Post on 19-Jul-2020
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 1 of 13
INSTALLATIONINSTRUCTIONS
Accessory Application Publications No.
Issue Date
DEC 2002
2003 ELEMENTFOG LIGHTS
PARTS LIST
Fog Light Kit (sold separately)P/N 08V31-SCV-100
2 Fog lights
Switch harness
Fog light harness
Relay
Fuse label
20 Wire ties
13 Wire ties with clip
8 Self-tapping screws
Fog Light Switch Kit (sold separately)P/N 08V31-SCV-110A (black)P/N 08V31-SCV-120A (gray)
Switch
TOOL AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriverRatchet10 mm socketFileDrill3 mm and 20 mm Drill bitsUtility knifeDiagonal cuttersPushpinHacksaw blade
Clip remover
08V31-SCV-1000-91
2422021K
SWITCHHARNESS
SWITCH
RELAY
FOG LIGHT
FOG LIGHTHARNESS
FOGLIGHT
FUSECASE(20A)
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These procedures shouldnot be attempted by “do-it-yourselfers.”
NOTE: This installation instruction shows the left foglight being installed; the same procedure applies toinstalling the right fog light.
1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.
2. Disconnect the negative cable from the battery.
AII 24288
Illustration of the Fog Lights Installed on the Vehicle
2 of 13 AII 24288 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Fog Light
3. Open the hood and remove the radiator cover (fiveclips).
5. Inside the front bumper, locate the three marks onthe fog light housing on the left side. Using apushpin, pierce the bumper at the center of eachmark. While wearing eye protection, drill a 3 mmpilot hole then finish with a 20 mm hole throughthe bumper at the center of each mark.
4. Remove the front bumper (seven clips at the top,six clips and four stepped bolts at the bottom andone self-tapping screw on each side).
6. While being careful not to scratch the bumper, usea hacksaw blade to cut out the marked area fromthe front bumper along the inside of the scribedline and the groove on the back. Remove all burrsfrom the edges of the cutout.
2328091K
CLIP
RADIATORCOVER
2328101K
CLIPS (7)
FRONTBUMPER
SELF-TAPPINGSCREWS (2)
STEPPEDBOLTS (4)
CLIPS(6)
2329011K
FRONTBUMPER
PUSHPIN
DRILL BITS(First drillwith a 3 mmbit, andfinish with a20 mm bit).
MARKS (3)
FOG LIGHTHOUSING
2329023K
Cut out.SCRIBED LINE
FRONTBUMPERGROOVE
SECTIONAL VIEW
Cut out.
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 3 of 13
7. Inside the front bumper, slide the fog light into thecutout you made, and secure it with four self-tapping screws.
10. Locate the 1-pin connector blue-taped to thevehicle harness and remove the blue tape to freethe 1-pin connector. Connect the 1-pin connectoryou just freed to the fog light harness 1-pinconnector .
11. Loosen the ground bolt that fastens the vehicleground terminal and secure the fog light harnessground terminal using this ground bolt.
12. Secure the fog light harness 1-pin connector andthe fog light harness to the vehicle harness withone wire tie. Do not secure the 1-pin connector tothe SRS harness with the wire tie.
2403021K
FOG LIGHTHARNESS
FOG LIGHT HARNESSGROUND TERMINAL
GROUNDBOLT
2402011K
WIRE TIE
FOG LIGHTHARNESS 1-PINCONNECTOR
FOG LIGHTHARNESS
SRSHARNESS
Routing the Fog Light Harness
9. Starting under the left headlight, route the fog lightharness 1-pin connector and ground terminalthrough the hole in the front bulkhead.
8. Repeat steps 5 thru 7 to cut the bumper andinstall the fog light on the right side of the bumper.
2329030K
FOG LIGHT
FRONTBUMPER
SELF-TAPPINGSCREWS (4)
2403010K
BLUETAPE
FOG LIGHTHARNESS1-PINCONNECTOR
FOG LIGHTHARNESSGROUNDTERMINAL
VEHICLE 1-PINCONNECTOR
LEFT FRONTBULKHEADPANEL
FOG LIGHTHARNESS
4 of 13 AII 24288 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
2417070K
2418010K
2409050K
2403030K
13. Behind the front side frame, route the fog lightharness 2-pin connector (short end) down, and outthrough the clearance between the side frame andfront bumper beam. Attach the wire tie with clip tothe fog light harness at the green tape, then pushthe clip into the hole in the side frame.
14. Route the fog light harness 2-pin connector (longend) up along the bulkhead side stay, then alongthe vehicle harness behind the front bulkheadupper frame.
15. Continue routing the fog light harness 2-pinconnector forward, then down to the bottom of thefront side frame along the outside of the rightbulkhead side stay.
16. Align the green tape on the fog light harness(closest to the connector) with the hole in the frontlower cross member, then secure the harness tothe hole with the wire tie in the area shown.
LEFT FRONTSIDE FRAME
GREENTAPEWIRE TIE
WITH CLIPFOG LIGHTHARNESS 2-PINCONNECTOR(SHORT END)
FRONT BUMPERBEAM
FRONT BULKHEADUPPER FRAME
VEHICLEHARNESS
FOG LIGHTHARNESS
FOG LIGHTHARNESS
RIGHTBULKHEADSIDE STAY
FOG LIGHTHARNESS 2-PINCONNECTOR
FRONT SIDEFRAME
FOG LIGHTHARNESS
FOG LIGHTHARNESS
WIRE TIE
FRONT LOWERCROSS MEMBER
GREENTAPE
FRONT BUMPERBEAM
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 5 of 13
17. Attach the three wire ties with clips to the fog lightharness at the green tapes, then push the clipsinto the holes in the bulkhead side stay. Furthersecure the fog light harness to the vehicle harnesswith two wire ties in the areas shown.
If the vehicle is equipped with an engine blockheater:
Secure the engine block heater and fog light harnessesto the bulkhead side stay with the wire ties on theengine block heater harness and two wire ties withclips on the fog light harness.
18. Secure the fog light harness to the vehicleharness with six wire ties in the areas shown.
19. Secure the fog light harness to the holes in thebulkhead side stay and the side frame with fourwire ties with clip.
20. Secure the fog light harness to the front bulkheadarea with the wire tie with clip, and to the vehicleharness with one wire tie.
21. Secure the fog light harness to the hole under thefront side frame with one wire tie with clip.
2418050K
FOGLIGHTHARNESS
WIRE TIEWITH CLIP
WIRE TIE
LEFT FRONTSIDE FRAME
WIRE TIEWITH CLIP
LEFTBULKHEADSIDE STAY
LEFT FRONTBULKHEAD
2418041K
WIRE TIE
WIRE TIE
FOG LIGHTHARNESS
WIRE TIEWITH CLIP
2418022K
WIRE TIE
FOG LIGHTHARNESS
WIRE TIEWITH CLIP (3)
GREENTAPE
FOG LIGHTHARNESS
RIGHTBULKHEADSIDE STAY
2418031K
FOG LIGHTHARNESS
WIRE TIE WITH CLIPON FOG LIGHT HARNESS
ENGINE BLOCKHEATER HARNESS
WIRE TIE ONENGINE BLOCKHEATER
RIGHTBULKHEADSIDE STAY
6 of 13 AII 24288 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
22. While holding the front bumper near the front ofthe vehicle, plug the fog light harness 2-pinconnectors into the 2-pin connectors from the foglights. Reinstall the front bumper.
24. Remove the center dashboard lower cover (twoexpansion clips, two clips and four retaining tabs).
NOTE: This illustration shows the center lower coverwith subwoofer. Remove the center lower cover withoutsubwoofer the same way.
Routing the Switch Harness
23. Remove the driver’s dashboard lower cover, turnthe knobs clockwise, then pull the cover outtoward you to release the six retaining tabs.
2418061K
FOG LIGHT2-PINCONNECTOR
FOG LIGHTHARNESS2-PINCONNECTOR
FOG LIGHTFRONT BUMPER
FOG LIGHT
FOG LIGHTHARNESS2-PINCONNECTOR
2403050K
RETAININGTABS (6)
KNOB
DRIVER’SDASHBOARDLOWERCOVER
2403062K
RETAININGTABS (4)
EXPANSIONCLIPS (2)
CENTERDASHBOARDLOWER COVER
CLIPS (2)
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 7 of 13
25. Starting from behind the instrument panel, routethe switch harness 8-pin connectors down alongthe vehicle harness. On the left of the instrumentpanel frame, unplug the vehicle 8-pin connectors(gray), and plug the switch harness 8-pinconnectors in between the switch harnessconnectors and the vehicle connector.
26. Slide the switch harness 8-pin connector onto theholder on the vehicle 8-pin connector (gray).
27. Locate the 1-pin connector blue-taped to thevehicle harness and remove the blue tape to freethe connector. Plug the vehicle harness 1-pinconnector into the switch harness 1-pin connector(blue/red).
28. At the fuse box, plug the switch harness1-pin connector (white/red) into the fuse box in thelocation shown.
2404011K
SWITCHHARNESS
SWITCHHARNESS 8-PINCONNECTOR
VEHICLE 8-PINCONNECTOR(GRAY)
HOLDER
2403072K
VEHICLE 8-PINCONNECTOR(GRAY)
INSTRUMENTPANEL FRAME
VEHICLECONNECTOR(Cruisecontrolsystemequippedonly.)
INSTRUMENTPANEL
SWITCHHARNESS
2404022K
SWITCH HARNESS1-PIN CONNECTOR(BLUE/RED)
VEHICLEHARNESS BLUE TAPE
VEHICLE 1-PINCONNECTOR
SWITCHHARNESS
2405010K
FUSE BOX
SWITCHHARNESS 1-PINCONNECTOR(WHITE/RED)
SWITCHHARNESS
1-PIN CONNECTORCONNECTING PORT
SWITCHHARNESS 8-PINCONNECTOR
8 of 13 AII 24288 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
30. On M/T only: Plug the switch harness 6-pinconnector into the fuse box.
29. On A/T only: Unplug the vehicle 6-pin connectorfrom the fuse box. Remove and discard thedummy connector from the 6-pin connector black-taped to the switch harness. Plug the switchharness 6-pin connectors in between the fuse boxand the vehicle connector.
31. Unplug the vehicle 12-pin connector from the fusebox and plug the switch harness 12-pinconnectors in between the fuse box and thevehicle connector.
32. Attach the fuse label (20A) to the fuse case on theswitch harness.
33. From under the steering shaft, route the switchharness 5-pin connector to the left from behind theknee bolster.
34. Remove the switch cover from the instrumentpanel, and pull the switch harness 5-pin connectorout through the hole.
2405021K
SWITCH HARNESS6-PIN CONNECTOR
VEHICLE 6-PINCONNECTOR(A/T only)
SWITCH HARNESS6-PINCONNECTOR
FUSE BOX 6-PINCONNECTOR PORT
DUMMYCONNECTOR(Discard.)
FUSEBOX
SWITCHHARNESS
2405031K
FUSEBOX
SWITCH HARNESS6-PINCONNECTOR
SWITCHHARNESS
2405051K
SWITCHHARNESS5-PINCONNECTOR
SWITCHCOVER(Discard.)
SWITCHHARNESS
STEERINGSHAFT
KNEEBOLSTER
FUSECASE ONSWITCHHARNESS
FUSELABEL(20A)
2405041K
SWITCHHARNESS12-PINCONNECTOR
VEHICLE 12-PINCONNECTOR
SWITCHHARNESS
FUSE BOX 12-PINCONNECTOR PORT
FUSEBOX
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 9 of 13
36. Align the green tape on the switch harness withthe vehicle harness clip, then secure the switchharness to the vehicle harness with the three wireties in the areas shown.
NOTE: If the vehicle is not equipped with a cruisecontrol switch, attach the wire tie with clip to theswitch harness. Push the switch harness clip fromthe wire tie with clip into the hole in the instrumentbracket.
35. Plug the relay into the switch harness relay block,then slide the relay block onto the instrumentpanel bracket stay.
37. Attach a wire tie with clip to the switch harness atthe green tape, then push the clip into the hole inthe steering hanger lower bracket.
38. Secure the switch harness to the vehicle harnessand to the hole in the steering hanger lowerbracket with two wire ties and one wire tie withclip. Move the steering wheel up and down toconfirm that the switch harness is not beingpulled. Readjust if necessary.
2409011K
WIRE TIEWITH CLIP
SWITCHHARNESS
VEHICLECLIP
GREENTAPE
WIRETIE
WIRETIE
SWITCHHARNESS
INSTRUMENTPANELBRACKET
WIRE TIE
With cruisecontrol switch
Without cruisecontrol switch
2408011K
SWITCHHARNESS
SWITCHHARNESSRELAYBLOCK
RELAY
INSTRUMENT PANELBRACKET STAY
2409022K
SWITCHHARNESS
WIRE TIEWITH CLIP
WIRETIE
STEERINGHANGERLOWERBRACKET
GREENTAPE
WIRETIEWITHCLIP
WIRETIE
SWITCHHARNESS
10 of 13 AII 24288 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
40. Plug the switch harness 5-pin connector (blue) intothe switch, then install the switch in the hole in theinstrument panel.
41. Check that all wire harnesses are routed properlyand all connectors are plugged in.
42. Reinstall all removed parts. Check that all clipsand fasteners are installed securely.
43. Reconnect the negative cable to the battery.
44. Reset the clock, and reset the radio stationpresets.
NOTE: Whenever the battery is disconnected, thedriver’s window AUTO function is disabled.
45. Start the engine. Push down on the driver’swindow switch until the window is fully open.
46. Pull up on the driver’s window switch to close thewindow completely, then hold the switch for2 seconds.
47. Lower and raise the window to check the operationof the driver’s window AUTO function.
USE AND CARE
How to Operate Fog Lights
• Turn the light switch to the “ ” position(headlights on low beam).
• Press the fog light switch (indicator is on).
The fog light lenses can cloud when the outsidetemperature is cold; this is a normal condition.
39. Secure the switch harness to the vehicle harnesswith two wire ties in the areas shown.
2409031K
WIRETIE
SWITCHHARNESS
2409040K
INSTRUMENTPANEL
SWITCH
SWITCHHARNESS 5-PINCONNECTOR(BLUE)
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 11 of 13
Replacing the Fog Light Bulb
1. Loosen the upper right screw on the fog light. Liftthe fog light up, then pull it out toward you.
2. Remove the fog light connectors from the bracketstay, then unplug the connectors. Remove the foglight.
3. Remove the fog light rear cover (five screws).
Fog Light Aiming Adjustment
• Adjust the aiming according to local laws andregulations.
• To adjust, turn the aiming adjustment screw in orout until the correct aiming is obtained.
2419010K
BRACKETSTAY
CONNECTORFOG LIGHT
2419030K
SCREWS (5)
REARCOVER
FOG LIGHT
2418070K
To raise
To lower
PHILLIPSSCREWDRIVER
AIMING ADJUSTMENTSCREW
2419020K
FOG LIGHTAIMINGADJUSTMENTSCREW UPPER RIGHT
SCREW (Loosen.)
FOG LIGHT
HOOK
12 of 13 AII 24288 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
5. Install the new bulb into the socket.
• Use only a genuine Honda halogen light bulb ofspecified wattage.
Rating: 12V 55W H3 Halogen Light BulbP/N 33165-SB0-7310-M1
• Do not touch the bulb. Oily or greasysubstances on the bulb can shorten its servicelife due to the heat produced when the bulb isturned on. If the bulb is accidentally touched,wipe it clean with a soft cloth that has beendampened with denatured alcohol or a milddetergent solution.
• Align the tab on the fog light with the cutoutwhen installing the new bulb. If it is not aligned,the fog light may annoy oncoming drivers.
6. Reinstall the removed parts in the reverse order ofremoval.
• Check that the wire harnesses are not pinched.
• Make sure to tighten the screws securely.
4. Remove the retainer spring, and pull out the bulband socket as a unit.
BULB
RETAINERSPRING
HOOK
CUTOUT
NEW BULB
TAB
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 13 of 13
OFF
LIGHT SWITCH
OFFLow Hi
OFF
ON ON
FO
G L
IGH
TS
WIT
CH
BLK
YEL
BLU
GRN
RED
WHT
BLACK
YELLOW
BLUE
GREEN
RED
WHITE
BROWN
ORANGE
LIGHT BLUE
LIGHT GREEN
PINK
GRAY
BRN
ORN
LT BLU
LT GRN
PNK
GRY
HOT ATALL TIMES
HOT WITHHEADLIGHTSWITCH INHEAD HOT WITH
HEADLIGHT SWITCHIN PARK OR HEAD
FRONT FOGLIGHT
20A
RED/YELFog LightFuse WHT
RED/BLK
RED/BLURED
IlluminationControl
RED/WHT
Fog LightRelay
BLU/RED
FrontFogLights
BLK
1 2DimmerSwitch1: Low2: High
1 2
Switch1 = Switch
Illumination2 = Indicator
WHT/RED
CIRCUIT DIAGRAM