Auxiliary Fittings Dimensional Drawings · 2018-12-13 · Auxiliary Fittings Dimensional Drawings...

Auxiliary Fittings Dimensional DrawingsAuxiliary Fittings for Intake and Discharge Fitting Pads

Specify Installation of these fittings on main intake and discharge fitting pads to achieve a custom piping configuration.

These fittings are divided into type groups which are referred to on the intake and discharge fitting dimensional drawings. Refer to the table column *install aux fittings* on those drawings and using thetype group specified. Locate and choose additional fittings to be installed on those pads.

FITTING TYPE DESCRIPTION SEE PAGE

TYPE 1 2-1/2 in. 4-Bolt Machined Pads 2-5

TYPE 2 2-1/2 in. NPT Openings 6

TYPE 3 2 in. NPT Openings 6

TYPE 4 1-1/2 in. NPT Openings 6

TYPE 7 3-1/2 in. Discharge Valves (Includes Siamese) 7-9

TYPE 8 3, 3-1/2, or 4 in. 8-Bolt Machined Pads 10-15

TYPE 9 3 in. NPT Openings 15

TYPE 11 5 in. Flanged Ends on Intake Fittings 16

TYPE 12 6 in. Flanged Ends on Intake Fittings* 17

TYPE 13 6 in. Threaded Ends on Intake Fittings 18

TYPE 14 3 in. Relief Valve Pad 19

TYPE 15 4 in. Relief Valve Pad 20

TYPE 17 6 in. Flanged Ends on 6-3/4 in. Long Intake Fittings 21

TYPE 19 Dump Flange on Intake Nipples 22

TYPE 20 Relief Valve Spacers 22

TYPE 23 5 in. Threaded Ends on Intake Fittings 23

TYPE 24 4 in. ANSI Flanges 24-25

TYPE 25 3-1/2 in. Front Discharge 26-27

TYPE 30 82952 Oversized Pant Leg Intake Fittings, 8 in. Flange* 28

TYPE 36 2-1/2 in. Uni-Body (Akron/Elkhart) 4-Bolt Machined Pads 29

TYPE 70 Conductivity Probe Tap 30

TYPE 71 3 in. Uni-Body (Akron/Elkhart) 4-Bolt Machined Pads 30

*FOR JAMESBURY BUTTERFLY VALVES-SEE DRAWING DPL83723

11/19/18Rev. DateDocument Number

DPL82088Issue Date

WaterousCompany, 125 Hardman Avenue South, South St. Paul, Minnesota 55075 USA (651) 450-5000 www.waterousco.comDimensions subject to change without notice.

06/13/95

LSEE DETAIL 2(BOTH ENDS)

SEE DETAIL 2(BOTH ENDS)

2-1/2 NPT

6.000in152.40mm

3.000in76.20mm

2.688in68.26mm

8.000in203.20mmSEE DETAIL 1

(BOTH ENDS)

6.000in152.40mm

2.688in68.26mm

SEE DETAIL 2(BOTH ENDS

1.500in38.10mm

2X 3/8-16 UNC-2B X .625/15.88 DEEP

1.750in44.45mm

3.500in88.90mm

3.000in76.20mm

20.000in508mm

4.000in101.60mm

SEE DETAIL 3

SEE DETAIL 4

3.500in88.90mm

1.500in38.10mm

1.750in44.45mm

.500in12.70mm

.825in20.96mm

.438in11.11mm

1.125in28.58mm

22.5° TYP

4X 6-32 UNC-2B X .375/9.53 DEEPEQUALLY SPACED ON 1.600/40.64 B.C.

.141in[3.57mm] X .300in[7.62mm] DEEPON 1.420/36.07 B.C.

4.250in107.95mm

2.500in63.50mm

4X .500in[12.70mm]

THRUEQUALLY SPACED ON 4.375/111.13 B.C.

3.000in76.20mm

4.250in107.95mm

mUSE O-RING W-3756-4

DETAIL 32-1/2 IN. FLANGE, (4) BOLT

(WITH THRU HOLES)

4X .469in[11.91mm]

THRUEQUALLY SPACED ON 4.375/111.13 B.C.

2.500in63.50mm

4.250in107.95mm

USE GASKET 51218DETAIL 2

2-1/2 IN. FLANGE, (4) BOLT(WITH THRU HOLES)

4X .469in[11.91mm] THRUEQUALLY SPACED ON 4.375/111.13 B.C.

3.000in76.20mm

5.875in149.23mm

8X .531in[13.49mm] THRUEQUALLY SPACED ON 5.500/139.70 B.C.

.500in12.70mm

2.188in55.56mmQUICK RELEASE PIN INCLUDED

.438in11.11mm 1.623in

41.22mm

#6-32 ROUND HEAD SCREW(FOR GROUND WIRE)

NOTES:ALL FITTINGS ARE AVAILABLE IN IRON OR BRONZE UNLESS OTHERWISE SPECIFIED, ADD "-BZ" 1.SUFFIX TO PART NUMBER FOR BRONZE FITTINGS.SPECIFY WHERE EACH FITTING IS TO BE MOUNTED. ALL FITTINGS INCLUDE GASKET AND 2.MOUNTING HARDWARE.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.3.

TYPE 1 - FITTINGS FOR 2-1/2 IN. 4-BOLT MACHINED PADS

EXTENSIONS ADAPTERS FOR FLOWMETER PAD ON FITTINGS 71916-A AND 81799-A

PART NO. L INCLUDES GASKET

6038-3A 3.00/76.20512186038-4A 4.00/101.60

6038-6A 6.00/152.406038-6A 8.00/203.20

PART NO. INCLUDES GASKET

60346-A 51218

71037-A 51218

PART NO. DESCRIPTION INCLUDES GASKET

71916-A EXTENSION WITH FLOPWMETER PAD 51218

PART NO. DESCRIPTION INCLUDES O-RING

81799-A EXTENSION WITH FLOWMETER PAD W3756-4

PART NO. DESCRIPTION INCLUDES

72985-A FLOW SENSOR ADAPTER (CLASS1)

W3732-4 O-RING AND MOUNTING

HARDWARE

72571-A FLOW SENSOR ADAPTER (FOAMPRO FLOWMETER)

W3732-4 O-RING AND MOUNTING

HARDWARE

302 ofPageDPL82088

4X .563in 14.29mm THRUEQUALLY SPACED ON 4.375/111.13 B.C.(BOTH FLANGES TYP)

2.500in63.50mm

4.250in107.95mm

45.00°

3.500in88.90mm

5.563in141.29mm

2.500in63.50mm

m 4.250in107.95mm

4X .500in[12.70mm] THRUEQUALLY SPACED ON

4.375/111.13 B.C.

2.500in63.50mm4.875in

123.83mm4.

4.375/111.13 B.C.

5.250in133.35mm

4.125in104.78mm

4.250in107.95mm

4X .500in[12.70mm]THRUEQUALLY SPACED ON

4.375/111.13 B.C.

4.250in107.95mm

4.375/111.13 B.C.

NOTES:ALL FITTINGS ARE AVAILABLE IN IRON OR BRONZE 1.UNLESS OTHERWISE SPECIFIED, ADD "-BZ" SUFFIX TO PART NUMBER FOR BRONZE FITTINGS.SPECIFY WHERE EACH FITTING IS TO BE 2.MOUNTED. ALL FITTINGS INCLUDE GASKET AND MOUNTING HARDWARE.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.3.

ELBOWS

70436-A 45 ELBOW 51218

71017-A 90 LONG SWEEP 51218

PART NO. DESCRIPTION INCLUDES GAKET

61424-A 90 SHORT ELBOW 51218

PART NO. DESCRIPTION TAP A INCLUDES

71443-A 90 MEDIUM ELBOW ---

5121871443-1A 90 MEDIUM

ELBOW 1 NPT

303 ofPageDPL82088

4.250in107.95mm

4X .469in 11.91mm THRUEQUALLY SPACED ON

4.375/111.13 B.C.

.563in14.29mm

4.375/111.13 B.C.

4.250107.95 4.

1.250in31.75mm .500in

12.70mm

4.250in107.95mm

4.375/111.13 B.C.

2-1/2 NPT

1.250in31.75mm .500in

12.70mm

4.375/111.13 B.C.4.250in

107.95mm

2-1/2 NPT Tapped Hole

(USE (4) 7/16-14 SOCKET HEAD SCREWS)

1.410in35.81mm

4.375/111.13 B.C.

4.250in107.95mm

1.875in47.63mm

4.375/111.13 B.C.

4.250in107.95mm

.500in12.70mm

1.250in31.75mm

4.375/111.13 B.C.

4.250in107.95mm

1.910in48.51mm

2.093in53.15mm

4.375/111.13 B.C.

4.250in107.95mm

1.125in28.58mm

NOTES:THIS ANODE MAY BE MOUNTED ON 1.ANY FITTING WITH A 2-1/2 IN. (4) BOLT FLANGEANODE ASSEMBLY INCLUDES GASKET 2.AND MOUNTING HARDWARE (USE O-RING W3756-4 AS GASKET)

USE (4) 7/16-14 HEX HEAD SCREWS

FLANGES

62939-A BLIND FLANGE W-3756-4

PART NO. DESCRIPTION TAP A INCLUDES O-RING

63048-ATAPPED FLANGE

1.5 NPTW-3756-4

62897-A 2 NPT

PART NO. DESCRIPTION TAP A INCLUDES O-RING

62605-A ANGLE COMPENSATED

TAPPED FLANGE

2.5 NPTW3756-4

62605-1A 3 NPT

61473-A 2.5 NPT TAPPED FLANGE W-3756-4

61636-A 3 NPT TAPPED FLANGE W-3756-4

63205-A 2-1/2 IN. BSP TAPPED FLANGE W3756-4

PART NO. DESCRIPTION PUMP MAT'L

82904-1A 2-1/2 IN. (4) BOLT FLANGE IRON

63049-A SPACER 51218

304 ofPageDPL82088

(AVAILABLE ON INTAKE FITTING PADS ONLY)

MOUNTING AN INTAKE RELIEF VALVE

REFER TO DIMENSIONAL DRAWING DPL82084-5

MOUNTING A 2-1/2 IN. DISCHARGE VALVE

REFER TO 2-1/2 IN. DISCHARGE VALVE DIMENSIONAL DRAWING FOR VALVE PART NUMBERS

PART NO.

82256-1

305 ofPageDPL82088

FITTING (REF)NPT SIZE(SEE TABLE)

2 REPLACEABLE ANODES

NOTE: THIS ANODE ASSEMBLY MAY BE INSTALLED IN ANY FITTING WITH A 2-1/2

NPT TAP

SQUARE HEAD HEADLESS SQUARE HEAD

SQUARE HEAD HEADLESS

TYPE 2 - FITTINGS FOR 2-1/2 NPT OPENINGS

ZINC ANODE ASSEMBLY PIPE PLUGS

PIPE PLUGS PIPE PLUGS

TYPE 3 - FITTINGS FOR 2 IN. NPT OPENINGS TYPE 4 - FITTINGS FOR 1-1/2 IN. NPT OPENINGS

NOTE: ALL DIMENSIONS SHOWN AS INCH/MILLIMETER

PART NO. DESCRIPTION A B

52315 2-1/2 NPT 1.810/45.97 4.090/103.89

PART NO. DESCRIPTION TYPE MAT'L

W6540-G

2-1/2 NPTSQUARE HEAD

GALVANIZED IRON

W6540-B BRASS

W6640 HEADLESS IRON

SQUARE HEADIRON

W6532-B BRASS

W6632HEADLESS

W6632-B BRASS

W65241-1/2 NPT SQUARE HEAD

W6524-B BRASS

306 ofPageDPL82088

1.125in28.58mm

THIS FLANGE TO BE MOUNTEDTO PUMP BODY

ROUND THIS LENGTHROUND THIS LENGTH

5.500/139.70 B.C.

45° TYP26.5°

SEE DETAIL 4

m 5.00

1.125in28.58mm

MOUNT EITHER FLANGE TO PUMP BODY SEE DETAIL 4

(BOTH FLANGES)

5.500/139.70 B.C.

m 18.5°45° TYP

3.500in88.90mm

1.125in28.58mm

THIS FLANGE TO BE MOUNTEDTO PUMP BODY

THIS TOP VIEW CAN BE USED FOR ALL 3 SIAMESE FITTINGS SHOWN

5.5../139.70 B.C.

5.875in149.23mm

3.500in88.90mm

R3.250in82.55mm

USE GASKET 51195 OR 52108DETAIL 4

3-1/2 IN. FLANGE (8) BOLT

SIAMESEFITTING

3-1/2 IN. DISCHARGE VALVES

CENTER DISCHARGE PIPING

PUMP DISCHARGE FLANGE WITH OR WITHOUTANGLE COMPENSATION

*OTHER THREADS AVAILABLE ON SPECIAL ORDERWITH 4 ANGLE COMPENSATION

LEFT SIDE MOUNTING ONLY(SEE DETAIL 2) WITH 4 ANGLE COMPENSATION

RIGHT SIDE MOUNTING ONLY(SEE DETAIL 2)

*OTHER THREADS AVAILABLE ON SPECIAL ORDER

WITHOUT ANGLE COMPENSATIONLEFT SIDE OR RIGHT SIDE MOUNTING

(SEE DETAIL 2)*OTHER THREADS AVAILABLE ON SPECIAL ORDER

NOTES:ALL FITTINGS ARE AVAILABLE IN IRON OR BRONZE 1.UNLESS OTHERWISE SPECIFIED, ADD "-BZ" SUFFIX TO PART NUMBER FOR BRONZE FITTINGS.SPECIFY WHERE EACH FITTING IS TO BE MOUNTED. 2.ALL FITTINGS INCLUDE GASKET AND MOUNTING HARDWARE.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.3.

TYPE 7 - FITTINGS FOR 3-1/2 IN. DISCHARGE VALVES

SIAMESE FITTINGS

DETAIL 2NORMAL SIAMESE CONFIGURATION(RIGHT OR LEFT SIDE, LEFT SHOWN)

PART NO. THREAD SIZE* A L INCLUDES GASKET

81576-A 5 IN. NH 7.500/190.50 20.000/508.00 51195

71933-A 5 IN. NH 5.500/139.70 18.000/457.20 51195

81573-A5 IN. NH

5.500/139.70 18.000/457.2051195

81575-A 7.500/190.50 20.000/508.00

307 ofPageDPL82088

8X .531in 13.49mm THRUEQUALLY SPACEDON 5.500/139.70 B.C.

5.875in149.23mm

R3.250in82.55mm

DRAIN TAPA

.500in12.70mm

5.875in149.23mm

3.500in88.90mm

R3.250in82.55mm

5.875in149.23mm

R3.250in82.55mm

1.250in31.75mm

8X .531in 13.49mm THRUEQUALLY SPACEDON 5.500/139.70 B.C.USE (8) 1/2-13 SOCKET HEAD SCREWS

5.875in149.23mm

R3.250in82.55mm

8X .750in 19.05mm THRUEQUALLY SPACED ON 7.500/190.50 B.C.

6.500in165.10mm 9.000in

228.60mm

2.500in63.50mm

8X .531in 13.49mm THRUEQUALLY SPACED ON 5.500/139.70 B.C

6.500in165.10mm

9.000in [ 228.60mm] 3.

3.02176.73

4.000in101.60mm

FLANGES ADAPTERS

* AVAILABLE IN IRON ONLY

PART NO. DESCRIPTION DRAIN TAP A

INCLUDES GASKET

52042-1A BLIND FLANGE WITH DRAIN 3/8 NPT 51195

PART NO. DESCRIPTION TAP A INCLUDES GASKET

*52556-A

TAPPED FLANGE

2-1/2 NPT

51195*51744-A 3 NPT

*51744-1A 3-1/2 NPT

51744-4C 4 NPT

72402-AWATEROUS 3-1/2 (8) BOLT TO 4 IN.

ANSI FLANGE ADAPTER

72797-A

WATEROUS 3-1/2 (8) BOLT TO 4 IN.

ANSI ANGLE COMPENSATED

FLANGE ADAPTER

PART NO. DESCRIPTION INCLUDES GASKET L

51754-ASPACER 51195

1.062/26.97

52703-A .750/19.05

72098-AANGLE

COMPENSATED TAPPED FLANGE

3-1/2 NPT

5210872257-A 3 NPT

72844-A 3 IN. BSP

308 ofPageDPL82088

LSEE DETAIL 3(BOTH ENDS)

3.000in76.20mm

8.000in203.20mm

4.000in101.60mm

9.500in241.30mm

8.000in203.20mm

1.125in28.58mm

SEE DETAIL 4

2.750in69.85mm

5.500in139.70mm

SEE DETAIL 3(BOTH ENDS) TAP

4.000in101.60mm

5.875in149.23mm

3.500in88.90mm

R3.250in82.55mm

3-1/2 IN. FLANGE, (8) BOLT

2.875in73.03mm

1.750in44.45mm 3.500in

88.90mm

4.000in101.60mm

8.000in203.20mm

1.500in38.10mm

2X 3/8-16 UNC-2B

3/8-16 Tapped Hole

1.125in28.58mm

.438in11.11mm

.825in20.96mm

.500in12.70mm

.141in 3.57mm .300in 7.62mm ON 1.420/36.07 B.C.

4X 6-32 UNC-2B .375in 9.53mm

EQUALLY SPACED ON 1.600/36.07 B.C.

22.5° TYP.500in

12.70mm

2.188in55.56mm

QUICK RELEASEPIN INCLUDED

5mm .438in

11.11mm

1.623in41.22mm

#6-32 ROUND HEAD SCREW(FOR GROUND WIRE)

EXTENSIONS ELBOWS

THREADED EXTENSIONS

*AVAILABLE IN IRON ONLY*AVAILABLE IN IRON ONLY

62407-A 6.000/152.4051195

62408-A 4.000/101.60

70828-A 51195

PART NO. THREAD SIZE D INCLUDES

GASKET

72072-A 3-1/2 IN. NH 4.250/107.9551195

72071-A 4 IN. NH 4.750/120.65

71597-A 51195

PART NO. TAP A INCLUDES GASKET

62052-A ---51195

*62052-1A 2-1/2 NPT PART NO. INCLUDES GASKET

71599-A 51195

PART NO. TAP A B INCLUDES GASKET

72067-A 1-1/4 11-1/2 NPSM 2.250/57.15

5119572067-1A 1-1/4 NPT 2.375/60.33

*72540-A --- ---

62551-A EXTENSION WITH FLOWMETER PAD 51195

72985-AFLOW SENSOR

ADAPTER (CLASS 1)

W3732-4 O-RING WITH MOUNTING

HARDWARE

72571-AFLOW SENSOR

ADAPTER (FOAMPRO

FLOWMETER)

W3732-4 O-RING WITH MOUNTING

HARDWARE

309 ofPageDPL82088

5.875in149.23mm

R3.250in82.55mm

1.250in31.75mm

8X .531in 13.49mm THRUEQUALLY SPACED ON 5.500/139.70 B.C.USE (8) 1/2-13 SOCKET HEAD SCREWS

5.875in149.23mm

R3.250in82.55mm

6.500in165.10mm

9.000in228.60mm 3.

2.500in63.50mm

5.875in149.23mm3.500in

88.90mm

R3.250in82.55mm

8X .531in 13.49mm THRUEQUALLY SPACED ON 5.500/139.70 B.C.8X .750in 19.05mm THRU

6.500in165.10mm

9.000228.60

4.000in101.60mm

5.875in149.23mm R3.250in

82.55mm

3/8 NPT Tapped Hole

.500in12.70mm

TYPE 8 - FITTINGS FOR 3, 3-1/2, OR 4 IN. 8-BOLT MACHINED PADS

FLANGES ADAPTERS

*AVAILABLE IN IRON ONLY

INCLUDES GASKET

52042-1A BLIND FLANGE WITH DRAIN 3/8 NPT 51195

*52556-A

TAPPED FLANGE

2-1/2 NPT

51195*51744-A 3 NPT

*51744-1A 3-1/2 NPT

51744-4C 4 NPT

72098-A ANGLE COMPENSATED

TAPPED FLANGE

3-1/2 NPT

5210872257-A 3 NPT

72844-A 3 IN. BSP

72402-AWATEROUS 3-1/2 (8) BOLT TO 4 IN.

ANSI FLANGE ADAPTER

PART NO. DESCRIPTION L INCLUDES GASKET

51754-ASPACER

1.062/26.9751195

52703-A .750/19.05

72797-A

WATEROUS 3-1/2 (8) BOLT TO 4 IN.

FLANGE ADAPTER

3010 ofPageDPL82088

SEE DETAIL3(BOTH ENDS)

3.000in76.20mm

8.000in203.20mm

4.000in101.60mm

8.000in203.20mm

1.125in28.58mm

SEE DETAIL4

5.500in139.70mm

2.750in69.85mm

4.000in101.60mm

8.000in203.20mm

5.875in149.23mm

R3.250in82.55mm

3.500in88.90mm

EXTENSIONS ELBOWS

AVAILABLE IN IRON ONLY

THREADED EXTENSIONS

62407-A 6.000/152.4051195

62408-A 4.000/101.60

PART NO. THREAD SIZE D INCLUDES

GASKET

72072-A 3-1/2 IN. NH 4.250/107.9551195

72071-A 4 IN. NH 4.750/120.65

PART NO. TAP A B INCLUDES GASKET

72067-A 1-1/4 11-1/2 NPSM 2.250/57.15

5119572067-1A 1-1/4 NPT 2.375/60.33

*72540-A --- ---

71597-A 51195

PART NO. TAP A INCLUDES GASKET

62052-A 2-1/2 NPT 51195

71599-A 51195

3011 ofPageDPL82088

4°ANGLE

COMPENSATED SHOWN

INTAKE FITTING FROM EITHERSECTION 1 OR SECTION 2OF DPL81867

PUMP MOUNTING PAD

SEE FLANGE DETAIL

FLANGEFORWARD

CL INTAKE

4°ANGLE

COMPENSATED SHOWN

SEE FLANGE DETAIL

FLANGEFORWARD

CL INTAKE

5.500/139.70EXTENSION

PUMP MOUNTING PAD

4.500in114.30mm 4.500in

114.30mm 4X 7/16-14 UNC -2B THRUEQUALLY SPACED ON 4.375/111.13 B.C.

MANIFOLD FLANGE DETAIL

1/4 NPTDRAIN(UNDERSIDE)

TYPE 8 - FITTINGS FOR 3, 3-1/2, OR 4 IN. 8-BOLT MACHINED PADSSINGLE INTAKE MANIFOLD ASSEMBLY 81990 (AVAILABLE ON INTAKE FITTINGS ONLY)

W/O EXTENSION WITH EXTENSION

NOTE:ALL DIMENSIONS SHOWN AS INCH/MILLIMETER

NOTE:ANGLE COMPENSATEDASSEMBLIES WITH REARFACING FLANGES ARE NOT CURRENTLY AVAILABLE.NON-ANGLE COMPENSATED ASSEMBLIES MAY FACEFRONT OR REAR

NOTES:LEFT SIDE MOUNTING IS SHOWN IN 1.DETAILS ABOVE.IRON ASSEMBLIES ARE ONLY 2.AVAILABLE AT THIS TIME.

FORWARD

4 ANGLE COMPENSATION MOUNTING B DIA E

ASSEMBLY NO. A ASSEMBLY NO. A

11.740/298.20

2.500/63.50 81990-1A

9.946/252.63

81990-2A

15.446/392.333.000/76.20 81990-1B 81990-2B

RIGHT2.500/63.50 81990-1C 81990-2C

3.000/76.20 81990-1D

9.106/231.29

81990-2D

NO LEFT OR RIGHT 12.220/310.39

2.500/63.50 81990-1E 81990-2E14.606/370.99

3.000/76.20 81990-1F 81990-2F

3012 ofPageDPL82088

DIA E DIA E4°ANGLE

COMPENSATED SHOWN

PUMP MOUNTING PAD

SEE FLANGE DETAILFLANGE FORWARD

CL INTAKE

DIA EDIA E

4°ANGLE

COMPENSATEDSHOWN

PUMP MOUNTING PAD

SEE FLANGE DETAILFLANGEFORWARD

5.500/139.70EXTENSION

CL INTAKENOTE:ANGLE COMPENSATEDASSEMBLIES WITH REARFACING FLANGES ARE NOT CURRENTLY AVAILABLE.NON-ANGLE COMPENSATED ASSEMBLIES MAY FACEFRONT OR REAR

4.500in114.30mm

8X 7/16-14 UNC -2B THRUEQUALLY SPACED ON 4.375/111.13 B.C.

MANIFOLD FLANGE DETAIL

1/4 NPT DRAIN(UNDERSIDE)

WITH EXTENSIONW/O EXTENSION

TYPE 8 - FITTINGS FOR 3, 3-1/2, OR 4 IN. 8-BOLT MACHINED PADSDUAL INTAKE MANIFOLD ASSEMBLY 81990 (AVAILABLE ON INTAKE FITTINGS ONLY)

NOTES:LEFT SIDE MOUNTING IS SHOWN IN DETAILS ABOVE.1.IRON ASSEMBLIES ARE ONLY AVAILABLE AT THIS TIME.2.

FORWARD

4 ANGLE COMPENSATION MOUNTING B C D DIA E

ASSEMBLY NO. A ASSEMBLY NO. A

11.740/298.20 6.980/177.29 .490/12.45

2.500/63.50 81990-1G

10.436/265.07

81990-2G

15.936/404.773.000/76.20 81990-1H 81990-2H

RIGHT2.500/63.50 81990-1J 81990-2J

3.000/76.20 81990-1K 81990-2K

NO LEFT OR RIGHT 12.220/310.39 7.000/177.80 0.000

2.500/63.50 81990-1L9.106/231.29

81990-2L14.606/370.99

3.000/76.20 81990-1M 81990-2M

3013 ofPageDPL82088

11.186284.12

SEE FLANGE DETAIL

PUMP MOUNTING PAD

INTAKE FITTING FROM EITHER SECTION 1 OR SECTION 2 OF DPL81867

8.000203.20

6.000152.40

12.000in304.80mm

18.500in469.90mm

CL OF PUMP

6.000in152.40mm

3.500in88.90mmR3.250in

82.55mm USE GASKET 51195 OR 52109FLANGE DETAIL

3-1/2 IN. FLANGE (8) BOLT

TYPE 8 - FITTINGS FOR 3, 3-1/2, OR 4 IN. 8-BOLT MACHINED PADSAUXILIARY INTAKE W/ SINGLE 3-1/2 IN. OPENING ASSEMBLY 82605

(AVAILABLE ON LEFT OR RIGHT INTAKE FITTING W/ OPENING FLANGE TO FRONT ONLY)

NOTES:LEFT SIDE MOUNTING IS SHOWN.1.IRON ASSEMBLY ONLY AVAILABLE AT THIS TIME.2.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.3.

ASSEMBLY NO. A

82605-1A 11.237/285.42

82605-1B 13.113/333.70

3014 ofPageDPL82088

A FITTING (REF)

NPT SIZE (SEE TABLE)

2 REPLACEABLE ANODES

SPECIFY TYPE 7 FITTINGS ON THIS PAD IF NECESSARY

TYPE 9 - FITTINGS FOR 3 IN. NPT OPENINGS

PIPE PLUGS ZINC ANODE ASSEMBLY

SQUARE HEAD

NOTE:THIS ANODE ASSEMBLY MAY BE INSTALLED IN ANY FITTING WITH A 3 NPT TAP1.

MOUNTING A 3-1/2 IN. DISCHARGE VALVE

REFER TO 3-1/2 IN. DISCHARGE VALVE DIMENSIONAL DRAWINGS FOR VALVE PART NUMBERS

NOTE:ALL DIMENSIONS SHOWN AS INCH/ MILLIMETER1.

PART NO. TYPE SIZE MAT'L

W6548SQUARE HEAD 3 NPT

W6548-B BRASS

PART NO. SIZE A B

52315-1 3 NPT 1.750/44.45 4.090/103.89

3015 ofPageDPL82088

DIA D 8X .875in22.23mm

1.125in28.58mm

.500in12.70mm

3/4 IN. NPT DRAIN

TYPE 11 - FITTINGS FOR 5 IN. FLANGED ENDS ON INTAKE FITTINGS

NIPPLES WITHOUT DUMP VALVE FLANGE

(USE WITH FLANGED SECTION 1 AND SECTION 2 FITTINGS ON DPL81867)

NIPPLE PART NO.

THREAD SIZE B LFLANGE INCLUDES

GASKETMOUNTED ON BUTTERFLY VALVE

NOYESINTAKE FITTING LENGTH

OTHER THAN 6.750 6.750 DIA D DIA E

72454-A N/A N/A 5.0 IN. NH 1.000/25.40 3.500/88.90 10.000/254.00 8.500/215.90 51720

3016 ofPageDPL82088

8X .875in22.23mm

.500in12.70mm1.125in

28.58mm

3/4 NPT DRAIN

DIA D HOLE L

3/4 NPT DRAIN (BOTH SIDES)

8.312in211.13mm SPECIFY TYPE 19

FITTINGS IFNECESSARY

8X .875in22.23mm9.500in

241.30mm

11.000in279.40mm

3.094in

78.58mm

3.094in

78.58mm

4.250in

107.95mm4.250in

107.95mm

4X .469in11.91mm

ON 4.375/111.13 B.C.

SECTION A-A

2.500in[63.50mm]

NIPPLES WITH DUMP VALVE FLANGE

NIPPLE EXTENSION

*NOTE: 61984-AA CONSISTS OF (2) 1 IN. 61984-A EXTENSIONS.(USE WITH FLANGED SECTION 1 AND SECTION 2 INTAKE FITTINGS ON DPL81867)

6 IN. JAMESBURY BUTTERFLY VALVES.SEE DRAWING DPL83723

(USE WITH FLANGED SECTION 1 AND SECTION 2 INTAKE FITTINGS ON DPL81867)

NIPPLE PART NO.

THREAD SIZE B L

FLANGE INCLUDES GASKET

MOUNTED ON BUTTERFLY VALVENO

YESINTAKE FITTING

LENGTHOTHER

THAN 6.750 6.750 DIA D DIA E

72453-A

SEE TYPE 17

FITTINGSSEE DPL

83723 6.0 IN. NH

1.000/25.40 3.375/85.73

11.000/279.40 9.500/241.30 91090272572-A

.875/22.23

5.250/133.35

72578-A 6.250/158.75

72579-A 7.250/184.15

EXTENSION PART NO. SIZE L FLANGE INCLUDES

GASKETDIA D DIA E HOLE61984-A

6.0 IN.1.000/25.40

11.000/279.40 9.500/241.30 (8) .875/22.23 910902*61984-AA 2.000/50.80

NIPPLE PART NO.THREAD SIZE L INCLUDES

GASKETMOUNTED ON BUTTERFLY VALVENO YES

72818-A

SEE DPL837235.0 IN. NH

5.250/133.35

91090272819-A 6.250/158.7572820-A 7.250/184.1572716-A

6.0 IN. NH5.250/133.35

72717-A 6.250/158.7572718-A 7.250/184.15

3017 ofPageDPL82088

3.025in76.84mm

3.84397.61

4.656in118.26mm

6 IN. NH THREAD(FEMALE)

.2506.35.2

5mm 5.

INTERNAL LUGS ON72564-A ONLY A

6 IN. NH THREAD MALE

6 IN. NH THREAD FEMALE

CAP ASSEMBLY - 6IN. STORZ STORZ ADAPTER

THREADED INTAKE FITTING EXTENSIONS

USED TO EXTEND 6 IN. NH THREADED FITTINGS(IRON ONLY AVAILABLE)

PART NO. DESCRIPTION

V3781 CAP ASSY. 6 IN. STORZ

PART NO. DESCRIPTION THREAD SIZE

V3782 ADAPTER 6 IN. STORZ W/LOCK X 6 IN. NH FEMALE

PART NO. THREAD SIZE A (EXT. LENGTH)

B (OVERALL LENGTH)

INCLUDES GASKET

72534-A6 IN. NH

3.750/92.25 4.750/120.6563011

72564-A 6.500/165.10 7.625/193.68

3018 ofPageDPL82088

3.37585.73

4.250in107.95mm

4X .500in12.70mm

.563in14.30mm

3.375in85.73mm

4.375in111.13mm

4X .531in13.49mm

1.875in47.63mm

3.375in85.73mm

4X .500in12.70mm

4.375in111.13mm

3.000in76.20mm L

3.375in85.73mm

4.375in111.13mm

3.000in76.20mm

4X .500in12.70mm

LRELIEF VALVE

TYPE 14 - FITTINGS FOR 3 IN. RELIEF VALVE PADS

RELIEF VALVE PAD BLIND FLANGES RELIEF VALVE PAD TAPPED FLANGES RELIEF VALVE PAD EXTENSIONS

USED ON 3 IN. RELIEF VALVE PADWHEN RELIEF VALVE IS NOT FURNISHED

USED ON 3 IN. RELIEF VALVE PAD

*NOTE: 61647-AA CONSISTS OF (2) 1 IN. 61947-A EXTENSIONS.(USE WITH SECTION 1 INTAKE FITTINGS ON DPL81867)

(USE WITH SECTION 1 INTAKE FITTINGS ON DPL81867)

MOUNT RELIEF VALVE BETWEEN INTAKE AND DISCHARGE FITTINGS

REFER TO DIMENSIONAL DRAWING DPL82084-1 FOR ADDITIONAL DETAILS

62950-A BLIND FLANGE W3756-4

62206-A 3 NPT TAPPED FLANGE W3756-4

PART NO. L INCLUDED STUDS

USE WITH INTAKE

EXTENSIONINCLUDES

O-RING

61647-A 1.000/25.40 (2) 51312 5002-AW3754-4

*61647-AA 2.000/50.80 (2) 51312-1 5003-A

PART NO. L USE WITH INTAKE EXTENSION

INCLUDES O-RING

61646-A 4.000/101.60 5005-A W3754-4

3019 ofPageDPL82088

5.500in139.70mm

7.000in177.80mm

4X .750in19.05mm

.656in16.66mm

5.500in139.70mm

7.000in177.80mm

4X .750in19.05mm

4.000in101.60mm

1.000in25.40mm

RELIEF VALVE

TYPE 15 - FITTINGS FOR 4 IN. RELIEF VALVE PADS

RELIEF VALVE PAD BLIND FLANGES RELIEF VALVE PAD EXTENSIONS

USED ON 4 IN. RELIEF VALVE PADWHEN RELIEF VALVE IS NOT FURNISHED

SPACER REQUIRED WHEN AN INTAKE EXTENSION IS ORDERED AND RELIEF VALVE IS MOUNTED ON PUMP

1 IN. INTAKE EXTENSION ORDERED

NOTE:4 IN. RELIEF VALVE EXTENSIONS ARE NOT CURRENTLY AVAILABLE.4 IN' LONG EXTENSION 62408-A MAY BE USEDBETWEEN THE PUMP BODY AND THE DISCHARGEFITTING TO COMPENSATE FOR INTAKE EXTENSION 7251-A.

4 IN. INTAKE EXTENSION ORDERED

MOUNT RELIEF VALVE BETWEEN INTAKE AND DISCHARGE FITTINGSREFER TO DIMENSIONAL DRAWING DPL82084-2 FOR ADDITIONAL DETAILS

MOUNT RELIEF VALVE ORDERED

63842-A RELIEF VALVE SPACER W3772-4

3020 ofPageDPL82088

.500in12.70mm1.125in

28.58mm

3/4 NPT DRAIN

8X .875in22.23mm

8.312211.12

3/4 NPT DRAIN(BOTH SIDES)

SPECIFY TYPE 19 FITTINGS IF NECESSARY

8X .875in22.23mm

9.500in241.30mm

11.000in279.40mm

3.094in

78.58mm3.094in

78.58mm 4.250

107.95

4.250in

107.95mm

4X .469in 11.91mmON 4.375/111.13 B.C.

VIEW A-A

2.500in.[63.50mm]

TYPE 17 - FITTINGS FOR 6 IN. FLANGED ENDS ON 6-3/4 IN. LONG INTAKE FITTINGS

NIPPLES WITH DUMP VALVE FLANGE

(USE WITH FLANGED SECTION 1 AND SECTION 2 INTAKE FITTINGS ON DPL81867)

(USE WITH FLANGED SECTION 1 AND SECTION 2 INTAKE FITTINGS ON DPL81867)6 IN. JAMESBURY BUTTERFLY VALVESSEE DRAWING DPL83723

NIPPLE PART NO.THREAD SIZE L INCLUDES

72818-A

SEE DPL837235.0 IN. NH

5.250/133.35

91090272819-A 6.250/158.7572820-A 7.250/184.1572716-A

6.0 IN. NH5.250/133.35

72717-A 6.250/158.7572718-A 7.250/184.15

NIPPLE PART NO.

THREAD SIZE B L

FLANGE INCLUDES GASKET

MOUNTED ON BUTTERFLY VALVENO

YESINTAKE FITTING

LENGTHOTHER

THAN 6.750 6.750 DIA D DIA E

SEE TYPE 12

FITTINGS

72453-2A

SEE DPL 83723 6.0 IN. NH

1.000/25.40 3.375/85.73

11.000/279.40 9.500/241.30 91090272572-2A

.875/22.23

5.250/133.35

72578-2A 6.250/158.75

72579-2A 7.250/184.15

3021 ofPageDPL82088

TYPE 19 - FITTINGS FOR DUMP FLANGE ON INTAKE NIPPLESINTAKE RELIEF VALVE

TYPE 20 - FITTINGS FOR RELIEF VALVE EXTENSIONMOUNT DISCHARGE RELIEF VALVE

MOUNT INTAKE RELIEF VALVEREFER TO DIMENSIONAL DRAWING DPL82084-5 MOUNT RELIEF VALVE ON EXTENSION BETWEEN INTAKE AND DISCHARGE FITTINGS

REFER TO DIMENSIONAL DRAWING DPL82084-1 OR DPL82084-2 FOR ADDITIONAL DETAILS

PART NO.

82256-3

3022 ofPageDPL82088

5 IN. NH THREAD(MALE)

5 IN. NH THREAD(FEMALE)

TYPE 23 - FITTINGS FOR 5 IN. THREADED ENDS ON INTAKE FITTINGS

THREADED INTAKE FITTING EXTENSIONS

USE TO EXTEND 5 IN. NH THREADED FITTINGS(IRON ONLY AVAILABLE)

EXTENSION PART NO. THREAD SIZE A

(EXT. LENGTH)B

(OVERALL LENGTH)

INCLUDES GASKET

72798-A 5 IN NH. 6.500/165.10 7.625/193.68 63203

3023 ofPageDPL82088

9.000in228.60mm

.938in23.83mm

7.000in177.80mm

2X 2 NPTSEE DETAIL B(TYP (2) ENDS)

SEE DETAIL C(TYP (2) SIDES)

3.500in88.90mm

7.000in177.80mm

10.125in257.18mm

10.500in266.70mm

14.250in361.95mm

28.500in723.90mm

SEE DETAIL A(TYP (8) PADS)

1/2-13 UNC-2B

7.750in196.85mm

2.500in63.50mm

4.250in107.95mm

DETAIL A

4X 7/16-14 UNC-2BEQUALLY SPACED ON

4.375/111.13 B.C.

4.000in101.60mm

6.500in165.10mm

DETAIL B

DETAIL C

8X 1/2-13 UNC-2B THRUEQUALLY SPACED ON

5.500/139.70 B.C.

4.000in101.60mm

9.000in228.60mm

8X 5/8-11 UNC-2B THRUEQUALLY SPACED ON

7.500/190.50 B.C.

TYPE 24 - FITTINGS FOR 4 IN. ANSI FLANGE

FLANGE

NOTES:ALL FITTINGS INCLUDE GASKET AND MOUNTING HARDWARE.1.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.2.

(IRON ONLY AVAILABLE)

V3338-A BLIND FLANGE 4 IN. ANSI 62476

82522 DISCHARGE MANIFOLD

3024 ofPageDPL82088

7.500/190.50 B.C.

5.500/139.70 B.C.

6.500in165.10mm

9.000in228.60mm

2.500in63.50mm

7.500/190.50 B.C.

5.500/139.70 B.C.

6.500in165.10mm

9.000228.60

4.000in101.60mm

3.021in76.73mm

5.000127

4.071in103.40mm

.750in 19.05mm THRUEQUALLY SPACED ON

7.500/190.50 B.C.

9.000in228.60mm

.875in 22.23mm THRUEQUALLY SPACED ON

8.500/215.90 B.C.

10.000in254mm

TYPE 24 - FITTINGS FOR 4 IN. ANSI FLANGE

ADAPTERS

72402-1A4 IN. ANSI FLANGE TO 3-1/2 (8) BOLT

ADAPTER62476

72797-1A4 IN. ANGLE

COMPENSATED FLANGE TO 3-1/2

(8) BOLT ADAPTER62476

72885-A4 IN. ANSI TO 5 IN.

FLANGE ADAPTER62476

3025 ofPageDPL82088

5.500/139.70 B.C.

5.875in149.23mm R3.250in

82.55mmDRAIN TAP

.500in12.70mm

5.500/139.70 B.C.

5.875in149.23mm

R3.250in82.55mm

1.250in31.75mm

5.500/139.70 B.C.

5.875in149.23mm

4.000in101.60mm

5.062in128.57mm

8X .531in [13.49mm] THRUEQUALLY SPACED ON

5.500/139.70 B.C.ELBOW

SPACER

8.000in203.20mm

4.000in101.60mm

2-1/2 NPT8X .531in 13.49mm THRUEQUALLY SPACED ON

5.500/139.70 B.C.(TYP ALL FLANGES)

9.062230.17

32.250819.15

FRONT DISCHARGE PIPING ASSY

2-1/2 NPT

4 IN. NH THREAD

3-1/2 IN. ELECTRIC DISCHARGE VALVE 82617-2B.4

TYPE 25 - FITTINGS FOR 3-1/2 IN. FRONT DISCHARGE ON CM/CS PUMPS

EXTENSION

ELBOW TEES

FLANGES

AVAILABLE IN IRON ONLY

SPECIFY MOUNTING: OUTLET LEFT, RIGHT,.UP OR DOWN. ALSO SPECIFY WHICH LEG LENGTH,SHORT OR LONG TO BE FORWARD.

INCLUDES O-RING

52042-2A BLIND FLANGE WITH DRAIN 3/8 NPT W3770-4

PART NO. DESCRIPTION TAP AINCLUDES GASKET

OR O-RING

52556-1A

TAPPED FLANGE

2-1/2 NPT

W3770-4*51744-2A 3 NPT

*51744-3A 3-1/2 NPT

51744-4A 4 NPT 51195

62408-AA EXTENSION, 4 IN. W3770-4

82621-1AFRONT

DISCHARGE PIPING ASSEMBLY

W3770-4

PART NO. DESCRIPTION SPACER INCLUDES O-RING

71597-AA 90 ELBOW NOW3770-4

71597-AAS 90 ELBOW WITH SPACER YES

80827-1AA TEE W3770-4

3026 ofPageDPL82088

13.250336.55

26.500in673.10mm

CL FRONT DISCHARGE MANIFOLD

CL OF CHASSIS

CL MAIN PUMPSIDE DISCHARGE

.C.2.500in

63.50mmBOTH ENDS TYP

8X .467in.476in

11.8612.08 THRU

EQUALLY SPACED ON 4.375/111.13 B.C.BOTH ENDS TYP

3.72694.64

NON A.C.

4.033102.44

.1112.82

NON A.C.

.42110.69A.C.

CL FRONT DISCHARGE MANIFOLD

CL MAIN PUMP SIDE DISCHARGE

TYPE 25 - FITTINGS FOR 3-1/2 IN. FRONT DISCHARGE ON CM/CS PUMPS

MANIFOLD

82551 FRONT DISCHARGE MANIFOLD

3027 ofPageDPL82088

8X .531in13.49mm

11.536in293.01mm

12.500in317.50mm

.500in12.70mm

.875in22.23mm 1.125in

28.58mm

6.0 IN. NH

11.536in293.01mm

12.500in317.50mm

8X .531in13.49mm

10.563in268.29mm

2.500in63.50mm

3.094in78.59mm

4X 7/16-14 UNC-2BEQUALLY SPACED ON

4.375/11.13 B.C.

SPECIFY TYPE 19 FITTING IF NECESSARY

.500in12.70mm 4.000in

101.60mm

.875in22.23mm

1.125in28.58mm

6.0 IN. NH

NOTES:ALL FITTINGS INCLUDE GASKET AND MOUNTING HARDWARE.1.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.2.

TYPE 30 - FITTINGS FOR OVERSIZED PANT LEG INTAKE FITTING 82952

THREADED NIPPLES

(USE WITH FLANGED SECTION 2 INTAKE FITTINGS ON DPL81867)

8 IN. JAMESBURY BUTTERFLY VALVESEE DRAWING DPL83723

NIPPLE WITHOUT DUMP VALVE FLANGE NIPPLE WITH DUMP VALVE FLANGE

NIPPLE PART NO.A INCLUDES

82957-A SEE TYPE 31 FITTINGS

6.500/165.10910903

83263-A 4.000/101.60

NIPPLE PART NO. INCLUDES GASKETMOUNTED ON BUTTERFLY VALVE

NO YES82953-A SEE TYPE 31

FITTINGS 910903

3028 ofPageDPL82088

4 X .406in10.32mm

EQUALLY SPACED ON5.375/136.53 B.C.

5.875in149.23mm

.500in12.70mm

4.125in104.78mm

4 X .408in10.36mm

RADIAL SLOTSSPACED ON 5.375/136.53 B.C.

4.875in123.83mm

2.500in63.50mm

4X 17°

4X .50012.70

4.250in107.95mm

2.500in63.50mm

NOTES:ALL FITTINGS INCLUDE GASKET AND MOUNTING HARDWARE.1.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.2.SPECIFY WHERE EACH FITTING IS TO BE MOUNTED.3.

TYPE 36 - FITTINGS FOR 2-1/2 IN. AKRON/ELKHART 4-BOLT MACHINED PADS

ELBOW FLANGE

71443-2A 90 MEDIUM ELBOW 51218

3029 ofPageDPL82088

2.000in50.80mm

1.200/30.48 B.C.

6.125/155.58 B.C.

7.000in177.80mm

.656in16.67mm

NOTES:ALL FITTINGS INCLUDE GASKET AND MOUNTING HARDWARE.1.ALL DIMENSIONS SHOWN AS INCH/MILLIMETER.2.SPECIFY WHERE EACH FITTING IS TO BE MOUNTED.3.

TYPE 70 - FITTINGS FOR ADVANTUS CONDUCTIVITY PROBE TAP

TYPE 71 - FITTINGS FOR 3 IN. UNI-BODY (AKRON/ELKHART) 4-BOLT MACHINED PADS

FLANGE

53072-A PLUG W3710-2

3030 ofPageDPL82088

Auxiliary Fittings Dimensional Drawings · 2018-12-13 · Auxiliary Fittings Dimensional Drawings...

Documents

Transcript of Auxiliary Fittings Dimensional Drawings · 2018-12-13 · Auxiliary Fittings Dimensional Drawings...

Track, Wheel and Engineering Data and · PDF fileDeerfield and Roundabout Railway Track, Wheel and Engineering Data and Drawings ... AUXILIARY - Spring washers, tie plates, rail braces

Study Unit Auxiliary Views To give you the earliest as ...€¦ · 28.10.2013 · auxiliary view presentation can be found in the document . Multi and Sectional View Drawings (ANSI

EML 2023 – Modeling, Drawings Lecture 2.3 - Auxiliary and Section Views.

Auxiliary Bicycles Act 1954 - Bermuda Laws Laws/Auxiliary Bicycles Act... · AUXILIARY BICYCLES ACT 1954 Auxiliary bicycle register Identification numbers Use of unregistered auxiliary

[PPT]Auxiliary Drawings - King William County Public Schools · Web viewTitle Auxiliary Drawings Author quimby Last modified by KWCPS Created Date 1/8/2004 5:40:59 PM Document presentation

NASA€¦ · Web view2000. 8. 23. · all construction contracts exceeding $2,000. ... Drawings of such objects as fasteners, nuts, bolts, wires, screws, nails, pipe fittings, brackets,

Assessment Requirements for MARL031 Demonstrate · PDF fileand maintenance of marine auxiliary machines, including machinery specifications, machinery design drawings, machine drawings,

DESIGN DRAWINGS VENDOR DRAWINGS

· Intro to Plumbing Tools and Drawings/ Plastic and Copper Pipe and Fittings CT T F 153 Plumbing Piping and Tools ... of instructor. 7.

Brass Fittings Copper Fittings India

Raccordi standard Standard fittings - RECTUS · 136 Foto, disegni e dati tecnici non impegnativi Pictures, drawings and technical data not binding Raccordi standard Standard fittings

Activity X Title - Long Branch Public Schools€¦ · Web viewGenerate CAD multi-view technical drawings, including orthographic projections, sections view(s), detail view(s), auxiliary

Pneumatic fittings, air fittings, push in fittings

Pneumatic fittings, air fittings, push to connect fittings, push in fittings, air line fittings

Mechanical Engineering (ME) - Stanford University · including orthographic projection, dimensioning, sectioning, exploded and auxiliary views, assembly drawings, and SolidWorks.

Syntax: Auxiliary verbs LING 400 Winter 2010. Overview VP substitution (review) VP substitution (review) Auxiliary verbs Auxiliary verbs Properties Auxiliary.

Working with your Architect - arbv.vic.gov.au · selection of materials, fittings etc and associated cost. Contract documentationproduces technical drawings and specifications to

piping and fittings fittings

Working Drawings (Production Drawings)

Commercial Drawings - PHCC Of Georgia - …plumbingpros.com/pdf/commercialdraw.pdf · Commercial Drawings The Different Drawing Groups C-drawings A-drawings S-drawings M-drawings