Post on 22-Jul-2020
Product Description Au.diPanel offers our widest selection of perforation options and a choice of substrates. Combined with our range of decorative surface finishes and our Integrated Acoustic Backing (IAB), Au.diPanel lends itself to tailoring for specific appearance or acoustic performance requirements.
Product Features– Standard range of pre-finished timber grain and
decorative surfaces– Largest selection of perforation patterns– Panel sizes up to 3600 x 1200mm – Veneers can be nominated to co-ordinate with
other timber building elements or furnishings– Higher impact-resistance obtained with
plywood panels
Variations – Optional face veneer to your specifications– Range of standard perforation patterns or custom
patterns – Range of standard side and end margins or custom
margins – Edge profiling and face detailing of panels
available to specification– Integrated Acoustic Backing (IAB)– Graphic images achievable
Jointing Options– Vee Joint– Expressed Joint
(Where expressed joints are selected, allowance should be made for dressing of panel edges)
Material Sizes Au.diPanel is available uncoated or pre-finished in our select range of decorative surface finishes in the following sizes. For non-standard sizes, consult Atkar Technical Staff.
Natural timber veneers in lengths over 2400mm are limited and subject to current availability.
Performance AcousticDiversity of perforation options allow for open area of panel to range from 2.47% up to 34.51 % nominally.
Open Area Guide
Au.diPanel data sheet
© Copyright 2018 GroupAtkar
TM
WA/SAPOT 5662 6323 08
6919 DC Joondalup 710 Box Region Head Office
17–19 David Lee Road Hallam Victoria 3803 PO Box 1143 Narre Warren MDC 3805 T 03 9796 3333 atkar.com.au
with Graphic Au.diPanel
ApplicationsWalls ceilings and
Substrates–––––– OSB
Plywood resistant moisture MDF
rated fire Blackcore / Blackcore MDF rated fire MDF standard MDF
FireFor Atkar. contact please ratings fire Number Group
Rating
WarrantyAu.diPanel
terms. for document warranty to Refer years. (15) fifteen for warranted is
Fixing–––– fix Face
(ceilings) fix concealed PS3 Au.diMount (walls) fix concealed XJ1 Au.diMount (walls) fix concealed BJ2 Au.diMount
Systems
NRC 0.8 to up value
Finish
– Inluxe– Inluxe– Inluxe– Inluxe Colour
Laminate Image Veneer
Options
Document 3 Version
Margin Options Standard
possible. sizes margin Other 25mm. is margin perimeter
Perforation Patterns Available
patterns
MDF
12.0mm. and 10.0mm 8.0mm, 6.0mm, :sizes perforation following
the for used be can substrate rated fire
Staff. Technical Atkarconsult sizes, perforation and patterns
custom For below. detailed as of selection a in diameter 57.0mm to 4.5mm from ranging sizes perforation with
Au. Paneldi data sheet
© Copyright 2018 GroupAtkar
Product AP125S Type Product AP125D Type
Product AP250S Type Product AP250D Type
Product AP500S Type Product AP1000S Type
Document 3 Version
Accesseasily
shouldtheplanks
machined
Standard
request. on available sizes Custom 600mm. x 600 450mm, x 450 sizes: panel access
to. mounted be to services for installed insert matching solid custom a and
left be can space width plank 3 or 2 a Alternatively installed. they’re once the into cut be
can penetrations Service planks. of installation the during on-site out carried be processes
These Au.diPanel. intointegrated be can penetrations ceiling other and panels
Access Panels
Vee Joint* Timber Batten or Stud
Expressed Joint Timber Batten or Stud
Bevel Panel Edges
Acoustic Insulation(optional)
Integrated AcousticBacking or selectedscrim shown dotted
*Vee jointing may create difficulties with panel and perforation alignment
Au.diPanel
Acoustic Insulation(optional)
Integrated AcousticBacking or selectedscrim shown dotted Au.diPanel
BackingStrip
Attention – The method of fixing indicated for this product is of a general nature only and does not allow for specific design criteria such as wind loads, expansion joints or any other special design requirements which should be separately provided for by the It
secured. firmly are panels ensure to responsibility installers the is
specifier.
Due to continual product improvement the information in this publication is subject to alteration without notice.
Jointing Details
* For other thicknesses consult Atkar Technical Staff.
used. be to fixings discrete more enable to recommended are members To
framing
minimise the risk of buckling, it is recommended that the panels be allowed to acclimatise in the area in which they are to be installed. This is best achieved by standing individual panels loosely around the room and allowing air to freely circulate around them for several days prior to fixing. Allowance should be made between panels to accommodate swelling and building movement.
Au.diPanel installation guide
© Copyright 2018 GroupAtkar
Au.diStyle Au.diStyle Au.diStyle Au.diStylePanelAu.di
Wall frame Batten or Stud Batten or Stud Batten or StudWall frame
Edge profile/finish as selectedEdge profile/finish as selectedExposed fasteners as selected
Exposed fasteners as selectedBevel panel edges
Edge profile/finish as selectedMax. joint width
5
Expressed Joint – Plan view Au.diMount Concealed Fixing System (Refer to Installation System - XJ1)
Butt Joint System Typical detail refer to Au.diMount BJ2 System for full details
Wall Frame
AMCC061screwed to wall frame
AMCO61screwed to rear of panel
Panel
Panel
Panel
Panel
4
3
2
5
1
Installation Details The following table provides a fixing guide for general residential and commercial applications. Panels can be face fixed or conceal fixed. Refer to Au.diMount data sheets for applicable concealed fixing systems.
Consideration should be given to reduced framing centres for higher impact areas such as corridors and crowded spaces, or where surfaces are to be curved. Au.diPanel wall panels should be installed with a full perimeter support and plywood ceiling panels must have the face grain running at right
timber fixed, face be to are panels If members. framing to angles
Concealed Fixings Expressed Joint Typical detail refer to Au.diMount
XJ1 System for full details
A
advice. further for engineer
acoustican consult Please performance. acoustic optimal
achieve to recommended is gap air 90mm
FaceConcealed
available. options for Atkar Consult required. as head screw
ixF
Document 3 Version
General fixing details. full for Atkar consult applications, interior for only, guide
Typical System details full for PS3 Au.diMount to refer detail