A-dec 300 Dual Mount on 500

Post on 24-Feb-2016

32 views 0 download

Tags:

description

A-dec 300 Dual Mount on 500. Installation. Agenda. General Information Recommended tools Installation Follow through install guide Hands-on install Adjustments Leveling. Learning Objectives. As a result of this training you will be able to: - PowerPoint PPT Presentation

Transcript of A-dec 300 Dual Mount on 500

A-dec 300 Dual Mount on 500Installation

Agenda► General Information

► Recommended tools► Installation

► Follow through install guide► Hands-on install► Adjustments► Leveling

Learning Objectives► As a result of this training you will be able

to:► Identify the different components and options of

an A-dec 300 dual mount system on a 511 chair► Complete a full installation► Demonstrate how to use the installation guide► Make adjustments and level

Tools► Recommended Tools:

► Sizes are all SAE, no metric► Hex Key Set (inch)► Phillips & standard screw

drivers► Socket wrench set (SAE)► Snap ring tool► Adjustable wrench► Needle nose pliers► Combination wrench set (SAE)► Standard pliers► Diagonal cutters► Torpedo Level

511 Chair Box 1► Chair and Footswitch ► Move the chair from

the pallet

A-dec 511 Chair Installation► Plug in the

chair and turn on

► Use the three-tap feature to raise the chair

► Remove the shipping pin

A-dec 511 Chair Installation► Anchor the chair to the floor

Anchor the ChairTo Concrete► Drill a 4” (101 mm) deep hole. Drill

through the chair anchoring hole into the concrete. Use a roto-hammer drill.

► Remove any debris► Drive the anchor bolt into the hole

until the bolt head seats against the chair base.

► Tighten the bolt until it is tight against the washer and firmly holds the baseplate to the floor.

To Wood► Drill a 2” (50 mm) deep hole. Use a 3/8”

(0.375 mm) drill.► Remove any debris► Place the washer on the anchor bolt and

insert it into the hole.► Tighten the anchor bolt until it is tight

against the washer and firmly holds the baseplate to the floor.

Install the Footswitch► Footswitch is optional. If the chair was

ordered with a footswitch, install it next.

A-dec 511 Chair Installation► Install the back support and headrest

300 Dual mount Installation

300 Dual Mount Installation► Lower the back► Install the front mount Screw the leveling bolts

(from the kit) into the chair frame, leaving two threads exposed

300 Dual mount Installation► Hang the front mount on the leveling cam

300 Dual Mount Installation► Screw the nuts on the leveling bolts until

they are finger tight

Install the Rigid Arms

Delivery System

Dual Rigid Arms

Dental Light or Monitor Mount

Delivery System Only21

Dental Light or Monitor Mount Only1

Installing the Rigid Arms► Tighten the nut until the arm can move

smoothly but is not loose and does not drift

Installing Dual Rigid Arms► Install the spacer Place the spacer with its

solid side up and its opening toward the hydraulic tubing

Installing Dual Rigid Arms► Install the toeboard ramps

Installing Dual Rigid Arms1 2

Level the Rigid Arms

Leveling the Rigid Arms

Leveling Bolts

Leveling► Fully raise the chair back

Place level so it is side to side on the mount

Leveling

LevelingTighten the nuts on the leveling bolts on both sides of the front mount

Tighten the stabilizing bolts on each side of the mount until they touch the chair casting

Delivery InstallationA-dec 332 Radius-Style Traditional Delivery System on an A-dec 511 chair

A-dec 333 Radius-Style Continental Delivery System on an A-dec 511 chair

Delivery Installation► Install the water bottle

Delivery Installation► Install the flexarm and control head

Delivery Installation► Control head

1. Loosen the button head screw

2. Rotate the control head so it is positioned over the hole for the missing leveling screw

3. Install and tighten 1/4 – 20 x ½” leveling screw

4. Install the 3/8” setscrew

Continental Delivery► Insert whip hooks

Delivery Installation► Route tubing and wiring

Umbilical Wrap

Delivery Installation► Route the tubing and wiring

Remove the tape from the tubing

Continental Tray Holder► Optional

Traditional Tray Holder► Optional

Dental Light1. Fully lower the chair base2. Lubricate the end of the

upper rigid arm3. Route the light cable through

the lower rigid arm4. Insert the upper rigid arm

into the lower rigid arm until fully seated

Installation is identical for the A-dec 372 or A-dec 572 Dental Light.The A-dec 372 is shown here.

Dental Light

Install the umbilical wrap

Route the cable

Monitor Mount

Install the rotation stop screw and spacer

Route the power and video cables through the mount and down through the rigid arm

Slide the monitor mount onto the rigid arm

Monitor Mount► Install protective sheath over the monitor

cables and secure with cable tie

Monitor Mount► Install the umbilical wrap and route the

cables

Umbilical wrap

Route the cables

Monitor Mount► Optional

If the system includes a 100mm VESA standard monitor mounting pattern, use the four screws and nuts to install the adaptor plate

Connections► Connect the electrical wires and data lines

Connect the ground wire

Connect the black wire to 0 VAC and the gray wire to 24 VAC

Plug in the red connector

Secure the wiring to the bail with cable ties

Connections► Tubing

Secure Tubing and Install Water Bottle

Adjustments► Adjust delivery system spring assisted

flexarm

Adjustments► Install the delivery system flexarm rotation

stop screw

Adjustments► Adjust the control head rotation tension

To increase tension, turn the key clockwise.To decrease tension, turn the key counterclockwise.

Adjustments► Adjust the tray rotation tension (Traditional)

Adjustments► Adjust the tray rotation tension (Continental)

Adjustments► Adjust the handpieces1. Remove the back cover2. Turn the air coolant, water coolant,

and drive air controls clockwise to turn them all the way down

3. Lift a handpiece from the holder4. Flip the toggle to water5. Step on the foot control6. Adjust the water coolant flow until

there is 2 drops a second7. Step on the foot control8. Adjust the air coolant flow until the

spray is a fine mist (to increase flow turn the key counterclockwise. To decrease the flow turn the key clockwise)

Adjustments► Set the drive air pressure

Adjustments► IOLS

Adjustments

Adjustments► Doctor’s syringe

Adjustments► Continental whip tension

Adjustments► Dental light flexarm counterbalance

572/372

Adjustments► Dental light horizontal rotation372

Adjustments► Dental light vertical rotation

372

Adjustments► Dental light focus

572

Adjustments► Dental light horizontal and diagonal rotation

572

Adjustments► Dental light vertical rotation

572

Adjustments► Adjust the monitor position

Leveling► Level the front

mount► Place the delivery

system and light in working position

► Place the level in line with the chair

Leveling► Level the front

mount► Back the stabilizing

bolts away from the chair frame

► Loosen the nuts on both leveling bolts

► To level the rigid arms front to back, turn the leveling bolts in or out

Leveling► Leveling the front mount

► Fully raise the chair back► Place the level so it is side

to side on the mount► Loosen bolts on the side of

the cam► To level rigid arms side to

side use ¾” combo wrench to rotate the cam

► Tighten the bolts on the side of the cam

Leveling► Leveling the front mount

Tighten the nuts on the leveling bolts on both sides of the front mount

Tighten the stabilizing bolts on each side of the mount until they touch the chair casting

Leveling► Level the delivery system

Leveling► Leveling the delivery system

Adjustment► Flexarm rotation tension

Deluxe Touchpad Features► Programmable

chair positions► X-ray/rinse button► Cupfill/bowl rinse► Auto Light► Electric handpiece

operation► Endodontics

Deluxe Touchpad Setup

Deluxe Touchpad Setup

Knowledge Check► When do you remove the shipping strap?► Should you move the chair by the armrests?► How do you raise the chair base up prior to

installing a footswitch?► What prevents the chair from crushing the

pump cover?► What position should the delivery head be in

while leveling?► How do you get into the deluxe touchpad

setup mode?

Summary► Tools► Unpacking► Mounting the rigid arms and leveling► Installing the dual mounts► Re-leveling► Adjustments► Deluxe touchpad

Questions?