Post on 04-Jul-2020
MIZU BLOC BASIN SET
CLEANING RECOMMENDATIONS
To see the complete Mizu range go to www.reece.com.au/bathrooms
SPECIFICATIONSRecommended use Domestic, hotel and commercial.
Colour Chrome
Pressure Rating Maximum continuous operating pressure 1000kPa.
For best performance and longer life we recommend 150-500kPa.
Hot and cold water inlet pressure should be equal.
Temperature Rating Maximum continuous working temperature 80°
Suitable Hot Water Units
Storage Tank: Yes
Continuous Flow: Yes
Gravity Feed: Yes
WELS 4 Star
Flow Rate: 7.5 L/min
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions.
WaterMarkAS/NZS 3718WMKA 02260
TM
Dimensions are nominal measurements only.
< =1 = > ?@ A ' -
B C14.1 2.30 D C
" # $% &
' ( ) !
* +, (
' -
. /0 1
2 34 5
6 7 8 9 :
!* ; E F
MIZU BLOC BASIN SET
CT4203
CT9505802
16
26
50
50
50
52
52
34
34
140
208
205
88
155@ A '
14.1 2.30 D C
" # $% &
' ( ) !
* +, (
' -
. /0 1
2 34 5
6 7 8 9 :
!* ; E F
16
26
50
50
50
52
52
34
34
140
208
205
88
155
page 1 of 3
The more stars the more water efficient
WATER RATINGwww.waterrating.gov.au
In accordance with AS/NZS 6400
Licence No. 0025Reece Limited
7.5 litres per minute
MIZUBloc BASIN SET
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
INSTAllATIoN
Note
Ensure water lines are flushed free of impurities
1. Attach stop bodies (14) to tee-piece (22). Fully tighten connections, but do not overtighten.
2. Insert stop bodies through basin holes ensuring that housing thread extends above basin level
3. Adjust and fix stop bodies (14) into position using locking nuts (10)
4. Separate cartridge locknut and fibre washer (9) from cartridge (12).
5. Grip the cartridge on the hexagonal flats and install cartridge fully into stop body until it comes to a firm stop. Do not tighten cartridge into position by rotating spindle.
6. Turn spindle to off position and turn on water at mains. Check that cartridge has fully seated. If dripping occurs then gentle tighten cartridge further until dripping stops.
7. Firmly tighten cartridge fibre washer (9) and cartridge locknut (7) into position.
8. Place base flange (8) into base of cartridge bonnet (5) and secure down onto cartridge by tightening bonnet by hand.
9. Turn cartridge to fully OFF position.
10. Assemble handle (1) onto spindle and secure in place by fixing with spanner provided.
11. Place locknut (20), and rubber washer (19) onto outlet spigot of tee piece (22).
12. Ensure rubber o-ring is inserted in underside of spout base flange (18)
13. Push outlet through basin top and over o-rings (21) of tee-piece.
14. From underneath, fix outlet into position by tightening locknut (20) onto outlet thread.
O RING
重量数量 比例图 样 标 记
第 张共 张
DR BRASS (ALLOY486)
AERATOR ADAPTOR DR BRASS (ALLOY486)
16x OUTLET
PLASTIC AERATOR
DELRIN 500P NC010
DR BRASS (ALLOY486)INSERTSDR BRASS (ALLOY486)BASIN RECESS BODY
DR BRASS (ALLOY486)
DR BRASS (ALLOY486)
BRASS (ALLOY370)
LOCK NUT
HANDLE
NYLON OLIVE
WASHER EPDM 70
TOP ASSEMBLIES
FIBRE WASHERBASE FLANGENUT
QUADRATE FLANGE BRASS (ALLOY370)
LOCK NUT
LOCK NUT
BRASS (ALLOY370)
BRASS (ALLOY370)
CIRCLIP STAINLESS STEEL
周莲群
签 字
标准化
日 期
审 定
批 准
标记
设 计
处数
校 对
工 艺
更改文件号
日 期审 核 陈 波
描 图
描 校
借通用件登记
旧底图总号
版本
签字
日期
日 期
周莲群
签 字
标准化
审 定
批 准
标记
设 计
处数
校 对
工 艺
更改文件号
日 期审 核
重量数量 比例图 样 标 记
第 张共 张
NO PRODUCT NAME QTY MATERIAL123456789
222222222
MIZU BLOC WALLTOP ASSEMBLIES
WASHER EPDM 70"T" PIECE COPPER
WASHERPLASTIC LOCK NUT ABS
EPDM 70QUADRATE FLANGE
BOLT STAINLESS STEEL
DR BRASS (ALLOY486)
COMPRESSTION NUT DR BRASS (ALLOY486)
210
HANDLE
LOCK NUT
CIRCLIP
LOCK NUT BRASS (ALLOY370)
STAINLESS STEEL
BRASS (ALLOY370)
BRASS (ALLOY370)
QUADRATE FLANGE BRASS (ALLOY370)
BOLT STAINLESS STEEL
NUT
BASE FLANGE BRASS (ALLOY370)
BRASS (ALLOY370)
FIBRE WASHER
CT4100
MIZU BLOC BASIN SET
CT4203
BRASS (ALLOY370)TOP ASSEMBLIES
CT9505802
CT9505803
方管子
Exploded ViewItem Description
1. Handle
2. Lock Nut
3. Circlip
4. Lock Nut
5. Wall Flange
6. Bolt
7. Nut
8. Handle
9. Fibre Washert
10. Lock Nut
11. Washer
12. Top Assemblies
13. Inserts
14. Basin Recess Body
15. Nylon Olive
16. Compression Nut
17. Outlet
18. Wall Flange
19. Washer
20. Lock Nut
21. O Ring
22. T Piece
23. Washer
24. Aerator Adaptor
25. Aerator
page 2 of 3
MIZUBloc BASIN SET
REEcE PRoDUcT QUAlITY GUARANTEEYou have purchased a quality product from Reece Pty Ltd ABN 84 004 097 090 (“Reece”). This product is covered by a 7 year replacement product warranty and a 12 month warranty over spare parts and labour.
7 YEAR WARRANTY – DoMESTIc USEThis warranty covers faults in the product construction, material and assembly. Products which are within 7 years from the date of purchase, found upon inspection by an authorised Reece representative, to be defective in construction, material or assembly, will be repaired or exchanged with an equivalent product free of charge. Replaced items become Reece’s property. This warranty also covers any spare parts included under “Manufacturer’s Provisions” below.
All replacement products will be available for collection without charge to the customer at the nearest Reece branch to the customer’s location, or elsewhere as agreed between the customer and Reece.
Manufacturer’s ProvisionsThe following spare parts are covered by a 7 year warranty:
• Mixer Cartridge
labour and Spare PartsThe labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier within 1 year from the date of purchase.
Spare parts other than those listed in the Manufacturer’s Provisions above, which are within 1 year from the date of purchase found upon inspection by an authorised Reece representative to be defective in construction, material or assembly, will be replaced free of charge.
Warranty conditionsThis warranty will apply only under all of the following conditions:
• The item has been installed by a licensed plumber
• The item has been installed for and subjected to domestic residential use only
• Failure is due to a fault in the manufacture of the product
• Proof of purchase (including the date of purchase) is provided
• The installation of the product is in accordance with the instructions provided
This warranty does not cover products purchased as an ex-display without being fully checked and tested for sale by the manufacturer.
This warranty does not include faults caused by:
• Unsuitable or improper use
• Incorrect installation or installation not in accordance with the instructions provided
• Installation or part installation by the purchaser or any person other than a LICENSED PLUMBER
• Normal wear and tear
• Inadequate or complete lack of maintenance
• Chemical, electrochemical or electrical influences
• Harsh detergents or abrasive cleaners used on product finishes
1 YEAR WARRANTY – coMMERcIAl USE‘Commercial’ use is all use other than for normal domestic residential purposes, including use in non-business places as in public buildings, schools, sports centres and in establishments that contain private bathrooms with high frequency of use by many individuals, such as hotels, motels, retirement villages and hospitals.
The Commercial warranty covers this product against manufacturing faults in the construction, material and assembly of both the finished products and any spare parts for a period of 1 year from the date of purchase. Products and spare parts which are found upon inspection by an authorised Reece representative to be defective in construction, material or assembly will be repaired or exchanged free of charge. Replaced items become Reece’s property. The labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier. The Warranty Conditions and exclusions which apply to the domestic use warranty also apply to this commercial warranty.
EXclUSIoNSTo the fullest extent permitted by law, Reece excludes all liability for damage or injury to any person, damage to any property, and any indirect consequential or other loss or damage.
clAIM PRocEDUREFor all warranty queries customers are to contact the branch where the product was purchased. These details can be found on your purchase invoice.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
TAP.
T1.7
YR
Don’t risk it, use a licensed plumber.™
7YEARQ
U
ALITY GUARANTEE
Cartridges
page 3 of 3