANDOM
to change the playback mode. The RANDOM indicator goes off, and
random playback is cancelled.
RANDOM
1
This section explains how to select MP3/WMA folders during
Playback.
Note
• SEARCH cannot be used during Random Playback and Memory Playback
( 26, 29).
• See “Selecting Files in All Folder Mode” to select folder by
number( 24).
Selecting a Folder (Search Mode)
1 During playback, press SEARCH. The compact disc player enters All
Folder mode and folders are displayed.
2 To select the previous folder, press 7. To select the next
folder, press 6. You can also use the number buttons to select the
folder.
3 Press ENTER or 1. Playback will start from the first file in the
selected folder.
ENTER
SEARCH
7, 6
30 En
(Audio CD Display) Track and total playing time appears on the
display.
(MP3/WMA Display) The name of disc appears on the display.
(Audio CD Display)
Elapsed file time: The length of time that the current file has
been playing (default display).
Remaining file time: The amount of time remaining for the current
file (REMAIN indicator appears).
Remaining disc time: The amount of time remaining for the entire
disc (TOTAL and REMAIN indicators appear).
(MP3/WMA Display) You can display various information about the
MP3/WMA file currently playing, including ID3 tags such as title
name, artist name, and album name.
Elapsed file time: The length of time that the current file has
been playing (default display).
File name: Name of the current file.
Folder name: Name of the current folder.
Title name: Title of the current file (if ID3 tag present). When
there is no ID3 tag, the message “TITLE-NO DATA” appears.
Artist name: Name of the Artist (if ID3 tag present).
Album name: Name of the album (if ID3 tag present).
Sampling rate and bit rate: Sampling rate and bit rate of the
current file.
Note
• To display the disc name, press DISPLAY while playback is
stopped.
• If a file or folder name contains any characters that cannot be
displayed, an underscore will appears in place of those characters.
Alternatively, you can set the compact disc player so that names
containing such characters are displayed as “FILE n” or “FOLDER n”,
“n” being the file or folder number. See “BAD- NAME” for
undisplayable characters setting ( 31).
Displaying Disc Information
1 Press DISPLAY repeatedly to show the following disc
information.
While playback is stopped
Setup Procedures
1 Press SETUP.
2 Use #/$ or 7/6 to select the preference you want to change.
The preferences are explained in the next column.
3 Press ENTER or 1.
4 Use #/$ or 7/6 to select the preference’s options.
5 Press ENTER or 1. When the preference has been set, “FINISH”
appears on the display.
7, 1, 6
FILTER SHARP (default)
This preference allows the band property up to 20 kHz to be output
almost flat.
SLOW This preference brings higher reproducibility of input
waveform, and is suitable to reproduce agogics, or subtle attack of
sound signals, along with sound image localization for each musical
instrument.
This preference configures the setting to switch the
characteristics of the digital filter for D/A conversion. You can
opt for whichever of the characteristics that vary depending on
your switching.
PHASE NORMAL (default)
The waveform recorded in disc will be output with its polarity left
intact.
REVERSE The waveform recorded in disc will be output with its
reversed polarity.
This preference configures the setting to switch the phase of the
analog audio output. You may give it a try to switch and listen so
that an optimum sound quality can be obtained from the amplifier
and the speakers on line.
DISC DISPLAY (default) NOT
This preference determines whether or not the disc name is
displayed when an MP3/WMA CD is read.
FILE SCROLL (default) NOT
This preference determines whether or not the file name scrolls
across the display when an MP3/WMA file is selected. In Navigation
mode, the file name scrolls across the display regardless of this
setting ( 23).
FOLDER SCROLL (default) NOT
This preference determines whether or not the folder name scrolls
across the display when an MP3/WMA folder is selected. In
Navigation mode, the folder name scrolls across the display
regardless of this setting ( 23).
HIDE-NUM DISABLE (default)
Displays numbers. ENABLE
Hides numbers. This preference determines whether or not the
numbers at the beginning of file and folder names are hidden. When
you create an MP3/WMA CD on a personal computer, you cannot
normally determine the playback order of the files. However, if you
number the MP3/WMA files in order, starting with 01, 02, 03, and so
on, they will play in that order.
BAD-NAME NOT (default) REPLACE
This preference determines whether or not file and folder names
that contain undisplayable characters are replaced with “FILE n.”
or “FOLDER n.”, “n” being the file or folder number. When set to
“NOT”, displayable characters are displayed and underscores are
used in place of any undisplayable characters. For ID3 tags,
underscores are used in place of undisplayable characters
regardless of this preference.
Preferences
AUDIO
DISPLAY
ID3-VER1 READ (default) NO READ
This preference determines whether or not version 1.0/1.1 tags are
read and displayed. When set to “NO READ”, version 1.0/1.1 ID3 tags
will not be displayed.
ID3-VER2 READ (default) NO READ
This preference determines whether or not version 2.2/2.3/2.4 tags
are read and displayed. When set to “NO READ”, version 2.2/2.3/2.4
ID3 tags will not be displayed.
CD-EXTRA AUDIO (default) MP3
This preference applies to CD Extra discs and determines whether
music in the audio session or MP3/WMA files in the data session are
played.
JOLIET USE SVD (default) ISO9660
This preference applies to MP3/WMA CDs in Joliet format and
determines whether the compact disc player reads the SVD data or
treats the disc as an ISO 9660 disc. Normally, this preference
doesn’t need to be changed. SVD (Supplementary Volume Descriptor)
supports long file and folder names and characters other than
letters and numbers.
STOP-KEY NAVI (default) FOLDER DISABLE
This preference determines how 2 on the compact disc player works.
When the “NAVI” (Navigation) option is selected, pressing 2 once
selects Navigation mode. When the “FOLDER” (ALL Folder) option is
selected, pressing 2 once selects All Folder mode. When the
“DISABLE” option is selected, compact disc player does not enter
Navigation or All Folder mode by pressing 2.
Note
ASb (Auto Standby) ON OFF
For compact disc player playback, it is activated when the playback
is stopped for 30 minutes; however, it is not activated when the
playback is paused continuously. Default setting: ON (European
models), OFF (North American models)
Note
• Before entering standby mode with the ASb function, the Display
Off LED flashes 30 seconds before the ASb function starts
running.
INITIAL CANCEL EXECUTE
This preference resets the compact disc player to factory
default.
Switch the output between DIGITAL/ANALOG, DIGITAL, ANALOG in
order.
EXTRA
Setting the Analog/Digital Output
1 Press OUTPUT MODE repeatedly on the front panel. The selected
Audio output indicator lights.
DIGITAL/ANALOG (default): Uses both outputs.
DIGITAL: Uses the digital output only. Turn the analog output off
to perform more stable playback.
ANALOG: Uses the analog output only. Turn the digital output off to
reduce the effect of digital noise during playback.
OUTPUT MODE
Others
Troubleshooting
• Make sure that the power cord is properly plugged into the wall
outlet ( 18).
• Unplug the power cord from the wall outlet, wait 5 seconds or
more, then plug it in again.
• When the set ASb starts running, the compact disc player will
automatically go Standby ( 32).
Power
The Compact Disc Player turns off unexpectedly.
• Check all connections and correct as necessary ( 17). • Make sure
that there is no unsupported file formats or
signals. • The compact disc player is equipped with a feature
to
switch the digital/analog output. Check if the connection between
the compact disc player and a connected component is appropriate,
and also whether the selection of the selector is correct.
• Make sure all audio connecting plugs are pushed in all the way (
17).
• The sound quality can be affected by strong magnetic fields, such
as that from a TV. Try moving any such devices away from the
compact disc player.
• If you have any devices that emit high-intensity radio waves near
the compact disc player, such as a cellular phone that’s being used
to make a call, the compact disc player may output noise.
• The compact disc player’s precision drive mechanism may emit a
faint hissing sound while reading discs during playback or when
searching for tracks. You may be able to hear this noise in
extremely quiet environments.
• The compact disc player is not a portable device. Use it in a
location that’s not subject to shock or vibration.
• Audio performance will be at its best about 10 to 30 minutes
after the compact disc player has been turned on and had time to
warm up.
• Using cable ties to bundle audio cables with speaker or power
cables may degrade the sound quality. So don’t do it.
Audio
The sound quality is not good.
Audio output is intermittent when the Compact Disc Player is
subjected to vibration.
Audio performance
34 En
• The disc is upside down. Load the disc with the label- side
facing up ( 15, 22).
• The disc is dirty. Remove the disc and clean it ( 15). • If
condensation appears, unplug the power cord and
leave the compact disc player more than 3 hours at room
temperature.
• Make sure the disc is standard. See “Disc Note” ( 15). •
CD-R/CD-RW that are not finalized cannot be played.
• Install the compact disc player somewhere free of
vibration.
• The disc is dirty. Remove the disc and clean it ( 15). • The disc
is very scratched. Replace the disc.
• No such track on the disc. Enter another number ( 24).
• The disc is dirty. Remove the disc and clean it ( 15). • The disc
is very scratched. Replace the disc.
• Turn off any special playback modes (e.g. repeat, memory, or
random).
• Make sure the audio cable is connected correctly ( 17).
• Make sure that all audio connecting plugs are pushed in all the
way ( 17).
• Make sure that the connected component’s input jack and the input
settings are correct.
• Make sure that the connected component’s volume isn’t set to the
lowest level, and that the volume isn’t muted.
• The disc is either scratched or dirty, and disc information
cannot be properly read.
• Make sure that the disc is not scratched or dirty. • Due to a
scratched or dirty disc, playback may not
operate normally or the sound may be jumpy.
• Make sure the batteries have been installed with the correct
polarity (+/–) ( 10).
• Replace both batteries with new ones. (Do not mix different types
of batteries or new and old batteries.)
• The remote controller is too far away from the compact disc
player, or there’s an obstacle between them ( 10).
• The compact disc player’s remote control sensor is being
subjected to bright light (inverter-type fluorescent light or
sunlight).
• The compact disc player is located behind the glass doors of a
audio rack or cabinet.
Disc Playback
Disc playback skips.
It takes a long time to locate certain tracks.
Can not play tracks in the disc’s playback order.
External Components
Display Unit
The remote controller doesn’t work properly.
Onkyo is not responsible for damages (such as CD rental fees) due
to unsuccessful recordings caused by the unit’s malfunction. Before
you record important data, make sure that the material will be
recorded correctly.
The compact disc player contains a microcomputer for signal
processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity
may cause it to lockup. In the unlikely event that this should
happen, unplug the power cord, wait at least 5 seconds, and then
plug it again.
Before disconnecting the power cord from the wall outlet, set the
main power switch to OFF.
35 En
C-7000R
Audio Dynamic Range 100 dB
THD (Total Harmonic Distortion) 0.0015 %
Audio Output/Impedance Optical Coaxial AES/EBU
–22.5 dBm 0.5 Vp-p / 75 3.3 Vp-p / 110
Rated RCA Output Level and Impedance 2.0 V (rms) / 330 Digital
Outputs Optical: 1
Coaxial: 1
Balance Output AES/EBU (DIGITAL)
Power Supply (North American) AC 120 V, 60 Hz (European) AC 230 V,
50 Hz
Power Consumption (North American) 21 W (European) 18 W
Standby Power Consumption (North American) 0.2 W (European) 0.3
W
Dimensions (W × H × D) 435 W × 99 H × 315.2 D mm (17-1/8 W × 3-7/8
H × 12-7/16 D inches)
Weight 12 kg (26.5 lbs)
Operation Condition Temperature/Humidity 5 ºC - 35 ºC/15% -
85%
Playable Discs Audio CD, CD-R, CD-RW, MP3, WMA (CD-R, CD-RW) *
Discs that have not been properly finalized may only be
partially playable or not playable at all.
SN 29400529A
Y1102-2
(C) Copyright 2011 ONKYO SOUND & VISION CORPORATION Japan. All
rights reserved. * 2 9 4 0 0 5 2 9 A *
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel:
072-831-8023 Fax: 072-831-8163 http://www.onkyo.com/
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel:
800-229-1687, 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel:
+49-8142-4401-0 Fax: +49-8142-4401-555
http://www.eu.onkyo.com/
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB,
UK Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port
Road, Kwai Chung, N.T., Hong Kong. Tel: 852-2429-3118 Fax:
852-2428-9039 http://www.ch.onkyo.com/
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China
200041, Tel: 86-21-52131366 Fax: 86-21-52130396
Installing the Batteries
Getting to Know the Compact Disc Player
Front Panel
Turning On & Basic Operations
Playing the Disc
Selecting Files (MP3/WMA)
Displaying Disc Information