Post on 28-Dec-2015
9-1
Design of UAV Systems
Communicationsc 2003 LM Corporation
Lesson objective - to discuss
UAV Communicationsincluding …
• RF Basics• Communications Issues• Sizing
Expectations - You will understand the basic issues associated with UAV communications and know how to define (size) a system to meet overall communication requirements
9-1a
Design of UAV Systems
Communicationsc 2003 LM Corporation
Schedule revision
Week 4• Sortie rate estimates• Requirements analysis
Week 5 • Communication considerations and sizing
Week 6• Control station considerations and sizing • Payload (EO/IR and radar) considerations and sizing
Week 7 • Reliability, maintenance, safety and support • Life cycle cost
Week 8• Mid term presentations
9-2
Design of UAV Systems
Communicationsc 2003 LM Corporation
Importance
• Communications are a key element of the overall UAV system
• A UAV system cannot operate without secure and reliable communications
- unless it operates totally autonomously
- Only a few (generally older) UAVs operate this way
• A good definition (and understanding) of communications requirements is one of the most important products of the UAV concept design phase
9-3
Design of UAV Systems
Communicationsc 2003 LM Corporation
• RF basics• Data link types• Frequency bands• Antennae• Equations
• Communications issues• Architecture• Function• Coverage• Etc.
• Sizing (air and ground)• Range • Weight• Volume• Power
• Example problem
Discussion subjects
9-4
Design of UAV Systems
Communicationsc 2003 LM Corporation
Data link types
• Simplex - One way point-to-point• Half duplex - Two way, sequential Tx/Rx• Full duplex - Two way, continuous Tx/Rx• Modem - Device that sends data sent over analog link• Omni directional - Theoretically a transmission in all directions (4 steradian or antenna gain 0) but generally means 360 degree azimuth coverage
• Directional - Transmitted energy focused in one direction (receive antennae usually also directional)- The more focused the antennae, the higher the gain
• Up links - used to control the UAV and sensors• Down links - carry information from the UAV (location, status, etc) and the on-board sensors
9-5
Design of UAV Systems
Communicationsc 2003 LM Corporation
Frequency bands
Civil Radio band designation1-10 kHz VLF (very low frequency)10-100 kHz LF (low frequency)100-1000 kHz MF (medium frequency)1-10 MHz HF (high frequency)10-100 MHz VHF (very high frequency)100-1000 MHz UHF (ultra high frequency)1-10 GHz SHF (super high frequency)10-100 GHz EHF(extremely high frequency)
Satellite band designationS Band 1700-3000 MHzC Band 3700-4200 MHzKu1 Band 10.9-11.75 GHzKu2 Band 11.75-12.5 GHz Ku3 Band 12.5-12.75 GHzKa Band 18.0-20.0 GHz
US Military and Radar bands1-2 GHz L Band2-4 GHz S Band4-8 GHz C Band8-12 GHz X Band12-18 GHz Ku Band18-27 GHz K Band27-40 GHz Ka Band40-75 GHz V Band75-110 GHz W Band110-300 GHz mm Band300-3000 GHz mm Band
Note - NATO designations cover almost the same frequency ranges
NATOD BandE/F BandG/H BandI BandJ BandK BandK BandL BandM Band
9-6
Design of UAV Systems
Communicationsc 2003 LM Corporation
UAV frequencies
Military and civilian UAVs communicate over a range of frequencies • An informal survey of over 40 UAVs (mostly military, a few civilian) from Janes UAVs and Targets shows:
Up linksBand % usingVHF (RC) 13% UHF 32%D 6%E/F 11%G/H 21%J 15%Ku 2%
Down linksBand % usingVHF 0%UHF 17%D 19%E/F 13%G/H 23%J 17%Ku 9%
Higher frequency down links provide more bandwidth
9-7
Design of UAV Systems
Communicationsc 2003 LM Corporation
More basics
• Carrier frequency
- The center frequency around which a message is sent- The actual communication or message is represented by a modulation (e.g. FM) about the carrier
• Bandwidth
- The amount (bandwidth) of frequency (nominally centered on a carrier frequency) used to transmit a message
- Not all of it is used to communicate - Some amount is needed for interference protection
- Sometimes expressed in bauds or bits per second but this is really the data rate
9-8
Design of UAV Systems
Communicationsc 2003 LM Corporation
Data rate
• How much real data can be sent (bits per second)- A typical voice message uses a few Kbps and can be
transmitted on a single frequency channel- Real time video can require Mbps and must be transmitted across a range of frequencies
- Still images can be sent at low data rates over time• Sometimes described using telecom line notation
- T1 = 1.5 mbps; T3 = 45 mbps, etc• Related to bandwidth
but not directly- Synchronization, error checks and other factors involved- Limited data shows a 70% relationship
Data rate vs. band width
y = 0.69x - 0.03
0
10
20
30
40
50
60
0 20 40 60 80
Band width (MHz)
Global HawkPredatorMany people use band width and data
rate as synonymous term
s. Even th
ough
not rigorously corre
ct, we will
do likewise
9-9
Design of UAV Systems
Communicationsc 2003 LM Corporation
Polarity
• The physical orientation of an RF signal- Typically determined by the design of the antenna- But influenced by ground reflection
• Two types of polarization, linear and circular- Linear polarity is further characterized as horizontal (“h-pole”) or vertical (“v-pole”)- A simple vertical antenna will transmit a vertically polarized signal. The receiving antenna should also be vertical
- V-pole tends to be absorbed by the earth and has poor ground reflection (tracking radars are V-pole).
- H-pole has good ground reflection which extends the effective range ( used for acquisition radars)
- Circular polarity typically comes from a spiral antenna- EHF SatCom transmissions are usually circular- Polarization can be either right or left hand circular
9-10
Design of UAV Systems
Communicationsc 2003 LM Corporation
And more
• Antenna gain - a measure of antenna performance
- Typically defined in dBi = 10*log10(P/Pi)- where P/Pi = ability of an antenna to focus power vs. theoretical isotropic (4 steradian) radiation
- Example - an antenna that focuses 1 watt into a 3deg x 3 deg beam (aka “beam width”) has a gain of
10*Log10(1/3^2/1/360^2) = 41.6 dB
- For many reasons (e.g., bit error rates) high gain antennae (>20dBi) are required for high bandwidth data
Example - 10.5 Kbps Inmarsat Arero-H Antenna
- For small size and simplicity, low gain antenna (< 4 dBi) are used………... for low bandwidth data
Example - 600 bps Inmarsat Aero-L Antenna
9-11
Design of UAV Systems
Communicationsc 2003 LM Corporation
Examples
Antenna Size
0
20
40
60
80
100
120
0 2000 4000 6000 8000 10000Volume (cuin)
Inmarsat I (4.8 Kbps) Weight = 18 lb, 6 dB
Data and pictures from http://www.tecom-ind.com/satcom.htm, weights = antenna + electronics
Inmarsat H (≈9.6 Kbps) Weight = 102 lb, 12 dB
Inmarsat L (600 bps) Weight = 8 lb, ? dB
9-12
Design of UAV Systems
Communicationsc 2003 LM Corporation
More basics - losses
Free space loss
- The loss in signal strength due to range (R)= (/4R)^2
- Example : 10 GHz (=0.03m) at 250 Km = 160.4 dBi
Atmospheric absorption
- Diatomic oxygen and water vapor absorb RF emissions
- Example : 0.01 radian path angle at 250 Km = 2.6 dB
Precipitation absorption
- Rain and snow absorb RF emissions- Example : 80 Km light rain cell at 250 Km = 6.5 dBExamples from “Data Link Basics: The Link Budget”, L3 Communications Systems West
9-13
Design of UAV Systems
Communicationsc 2003 LM Corporation
Architecture
• Military • Commercial• “Common”
Function
• Up link (control)
• Launch and recovery• Enroute• On station• Payload control
• Down link (data)
• Sensor• System status
Communications issues
Coverage
• Local area• Line of sight• Over the horizon
Other issues• Time delay
• Survivability
• Reliability• Redundancy• Probability of
intercept• Logistics
9-14
Design of UAV Systems
Communicationsc 2003 LM Corporation
Military vs. civil
Military communications systems historically were quite different from their civilian counterparts
• With the exception of fixed base (home country infrastructure) installations, military communications systems are designed for operations in remote locations under extreme environmental conditions
• They are designed for transportability and modularity- Most are palletized and come with environmental
shelters
Civilian communications systems were (and generally still are) designed for operation from fixed bases
• Users are expected to provide an environmentally controlled building (temperature and humidity)
Now, however, the situation has changed
9-15
Design of UAV Systems
Communicationsc 2003 LM Corporation
Communication types
Military operators now depend on a mix of civilian and military communications services- Cell phones and SatCom have joined the military
Military Satellite
Commercial Satellite
Global Hawk example
9-16
Design of UAV Systems
Communicationsc 2003 LM Corporation
Military communications
Military communications systems generally fall into one of two categories• Integrated - multiple users, part of the communications infrastructure• Dedicated - unique to a system
http://www.fas.org/man/dod-101/sys/ac/equip/tbmcs.htm
Integratedhttp://www.fas.org/man/dod-101/sys/smart/bgm-109.htm
Requires no other systems to operate anywhere in the world
Dedicated
9-17
Design of UAV Systems
Communicationsc 2003 LM Corporation
UAV architectures
UAV communication systems are generally dedicated
• The systems may have other applications (e.g. used by manned and unmanned reconnaissance) but each UAV generally has its own communications system
• US military UAVs have an objective of common data link systems across all military UAVs (e.g.TCDL)
• Multiple UAV types could be controlled
• Frequencies or geographic areas are allocated to specific UAVs to prevent interference or “fratricide”
UAV communications equipment is generally integrated with the control station
• This is particularly true for small UAVs and control stations
• Larger UAVs can have separate communications pallets
9-18
Design of UAV Systems
Communicationsc 2003 LM Corporation
US common data links
• Excerpts from - Survey of Current Air Force Tactical Data Links and Policy, Mark Minges, Information Directorate, ARFL. 13 June 2001
• A program which defines a set of common and interoperable waveform characteristics
• A full duplex, jam resistant, point-to-point digital, wireless RF communication architecture
• Used with intelligence, surveillance and reconnaissance (ISR) collection systems
• Classes & tech base examples
• Class IV (SatCom) - DCGS (Distributed Common Ground System)
• Class III (Multiple Access) - RIDEX (AFRL proposed)• Class II (Protected) - ABIT (Airborne Information transfer)
• Class I (High Rate) - MIST (Meteorological info. std. terminal)• Class I (Low Rate) - TCDL (Tactical CDL)
9-19
Design of UAV Systems
Communicationsc 2003 LM Corporation
Global Hawk GDT
Ku band SatCom terminal(D = 6.25m, W = 13950 lb)
“MIST”
UHF LOS antenna
UHF SatCom terminal(D = 2m, W =6500 Lb)
GDT = Ground “data terminal”
9-20
Design of UAV Systems
Communicationsc 2003 LM Corporation
Global Hawk ADT
ADT = Air “data terminal”
9-21
Design of UAV Systems
Communicationsc 2003 LM Corporation
TCDL ADT & GDT
Range goal - 200 Km at 15Kft
9-22
Design of UAV Systems
Communicationsc 2003 LM Corporation
Architecture
• Military• Commercial• “Common”
Function
• Up link (control)
• Launch and recovery• Enroute• On station• Payload control
• Down link (data)
• Sensor• System status
Next subject
Coverage
• Local area• Line of sight• Over the horizon
Other issues• Time delay
• Survivability
• Reliability• Redundancy• Probability of
intercept• Logistics
9-23
Design of UAV Systems
Communicationsc 2003 LM Corporation
Control functions
EnrouteLaunch and Recovery
http://www.fas.org/irp/program/collect/pioneer.htm
http://www.fas.org/irp/program/disseminate/uav_tcs.htm
http://www.fas.org/irp/program/collect/pioneer.htm
PayloadOn station
9-24
Design of UAV Systems
Communicationsc 2003 LM Corporation
Launch and recovery
Located at the operating base
• Control the UAV from engine start through initial climb and departure….and approach through engine shut down
• Communications must be tied in with other base operations- Usually 2-way UHF/VHF (voice) and land line
• Also linked to Mission Control (may be 100s of miles away)
Global Hawk Launch Recovery Element
2/28/2001
9-25
Design of UAV Systems
Communicationsc 2003 LM Corporation
Enroute
Launch and recovery or mission control responsibility
• Control the UAV through air traffic control (ATC) airspace- Usually 2-way UHF/VHF (voice)
• Primary responsibility is separation from other traffic - particularly manned aircraft (military and civil)- UAV control by line of sight, relay and/or SatCom data link
Global Hawk Mission Control Element
2/28/2001
9-26
Design of UAV Systems
Communicationsc 2003 LM Corporation
On station
Primary mission control responsibility • Control the UAV air vehicle in the target area using line
of sight, relay and/or SatCom data link- Bandwidth requirements typically 10s-100s Kpbs
• Control sometimes handed off to other users- Mission control monitors the operation
http://www.fas.org/irp/program/collect/predator.htmhttp://www.fas.org/irp/program/collect/predator.htm
9-27
Design of UAV Systems
Communicationsc 2003 LM Corporation
Payload
Primary mission control responsibility
• Control the sensors in the target area using line of sight, relay and/or SatCom data links- Sensor control modes include search and spot- High bandwidth required (sensor control feedback)
• Sensor control sometimes handed off to other users
EO/IR sensor control SAR radar control
9-28
Design of UAV Systems
Communicationsc 2003 LM Corporation
Down links
Down links carry the most valuable product of a UAV mission
• UAV sensor and position information that is transmitted back for analysis and dissemination - Exception, autonomous UAV with on board storage
• Or UCAV targeting information that is transmitted back for operator confirmation
Real time search mode requirements typically define down link performance required
• Non-real time “Images” can be sent back over time and reduce bandwidth requirements
Line of sight down link requirements cover a range from a few Kbps to 100s of Mbps, SatCom down link requirements are substantially lower
9-29
Design of UAV Systems
Communicationsc 2003 LM Corporation
Radar “imagery”
High resolution “imagery” (whether real or synthetic) establishes the down link bandwidth requirement
• Example - Global Hawk has 138,000 sqkm/day area search area at 1m resolution. Assuming 8 bits per pixel and 4:1 compression, the required data rate would be 3.2 Mbps to meet the SAR search requirements alone*
- In addition to this, the data link has to support 1900, 0.3 m resolution 2 Km x 2 Km SAP spot images per day, an equivalent data rate of 2.0 Mbps
- Finally there is a ground moving target indicator (GMTI) search rate of 15,000 sq. Km/min at 10 m resolution, an implied data rate of about 5Mbps
• Total SAR data rate requirement is about 10 Mbps
*See the payload lesson for how these requirements are calculated
Design of UAV Systems
Communicationsc 2003 LM Corporation
EO/IR data
EO/IR requirements are for comparable areas and resolution. After compression, Global Hawk EO/IR bandwidth requirements estimated at 42 Mbps*
This is why Global Hawk has a high bandwidth data link
2/28/2002
EO spot image IR spot image
* Flight International, 30 January 2002
9-30
9-31
Design of UAV Systems
Communicationsc 2003 LM Corporation
System status data
Air vehicle system status requirements are small in comparison to sensors
- Fuel and electrical data can be reported with a few bits of data at relatively low rates (as long as nothing goes wrong - then higher rates required)
- Position, speed and attitude data files are also small, albeit higher rate
- Subsystem (propulsion, electrical, flight control, etc) and and avionics status reporting is probably the stressing requirement, particularly in emergencies
Although important, system status bandwidth requirements will not be design drivers
- A few Kbps should suffice
Once again, the sensors, not system status, will drive the overall data link requirement
Coverage
• Local area• Line of sight• Over the horizon
Other issues• Time delay
• Survivability
• Reliability• Redundancy• Probability of
intercept• Logistics
9-32
Design of UAV Systems
Communicationsc 2003 LM Corporation
Next subject
Architecture
• Military• Commercial• “Common”
Function
• Up link (control)
• Launch and recovery• Enroute• On station• Payload control
• Down link (data)
• Sensor• System status
9-33
Design of UAV Systems
Communicationsc 2003 LM Corporation
Local area communications
• Close range operations (e.g., launch and recovery) typically use omni-directional data links
- All azimuth, line of sight- Air vehicle and ground station impact minimal
• Communications must be tied in with other base operations
- Usually 2-way UHF/VHF (voice) and land line
Omni-directional antennae
http://www.fas.org/irp/program/collect/pioneer.htm
PioneerDipole
Dish
• Typically require directional data links - RF focused on control station and/or air vehicle
- Impact on small air vehicles significant- Impact on larger air vehicles less significant- Significant control station impact
• Communications requirements include air traffic control- Usually 2-way UHF/VHF (voice)
9-34
Design of UAV Systems
Communicationsc 2003 LM Corporation
Long range comms (LOS)
Hunter
http://www.fas.org/irp/program/collect/pioneer.htm
Global Hawk Steerable
Relay aircraft - existing line of sight equipment• Minimal air vehicle design impact• Major operational impact
9-35
Design of UAV Systems
Communicationsc 2003 LM Corporation
Over the horizon options
TUAV
http://www.fas.org/irp/program/collect/pioneer.htm
• Low bandwidth - minimal design impact, major operational• High bandwidth - major impact (design and operational)
SatCom
9-36
Design of UAV Systems
Communicationsc 2003 LM Corporation
Global Hawk SatCom
Ku-band antenna Diameter = 1.22 m
D = 6.25m, W = 13950 lb
• Transmitter, receiver- Size- Weight- Location
• Antennae- Ditto
• Power and cooling• Cost and complexity
Design issues
• Link availability• Bandwidth availability• Logistics
- Transportability• Operations and support cost
Operational issues
Coverage
• Local area• Line of sight• Over the horizon
Other issues• Time delay
• Survivability
• Reliability• Redundancy• Probability of
intercept• Logistics
9-37
Design of UAV Systems
Communicationsc 2003 LM Corporation
Architecture
• Military• Commercial• UAV
Function
• Up link (control)
• Launch and recovery• Enroute• On station• Payload control
• Down link (data)
• Sensor• System status
9-38
Design of UAV Systems
Communicationsc 2003 LM Corporation
• The time required to transmit, execute and feed back a command (at the speed of light)
- A SatCom problem
• Example:
- 200 Km LOS @ c = 3x10^5 Km/sec- Two way transmission
time = 1.33 msec
- Geo stationary Satcom at 35,900 Km - Two way transmission
time = 240 msec
Other issues - time delay
Two-way transmission time
1
10
100
1000
100 1000 10000 100000
One way distance (Km)
LOSLEOMEOGEOAllPower (All)
Raw data from, Automated Information Systems Design Guidance - Commercial Satellite Transmission, U.S. Army Information Systems Engineering Command
(http://www.fas.org/spp/military/docops/army/index.html)
Inmarsat M(500 msec?)
9-39
Design of UAV Systems
Communicationsc 2003 LM Corporation
• Also known as data “latency” or “lag”- Limited by speed of light and “clock speed”
• All systems have latency- Human eye flicker detection - 30 Hz (33 msec delay)- Computer screen refresh rate - 75 Hz (13 msec)- Computer keyboard buffer latency - 10 to 20 msec- LOS communications - 2 msec- LEO SatCom - 10 msec- MEO Satcom - 100 msec- GEO Satcom - 200 to 300 msec- Typical human reaction - 150-250 msec
• Acceptable overall system lag varies by task< 40 msec for PIO susceptible flight tasks (low L/D)< 100 msec for “up and away” flight tasks (high L/D)
• When OTH control latency > 40 msec, direct control of a UAV is high risk (except through an autopilot)
Time delays and UAVs
9-40
Design of UAV Systems
Communicationsc 2003 LM Corporation
• The preferred reliability solution• Separate back up data link(s)
• Most modern UAVs have redundant data links• Global Hawk has 4 (two per function)
- UHF (LOS command and control)- UHF (SatCom command and control)- CDL (J-band LOS down link)- SHF (SatCom Ku band down link)
• Dark Star also had four (4)• Predator, Shadow 200 have two (2)
• Most UAVs also have pre-programmed lost link procedures
- If contact lost for TBD time period (or other criteria) return to pre-determined point (near recovery base)- Loiter until contact re-established (or fuel reaches
minimum levels then initiate self destruct)
Other issues - redundancy
9-41
Design of UAV Systems
Communicationsc 2003 LM Corporation
Probability of intercept
• Probability that an adversary will be able to detect and intercept a data link and be able to 1. Establish track on the UAV position2. Interfere with (or spoof) commands
• Purely a military UAV issue• No known civil equivalent
• Some well known techniques- Spread spectrum
- Random frequency hopping- Burst transmissions
- Difficult to detect and track - Power management
- No more power than required to receive- Narrow beam widths
- Difficult intercept geometry
Wide beamMax. power
Narrow beamMin. power
Adversary
9-42
Design of UAV Systems
Communicationsc 2003 LM Corporation
More issues
• Power and cooling
• Communications equipment (especially transmitters) require significant power and cooling to meet steady state and peak requirements - At low altitudes, meeting these power and cooling
requirements typically is not an issue- At high altitude, both are a problem since power
and cooling required ≈ constant and ….- Power available approximately proportional - Cooling air required(cfm) approximately
proportional 1/; one reason why high-altitude aircraft use fuel for cooling (also keeps the fuel from freezing!)
9-43
Design of UAV Systems
Communicationsc 2003 LM Corporation
A significant part of transport requirements are associated with communications equipment
C-141B transport configuration
Other issues - logistics
9-44
Design of UAV Systems
Communicationsc 2003 LM Corporation
Next subject
• RF basics• Data link types• Frequency bands• Antennae• Equations
• Communications issues• Architecture• Function• Coverage• Etc.
• Sizing (air and ground)• Range • Weight• Volume• Power
• Example problem
- Given 2 platforms at distance (D1+D2) apart at altitudes h1 and h2 above the surface of the earth:
Re
D1 D2 h2
hmin
h1
D1+D2 Re*{ArcCos[(Re+hmin)/(Re+h2)]+ ArcCos[(Re+hmin)/(Re+h1)]} (9.1)
Re ≈ 6378 km (3444 nm)hmin = intermediate terrain or weather avoidance altitude (≈ 20kft)*
ArcCos[ ] is measured in radians*not applicable if h1 and/or h2 lower than hmin
- From geometry
where
and
9-45
Design of UAV Systems
Communicationsc 2003 LM Corporation
Line of sight (LOS) calculations
9-46
Design of UAV Systems
Communicationsc 2003 LM Corporation
RF line of sight
• Due to earth curvature and atmospheric index of refraction, RF transmissions bend slightly and the RF line of sight (LOS) is > the geometric LOS by a factor ≈ √4/3 (Skolnik, Radar Handbook, page 24-6)
• Another equation for communication LOS can be found using a simple radar horizon equation from Skolnik (page 24-8) where:
- LOS(statute miles) ≈ √2*h(ft) (9.2)or
- LOS(nm) ≈ 0.869√2*h(ft) (9.3)• Note that the ratio of Eqs 9.1 and 9.3 for h1 = hmin =
0 and h2 = h is √4/3 ; e.g. LOS (Eq 9.1) = 184 nm @ h2 = 30Kft while LOS (Eq 9.3) = 213 nm
•
- We will assume that the √4/3 factor will correct any geometric LOS calculation including 9.4 when h1 and h2min ≠ 0
9-47
Design of UAV Systems
Communicationsc 2003 LM Corporation
Grazing angle effects
• Ignore the small differences between LOS and LOS’• The equation predicts published Global Hawk comm ranges at 0.75
• Given a platform at altitude h at grazing angle above the horizon:
Reh
Local horizon
LOS’
• From geometry, the slant range (LOS’) will be given by:(Re+h)^2 = LOS’^2 + Re^2 -2*LOS’*Re*Cos (/2+)
orLOS’^2 - [2*Re*Cos (/2+)]*LOS’ + [Re^2 - (Re+h)^2] = 0
where LOS is the root of a quadratic equation of the form a*x^2+bx+c = 0 or x = [-b±sqrt(b^2-4*a*c)]/2*a
which we then multiply by √4/3 to adjust for atmospheric effects
(9.4)
LOS
9-48
Design of UAV Systems
Communicationsc 2003 LM Corporation
Airborne relay
A system level solution for an organic over the horizon (OTH) UAV communications capability• Requires that relay UAV(s) stay airborne at all times
- For extended range and/or redundancy• Also requires separate communication relay payload
- In addition to basic UAV communication payloadBut relay platform location is critical. Example:- Four (4) WAS UAVs loiter at 27 Kft and one (1) ID
UAV loiter at 10 Kft over a 200 nm x 200 nm combat area located 100 nm from base
- Two (2) WAS UAVs closest to base function as communications relays for the three other UAVs
- Typical terrain altitude over the area is 5 Kft- How would a WAS relay have to operate to provide
LOS communications to the ID UAV at max range?
9-49
Design of UAV Systems
Communicationsc 2003 LM Corporation
• LOS defines max communication distance for relay - At =0.75, LOS from base = 156.7 nm vs. 158 nm req’d - At hmin = 5 kft, LOS from ID UAV at 10 Kft to WAS relay at 27 Kft = 269.2 nm vs. 212 nm req’d
• WAS altitude inadequate to meet base relay requirement
Relay example
100 nm
200 nm x 200 nm
158 nm 10 Kft27 Kft
156.7 nm
269.2 nm
212 nm
- Altitude increase to 27.4 Kft required
9-50
Design of UAV Systems
Communicationsc 2003 LM Corporation
• There is little public information available on UAV data links to use for initial sizing- Including both air and ground data “terminals”
Short hand notation - ADT and GDT• Three sources
1. Janes UAVs and Targets, Issue 14, June 2000- Mostly military UAV data links
2. Unpublished notebook data on aircraft communications equipment - Both military and civil, not UAV unique
3. Wireless LAN data - Collected from the internet, not aircraft qualified - Indicative of what could be done with advanced
COTS technology• For actual projects, use manufacturer supplied data
Next - sizing data
9-51
Design of UAV Systems
Communicationsc 2003 LM Corporation
ADT range and power
LOS data links
0
40
80
120
160
200
0 100 200 300
Line of sight range (nm)
Calculate LOS range
Equations 9.1-9.4
Estimate RF output power required
9-52
Design of UAV Systems
Communicationsc 2003 LM Corporation
Initial sizing - ADT Satcom
Parametric correlation basis
Known correlation between band width or data rate and frequency
- Bandwidth availability increases with frequency
Parametric data source
All Satcom data links Frequency range 0.24 - 15 GHzBandwidth range 0.6 Kbps - 5.0 Mbs
Select Bandwidth
Select frequency
Bandwidth correlation
1
10
100
1000
10000
100000
0 3 6 9 12 15
Frequency (GHz)
Global HawkPredatorInmarsatUHFallExpon. (all)
9-53
Design of UAV Systems
Communicationsc 2003 LM Corporation
ADT power required
Parametric data source
Military line of sight data linksFrequency range 30 MHz - 15 GHzBandwidth range 0.01-5.0 Mbs
Estimate input power requirements
- LOS- SatCom (GEO)
Power conversion
0
50
100
150
200
250
0 200 400 600 800 1000
Power consumption (W)
Line of sightSatCom
9-54
Design of UAV Systems
Communicationsc 2003 LM Corporation
ADT weight
Parametric data source
Janes and unpublished dataFrequency range 30 MHz - 15 GHzBandwidth range 0.01-5.0 Mbs
Estimate weight
- LOS- SatCom (GEO)
Note - excludes antennae
Weight-power
0
10
20
30
40
50
60
70
80
90
0 200 400 600 800 1000
Power consumption (W)
Line of sightSatCom
9-55
Design of UAV Systems
Communicationsc 2003 LM Corporation
ADT volume
Parametric data source
All LOS data links & modemsFrequency range 30 MHz - 15 GHzBandwidth range 0.01-5.0 Mbs
Estimate volume
- LOS- SatCom (GEO)
Density
0
20
40
60
80
0 1000 2000 3000 4000 5000 6000
Volume (in^3)
LOS Datalinks
SatCom data links
Wireless LAN
Linear (SatComdata links)Linear (LOSDatalinks)
Parametric correlation basis
Known correlation between bandwidth required and size
Antenna characteristic “size” defined as following:
- For EHF : square root of antenna area (when known) or cube root of installed volume
- For UHF : antenna length (blade) or diameter (patch)
9-56
Design of UAV Systems
Communicationsc 2003 LM Corporation
ADT Satcom antenna
Parametric data source
All Satcom data link antennaFrequency range 0.24 - 15 GHzBandwidth range 0.6 Kbps - 5.0 Mbs
Estimate antenna “size”
Calculate area, volume or length as appropriate
Satcom antenna size parametric
0
10
20
30
40
50
1 100 10000 1000000
Data rate (Kbps)
UHFL bandKu bandallLog. (all)
9-57
Design of UAV Systems
Communicationsc 2003 LM Corporation
ADT satcom antenna
Parametric data source
All Satcom data link antennaFrequency range 0.24 - 15 GHzBandwidth range 0.6 Kbps - 5.0 Mbs
Estimate antenna weight
Satcom antenna weight parametric
0
20
40
60
80
100
5 10 15 20 25 30
Characteristic size (in)
UHFL bandKu bandall
9-58
Design of UAV Systems
Communicationsc 2003 LM Corporation
More ADT LOS data
Janes UAV data links
0.010
0.015
0.020
0.025
0.030
0.035Median = .025
Other military data links
0.010
0.030
0.050
0.070
0.090
Median = .045
Wireless LAN
0.010
0.015
0.020
0.025
0.030
0.035
0.040
0.045Median = .023
Airborne weight & volume
0
10
20
30
40
50
60
0 200 400 600 800
Volume (cuin)
Janes UAV data links
Other military data links
COTS wireless LAN
Parametric data source All LOS data links & modemsFrequency range 30 MHz - 15 GHzBandwidth range 0.01-5.0 Mbs
9-59
Design of UAV Systems
Communicationsc 2003 LM Corporation
• All systems on an air vehicle have an installation weight and volume penalty (more in Lesson 19)• We will assume a typical installation at 130% of dry
uninstalled weight• We will make this assumption for all installed items
(mechanical systems, avionics, engines, etc.)• Installed volume is estimated by allowing space
around periphery, assume 10% on each dimension • Installed volume = 1.33 uninstalled volume
• For frequently removed items or those requiring air cooling, we will add 25% to each dimension• Installed volume = 1.95 uninstalled volume• Payloads and data links should be installed this way
Installation considerations
9-60
Design of UAV Systems
Communicationsc 2003 LM Corporation
GDT options
There are a few GDT system descriptions in Janes and on the internet for UAV applications.- Little technical data is provided but in general they are
large- The CL-289 GDT is integrated into a truck mounted
ground control station and includes a 12 meter hydraulic antenna mast
- The Elta EL/K-1861 has G and I-band dish antennae (6 ft and 7ft diameter, respectively)
- The AAI GDT appears to be about a 2 meter cube excluding the 1.83 m C-band antenna
- Smaller man portable systems are also described but little technical performance data is included
The following parametrics are very approximate and should be used only until you get better information from manufacturers
9-61
Design of UAV Systems
Communicationsc 2003 LM Corporation
GDT parametrics
GDT weight vs. volume
0
3000
6000
9000
12000
15000
18000
0 50 100 150 200 250 300
Weight (lbs)
GDT weight vs. power
0
200
400
600
800
1000
1200
0 100 200 300
Weight (lb)
GDT Antenna Size
0
2
4
6
0 5 10 15 20
Frequency (GHz)
9-62
Design of UAV Systems
Communicationsc 2003 LM Corporation
Expectations
You should understand
• Communications fundamentals• UAV unique communications issues • How to calculate communication line of sight • How to define (size) a system to meet overall
communication requirements
9-63
Design of UAV Systems
Communicationsc 2003 LM Corporation
Final subject
• RF basics• Data link types• Frequency bands• Antennae• Equations
• Communications issues• Architecture• Function• Coverage• Etc.
• Sizing (air and ground)• Range • Weight• Volume• Power
• Example problem
9-64
Design of UAV Systems
Communicationsc 2003 LM Corporation
Example problem
• Five medium UAVs, four provide wide area search, a fifth provides positive target identification- WAS range required (95km) not a challenge
• Only one UAV responds to target ID requests• No need to switch roles, simplifies ConOps• No need for frequent climbs and descents
• Communications distances reasonable (158nm & 212 nm)
• Speed requirement = 280 kts • Air vehicle operating altitude differences reasonable• We will study other
options as trades• What is a reasonable
communications architecture?
• How big are the parts?
100 nm
200 nm x 200 nm
158 nm
27.4 Kft
10 Kft27.4 Kft 27.4 Kft
212 nm
Altitude increase required to meet LOS relay requirement
9-65
Design of UAV Systems
Communicationsc 2003 LM Corporation
• Parametric data is used to size (1) a basic UAV data link and (2) a communications relay payload• We assume both are identical and that all UAVs carry
both, allowing any UAV to function as a relay• Provides communication system redundancy
• Parametric sizing as follows (for each system)• Max range = 212 nm RF power = 110 W (Chart 51)• Power consumption = 500 W (Chart 53)• Weight = 27 lbm (Chart 54)• Volume = 500 cuin (Chart 55)
• We have no non-Satcom antenna parametric data and simply assume a 12 inch diameter dish, weighing 25 lbm with volume required = 2 cuft• If you have no data, make an educated guess,
document it and move on• We will always check the effect later
• We include communications in our payload definition
ADT sizing
9-66
Design of UAV Systems
Communicationsc 2003 LM Corporation
• We have little GDT parametric sizing date and simply assume an ADT consistent input power requirement (500W) and use the chart 60 parametrics to estimate weight and volume• 250 lbm and 9.5 cuft
• Antenna size will be a function of frequency and bandwidth which we will select after assessing our payload down link requirements
GDT sizing
9-67
Design of UAV Systems
Communicationsc 2003 LM Corporation
Requirements update
• System element• GDT weight/volume/power excluding antenna (each)
= 205 lbm/9.5 cuft/500 W• GDT installations required = 2
• Payload element• Installed weight/volume/power = TBD• WAS
• Range/FOR /resolution/speed = 95 km/45/10m/2mps• Uninstalled weight/volume/power = TBD
• ID • Type/range/resolution = TBD/TBD/0.5m• Uninstalled weight/volume/power = TBD
• Communications • Range/type = 212nm/air vehicle and payload C2I
• Uninstalled weight/volume/power 52 lbm/2.3 cuft/500 W• Range/type = 158nm/communication relay
• Uninstalled weight/volume/power 52 lbm/2.3 cuft/500 W
•Air vehicle element•Cruise/loiter altitudes = 10 – 27.4Kft
9-68
Design of UAV Systems
Communicationsc 2003 LM Corporation
Homework
Assess communication requirements for your project and develop an architecture that you think will work(1) Define a communications architecture that includes
redundancy considerations(2) Calculate LOS distances from base to vehicle(s) at
the required operating altitudes.- Assume minimum grazing angle () = 0.75
(3) If your architecture includes airborne relay, calculate the relay distances at your operating altitudes- Use the example problem as a guide
(4) Determine the ADT weight, volume and power req’d(5) Document your derived requirements
Submit your homework via Email to Egbert by COB next Thursday. Document all calculations
9-69
Design of UAV Systems
Communicationsc 2002 LM Corporation
Intermission