Post on 23-Feb-2018
7/24/2019 11. Valves and Piping
1/118
1
Module 11
PIPINGS and VALVES
7/24/2019 11. Valves and Piping
2/118
2
Course Contents
1. Pipe
2. Piping standard
- Nominal pipe diameter - Scedule num!er
- Piping standards code
- "u!es
- #ittings and oter piping au$iliaries
%. Metod o& 'oining sections - "readed
- (ell and spigot
- #langed
- )elded connection
- #itting*. "+pes o& &langed 'oints
,. E$pansion 'oints
. (linds
. Spaces
7/24/2019 11. Valves and Piping
3/118
%
Course Contents
/. Val0es
- "+pes o& 0al0es
. Val0es
- Gate 0al0e
- Glo!e 0al0e
- iapragm 0al0e
- Plug 0al0e
- (all 0al0e
- (utter&l+ 0al0e
- Needle 0al0e
- Cec3 0al0e - Sa&et+ 0al0e
14. #unction o& 0al0e
11. (asic control &unction o& 0al0es
7/24/2019 11. Valves and Piping
4/118
*
Course Contents
14. Application o& Val0e t+pes
11. Val0e ratings
12. Val0e operation and maintenance
1%. o5s and don5t &or !etter 0al0e ser0ice
1*. Pressure relie0ing de0ices
- 6o7 ig pressure de0elops
- "+pes o& pressure relie0ing de0ices
1,. e&inition o& pressure relie& terms
7/24/2019 11. Valves and Piping
5/118
,
Pipes
8 Piping s+stems are te arteries and 0eins o& a petrocemical plant'ust as te+ are in te uman !od+. In a petrocemical9 piping
s+stems andle all li:uids9 solids9 gas or 0apor.8 Material is &re:uentl+ stored and andled in te &luid state. Most &luid
cannot !e andled in open cannels !ut re:uired closed ducts.
8 In ancient tese ducts 7ere ollo7ed logs and later te+ 7ere madeo& section o& 7ood or o& potter+.
8 e0elopment o& iron !rougt a!out te manu&acture o& cast iron and7rougt iron pipes.
8 An+ structural material no7 a0aila!le is used &or pipe in application7ere its peculiar ad0antages are most 0alua!le.
7/24/2019 11. Valves and Piping
6/118
Piping Standards
Nominal pipe diameter
Pipe si;es are !ased on te appro$imate diameter and are reported as
nominal pipe si;es. Altoug te 7all tic3ness 0aries depending on
te scedule num!er9 te outside diameter o& an+ pipe a0ing a gi0en
nominal si;e is constant and independent o& te scedule num!er. "is
permits te use o& standard &ittings and treading tools on pipes o&
di&&erent scedule num!ers
7/24/2019 11. Valves and Piping
7/118
Piping Standards
Scedule num!er
8 Pipes 7ere originall+ classi&ied on te !asis o& 7all tic3ness
as standard ? 1444 Ps@Ss
7ere Ps ? sa&e 7or3ing pressure
Ss ? sa&e 7or3ing &i!er stress
7/24/2019 11. Valves and Piping
8/118
/
Piping Standards
Scedule num!er
8 "en scedule num!ers are in use at present.
8 "ese are 149 249 *49 49 /49 1449 1249 1*49 14
8 #or pipe diameters up to 14 in9 scedule *4 corresponds to te
&ormer standardB pipe and scedule /4 corresponds to te
&ormer e$tra strongB pipe.
7/24/2019 11. Valves and Piping
9/118
Piping Standards
Scedule num!er
6o7 te+ came up 7it te &ormula(ursting pressure o& a tin 7alled c+linder ma+ !e estimated &rom
te &ollo7ing e:uation>
P!? 2S"tm@m 7ere> P!? !ursting pressure S"? tensile strengt
tm? minimum 7all tic3eness
m? mean diameter
7/24/2019 11. Valves and Piping
10/118
14
Piping Standards
Scedule num!er
A sa&e 7or3ing pressure Ps can !e e0aluated &rom e:uation i& te
tensile strengt is replaced !+ a sa&e 7or3ing &i!er stress Ss
Ps? 2Sstm@m
7/24/2019 11. Valves and Piping
11/118
11
Piping Standards
Piping standard codes
8 "e American National Standards Institute
7/24/2019 11. Valves and Piping
12/118
12
Piping Standards
Piping standard code
7/24/2019 11. Valves and Piping
13/118
1%
Piping Standard
"u!ing
Copper tu!ing9 !rass tu!ing are used e$tensi0el+ in industrial
operations. Fter metals9 suc as nic3lel and stainless steel9 are also
a0aila!le in te &orm o& tu!ing.
Altoug pipe speci&ications are !ased on standard nominal si;es9
tu!ing specs are !ased on te actual outside diameter 7it a
designated 7all tic3ness.
Con0entional s+stem9 suc as te (irmingam 7ire gauge
7/24/2019 11. Valves and Piping
14/118
1*
Piping Standard
#ittings and oter piping au$iliaries
8 #ittings9 &langes9 0al0es9 &lo7 meters9 steam traps and man+ oter
au$iliaries are o&ten rated on te !asis o& te sa&e operating
pressure as
2, psi lo7 pressure 12, psi - standard
2,4 psi e$tra ea0+
%44 to 149444 - +draulic
7/24/2019 11. Valves and Piping
15/118
1,
Metod o& Hoining Sections
Metod o& 'oining sections
"e metods o& 'oining sections are generall+ similar &or all
materials. "e principal metods in0ol0e are
1. "readed
2. (ell and spigot
%. #langed
*. )elded connections
,. #itting
7/24/2019 11. Valves and Piping
16/118
1
"readed Hoints
8 "readed pipe is most commonl+ encountered iin industr+ !ecause
practicall+ all small si;es o& pipe are 'oined !+ tismetod9 7eterall small si;es o& pipe are 'oined !+ tismetod9 7eter
&a!ricated o& steel9 7rougt iron9 cast iron9 !rass9 or plastic.&a!ricated o& steel9 7rougt iron9 cast iron9 !rass9 or plastic.
8 "is s+stem is simple !ecause te outside diameters o& te pipe are"is s+stem is simple !ecause te outside diameters o& te pipe are
3ept constant 7it a tolerance o& 1@* in. o0ersi;e and 1@%2 in.3ept constant 7it a tolerance o& 1@* in. o0ersi;e and 1@%2 in.undersi;e9 and te inside diameters o& &ittings are 3ept 7itin teundersi;e9 and te inside diameters o& &ittings are 3ept 7itin te
same limits9 regardless o& materials.same limits9 regardless o& materials.
8 "e tolerance &or te 7all tic3ness o& te di&&erent materials 0aries"e tolerance &or te 7all tic3ness o& te di&&erent materials 0aries
!ut is usuall+ 12., per cent.!ut is usuall+ 12., per cent.
8 Pipe larger tan 12in. Is rarel+ treaded9 and te outside diameterPipe larger tan 12in. Is rarel+ treaded9 and te outside diametercorresponds to te nominal pipe si;e.corresponds to te nominal pipe si;e.
8 Standard lengts o& pipe are &rom 1 to 22 &eet.Standard lengts o& pipe are &rom 1 to 22 &eet.
7/24/2019 11. Valves and Piping
17/118
1
(ell and Spigot Hoints
(ell and spigot connected pipe andle more &luid tan an+ oter
connection since it is te most practical t+pe o& 'oint in large pipe
si;es 7en pipes are made o& materials oter tan steel. "ese
'oints are usuall+ cal3ed 7it oa3um and lead !ut te mecanical
'oint is !ecoming more popular !ecause o& te tigter 'oint9 simplicit+
o& installation9 greater latitude o& angular displacement and
e$pansion. "ese 'oints ma+ !e loc3edB 7it a groo0e in te spigot
7ic pre0ents pulling apart te 'oint9 roll onB 7it a ru!!er gas3et
tigtened 7it a !olted ring or scre7ed glandB9 7it a ring gland
dra7n up against te gas3et 7en scre7ed into treads in te !ell.
Materials &or pipe 'oined in tis manner are usuall+ cast iron9 cla+9
or concrete9 altoug glass9 plastic and cement as!estos are
sometimes emplo+ed.
7/24/2019 11. Valves and Piping
18/118
1/
)elded Connections
8 "e modern trend &or pipe in si;es a!o0e 2 in. is to7ard more
7elded connections. No treading9 cal3ing9 or !olts is needed9 and
no gas3ets are re:uired 7en te s+stem is &used into an un3no7n
line o& material.
8Pipe ends needs no treatment oter tan scar&ing
pieces &rom pipe sections.
8 #ittings and 0al0es are o& steel and are o& t7o t+pes9 !utt 7eld and
soc3et 7eld. "e !utt 7eld &ittings are o& te same dimension as te
pipe9 and te soc3et 7eld &ittings a0e enlarged ends similar to
treaded &ittings9 !ut te pipe slips into place and is &illet 7elded.
7/24/2019 11. Valves and Piping
19/118
1
#ittings
"readed 'oint &ittings
8 Couplings 'oin successi0e straigt lengt o& pipes 7it no cange
in direction or si;e.
8 Deducing couplings used 7en si;e is to !e reduced or enlarged.
8 El!o7s used 7en direction is to canged
7/24/2019 11. Valves and Piping
20/118
24
#ittings
"readed 'oint &ittings
7/24/2019 11. Valves and Piping
21/118
21
#ittings
"readed 'oint &ittings
7/24/2019 11. Valves and Piping
22/118
22
#ittings
)elded connections
#ittings are o& steel and are o& 2 t+pes9 !utt 7eld and soc3et 7eld.
"e !utt 7eld &ittings are o& te same dimension as te pipe9 and te
soc3et 7eld &ittings a0e enlarged ends similar to treaded to
treaded &ittings9 !ut te pipe slips into place and is &illet7elded.7elded.
#ittings are similar to e:ui0alent treaded t+pe.#ittings are similar to e:ui0alent treaded t+pe.
7/24/2019 11. Valves and Piping
23/118
2%
#ittings
(ell and spigot connections
#ittings#ittings Jo& te same materials as te pipeK are similar in t+pe and
&unction to tose &or treaded pipe.
7/24/2019 11. Valves and Piping
24/118
2*
#ittings
Compression &ittings
8 Compression &ittings are 7idel+ used &or small si;ed tu!ing at !ot
lo7 and ig pressure. "ese are con0enient and e&&icient9
particularl+ i& te connection is to !e !ro3en.
7/24/2019 11. Valves and Piping
25/118
2,
#langed Hoints
#langed 'oints are te most common metod &or 'oining pipe in si;es
2 inces and a!o0e. "e use o& &langes allo7s &or ma3ing te piping
up in sections tat are eas+ to andle and also allo7s access &or
cleaning9 draining9 etc.
1. Soc3et 7elding &langes
2. Slip on 7elding &langes
%. "readed &langes
*. )elding nec3 &langes
,. Lap 'oint &langes
7/24/2019 11. Valves and Piping
26/118
2
#langed Hoints
Soc3et 7elding &langes
8 Soc3et 7elding &langes are 7idel+ used &or moderate ser0ice9
particularl+ in te smaller si;es9 !ecause o& te ease o& &it p and
alignment. Altoug usuall+ 7elded at te &lange u! onl+9 te pipe
end ma+ also !e 7elded 7itout a0ing to re&ace te &lange. "e
pipe end 7eld can !e ground to pro0ide a smoot !ore.
7/24/2019 11. Valves and Piping
27/118
2
#langed Hoints
Slip-on )elding #langes
8 Slip-on &langes are popular &or normal ser0ice conditions !ecause o&
te ease o& &it up and alignment and te greater tolerance
permissi!le in cutting te pipe to lengt. Decommended &a!ricationpractice is to 7ed at !ot te &lange u! and te pipe end.
7/24/2019 11. Valves and Piping
28/118
2/
#langed Hoints
"readed #langes
8 "readed &langes are 7idel+ used !ecause no 7elding e:uipment is
re:uired &or assem!l+ and !ot te pipe and &lange can !e
completel+ sal0aged upon dismantling. Accuratel+ cut9 clean9
tapered pipe treads dimensioned to ANSI A2. 1 Pipe "reads9
assure strong9 tigt 'oints.
7/24/2019 11. Valves and Piping
29/118
2
#langed Hoints
)elding Nec3 #langes
8 )elding nec3 &langes are designed to !e !utt 7elded to te pipe.
"e long tampered u! rein&orces te &lange9 permits stress-
relie0ing9 magna&lu$ing or $-ra+ing te 7eld9 7en re:uired9 and
remo0es te &lange &ace &rom te eat a&&ected ;one. "ese
ad0antages ma3e 7elding nec3 &langes particularl+ suita!le &or
se0ere ser0ice in0ol0ing ig pressure9 e$treme temperatures9 or
a;ardous &luids.
7/24/2019 11. Valves and Piping
30/118
%4
#langed Hoints
Lap Hoint #langes
8 Lap 'oint &langes9 7ile re:uiring a separate end connector9 pro0ide
a 'oint in 7ic te product does not come in contact 7it te &lange.
In addition9 te a!ilit+ o& te &lange to rotate simpli&ies assem!le and
alignment o& !olting on s+stems re:uiring &re:uent dismantling.
8 Scre7ed &langes must !e seal 7elded a&ter te scre7ed 'oint is
made up tigt. "reading o& pipe a!o0e 2B is di&&icult and tis t+pe is
not used too o&ten.
8 Slip-on &langes are 7idel+ used !ecause o& teir lo7 cost9 ease o&
&it-up and alignment9 o7e0er9 te+ are not too good &or ser0ice7ere te temperature and pressure &luctuate. In some ser0ices
corrosion o& te internal 7eld ma+ !e a pro!lem.
7/24/2019 11. Valves and Piping
31/118
%1
#langed Hoints
Lap Hoint #langes
7/24/2019 11. Valves and Piping
32/118
%2
#langed Hoints
Lap Hoint #langes
7/24/2019 11. Valves and Piping
33/118
%%
E$pansion Hoints
E$pansion Hoints
8 All metals e$pand 7it increasing temperature. Steel pipe is no
e$ception to tis rule. E$pansion must !e considered to
accommodate te cange in lengt in te cange &rom atmosperic
temperature to operating temperature. E$pansion 'oints are used to
a!sor! te e&&ect o& te increased lengt 7it temperature. "ese
can !e !ends or corrugated e$pansion 'oints. "e attaced piping
must !e properl+ ancored and guided to direct te e$pansion to
utili;e te e$pansion to utili;e te e$pansion 'oint most e&&ecti0el+.
7/24/2019 11. Valves and Piping
34/118
%*
(linds
(linds are a piping item used e$tensi0el+ in te plant. A !lind is used
to pro0ide positi0e isolation in !et7een piping &langes and tus
insure tat an+ lea3age tat ta3es place 7ill !e to te atmospere
and not troug te pipe.
8 Normall+9 !linds are used to prepare 0essels or tan3s &or entr+
and to isolate e:uipment and piping in order to pro0ide
complete sa&et+ in 7elding.
8 (linds are also used &or +drostatic testing !ut in tis case te+
must !e o& special design in order to andle te test pressures
tat 7ill !e in0ol0ed.
7/24/2019 11. Valves and Piping
35/118
%,
Spacers
Spacers are re:uired 7en tere is a !lind o& apprecia!le tic3ness
to !e used. It is ordinaril+ impossi!le to spring te &langes &ar
enoug apart to install a !lind o& tic3ness !e+ond in.
8 nder te a!o0e conditions a spacer is re:uired to ta3e up te
space occupied !+ te !lind 7en te e:uipment is returned to
operating condition.
8 Sometimes te !lind and te spacer are attaced to eac oter
and in tis case it is 3no7n as &igure / or spectacle !lind.
7/24/2019 11. Valves and Piping
36/118
%
Val0es
8 Val0es are used &or te control o& 0olume and pressure o& &luids
mo0ing troug piping or in enclosed 0essels. "e+ ma+ !e
operated automaticall+ or !+ and. "+pe o& construction is as 0aried
as te operations 7itin te plant eac is designed &or te ser0ice
to !e per&ormed.
7/24/2019 11. Valves and Piping
37/118
%
Val0es
"+pes o& 0al0es
1. Gate 0al0es
2. Glo!e 0al0es
%. iapragm 0al0es
*. Plug 0al0es,. (all 0al0es
. (utter&l+ 0al0es
. Needle 0al0es
/. Cec3 0al0es. Sa&et+ 0al0es
7/24/2019 11. Valves and Piping
38/118
%/
Val0es
Gate 0al0es
8 "e gate 0al0e is pro!a!l+ te most 7idel+ used 0al0e in plantoperations9 particularl+ in te larger si;es o& piping installations andtose o& te most se0ere ser0ice.
8 It consists o& a main !od+ and a stem 7ic raises or lo7ers a
gateB across te &luid &lo7. In ig pressure installations te gatesmust !e o& ea0+ construction and are sometimes di&&icult to open.Some are motor operated and some a0e a small !+-pass line &ore:uali;ing te pressure on !ot sides o& te gate !e&ore opening.
8 "e rising stem gate 0al0e is used in !ot 7ater and process piping.
It re:uires more o0erall space &or installation9 !ut is used to anad0antage in andling corrosi0e streams tat tend to damage stemtreads in oter t+pe 0al0es.
7/24/2019 11. Valves and Piping
39/118
%
Val0es
Gate 0al0es
7/24/2019 11. Valves and Piping
40/118
*4
Val0es
Gate 0al0es
used to minimi;e pressure drop in te open position and to stop &lo7 rater tan to regulate it.
7/24/2019 11. Valves and Piping
41/118
*1
Val0es
Glo!e 0al0es
8 "e essential &eature o& tis t+pe 0al0e is a glo!ular !od+ 7it aninternal9 ori;ontal partition a0ing a circular opening in 7ic isinserted a ring or seat. "e glo!e or disc seats on tis ring to e&&ectsut-o&&.
8 "e 0al0e opening is so arranged tat &lo7 troug it must ma3e t7o
4-degree canges o& direction. "is results in a relati0el+ igpressure drop9 or resistance to &lo7.
8 "e glo!e 0al0e is generall+ used in small si;ed piping &or trottlingor control. "e+ are used principall+ in steam or air ser0ice 7eretrottling and a positi0e sut-o&& is desira!le.
8 Installation sould !e suc tat &lo7 is up troug te seat ring andagainst te !ottom o& te disc or glo0e. "is 7ill pre0ent openingdi&&iculties caused !+ te accumulation o& de!ris a!o0e te disc."is sould !e a0oided.
7/24/2019 11. Valves and Piping
42/118
*2
Val0es
Glo!e 0al0es
7/24/2019 11. Valves and Piping
43/118
*%
Val0es
Glo!e 0al0es - o&&er ease in trottling
7/24/2019 11. Valves and Piping
44/118
**
Val0es
iapragm 0al0es
7/24/2019 11. Valves and Piping
45/118
*,
Val0e
iapragm 0al0es
limited to ,4psi9 e$cellent &or &luid containing suspended solids
iapragm 0al0es
7/24/2019 11. Valves and Piping
46/118
*
Val0es
Plug 0al0es8 "e plug 0al0e9 or coc39 is a conical plug 7itin a !od+. Its cie&
ad0antage is in its tigt sut o&&. A one :uarter
7/24/2019 11. Valves and Piping
47/118
*
Val0es
Plug 0al0e &or trottling ser0ice9 little li3eliood o& lea3age 7en
closed.
7/24/2019 11. Valves and Piping
48/118
*/
Val0es
(all 0al0es8 (all 0al0es are adaptations o& plug 0al0es using !all-saped discsinstead o& conical plugs located 7itin te !od+. A ole troug tecenter o& tis disc pro0ides te straigt-troug &lo7 7ic iscaracteristic o& !all 0al0es. (all 0al0es are used to sut o&& orpermit &ull &lo7 o& &luid troug te 0al0e.
8 (all 0al0es a0e all te ad0antages o& plug 0al0es in terms o&e$cellent &lo7 caracteristics - :uic3 opening9 straigt-troug &lo79minimum tur!ulence9 tigt closure and compactness - plus teadditional ad0antage o& not re:uiring an+ lu!rication or sealant."e+ acie0e tigt closure !+ esta!lising a controlled s:uee;e o&te !all against te sear rings 7ic are made o& plastic materialsuc as te&lon.
7/24/2019 11. Valves and Piping
49/118
*
Val0e
(all 0al0es
7/24/2019 11. Valves and Piping
50/118
,4
Val0es
(utter&l+ 0al0es8 "e !utter&l+ 0al0e deri0es its name &rom te 7ing-li3e action o& te
disc 7ic operates at rigt angles to te &lo7. Frdinaril+9 te+ are
not intended &or tigt sut o&&9 !ut resilient seats a0e !roadened
teir possi!ilities and te+ are no7 &re:uentl+ ad0ertised as a0ing
!u!!le tigtB closure.
7/24/2019 11. Valves and Piping
51/118
,1
Val0es
(utter&l+ 0al0e
7/24/2019 11. Valves and Piping
52/118
,2
Val0es
Needle 0al0es8 Needle 0al0es are designed to gi0e 0er+ &ine control o& &lo7 in small
diameter piping s+stems. "e+ get teir name &rom teir sarp-
pointed conical disc and matcing seat. "e stem treads are &ine
so tat more turns o& te and 7eel are re:uired to increase or
decrease te opening troug te seat.
7/24/2019 11. Valves and Piping
53/118
,%
Val0es
Needle Val0es o&&er &lo7 ad'ustment on small lines
7/24/2019 11. Valves and Piping
54/118
,*
Val0es
Cec3 0al0es8 Cec3 0al0es are automatic in operation. "e+ pre0ent &lo7 in one
direction9 !ut allo7 it in te oter. "ese 0al0es sould !e care&ull+
cec3ed &or direction o& &lo7 in lines.
8 S7ing cec3 0al0es are unsuita!le &or use in 0ertical lines. Note
importance o& correct installation o& a cec3 0al0e in relation to te
stream &lo7. suall+ te 0al0e !od+ as &eatures tat indicate correct
direction.
8 Sometimes an arro7 indicates te direction o& &lo7 permitted troug
te 0al0e. o not rel+ upon a cec3 0al0e to gi0e &ull sut-o&& against a
!ac3 &lo7. Fnl+ on special occasions9 Jautori;edK 7ill te cec3 0al0e
!e depended upon to pre0ent !ac3 &lo7 o& li:uid or oter a;ardousmaterial 7en opening lines into oter s+stems or to te atmospere.
Al7a+s use a !loc3 0al0e 7en possi!le.
7/24/2019 11. Valves and Piping
55/118
,,
Val0es
Sa&et+ 0al0es8 Sa&et+ 0al0es are installed in strategic locations to pro0ide pressure
relie& &or process e:uipment su!'ected to e$cessi0e pressure.
8 A sa&et+ 0al0e consists o& si$ !asic parts spring9 spindle or stem9
ad'usting scre79 disc9 no;;le or seat9 and !od+. Sa&et+9 or relie&9
0al0es are intended &or emergenc+ protection onl+ and sould not!e used as an operating 0al0e.
8 #re:uent poppingB o& a relie& 0al0e contri!utes to teir &ailure9
tere&ore9 te+ sould set at 2, a!o0e 7or3ing pressure. #or
e$ample9 relie& 0al0es on te discarge o& reciprocating pumps 7ill
relie0e 7it eac pump stro3e i& te set pressure is too lo7.Continuous pounding o& te disc upon te seat causes damage and
resultant lea3age o& te 0al0e.
7/24/2019 11. Valves and Piping
56/118
,
Val0es
Sa&et+ 0al0es
7/24/2019 11. Valves and Piping
57/118
,
Pressure Delie0ing e0ices
Con0entional Delie& Val0e
# i F& V l
7/24/2019 11. Valves and Piping
58/118
,/
#unctions F& Val0es
8Piping s+stem9 in order to e&&ecti0el+ per&orm te &unction o&transporting &luids &rom te point to anoter9 need de0ices to control
or regulate te &lo7 o& &luids. Altoug de0ices are a0aila!le 7ic
!+ suita!le instrumentation automaticall+ regulate or control te &lo7
o& &luids in response to &lo79 le0el9 pressure9 temperature9 or oter
control signals onl+ manuall+ operated de0ices 7ill !e discussed
in tis section. Cec3 0al0es9 relie& 0al0es9 steam traps9 drain
0al0es9 etc altoug not manuall+ operated are also discussed in
tis section.
8 Manuall+ operated 0al0es are de0ices 7ic are opened or closed
!+ turning a and 7eel or mo0ing9 rotating or oter7ise
manipulating a and le0er or 7renc. Gate9 glo!e9 plug9 !all9
diapragm and !utter&l+ 0al0es are in tis categor+.
7/24/2019 11. Valves and Piping
59/118
7/24/2019 11. Valves and Piping
60/118
4
(asic Control #unctions F& Val0es
8 Starting and stopping #lo7
"o start or stop te &luid &lo7 is te &unction &or 7ic 0al0es are
most generall+ used. Gate9 plug9 !all9 !utter&l+ and diapragm
0al0es e&&ecti0el+ per&orm tis &unction 7it 0er+ little pressure drop
troug te 0al0e.8 Degulating and trottling #lo7
Degulating or trottling &lo7 is most e&&icientl+ per&ormed 7it glo!e9
angle9 or needle 0al0es. "ese 0al0es are seldom used in si;e
a!o0e / inces !ecause o& te di&&icult+ opening and closing te
larger 0al0es against pressure.(utter&l+ and diapragm 0al0es are also e&&ecti0e as regulating or
trottling 0al0es at limited &luid &lo7 caracteristics.
7/24/2019 11. Valves and Piping
61/118
1
(asic Control #unction F& Val0es
7/24/2019 11. Valves and Piping
62/118
2
Application F& Val0e "+pes
Gate 0al0es
8 "e Principal caracteristic o& a gate 0al0e is te &act tat te
&lo7 troug te 0al0e is stopped !+ sliding a relati0el+ &lat
sur&ace9 called a gate or disc9 across te &lo7 pat o& te &luid
and started !+ mo0ing te disc into a cam!er in te 0al0e!onnet out o& te &lo7 pat. Gate 0al0es are most e&&ecti0e &ull+
closed or &ull+ opened. )en &ull+ opened te &luid &lo7s
troug te gate 0al0e in a straigt line 7it 0er+ little pressure
drop.
7/24/2019 11. Valves and Piping
63/118
%
Application F& Val0e "+pes
Glo!e 0al0es
8 Glo!e 0al0es are named a&ter te glo!ular sape o& teir !od+.
"e+ are most suita!le &or trottling &luid &lo7s !ecause o& teir t+pe
o& seating arrangements9 o7e0er9 te+ can also !e used in &ull+
sut o&& and &ull+ open ser0ice
8 Glo!e 0al0es seating is parallel to te line o& &lo7 7it all contact!et7een seat and disc ending 7en &lo7 !egins.
8 "e &luid &lo7 troug a glo!e 0al0e &ollo7s a canging course
7ic causes resistance to &lo7 and considera!le pressure drop.
6o7e0er9 in order to control te &luid &lo7 7e must sacri&ice some
pressure drop.
7/24/2019 11. Valves and Piping
64/118
*
Application F& Val0e "+pes
Angle 0al0es
8 Angle 0al0es are similar to te design o& glo!e 0al0e !ut a0e less
resistance 7ic results in less pressure drop.
8 "e angle 0al0e e&&ecti0el+ utili;es glo!e 0al0e seating principle
7ile pro0iding &or a 4 degree turn in piping. It is less resisting to
&lo7 tan te glo!e 0al0e it displaces. De:uires &e7er 'oints sa0esma3e-up time and la!or.
7/24/2019 11. Valves and Piping
65/118
,
Application F& Val0e "+pes
Needle 0al0es
8 Needle 0al0es are designed to gi0e 0er+ &ine control o& &lo7 in small
diameter piping s+stems.
8 Generall+ used in cemical in'ections to process and deli0er+ lines
7/24/2019 11. Valves and Piping
66/118
Application F& Val0e "+pes
Plug 0al0es
8 "e plug 0al0e is o&ten re&erred to as te oldest mem!er o& te 0al0e
&amil+9 o7e0er9 tis is onl+ true o& te non-lu!ricated t+pe 7ic
ma+ !e considered a modi&ication o& te simple coc3.
8 "e non-lu!ricated plug 0al0e is an e0olution o& te simple plug
coc3. All te ad0antages o& te simple plug coc3 are maintained !utte tendenc+ o& te plug to sei;e or !ind as !een o0ercome !+
canges in te design and construction o& te plug 0al0e. "is as
!een accomplised !+ te use o& 0arious plastics or oter materials
7it lo7 &riction 0alues &or contact or sealing sur&aces. As a result o&
tese canges non-lu!ricated plug 0al0es are no7 a0aila!le &or a
muc greater range o& ser0ice conditions.
8 "e&lon
7/24/2019 11. Valves and Piping
67/118
Application F& Val0e "+pes
Plug 0al0es
7/24/2019 11. Valves and Piping
68/118
/
Application F& Val0e "+pes
(all 0al0es
8 (all 0al0es are adaptations o& plug 0al0es using !all-saped discsinstead o& conical plugs located 7itin te !od+. A ole troug tecenter o& tis disc pro0ides te straigt-troug &lo7 7ic iscaracteristic o& !all 0al0es. (all 0al0es are used to sut o&& orpermit &ull &lo7 o& &luid troug te 0al0e.
8 (all 0al0es a0e all te ad0antages o& plug 0al0es in terms o&e$cellent &lo7 caracteristics - :uic3 opening9 straigt-troug &lo79minimum tur!ulence9 tigt closure and compactness - plus teadditional ad0antage o& not re:uiring an+ lu!rication or sealant."e+ acie0e tigt closure !+ esta!lising a controlled s:uee;e o&te !all against te sear rings 7ic are made o& plastic materialsuc as te&lon.
7/24/2019 11. Valves and Piping
69/118
Application F& Val0e "+pes
(all 0al0es
7/24/2019 11. Valves and Piping
70/118
4
Application F& Val0e "+pes
(utter&l+ 0al0es
8 "e+ are 7idel+ used in te municipal &ield &or te control o& 7ater
&lo7.
8 (utter&l+ 0al0es are e$cellent &or andling large &lo7 o& gases and
li:uid at relati0el+ lo7 pressure.
8 "e !utter&l+ 0al0e in &ull open position as relati0el+ lo7 pressuredrop and minimum tur!ulence since te disc position is parallel to
te &luid &lo7. Some o& te ad0antages o& !utter&l+ 0al0es are little
ead room re:uired9 ligt in 7eigt9 dura!ilit+9 lo7 initial cost and
ease o& operation. 6o7e0er9 te+ are limited in pressure and
temperature applications.
7/24/2019 11. Valves and Piping
71/118
1
Application F& Val0e "+pes
Cec3 0al0es
8 "e principal &unction o& a cec3 0al0e is to automaticall+ pre0ent
re0ersal o& te direction o& te &luid &lo7. Pressure o& te &luid &lo7ing
troug te cec3 0al0e 3eeps it open re0ersal o& te &lo7 closes
it. Most manu&acturers plainl+ mar3 cec3 0al0es &or direction o&
&lo7. "e design o& cec3 0al0es are relati0el+ simple and are
a0aila!le in tree !asicall+ di&&erent t+pes - s7ing cec39 li&t cec39
and !all cec3.
Application F& Val0e "+pes
7/24/2019 11. Valves and Piping
72/118
2
Application F& Val0e "+pes
Cec3 Val0es
8 sed to pre0ent re0ersal o& &lo7 1. S7ing cec3 0al0e
- Normal design is &or use onl+ in ori;ontal lines
2. Li&t cec3 0al0es
- Vertical li&t cec3 0al0e &or installation in 0ertical line9 7ere
te &lo7 is normall+ up7ard - Glo!e cec3 0al0e &or use in ori;ontal lines
- Angle cec3 0al0e used &or installation 7ere a 0ertical line
7it up7ard &lo7 turn ori;ontal
%. "ilting dis3 cec3 0al0e
- Ma+ !e installed !ot ori;ontall+ and 0erticall+. Less pressure
drop at lo7 0elocit+ !ut greater at ig 0elocit+. Arrests
slamming.
7/24/2019 11. Valves and Piping
73/118
%
Application F& Val0e "+pes
S7ing cec3 0al0e
8 S7ing cec3 0al0es a0e a disc9 inged at te top9 7ic seats
against a macined seat in te tilted !ridge 7all opening. "e disc
s7ings &reel+ in an arc &rom te &ull+ closed position to one pro0iding
uno!structed &lo7. "e &luid &lo7s troug te !od+ in a straigt line.
"e straigt line &lo7 results in lo7 pressure drop !ecause o& te
minimum resistance to &lo7.
Application F& Val0e "+pes
7/24/2019 11. Valves and Piping
74/118
*
Application F& Val0e "+pes
Cec3 Val0es
S7ing cec3 0al0e
Application F& Val0e "+pes
7/24/2019 11. Valves and Piping
75/118
,
Application F& Val0e "+pes
"ilting dis3 cec3 0al0e
Cec3 0al0es
7/24/2019 11. Valves and Piping
76/118
Application F& Val0e "+pes
Li&t Cec3 Val0e
8 "e li&t cec3 0al0e as a disc e:uipped 7it a sort guide9 usuall+
a!o0e and !elo79 7ic mo0es 0erticall+ in integral guides in te
cap and !ridge 7all. #luid &lo7 mo0ing troug te !od+ in a
&re:uent canging course 3eeps te 0al0e open.
8 )en &lo7 stops gra0it+ or re0erse o& &lo7 direction automaticall+closes te 0al0e !+ &orcing te disc against te seat. Li&t cec3
0al0es pro0ide a tigter seal against !ac3 &lo7 tan can !e acie0e
7it te s7ing cec3 0al0e.
8 Li&t cec3 0al0es can onl+ !e used in ori;ontal pipe lines and are
generall+ used in con'unction 7it glo!e and angle 0al0es.
7/24/2019 11. Valves and Piping
77/118
Application F& Val0e "+pes
Li&t cec3 0al0e
7/24/2019 11. Valves and Piping
78/118
7/24/2019 11. Valves and Piping
79/118
Application F& Val0e "+pes
(all Cec3 Val0e
8 (all cec3 0al0es are similar to li&t cec3 0al0es e$cept tat a !all is
used in place o& te li&t disc &or closure purposes. "e !all is pused
a7a+ &rom te seat during &luid &lo7 and closes rapidl+ 7en &lo7
stops or is re0ersed. "is 0al0e as e$tensi0e use in piping s+stems
mo0ing ot oils and can onl+ !e used in 0ertical lines.
7/24/2019 11. Valves and Piping
80/118
/4
Application F& Val0e "+pes
Stop-Cec3 or Non-Deturn Val0e
8 A special and more complicated cec3 0al0e called te stop-cec3
or non-return 0al0e is essential to te sa&e operation o& a !oiler.
"eir design must con&orm to te ASME (oiler Construction Code
&or Non-Deturn Stop 0al0es. "e 0al0es are intended to per&orm &our
important &unctions in !oiler steam piping>
1. Act as an automatic non-return 0al0e pre0enting !ac3&lo7 o&
steam &rom te connected main steam eader into te !oiler in te
e0ent o& &ailure o& tat !oiler.
7/24/2019 11. Valves and Piping
81/118
/1
Application F& Val0e "+pes
8 Stop-Cec3 or Non-Deturn Val0e
7/24/2019 11. Valves and Piping
82/118
/2
Application F& Val0e "+pes
Stop-Cec3 or Non-Deturn Val0e
7/24/2019 11. Valves and Piping
83/118
7/24/2019 11. Valves and Piping
84/118
/*
Application F& Val0e "+pes
Sa&et+ 0al0es
8 Applications o& sa&et+ 0al0es 7ill !e discussed separatel+ later in
tis module under pressure relie0ing de0ices.
7/24/2019 11. Valves and Piping
85/118
7/24/2019 11. Valves and Piping
86/118
7/24/2019 11. Valves and Piping
87/118
/
Application F& Val0e "+pes
7/24/2019 11. Valves and Piping
88/118
//
Val0e Datings
Most 0al0e manu&acturers compl+ 7it MSS Standard Mar3ingS+stem SP-2, in te identi&ication o& teir 0al0es. "e &ollo7ings+m!ols are generall+ used>
S - Steam
F - Fil
G - Gas
) - )ater
L - Li:uid
General purpose 0al0es ma+ so7 t7o ser0ice ratings. Fne is asteam rating9 !ased on a speci&ic pressure@temperature condition."e second rating is &or cold ser0ice.
7/24/2019 11. Valves and Piping
89/118
/
Val0es Datings
8 Steam Datings
Steam ratings are used as a !asis &or determining te suita!ilit+ o& a
material &or a gi0en application. #or lo7er temperatures te sa&e
7or3ing pressure o& a material is usuall+ greater tat te steam
rating.
8 Cold Datings
Most 0al0es a0e t7o ser0ice ratings. In addition to te steam
rating9 e$plained a!o0e9 cold ser0ice ratings are usuall+ designated
!+ te mar3 )FG9 7ic stands &or cold 7ater9 oil9 or gas9 non-soc3.
7/24/2019 11. Valves and Piping
90/118
7/24/2019 11. Valves and Piping
91/118
V l F ti A d M i t
7/24/2019 11. Valves and Piping
92/118
2
Val0e Fperation And Maintenance
Variations in Stem Fperation o& Gate9 Glo!e and Angle Val0es
1. Dising stem 7it outside scre7 and +o3e. In tis construction te
stem scre7 remains outside te 0al0e !od+ 7eter 0al0e is opened
or closed. Stem treads are not su!'ected to te e&&ects o& &luids in
te line - suc as caused !+ corrosion9 erosion9 sediment9 etc. "is
construction also permits con0enient lu!rication o& stem treads.
"e rising stem so7s at a glance te position o& te disc.
Ade:uate eadroom must !e pro0ided &or te rising stem 7en te
0al0e is opened9 and te stem sould !e protected against damage7en raised.
7/24/2019 11. Valves and Piping
93/118
o5s And on5t #or (etter Val0e Ser0ice
7/24/2019 11. Valves and Piping
94/118
*
o s And on t #or (etter Val0e Ser0ice
1. on5t e$pose 0al0es to damaging !lo7s. Val0es can5t !e a!usedand still operate e&&icientl+. A !ent stem not onl+ cripples 0al0es9 !utma+ cause a sutdo7n tat results in costl+ dela+ and repair.
2. on5t o0erloo3 lea3s !ig and small. A lea3 in a 0al0e o&ten can
!e remedied simpl+ and in a urr+9 i& caugt in time. Stem lea3snormall+ can !e &i$ed !+ sligtl+ tigtening te pac3ing nut or gland.
Stu&&ing !o$ lea3s usuall+ can !e stopped !+ merel+ pullingB up tepac3ing nut. Fn !olted glands9 care must !e ta3en to tigten !olts
e0enl+O as se0erel+ co3ing te gland 7ill !ind te stem. I& testu&&ing !o$ must !e repac3ed9 tis repair sould !e sceduled &or:uali&ied maintenance mecanics.
7/24/2019 11. Valves and Piping
95/118
o5s And on5t #or (etter Val e Ser ice
7/24/2019 11. Valves and Piping
96/118
o5s And on5t #or (etter Val0e Ser0ice
7/24/2019 11. Valves and Piping
97/118
7/24/2019 11. Valves and Piping
98/118
7/24/2019 11. Valves and Piping
99/118
7/24/2019 11. Valves and Piping
100/118
7/24/2019 11. Valves and Piping
101/118
7/24/2019 11. Valves and Piping
102/118
Pressure Delie0ing e0ices
7/24/2019 11. Valves and Piping
103/118
14%
Pressure Delie0ing e0ices
Sa&et+ Val0es
8 An automatic pressure relie0ing de0ice actuated !+ te static
pressure upstream o& te 0al0e9 and caracteri;ed !+ rapid &ull
opening or pop action upon opening.
8 It is used &or steam9 gas or 0apor ser0ice.
8 Dated capacit+ is reaced at %9 14 or 24 percent o0erpressure9depending upon applica!le code.
Pressure Delie0ing e0ices
7/24/2019 11. Valves and Piping
104/118
14*
Sa&et+-relie& 0al0e8 Sa&et+ relie& 0al0e is an automatic pressure relie0ing de0ice
actuated !+ te static pressure upstream o& te 0al0e andcaracteri;ed !+ an ad'ustment to allo7 eiter a popB or a nonpopB action and a no;;le t+pe entrance
8 Suita!le &or use as eiter a sa&et+ or relie& 0al0e9 depending onapplication.
8 Sa&et+9 relie& and sa&et+ relie& 0al0es are installed in strategic
locations to pro0ide pressure relie& &or process e:uipment su!'ectedto e$cessi0e pressures. "ese 0al0es consist o& si$ !asic parts>spring9 stem9 ad'usting scre79 disc9 no;;le or seat9 and !od+.
8 Dated capacit+ is reaced at % or 14 percent o0erpressure9depending upon code and@or process conditions. Pressure relie0ing0al0es are intended &or emergenc+ protection onl+ and sould not
!e used as an operation 0al0e. #re:uent poppingB o& a relie& orsa&et+ 0al0e contri!utes to teir &ailure and are tere&ore set at 2,- ,4 a!o0e te 7or3ing pressure.
7/24/2019 11. Valves and Piping
105/118
7/24/2019 11. Valves and Piping
106/118
Pressure Delie0ing e0ices
7/24/2019 11. Valves and Piping
107/118
14
Pressure Delie0ing e0ices
Con0entional and !alance sa&et+ 0al0e8 Con0entional sa&et+ 0al0es operate satis&actoril+ onl+ 7en tere is
relati0el+ constant !ac3 pressure. Canges in !ac3 pressure can
seriousl+ a&&ect its operational pressure and &lo7 capacit+
8 (alance 0al0es operate satis&actoril+ under 0ar+ing !ac3 pressure
as tis as little in&luence on per&ormance
7/24/2019 11. Valves and Piping
108/118
7/24/2019 11. Valves and Piping
109/118
e&inition o& Pressure Delie& "erms
7/24/2019 11. Valves and Piping
110/118
114
e&inition o& Pressure Delie& "erms
2. F0erpressure8 Pressure increase o0er te set pressure o& te primar+ relie0ing
de0ice is o0er pressure
8 It is te same as accumulation 7en te relie0ing de0ice is set at
te ma$imum allo7a!le 7or3ing pressure o& te 0essel
e&inition o& Pressure Delie& "erms
7/24/2019 11. Valves and Piping
111/118
111
e&inition o& Pressure Delie& "erms
%. Accumulation8 Pressure increase o0er te ma$imum allo7a!le 7or3ing pressure
o& te 0essel during discarge troug te sa&et+ or relie& 0al0e9
e$pressed as a percent o& tat pressure.
e&inition o& Pressure Delie& "erms
7/24/2019 11. Valves and Piping
112/118
112
e&inition o& Pressure Delie& "erms
*. Ma$imum allo7a!le 7or3ing pressure8 "e ma$imum allo7a!le 7or3ing pressure o& an un&ired pressure
0essel is tat pressure determined !+ code re:uirements9 te
metal material o& construction and its operating temperature9
a!o0e 7ic te 0essel ma+ not !e operated
8 #or a gi0en metal temperature9 tis pressure is te igestpressure at 7ic te sa&et+ de0ice ma+ !e set to open.
7/24/2019 11. Valves and Piping
113/118
e&inition o& Pressure Delie& "erms
7/24/2019 11. Valves and Piping
114/118
11*
e&inition o& Pressure Delie& "erms
. (lo7do7n8 "e reduction in &lo7ing pressure !elo7 te set point re:uired &or
a de0ice to close
8 Is te di&&erence !et7een te set pressure and te reseating
pressure o& a sa&et+ or relie& 0al0e
8 E$pressed as percent o& te set pressure or psi
7/24/2019 11. Valves and Piping
115/118
7/24/2019 11. Valves and Piping
116/118
Electric Solenoid
7/24/2019 11. Valves and Piping
117/118
11
"ermal Val0e
7/24/2019 11. Valves and Piping
118/118