Post on 05-Feb-2018
Brush Holders
Schunk Graphite Technology
Table of Contents
2
8 – 10 Clamping Brush Holders
11 – 20 Box Brush Holders
21 – 25 Tandem Brush Holders
26 – 28 Top & Rocker Rings
29 – 35 Appendix
3 – 7 Leg Brush Holders
Brush - dimensions Holder - dimensions
Brush-Article no. t a r d ** q u M pressure *
06.09.2009.10 6.4 6.4 12.5 10 9.5 44 4 18006.09.2106.07 8 5 12.5 7 8 30 3 50006.09.2108.08 10 5 12.5 8 8 35 3 18006.09.2010.10 12.5 6.3 20 10 9.5 40 4 25006.09.2055.13 16 8 16 13 12 50 4 25006.09.2059.13 16 8 16 13 12 62 4 18006.09.0485... 16 8 20 6-13 12 46 6 20006.09.0486... 16 8 20 6-16 12 60 6 20006.09.0622... 16 8 20 6-13 12 50 6 20006.09.2088.10 20 8 20 10 12 50 6 20006.09.2088.60 20 8 20 13 12 50 5 20006.09.0488... 20 8 25 6-16 12 60 6 20006.09.0489... 20 8 25 6-16 12 70 6 20006.09.0638... 20 8 25 6-13 12 50 6 20006.09.0490... 20 10 25 6-16 14.5 60 6 20006.09.0491... 20 10 25 6-16 14.5 70 6 20006.09.0492... 20 10 25 6-16 14.5 80 6 20006.09.0496... 25 10 25 6-16 14.5 55 6 20006.09.0497... 25 10 25 6-16 14.5 65 6 20006.09.2103... 25 10 25 6-16 14.5 80 6 20006.09.0499... 25 12.5 25 6-16 18 75 6 200
Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request
Design subject to change
One-piece clamp
3
Single Leg Brush Holders
4
Single Leg Brush Holders
Brush - dimensions Holder - dimensions
Brush- AdditionalArticle no. t a r d ** q u M pressure * connector
06.09.0500... 20 10 25 16-20 14.5 70 6 20006.09.0501... 20 10 25 16-20 14.5 80 6 20006.09.0502... 25 10 25 16-20 14.5 75 6 20006.09.0503... 25 10 25 16-20 14.5 85 6 20006.09.0504... 25 12.5 25 16-20 18 75 8 20006.09.0505... 25 12.5 25 16-20 18 85 8 20006.09.0506... 32 12.5 32 16-20 18 80 8 20006.09.0509... 32 16 32 16-20 21 90 8 20006.09.0510... 32 16 32 16-20 21 100 8 20006.09.0666.25 32 16 32 25 24 110 8 22506.09.0681.20 32 16 32 20 21 80 8 20006.09.0514... 40 16 40 16-20 21 90 8 20006.09.0515... 40 16 40 16-20 21 120 8 20006.09.0516.25 40 20 40 25 26 115 10 20006.09.0517.25 40 20 40 25 26 125 10 20006.09.0640.25 40 20 40 25 26 108 10 20006.09.0680.25 40 20 40 25 26 108 10 20006.09.2086.25 50 25 40 25 33 135 10 18006.09.2097.13 20 8 20 13 12 100 6 200 x06.09.2101.16 25 10 25 16 14 80 6 200 x06.09.0028... 25 12 25 12-22 19 94 6 225 x06.09.0571.16 25 12.5 25 16 18 70 5 200 x06.09.2048.16 25 16 32 16 24 85 6 200 x06.09.2100.20 32 12.5 32 20 17.5 100 8 200 x06.09.0036... 32 16 32 13-25 24 110 8 225 x06.09.2049.20 32 16 40 20 24 110 8 250 x06.09.0038... 40 16 40 13-25 24 106 8 225 x06.09.0045... 40 20 40 13-25 28 110 8 225 x06.09.0046... 40 20 40 13-25 28 125 8 225 x06.09.0047... 40 20 40 13-25 28 150 8 225 x06.09.0110... 40 20 40 13-25 28 110 8 225 x06.09.0589... 40 20 40 13-25 28 110 8 225 x06.09.2050.25 40 20 40 25 28 110 8 300 x06.09.2052.25 40 20 40 25 28 150 8 200 x06.09.0051... 40 25 40 13-25 33 165 8 225 x06.09.0695.25 50 25 40 25 33 145 8 200 x06.09.2068.25 50 25 40 25 33 145 8 200 x
Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request
Design subject to change
With hinge clamp Hinge clamp with additional connector
Brush - dimensions Holder - dimensions Form design
Brush- WithArticle no. t a r d ** q u M pressure * brush A B C
06.09.4004.08 8 5 16 8 9 35 4 400 x06.09.4004.10 8 5 16 10 9 35 4 180 x06.09.4006... 10 5 12.5 8/10 9 35 4 300 x06.09.4006.09 10 5 12.5 9 9 35 3 400 x06.09.0435.12 10 5 15 12 9 40 4 250 x06.09.4135.09 10 6.4 16 9 10 43 5 550 x x06.09.4099.13 12.5 6.4 20 13 10 47 5 250 x x06.09.4019... 12.5 8 16 10-13 12 40 6 180 x06.09.4384.10 15 6 20 10 10 42 4 800 x x06.09.4383.10 16 6.4 16 10 10 42 4 180 x06.09.4023.10 16 8 20 10 12 45 6 200 x06.09.4028.16 16 8 20 16 12 55 6 200 x06.09.4111.50 16 8 20 12.5 12 46 6 300 x x06.09.4349.13 16 8 20 13 12 46 6 200 x06.09.4392.13 16 8 20 13 12 50 5 200 x06.09.4404.13 16 8 20 13 12 55 6 800 x06.09.4155.13 16 8 20 13 12 50 6 350 x06.09.4160.13 16 8 20 13 12 64 6 275 x x06.09.4160.16 16 8 20 16 12 64 6 275 x06.09.4339.13 16 10 25 13 14 65 6 250 x x06.09.4388.13 20 8 20 13 12 50 6 200 x06.09.4161... 20 8 25 8-13 12 50 6 200 x06.09.4352... 20 10 20 13-16 14 75 6 180 x06.09.4115.13 20 10 25 13 14 70 8 250 x x06.09.4189.13 20 12.5 25 13 17 65 8 200 x06.09.4167.10 25 8 25 10 12 60 6 200 x06.09.4119.13 25 10 25 13 12 70 8 180 x x06.09.4355.13 25 10 25 13 12 70 8 180 x06.09.4199... 32 12.5 32 16-20 17 80 8 200 x
Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request
Design subject to change
Form A Form B Form C
5
Double Leg Brush Holders
6
Double Leg Brush Holders
Brush - dimensions Holder - dimensions
Brush- One HingeArticle no. t a r d ** q u M pressure * piece clamp
06.09.0346... 12.5 8 20 6-13 12 48 6 250 x06.09.0347... 16 8 20 6-13 12 46 6 200 x06.09.0623... 16 8 20 6-13 12 50 6 200 x06.09.0348... 16 8 20 6-16 12 60 6 200 x06.09.0350... 16 10 25 6-16 14.5 50 6 200 x06.09.0352... 20 8 25 6-13 12 50 6 200 x06.09.0353... 20 8 25 6-16 12 60 6 200 x06.09.0354... 20 8 25 6-16 12 70 6 200 x06.09.0356... 20 10 25 6-16 14.5 60 6 200 x06.09.0357... 20 10 25 6-16 14.5 70 6 200 x06.09.0358... 20 10 25 6-16 14.5 80 6 200 x06.09.0361... 20 12.5 25 6-16 18 60 6 200 x06.09.0362... 20 12.5 25 6-16 18 75 6 200 x06.09.0363... 25 8 25 6-16 12 55 6 200 x06.09.0365... 25 10 25 6-16 14.5 55 6 200 x06.09.0366... 25 10 25 6-16 14.5 65 6 200 x06.09.0368... 25 10 25 6-16 14.5 75 6 200 x06.09.0374... 20 10 25 16-20 14.5 70 6 200 x06.09.0376... 25 10 25 16-20 14.5 75 6 200 x06.09.0377... 25 10 25 16-20 14.5 85 6 200 x06.09.0378... 25 12.5 25 16-20 18 75 8 200 x06.09.0379... 25 12.5 25 16-20 18 85 8 200 x06.09.0380... 25 12.5 25 16-20 18 95 8 200 x06.09.0382... 32 12.5 32 16-20 18 80 8 200 x06.09.0385... 32 16 32 16-20 21 90 8 200 x06.09.0386... 32 16 32 16-20 21 100 8 200 x06.09.0388... 32 16 32 16-20 21 120 8 200 x06.09.0389.25 32 20 32 25 26 110 10 200 x06.09.0641.25 40 20 40 25 26 125 10 200 x
Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request
Design subject to change
One piece clamp Hinge Clamp
7
Double Leg Brush Holders
Brush - dimensions Holder - dimensions Form design
Brush- WithArticle no. t a r d ** q u M pressure * brush A B
06.09.4320.13 16 6.3 12 13 12 46 4 375 x x06.09.0700.10 22 6.4 13.5 10 12.5 46 4 250 x x06.09.0701.08 22 6.4 13.5 8 12.5 46 4 250 x x06.09.4301.16 25 8 20 16 17 60 6 275 x06.09.4321... 25 8 20 13-16 16 60 6 250 x x06.09.4303.16 32 10 20 16 17 64 8 375 x x06.09.4323.20 32 10 20 20 17 64 8 200 x
Dimensions in mm* cN/cm2 - Specific brush pressureFurther dimensions on request
Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressure
Design subject to change
Design subject to change
Form A Form B
Phase Version Grounding Version
Double leg brush-holders with carbon hinge
Contact arrangement
Brush - dimensions Holder - dimensions
Brush-Article no. t a r d ** q u M pressure *
06.09.2009.10 6.4 6.4 12.5 10 9.5 44 4 18006.09.2106.07 8 5 12.5 7 8 30 3 500
8
Double Clamping Brush Holders
Brush - dimensions Holder Dimensions
StandardArticle no. *9 t a r c e h l q u v w x z M1 M2 M3
DRDS 06.03.3056... 25 10 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDS1 06.03.3100... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS2 06.03.3130... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS 06.03.3057... 25 12.5 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDS1 06.03.3101... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS2 06.03.3131... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS 06.03.3058... 32 12.5 40 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6DRDS1 06.03.3102... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDS2 06.03.3122... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDS 06.03.3065... 32 16 40 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8DRDS1 06.03.3103... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDS2 06.03.3123... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDS 06.03.3066... 32 20 40 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8DRDS1 06.03.3104... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDS2 06.03.3124... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDS 06.03.3069... 40 20 50 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8DRDS1 06.03.3107... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDS2 06.03.3127... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDS 06.03.3070... 40 25 50 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8DRDS1 06.03.3108... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDS2 06.03.3128... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDS 06.03.3071... 40 32 50 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8DRDS1 06.03.3109... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10DRDS2 06.03.3129... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10
Dimensions in mm*d = complete dimension "d" in part number* cN/cm2 - Specific brush pressureFurther dimensions on request
Type DRDS, DRDS1, DRDS2
Design subject to change
DRDS
DRDS1
DRDS2
9
Type DRDF, DRDF1, DRDF2
DRDF
DRDF1
DRDF2
Double Clamping Brush Holders
Brush - dimensions Holder Dimensions
StandardArticle no. *9 t a r c e h l q u v w x z M1 M2 M3
DRDF 06.03.4056... 25 10 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDF1 06.03.4100... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF2 06.03.4130... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF 06.03.4057... 25 12.5 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDF1 06.03.4101... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF2 06.03.4131... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF 06.03.4058... 32 12.5 40 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6DRDF1 06.03.4102... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDF2 06.03.4122... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDF 06.03.4065... 32 16 40 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8DRDF1 06.03.4103... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDF2 06.03.4123... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDF 06.03.4066... 32 20 40 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8DRDF1 06.03.4104... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDF2 06.03.4124... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDF 06.03.4069... 40 20 50 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8DRDF1 06.03.4107... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDF2 06.03.4127... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDF 06.03.4070... 40 25 50 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8DRDF1 06.03.4108... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDF2 06.03.4128... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDF 06.03.4071... 40 32 50 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8DRDF1 06.03.4109... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10DRDF2 06.03.4129... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10
Dimensions in mm*d = complete dimension "d" in part number* cN/cm2 - Specific brush pressureFurther dimensions on request
Design subject to change
10
Double Clamping Brush Holders
Slip Ring Diameter
Brush Holder 90 100 125 160 200 250 315 400 500DRDF 2510 35 34 33 32.5 32 31.5 31.5 31DRDS 2512 35 34 33 32.5 32 31.5 31.5 31
3212 40 39 38 37.5 36.5 36 36 35.53216 44.5 43.5 43 42 41.5 41 40.53220 44.5 43.5 43 42 41.5 41 40.53225 44.5 43.5 43 42 41.5 41 40.54020 49 48 47 46.5 45.5 454025 49 48 47 46.5 45.5 454032 49 48 47 46.5 45.5 45
DRDF1 2510 35 34 33 32.5 32 31.5 31.5 31DRDF2 2512 35 34 33 32.5 32 31.5 31.5 31DRDS1 3212 40 39 38 37.5 36.5 36 36 35.5DRDS2 3216 44.5 43.5 43 42 41.5 41 40.5
3220 44.5 43.5 43 42 41.5 41 40.53225 44.5 43.5 43 42 41.5 41 40.54020 45.5 44.5 43.5 42.5 42 41.54025 45.5 44.5 43.5 42.5 42 41.54032 45.5 44.5 43.5 42.5 42 41.5
Dimensions in mmDimensions rounded in 0.5 mm incrementsFurther dimensions on request
Slip Ring Measurements
Design subject to change
11
Single Brush Holders
Type BRD
Made of die cast brass with extension spring and spark protection
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e k m q v z pBRD - 1025 06.04.2108.02 10 25 40 15 37 25 6.4 10.2 29 5.5 58 200BRD - 1225 06.04.2109.01 12.5 25 40 16.3 38 25 6.4 10.2 29 5.5 59 200BRD - 1625 06.04.2110.00 16 25 40 18 40 25 6.4 10.2 29 5.5 61 200BRD - 2025 06.04.2116.02 20 25 40 20 42 25 6.4 10.2 29 5.5 63 200BRD - 1032 06.04.2111.01 10 32 40 15.5 37 25 6.4 10.2 36 5.5 58 200BRD - 1232 06.04.2112.00 12.5 32 40 16.8 38 25 6.4 10.2 36 5.5 59 200BRD - 1632 06.04.2113.00 16 32 40 18.5 40 25 6.4 10.2 36 5.5 61 200BRD - 2032 06.04.2114.00 20 32 40 20.5 42 25 6.4 10.2 36 5.5 63 200BRD - 2532 06.04.2115.00 25 32 40 23 44.5 25 6.4 10.2 36 5.5 65.5 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
12
Type BRS
Made from sheet brass with extension spring and spark protection
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e/I k m q v z pBRS - 1025 06.04.2349.00 10 25 40 15 37 25 6.4 10.2 29 4.5 46 200BRS - 1225 06.04.2350.00 12.5 25 40 16.3 38.25 25 6.4 10.2 29 4.5 46 200BRS - 1625 06.04.2351.00 16 25 40 18 40 25 6.4 10.2 29 4.5 46 200BRS - 2025 06.04.2352.00 20 25 40 20 42 25 6.4 10.2 29 4.5 46 200BRS - 1032 06.04.2353.00 10 32 50 15.5 41.5 30 8.4 14.2 36 4.5 51 200BRS - 1232 06.04.2354.00 12.5 32 50 16.8 42.75 30 8.4 14.2 36 4.5 51 200BRS - 1632 06.04.2355.00 16 32 50 18.5 44.5 30 8.4 14.2 36 4.5 52 200BRS - 2032 06.04.2356.00 20 32 50 20.5 46.5 30 8.4 14.2 36 4.5 54 200BRS - 2532 06.04.2357.00 25 32 50 23 49 30 8.4 14.2 36 4.5 56 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
Single Brush Holders
13
Type BRM
Made of die cast brass with extension spring and spark protection
Single Brush Holders
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e g I k m q v pBRM - 1032 06.04.2329.00 10 32 50 15.5 63 64 40 32 8.5 14.5 37 6 200BRM - 1232 06.04.3089.00 12.5 32 50 16.8 63 64 40 32 8.5 14.5 37 6 200BRM - 1632 06.04.2327.02 16 32 50 18.5 64 64 40 32 8.5 14.5 37 6 200BRM - 2032 06.04.3058.00 20 32 50 28 76 88 43 32 8.5 14.5 37 12.5 200BRM - 2032 06.04.2258.00 20 32 50 26 76 88 43 32 8.5 16.5 37 10.5 200BRM - 2032 06.04.2258.22 20 32 50 20.5 76 88 43 32 8.5 14.5 37 6 200BRM - 2532 06.04.2261.00 25 32 50 26 76 88 43 32 8.5 16.5 37 8 200BRM - 2532 06.04.2261.19 25 32 50 23 76 88 43 32 8.5 14.5 37 6 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
14
Type BRG + BRH
Made of die cast brass with extension spring
Single Brush Holders
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e I k m n q v w pBRG1 - 1025 06.04.2175.00 10 25 50 15 59 84 32 6.4 10.2 20 29.5 5 7 180BRG1 - 1225 06.04.2176.00 12.5 25 50 16.3 60 84 32 6.4 10.2 20 29.5 5 7 180BRG1 - 1625 06.04.2177.00 16 25 50 18 62 84 32 6.4 10.2 20 29.5 5 9 180BRG1 - 1232 06.04.2181.00 12.5 32 64 16.8 76 100 40 8.4 14.2 25 37 6 7 180BRG1 - 1632 06.04.2182.04 16 32 64 18.5 78 100 40 8.4 14.2 25 37 6 9 200BRG1 - 2032 06.04.2184.04 20 32 64 20.5 80 100 40 8.4 14.2 25 37 6 12 200BRG1 - 2532 06.04.2186.00 25 32 64 23 82 100 40 8.4 14.2 25 37 6 12 180BRG1 - 3232 06.04.2188.00 32 32 64 26.5 86 100 40 8.4 14.2 25 37 6 12 180BRG3 - 4032 06.04.2194.00 40 32 64 32 90 100 40 8.4 16.1 25 37 6.5 14 180
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
15
Type ARB1, ARB4, ARB6*
Made from brass sheet with clock spring and spark protection
Single Brush Holders
Spark Protection
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e I k m q v z pARB1 - 0812 06.04.0028.00 8 12.5 25 14 21 16 20 5.4 9.2 17.5 7 29 180ARB1 - 1012 06.04.0029.00 10 12.5 25 15 22 16 20 5.4 9.2 17.5 7 29 180ARB1 - 0816 06.04.0030.00 8 16 25 14 24 16 20 6.4 10.2 21 7 34 180ARB1 - 1016 06.04.0031.00 10 16 25 15 25 16 20 6.4 10.2 21 7 34 180ARB1 - 1216 06.04.0032.00 12.5 16 25 16.3 26.5 16 20 6.4 10.2 21 7 34 180ARB6 - 0820 06.04.0033.00 8 20 25 14 24 16 20 6.4 10.2 25 7 34 180ARB6 - 1020 06.04.0034.00 10 20 25 15 25 16 20 6.4 10.2 25 7 34 180ARB6 - 1220 06.04.0035.00 12.5 20 25 16.3 26.5 16 20 6.4 10.2 25 7 34 180ARB6 - 1620 06.04.0036.00 16 20 25 18 28 16 20 6.4 10.2 25 7 34 180ARB6 - 1025 06.04.0037.00 10 25 32 15 30.5 20 25 6.4 10.2 30 7 42 180ARB6 - 1225 06.04.0038.00 12.5 25 32 16.3 31.8 20 25 6.4 10.2 30 7 42 180ARB6 - 1625 06.04.0039.00 16 25 32 18 33.5 20 25 6.4 10.2 30 7 42 180ARB6 - 2025 06.04.0040.01 20 25 32 20 35.5 20 25 6.4 10.2 30 7 42 250ARB4 - 1632 06.04.0024.00 16 32 40 18.5 37.5 25 25 8.4 14.2 38 6.5 42 180ARB4 - 2532 06.04.0044.00 25 32 40 23 42 25 25 8.4 14.2 38 6.5 47 180
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
ARB1 without spark arrestorARB4 with raised clamping faceARB6 with spark arrestor
*
Design subject to change
Single Brush Holders
Type BRB1
Made of sheet brass with extension spring
16
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e I k m q v z pBRB1 - 2010 06.04.2296.00 20 10 32 20 33.5 22 20 6.4 10.2 13 5.5 37 200BRB1 - 2512 06.04.2297.00 25 12.5 32 22.5 36 22 22 6.4 10.2 15.5 5.5 38 200BRB1 - 2516 06.04.2298.01 25 16 32 22.5 36 22 22 6.4 10.2 19 5.5 38 200BRB1 - 3216 06.04.2299.00 32 16 40 26.5 42.5 26 26 8.4 14.2 20 5.5 48 200BRB1 - 3220 06.04.2300.00 32 20 40 26.5 42.5 26 26 8.4 14.2 24 5.5 48 200BRB1 - 4020 06.04.2301.00 40 20 40 30.5 46.5 28 28 8.4 14.2 24 5.5 50 200BRB1 - 4025 06.04.2302.00 40 25 40 30.5 46.5 28 28 8.4 14.2 29 5.5 50 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
Single Brush Holders
Type CRB
Brass Extrusion with Self Recoiling Spring
17
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e I k m q v pCRB - 1025 06.04.4088.01 10 25 50 15 17 63 40 6.4 10.2 29.5 5.5 200CRB - 1225 06.04.4089.01 12.5 25 50 16.3 18.3 63 40 6.4 10.2 29.5 5.5 200CRB - 1625 06.04.4090.02 16 25 50 18 20 67 40 6.4 10.2 29.5 5.5 200CRB - 2025 06.04.4091.02 20 25 50 20 22 70 40 6.4 10.2 29.5 5.5 200CRB - 3030 06.04.4173.00 30 30 64 25.5 27 88 50 6.4 14.2 34.5 6 200CRB - 1032 06.04.4092.02 10 32 64 15.5 17 77 50 6.4 10.2 36.5 6 200CRB - 1232 06.04.4093.02 12.5 32 64 16.8 18.5 77 50 6.4 10.2 36.5 6 200CRB - 1632 06.04.4094.03 16 32 64 18.5 20 81 50 6.4 10.2 36.5 6 200CRB - 2032 06.04.4095.05 20 32 64 20.5 22 84 50 6.4 10.2 36.5 6 200CRB - 2532 06.04.4096.27 25 32 64 23 24.5 88 50 6.4 10.2 36.5 6 200
Design subject to change
Single Brush Holders
Type CRA
Brass Die Casting with Self Recoiling Spring
18
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e k m I q v pCRA - 0616 06.04.4030.03 6.4 16 40 14 14.5 38 6.4 10.2 26 20 5.5 250CRA - 0818 06.04.4031.03 8 16 40 14 14.5 38 6.4 10.2 26 20 5.5 200CRA - 1016 06.04.4032.11 10 16 40 15 15.5 38 6.4 10.2 26 20 5.5 200CRA - 1216 06.04.4033.01 12.5 16 40 16.3 16.8 38 6.4 10.2 26 20 5.5 200CRA - 0820 06.04.4034.01 8 20 40 14 14.5 38 6.4 10.2 26 24 5.5 200CRA - 1020 06.04.4035.05 10 20 40 15 15.5 38 6.4 10.2 26 24 5.5 200CRA - 1220 06.04.4036.01 12 20 40 16.3 16.8 38 6.4 10.2 26 24 5.5 200CRA - 1620 06.04.4037.01 16 20 40 18 18.5 38 6.4 10.2 26 24 5.5 200CRA - 1225 06.04.4198.02 12.5 25 50 16.25 20.75 50 5.5 10.2 35 29.5 5.5 200CRA - 1625 06.04.4181.01 16 25 50 17.5 22.5 58 6.4 10.2 35 29.5 5.5 160CRA - 1232 06.04.4163.01 12.5 32 64 16.8 23.25 60 8.5 14.2 40 36.5 6 200CRA - 1632 06.04.4164.01 16 32 64 18.5 25 60 8.5 14.2 40 36.5 6 200CRA - 2032 06.04.4165.01 20 32 64 20.5 27 60 8.5 14.2 40 36.5 6 200CRA - 2532 06.04.4166.01 25 32 64 23 29.5 60 8.5 14.2 40 36.5 6 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
Double Brush Holders
Type BRE
Made of die cast brass with extension spring and spark protection
19
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e I q z pBRE - 1012 06.04.2244.00 10 12.5 32 17 38.5 26 22 31.5 43 200BRE - 1612 06.04.2245.00 16 12.5 32 20 41.5 26 22 31.5 45 200BRE - 2012 06.04.2246.00 20 12.5 32 22 43.5 26 22 31.5 45 200BRE - 1216 06.04.2248.00 12.5 16 32 18 45 26 23 38.5 49 200BRE - 1616 06.04.2249.00 16 16 40 20 50 31 25 38.5 55 200BRE - 2016 06.04.2250.00 20 16 40 22 52 31 25 38.5 55 200BRE - 2516 06.04.2251.00 25 16 50 24.5 55 37 30 38.5 59 200BRE - 1620 06.04.2252.00 16 20 40 20 52 31 25 46.5 55 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
Triple Brush Holders
Type BRF
Made of Cast Bronze with extension spring and spark protection
20
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u c e I q z pBRF - 1012 06.04.2254.00 10 12.5 32 17 38.5 26 22 46 43 200BRF - 1612 06.04.2255.00 16 12.5 32 20 41.5 26 22 49 45 200BRF - 2012 06.04.2256.00 20 12.5 32 22 43.5 26 22 46.5 45 200BRF - 2516 06.04.2257.00 25 16 50 24.5 55 37 30 59 59 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
Design subject to change
Tandem Brush Holders
Type TRA, TRA2*
Made of brass die casting with extension spring and spark protection
21
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u v c e z pTRA2 - 1032 06.07.0098.02 10 32 50 28 10.5 65.7 33 63 200*TRA2 - 1232 06.07.0099.02 12.5 32 50 28 8 70.7 39.7 68 200*TRA2 - 1632 06.07.0100.02 16 32 50 32 8.5 89.2 42.5 86 200TRA - 2032 06.07.0101.00 20 32 50 36 8.5 93.9 40 86 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2
TRA is with cast brush fingersTRA2 is with stamped brush fingers*
Design subject to change
Tandem Brush Holders
Type TRB1, TRB2, TRB3, TRB4*
Made of brass die casting with extension spring and spark protection
22
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u v c e z pTRB3 - 0832 06.07.0193.00 8 32 50 28 12 63.5 35 73 350TRB3 - 1032 06.07.0061.03 10 32 50 28 9.5 63.5 35 73 200*TRB3 - 1232 06.07.0062.06 12.5 32 50 28 9.5 63.5 35 75 200*TRB3 - 1632 06.07.0063.05 16 32 50 28 6.5 63.5 35 76 200TRB1 - 2032 06.07.0064.06 20 32 50 28 6.5 63.5 35 80 200TRB4 - 1032 06.07.0049.02 10 32 50 28 9.5 63.5 35 73 250TRB4 - 1232 06.07.0050.03 12.5 32 50 28 9.5 63.5 35 75 250TRB4 - 1632 06.07.0051.02 16 32 50 28 6.5 63.5 35 76 200TRB2 - 2032 06.07.0052.00 20 32 50 32 6.5 63.5 35 80 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2
TRB1 is with die cast pressure fingers and serrated mounting faceTRB2 is with die cast pressure fingers and mounting cavityTRB3 is with stamped pressure fingers and serrated mounting faceTRB4 is with stamped pressure fingers and mounting cavity
*
Design subject to change
Tandem Brush Holders
Type TNA, TNA2* 7.5°
Made of brass die casting with extension spring and spark protection
23
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u v c e z pTNA2 - 1032 06.07.0102.03 10 32 50 28 6 60.8 40.7 64 200*TNA2 - 1232 06.07.0103.05 12.5 32 50 28 6 66.2 42 68 200*TNA2 - 1632 06.07.0104.02 16 32 50 32 6 85.5 44.7 86 200TNA - 2032 06.07.0105.00 20 32 50 28 6 87 44.9 87 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2
TNA is with die cast pressure fingers and serrated mounting faceTNA2 is with stamped pressure fingers and serrated mounting face*
Design subject to change
Tandem Brush Holders
Type TNC1, TNC2, TNC3, TNC4* 8°
Made of brass die casting with extension spring and spark protection
24
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u v c e z pTNC3 - 1032 06.07.0094.09 10 32 50 27 6.5 60.5 41 63 200*TNC3 - 1232 06.07.0095.12 12.5 32 50 29.5 6.5 65.8 42.7 68 200*TNC3 - 1632 06.07.0096.14 16 32 50 32 6.5 84.7 45.3 86 200TNC1 - 2032 06.07.0097.06 20 32 50 36 6.5 86.7 45.3 86 200TNC1 - 2532 06.07.0194.04 25 32 50 42 6.5 94 42 90 200TNC4 - 1032 06.07.0082.06 10 32 50 27 6.5 60.5 41 63 250TNC4 - 1232 06.07.0083.06 12.5 32 50 29.5 6.5 65.8 42.7 68 250TNC4 - 1632 06.07.0084.06 16 32 50 32.5 6.5 84.7 45.3 86 200TNC2 - 2032 06.07.0085.06 20 32 50 36.5 6.5 86.7 45.3 86 200TNC2 - 2532 06.07.0194.02 25 32 50 42 6.5 94 42 90 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2
TNC1 is with die cast pressure fingers and serrated mounting faceTNC2 is with die cast pressure fingers and mounting cavityTNC3 is with stamped pressure fingers and serrated mounting faceTNC4 is with stamped pressure fingers and mounting cavity
*
Design subject to change
Tandem Brush Holders
Type TRG2, TNH2, TNH4*
Made of brass die casting with self recoiling spring
25
Brush - dimensions Holder - dimensions Pressure
Type Article no. t a r u k b I pTRG2 - 0832 06.07.0191.00 8 32 64 42.7 90 82 11.5 225TRG2 - 1032 06.07.0189.00 10 32 64 42.7 90 82 11.5 225TRG2 - 1232 06.07.0179.01 12 32 64 42.7 90 82 11.5 225TNH2 - 1232 06.07.0113.02 12.5 32 64 42 84 68 11.5 225TNH4 - 1232 06.07.0111.02 12.5 32 64 42 84 68 11.5 225TNH2 - 1632 06.07.0114.01 16 32 64 45 86 74.4 13 200TNH4 - 1632 06.07.0112.02 16 32 64 45 86 74.4 12 200
Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2
TRG2 and TNH2 are with serrated mounting faceTNH4 is with mounting cavity*
Design subject to change
26
Top Rings
SMK no. D d Pole Wd TK51.60.0176.04 303 254 4 Loch 11 27451.60.0168.00 305 271 4 Loch 8 28851.60.5100.01 305 241 4 Loch 6 26051.60.5100.02 305 241 4 Loch 6 26051.60.5100.03 305 241 4 Loch 6 28451.60.5100.04 305 241 4 Loch 6 28451.60.5100.05 305 241 4 Loch 6 26051.60.5100.06 305 253 4 Loch 6 26051.60.5100.07 305 253 4 Loch 6 28451.60.5100.08 305 253 4 Loch 6 26051.60.5100.09 305 253 4 Loch 6 28451.60.5101.01 340 276 4 Loch 6 29451.60.5101.02 340 276 4 Loch 6 29451.60.5101.03 340 276 4 Loch 6 32051.60.0176.03 343 294 4 Loch 11 31451.60.0167.00 345 306 4 Loch 8 32651.60.5114.01 350 290 4 Loch 8 31051.60.5114.02 350 290 4 Loch 8 31051.60.0176.05 363 314 4 Loch 11 33551.60.0176.02 400 354 4 Loch 10 37351.60.0176.01 450 404 4 Loch 10 42551.60.0176.00 500 454 6 Loch 10 47051.60.0176.08 370 326 4 Loch 10 345
Design subject to change
27
Rocker Rings
SMK no. Outer Dia. D Inner Dia. d Pole R B b51.60.0178.00 64.5 40 2 6 1051.60.0178.01 64.5 40 2 6 1051.60.5162.00 76 43 2 8 851.60.5027.00 87 48 2 19 11.551.60.0174.00 88 58 4 6 651.60.5028.00 88 52 2 8 16 851.60.5102.00 100 55 2 17 551.60.5108.00 100 62 2 12 2451.60.5080.01 102 45 4 551.60.5104.00 114 72 4 10 30 1051.60.5120.01 135 95 2 10 18 1051.60.5120.02 135 95 2 10 18 1051.60.0151.00 140 100 4 13 39.75 1351.60.5007.00 140 100 4 13 16.5 1351.60.5007.02 140 100 4 13 1351.60.5043.00 140 100 4 13 26.5 1351.60.5044.00 140 100 4 16 16.5 1351.60.0179.00 150 92 2 10 13 751.60.5006.01 160 120 4 12 24 1251.60.5006.04 160 120 4 12 35 1251.60.5006.10 160 120 4 12 31 1251.60.5008.00 160 110 4 16.5 31.5 16.551.60.5022.00 160 140 4 12 26 1251.60.5047.00 160 110 2 14 14 1451.60.5146.00 160 110 4 16 19.5 1651.60.0180.00 165 107 2 10 13 751.60.0183.00 165 107 4 13 37.7 851.60.0184.00 165 92 2 13 40.2 851.60.5049.00 165 105 4 13 30 851.60.0082.00 170 115 2 12 10.5 651.60.5050.01 170 126 4 18 43 851.60.5050.02 170 126 4 18 43 851.60.5041.00 172 125/69 4 24 651.60.5042.00 172 125/84 4 24 651.60.0181.00 175 118 2 15 15 751.60.5023.00 180 140 4 12 16 1251.60.5023.02 180 140 4 12 16 1251.60.5138.00 185 120 4 9 551.60.5138.01 185 120 4 9 551.60.5053.01 190 140 4 16 37 1651.60.5053.02 190 140 4 16 43 1651.60.5016.00 193 145 4 18 47 851.60.5002.00 200 140 4 15 41 1051.60.5021.00 200 160 4 12 25 1251.60.5054.00 200 145 4 16 1651.60.0188.00 202 150 4 18 30 1851.60.5131.00 205 138 4 22 20 1051.60.5131.01 205 138 4 22 47 10
Design subject to change
28
Rocker Rings
51.60.5017.00 223 173 4 16 20 1651.60.5058.00 223 173 4 16 25 1651.60.0173.00 225 164 4 25 48 1051.60.5132.00 225 164 4 27 25 1051.60.5132.01 225 164 4 27 52 1051.60.5019.00 235 175 4 18 61 851.60.5019.02 235 175 4 18 28 851.60.0154.03 240 170 4 17 23 1051.60.0154.02 240.5 170 4 17 23 1051.60.5097.01 250 175.4 4 18 76 1051.60.5105.01 250 174 4 18 50 1051.60.0169.00 255 186 4 18 24 1451.60.0169.01 255 186 4 18 24 1451.60.0185.00 255 186 4 22 24 1451.60.0098.02 260 205 4 20 2051.60.5012.00 260 190 4 25 41.5 751.60.5089.01 270 205 4 20 31 2051.60.0097.01 275 204 21.551.60.0109.01 285 215 4 25 10.551.60.0109.00 287 215 4 24.3 26.6 11.351.60.0186.00 288 200 4 27 29.5 1451.60.5091.01 288 200 4 27 29.5 1451.60.0166.01 295 219 4 17 33.5 1451.60.0166.02 295 219 4 17 33.5 1451.60.5061.00 295 235 4 30 63.5 751.60.5062.00 295 235 4 30 37 751.60.0150.00 315 225 4 25 2051.60.0150.02 315 225 4 25 2051.60.5013.00 320 235 4 30 77 951.60.5014.00 320 235 4 30 50.5 951.60.5095.00 335 235 4 30 32 1451.60.5095.01 335 235 4 30 32 1451.60.0150.01 340 250 4 25 2051.60.0150.03 340 250 4 25 2051.60.5161.00 340 250 4 32 35 1451.60.5092.00 370 270 4 32 35 1451.60.5092.01 370 270 4 32 40 1451.60.5093.00 370 270 4 32 35 1451.60.5093.01 370 270 4 32 35 1451.60.5093.02 370 270 4 32 40 1451.60.5149.00 380 270 4 34 106.5 1051.60.5149.01 380 270 4 34 80.5 1051.60.5149.02 380 270 4 34 79.5 1051.60.5149.03 380 270 4 34 46 1051.60.5150.00 420 310 4 36 120 1051.60.5150.01 420 310 4 36 111.5 1051.60.5150.02 420 310 4 36 85.5 1051.60.5150.03 420 310 4 36 51 1051.60.0170.00 450 330 4 40 42 1451.60.0171.00 570 425 4 / 6 50 52 14
SMK no. Outer Dia. D Inner Dia. d Pole R B b
Design subject to change
29
1 2 3
4 5
6 7
30
8
10
12
14 15
13
11
9
31
16
21
26
31 32 33 34 35
27 28 29 30
22 23 24 25
17 18 19 20
32
36
40
44 45 46 47
41 42 43
37 38 39
33
48
54
60
66
72 73 74 75 76 77
67 68 69 70 71
61 62 63 64 65
55 56 57 59
49 50 51 52 53
34
78
82
85
88 89 90
86 87
83 84
79 80 81
35
Other Special Designs
Plug-inbrushholder
EarthingContacts
Roller-holders
Flange-brush-holder
Schunk Graphite Technology
W146 N9300 Held DriveMenomonee Falls, WI 53051
Phone: 262-253-8720Toll Free: 888-560-7744Fax: 262-644-6073
www.schunkgraphite.com